WWW.EASAQUESTIONPAPERS.BLOGSPOT.

COM PART -66 MODULE 4 PART -3

Visit to download all latest EASA / DGCA CAR 66 Module examination Question papers and study material

Option C. two or more layers connected in

2. Printed Circuit Boards. series.
1(www.dgcaquestionpapers.in), Like us on Facebook @ fb/DGCAQuestionPapers ( All CAR 66 Module Exam QP Available

Correct Answer is. two or more layers on one

or both sides.
Question Number. 1. When compared Explanation. CAIPs MMC/1-1 Para 15.
to a system that is constructed on one board, a
modular system using Printed Circuit Boards (PCBs)
is.
Option A. harder to fault find. Question Number. 5. When removing a
Option B. more expensive for spares. microprocessor.
Option C. easier to fault find. Option A. ensure the power is OFF to avoid
Correct Answer is. easier to fault find. static discharge.
Explanation. NIL. Option B. no damage is done by static
discharge.
Option C. considerable damage can be done
Question Number. 2. A Printed Circuit by static discharge.
Board (PCS) is constructed of a plastic laminate Correct Answer is. considerable damage can
which has bonded to one or both sides. be done by static discharge.
Option A. a thin sheet of copper. Explanation. NIL.
Option B. various thicknesses of copper.
Option C. a thick sheet of copper.
Correct Answer is. a thin sheet of copper. Question Number. 6. On a PCB, a
Explanation. NIL. decoupling capacitor is used to get rid of transient
currents between which points?.
Option A. The electronic circuit and the
Question Number. 3. How is a PCB aircraft ground.
protected after manufacture?. Option B. The negative rail and the rest of
Option A. By conformal coating. the circuit.
Option B. With non-conductive varnish. Option C. Interspaced along the circuit.
Option C. With wax. Correct Answer is. Interspaced along the
Correct Answer is. By conformal coating. circuit.
Explanation. Although varnish is often used on Explanation. The decoupling capacitor
PCBs, 'conformal coating' is the name of the decouples the AC signal from the DC quiescent
process usually applied to aircraft use PCBs. current.
Aircraft Electricity and Electronics 5th Edition
Eismin Page 120.
Question Number. 7. A decoupling
capacitor in a PCB is used to.
Question Number. 4. A multi-layer PCB Option A. minimise transient currents.
has. Option B. pass DC only.
Option A. two or more layers on one or both Option C. pass AC only.
sides. Correct Answer is. pass AC only.
Option B. one layer on either side.
Page

DOWNLOAD OUR MOBILE APP FROM PLAY STORE @DGCA QUESTION PAPERS
IF YOU HAVE PREVIOUS SESSION QUESTION PAPERS, SHARE WITH US AT [email protected]
 WWW.EASAQUESTIONPAPERS.BLOGSPOT.COM PART -66 MODULE 4 PART -3

Visit to download all latest EASA / DGCA CAR 66 Module examination Question papers and study material

Explanation. A decoupling capacitor decouples Question Number. 1. The output of a

the AC from the DC in a signal, and blocks the DC. tachogenerator is.
2(www.dgcaquestionpapers.in), Like us on Facebook @ fb/DGCAQuestionPapers ( All CAR 66 Module Exam QP Available

Option A. proportional to speed of rotation.

Option B. proportional to position.

Question Number. 8. What is the base Option C. proportional to acceleration.
material of a PCB?. Correct Answer is. proportional to speed of
Option A. Insulator. rotation.
Option B. Semiconductor. Explanation. NIL.
Option C. Conductor.
Correct Answer is. Insulator.
Explanation. Insulator. Aircraft Electricity and Question Number. 2. AC power to a
Electronics 5th Edition Eismin Page 122. synchro system is supplied to.
Option A. torque transmitter only.
Option B. both the torque receiver and
Question Number. 9. In a printed circuit torque transmitter.
board , the surface resistance testing is. Option C. torque receiver only.
Option A. insulation resistance between Correct Answer is. both the torque receiver
adjacent printed conductor. and torque transmitter.
Option B. the resistance between the tow Explanation. NIL.
inductors.
Option C. between the board and the
conductor. Question Number. 3. A differential
Correct Answer is. insulation resistance synchro.
between adjacent printed conductor. Option A. can be used as either a transmitter
Explanation. CAIPs MMC/1-1 para 4.1.7. or a receiver.
Option B. can only be used as a receiver.
Option C. can only be used as a transmitter.

