®

DataMan 260
Quick Reference Guide

10/9/2015
Version 5.6.0
 Legal Notices

Legal Notices
The software described in this document is furnished under license, and may be used or copied only in accordance with
the terms of such license and with the inclusion of the copyright notice shown on this page. Neither the software, this
document, nor any copies thereof may be provided to, or otherwise made available to, anyone other than the licensee.
Title to, and ownership of, this software remains with Cognex Corporation or its licensor. Cognex Corporation assumes
no responsibility for the use or reliability of its software on equipment that is not supplied by Cognex Corporation.
Cognex Corporation makes no warranties, either express or implied, regarding the described software, its
merchantability, non-infringement or its fitness for any particular purpose.
The information in this document is subject to change without notice and should not be construed as a commitment by
Cognex Corporation. Cognex Corporation is not responsible for any errors that may be present in either this document or
the associated software.
Companies, names, and data used in examples herein are fictitious unless otherwise noted. No part of this document
may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, nor
transferred to any other media or language without the written permission of Cognex Corporation.
Copyright © 2015. Cognex Corporation. All Rights Reserved.
Portions of the hardware and software provided by Cognex may be covered Cognex Corporation. All Rights Reserved.
by one or more U.S. and foreign patents, as well as pending U.S. and foreign patents listed on the Cognex web site at:
http://www.cognex.com/patents.

The following are registered trademarks of Cognex Corporation:

Cognex, 2DMAX, Advantage, Alignplus, Assemblyplus, Check it with Checker, Checker, Cognex Vision for Industry,
Cognex VSOC, CVL, DataMan, DisplayInspect, DVT, EasyBuilder, Hotbars, IDMax, In-Sight, Laser Killer, MVS-8000,
OmniView, PatFind, PatFlex, PatInspect, PatMax, PatQuick, SensorView, SmartView, SmartAdvisor, SmartLearn,
UltraLight, Vision Solutions, VisionPro, VisionView
The following are trademarks of Cognex Corporation:
The Cognex logo, 1DMax, 3D-Locate, 3DMax, BGAII, CheckPoint, Cognex VSoC, CVC-1000, FFD, iLearn, In-Sight
(design insignia with cross-hairs), In-Sight 2000, InspectEdge, Inspection Designer, MVS, NotchMax, OCRMax,
ProofRead, SmartSync, ProfilePlus, SmartDisplay, SmartSystem, SMD4, VisiFlex, Xpand, PowerGrid, Hotbars2
Other product and company trademarks identified herein are the trademarks of their respective owners.

2
 Table of Contents

Table of Contents
Legal Notices 2
Table of Contents 3
Symbols 4
Getting Started 5
About DataMan 260 5
DataMan 260 Accessories 6
DataMan 260 Systems 9
Communication Modules 10
Ethernet Interfaces 10
Reader Layout 11
Dimensions 15
Installing an Optical Filter 17
Installing a Liquid Lens 19
Changing from a 6.2 mm Lens to a 16 mm Lens 22
Changing to an Illumination with a Different Color 24
Setting Up Your DataMan 26
Mounting 26
Replacing a DataMan 362 with a DataMan 262 on the Factory Floor 27
I/O Cables 29
Acquisition Triggering 30
High-Speed Output Lines 31
High-Speed Output Wiring 32
Ethernet Cables 33
Installing the DataMan Software 34
Setting the Focus Position 35
Field of View and Reading Distances 37
External Triggering and Trigger Modes 42
Training and Trigger Modes 42
Training 42
Incremental Training for Multiple Symbologies 43
Tuning 44
Industrial Protocols 45
DataMan 260 Specifications 46
Imager Specifications 46
Illumination Options 47
Precautions 48
Regulations/Conformity 49

3
 Symbols

Symbols
The following symbols indicate safety precautions and supplemental information.

WARNING: This symbol indicates the presence of a hazard that could result in death, serious personal injury or
electrical shock.

CAUTION: This symbol indicates the presence of a hazard that could result in property damage.

Note: Notes provide supplemental information about a subject.

Tip: Tips provide helpful suggestions and shortcuts that may not otherwise be apparent.

4
 Getting Started

Getting Started
About DataMan 260

The DataMan 260 readers are best in class ID readers, offering superior performance with the latest ID tools, flexibility to
configure the reader in terms of lighting and optics to optimize the application, and an ease-of-use giving the user the
ability to setup and deploy an application quickly and efficiently all without the need for PC:

l Superior performance, 1-D and 2-D code reading, including HotBars2™ and patent-pending PowerGrid™
l Flexible optics/lighting, including field upgrades, allowing for the protection of your investment
l Ease-of-use, including an auto-tune and trigger button on the reader, the ability to configure the reader in a
straight or right-angle orientation and auto-focus capability utilizing a liquid lens

The DataMan 260 readers provide support for Ethernet and RS-232 communications.
Key highlights:

l 1DMax with HotBars2™, best in class 1-D reading, 2DMax with PowerGrid™, best in class 2-D reading. Reading
codes no other ID reader on the market can.
l Multiple options for LED lighting, along with optical filters and polarizing filters. Options for different powered lens,
with autofocus capabilities for each.
l Intelligent tuning and dynamic configuration of the reader combined to make the installation and setup of the
application a snap.

