Flowmeter 2051CF

Product Data Sheet
June 2013
00813-0400-4485, Rev EC
Rosemount 2051CF DP Flowmeters
 Up to 2.00% volumetric flow accuracy at 5:1 turndown
 Available with HART and FOUNDATION fieldbus Protocols
 2-year stability
 Aluminum and SST housings available
 4-20mA HART, FOUNDATION fieldbus, Low Power HART
 Conventional bid spec compliance - optional reference accuracy and stability improvements
 Ease-of-Use features, enhanced EDDL screens, optional external zero and span buttons
Rosemount DP Flow June 2013
Rosemount 2051CF Flowmeter Series

Rosemount 2051CF Flowmeters combine the 2051 Pressure transmitter and the latest primary
element technology: Annubar Averaging Pitot Tube, Compact Conditioning Orifice Plate and
Integral Orifice Plate.
Configuration Transmitter Output Code
®
4-20 mA HART
-2051 A
-2051 with Selectable HART(1)
Low Power
-2051 M
-2051 with Selectable HART(1)
FOUNDATION Fieldbus F
Profibus W
(1) The enhanced 4-20 mA HART device can be ordered with Transmitter Output option code A plus any of
the following new option codes: M4, QT, DZ, CR, CS, CT, HR5, HR7.
Additional Information
Specifications: page 20
Product Certifications: page 25
Dimensional Drawings: page 37
Installation and Flowmeter Orientation: Click Here
Contents
Rosemount 2051CF Flowmeter Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2
Rosemount 2051CFA Annubar Flowmeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3
Rosemount 2051CFC Compact Flowmeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 9
Rosemount 2051CFP Integral Orifice Flowmeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 14
2051CF specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 20
Rosemount 2051CF product certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 25
Dimensional drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 37
Installation and Flowmeter Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Click Here
2 www.rosemount.com
June 2013 Rosemount DP Flow
Rosemount 2051CFA Annubar Flowmeter

Annubar flowmeters reduce permanent pressure loss by creating less blockage in the pipe
Ideal for large line size installations when cost, size, and weight of the flowmeter are concerns
Table 1. Rosemount 2051CFA Annubar Flowmeter Ordering Information

★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Model Product Description
2051CFA Annubar Flowmeter
Measurement Type
Standard Standard
D Differential Pressure ★
Fluid Type
Standard Standard
L Liquid ★
G Gas ★
S Steam ★
Line Size
Standard Standard
020 2-in. (50 mm) ★
025 21/2-in. (63.5 mm) ★
030 3-in. (80 mm) ★
035 31/2-in. (89 mm) ★
040 4-in. (100 mm) ★
050 5-in. (125 mm) ★
060 6-in. (150 mm) ★
070 7-in. (175 mm) ★
080 8-in. (200 mm) ★
100 10-in. (250 mm) ★
120 12-in. (300 mm) ★
Pipe I.D. Range (See “Pipe I.D. Range Code” on page 34)
Standard Standard
C Range C from the Pipe I.D. table ★
D Range D from the Pipe I.D. table ★
Expanded
A Range A from the Pipe I.D. table
B Range B from the Pipe I.D. table
E Range E from the Pipe I.D. table
Z Non-standard Pipe I.D. Range or Line Sizes greater than 12 inches
Pipe Material / Mounting Assembly Material
Standard Standard
C Carbon steel (A105) ★
S 316 Stainless Steel ★
0(1) No Mounting (Customer Supplied)
Expanded
G Chrome-Moly Grade F-11
N Chrome-Moly Grade F-22
J Chrome-Moly Grade F-91
www.rosemount.com 3

Piping Orientation
Standard Standard
H Horizontal Piping ★
D Vertical Piping with Downwards Flow ★
U Vertical Piping with Upwards Flow ★
Annubar Type
Standard Standard
P Pak-Lok ★
F Flanged with opposite side support ★
Sensor Material
Standard Standard
S 316 Stainless Steel ★
Sensor Size
Standard Standard
1 Sensor size 1 — Line sizes 2-in. (50 mm) to 8-in. (200 mm) ★
2 Sensor size 2 — Line sizes 6-in. (150 mm) to 96-in. (2400 mm) ★
3 Sensor size 3 — Line sizes greater than 12-in. (300 mm) ★
Mounting Type
Standard Standard
T1 Compression or Threaded Connection ★
A1 150# RF ANSI ★
A3 300# RF ANSI ★
A6 600# RF ANSI ★
D1 DN PN16 Flange ★
Expanded
R1 150# RTJ Flange
R3 300# RTJ Flange
R6 600# RTJ Flange
Opposite Side Support or Packing Gland
Standard Standard
0 No opposite side support or packing gland (Required for Pak-Lok and Flange-Lok models) ★
Opposite Side Support – Required for Flanged Models
C NPT Threaded Opposite Support Assembly – Extended Tip ★
D Welded Opposite Support Assembly – Extended Tip ★
Isolation Valve for Flo-Tap Models
Standard Standard
0(1) Not Applicable or Customer Supplied ★
Temperature Measurement
Standard Standard
T Integral RTD – not available with Flanged model greater than class 600# ★
0 No Temperature Sensor ★
4 www.rosemount.com

Transmitter Connection Platform
Standard Standard
3 Direct-mount, Integral 3-valve Manifold– not available with Flanged model greater than class 600 ★
5 Direct -mount, 5-valve Manifold – not available with Flanged model greater than class 600 ★
7 Remote-mount NPT Connections (1/2-in. FNPT) ★
Expanded
8 Remote-mount SW Connections (1/2-in.)
Differential Pressure Range
Standard Standard
1 0 to 25 in H2O (0 to 62,3 mbar) ★
2 0 to 250 in H2O (0 to 623 mbar) ★
3 0 to 1000 in H2O (0 to 2,5 bar) ★
Transmitter Output
Standard Standard
A(2) 4–20 mA with digital signal based on HART Protocol ★
F FOUNDATION fieldbus Protocol ★
Expanded
M(2) Low-Power, 1-5 Vdc with Digital Signal Based on HART Protocol
Transmitter Housing Material(3) Conduit Entry Size
Standard Standard
A Aluminum 1/2-14 NPT ★
B Aluminum M20 x 1.5 ★
J SST 1/2-14 NPT ★
K(4) SST M20 x 1.5 ★
Expanded
D Aluminum G1/2
M(4) SST G1/2
Transmitter Performance Class
Standard Standard
1 2.3% flow rate accuracy, 5:1 flow turndown, 2-year stability ★
Options (Include with selected model number)

Pressure Testing
Expanded
P1(5) Hydrostatic Testing with Certificate
PX(5) Extended Hydrostatic Testing
Special Cleaning
Expanded
P2 Cleaning for Special Services
PA Cleaning per ASTM G93 Level D (Section 11.4)
Material Testing
Expanded
V1 Dye Penetrant Exam
Material Examination
Expanded
V2 Radiographic Examination
www.rosemount.com 5