Question Number. 10. What are printed Correct Answer is. can be used as either a
circuit boards made of?. transmitter or a receiver.
Option A. Fibreglass board coated with Explanation. The TDX is a transmitter, the TDR
copper in which circuits are etched. is a receiver.
Option B. Synthetic resin board etched with
copper.
Option C. Matrix board with components Question Number. 4. A resolver has.
soldered on.
Correct Answer is. Fibreglass board coated Option A. 3 coils on the rotor and 2 coils on
with copper in which circuits are etched. the stator.
Explanation. NIL. Option B. 2 coils on the rotor and 3 coils on
the stator.
3a. Servomechanisms. Option C. 2 coils on the rotor and 2 coils on
the stator.
Page

DOWNLOAD OUR MOBILE APP FROM PLAY STORE @DGCA QUESTION PAPERS
IF YOU HAVE PREVIOUS SESSION QUESTION PAPERS, SHARE WITH US AT [email protected]
 WWW.EASAQUESTIONPAPERS.BLOGSPOT.COM PART -66 MODULE 4 PART -3

Visit to download all latest EASA / DGCA CAR 66 Module examination Question papers and study material

Correct Answer is. 2 coils on the rotor and 2

coils on the stator. Question Number. 9. When a
3(www.dgcaquestionpapers.in), Like us on Facebook @ fb/DGCAQuestionPapers ( All CAR 66 Module Exam QP Available

Explanation. NIL. servomotor has stopped, the rate feedback from a

tachogenerator is.
Option A. maximum and in phase.
Question Number. 5. The 'null' point on Option B. maximum and anti-phase.
a control synchro is when the two rotors are. Option C. zero.
Correct Answer is. zero.
Option A. wired in series. Explanation. NIL.
Option B. at 90° to each other.
Option C. parallel to each other.
Correct Answer is. at 90° to each other. Question Number. 10. A tachogenerator
Explanation. NIL. is usually used for.
Option A. angular feedback.
Option B. rate feedback.
Question Number. 6. The rotor of a Option C. position feedback.
desynn indicator is. Correct Answer is. rate feedback.
Option A. an electromagnet. Explanation. NIL.
Option B. a permanent magnet.
Option C. an AC magnet.
Correct Answer is. a permanent magnet. Question Number. 11. Differential
Explanation. NIL. synchros have.
Option A. a transmitter and a receiver.
Option B. a transmitter only.
Question Number. 7. The position Option C. a receiver only.
feedback from a potentiometer is. Correct Answer is. a transmitter and a
Option A. anti-phase. receiver.
Option B. in phase. Explanation. See Pallett Aircraft Instruments
Option C. 90 degrees out of phase. and Integrated Systems pg 135.
Correct Answer is. anti-phase.
Explanation. NIL.
Question Number. 12. In a torque
synchro system, the power supply is connected to.
Question Number. 8. A differential
synchro has. Option A. the rotor windings of both the
Option A. single phase stator, 2 phase rotor. transmitter and receiver.
Option B. the stator windings of the
Option B. 3 phase stator, 3 phase rotor. transmitter.
Option C. 3 phase stator, single phase rotor. Option C. the rotor windings of the
transmitter only.
Correct Answer is. 3 phase stator, 3 phase Correct Answer is. the rotor windings of both
rotor. the transmitter and receiver.
Explanation. NIL. Explanation. Pallett Aircraft Instruments and
Page

Integrated Systems pg 135. Aircraft Electricity and

DOWNLOAD OUR MOBILE APP FROM PLAY STORE @DGCA QUESTION PAPERS
IF YOU HAVE PREVIOUS SESSION QUESTION PAPERS, SHARE WITH US AT [email protected]
 WWW.EASAQUESTIONPAPERS.BLOGSPOT.COM PART -66 MODULE 4 PART -3

Visit to download all latest EASA / DGCA CAR 66 Module examination Question papers and study material

Electronics 5th Edition Eismin Page 185/6.

4(www.dgcaquestionpapers.in), Like us on Facebook @ fb/DGCAQuestionPapers ( All CAR 66 Module Exam QP Available

