The Galv Process

ACME A-FILES
THE GALVANIZING PROCESS
SURFACE PREPARATION
Surface preparation is the most important step in the application of any
coating. In most instances, where a coating fails before the end of its
expected service life, it is due to incorrect or inadequate surface preparation.
With galvanizing, the surface preparation process contains its own

built-in means of quality assurance and quality control in that zinc
will simply not react with a steel surface that is not perfectly clean.
Any failures or inadequacies in surface preparation will be immediately
apparent when the steel is withdrawn from the molten zinc and uncoated
areas remain, and immediate corrective action is taken.
Conversely, a barrier coating applied by brush or spray to an inadequately

prepared surface can pass initial inspection but fail on the job weeks, months
or even years later, before the end of the expected service life of the coating.
Hot dip galvanizing is a factory-applied coating, and as such, primary

responsibility for surface preparation as well as coating application falls with
the galvanizer.
Surface preparation for galvanizing typically consists of three steps:

ACME A-FILES
Caustic Cleaning — A hot alkali solution is often used to remove organic

contaminants like dirt, paint markings, grease, and oil from the metal
surface. Epoxies, vinyls, asphalt, or welding slag must be removed by grit
blasting, sand blasting, or other mechanical means, before galvanizing.
Removal of these materials is usually the responsibility of the fabricator.
Pickling — Scale and rust are normally removed from the steel surface
by pickling in an ambient temperature hydrochloric acid.
Fluxing — Fluxing is the final surface preparation step in the galvanizing

process. Fluxing removes oxides and prevents further oxides from forming
on the surface of the metal prior to galvanizing and promotes bonding of
the zinc to the steel or iron surface. In the dry galvanizing process, the
steel or iron materials are dipped or "prefluxed" in an aqueous solution of
zinc ammonium chloride. The material is then dried prior to immersion in
molten zinc.
GALVANIZING
In this step, the material is completely immersed in a bath consisting of a

minimum 98 percent pure molten zinc. The bath chemistry is specified by the
American Society of Testing and Materials in Standard A 123. The bath
temperature is maintained at approximately 830 degrees Fahrenheit.
Fabricated items are immersed in the bath long enough to reach bath
temperature. The articles are slowly withdrawn from the galvanizing bath,
and the excess zinc is removed by draining. The chemical reactions that
result in the formation and structure of the galvanized coating continue after
the articles are withdrawn from the bath as long as these articles are near
bath temperatures. The articles are air cooled after withdrawal from the
bath.
COATING THICKNESS
ASTM and CSA specifications and inspection standards for galvanizing

recognized that variations inherently occur in both coating thickness and
compositions. Thickness specifications are stated in both average terms and
as a minimum for any individual articles tested. Further, coating thickness
measures must be taken a several points on each inspected article to comply
with ASTM A 123.
ASTM specifications establish minimum standards for thickness of galvanized

coatings on various categories of items. By the nature of the galvanizing
process, the minimum standards specified by ASTM are routinely exceeded
ACME A-FILES
by galvanizers. Factors influencing the thickness and appearance of the

galvanized coating include:
• Chemical composition of the steel

• Steel surface condition
• Cold working of steel prior to galvanizing
• Bath immersion time
• Bath withdrawal rate
• Steel cooling rate
The chemical composition of the steel being galvanized is very important.
The amount of silicon and phosphorus present in the steel strongly influences
the thickness and appearance of the galvanized coating. A silicon level of
0.04 percent or greater or a phosphorous level of 0.05 percent or greater in
the steel will generally result in thick coatings consisting primarily of zinc-iron
alloys. The carbon, sulfur, and manganese content of the steel also may have
a minor effect on the galvanized coating thickness.
Certain steel compositions tend to accelerate the growth of zinc-iron layers.

