Meliadine Brine Project Description
Meliadine Brine Project Description
Meliadine Brine Project Description
PROJECT DESCRIPTION
Saline Effluent Discharge
into Marine Environment,
Rankin Inlet
DECEMBER 2017
VERSION 1
MELIADINE GOLD MINE PROJECT DESCRIPTION
TABLE OF CONTENT
TABLE OF CONTENT........................................................................................................................................ i
List of Figures................................................................................................................................................... ii
DECEMBER 2017 i
MELIADINE GOLD MINE PROJECT DESCRIPTION
LIST OF TABLES
Table 2: Salt Water Storage Capacity at the Mine for Groundwater and Water Primarily
Influenced by Underground Workings ................................................................................................. 10
Table 4: Current Volume of Water Stored at the Meliadine Mine on Surface .............................. 13
LIST OF FIGURES
Figure 2: Site Layout - Itivia Fuel Storage Facility and All Weather Access Road 4
DECEMBER 2017 ii
MELIADINE GOLD MINE PROJECT DESCRIPTION
The Mine Plan proposes mining methods for the development of the Tiriganiaq gold deposit, with
two open pits (Tiriganiaq Pit 1 and Tiriganiaq Pit 2) and one Underground Mine. Based on the
current Mine Plan, the Mine will produce approximately 12.1 million tonnes (Mt) of ore, 31.8 Mt of
waste rock, 7.4 Mt of overburden waste, and 12.1 Mt of tailings (Agnico Eagle 2017a). There are four
phases to the development of the Mine; just over 4 years of construction (Q4 2015 to 2019), 8 years
of Mine operation (2020 to 2027), 3 years of closure (2028 to 2030), and post-closure (2031
forwards).
Mining facilities in the Project Certificate (No. 006) and permitted Nunavut Water Board Type A
Water Licence (No. 2AM-MEL1631, 2016) include a plant site and accommodation buildings, three
ore stockpiles, a temporary overburden stockpile, a tailings storage facility, three waste rock storage
facilities, a water management system that includes containment ponds, water diversion channels,
retention dikes/berms, and a Water Treatment Plant. The general location and site layout of the
Mine are shown in Figure 1.
DECEMBER 2017 1
538000 538500 539000 539500 540000 540500 541000 541500
LEGEND
SERVICE ROAD
³
" HAUL ROAD
EMULSIONS G2 FRESHWATER INTAKE CAUSEWAY CATCHMENT BOUNDARY
PLANT "
NON CONTACT WATERBODY
TEMPORARY OVERBURDEN SEWAGE TREATMENT PLANT
STOCKPILE CONTACT WATERBODY
WATER COLLECTION POND
6990500
6990500
CHANNEL 2 DRAINED POND AREA
OPEN PIT
INDUSTRIAL SITE PAD
"
OVERBURDEN
LANDFARM
WASTE ROCK
" H7C MELIADINE WATER TREATMENT PLANT
H15G ORE
H15E H7B
ESKER WTP INTAKE CAUSEWAY
TAILINGS
"
M2 " H7A MELIADINE LAKE
H15D TREATED SEWAGE DISCHARGE
CP2 INDUSTRIAL SITE PAD
BER
6990000
H15
" ORE STOCKPILE 2
TAILINGS STORAGE " CP1
CHANNEL 1
Y:\burnaby\CAD-GIS\Client\Agnico_Eagle_Mines_Ltd\Meliadine_Gold_Project\99_PROJECTS\1773384\02_PRODUCTION\1000\MXD\Report\1773384_1000_1_Site_Layout_Meliadine_Mine_Site.mxd
FACILITY (TSF)
"
H14 " CULVERT 3
B7
CULVERT1
6989500
" "
"
CHANNEL 3 WASTE ROCK &
H4 H2 CULVERT 5
OVERBURDEN STORAGE H5
" "
H3 STUDY
FACILITY 2 (WRSF2) CHANNEL 6
CRUSHER LANDFILL AREA
D-CP1
BERM1 6 ^
CP
D- CP6 JETTY
CHANNEL8
"
CHANNEL7 P1 MELIADINE LAKE
" "
B6 WASTE ROCK &
CHANNEL4
OVERBURDEN STORAGE P-AREA CP6
FACILITY 1 (WRSF1)
H19
6989000
6989000
P2
"
4
CP
"
D-
"
B31 FACILITY 3 (WRSF3)
B32
CP5 JETTY
" A54
B33 A13
"
CP5
A12
CULVERT 6 REFERENCE
5
CP
6988500
6988500
BASE DATA OBTAINED FROM AGNICO EAGLE MINES LIMITED.