Special Inspection
Standard Standard
QC1 Visual & Dimensional Inspection with Certificate ★
QC7 Inspection & Performance Certificate ★
Surface Finish
Standard Standard
RL Surface finish for Low Pipe Reynolds # in Gas & Steam ★
RH Surface finish for High Pipe Reynolds # in Liquid ★
Material Traceability Certification
Standard Standard
Q8(6) Material Traceability Certification per EN 10474:2004 3.1 ★
Code Conformance
Expanded
J2 ANSI/ASME B31.1
J3 ANSI/ASME B31.3
Materials Conformance
Expanded
J5(7) NACE MR-0175 / ISO 15156
Country Certification
Standard Standard
J6 European Pressure Directive (PED) ★
Expanded
J1 Canadian Registration
Instrument Connections for Remote Mount Options
Standard Standard
G2 Needle Valves, Stainless Steel ★
G6 OS&Y Gate Valve, Stainless Steel ★
Expanded
G1 Needle Valves, Carbon Steel
G3 Needle Valves, Alloy C-276
G5 OS&Y Gate Valve, Carbon Steel
G7 OS&Y Gate Valve, Alloy C-276
Special Shipment
Standard Standard
Y1 Mounting Hardware Shipped Separately ★
Product Certifications
Standard Standard
E1(4) ATEX Flameproof ★
E2 INMETRO Flameproof ★
E3(4) China Flameproof ★
E5 FM Explosion-proof, Dust Ignition-proof ★
E6 CSA Explosion-proof, Dust Ignition-proof, Division 2 ★
E7(4) IECEx Flameproof, Dust Ignition-proof ★
I1(4) ATEX Intrinsic Safety ★
I2(4) INMETRO Intrinsic Safety ★
I3(4) China Intrinsic Safety ★
I5 FM Intrinsically Safe, Division 2 ★
6 www.rosemount.com

I6 CSA Intrinsically Safe ★
I7(4) IECEx Intrinsic Safety ★
IA(8) ATEX FISCO Intrinsic Safety; for FOUNDATION fieldbus protocol only ★
IE(8) FM FISCO Intrinsically Safe ★
IF(8) CSA FISCO Intrinsically Safe ★
IG(8) IECEx FISCO Intrinsically Safe ★
K1(4) ATEX Flameproof, Intrinsic Safety, Type n, Dust ★
K5 FM Explosion-proof, Dust Ignition-proof, Intrinsically Safe, Division 2 (combination of E5 and I5) ★
K6 CSA Explosion-proof, Dust Ignition-proof, Intrinsically Safe, Division 2 (combination of E6 and I6) ★
K7(4) IECEx Flameproof, Dust Ignition-proof, Intrinsic Safety, Type n (combination of E7, I7, and N7) ★
KA(4) ATEX and CSA Flameproof, Intrinsically Safe, Division 2 ★
FM and CSA Explosion-proof, Dust Ignition-proof, Intrinsically Safe, Division 2 (combination of E5, E6, I5, ★
KB
and I6)
KC(4) FM and ATEX Explosion-proof, Intrinsically Safe, Division 2 ★
KD(4) FM, CSA, and ATEX Explosion-proof, Intrinsically Safe (combination of E5, I5, E6, I6, E1, and I1) ★
N1(4) ATEX Type n ★
N7(4) IECEx Type n ★
ND(4) ATEX Dust ★
Shipboard Approvals
Standard Standard
SBS American Bureau of Shipping ★
Sensor Fill Fluid and O-ring Options
Standard Standard
L1 Inert Sensor Fill Fluid ★
L2 Graphite-Filled (PTFE) O-ring ★
LA Inert Sensor Fill Fluid and Graphite-Filled (PTFE) O-ring ★
Display and Interface Options
Standard Standard
(9) ★
M4 LCD Display with Local Operator Interface
M5 LCD Display ★
Transmitter Calibration Certification
Standard Standard
Q4 Calibration Certificate for Transmitter ★
Quality Certification for Safety
Standard Standard
(9) ★
QS Prior-use certificate of FMEDA data
QT(10) Safety certified to IEC 61508 with certificate of FMEDA ★
Transient Protection
Standard Standard
T1(11) Transient terminal block ★
Manifold for Remote Mount Option
Standard Standard
F2 3-Valve Manifold, Stainless Steel ★
Expanded
F1 3-Valve Manifold, Carbon Steel
F5 5-Valve Manifold, Carbon Steel
www.rosemount.com 7

PlantWeb Control Functionality
Standard Standard
A01(8) FOUNDATION fieldbus Advanced Control Function Block Suite ★
Hardware Adjustments
Standard Standard
D4(12) Zero and Span Hardware Adjustments ★
DZ(12) Digital Zero Trim ★
Alarm Limit
Standard Standard
C4(9)(13) NAMUR Alarm and Saturation Levels, High Alarm ★
CN(9)(13) NAMUR Alarm and Saturation Levels, Low Alarm ★
CR(10) Custom alarm and saturation signal levels, high alarm (requires C1 and Configuration Data Sheet) ★
CS(10) Custom alarm and saturation signal levels, low alarm (requires C1 and Configuration Data Sheet) ★
CT(10) Low alarm (standard Rosemount alarm and saturation levels) ★
Ground Screw
Standard Standard
V5(14) External Ground Screw Assembly ★
HART Revision Configuration
Standard Standard
(10)(15) ★
HR5 Configured for HART Revision 5
HR7(10)(16) Configured for HART Revision 7 ★
Typical Model Number: 2051CFA D L 060 D C H P S 2 T1 0 0 0 3 2A A 1A 3
(1) Provide the “A” dimension for Flanged (page 38) and Pak-Lok (page 37).
(2) HART Revision 5 is the default HART output. The Enhanced 3051 can be factory or field configured to HART Revision 7. To order HART Revision 7 factory configured,
add option code HR7.
(3) Material specified is cast as follows: CF-8M is the cast version of 316 SST, CF-3M is the cast version of 316L SST. For housing, material is aluminum with polyurethane
paint.
(4) Not available with Low Power Output Code M.
(5) Applies to assembled flowmeter only, mounting not tested.
(6) Instrument Connections for Remote Mount Options and Isolation Valves for Flo-tap Models are not included in the Material Traceability Certification.
(7) Materials of Construction comply with metallurgical requirements within NACE MR0175/ISO for sour oil field production environments. Environmental limits apply
to certain materials. Consult latest standard for details. Selected materials also conform to NACE MR0103 for sour refining environments.
(8) Only valid with FOUNDATION fieldbus Output Code F.
(9) Not available with Output Protocol code F.
(10) Only available with 4-20 mA HART output (output Code A).
(11) The T1 option is not needed with FISCO Product Certifications, transient protection is included with the FISCO Product Certification code IA.
(12) Only available with 4-20 mA HART (output codes A and M).
(13) NAMUR-Compliant operation is pre-set at the factory and cannot be changed to standard operation in the field.
(14) The V5 option is not needed with the T1 option; external ground screw assembly is included with the T1 option.
(15) Configures the HART output to HART Revision 5. The device can be field configured to HART Revision 7 if needed.
8 (16) Configures the HART output to HART Revision 7. The device can be field configured to HART Revision 5 if needed. www.rosemount.com
Rosemount 2051CFC Compact Flowmeter