This document provides basic information about how to configure and use DataMan 260 readers. Additional information
is available through the Windows Start menu or the DataMan Setup Tool Help menu after you install the DataMan
software on your PC:

l The DataMan Communications & Programming Guide shows how to integrate your DataMan reader with your
automation software and factory network.
Cognex->DataMan Software v x.x.x->Documentation->Communications And Programming

l The DataMan Reader Configuration Codes document provides printable 2-D codes that you can use to
configure the DataMan reader.
Cognex->DataMan Software v x.x.x->Documentation->English->Reader Configuration Codes

l The DataMan Fixed Mount Readers Reference is a complete online hardware reference for the DataMan fixed-
mount ID readers.
Cognex->DataMan Software v x.x.x->Documentation->English->DM260 ->Fixed Mount Reference Manual

l The DataMan Questions and Answers document provides context-sensitive information. You can view this help
inside the DataMan Setup Tool or as a stand-alone help file.
Cognex->DataMan Software v x.x.x->Documentation->DM260->Questions and Answers

l The Release Notes list detailed system requirements and additional information about this DataMan software
release.
Cognex->DataMan Software v x.x.x->Documentation->DataMan v x.x.x Release Notes

5
 Getting Started

DataMan 260 Accessories

LENS OPTIONS

6.2 mm lens kit (DM150-LENS-62)

l 6.2 mm optics mount

l 6.2 mm lens
l manual lens cap (not assembled)
l long range lens cap (not assembled)
l screws

16 mm lens with extended optics mount (requires the use of an extended front
cover and high-powered red LED)
(DM260-LENS-16)

l 16 mm optics mount
l 16 mm lens
l manual lens cap (assembled)
l screws

Liquid Lens Module (LLM) to be used with 6.2 mm lens or 16 mm lens

(DMA-LLM-150-260)

16 mm lens with Liquid Lens kit (DM260-KIT-16LL)

l 16 mm optics mount

l 16 mm lens
l Liquid Lens Module (DMA-LLM-150-260)

l High Powered red LED illumination (DM260-LED-RED-HP)

l 2-LED half-polarized extended cover (DM260-LENS-16CVR-P)

Note: Do not use on PoE devices!

LENS COVERS

Clear lens cover

(DM150-CVR-CLR)*

6
 Getting Started

Clear lens cover, ESD safe

(DM150-CVR-ESD)*

Extended lens cover

(DM260-LENS-16CVR)**

Extended lens cover, polarized

(DM260-LENS-16CVR-P)**

LIGHT OPTIONS

Red LED illumination (DM150-LED-RED)*

White LED illumination (DM150-LED-WHT) *

Blue LED illumination (DM150-LED-BLU)*

High Powered red LED illumination (DM260-LED-RED-HP)**

Note: *Use with a 6.2 mm lens only!

**Use with a 16 mm lens only! The HP red LED is not supported on PoE devices.

FILTERS

Blue bandpass filter

(DM150-BP470)

Red bandpass filter

(DM150-BP635)

CABLES

Connection cable 24V, I/O, RS-232 (CCBL-05-01)

7
 Getting Started

Connection cable RS-232 (CCB-M12xDB9Y-05)

X-Coded to RJ45 Ethernet Cable, 5 m (CCB-84901-2001-xx, where xx can be

02, 05, 10 or 15, indicating length in meters)

Adapter cable, M12x12 to M8x4/M8x5, 0.5 m (DM260-ADAP-M12M8)

Adapter cable, ETH, M12, X-CODED/A-CODED, 0.5 m (CCB-M12x8MS-XCAC)

MOUNTING BRACKETS

Mounting bracket (DM100-UBRK-000)

Pivot mounting bracket (DM100-PIVOTM-00)

DataMan 362 to DataMan 262 adapter kit (DM-ADAP-PLT)

l Adapter plate
l M3x8 hex socket head screws

8
 Getting Started

DataMan 260 Systems

Omni- 1DMax™ — IDQuick™ — 2DMax™ — for Resolution
directional 1-D Best-In-Class High-Speed 2-D hard to read
Code Reading 1-D Reading Reading DPM and
damaged 2-D
codes
DataMan 260S* √ √ √ 752x480 Global shutter
DataMan 260QL √ √ 752x480 Global shutter
DataMan 260Q √ √ √ 752x480 Global shutter
DataMan 260X √ √ √ √ 752x480 Global shutter
DataMan 262S* √ √ √ 1280x960 Global shutter
DataMan 262QL √ √ 1280x960 Global shutter
DataMan 262Q √ √ √ 1280x960 Global shutter
DataMan 262X √ √ √ √ 1280x960 Global shutter