This may result in a finished galvanized coating consisting entirely of zinc-
iron alloy. Instead of the shiny spangled appearance, the galvanized coating
will have a dark gray, matte finish. This dark gray, matte galvanized coating
will provide as much corrosion protection as a galvanized coating having the
common spangled appearance.
As the galvanizing reaction is a diffusion process, higher zinc bath

temperatures and longer immersion times will generally produce somewhat
heavier alloy layers. Like all diffusion processes, however, the reaction
proceeds rapidly at first and then slows as layers grow and become thicker.
Continued immersion beyond a certain time will have little incremental effect.
In galvanizing of silicon bearing steels containing more than 0.04 percent
silicon, the diffusion process significantly changes.
The thickness of the outer pure zinc layer is largely dependent upon the rate
of withdrawal from the zinc bath. A rapid rate of withdrawal causes an article
to carry out more zinc and generally results in a thicker coating.
ASTM and CSA specifications and inspection standards for galvanizing

recognized that variations inherently occur in both coating thickness and
compositions. Thickness specifications are stated in both average terms and
as a minimum for any individual articles tested. Further, coating thickness
measures must be taken a several points on each inspected article to comply
with ASTM A 123.
ACME A-FILES
THE METALLURGICAL BOND
Galvanizing forms a metallurgical bond between the coating and underlying

steel or iron. Galvanizing creates a barrier that is a part or extension of the
metal itself. During galvanizing, the molten zinc reacts with the surface of
the steel or iron article undergoing galvanizing to form a series of zinc/iron
alloys. A typical galvanized coating consists of three alloy layers and a layer
of metallic zinc. Moving from the underlying metal surface outward, these
are:
• The thin Gamma layer composed of an alloy that is 75 percent zinc

and 25 percent iron
• The Delta layer composed of an alloy that is 90 percent zinc and 10
percent iron
• The Zeta layer composed of an alloy that is 94 percent zinc and 6
percent iron
• The outer Eta layer that is composed of zinc
Each layer is characterized by a measure of hardness called the Diamond

Pyramid Number (DPN). The DPN is a progressive measure of hardness (i.e.,
the higher the number the greater the hardness). Typically, the Gamma,
Zeta, and Delta layers are harder than the underlying steel. The
hardness of these inner layers provides exceptional protection
against coating damage through abrasion. The Eta layer of the
galvanized coating is quite ductile, providing the galvanized coating with
good resistance to damage by abrasion.
The galvanized coating is adherent to the underlying steel on the order of

several thousand pounds per square (psi) inch. Other coatings typically offer
adhesion rated at several hundred psi at best.
These three factors, hardness, ductility, and adherence combine to

provide the galvanized coating with unmatched protection against
ACME A-FILES
damage by rough handling during transportation to and/or at the job

site as well as on the job. The toughness of the galvanized coating is
extremely important since barrier protection from corrosion is dependent
upon the integrity of the coating. Other coatings damage easily during
shipment or through rough handling on the job site. Experts will argue
that all organic forms of barrier protection (such as paint) must be
permeable to some degree. Correctly applied galvanized coatings are
impermeable.
If the coating is physically damaged, the galvanizing will continue to provide

cathodic protection to the exposed steel. If individual areas of underlying
steel or iron of length and/or width of as much as 1/4" become exposed, the
surrounding zinc will provide these areas with cathodic protection for as long
as the coating lasts.
The galvanizing process naturally produces coatings that are at least as thick
on the corners and edges as the coating on the rest of the article. As coating
damage is most likely to occur at the edges, this is where added protection is
needed most. Brush- or spray-applied coatings have a natural tendency to
thin at the corners and edges.
Because the galvanizing process involves total immersion of the

material, it is a complete process; all surfaces are coated.
Galvanizing provides both outside and inside protection for hollow
structures. Conversely, hollow structures that are painted have no corrosion
protection on the inside.
The inspection process for galvanized items is simple, fast and