Question Number. 16. The power supply

to a torque synchro system is.
Question Number. 13. To reduce Option A. AC or DC.
overshoot errors in a synchro. Option B. AC.
Option A. the gain of the amplifier is Option C. DC.
increased. Correct Answer is. AC.
Option B. the system will have velocity Explanation. See Pallett Aircraft Instruments
feedback. and Integrated Systems pg 135.
Option C. the system will have position
feedback.
Correct Answer is. the system will have Question Number. 17. An open loop
velocity feedback. system is one which has.
Explanation. Velocity feedback is used to Option A. no direct feedback loop.
reduce overshoot and oscillations. Option B. rate feedback loop.
Option C. position feedback only.
Correct Answer is. no direct feedback loop.
Question Number. 14. A synchro
transformer is used to. Explanation. Open loop has no feedback.
Option A. add the output of two synchro
transmitters.
Option B. derive an error voltage from a
synchro transmitter signal and a shaft position. Question Number. 18. Mechanical
Option C. obtain a 26 volt AC reference. friction in a servo results in.
Correct Answer is. derive an error voltage Option A. increased inertia.
from a synchro transmitter signal and a shaft Option B. increased damping.
position. Option C. reduced gain.
Explanation. Pallett Automatic Flight Control pg Correct Answer is. increased damping.
135. Explanation. Friction devices are sometimes
used to increase damping and thus decrease
oscillations.
Question Number. 15. Reversal of the
complete power to a torque synchro system will.
Question Number. 19. The position
Option A. displace the receiver rotor by feedback signal is.
180o. Option A. phase advanced by 90° with
Option B. cause reverse rotation of the respect to the input signal.
receiver rotor. Option B. in phase with the input demand
Option C. have no effect. signal.
Correct Answer is. have no effect. Option C. in anti-phase with the demand
Explanation. Since both rotors are supplied with signal.
the same AC, reversing the connections to both Correct Answer is. in anti-phase with the
Page

will have no effect. demand signal.

DOWNLOAD OUR MOBILE APP FROM PLAY STORE @DGCA QUESTION PAPERS
IF YOU HAVE PREVIOUS SESSION QUESTION PAPERS, SHARE WITH US AT [email protected]
 WWW.EASAQUESTIONPAPERS.BLOGSPOT.COM PART -66 MODULE 4 PART -3

Visit to download all latest EASA / DGCA CAR 66 Module examination Question papers and study material

Explanation. The positive feedback must be in Option C. zero.

anti-phase if it is to oppose the demand input. Correct Answer is. zero.
5(www.dgcaquestionpapers.in), Like us on Facebook @ fb/DGCAQuestionPapers ( All CAR 66 Module Exam QP Available

Explanation. Velocity feedback will stop when

the load is at rest.

Question Number. 20. A servo system

that overshoots and oscillates is. Question Number. 24. The primary
Option A. under damped. purpose of rate feedback in a positional servo
Option B. over damped. system is to.
Option C. critically damped. Option A. ensure system linearity.
Correct Answer is. under damped. Option B. prevent excessive overshoot.
Explanation. Oscillations are caused by an Option C. ensure minimum response time.
underdamped system.
Correct Answer is. prevent excessive
overshoot.
Question Number. 21. The power supply Explanation. Rate feedback is to prevent
to a torque synchro system is connected to. excessive overshoot and oscillation.

Option A. the transmitter rotor only.

Option B. the transmitter stator. Question Number. 25. In an AC rate
Option C. the transmitter and receiver servo, a steady input will result in the servomotor.
rotors.
Correct Answer is. the transmitter and Option A. rotating to a new datum position.
receiver rotors.
Explanation. See Pallett Aircraft |Instruments Option B. rotating at a constant speed.
and Integrated Systems pg 135. Option C. oscillating about a new datum.
Correct Answer is. rotating at a constant
speed.
Question Number. 22. In a toroidal Explanation. An AC rate servo is designed to
resistance transmitter indicator system, the power rotate a load (such as a radar dish) at a constant
supply is connected to. speed continually.
Option A. the resistor slab.
Option B. the rotor.
Option C. the brushes. Question Number. 26. In a torque
Correct Answer is. the brushes. synchro that includes a differential synchro the
Explanation. A toroidal resistance indicator is power supply is connected to.
better known as a Desynn indicator. Option A. all three rotors.
Option B. the transmitter and receiver rotors
only.
Question Number. 23. When a servo has Option C. the transmitter rotor only.
reached its null and stopped, the velocity feedback Correct Answer is. the transmitter and
is. receiver rotors only.
Option A. maximum and anti-phase. Explanation. See Pallett Aircraft Instruments
Page

Option B. maximum and in phase. and Integrated Systems pg 135.