*Maximum decode rate of 2 codes/sec

9
 Getting Started

Communication Modules
The DataMan 260 is available with the following communication options:

l Ethernet 24V
l Ethernet-PoE (Power over Ethernet)

Ethernet Interfaces
The DataMan 260 readers provide the following interface modules:

l Ethernet / RS-232: This module has Ethernet and RS-232 interfaces and requires 24V external power (Non-
PoE).

l Ethernet-PoE / RS-232: This module has Ethernet and RS-232 interfaces and supports Power over Ethernet.

Note: Connectors without a cable should be covered by a protective cap to meet the IP requirements.

This I/O module has an M12x8 X-coded connector for the Ethernet signals and a (male) M12x12 connector for power, I/O
and RS-232.
The signals on the M12x12 connector are the following:

PIN Signal: Ethernet Signal: Ethernet-PoE

1 OUT_2 OUT_2
2 TXD TXD
3 RXD RXD
4 OUT_3 OUT_3
5 IN_1 IN_1
6 IN_COM IN_COM
7 +24V VIN N.C.
8 +24V RTN RS232GND
9 OUT_COM OUT_COM
10 IN_0 IN_0
11 OUT_0 OUT_0
12 OUT_1 OUT_1

Note: When angled cables are mounted, all of them point downwards or, in the case of the 90° configuration,
backwards.

10
 Getting Started

Reader Layout
The following images shows the built-in lighting system and other features of the DataMan 260 reader.

1 Illumination LEDs
2 LED aimers
3-4* Mounting holes (M3 x 3.5mm)
5 Trigger button
6 Power
7 Train status/Trigger status
8 Good/bad read
9 Network
10 Error
11 Tune button
12 Power, I/O and RS-232
13 Ethernet

Note: *Use only one set of mounting holes (either 3 OR 4) for mounting.

Note: The five status LEDs together also function as a peak meter using an orange light.

Indicator LEDs

Type Signal Color Meaning

Status Power GREEN Power ON
Train status GREEN Trained
YELLOW Untrained
Error RED Error - check device
log
Action Good/bad GREEN Good read
read RED Bad read
Network YELLOW Link up
blink Data transfer
Peak meter Yellow Tune
Focus

11
 Getting Started

Changing Orientation
Perform the following steps to change between straight and angled configuration.

Note: Switching between straight and right angle configuration is recommended only up to 10 times in the lifetime
of the reader.

Note: Disconnect the DataMan 260 reader from power before changing the orientation.

WARNING: Make sure that no electrostatic charges are applied to the PCB. (E.g. wear ESD shoes.) If the main
module is separated from the I/O module, take care to assemble them correctly. Otherwise, IP rating can be lost.

1. Remove the screw covers and unscrew the screws.

2. Disconnect the main module and the I/O module by

firmly pulling them apart.

3. Change the orientation.

Note: Make sure that the gasket it properly seated on the main module. Ensure that the flat gasket side is facing
away from the module.

Place the bottom edge of the gasket onto the underside of the main module. Press on the top edge to fully seat the
gasket:

12
 Getting Started

Note: The flat side of the gasket (marked as "Front" in the image above) has to face outside.

WARNING: Do not touch any electrical component.

4. Connect the I/O module to the main module.

13
 Getting Started

5. Loosely fasten the modules together with the two T10 cap nut
screws until they attach to the housing surface, but do not torque.

6. After each cap nut has been fastened, torque to 0.12 Nm and place
back the screw covers.

Note: There are unique left and right screw covers. Take care to
attach them correctly.

14
 Getting Started

Dimensions

The DataMan 260 consists of three main parts:

1. Optics module (lens including lens mount, illumination and front cover including filter mounting option for a
Diameter (Ø): 12.3mm<Ø<12.7mm, Thickness (t): 1.6mm<t<2mm filter)
2. Main module, including sensor and CPU
3. I/O module

15
 Getting Started

The size of the DataMan 260 in the straight configuration is shown in the following figure:

The size of the DataMan 260 in the angled configuration is shown in the following figure:

16
 Getting Started

Installing an Optical Filter

Perform the following steps to install an optical filter in the optics module of the DataMan 260 reader.

Note: Disconnect the DataMan 260 reader from power before installing an optical filter.