Compact Conditioning flowmeters reduce straight piping requirements to 2D upstream and 2D downstream from a
flow disturbance
Simple installation of Compact flowmeters between any existing raised-face flanges
Table 2. Rosemount 2051CFC Compact Flowmeter Ordering Information

2051CFC Compact Flowmeter
Measurement Type
Standard Standard
Primary Element Technology
Standard Standard
A Annubar® Averaging Pitot Tube ★
C Conditioning Orifice Plate ★
P Orifice Plate ★
Material Type
Standard Standard
S 316 SST ★
Line Size
Standard Standard
005(1) 1/2-in. (15 mm) ★
010(1) 1-in. (25 mm) ★
015(1) 11/2-in. (40 mm) ★
020 2-in. (50 mm) ★
030 3-in. (80 mm) ★
040 4-in. (100 mm) ★
060 6-in. (150 mm) ★
080 8-in. (200 mm) ★
100(2)(3) 10-in. (250 mm) ★
120(2)(3) 12-in. (300 mm) ★
Primary Element Type
Standard Standard
N000 Annubar Sensor Size 1 ★
N040 0.40 Beta Ratio ★
N065(4) 0.65 Beta Ratio ★
Temperature Measurement
Standard Standard
0 No Temperature Sensor ★
T(5) Integral RTD ★
Standard Standard
3 Direct-mount ★
7 Remote-mount, NPT Connections ★
www.rosemount.com 9

Differential Pressure Range
Standard Standard
1 0 to 25 in H2O (0 to 62,3 mbar) ★
2 0 to 250 in H2O (0 to 623 mbar) ★
3 0 to 1000 in H2O (0 to 2,5 bar) ★
Transmitter Output
Standard Standard
(6) ★
A 4–20 mA with digital signal based on HART Protocol
F FOUNDATION fieldbus Protocol ★
Expanded
M Low-Power, 1-5Vdc with Digital Signal Based on HART Protocol
Standard Standard
A Aluminum 1
/2-14 NPT ★
J SST 1
/2-14 NPT ★
K(8) SST M20 x 1.5 ★
Expanded
D Aluminum G1/2
M(8) SST G1/2
Standard Standard
1 Up to ±2.00% flow rate accuracy, 5:1 flow turndown, 2-year stability ★

Installation Accessories
Standard Standard
AB ANSI Alignment Ring (150#) (Only required for 10-in. (250 mm) and 12-in. (300mm) line sizes) ★
AC ANSI Alignment Ring (300#) (Only required for 10-in. (250 mm) and 12-in. (300mm) line sizes) ★
AD ANSI Alignment Ring (600#) (Only required for 10-in. (250 mm) and 12-in. (300mm) line sizes) ★
DG DIN Alignment Ring (PN16) ★
DH DIN Alignment Ring (PN40) ★
DJ DIN Alignment Ring (PN100) ★
Expanded
JB JIS Alignment Ring (10K)
JR JIS Alignment Ring (20K)
JS JIS Alignment Ring (40K)
Remote Adapters
Standard Standard
FE Flange Adapters 316 SST (1/2-in NPT) ★
High Temperature Application
Expanded
HT Graphite Valve Packing (Tmax = 850 °F)
Flow Calibration
Expanded
WC(9) Flow Calibration, 3 Pt, Conditioning Orifice Option C (All Pipe Schedules)
WD(10)(11) Flow Calibration, 10 Pt, Conditioning Option C (All Schedules), Annubar Option A (Schedule 40)
10 www.rosemount.com
Pressure Testing
Expanded
P1 Hydrostatic Testing with Certificate
Special Cleaning
Expanded
P2(12) Cleaning for Special Services
Special Inspection
Standard Standard
QC7 Inspection and Performance Certificate ★
Standard Standard
Standard Standard
QS(13) Prior-use certificate of FMEDA data ★
QT(14)(15) Safety certified to IEC 61508 with certificate of FMEDA ★
Standard Standard
Q8 Material Traceability Certification per EN 10204:2004 3.1 ★
Code Conformance
Expanded
J2 ANSI/ASME B31.1
J3 ANSI/ASME B31.3
J4 ANSI/ASME B31.8
Expanded
J5(16) NACE MR-0175 / ISO 15156
Expanded
Standard Standard
www.rosemount.com 11

(17) ★
IE FM FISCO Intrinsically Safe
KB
and I6)
ND(4) ATEX Dust ★
Shipboard Approvals
Standard Standard
Standard Standard
Digital Display
Standard Standard
(19) ★
M5 LCD Display ★
Standard Standard
Manifold for Remote Mount Option
Standard Standard
Alarm Limit
Standard Standard
CR(14)(15) Custom alarm and saturation signal levels, high alarm (requires C1 and Configuration Data Sheet) ★
CS(14)(15) Custom alarm and saturation signal levels, low alarm (requires C1 and Configuration Data Sheet) ★
CT(14)(15) Low alarm (standard Rosemount alarm and saturation levels) ★
Standard Standard
Standard Standard

Ground Screw
Standard Standard
(22) ★
V5 External Ground Screw Assembly
HART Revision Configuration
Standard Standard
HR5(14)(15)(23) Configured for HART Revision 5 ★
HR7(14)(15)(24) Configured for HART Revision 7 ★
Typical Model Number: 2051CFC D C S 060 N 065 0 3 2 A A 1 WC E5 M5
(1) Available with primary element technology P only
(2) For the 10-in. (250 mm) and 12-in. (300 mm) line size, the alignment ring must be ordered (Installation Accessories).
(3) 10-in. (250 mm) and 12-in. (300 mm) line sizes not available with Primary Element Technology A.
(4) For 2-in. (50 mm) line sizes the Primary Element Type is 0.6 for Primary Element Technology Code C.
(5) Available with Primary Element Technology A only.
(6) HART Revision 5 is the default HART output. The Enhanced 3051 can be factory or field configured to HART Revision 7. To order HART Revision 7 factory configured, add
option code HR7.
(7) Material specified is cast as follows: CF-8M is the cast version of 316 SST, CF-3M is the cast version of 316L SST. For housing, material is aluminum with polyurethane paint.
(9) Available with primary element technology C only.
(10) Available with primary element technology C or A only.
(11) For Annubar Option A, consult factory for pipe schedules other than Sch. 40.
(12) Available with primary element technology C or P only
(14) Select Configuration Buttons (option code D4 or DZ) or Local Operator Interface (option code M4) if local configuration buttons are required.
(16) Materials of Construction comply with metallurgical requirements within NACE MR0175/ISO for sour oil field production environments. Environmental limits apply to
certain materials. Consult latest standard for details. Selected materials also conform to NACE MR0103 for sour refining environments.
(19) Not available with FOUNDATION fieldbus (Output Code F).
Rosemount 2051CFP Integral Orifice Flowmeter