DOWNLOAD OUR MOBILE APP FROM PLAY STORE @DGCA QUESTION PAPERS
IF YOU HAVE PREVIOUS SESSION QUESTION PAPERS, SHARE WITH US AT [email protected]
 WWW.EASAQUESTIONPAPERS.BLOGSPOT.COM PART -66 MODULE 4 PART -3

Visit to download all latest EASA / DGCA CAR 66 Module examination Question papers and study material

Explanation. The tachogenerator is to make the

load run at a constant speed.
6(www.dgcaquestionpapers.in), Like us on Facebook @ fb/DGCAQuestionPapers ( All CAR 66 Module Exam QP Available

Question Number. 27. A differential

synchro rotor has.
Option A. three windings. Question Number. 31. The rotor of a
Option B. two windings. torque synchro indicator is.
Option C. one winding. Option A. supplied with an excitation
Correct Answer is. three windings. voltage.
Explanation. See Pallett Aircraft Instruments Option B. connected in series with the
and Integrated Systems pg 135. transmitter stator coil.
Option C. short circuited.
Correct Answer is. supplied with an excitation
Question Number. 28. In a resolver voltage.
synchro the stator windings are electrically Explanation. The excitation voltage is that
displaced by. necessary to magnetise the rotor.
Option A. 90°.
Option B. 180°.
Option C. 120°. Question Number. 32. To increase the
Correct Answer is. 90°. output of a servo amplifier, it is necessary to.
Explanation. Pallett Aircraft Instruments and
Integrated Systems pg 135. Option A. reduce the tacho feedback.
Option B. increase the position feedback.
Option C. increase the tacho feedback.
Question Number. 29. A resolver synchro Correct Answer is. reduce the tacho
output is obtained from a rotor with. feedback.
Option A. two coils at 90°. Explanation. Tachogenerator feedback opposes
Option B. one single coil. the error signal and thus reduces amplifier output.
Option C. three coils at 120°.
Correct Answer is. two coils at 90°.
Explanation. Pallett Aircraft Instruments and
Integrated Systems pg 135. Question Number. 33. Angular
displacement of the control coils with respect to
the reference coils in a two phase induction motor
Question Number. 30. In a speed control are.
servo system (rate control), the purpose of the Option A. 90°, 270°.
tachogenerator is. Option B. 0°, 180°.
Option A. to make the velocity proportional Option C. 90°, 120°.
to servo demand. Correct Answer is. 90°, 270°.
Option B. to make the deflection Explanation. NIL.
proportional to servo demand.
Option C. to make it run at constant speed.
Question Number. 34. A servomotor
Correct Answer is. to make it run at constant having only a tachogenerator as a feedback device
Page

speed. will.

DOWNLOAD OUR MOBILE APP FROM PLAY STORE @DGCA QUESTION PAPERS
IF YOU HAVE PREVIOUS SESSION QUESTION PAPERS, SHARE WITH US AT [email protected]
 WWW.EASAQUESTIONPAPERS.BLOGSPOT.COM PART -66 MODULE 4 PART -3

Visit to download all latest EASA / DGCA CAR 66 Module examination Question papers and study material

Option A. vary its speed with input error Explanation. A small amount of residual voltage
voltage. exists on the output winding of an AC
7(www.dgcaquestionpapers.in), Like us on Facebook @ fb/DGCAQuestionPapers ( All CAR 66 Module Exam QP Available

Option B. null out at a position dependant tachogenerator when it is stationary.

upon input error voltage.
Option C. have a constant speed for any
given input voltage. Question Number. 38. A closed loop
Correct Answer is. have a constant speed for servomechanism.
any given input voltage. Option A. must only have position feedback.
Explanation. With only a tacho feedback it is a
rate servo. Option B. must have both position and
velocity feedback.
Option C. can have either position or velocity
Question Number. 35. The null position feedback.
of a torque synchro system is when. Correct Answer is. can have either position or
Option A. the TX and TR rotors are parallel to velocity feedback.
each other. Explanation. A closed loop servomechanism can
Option B. the TX and TR rotors are 90° to have either position feedback or velocity feedback
each other. or both.
Option C. the TX and TR rotors are 120° to
each other.
Correct Answer is. the TX and TR rotors are Question Number. 39. In a control
parallel to each other. synchro system the power supply is connected to
Explanation. TX and TR rotors must be parallel the.
to be at the null position. Option A. transmitter and receiver rotors.
Option B. transmitter rotor and amplifier.
Option C. receiver rotor and amplifier.
Question Number. 36. An AC Correct Answer is. transmitter rotor and
tachogenerator stator has. amplifier.
Option A. two windings 180° apart. Explanation. Pallett Aircraft Instruments and
Option B. three windings 120° apart. Integrated Systems pg 141.
Option C. two windings 90° apart.
Correct Answer is. two windings 90° apart.
Explanation. NIL. Question Number. 40. Velocity feedback.

Option A. opposes the demand input.