Observe the following constraints on the filter:

l Diameter (Ø): 12.3mm<Ø<12.7mm

l Thickness (t): 1.6mm<t<2mm filter

1. First, remove the front cover: unscrew the four screws and take off the LED cover.

2. Insert the filter at the bottom side of the round opening in the transparent plastic part.

3. Push the top side of the filter firmly until it is sitting flat against the PCB.

Note: Use finger to push the filter in and then a q-tip to clean the filter, or use a q-tip to push the filter into
place.

17
 Getting Started

4. Attach the front cover. Observing the tightening sequence below, tighten all four screws to 9 Ncm using a torque
wrench.

5. Note: The rib in the front cover must be oriented to the top side.

18
 Getting Started

Installing a Liquid Lens

Perform the following steps to install a liquid lens on your DataMan 260 reader.

Note: Disconnect the DataMan 260 reader from power before installing the liquid lens.

1. Remove the front cover: unscrew the four screws and take off the LED cover.

2. Remove the illumination module.

3. Turn the lens cap to the 105 mm position.

4. Remove the lens cap from the imager lens by pulling it.

Do not rotate the imager lens while the lens cap is removed. Otherwise, focus calibration will be lost.

19
 Getting Started

5. Attach the liquid lens accessory by aligning the 2x2 connectors of the liquid lens with the 2x2 sockets on the
optics mount.

6. Press the liquid lens onto the imager lens until you reach the stop.

7. Reattach the illumination.

8. Attach the front cover. Observing the tightening sequence below, tighten all four screws to 9 Ncm using a torque
wrench.

Note: The rib in the front cover must be oriented to the top side.

20
 Getting Started

Note: The DataMan 260 liquid lens must be calibrated after field exchange. This can be done under Focus
Settings in the DataMan Setup Tool. For more information, see the DataMan Questions and Answers
document.
A reboot is required for the lens to operate with the new settings.

21
 Getting Started

Changing from a 6.2 mm Lens to a 16 mm Lens

Perform the following steps to change a 6.2 mm lens to a 16 mm lens on your DataMan 260 reader.

Note: Disconnect the DataMan 260 reader from power before changing lenses.

WARNING: This modification must be made in a dust-free and ESD safe area.

1. Remove the front cover: unscrew the four screws and take off the LED cover.

2. Remove the illumination module.

3. Unscrew the two Phillips head screws and remove the 6.2 mm lens mount.

4. Attach the 16 mm lens mount.

5. Fasten the two Phillips head screws to 0.06 Nm using a torque wrench.

22
 Getting Started

6. In the case of a manual focus lens, press the 16 mm lens cap onto the lens. The lens has 12 cutouts so it can be
locked in steps of 30 degrees.

In the case of a liquid lens, mount the liquid lens cap onto the 16 mm lens. (See Installing a Liquid Lens.)

7. Attach the illumination board.

Note: Take care to attach the illumination with the right orientation.

8. Attach the front cover. Observing the tightening sequence below, tighten all four screws to 9 Ncm using a torque
wrench.

Note: The rib in the front cover must be oriented to the top side.

23
 Getting Started

Changing to an Illumination with a Different Color

Perform the following steps to change the illumination.

Note: Disconnect the DataMan 260 reader from power before changing to an illumination with a different color.

1. Remove the front cover: unscrew the four screws and take off the LED cover.

2. Remove the illumination module.

3. Attach a new color illumination module.

Note: Take care to attach the illumination with the right orientation.

24
 Getting Started

4. Attach the front cover. Observing the tightening sequence below, tighten all four screws to 9 Ncm using a torque
wrench.

Note: The rib in the front cover must be oriented to the top side.

25
 Setting Up Your DataMan

Setting Up Your DataMan

Mounting
Mounting the DataMan 260 at a slight angle (15°) can reduce reflections and improve reader performance.

26
 Setting Up Your DataMan

Replacing a DataMan 362 with a DataMan 262 on the Factory

Floor
An adapter kit (DM-ADAP-PLT) is available for DataMan 262 using which you can replace a DataMan 362 device with a
DataMan 262 device in the field.

The kit includes the following:

Adapter plate M3x8 hex socket head screws

The adapter plate has 8 holes: 4 threaded and 4 through holes.

You can attach the adapter plate to the DataMan 262 reader in two positions:
Position 1:
The mechanically correct position. The DataMan 262 device's front surface is inside as compared to the DataMan 362
front surface.

27
 Setting Up Your DataMan

Position 2:
The optically correct position. The Field of View is more or less same as that of DataMan 362, but the front surface is
sticking out compared to DataMan 362.

Note: The adapter plate must always be connected to the mounting holes of the DataMan 262 IO modul. The
threaded holes in the adapter plate are maching with the DataMan 362 mounting holes.

28
 Setting Up Your DataMan

I/O Cables

The I/O breakout cable (CCBL-05-01) provides access to trigger and high-speed outputs. Unused wires can be clipped
short or tied back using a tie made of non-conductive material. For RS-232, use the Power Supply return path for ground.