Precision honed pipe section for increased accuracy in small line sizes
Self-centering plate design prevents alignment errors that magnify measurement inaccuracies in small line
sizes
Table 3. Rosemount 2051CFP Integral Orifice Flowmeter Ordering Information

2051CFP Integral Orifice Flowmeter
Measurement Type
Standard Standard
Material Type
Standard Standard
S 316 SST ★
Line Size
Standard Standard
005 1
/2-in. (15 mm) ★
010 1-in. (25 mm) ★
015 11/2-in. (40 mm) ★
Process Connection
Standard Standard
T1 NPT Female Body (Not Available with Remote Thermowell and RTD) ★
S1(1) Socket Weld Body (Not Available with Remote Thermowell and RTD) ★
P1 Pipe Ends: NPT Threaded ★
P2 Pipe ends: Beveled ★
D1 Pipe Ends: Flanged, DIN PN16, slip-on ★
W1 Pipe Ends: Flanged, RF, ANSI Class 150, weld-neck ★
A1 Pipe Ends: Flanged, RF, ANSI Class 150, slip-on ★
Expanded
R1 Pipe Ends: Flanged, RTJ, ANSI Class 150, slip-on
Orifice Plate Material
Standard Standard
S 316 SST ★
Bore Size Option
Standard Standard
0066 0.066-in. (1.68 mm) for 1/2-in. Pipe ★
0109 0.109-in. (2.77 mm) for 1/2-in. Pipe ★
0160 0.160-in. (4.06 mm) for 1/2-in. Pipe ★

0196 0.196-in. (4.98 mm) for 1/2-in. Pipe ★
0260 0.260-in. (6.60 mm) for 1/2-in. Pipe ★
0340 0.340-in. (8.64 mm) for 1/2-in. Pipe ★
0150 0.150-in. (3.81 mm) for 1-in. Pipe ★
0250 0.250-in. (6.35 mm) for 1-in. Pipe ★
0345 0.345-in. (8.76 mm) for 1-in. Pipe ★
0500 0.500-in. (12.70 mm) for 1-in. Pipe ★
0630 0.630-in. (16.00 mm) for 1-in. Pipe ★
0800 0.800-in. (20.32 mm) for 1-in. Pipe ★
0295 0.295-in. (7.49 mm) for 1 1/2-in. Pipe ★
0376 0.376-in. (9.55 mm) for 1 1/2-in. Pipe ★
0512 0.512-in. (13.00 mm) for 1 1/2-in. Pipe ★
0748 0.748-in. (19.00 mm) for 1 1/2-in. Pipe ★
1022 1.022-in. (25.96 mm) for 1 1/2-in. Pipe ★
1184 1.184-in. (30.07 mm) for 1 1/2-in. Pipe ★
Expanded
0010 0.010-in. (0.25 mm) for 1/2-in. Pipe
0014 0.014-in. (0.36 mm) for 1/2-in. Pipe
0020 0.020-in. (0.51 mm) for 1/2-in. Pipe
0034 0.034-in. (0.86 mm) for 1/2-in. Pipe
Standard Standard
D3 Direct-mount, 3-Valve Manifold, SST ★
D5 Direct-mount, 5-Valve Manifold, SST ★
R3 Remote-mount, 3-Valve Manifold, SST ★
R5 Remote-mount, 5-Valve Manifold, SST ★
Differential Pressure Ranges
Standard Standard
1 0 to 25 in H2O (0 to 62,3 mbar) ★
2 0 to 250 in H2O (0 to 623 mbar) ★
3 0 to 1000 in H2O (0 to 2,5 bar) ★
Transmitter Output
Standard Standard
A(2) 4–20 mA with digital signal based on HART protocol ★
F FOUNDATION fieldbus protocol ★
Expanded
M Low-Power, 1-5Vdc with Digital Signal Based on HART Protocol
Standard Standard
A Aluminum 1
/2-14 NPT ★
J SST 1/2-14 NPT ★
K(4) SST M20 x 1.5 ★
Expanded
D Aluminum G1/2
M(4) SST G1/2
Standard Standard
1 up to ±2.25% flow rate accuracy, 5:1 flow turndown, 2-year stability ★


Temperature Sensor
Expanded
RT(5) Thermowell and RTD
Optional Connection
Standard Standard
G1 DIN 19213 Transmitter Connection ★
Pressure Testing
Expanded
P1(6) (7) Hydrostatic Testing with Certificate
Special Cleaning
Expanded
P2 Cleaning for Special Services
Material Testing
Expanded
V1 Dye Penetrant Exam
Material Examination
Expanded
V2 Radiographic Examination
Flow Calibration
Expanded
WD(8) Discharge Coefficient Verification
Special Inspection
Standard Standard
QC7 Inspection and Performance Certificate ★
Standard Standard
Q8 Material Traceability Certification per EN 10204:2004 3.1 ★
Code Conformance
Expanded
J2(9) ANSI/ASME B31.1
Expanded
J5(10) NACE MR-0175 / ISO 15156
Standard Standard
J6 European Pressure Directive (PED) ★
Expanded

Standard Standard
Standard Standard
QS(11) Prior-use Certificate of FMEDA data ★
QT(12)(13) Safety certified to IEC 61508 with certificate of FMEDA ★
Standard Standard
IE(14) FM FISCO Intrinsically Safe ★
KB
and I6)
ND(4) ATEX Dust ★
Shipboard Approvals
Standard Standard
Standard Standard
Digital Display
Standard Standard
(16) ★
M5 LCD Display ★

Standard Standard
Alarm Limit
Standard Standard
CR(12)(13) Custom alarm and saturation signal levels, high alarm (requires C1 and Configuration Data Sheet) ★
CS(12)(13) Custom alarm and saturation signal levels, low alarm (requires C1 and Configuration Data Sheet) ★
CT(12)(13) Low alarm (standard Rosemount alarm and saturation levels) ★
Standard Standard
Standard Standard
Ground Screw
Standard Standard
V5(19) External Ground Screw Assembly ★
Standard Standard
HR5(12)(13) ★
(20) Configured for HART Revision 5
HR7(12)(13) ★
(21) Configured for HART Revision 7
Typical Model Number: 2051CFP D S 010 W1 S 0500 D3 2 A A 1 E5 M5
(1) To improve pipe perpendicularity for gasket sealing, socket diameter is smaller than standard pipe O.D.
(2) HART Revision 5 is the default HART output. The Enhanced 3051 can be factory or field configured to HART Revision 7. To order HART Revision 7 factory configured, add
option code HR7.
(3) Material specified is cast as follows: CF-8M is the cast version of 316 SST, CF-3M is the cast version of 316L SST. For housing, material is aluminum with polyurethane
paint.
(5) Thermowell Material is the same as the body material.
(6) Does not apply to Process Connection codes T1 and S1.
(7) Option P1 may not be ordered in combination with P2 or PA.
(8) Not available for bore sizes 0010, 0014, 0020, 0034, 0066, or 0109.
(9) Not available with DIN Process Connection codes D1, D2, or D3.
(10) Materials of Construction comply with metallurgical requirements within NACE MR0175/ISO for sour oil field production environments. Environmental limits apply to
certain materials. Consult latest standard for details. Selected materials also conform to NACE MR0103 for sour refining environments.
(12) Select Configuration Buttons (option code D4 or DZ) or Local Operator Interface (option code M4) if local configuration buttons are required.
(16) Not available with FOUNDATION fieldbus (Output Code F).
2051CF specifications
Rosemount 2051CF performance specifications
Performance assumptions include: measured pipe I.D, transmitter is trimmed for optimum flow accuracy, and performance is
dependent on application parameters.
Table 4. Flow Performance - Flow Reference Accuracy(1)

