Arl 200s

Download as pdf or txt
Download as pdf or txt
You are on page 1of 12

ARL-200S

LIFT CONTROLLER

USER MANUAL
ARKEL Elektrik Elektronik Ltd. Şti. www.arkel.com.tr

Publisher ARKEL Elektrik Elektronik Ticaret Ltd. Şti.


Bostanci Yolu Cad. Sehit Sok. No:36
Yukari Dudullu Istanbul TURKIYE

TEL: (+90 216) 540 03 10 – 11 - 12

Fax: (+90 216) 540 03 09


E-mail : info@arkel.com.tr
www.arkel.com.tr

Date of issue 2009

Document version V1.5

Hardware version V2.3

Software version V3.3

ARL-200S
ARKEL 2009 2
ARKEL Elektrik Elektronik Ltd. Şti. www.arkel.com.tr

CONTENTS
 
1. ENTERING THE PROGRAM MENU ..................................................................................................................... 4 
1.1 MANUAL MOVEMENT MODE....................................................................................................................... 4 
1.2 GIVING CALLS BY KEYPAD ......................................................................................................................... 4 
1.3 PROGRAM PARAMETERS .............................................................................................................................. 4 
2. LIST OF PARAMETERS .......................................................................................................................................... 5 
2.1 COMMAND TYPE ............................................................................................................................................ 5 
2.2 NUBER OF FLOORS ......................................................................................................................................... 5 
2.3 CAR CONNECTION.......................................................................................................................................... 5 
2.4 AUTOMATIC DOOR......................................................................................................................................... 5 
2.5 AUTOMATIC DOOR AT FLOOR .................................................................................................................... 5 
2.6 CAR LAMP DELAY .......................................................................................................................................... 6 
2.7 WAIT AT FLOOR .............................................................................................................................................. 6 
2.8 PARKING FLOOR ............................................................................................................................................. 6 
2.9 PARKING DELAY ............................................................................................................................................ 6 
2.10 R. CAM DELAY .............................................................................................................................................. 6 
2.11 MAX HIGH SPEED ......................................................................................................................................... 6 
2.12 MAX LOW SPEED .......................................................................................................................................... 6 
2.13 POSITION RESET ........................................................................................................................................... 6 
2.14 CONTACTOR DELAY .................................................................................................................................... 6 
2.15 RESERVE ......................................................................................................................................................... 6 
2.16 CARE TIME ..................................................................................................................................................... 6 
2.17 END OF CARE TIME ...................................................................................................................................... 7 
2.18 PASSWORD ..................................................................................................................................................... 7 
2.19 DIGITAL SETUP ............................................................................................................................................. 7 
2.20 LIMITS AT INSP. ............................................................................................................................................ 7 
2.21 SELECTOR TYPE............................................................................................................................................ 7 
2.22 GROUP FUNCTION ........................................................................................................................................ 7 
2.23 DOOR OPEN ERROR ...................................................................................................................................... 7 
2.24 EXIT MENU ..................................................................................................................................................... 7 
3. ARL-200S ERROR CODE......................................................................................................................................... 8 
4. DIMENSIONS OF ARL-200 CONTROLLER .......................................................................................................... 9 

ARL-200S
ARKEL 2009 3
ARKEL Elektrik Elektronik Ltd. Şti. www.arkel.com.tr

1. ENTERING THE PROGRAM MENU

Figure 1 : ARL-200S Control Card

Press the LEFT button for 3 seconds. If no password has been entered before (0000 : factory
default), the first parameter “COMMAND TYPE” is displayed on LCD . If a password has been
assigned before, you must enter the four digit password by pressing the UP and DOWN buttons.
Then press the RIGHT button.The first parameter is displayed.If the password is entered incorrect
an error massage “WRONG PASSWORD” will appear on the LCD.If the password is entered
incorrect for three times, the system gets blocked off. Six digits PUK CODE must be entered.

1.1 MANUAL MOVEMENT MODE

Press the RIGHT button for 3 seconds. “MANUAL MOVEMENT” message is displayed.You can
move the lift up and down by pressing UP and DOWN buttons. Press the LEFT button to leave the
MM Mode.

1.2 GIVING CALLS BY KEYPAD

It is possible to give any call by using keypad. Press UP button to set a call to top floor and press
DOWN button to set a call to bottom floor on main screen.

1.3 PROGRAM PARAMETERS

You can pass through the parameters by pressing LEFT and RIGHT buttons and change the
parameter by pressing UP and DOWN buttons. When you change a parameter by pressing UP and
DOWN buttons, the new value for that parameter is recorded in the temporary memory. It is not
necesarry to press any key to record any changed parameter. All parameters are recorded to the
memory after leaving the program menu. If card’s power cut out and turned on again before
leaving the program menu, the parameters keep the older values.

ARL-200S
ARKEL 2009 4
ARKEL Elektrik Elektronik Ltd. Şti. www.arkel.com.tr

2. LIST OF PARAMETERS

2.1 COMMAND TYPE


You can choose the command type.