This image shows the plug on the device:

Signal: Ethernet

29
 Setting Up Your DataMan

Signal: Ethernet-PoE

Acquisition Triggering
The acquisition trigger input on the reader is opto-isolated. To trigger from an NPN (pull-down) type photo-detector or
PLC output, connect In 0 to +24V and connect Common In to the output of the detector. When the output turns on, it pulls
Common In down to 0V, turning the opto-coupler on.

To trigger from a PNP (pull-up) photo-detector or PLC output, connect In 0 to the output of the detector and connect
Common In to 0V. When the output turns on, it pulls In 0 up to 24V, turning the opto-coupler ON.

30
 Setting Up Your DataMan

High-Speed Output Lines

The high-speed outputs can be used as either NPN (pull-down) or PNP (pull-up) lines. For NPN lines, the external load
should be connected between the output and the positive supply voltage (<28V). The outputs pull down to less than 3V
when ON, which causes current to flow through the load. When the outputs are OFF, no current flows through the load.

Specification Description
Voltage 28V maximum through external load
Current 50mA maximum sink current
OFF state leakage current 100µA
External load resistance 240 Ohms to 10K Ohms
Each line rated at a maximum 50mA, protected against over-current, short circuits
and transients from switching inductive loads. High current inductive loads require
external protection diode.

For PNP lines, the external load should be connected between the output and the negative supply voltage (0V). When
connected to a 24VDC power supply, the outputs pull up greater than 21V when ON, and current flows through the load.
When the outputs are OFF, no current flows through the load.

31
 Setting Up Your DataMan

High-Speed Output Wiring

To connect to an NPN-compatible PLC input, connect Output 0 or Output 1 directly to the PLC input. When enabled, the
output pulls the PLC input down to less than 3V.

To connect to a PNP-compatible PLC input, connect Output 0 or Output 1 directly to the PLC input. When enabled, the
output pulls the PLC input up to greater than 21V.

To connect the high-speed outputs to a relay, LED or similar load, connect the negative side of the load to the output and
the positive side to +24V. When the output switches on, the negative side of the load is pulled down to less than 3V, and
24 appears across the load. Use a protection diode for a large inductive load, with the anode connected to the output
and the cathode connected to +24V.

32
 Setting Up Your DataMan

Ethernet Cables
The Ethernet cable (CCB-84901-2001-05) provides Ethernet connection for network communications. The Ethernet
cable can be connected to a single device or provide connections to multiple devices via a network switch or router.

Note: Cables are sold separately. The wiring for this cable follows standard industrial Ethernet M12 specifications.
This differs from the 568B standard.

X-coded to RJ45 Cable

P2 Pin# Wire Color P1 Pin#

1/C White/Orange 1
2/C Orange 2
3/C White/Green 3
4/C Blue 8
5/C White/Blue 7
6/C Green 4
7/C White/Brown 5
8/C Brown 6

33
 Setting Up Your DataMan

Installing the DataMan Software

Perform the following steps to install DataMan Setup Tool:

1. Check the DataMan Release Notes for a full list of system requirements.
2. Download the DataMan Setup Tool from http://www.cognex.com/support/dataman and follow the on-screen
steps.
3. Connect the DataMan 260 to your PC.
4. Choose Start->Programs->Cognex->DataMan Software vx.x.x->Setup Tool to launch Setup Tool. Detected
readers will appear under COM ports.
5. Click Refresh to update the list of connected devices.

6. Select the device from the Network list (Discovered Devices) and click Connect.

34
 Setting Up Your DataMan

Setting the Focus Position

DataMan 260 can operate in one of three distance ranges. Follow the steps below to set the focus position.

1. Remove the screws and the front cover.

2. Using a flathead screwdriver, set the focus position from the front. Always turn clockwise to focus to a larger
distance and counterclockwise to focus to a shorter distance.

Note: If an optical filter has been mounted, first disconnect the DataMan 260 reader from power and remove
the illumination module with the filter before adjusting the focus.

35
 Setting Up Your DataMan

3. Remount the front cover. Observing the tightening sequence below, tighten all four screws to 9 Ncm using a
torque wrench.

4. Note: If you use an optical filter and the illumination was removed, remount the illumination module first and
then remount the front cover.