2051CFA Annubar Flowmeter
Ranges 2-3 ±2.30% of Flow Rate at 5:1 flow turndown
2051SFC_A Compact Annubar Flowmeter - Annubar Option A
Ranges 2-3 Uncalibrated ±2.60% of Flow Rate at 5:1 flow turndown
Calibrated ±2.30% of Flow Rate at 5:1 flow turndown
2051CFC Compact Orifice Flowmeter – Conditioning Option C
 =0.4 ±2.25% of Flow Rate at 5:1 flow turndown
Ranges 2-3
2051CFC Compact Orifice Flowmeter – Orifice Option P(2)
Ranges 2-3
2051CFP Integral Orifice Flowmeter
 <0.1 ±3.10% of Flow Rate at 5:1 flow turndown
0.1<  <0.2 ±2.75% of Flow Rate at 5:1 flow turndown
Ranges 2-3
(1) Range 1 flowmeters may experience an additional uncertainty up to 0.9%. Consult your Emerson Process
Management Representative for exact specifications.
(2) For smaller line sizes, see Rosemount Compact Orifice
Rosemount 2051CF functional Turn-On Time

Performance within specifications less than 20.0
specifications seconds after power is applied to the transmitter.
Range and Sensor Limits FOUNDATION fieldbus Function Block Execution Times
Block Execution Time
Range 2051CF Minimum Span Range and Sensor Limits
Resource -
1 0.5 inH2O (1,24 mbar) 0 to 25 inH2O (62,16 mbar) Transducer -
2 2.5 inH2O (4,14 mbar) 0 to 250 inH2O (0,62 bar) LCD Block -
3 6.67 inH2O (16,58 mbar) 0 to 1000 inH2O (2,49 bar) Analog Input 1, 2 30 milliseconds
PID 45 milliseconds
Service
Liquid, gas, and steam applications FOUNDATION fieldbus Parameters
Schedule Entries 7 (max.)
Protocols Links 20 (max.)
Virtual Communications Relationships (VCR) 12 (max.)
4–20 mA HART (Output Code A)
Output Standard Function Blocks
Two-wire 4–20 mA, user-selectable for linear or square Resource Block
root output. Digital process variable superimposed on
 Contains hardware, electronics, and diagnostic information.
4–20 mA signal, available to any host that conforms to
the HART protocol. Transducer Block
Power Supply
 Contains actual sensor measurement data including the
External power supply required. Standard transmitter
sensor diagnostics and the ability to trim the pressure sensor
operates on 10.5 to 42.4 Vdc with no load.
or recall factory defaults.
Turn-On Time
Performance within specifications less than 2.0 LCD Block
seconds after power is applied to the transmitter.  Configures the local display.
Load Limitations
2 Analog Input Blocks
Maximum loop resistance is determined by the
voltage level of the external power supply, as  Processes the measurements for input into other function
described by: blocks. The output value is in engineering units or custom and
Maximum Loop Resistance = 43.5 * (Power Supply contains a status indicating measurement quality.
Voltage – 10.5) PID Block
1387
 Contains all logic to perform PID control in the field including
Load (Ohms)
1000 cascade and feedforward.

Backup Link Active Scheduler (LAS)
500 Operating The transmitter can function as a Link Active
Region
Scheduler if the current link master device fails or is
0
10.5 20 30 removed from the segment.
Voltage (Vdc) 42.4
1-5 Vdc HART Low Power (Output Code M)
The Field Communicator requires a minimum
loop resistance of 250 for communication. Output
Three wire 1–5 Vdc output, user-selectable for linear
FOUNDATION fieldbus (Output Code F) or square root output. Digital process variable
Power Supply superimposed on voltage signal, available to any host
External power supply required; transmitters operate conforming to the HART protocol.
on 9.0 to 32.0 Vdc transmitter terminal voltage. Power Supply
Current Draw External power supply required. Standard transmitter
17.5 mA for all configurations (including LCD display operates on 9 to 28 Vdc with no load.
option)
Power Consumption
3.0 mA, 27–84 mW
Output Load Pressure and Temperature Limits(1)
Direct Mount Transmitter
100 k or greater
Turn-On Time  Up to 600# ANSI (1440 psig at 100 °F (99 bar at 38 °C))
Performance within specifications less than 2.0
seconds after power is applied to the transmitter.  Integral temperature measurement is not available with
Flanged mounting type greater than class 600
Overpressure Limits
Remote Mount Transmitter
Transmitters withstand the following limits without damage:
 Up to 2500# ANSI (6000 psig at 100 °F (416 bar at 38 °C)).
2051CF Flowmeters
(1) Static pressure selection may effect pressure limitations.
 Ranges 2–5: 3626 psig (250 bar)
4500 psig (310,3 bar) for option code P9
For 2051CFC Temperature Limits-Process Temperature
 Range 1: 2000 psig (137,9 bar) Limits
Static Pressure Limit
 -40 to 450 °F (-40 to 232 °C)
 Operates within specifications between static line pressures
 Up to 400 °F (204 °C) when top mounted in steam service
of -14.2 psig (0.034 bar) and 3626 psig (250 bar)
 Range 1: 0.5 psia to 2000 psig (34 mbar and 137,9 bar)
 -148 to 850 °F (-100 to 454 °C) – Stainless Steel
Burst Pressure Limits
For 2051CFP Temperature Limits-Process Temperature
Limits
2051CF
Standard (direct/remote mount):
 10000 psig (689,5 bar)
 –40 to 450 °F (–40 to 232 °C)
Temperature Limits Extended (remote mount only with option code G):
For 2051CFA Temperature Limits-Process Temperature  –148 to 850 °F (–100 to 454 °C)
Limits
Transmitter Temperature Limits:
 500 °F (260 °C)
Ambient(1)
 750 °F (398 °C) when used with a direct mount, high –40 to 185 °F (–40 to 85 °C)
temperature 5-valve manifold (Transmitter Connection With LCD display(2): –40 to 175 °F (–40 to 80 °C)
Platform code 6). Maximum temperature limit for steam
processes is 650 °F (343 °C). Storage(1)
–50 to 230 °F (–46 to 110 °C)
 400 °F (204 °C) when top mounted in steam service With LCD display: –40 to 185 °F (–40 to 85 °C)
(1) Limits for silicone fill fluid only.
 1250 °F (677 °C) – Alloy C-276 Sensor Material (For
superheated steam applications above 1000 °F (538 °C), it is (2) LCD display may not be readable and LCD updates will be slower at
temperatures below -4 °F (-20 °C).
recommended that the Rosemount 585 with Alloy 800H
sensor material is used.)
 850 °F (454 °C) – Stainless Steel Sensor Material
Process Temperature Limits Failure Mode Alarm