D-
"
DATUM: NAD 83 PROJECTION: UTM ZONE 15
BER M3
ANFO PLANT CHANNEL 5 TIRIGANIAQ PIT 2
A11
B5
(TIRI_1000_02)
B10 TIRIGANIAQ PIT 1
(TIRI_1000_01)
B33A J5
A10 250 0 250
J4
A40 A38 METRES
J3
J6
A9
AGNICO EAGLE MINES LIMITED
PROJECT
6988000
J2 TITLE
A37
A35 SITE LAYOUT
B22 B34 A8 J7 MELIADINE MINE SITE
PROJECT NO. 1773384 FILE No.
DESIGN CLT 8 Dec. 2017 SCALE AS SHOWN REV. 0
GIS CDB 8 Dec. 2017
CHECK JR 8 Dec. 2017 FIGURE: 1
538000 538500 539000 539500 540000 540500 541000 541500 REVIEW LY 8 Dec. 2017
MELIADINE GOLD MINE PROJECT DESCRIPTION
Tiriganiaq Underground Mine is planned to extend to approximately 625 m below the ground
surface and therefore, part of the Underground Mine will operate below the base of the continuous
permafrost. The underground excavations will act as a sink for groundwater flow during operation,
with water induced to flow through the bedrock to the Underground Mine workings once the Mine
has advanced below the base of the permafrost.
Based on the anticipated flows of groundwater reporting to the underground workings, a short-term
and long-term groundwater strategy is required. Groundwater inflow to the Underground Mine will
range between 300 cubic metres (m3)/day in 2018 to 420 m3/day in 2023 and 2024 (see Section 3.1).
Currently there is also with additional groundwater stored on surface in saline water storage ponds
that has been influenced by rock from the underground workings in the short-term (expected to be
up to 800 m3/day). During the Type A Water Licensing process in 2015, Agnico Eagle considered
several options presented in Appendix F of the Water Management Plan (Agnico Eagle 2015a) and
since that time has continued to investigate alternative options.
The preferred alternative is to treat the groundwater reporting from the underground workings and
discharge to Meliadine Lake in accordance with the Type A Water Licence 2AM-MEL1631 through
Collection Pond 1 (CP1). However, based on the potential volumes of groundwater, it is anticipated
that a second discharge location will be required. Agnico Eagle is proposing to treat groundwater
and discharge it as saline effluent to the ocean either as a direct discharge and/or after temporary
on-site storage in one or more of the water containment ponds at the Mine. Ocean discharge
currently not permitted and requires appropriate licenses and approvals.
For the ocean discharge option, the saline effluent would be trucked from the Mine and discharged
in Melvin Bay at Itivia Harbour – the Itivia Oil Handling Facility and all-weather access road (AWAR)
are presented in Figure 2. The discharge facility will include a saline water storage tank at the Itivia
Fuel Storage Facility and a pipeline extending to an engineered diffuser located in Melvin Bay during
the open water season from 2019 to 2032. The saline effluent will be discharged in a controlled
manner through the diffuser in compliance with the required discharge criteria to allow for
maximum dilution and minimum environmental impact to the marine environment.
Tiriganiaq Pit 1 and Tiriganiaq Pit 2 will be mined within the permafrost; therefore, groundwater
inflows to both open pits is expected to be negligible and were not considered as sources of
groundwater requiring treatment and discharge.