5. Note: The rib in the front cover must be oriented to the top side.

36
 Setting Up Your DataMan

Field of View and Reading Distances

DataMan 260 Readers with a 6.2 mm Lens
Short Range (Focused to 105 mm)
The following tables show the field of view (FoV) widths of the 6.2 mm lens focused to 105 mm at various distances.
VGA

Distances in mm 2D min. code 1D min. code

40 4 MIL 4 MIL
65 5 MIL 4 MIL
105 10 MIL 6 MIL

1.2 Mp

Distances in mm 2D min. code 1D min. code

40 3 MIL 2 MIL
65 4 MIL 2 MIL
105 7 MIL 5 MIL

The following maps show the FoV of the DataMan 260 readers with a 6.2 mm lens. The horizontal and vertical field of
view is shown for working distances of 40 mm, 65 mm and 105 mm.
VGA + 6.2 mm Lens

37
 Setting Up Your DataMan

1.2 Mp + 6.2 mm Lens

Long Range (Focused to 190 mm)

The following tables show the field of view (FoV) widths of the 6.2 mm lens focused to 190 mm at various distances.
VGA

Distances in mm 2D min. code 1D min. code

150 12 MIL 6 MIL
190 15 MIL 10 MIL
225 18 MIL 10 MIL
375 30 MIL 15 MIL
500 35 MIL 20 MIL
1m - 35 MIL

1.2 Mp

Distances in mm 2D min. code 1D min. code

150 12 MIL 5 MIL
190 10 MIL 6 MIL
225 15 MIL 6 MIL
375 20 MIL 10 MIL
500 25 MIL 15 MIL
1m - 30 MIL

38
 Setting Up Your DataMan

The following maps show the FoV of the DataMan 260 readers with a 6.2 mm lens. The horizontal and vertical field of
view is shown for working distances of 150 mm, 190 mm, 225 mm, 375 mm and 500 mm.
VGA + 6.2 mm Lens

1.2 Mp + 6.2 mm Lens

39
 Setting Up Your DataMan

DataMan 260 Readers with a 16 mm Lens

The following tables show the field of view (FoV) widths of the 16 mm lens at various distances.
VGA

Distances in mm 2D min. code 1D min. code

80 3 MIL 2 MIL
150 5 MIL 3 MIL
190 6 MIL 4 MIL
225 7 MIL 4 MIL
375 12 MIL 5 MIL
500 15 MIL 10 MIL
1m 25 MIL 15 MIL

1.2 Mp

Distances in mm 2D min. code 1D min. code

80 2 MIL 2 MIL
150 3 MIL 2 MIL
190 4 MIL 2 MIL
225 4 MIL 3 MIL
375 7 MIL 4 MIL
500 10 MIL 6 MIL
1m 20 MIL 15 MIL

The following maps show the FoV of the DataMan 260 readers with a 16 mm lens. The horizontal and vertical field of
view is shown for working distances of 80 mm, 150 mm, 225 mm, 375 mm, 500 mm and 1000 mm.
DataMan 260 with a 16 mm Lens

40
 Setting Up Your DataMan

DataMan 262 with a 16 mm Lens

41
 Setting Up Your DataMan

External Triggering and Trigger Modes

If you are using external triggering, you can use any of the following methods to trigger your DataMan 260 reader:

1. Press the Trigger button ( ) on the reader.

2. Send a pulse on the I/O cable: Trigger + (blue), Trigger - (black).

3. Send a serial trigger command over the RS-232 or the Ethernet connection.

4. Click the Trigger button ( ) or press <Ctrl>-T in DataMan Setup Tool.

DataMan 260 supports a variety of trigger modes:

l Single: Acquires a single image and attempts to decode any symbol it contains or more than one symbol in cases
where multicode is enabled. The reader relies on an external trigger source.
l Presentation: Repeatedly scans for a symbol and decodes it whenever one is detected. The reader relies on an
internal timing mechanism to acquire images.
l Manual (default): Begins acquiring images when you press the trigger button on the reader or the discrete trigger
input is activated, and continues acquiring images until a symbol is found and decoded or you release the button
or the discrete trigger input is deactivated.
l Burst: Performs multiple image acquisitions based on an external trigger and decodes one or multiple symbols
appearing in the sequence of images.
l Self: Similar to Presentation mode in that the reader perpetually scans for symbols and decodes them each time
one is detected. Unlike Presentation mode, however, Self mode supports multicode results and a decode attempt
occurs with every image. The main difference between Self and Presentation is the fixed and exact interval for
image acquisitions in Self.
l Continuous: Begins acquiring images based on a single external trigger and continues to acquire images until a
symbol is found and decoded, or until multiple images containing as many codes as specified in multicode mode
are located, or until the trigger is released.

Training and Trigger Modes

Training is supported for the following trigger modes:

l Single trigger

l Burst mode
l Self trigger
l Continuous mode

Training
Training your reader with the expected symbology may help increase decode yield.
To train your reader, place a code in front of the reader and do one of the following:

l Press and hold the trigger button ( ) for at least 3 seconds and the release it.

l Click and hold the trigger button in Setup Tool ( ) for at least 3 seconds and then release it.

l Click Train Code in the Action ribbon of DataMan Setup Tool.

If using Single trigger mode, upload the code through File -> Train Image.