At atmospheric pressures and above. If self-diagnostics detect a sensor or microprocessor failure, the
Table 5. 2051 Process Temperature Limits analog signal is driven either high or low to alert the user. High or
low failure mode is user-selectable with a jumper on the
2051C
transmitter. The values to which the transmitter drives its
Silicone Fill Sensor(1) –40 to 250 °F (–40 to 121 °C) output in failure mode depend on whether it is
Inert Fill Sensor(1) –40 to 185 °F (–40 to 85 °C) factory-configured to standard or NAMUR-compliant operation.
The values for each are as follows:
(1) Process temperatures above 185 °F (85 °C) require derating the ambient
limits by a 1.5:1 ratio.
Standard Operation
Humidity Limits Output Code Linear Output Fail High Fail Low
0–100% relative humidity A 3.9  I  20.8 I  21.75 mA I  3.75 mA
M 0.97  V  5.2 V  5.4 V V  0.95 V
Volumetric Displacement
Less than 0.005 in3 (0,08 cm3) NAMUR-Compliant Operation
Output Code Linear Output Fail High Fail Low
Damping
A 3.8  I  20.5 I  22.5 mA I  3.6 mA
Analog output response to a step input change is user-selectable
from 0 to 25.6 seconds for one time constant. This software
damping is in addition to sensor module response time.
Output Code F
If self-diagnostics detect a gross transmitter failure, that information gets passed as a status along with the process variable.
Long Term Stability
Models Standard Performance Option, P8
2051CF
Range 1 (CF) ±0.2% of URL for 1 year, Reference Stability
Ranges 2-5 ±0.1% of URL for 2 years, Operating Stability ±0.125% of URL for 5 years, Operating Stability
Dynamic Performance
4-20 mA HART(1)
FOUNDATION Typical HART Transmitter Response
1-5 Vdc HART Low
fieldbus(3) Time
Power
Total Response Time (Td + Tc)(2):
Transmitter Output vs. Time
2051CF, Range 3-5: 115 milliseconds 152 milliseconds Pressure Released
Range 1: 270 milliseconds 307 milliseconds
Td = Dead Time
Range 2: 130 milliseconds 152 milliseconds Td Tc
Tc = Time Constant
100%
60 milliseconds Response Time = Td +Tc
Dead Time (Td) 97 milliseconds
(nominal)
63.2% of Total
Update Rate 22 times per second 22 times per second 36.8%
Step Change
0%
(1) Dead time and update rate apply to all models and ranges; analog output only Time
(2) Nominal total response time at 75 °F (24 °C) reference conditions.
(3) Transmitter fieldbus output only, segment macro-cycle not included.
Vibration Effect for 2051CFA, 2051CFC, and amplitude).(1)

2051CFP
Less than ±0.1% of URL when tested per the requirements of
IEC60770-1 field with general application or pipeline with low
vibration level (10-1000 Hz test frequency range, 0.15mm
displacement peak amplitude, 20 m/s2 acceleration
(1) Stainless steel temperature housing is not recommended with primary element technology A in applications with mechanical vibration.
Rosemount 2051CF physical Body
specifications  316 SST (CF8M), material per ASTM A351

Pipe Material (If Applicable)
Electrical Connections
1
/2–14 NPT, G1/2, and M20 × 1.5 conduit.  A312 Gr 316/316L, B622 UNS N10276, Alloy C-276
Flange
2051CF Process-Wetted Parts
 A182 Gr 316/316L, SB-564 UNS N10276, Alloy C-276
For 2051CFA Wetted Parts-Annubar Sensor Material
 Flange pressure limits are per ANSI B16.5
 316 Stainless Steel
 Flange face finish per ANSI B16.5, 125 to 250 RMS
 Alloy C-276
Body Bolts/Studs
For 2051CFC Wetted Parts-Material of Construction
Body/Plate  ASTM A193 Gr B8M studs
 316/316L SST  ASTM A193 Gr B8M Class 2 body studs provided for high
temperature option code G
 50 micro-inch Ra surface finish
Transmitter Connection Studs
Manifold Head/Valves
 ASTM A193 Gr B8M studs
 316 SST
Gaskets/O-rings
Flange Studs and Nuts
 Glass filled PTFE
 Customer supplied
 Inconel® X-750 provided for high temperature option code G
 Available as a spare part
Transmitter Connection Studs and Nuts  Gaskets and O-rings must be replaced each time the 3051SFP
is disassembled for installation or maintenance.
 Studs– A193 Grade B8M.
Process Isolating Diaphragms
 Nuts– A194 Grade 8M. 316L SST, Alloy C-276, or Tantalum
Gasket and O-rings
Non-Wetted Parts for 2051CF
 Gaskets are customer supplied.
Electronics Housing
 Durlon 8500 fiber gaskets are recommended. Consult an Low-copper aluminum or CF-8M (Cast version of 316 SST).
Emerson Process Management representative for use with Enclosure Type 4X, IP 65, IP 66, IP68
other gaskets.
Coplanar Sensor Module Housing
 Available as a spare part CF-3M (Cast version of 316L SST)
Note Bolts
Gaskets and O-rings should be replaced when the 405 is ASTM A449, Type 1 (zinc-cobalt plated carbon steel)
disassembled. ASTM F593G, Condition CW1 (Austenitic 316 SST)
ASTM A193, Grade B7M (zinc plated alloy steel)
For 2051CFP Wetted Parts-Material of Construction
Sensor Module Fill Fluid
Orifice Plate Silicone oil (D.C. 200) or Fluorocarbon oil (Halocarbon or
Fluorinert® FC-43 for 2051T)
 316/316L SST
Paint
 Alloy C-276
Polyurethane
 Alloy 400
Cover O-rings
Nitirile Butadiene (NBR)
Rosemount 2051CF product certifications