Question Number. 37. When the rotor of Option B. assists the demand input.
an AC tachogenerator is stationary, the rotor has. Option C. prevents dead space errors.
Correct Answer is. opposes the demand
Option A. no magnetic fields. input.
Option B. no circulating currents. Explanation. Velocity feedback is anti-phase to
Option C. low circulating currents. the demand input and opposes it.
Correct Answer is. low circulating currents.
Page

DOWNLOAD OUR MOBILE APP FROM PLAY STORE @DGCA QUESTION PAPERS
IF YOU HAVE PREVIOUS SESSION QUESTION PAPERS, SHARE WITH US AT [email protected]
 WWW.EASAQUESTIONPAPERS.BLOGSPOT.COM PART -66 MODULE 4 PART -3

Visit to download all latest EASA / DGCA CAR 66 Module examination Question papers and study material

Question Number. 41. An increase in other (unlike a torque synchro where they must be
velocity feedback will. parallel to each other).
8(www.dgcaquestionpapers.in), Like us on Facebook @ fb/DGCAQuestionPapers ( All CAR 66 Module Exam QP Available

Option A. decrease the speed the load

moves.
Option B. have no effect on speed. Question Number. 45. In a control
Option C. increase the speed the load synchro the stator current ceases to flow when
moves. the.
Correct Answer is. decrease the speed the Option A. CT rotor is at null.
load moves. Option B. power is removed.
Explanation. Velocity feedback opposes Option C. two rotors are aligned.
demand input therefore it reduces thew speed the Correct Answer is. power is removed.
load moves. Explanation. In a control synchro current flows
in the stator lines at all times, regardless of the
position of the transformer rotor.
Question Number. 42. Rate feedback can
be obtained from a.
Option A. tachogenerator. Question Number. 46. In a rate servo
Option B. synchro. (speed control) the signal into the servo amplifier
Option C. potentiometer. is.
Correct Answer is. tachogenerator. Option A. input voltage plus position
Explanation. A tachogenerator produces rate feedback voltage.
feedback. Option B. input voltage plus tachogenerator
output.
Option C. input voltage minus
Question Number. 43. Positional tachogenerator output.
feedback can be obtained from a. Correct Answer is. input voltage minus
Option A. synchro. tachogenerator output.
Option B. potentiometer. Explanation. In a rate servo the input voltage
Option C. tachogenerator. makes the load rotate and the tachogenerator
Correct Answer is. potentiometer. output (which is negative feedback) prevents it
Explanation. A potentiometer produces rotating too fast.
positional feedback.

Question Number. 47. To reduce

Question Number. 44. The 'null' point in a oscillations about a demand position.
control synchro is when the two rotors are. Option A. the amount of velocity feedback
would be increased.
Option A. at 90° to each other. Option B. the amount of velocity feedback
Option B. wired in series. would be decreased.
Option C. parallel to each other. Option C. the amount of position feedback
Correct Answer is. at 90° to each other. would be increased.
Explanation. In a control synchro the null Correct Answer is. the amount of velocity
position is when the rotors are 90 degrees to each feedback would be increased.
Page

DOWNLOAD OUR MOBILE APP FROM PLAY STORE @DGCA QUESTION PAPERS
IF YOU HAVE PREVIOUS SESSION QUESTION PAPERS, SHARE WITH US AT [email protected]
 WWW.EASAQUESTIONPAPERS.BLOGSPOT.COM PART -66 MODULE 4 PART -3

Visit to download all latest EASA / DGCA CAR 66 Module examination Question papers and study material

Explanation. If velocity feedback is increased, Explanation. To convert a differential synchro

there is more opposition to the demand signal and from subtraction to addition you must swap two of
9(www.dgcaquestionpapers.in), Like us on Facebook @ fb/DGCAQuestionPapers ( All CAR 66 Module Exam QP Available

the load will move slower and oscillations will be the stator leads AND swap two of the rotor leads
reduced. at the differential transmitter.

Question Number. 48. Positive feedback Question Number. 51. Differential

applied to a servomechanism. transmitters are used to.
Option A. increases the response of the Option A. add or subtract two electrical
system. signals.
Option B. opposes the demand signal. Option B. add or subtract a mechanical
Option C. decreases the response of the signal to an electrical synchro signal.
system. Option C. increase the operating speed of
Correct Answer is. increases the response of the synchro receiver.
the system. Correct Answer is. add or subtract a
Explanation. Positive feedback will add to the mechanical signal to an electrical synchro signal.
input of the amplifier and increase the response of Explanation. A differential synchro is used to
the system. add or subtract a mechanical signal from an
electrical signal derived from the synchro
transmitter.
Question Number. 49. A differential
synchro rotor consists of.
Option A. two windings at 90° apart. Question Number. 52. When resolving a
Option B. one winding parallel to the Cartesian input to a Polar output.
transmitter rotor. Option A. the outputs are two voltages.
Option C. three windings at 120° apart. Option B. the inputs are a shaft angle and a
Correct Answer is. three windings at 120° voltage.
apart. Option C. the inputs are two voltages.
Explanation. Pallett Aircraft Instruments and Correct Answer is. the inputs are two
Integrated Systems pg 143. voltages.
Explanation. Cartesian inputs are the X and Y
coordinates and are represented by two voltages.
Question Number. 50. A differential The outputs are represented by a voltage and an
synchro transmitter used for addition has. angular position.