DECEMBER 2017 3
545500 546000 546500
LEGEND
GENERAL AREA FOR THE PROPOSED DIFFUSOR LOCATION
³
AIRPORT WATERCOURSE
AIRPORT TAKE-OFF RUNWAY
RANKIN INLET
VILLAGE WATERBODY
EXISTING
ELECTRICAL LINE
6964000
6964000
NEW 4160V POLE LINE (BY QEC)
LOCATION TO BE DETERMINED WITH QEC
OVERBURDEN MATERIAL
(TO CONFIM)
MILITARY CAMP
AIRPORT BYPASS
Y:\burnaby\CAD-GIS\Client\Agnico_Eagle_Mines_Ltd\Meliadine_Gold_Project\99_PROJECTS\1773384\02_PRODUCTION\1000\MXD\Report\1773384_1000_2_Site_Layout_Itivia_Harbour_AWAR.mxd
TANK #1
20 000 000 L.
TANK #2
13 500 000 L.
PUMPING STATION
PROTECTION
MANIFOLD POINT
ELECTRICAL
ANCHORAGE POINT 6963646.563N
ROOM ANCHORAGE POINT
6963645.119N 546131.323E
MARINE LINE 6963638.502N
545907.913E
Ø150mm 546328.785E
END OF MARINE LINE (APPROX. POSITION)
6963614.498N
FUTUR 546137.956E
Permanent Camp SALT WATER TANK
"
8 Exploration Camp
Mine Infrastructure " 116
8 FUEL TANK FARM
Area
HIGHER HIGH WATER LARGE TIDE (HHWLT)
COASTLINE REF. CANADIAN HYDROGRAPHIC
SERVICE (V-5628)
6963500
LICENCE "A"
LIMITE OF WORK (31m) (HHWLT)
RANKIN INLET
COMMERCIAL JETTY
All-weather
REFERENCE
MELVIN BAY
Access Road
BASE DATA OBTAINED FROM AGNICO EAGLE MINES LIMITED.
DATUM: NAD 83 PROJECTION: UTM ZONE 15
100 0 100
METRES
6963000
METRES GIS CDB 8 Dec. 2017
CHECK JR 8 Dec. 2017 FIGURE: 2
545500 546000 546500 REVIEW LY 8 Dec. 2017
MELIADINE GOLD MINE PROJECT DESCRIPTION
The following documents have been provided as part of the NPC Application to the Project and will
be adhered to for activities required to complete the Project:
While these plans have been provided as part of the NPC application, Agnico Eagle is committed to
adhering to all other existing plans that have been developed for the Meliadine Mine.
DECEMBER 2017 5
MELIADINE GOLD MINE PROJECT DESCRIPTION
Dependent on the groundwater inflow volume, the following options were considered for the long-
term management of groundwater inflows to the Underground Mine:
• treat saline groundwater and store/use the brine from the treatment process on-site
(Section 2.2)
• mix underground with surface contact water prior to release to the receiving environment in
Meliadine Lake (Section 2.3)
• ocean disposal (see Section 3, Ocean Disposal Project Description)
Based on the Type A Water Licence 2AM-MEL1631 Terms and Conditions, Part E: Conditions
Applying to Water Use and Management, No. 14, Agnico Eagle has reviewed the Project alternatives
to apply to the Groundwater Management Plan. Condition No. 14 specifically states:
“The Licensee shall submit a Groundwater Management Plan to the Board for approval in
writing, at least six (6) months prior to the discharge of any Groundwater. The Plan shall take
into consideration all comments raised and commitments made with respect to submissions
received during the technical review of the Application as well as final submissions and issues
raised during the Public Hearing Process, where applicable.”
The alternatives are discussed below.
Groundwater inputs to surface storage alone for management are expected to range approximately
from a minimum of 0.11 Mm3/year to a maximum of 0.18 Mm3/year, dependent on year of Mine life
(Agnico Eagle 2017a). Evaporators are in-use on site since mid-2017 at P1 to reduce groundwater
volumes stored in surface water ponds. A single evaporator is estimated to remove approximately
500 m3/day when operated for 24 hours with ideal wind and relative humidity conditions. While
DECEMBER 2017 6
MELIADINE GOLD MINE PROJECT DESCRIPTION
evaporators have been used with some success the combined volumes of groundwater with
anticipated surface water volumes influenced by underground rock to be managed is greater than
the available long-term storage at the Mine, and therefore, discharge to environment is required.