42
 Setting Up Your DataMan

Note: You can use training in Single, Burst, Continuous or Self trigger modes. Only a single symbol of each kind of
symbology can be trained per read setup.

DataMan 260 reports the status of the training and brightness optimization operations using its signaling LEDs. The
second LED from left on the reader flashes green to indicate that the reader is currently trained, or yellow to indicate that
it is not trained.

Connect the reader to the Setup Tool to untrain it and allow it to recognize other enabled symbologies.

Incremental Training for Multiple Symbologies

If you want to train the reader to recognize multiple symbologies, you can present a single image showing all the desired
symbologies and perform the training procedure described in the previous section.
If you cannot present a single image showing all the necessary symbologies, you can enable incremental training on the
Training tab of the Symbology Settings page:

43
 Setting Up Your DataMan

With incremental training enabled, you can train the reader using multiple images showing the symbologies you expect
to decode. The reader will train each new symbology while retaining the existing trained symbologies.

Tuning
By tuning, your DataMan 260 reader automatically selects the best settings for the given reading situation, based on
parameters of illumination, camera and decoder properties, and focal distance. Tuning autodiscriminates all enabled
symbologies (both 1-D and 2-D). If multiple symbols are found in the field of view, tuning locks on the first one found. Use
this feature to create an optimum setting to read your codes.
You can use any of the following methods to tune your reader:

Press the Tune button ( ) at least for 3 seconds on your reader. The first press starts the tuning and the second
press cancels the tuning, if it is still ongoing.

Turn on tuning in DataMan Setup Tool ( ).

Start tuning by sending a DMCC, for more information, see the Command Reference, available through the Windows
Start menu or the Setup Tool Help menu.
Use Input line 1 for tuning. Go to the System Settings pane in Setup Tool and check Tune. You can also use the In1
button on the toolbar.

44
 Setting Up Your DataMan

Industrial Protocols
The DataMan 260 readers support the following industrial protocols:

l EtherNet/IP™
l PROFINET
l MC Protocol
l Modbus TCP

Select industrial protocol samples and tools you want to use when you install the DataMan Software. There are three
ways to enable or disable Industrial Protocols. Using either method, a reboot is required for the changes to take effect.

1. Enable the protocols using the Industrial Protocols pane of the DataMan Setup Tool (under Communication
Settings).
2. Scan the appropriate Reader Configuration codes (see Reader Configuration Codes available through the
Windows Start menu or the Setup Tool Help menu).

3. Send the appropriate DMCC (see Command Reference available through the Windows Start menu or the Setup
Tool Help menu).

For more information on using the industrial protocols, read the DataMan Communications and Programming Guide
available through the Windows Start menu or the Setup Tool Help menu.

45
 Setting Up Your DataMan

DataMan 260 Specifications

Weight 142 g
Operating 0ºC — 40ºC (32ºF — 104ºF)
Temperature
Storage -10ºC — 60ºC (-14ºF — 140ºF)
Temperature
Maximum <95% (non-condensing)
Humidity
Environmental IP65
Shock and • IEC 60068-2-27: 1000 shocks, semi-sinusoidal, 11g, 10ms
Vibration • IEC 60068-2-6: vibration test in each of the three main axis for 2 hours @ 10
Gs (10 to 500 Hz at 100m/s2 / 15mm)
RS-232 RxD, TxD according to TIA/EIA-232-F
Codes Data MatrixTM (IDMax: ECC0, 50, 80, 100, 140, and 200; IDQuick: ECC200)
QR Code and microQR Code UPC/EAN/JAN Codabar, Interleaved 2 of 5,
Code 25, Code 39, Code 128, and Code 93, Pharma, Postal, RSS/CS, PDF
417, MicroPDF 417, AztecCode, DotCode, MaxiCode, MSI
Discrete I/O HS Output 0, 1, 2, 3 IMAX @ 24 VDC 50 mA
operating
Limits RMAX @ 12 VDC 150 Ω
@ 24 VDC 470 Ω

Input 0 (Trigger) VIH ±15 — ±25 V

Input 1 VIL 0 — ±5 V
ITYP @ 12 VDC 2.0 mA
@ 24 VDC 4.2 mA

Power Supply Ethernet with external power (no PoE): 24 VDC +/- 10%
l

Requirements
ETH: Class 1 PoE supply, max. 3.84 W
l

Supplied by LPS or NEC class 2 only

Ethernet 10/100
Speed
Duplex Mode Full duplex or half duplex

Imager Specifications
Specification DataMan 260 Imager DataMan 262 Imager
Image Sensor 1/3 inch CMOS 1/3 inch CMOS
Image Sensor 4.51 mm x 2.88 mm (W x H), 6.0 μm 4.8 mm x 3.6 mm (W x H), 3.75 μm
Properties square pixels square pixels
Image Resolution 752 x 480 1280 x 960
(pixels)
Lens Type S-mount 6.2 mm F:5 (with optional S-mount 6.2 mm F:5 (with optional
liquid lens) liquid lens)
S-mount 16 mm F:7 (with optional S-mount 16 mm F:7 (with optional
liquid lens) liquid lens)