Approved manufacturing locations Special Conditions for Safe Use:
Rosemount Inc. — Chanhassen, Minnesota USA 1. The Model 2051 transmitter housing contains
Emerson Process Management GmbH & Co. — Wessling, aluminum and is considered a potential risk of ignition by
Germany impact or friction. Care must be taken into account during
Emerson Process Management Asia Pacific installation and use to prevent impact and friction.
Private Limited — Singapore
2. The Model 2051 transmitter with the transient terminal
Beijing Rosemount Far East Instrument Co., LTD — Beijing, China
block (Option code T1) will not pass the 500Vrms
Emerson Process Management LTDA — Sorocaba, Brazil dielectric strength test and this must be taken into
Emerson Process Management (India) Pvt. Ltd — Daman, India account during installation.
European directive information Canadian Standards Association (CSA)
The EC declaration of conformity for all applicable European directives
for this product can be found on the Rosemount website at All CSA hazardous approved transmitters are certified per
www.rosemount.com. A hard copy may be obtained by contacting an ANSI/ISA 12.27.01-2003.
Emerson Process Management representative.
E6 Explosion-Proof, Dust Ignition Proof
Ordinary Location Certification for Factory Mutual Certificate No: 2041384
As standard, the transmitter has been examined and tested to
Applicable Standards: CSA Std. C22.2 No. 142 - M1987,
determine that the design meets basic electrical, mechanical,
CSA Std. C22.2 No. 30 - M1986, CSA Std. C22.2 No. 213 -
and fire protection requirements by FM, a nationally
M1987, CAN/CSA-E60079-0:07,
recognized testing laboratory (NRTL) as accredited by the
CAN/CSA-E60079-1:07
Federal Occupational Safety and Health Administration
Markings: Explosion-Proof for Class I, Division 1, Groups B,
(OSHA).
C, and D. Dust-Ignition Proof for Class II and Class III,
Division 1, Groups E, F, and G. Suitable for Class I, Division
2051CF HART Protocol 2, Groups A, B, C, and D for indoor and outdoor hazardous
locations. Class I Zone 1 Ex d IIC T5. Enclosure type 4X,
Hazardous Locations Certifications factory sealed. Single Seal.
North American Certifications I6 Intrinsically Safe
Certificate no.: 2041384
FM Approvals Applicable Standards: CSA Std. C22.2 No. 142 - M1987,
E5 Explosion-Proof and Dust-Ignition-Proof CSA Std. C22.2 No. 213 - M1987, CSA Std. C22.2 No. 157 -
Certificate No: 3032938 92, CSA Std. C22.2 No. 213 - M1987, ANSI/ISA 12.27.01 -
Applicable Standards: FM Class 3600 – 1998, FM Class 2003, CAN/CSA-E60079-0:07, CAN/CSA-E60079-11:02
3615 – 2006, FM Class 3810 – 2005, ANSI/NEMA 250 – Markings: Intrinsically safe for Class I, Division 1, Groups A,
1991, ANSI/IEC 60529 – 2004 B, C, and D when connected in accordance with
Markings: Explosion-Proof for Class I, Division 1, Groups B, Rosemount drawings 02051-1008. Temperature code
C, and D T3C. Class I Zone 1 Ex ia IIC T3C. Single Seal. Enclosure Type
Dust-Ignition-Proof for Class II, Division 1, Groups E, F, G; 4X.
and Class III, Division 1. European Certifications
T5 (Ta= -50 °C to +85 °C), Factory Sealed, Enclosure Type
4X I1 ATEX Intrinsic Safety
Certificate No: Baseefa08ATEX0129X
I5 Intrinsically-Safe and Non-incendive
Applicable Standards: EN60079-0:2012,
Certificate No: 3033457
EN60079-11:2012
Applicable Standards: FM Class 3600 – 1998, FM Class
Markings: II 1 G Ex ia IIC T4 Ga(–60 °C  Ta  +70 °C)
3610 – 2007, FM Class 3611 – 2004, FM Class 3810 – 2005
IP66 IP68
Markings: Intrinsically Safe for use in Class I, Division 1,
1180
Groups A, B, C, and D; Class II, Division 1, Groups E, F, and
G; Class III, Division 1; Class I, Zone 0, AEx ia IIC; Table 6. Input Parameters
Nonincendive for use in Class I, Division 2, Groups A, B, C
Ui = 30 V
and D; in accordance with Control Drawing 02051-1009
Ii = 200 mA
T4 (-50 °C to +70 °C) Enclosure Type 4X
For input parameters see control drawing 02051-1009. Pi = 1.0 W
Ci = 0.012 μF
Table 7. RTD Assembly (2051CFx Option T or R) ND ATEX Dust

Certification No. Baseefa08ATEX0182X
Ui = 5 Vdc
Ii = 500 mA Applicable Standards: EN60079-0:2012, EN
Pi =0.63 W 60079-31:2009
Special Conditions for Safe Use (X): Markings: II 1 D Ex t IIIC T50 °C T500 60 °C Da
IP66 IP68
When the optional transient protection terminal block is Ui = 42.4 Vdc
installed, the apparatus is not capable of withstanding the 1180
500 V insulation test required by EN60079-11. This must
be taken into account when installing the apparatus. Special Conditions for Safe Use (X):
If the equipment is fitted with an optional 90 V transient

N1 ATEX Type n suppressor, it is incapable of isolation from earth test and
Certification No. Baseefa08ATEX0130X this must be taken into account during installation.
EN60079-15:2010 IECEx Certifications
Markings: II 3 G I7 IECEx Intrinsic Safety

Ex nA IIC T4 Gc (–40 °C  Ta  +70 °C) Certification No. IECExBAS08.0045X
Ui = 42.4 Vdc max Applicable Standards: IEC60079-0:2011,
IP66 IEC60079-11:2011
Ex ia IIC T4 Ga (–60 °C  Ta  +70 °C)
Special Conditions for Safe Use (X): Table 8. Input Parameters

Ui = 30 V
When the optional transient protection terminal block is
Ii = 200 mA
installed, the apparatus is not capable of withstanding a
500 V r.m.s. test to case. This must be taken into account Pi = 1.0 W
on any installation in which it is used, for example by Ci = 0.012 μF
assuring that the supply to the apparatus is galvanically
isolated.
Table 9. RTD Assembly (2051CFx Option T or R)
Ui = 5 Vdc
E1 ATEX Flame-Proof Ii = 500 mA
Certification No. KEMA 08ATEX0090X Pi = 0.63 W
IEC60079-0:2011, EN60079-1:2007, EN60079-26:2007 Special Conditions for Safe Use (X):
Markings: II 1/2 G
Ex d IIC T6 Ga/Gb (–50 °C  Ta  65 °C) When the optional transient protection terminal block is
Ex d IIC T5 Ga/Gb (–50 °C  Ta  80 °C) installed, the apparatus is not capable of withstanding the
IP66 500V insulation test required by EN60079-11. This must
1180 be taken into account when installing the apparatus.
Ui = 42.4 Vdc E7 IECEx Flame-Proof
Certification No. IECEx KEM 08.0024X
Special Conditions for Safe Use (X):
Applicable Standards: IEC60079-0:2011,
1. Appropriate ex d blanking plugs, cable glands, and IEC60079-1:2007-04, IEC60079-26:2006
wiring needs to be suitable for a temperature of 90 °C.
Ex d IIC T6 Ga/Gb (–50 °C  Ta  65 °C)
2. This device contains a thin wall diaphragm. Installation, Ex d IIC T5 Ga/Gb (–50 °C  Ta  80 °C)
maintenance, and use shall take into account the Ui = 42.4 Vdc
environmental conditions to which the diaphragm will be
subjected. The manufacturer’s instructions for Special Conditions for Safe Use (X):
maintenance shall be followed in detail to assure safety 1. Appropriate ex d blanking plugs, cable glands, and
during its expected lifetime. wiring needs to be suitable for a temperature of 90 °C.
3. In case of repair, Contact Emerson Process Management 2. This device contains a thin wall diaphragm. Installation,
for information on the dimensions of flameproof joints. maintenance, and use shall take into account the
environmental conditions to which the diaphragm will be
subjected. The manufacturer’s instructions for
maintenance shall be followed in detail to assure safety
during its expected lifetime.
3. In case of repair, Contact Emerson Process Management :

for information on the dimensions of flameproof joints. Temperature
Transmitter Model T Code
Range
N7 IECEx Type 'n'
Certification No. IECExBAS08.0046X Using 644 temperature -40 °C Ta +65
T4
Applicable Standards: IEC60079-0: 2011, IEC60079-15: transmitter °C
2010 -50 °C Ta +80
T5
No 644 temperature °C
Ex nA IIC T4 Gc (–40 °C  Ta  +70 °C) transmitter -50 °C Ta +65
Ui = 42.4 Vdc max T6
°C
3. The earth connection facility in the enclosure should be