Short-term storage and treatment options are being implemented at the Mine pending regulatory
approvals for the long-term groundwater management option.
Hatch (2013) investigated groundwater treatment options for the site and concluded that a
combination chemical reverse osmosis and mechanical vapour compression evaporator plant would
be the most efficient method of treating excess groundwater for discharge. Agnico Eagle has also
undertaken a pilot test of a SaltMaker combined with a Chemical-Reverse Osmosis (RO) post-
treatment system.
The groundwater will flow through a Salt Water Treatment Plant (SWTP), comprised of a set of
SaltMakers, and will be treated to remove excessive total suspended solids (TSS), calcium chloride
(CaCl2), sodium chloride (NaCl), metals, phosphorous (P), and nitrogen compounds. The salt
generated by the water treatment unit will be stored on-site at the Mine, where it will be re-used
for underground operations and/or disposed of at an appropriate disposal location. Given the
predicted groundwater volumes, a maximum of three SaltMakers are proposed to be built at the
Mine, forming the SWTP, to treat the groundwater for discharge. Each SaltMaker has the capacity to
treat water at a flow rate of 120 m3/day, and a set of three SaltMakers for the SWTP will meet the
discharge volumes predicted (totalling 400 m3/day capacity), though temporary storage on site is
required during peak underground operations where the predicted flow may be up to 420 m3/day.
The first SaltMaker is planned to be commissioned in Q3-2018 and the second and third SaltMakers
will be built in Q1-2019 to meet increasing groundwater inflow needs. The need for a third SWTP
will be determined based on the capacity of the Mine for surface and underground storage.
The expected saline effluent temperature from the SWTP is expected to be approximately 35°C, with
an approximate pH of 7.5 (Saltworks 2017). The SWTP saline effluent largely meets the required
Water Quality Output requirements defined in Agnico Eagle’s Desalination Water Treatment Plan
Design Criteria and passes toxicity tests (Saltworks 2017). Saline effluent quality (of the
groundwater) after treatment through the SWTP indicates that total dissolved solids (TDS) would be
approximately 158 mg/L (condensed water after treatment; Saltworks 2017).
DECEMBER 2017 7
MELIADINE GOLD MINE PROJECT DESCRIPTION
Post-treatment options, such as the RO post-treatment system, are being considered if required, to
meet applicable effluent quality criteria for Meliadine Lake. The permeate resultant from Chemical-
Reverse Osmosis (RO) post-treatment system meets all the required site-specific Water Quality
Objectives and passes all toxicity tests. Saline effluent quality after treatment through the SWTP
indicates that TDS concentration would be considerably reduced, at approximately 55 mg/L after RO
post-treatment (Saltworks 2017). Pilot testing of the SaltMaker condensed water and RO permeate
quality results are presented in the SaltMaker Pilot Final Report document (Saltworks 2017). The
results indicate that values will meet site-specific water quality objectives for water management,
which also comply with MMER.
Mine effluent discharge is permitted under the Type A Water Licence 2AM-MEL1631. It is the
preferred option if the conditions of the Type A Water Licence 2AM-MEL1631 can be met. The
option to discharge saline effluent from the Saltmaker to Meliadine Lake will be described and
submitted to the Nunavut Water Board in the Groundwater Management Plan and approval will be
required, prior to discharge, as per the Term and Condition Part E, No. 14 of the Type A Water
Licence 2AM-MEL1631.
DECEMBER 2017 8
MELIADINE GOLD MINE PROJECT DESCRIPTION
Pending necessary permits and/or authorizations, Agnico Eagle proposes to directly discharge saline
effluent into Melvin Bay at Itivia Harbour or treat the underground saline water to meet discharge
water quality criteria for Melvin Bay. Agnico Eagle anticipates that treatment for metals and
potentially TDS may be required. However it is expected that groundwater stored at surface at the
Mine will be influenced by surface water inputs (e.g., by precipitation). Temporary storage of
groundwater (treated through the underground TSS removal plant) may occur, dependent on
volumes.