46
 Setting Up Your DataMan

Illumination Options
Illumination USB Powered PoE Powered 24V Externally Powered
Board Max. exposure Max. duty Max. exposure Max. duty Max. exposure Max. duty
time cycle time cycle time cycle
Standard Red 500 µs 3% 500 µs 3% 1 ms 6%

High power red Not supported Not supported 10 ms 10%

Standard White 500 µs 3% 500 µs 3% 1 ms 6%

Standard Blue 500 µs 3% 500 µs 3% 1 ms 6%

IR 500 µs 3% 500 µs 3% 1 ms 6%

47
 Precautions

Precautions
CAUTION: This device requires the use of an LPS or NEC class 2 power supply (non-PoE device) or the use of a
PoE Class 1 (PoE device).

Note: For product support, contact http://support.cognex.com

Observe these precautions when installing the Cognex product, to reduce the risk of injury or equipment damage:

l To reduce the risk of damage or malfunction due to over-voltage, line noise, electrostatic discharge (ESD), power
surges, or other irregularities in the power supply, route all cables and wires away from high-voltage power
sources.
l Changes or modifications not expressly approved by the party responsible for regulatory compliance could void
the user’s authority to operate the equipment.
l Cable shielding can be degraded or cables can be damaged or wear out more quickly if a service loop or bend
radius is tighter than 10X the cable diameter. The bend radius must be at least six inches from the connector.
l  Class A Equipment (broadcasting and communication equipment for office work): Seller and user shall be
notified that this equipment is suitable for electromagnetic equipment for office work (Class A) and can be used
outside the home.
l This device should be used in accordance with the instructions in this manual.
l All specifications are for reference purpose only and may be changed without notice.

48
 Regulations/Conformity

Regulations/Conformity
The DataMan 260 has Regulatory Model 1AA5 and meets or exceeds the requirements of all applicable standards
organizations for safe operation. However, as with any electrical equipment, the best way to ensure safe operation is to
operate them according to the agency guidelines that follow. Please read these guidelines carefully before using your
device.

Regulator Specification
USA FCC 47 CFR Part 15 Subpart B, Class A
Canada ICES-003
European EN55022 (CISPR 22) Class A
Community EN55024:1998 +A1:2001 +A2: 2003
EN60950
Australia C-TICK, AS/NZS CISPR 22 / EN 55022 for Class A
Equipment
Japan J55022, Class A

Note: For the most up-to-date regulations and conformity information, please refer to the Cognex online support
site: http://www.cognex.com/Support.

CAUTION: IP protection is ensured only when all connectors are attached to cables or shielded by a sealing cap.

Safety and Regulatory

European The CE mark on the product indicates that the system has been tested to and conforms with the
Compliance provisions noted within the 2004/108/EC Electromagnetic Compatibility Directive and the 2006/95/EC
Low Voltage Directive. For further information please contact: Cognex Corporation, One Vision Drive
Natick, MA 01760 USA.
Cognex Corporation shall not be liable for use of our product with equipment (i.e., power supplies,
personal computers, etc.) that is not CE marked and does not comply with the Low Voltage Directive.
FCC Class A This equipment has been tested and found to comply with the limits for a Class A digital device,
Compliance pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
Statement against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause harmful interference, in which case the user
will be required to correct the interference at personal expense.
Canadian This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la
Compliance classe A est conforme à la norme NMB-003 du Canada.
C-Tick Conforms to AS/NZS CISPR 22/ EN 55022 for Class A Equipment.
Statement

UL and cUL UL and cUL listed: UL60950-1 1st ed. and CSA C22.2 No.60950-1 1st ed. Certified to CB scheme IEC
Statement 60950-1:2001 1st ed.

For European Community Users

Cognex complies with Directive 2002/96/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 27 January
2003 on waste electrical and electronic equipment (WEEE).
This product has required the extraction and use of natural resources for its production. It may contain hazardous
substances that could impact health and the environment, if not properly disposed.

49
 Regulations/Conformity

In order to avoid the dissemination of those substances in our environment and to diminish the pressure on the natural
resources, we encourage you to use the appropriate take-back systems for product disposal. Those systems will reuse or
recycle most of the materials of the product you are disposing in a sound way.

The crossed out wheeled bin symbol informs you that the product should not be disposed of along with municipal
waste and invites you to use the appropriate separate take-back systems for product disposal.
If you need more information on the collection, reuse, and recycling systems, please contact your local or regional waste
administration.
You may also contact your supplier for more information on the environmental performance of this product.

50