- Universal command (Only one call is accepted)


- Parallel command (Car calls and floor calls connect to the same terminal)
- Down Collective (Car will stop for only down direction calls)
- Up Collective (Car will stop for only up direction calls)
- Collective-Selective (There are call buttons for each direction)

2.2 NUBER OF FLOORS


You can adjust the number of floors from 2 to 16.

2.3 CAR CONNECTION

- SERIAL
FX_MB has an ability to communicate with a control card (FX_SERI) on the car via two cables
(S1A&S1B), when used some of the controls (Car calls ,7 Segment Display, Full Load , Over Load
. etc) are not connected from the car to the control panel..

-PARALLEL
All signals from the car to the panel are connected seperatly.
There is no need to use special cable or shielded cable for serial communication.

But it will be better if the first or last two of the flexible cable are used for S1A, S1B and high
voltages should be at the other side (far from S1A, S1B) of the flexible cable. If a communication
error occures, red error led on the FX_SERI control card will blink.

2.4 AUTOMATIC DOOR


If an automatic door is used, you can choose type of it.

- Not Automatic : There is no automatic door.


- Semi automatic : There is only an automatic car door.
- Full Automatic : Car and floor doors are automatic.

2.5 AUTOMATIC DOOR AT FLOOR


Automatic door position when lift waits for calls.

- Waits closed
- Waits opened

WARNING!!! Waits open is not allowed according the harmonized standard EN 81-1/2. So this
parameter must be set to “Waits closed” to fully fit EN81-1/2. The lifts at the countries which has
own standard other then EN81-2/2 or at the lifts that modernized and taken measures against risk of
doors waiting open can be set as “waits opened”.

ARL-200S
ARKEL 2009 5
ARKEL Elektrik Elektronik Ltd. Şti. www.arkel.com.tr

2.6 CAR LAMP DELAY


You can adjust the car lamp delay in seconds.

2.7 WAIT AT FLOOR


When going between calls the lift waits for passangers to get in and get out for a time which is
adjusted with this parameter (It is in seconds).

If the serial communication board is used on inspection box and the OPEN/CLOSE button
signals are connected to serial communication board, increase this parameter and adjust the time
delay trimpot to zero on automatic door board. If car installation is parallel and door is full
automatic, set this parameter to 2 s and adjust the time delay trimpot to zero on automatic door
board.

2.8 PARKING FLOOR


It is possible to send the lift to a specific floor after finishing its job.

2.9 PARKING DELAY


The lift waits for a time before going to the parking floor after finishing its job.

2.10 R. CAM DELAY


After energising the R. Cam it waits for the door lock. If it is not locked for the time that is adjusted
by this parameter, control panel gives error and goes out of service (It is in seconds).
Set this parameter to 35 s for semi-automatic doors and 95 s for full automatic doors.

2.11 MAX HIGH SPEED


Maximum time to reach a new floor at high speed.(In seconds).

2.12 MAX LOW SPEED


Maximum time to reach the floor level after passing to low speed (In seconds).

2.13 POSITION RESET


Althoug the control panel remembers the last position at any mains power failure, sometimes (for
instant an emergency rescue system with batteries may be exist ) when mains power is live the user
may wish to reset the position.

2.14 CONTACTOR DELAY


The time to keep the RP contactor switch on after the movement ends can be adjusted by this
parameter.
Disable this parameter for single speed and two speed lift systems.

2.15 RESERVE
ARL-200S does not use this parameter at this time.

2.16 CARE TIME


This parameter decreases everyday. When it is 0 the END OF CARE TIME parameter will be
prossesed.

ARL-200S
ARKEL 2009 6
ARKEL Elektrik Elektronik Ltd. Şti. www.arkel.com.tr

2.17 END OF CARE TIME


When the CARE TIME parameter reaches 0 following occurs.

- CONTINUE OPARETE: Lift continue to do its job.


- STOP : Lift stops and waits for check up.
- SIGNAL OFF : 31 , 32 ,12 , 02 , KL signals will be shutting.

2.18 PASSWORD
Password to enter program parameters.

2.19 DIGITAL SETUP


Press Up buton at this parameter to enter digital setups. Then you can change the blinking
paremeter by pressing up or down butons. Use left / right for selecting floor number and it’s
digital setup. The digital setup can be entered for each floor separately.

2.20 LIMITS AT INSP.


At Manuel Movement Mode this parameter adjusts if car stops immediately after reaching Up &
Down forced slow travel limits or continue untill to the floor levels.

- Direct Stop
- Go Floor level

Set this parameter to “GO FLOOR LEVEL” for systems with AKUS-SD evacuation unit.

2.21 SELECTOR TYPE


This parameter determines the counter system for floor detection

● NORMAL M1 COUNT : For single speed and two speed systems


● SPECIAL JF COUNT : For VVVF systems

2.22 GROUP FUNCTION


You can chose if the panel works as a SIMPLEX or DUBLEX panel.

2.23 DOOR OPEN ERROR


At the end of this time if the door is still open, the card gives an error. If there is
another lift (Dublex systems), the other one goes to calls.