Saline effluent will be trucked to the discharge facility at the Itivia Fuel Storage Facility for discharge
during the open water season (May to October). The discharge facility, located at the Itivia Fuel
Storage Facility, will include a saline water storage tank and a pipeline extending to an engineered
diffuser located in Melvin Bay. The treated groundwater (saline effluent) will be discharged
seasonally in a controlled manner through the diffuser to allow for maximum dilution and minimum
impact on the marine environment. At closure, any treated groundwater stored on surface at the
Mine would be returned underground. The discharge conveyance system is described further in
Section 3.6.Saline effluent quality will be required to meet the Canadian federal end-of-pipe
discharge criteria (Metal Mining Effluent Regulations – or MMER), including the amended MMER
(GC 2017; anticipated to come into effect in 2018), and Canadian Surface Water Quality Guidelines
(Canadian Council of Ministers of the Environment Guidelines for the Protection of Aquatic Life
[CCME 2003]) or Site-Specific Water Quality Objectives at the edge of the mixing zone for the
diffuser discharge into Melvin Bay. It is recognized that further discussions are required with
relevant stakeholders to confirm that this approach meets the amended MMER (GC 2017).
The Groundwater Management Plan will be update to take into account the change in operation
and technologies associated with Ocean disposal and submitted to regulators prior to any discharge.
The submission, review, and approval of a Groundwater Management Plan is a requirement of the
current Type A Water Licence 2AM-MEL1631 (Part E, Item 14). It is also recognized that further
regulatory direction regarding ocean disposal may be provided by the Nunavut Planning Commission
and Nunavut Impact Review Board.
DECEMBER 2017 9
MELIADINE GOLD MINE PROJECT DESCRIPTION
The groundwater inflow predictions presented in Table 1 do not account for grouting currently being
conducted as a mitigation to reduce groundwater inflows to the underground development, or
potential losses through the ventilation system. Both mechanisms will potentially reduce actual
groundwater inflows to the Mine relative to what was predicted. As such, these predicted inflows to
the Underground Mine development represent unmitigated estimates and can be considered as
conservative. Groundwater inflows to the Mine since 2015 have not been discharged to the
environment and are being stored underground, in the Saline Pond, in the P-Area or actively
evaporated during the open water season (Agnico Eagle 2017a).
Excess groundwater will not be managed underground, and will be pumped for direct discharge
and/or storage on the surface at the Mine in the Saline Pond, the P-area ponds, and Collection
Pond 5 (CP5). The pond capacities and maximum water elevation are presented in Table 2. As
indicated in Section 2.2, groundwater inputs to surface storage for management are expected to
range approximately from a minimum of 0.11 Mm3/year to a maximum of 0.18 Mm3/year,
dependent on year of Mine life (Agnico Eagle 2017a).
Table 2: Salt Water Storage Capacity at the Mine for Groundwater and Water Primarily
Influenced by Underground Workings
DECEMBER 2017 10
MELIADINE GOLD MINE PROJECT DESCRIPTION
Where water, influenced by the underground workings, and groundwater is stored at the Mine, it
will be influenced by non-contact surface water, such as precipitation. Non-contact groundwater
(treated via the underground TSS removal plant) pumped from underground for direct discharge
with the groundwater stored on site will combine in the storage tank at the the Itivia Fuel Storage
Facility prior to disposal via the diffuser to the ocean – as such, TDS values as well as other
parameters are anticipated to be reduced sufficiently to meet applicable discharge criteria at the
edge of the mixing zone and MMER requirements.
DECEMBER 2017 11
MELIADINE GOLD MINE PROJECT DESCRIPTION
DECEMBER 2017 12
MELIADINE GOLD MINE PROJECT DESCRIPTION
It is expected that in the short-term a greater volume of water will be required to discharge to the
ocean due to the current volume (Table 4) of water being stored at the Mine and the seasonality of
the discharge. It is also anticipated that in wet years the volume of water requiring discharge may be
greater than in dry years.