requires minimal labor. This is important because the inspection process
required to assure the quality of many brush- and spray-applied coatings is
highly labor intensive and uses expensive skilled labor.
The Galvanizing process can be done under any weather or humidity

conditions. Most brush- and spray-painted coatings are dependent upon
proper weather and humidity conditions for correct application. The
dependence of most brush- or spray-applied corrosion systems upon proper
weather and humidity conditions often translate into costly construction
delays at the job site.
The galvanizer's ability to work in any type of weather allows a higher degree
of assurance of on-time delivery. Working under these circumstances,
galvanizing can be completed with short lead and turnaround times.
A turnaround time of two or three days for galvanizing is common,
and a week is standard.
ACME A-FILES
INSPECTION
The most important method of inspection for galvanized articles is visual. A

variety of simple physical and laboratory tests may be performed for:
• Thickness
• Uniformity of the coating
• Adherence of the coating
• Appearance
Products are galvanized according to the long established, well accepted, and
approved standards of the American Society for Testing and Materials
(ASTM). Additional relevant standards are provided by the Canadian
Standards Association (CSA) and the American Association of State Highway
and Transportation Officials (AASHTO). ASTM standards cover everything
from the minimum required coating thicknesses for various categories of
galvanized items to the composition of the zinc metal used in the process.
CHARACTERISTICS OF GALVANIZED SURFACES
Three factors — hardness, ductility, and adherence — combine to give

galvanized coatings unmatched resistance to damage by corrosion or rough
handling.
• Hardness. Each layer of the galvanized surface is characterized by a

measure of hardness called the Diamond Pyramid Number (DPN). The
higher the DPN, the greater the hardness. Typically, the Gamma, Zeta,
and Delta layers are harder than the underlying steel. This provides
excellent resistance to damage from abrasion.
• Ductility. The Eta layer of the galvanized coating is quite ductile, or
pliable, adding to the coating's abrasion resistance.
• Adherence. A galvanized coating is adherent to the underlying steel
at several thousand pounds per square inch (psi). Other coatings
typically offer adhesion rated at several hundred psi at best.

The Galv Process

Uploaded by

Copyright:

Available Formats

The Galv Process

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

The Galv Process

Uploaded by

Copyright:

Available Formats

ACME A-FILES

THE GALVANIZING PROCESS

With galvanizing, the surface preparation process contains its own

Conversely, a barrier coating applied by brush or spray to an inadequately

Hot dip galvanizing is a factory-applied coating, and as such, primary

Surface preparation for galvanizing typically consists of three steps:

Caustic Cleaning — A hot alkali solution is often used to remove organic

Fluxing — Fluxing is the final surface preparation step in the galvanizing

In this step, the material is completely immersed in a bath consisting of a

ASTM and CSA specifications and inspection standards for galvanizing

ASTM specifications establish minimum standards for thickness of galvanized

by galvanizers. Factors influencing the thickness and appearance of the

• Chemical composition of the steel

Certain steel compositions tend to accelerate the growth of zinc-iron layers.

As the galvanizing reaction is a diffusion process, higher zinc bath

ASTM and CSA specifications and inspection standards for galvanizing

THE METALLURGICAL BOND

Galvanizing forms a metallurgical bond between the coating and underlying

• The thin Gamma layer composed of an alloy that is 75 percent zinc

Each layer is characterized by a measure of hardness called the Diamond

The galvanized coating is adherent to the underlying steel on the order of

These three factors, hardness, ductility, and adherence combine to

damage by rough handling during transportation to and/or at the job

If the coating is physically damaged, the galvanizing will continue to provide

Because the galvanizing process involves total immersion of the

The inspection process for galvanized items is simple, fast and

The Galvanizing process can be done under any weather or humidity

The most important method of inspection for galvanized articles is visual. A

CHARACTERISTICS OF GALVANIZED SURFACES

Three factors — hardness, ductility, and adherence — combine to give

• Hardness. Each layer of the galvanized surface is characterized by a

You might also like