Option A. the TDX S1 and S3 connections

cross connected to the TX. Question Number. 53. A resolver synchro
Option B. the TDX S1 and S3 connections output is obtained from a rotor with.
cross connected to the TR. Option A. one single coil.
Option C. the TDX R1, R3 and S1, S3 Option B. two coils at 90° to each other.
connections cross connected to the TX. Option C. three coils at 120° to each other.
Correct Answer is. the TDX R1, R3 and S1, S3
connections cross connected to the TX. Correct Answer is. two coils at 90° to each
Page

other.

DOWNLOAD OUR MOBILE APP FROM PLAY STORE @DGCA QUESTION PAPERS
IF YOU HAVE PREVIOUS SESSION QUESTION PAPERS, SHARE WITH US AT [email protected]
 WWW.EASAQUESTIONPAPERS.BLOGSPOT.COM PART -66 MODULE 4 PART -3

Visit to download all latest EASA / DGCA CAR 66 Module examination Question papers and study material

Explanation. A resolver synchro has two coils at Option B. mechanical load is high.
90 degrees to each other. Option C. mechanical load is low.
10(www.dgcaquestionpapers.in), Like us on Facebook @ fb/DGCAQuestionPapers ( All CAR 66 Module Exam QP Available

Correct Answer is. mechanical load is low.

Explanation. Torque synchros are used for
Question Number. 54. The output of a indication only, i.e. when the load is low.
resolver synchro is.
Option A. dependant upon the position of
the rotor only.
Option B. proportional to the speed of input Question Number. 58. In a resolver
rotation. synchro the stator windings are electrically
Option C. a function of the rotor position disposed by.
and excitation voltage. Option A. 90°.
Correct Answer is. a function of the rotor Option B. 120°.
position and excitation voltage. Option C. 180°.
Explanation. The output of a resolver synchro is Correct Answer is. 90°.
angular position and a voltage to represent the Explanation. A resolver synchro has the
distance. windings 90 degrees apart.

Question Number. 55. The rotor of an Question Number. 59. Torque synchro
autosyn position indicating system is. systems are normally used when the.
Option A. a permanent magnet. Option A. system accuracy is of extreme
Option B. spring controlled. importance.
Option C. an electromagnet. Option B. mechanical load is high.
Correct Answer is. an electromagnet. Option C. mechanical load is low.
Explanation. The rotor of an autosyn position Correct Answer is. mechanical load is low.
indicating system is an electromagnet. Explanation. A torque synchro is only used for
indication - i.e. the load is low.

Question Number. 56. The rotor of a

magnesyn transmitter is. Question Number. 60. What device
Option A. a permanent magnet. transfers one energy type to another?.
Option B. an ac electromagnet. Option A. Transponder.
Option C. a dc electromagnet. Option B. Transducer.
Correct Answer is. a permanent magnet. Option C. Transmitter.
Explanation. The rotor of a magnesyn Correct Answer is. Transducer.
transmitter (and receiver) is a permanent magnet. Explanation. The device that transfers one
energy type to another is called a transducer.
Aircraft Electricity and Electronics 5th Edition
Eismin Page 171.
Question Number. 57. Torque synchro
systems are normally used when the.
Option A. system accuracy is of extreme Question Number. 61. Electrical power is
Page

importance. supplied to a synchro rotor.

DOWNLOAD OUR MOBILE APP FROM PLAY STORE @DGCA QUESTION PAPERS
IF YOU HAVE PREVIOUS SESSION QUESTION PAPERS, SHARE WITH US AT [email protected]
 WWW.EASAQUESTIONPAPERS.BLOGSPOT.COM PART -66 MODULE 4 PART -3

Visit to download all latest EASA / DGCA CAR 66 Module examination Question papers and study material

Option A. through slip rings. Question Number. 65. A control surface

Option B. through a commutator. position feedback signal is.
11(www.dgcaquestionpapers.in), Like us on Facebook @ fb/DGCAQuestionPapers ( All CAR 66 Module Exam QP Available