DECEMBER 2017 13
MELIADINE GOLD MINE PROJECT DESCRIPTION
At a volume of 800 m3/day for saline effluent discharge, the same transportation details apply,
however, additional trucks will be required to meet the additional volume to be discharged. Four
water trucks will be required, each with one individual to operate during the open water season
(May to October) from 2019 to 2032. A fifth truck will be available in case of mechanical
malfunction. Agnico Eagle is currently investigating the appropriate volume for marine discharge
(Section 3.4).
DECEMBER 2017 14
MELIADINE GOLD MINE PROJECT DESCRIPTION
All trucks will be fueled using diesel facilities located on-site (Golder 2015), shown as Table 6. No
additional fuel storage is required above that permitted under the Type A Water Licence 2AM-
MEL1631.
Fuel
Location Facility Maximum Amount by Unit
Product
Itivia Fuel Storage Facility 20 ML tank
Itivia Fuel Storage Facility Itivia Fuel Storage Facility 13.5 ML tank
Diesel Itivia Fuel Storage Facility 4 ML tank
Site Main Fuel Tank 3 ML
Portal #1 Mine Site Tank Farm
Site Fuel Tank summer 250,000 L/tank
Source: Type A Water Licence 2AM-MEL1631, NWB 2016.
Currently, there are no specific criteria for mixing zone discharges in Canadian coastal and estuarine
water for mine effluent. However the Guidelines for the Discharge of Treated Municipal Wastewater
in the Northwest Territories (NWT 1992) provide guidance that the limits of initial mixing zone in
marine environments is 100 m from all points of discharge. A radius of 100 m from the point of
discharge is widely used for marine environmental compliance assessments. There are also no
federal guidelines available for chloride or thermal discharges to the marine environment, but the
British Columbia Ministry of the Environment Guidelines (2017) state the following:
• “Human activities should not cause the chloride of marine and estuarine waters to fluctuate
by more than 10% of the natural chloride expected at that time and depth.”
• Temperature at the mixing zone boundary should not change by more or less than 1°C from
natural ambient background temperatures, and the hourly rate of change should not exceed
0.5°C.
Based on the bathymetry of Melvin Bay at Itivia Harbour, the diffuser is best placed at greater depth
to provide the best possible mixing. A rocky outcrop is located near the Itivia Harbour spud barge
location to the south-east of the proposed receiving tank location (see Figure 2). Military facilities
DECEMBER 2017 15
MELIADINE GOLD MINE PROJECT DESCRIPTION
are located to the north-west of the Itivia Oil Handling Facility, including buildings and a by-pass
road; vehicles cannot stop within 500 m of these military facilities.
In consideration of the existing facilities and the bathymetry of Melvin Bay, the proposed location
for the diffuser pipe is to extend it from the receiving tank directly south-south-west into Melvin Bay
(see Figure 2). The port would be placed on the seabed at a depth of approximately 20 m, to ensure
an unconstrained mixing zone and to avoid interference with use of Itivia Harbour by ships and
boats at high and low tide.
The discharge pipe is anticipated to be a 3 or 4 inch diameter pipe, placed inside a larger insulating
pipe. The pipe is anticipated to be a high-density polyethylene (HDPE) pipe and to have an outfall
length of 260 to 345 m with a single or double port for discharge, depending on the required
dilution factor to meet the required discharge criteria. The port is proposed to be an approximately
2 inch diameter HDPE pipe, placed at a vertical angle of 45° from the horizontal plane (upward) at
the seabed. Agnico Eagle is currently investigating appropriate diffuser designs for the proposed
discharge, and these will be provided, if the Project is approved, 60 to 90 days prior to construction.
1Information provided regarding the engineering of the discharge pipe has been completed for assessment purposes only and should not
be considered final design.
DECEMBER 2017 16
MELIADINE GOLD MINE PROJECT DESCRIPTION
SECTION 4 • CONCLUSION
This document provides an overview and information on the proposed activities and facilities
required to discharge groundwater and water influenced by underground to the marine
environment at Melvin Bay, as well as an overview of other alternatives considered.