Set this parameter to 240 s for full automatic doors.

2.24 EXIT MENU


When “EXIT MENU“ appears on lcd you can press this button to exit from menu. Don’t forget
your password. It will be asked to enter into the menu next time.

ARL-200S
ARKEL 2009 7
ARKEL Elektrik Elektronik Ltd. Şti. www.arkel.com.tr

3. ARL-200S ERROR CODE

CODE ERROR
H1 DOOR CAN NOT LOCKED ERROR
H2 CAN NOT REACH NEW FLOOR
H3 DOOR IS OPEN FOR A LONG TIME
H4 MAX LOW SPEED TIME OVERFLOW
H5 BOTH LIMITS ARE OPEN
H6 UP LIMIT OPEN WHILE GO DOWN
H7 DOWN LIMIT OPEN WHILE GO UP
H8 MOTOR PTC IS OPEN
H9 LIFT CARE TIME OVERFLOW
H10 CONTACTOR CHECKBACK ERROR
H11 -
H12 -
H13 -
H14 100 VOLTAGE UNDER LIMIT
H15 HIGH VOLTAGE.SHUTDOWN POWER

ARL-200S
ARKEL 2009 8
ARKEL Elektrik Elektronik Ltd. Şti. www.arkel.com.tr

4. DIMENSIONS OF ARL-200 CONTROLLER

Front View

Panel fitting hole

Keypad
160mm
170mm

LCD

Cover fitting screw

221mm

231mm

Sideway View

Cover fitting screw


Cover
Cover screw
28mm

20mm

Pcboard
Pcboard fitting screw
260mm

ARL-200S
ARKEL 2009 9
ARKEL Elektrik Elektronik Ltd. Şti. www.arkel.com.tr

ATTENTION!
Take care while connecting
your flexible cable

There are small points to take care while connecting your flexible cable. Arrange your cable order
according to their electrical signal level. Although the cables have enough insulation, long parallel
cables have transformer effect. The signals can joint between each neighbors. If there is two or
more flexible cables it is better to separate low an high voltage signals.

Here is an example of faulty connection.

Cable No: Signal Signal level


------------ --------------------------------------- ---------------
1 100 (24 Source) 24Vdc
2 A (Digital segment) 24Vdc
3 B (Digital segment) 24Vdc
… ... … …
10 817 (UP limit Switch) 48Vdc
11 818 (Down limit switch) 48Vdc
12 810 (Magnetic Cam Power-) 180Vdc
13 2001 (Magnetic Cam Power+) 180Vdc
14 804 (Over load) 24Vdc
15 401 (Car Call 1) 24Vdc
16 402 (Car Call 2) 24Vdc
… … ... …
20 406 (Car Call 6) 24Vdc
21 2 (Car Lamp) 220Vac
22 1 (Car Power source) 220Vac

In this example ever car lamp on/off operation makes high voltage peaks on line and it can leak to
406 (car call signal). In long term this cause a fault on 406 output transistor. Also there is risk
because of Magnetic cam power lines. 818 and 804 signal may have faulty operation in long term.

Here is an example of correct connection order.

100 , A , B , C , D , E , F , G, 804 , 805 , 401 , 402 , 403 .. , Î All 24V signals ,


1000 Î Small signal 0V ,
101, 817, 818, 869, 500, 501, 120…. Î All 48V signals ,
PE , N Î Ground , Line Neutral ,
810 , 2001 , 1 ,2 …. Î All high voltage signals

ARL-200S
ARKEL 2009 10
ARKEL Elektrik Elektronik Ltd. Şti. www.arkel.com.tr

Timing Warnings For ARL-200 Controller with ADrive


The main contactors (KPA and KPB) must drop after the mechanical brake contactor (KFR) drops when lift stops
at floor level. If these contactors drop at the same time, it means contactors drop unwillingly while motor is still
running. Increase the paramater value of CANTACTOR DELAY on ARL-200 parameter menu. It is sufficient that the
main contactors drop 0.5 second after the mechanical brake contactor drops. It is possible to increase this delay time
but opening door is delayed too.

ARL-200 controller must receive the information about ADrive fault and can stop the operation. Otherwise, in the
case of a faulire ARL-200 controller thinks that the motor is still running and after a delay time blocks the lift with the
fault “CAN NOT REACH NEW FLOOR”. The contact of ADrive error relay (RHO-RHA) must be connected properly
according to electrical diagrams. 120, 130 and 140 indicators on controller must be turned of when the RHO-RHA
teminals is unplugged.

ARL-200S
ARKEL 2009 11
ARKEL Elektrik Elektronik Ltd. Şti. www.arkel.com.tr

ARKEL Elektrik Elektronik Ticaret Ltd. Şti.


Bostancı Yolu Cad. Şehit Sok. No:36 Yukarı Dudullu İstanbul TURKIYE
TEL: (+90 216) 540 03 10 - 11 -12
Fax: (+90 216) 540 03 09
E-mail : info@arkel.com.tr
www.arkel.com.tr

ARL-200S
ARKEL 2009 12

You might also like