Option C. directly. Option A. inversely proportional to surface

Correct Answer is. through slip rings. position.
Explanation. Electrical power is connected to a Option B. proportional to surface position.
synchro rotor through slip rings.
Option C. non-linear.
Correct Answer is. proportional to surface
Question Number. 62. In a synchro position.
resolver, the stator coils are at what angle in Explanation. Position feedback is proportional
relation to one another?. to surface position. Meaning, as control surface
Option A. 45 degrees. deflection increases, so does the feedback.
Option B. 80 degrees.
Option C. 90 degrees.
Correct Answer is. 90 degrees.
Explanation. In a synchro resolver the stator Question Number. 66. A position gyro will
coils are 90 degrees to each other." provide.
Option A. acceleration feedback.
Option B. velocity feedback.
Question Number. 63. An increase in Option C. positional feedback.
negative feedback to the servo amplifier. Correct Answer is. positional feedback.
Explanation. Referring to a 'position gyro' as in
Option A. has no effect. artificial horizon and directional gyro.
Option B. increases amplifier stability.
Option C. decreases amplifier stability.
Correct Answer is. increases amplifier Question Number. 67. In velocity
stability. feedback the signal is.
Explanation. Negative feedback helps to Option A. out of phase.
increase the stability of an amplifier with changes Option B. in phase.
in temperature and the effects of age. Option C. equal to the error signal.
Correct Answer is. out of phase.
Explanation. The velocity feedback must be
Question Number. 64. In a synchro, what anti-phase with the error signal in order to oppose
is used to convert signals from one form to it (and thus be negative feedback).
another?.
Option A. Transducer.
Option B. Transmitter. Question Number. 68. If velocity
Option C. Transformer. feedback in a servo system is above optimum, this
Correct Answer is. Transducer. will cause.
Explanation. A 'transducer' converts one signal Option A. no effect.
type to another. Aircraft Electricity and Electronics Option B. sluggish operation.
5th Edition Eismin Page 171. Option C. hunting.
Correct Answer is. sluggish operation.
Page

DOWNLOAD OUR MOBILE APP FROM PLAY STORE @DGCA QUESTION PAPERS
IF YOU HAVE PREVIOUS SESSION QUESTION PAPERS, SHARE WITH US AT [email protected]
 WWW.EASAQUESTIONPAPERS.BLOGSPOT.COM PART -66 MODULE 4 PART -3

Visit to download all latest EASA / DGCA CAR 66 Module examination Question papers and study material

Explanation. Velocity feedback slows down the Explanation. A rate control system with a
operation of the rotor. steady input voltage will give a constant speed
12(www.dgcaquestionpapers.in), Like us on Facebook @ fb/DGCAQuestionPapers ( All CAR 66 Module Exam QP Available

output.

Question Number. 69. The amount of

rate feedback from a tachogenerator is. Question Number. 73. An increase in
Option A. proportional to speed. amplitude of a rate feedback signal will cause.
Option B. constant for all servo speeds.
Option C. inversely proportional to speed. Option A. sluggish servo operation.
Correct Answer is. proportional to speed. Option B. unstable operation.
Explanation. A tachogenerator provides Option C. reduced hunting.
feedback proportional to its rate (speed). Correct Answer is. reduced hunting.
Explanation. Rate feedback is to reduce
overshoot and oscillation (hunting), therefore,
increasing the amplitude (size) of the rate
Question Number. 70. What control feedback will decrease tendency to hunt.
system is used on an input that gives a controlled
predetermined output?.
Option A. Control Servo.
Option B. Closed Loop. Question Number. 74. An increase in
Option C. Open Loop. negative feedback.
Correct Answer is. Closed Loop. Option A. decreases system sensitivity.
Explanation. Only a closed loop control system Option B. increases system sensitivity.
can give a predetermined output. Option C. will make the driven device
continuously rotate.
Correct Answer is. decreases system
Question Number. 71. Increasing velocity sensitivity.
feedback from optimum will give. Explanation. Negative feedback (position
Option A. faster performance. and/or rate) increases stability but makes the
Option B. sluggish performance. servo unresponsive to small changes.
Option C. no change on the output.
Correct Answer is. sluggish performance.
Explanation. Velocity feedback is subtracted Question Number. 75. Position feedback
from the error signal to reduce the rate of the is used to.
output. Option A. indicate to the pilot the position of
the load.
Option B. to prevent control surface
Question Number. 72. A rate control oscillations while the surface is being moved.
servo system with a steady input voltage will give. Option C. ensure control surface moves to
the demanded position by the controls.
Option A. decreasing speed. Correct Answer is. ensure control surface
Option B. increasing speed. moves to the demanded position by the controls.
Option C. constant speed.
Page

Correct Answer is. constant speed.