Agnico Eagle is considering treatment options to meet discharge criteria, in compliance with
applicable discharge criteria and/or site specific water quality objectives, as required. Activities and
facilities described herein are for planning purposes only and should not be considered final design.
Agnico Eagle is committed to responsibly managing water resources to minimize or eliminate
potential effects on the local aquatic ecosystem in accordance with the Nunavut Impact Review
Board Project Certificate (NIRB Project Certificate [No. 006], 2015), the Nunavut Water Board Type A
Water Licence (No. 2AM-MEL1631, 2016) and the objectives as outlined in the Water Management
Plan (Agnico Eagle 2017a).
DECEMBER 2017 17
MELIADINE GOLD MINE PROJECT DESCRIPTION
SECTION 5 • REFERENCES
Agnico Eagle. 2014. Final Environmental Impact Statement (FEIS) - Meliadine Gold Project, Nunavut
from: ftp://ftp.nirb.ca/02-REVIEWS/ACTIVE%20REVIEWS/11MN034-Agnico
Eagle%20MELIADINE/2-REVIEW/09-FINAL%20EIS/FEIS Accessed on November, 2014.
Agnico Eagle. 2015a. Meliadine Gold Project, Type A Water Licence. Water Management Plan.
Version 1. Submitted to the Nunavut Water Board. April 2015.
Agnico Eagle. 2017a. Meliadine Gold Project Water Management Plan. Version 3. 6513-MPS-11.
March 2017.
Agnico Eagle. 2017b. Meliadine Gold Project, Mine Waste Management Plan. Version 3. 6513-MPS-
09. March 2017.
Agnico Eagle. 2017c. Meliadine Gold Project, Roads Management Plan. Version 5. 6513-MPS-05.
March 2017.
Agnico Eagle. 2017d. Meliadine Gold Project, Spill Contingency Plan. Version 6. 6513-MPS-05. March
2017.
Agnico Eagle. 2017e. Meliadine Gold Project, Shipping Management Plan. Version 6. March 2017.
British Columbia Ministry of the Environment. 2017. Approved Water Quality Guidelines: Aquatic
Life, Wildlife & Agriculture.
CCME (Canadian Council of Ministers of the Environment). 2003. Canadian Environmental Quality
Guidelines – Water Quality Guidelines for the Protection of Aquatic Life.
Golder (Golder Associates Ltd.). 2014a. SD 6-4 Terrestrial Environment Management and Monitoring
Plan – Meliadine Gold Project, Nunavut. Doc 300-1314280007 Ver 0. April 2014.
Golder. 2014b. SD 5-1 Air Quality monitoring Plan – Meliadine Gold Project, Nunavut. Doc 375-
1314280007 Ver 0. April 2014.
Golder. 2014c. SD 9-1 Cultural and Heritage Resources Protection Plan – Meliadine Gold Project,
Nunavut. Doc 367-1314280007 Ver 0. April 2014.
GC (Government of Canada). 2017. Regulations Amending the Metal Mining Effluent Regulations
(MMER). Canada Gazette Part I, Vol 151, No. 19. May 2017
DECEMBER 2017 18
MELIADINE GOLD MINE PROJECT DESCRIPTION
Hatch. 2013. Agnico Eagle Mines Ltd. - Meliadine Desalination Study - Salt Water Treatment Plant
Report. Report No. H350003-000-05-124-002/6505-SSR-01_R82, Rev 2. September 30, 2013.
NIRB (Nunavut Impact Review Board). 2015. Project Certificate for Agnico-Eagle Mines Ltd.’s
Meliadine Gold Mine Project (NIRB Project Certificate No.006).
NWB (Nunavut Water Board). 2016. Water Licence No. 2AM-MEL1631 for Agnico-Eagle Mines Ltd.’s
Meliadine Gold Project.
NWT (Northwest Territories). 1992. Guidelines for the Discharge of Treated Municipal Wastewater
in the Northwest Territories.
Saltworks (Saltworks Technologies Inc.). 2017. Agnico Eagle SaltMaker Pilot Final Report. April 2017.
DECEMBER 2017 19