DOWNLOAD OUR MOBILE APP FROM PLAY STORE @DGCA QUESTION PAPERS
IF YOU HAVE PREVIOUS SESSION QUESTION PAPERS, SHARE WITH US AT [email protected]
 WWW.EASAQUESTIONPAPERS.BLOGSPOT.COM PART -66 MODULE 4 PART -3

Visit to download all latest EASA / DGCA CAR 66 Module examination Question papers and study material

Explanation. Position feedback is to ensure Option C. Resolves a position into sine and
control surface moves to (and stops at) the cosine components.
13(www.dgcaquestionpapers.in), Like us on Facebook @ fb/DGCAQuestionPapers ( All CAR 66 Module Exam QP Available

demanded position by the controls. Correct Answer is. Resolves a position into
sine and cosine components.
Explanation. A resolver converts a position from
Question Number. 76. The output from a polar coordinates into cartesian coordinates,
control transformer is. and/or vice versa.
Option A. torque.
Option B. AC voltage.
Option C. DC voltage. Question Number. 80. If the feedback is
Correct Answer is. AC voltage. ideally damped, the signal will.
Explanation. The control transformer provides Option A. overshoots once and return back.
AC voltage in proportion to the error signal.
Option B. not overshoot.
Option C. oscillate.
Correct Answer is. overshoots once and
Question Number. 77. The stator output return back.
voltages from a synchro resolver are. Explanation. NIL.
Option A. 3 phase.
Option B. AC single phase.
Option C. DC. Question Number. 81. In a
Correct Answer is. AC single phase. tachogenerator the output voltage is.
Explanation. AC single phase from each Option A. inversely proportional to the
winding. speed.
Option B. zero.
Option C. directly proportional to the speed.
Question Number. 78. A typical use for
resolver synchros is. Correct Answer is. directly proportional to
Option A. fly by wire system. the speed.
Option B. engine power instrumentation. Explanation. NIL.
Option C. in compass comparator units.
Correct Answer is. in compass comparator
units. Question Number. 82. The primary
Explanation. A resolver synchro converts purpose of rate feedback in a positional servo
Cartesian coordinates (grid refs) to polar (compass system is to.
reading) and can be used to check the accuracy of Option A. ensure system linearity.
the compass system. Option B. prevent excessive overshoot.
Option C. ensure minimum response time.

Question Number. 79. What does a Correct Answer is. prevent excessive
resolver do?. overshoot.
Option A. Adds two signals. Explanation. NIL.
Option B. Resolves a movement into sine
Page

and cosine components.

DOWNLOAD OUR MOBILE APP FROM PLAY STORE @DGCA QUESTION PAPERS
IF YOU HAVE PREVIOUS SESSION QUESTION PAPERS, SHARE WITH US AT [email protected]
 WWW.EASAQUESTIONPAPERS.BLOGSPOT.COM PART -66 MODULE 4 PART -3

Visit to download all latest EASA / DGCA CAR 66 Module examination Question papers and study material

Question Number. 83. In a control Question Number. 87. In a Desynn

surface position indicating system the feedback indicator system, where is power supplied to?.
14(www.dgcaquestionpapers.in), Like us on Facebook @ fb/DGCAQuestionPapers ( All CAR 66 Module Exam QP Available

signal is.
Option A. in phase with the control surface Option A. Transmitter and indicator.
position. Option B. Indicator only.
Option B. indirectly proportional to the Option C. Transmitter only.
control surface position. Correct Answer is. Transmitter only.
Option C. proportional to the control surface Explanation. NIL.
position.
Correct Answer is. proportional to the control
surface position. Question Number. 88. What does the
Explanation. NIL. Desynn indicator rotor consist of?.
Option A. Electro magnet.
Option B. Permanent Magnet.
Question Number. 84. Synchro systems Option C. Aluminium cored coil.
depend on the principles of. Correct Answer is. Permanent Magnet.
Option A. electromagnetic induction. Explanation. NIL.
Option B. capacitive reaction.
Option C. mutual Inductance.
Correct Answer is. mutual Inductance.
Explanation. NIL.

Question Number. 85. A piezoelectric

crystal is an example of.
Option A. an analogue transducer.
Option B. a Pneumatic Transducer.
Option C. a Electro Acoustic Transducer.
Correct Answer is. an analogue transducer.

Explanation. NIL.

Question Number. 86. The difference

between an open and closed loop is.
Option A. error signal.
Option B. feedback.
Option C. correspondence.
Correct Answer is. feedback.
Explanation. NIL.
Page

DOWNLOAD OUR MOBILE APP FROM PLAY STORE @DGCA QUESTION PAPERS
IF YOU HAVE PREVIOUS SESSION QUESTION PAPERS, SHARE WITH US AT [email protected]