Special Conditions for Safe Use (X): connected reliably.
When the optional transient protection terminal block is 4. During installation, use and maintenance of the
installed, the apparatus is not capable of withstanding a product, observe the warning “Don’t open the cover when
500 V r.m.s. test to case. This must be taken into account the circuit is alive”.
on any installation in which it is used, for example by
5. During installation, there should be no present mixture
assuring that the supply to the apparatus is galvanically
harmful to the flameproof housing.
isolated.
6. Cable entry and conduit, certified by NEPSI with type of
Inmetro Certifications
protection Ex d IIC and appropriate thread form, should be
E2 Flame-Proof applied when installed in hazardous locations. Blanking
Certificate No: CEPEL 09.1767X elements should be used on the redundant cable entries.
Ex d IIC T* Ga/Gb IP66 7. End users are not permitted to change any internal
T6 = -50 °C  Tamb  65 °C components, but to settle the problem in conjunction with
T5 = -50 °C  Tamb  80 °C the manufacturer to avoid damage to the product.
I2 Intrinsic Safety 8. Maintenance should be done in non-hazardous
Certificate No: CEPEL 09.1768X locations.
Ex ia IIC T4 Ga (–60 °C  Tamb  +70 °C)
IP66 9. During installation, use and maintenance of this
product, observe the following standards:
China (NEPSI) Certifications
GB3836.13-1997 “Electrical apparatus for explosive gas
E3 Flameproof atmospheres Part 13: Repair and overhaul for apparatus
NEPSI Certificate No.: GYJ101321X used in explosive gas atmospheres”
Applicable Standards: GB3836.1-2000, GB3836.2-2000
Markings: Ex d II C T5/T6, GB3836.15-2000 “Electrical apparatus for explosive gas
T5: -50 °C Ta +80 °C atmospheres Part 15: Electrical installations in hazardous
T6: -50 °C Ta +65 °C area (other than mines)”
Specific Conditions for Safe Use (X): GB3836.16-2006 “Electrical apparatus for explosive gas
atmospheres Part 16: Inspection and maintenance of
1. Symbol “X” is used to denote specific conditions of use: electrical installation (other than mines)”
a. The Ex d blanking elements, cable glands and wiring GB50257-1996 “Code for construction and acceptance of
shall be suitable for a temperature of 90°C. electric device for explosion atmospheres and fire hazard
electrical equipment installation engineering”.
b. This device contains a thin wall diaphragm. Installation,
maintenance and use shall take into account the I3 Intrinsic Safety
environmental conditions to which the diaphragm will be NEPSI Certificate No.: GYJ101320X
subjected. Applicable Standards: GB3836.1-2000, GB3836.4-2000
Markings: Ex ia IIC T4
2. The relation between T code and ambient temperature
T4: -60°C Ta +70°C
range is:
Specific Conditions for Safe Use (X):
1. Symbol “X” is used to denote specific conditions of use:
a. If the apparatus is fitted with an optional 90V transient 6. The cables between this product and associated
suppressor, it is not capable of withstanding the 500V apparatus should be shielded cables (the cables must have
insulation test for 1 minute. This must be taken into insulated shields). The shield has to be grounded reliably in
account when installing the apparatus. a non-hazardous area.
2. The relation between T code and ambient temperature 7. End users are not permitted to change any internal
range is: components, but to settle the problem in conjunction with
Temperature the manufacturer to avoid damage to the product.
Transmitter Model T Code
Range
8. During installation, use and maintenance of this
Using 644 temperature product, observe the following standards:
T4 -40 °C Ta +60 °C
transmitter
No 644 No FISCO GB3836.13-1997 “Electrical apparatus for explosive gas
T4 -60 °C Ta +70 °C atmospheres Part 13: Repair and overhaul for apparatus
temperature Version
transmitter FISCO Version T4 -60 °C Ta +60 °C used in explosive gas atmospheres”
3. Intrinsically safe parameters: GB3836.15-2000 “Electrical apparatus for explosive gas

atmospheres Part 15: Electrical installations in hazardous
Maximum
Maximum Maximum Maximum internal area (other than mines)”
Transmitter input input input parameters: GB3836.16-2006 “Electrical apparatus for explosive gas
Model voltage: current: power:
Ci Li atmospheres Part 16: Inspection and maintenance of
Ui (V) Ii (mA) Pi (W)
(nF) (μH) electrical installation (other than mines)”
4-20mA GB50257-1996 “Code for construction and acceptance of
30 200 1 12 0
HART electric device for explosion atmospheres and fire hazard
FOUNDATION electrical equipment installation engineering”.
30 300 1.3 0 0
Fieldbus
Combinations of Certifications
FISCO 17.5 380 5.32 0 0
Stainless steel certification tag is provided when optional
Note approval is specified. Once a device labeled with multiple
FISCO parameters apply to both Group IIC and IIB. approval types is installed, it should not be reinstalled using any
other approval types. Permanently mark the approval label to
When 644 temperature transmitter is used, the 644 distinguish it from unused approval types.
temperature transmitter should be used with Ex-certified
associated apparatus to establish an explosion protection K1 E1, I1, N1, and ND combination
system that can be used in explosive gas atmospheres. K5 E5 and I5 combination
Wiring and terminals should comply with the instruction
manual of both 644 temperature transmitter and K6 I6 and E6 combination
associated apparatus. The cables between 644
K7 E7, I7, and N7 combination
temperature transmitter and associated apparatus should
be shielded cables (the cables must have an insulated KA E1, I1, E6, and I6 combination
shield). The shield has to be grounded reliably in a
KB E5, I5, E6, and I6 combination
non-hazardous area.
KC E1, I1, E5, and I5 combination
4. 2051CF series Flowmeter comply with the requirements KD E1, I1, E5, I5, E6, and I6 combination
for FISCO field devices specified in IEC60079-27:2008. For
the connection of an intrinsically safe circuit in accordance
to the FISCO model, FISCO parameters of 2051CF series
Flowmeter are listed in the table above.
5. The product should be used with Ex-certified associated

apparatus to establish an explosion protection system that
can be used in explosive gas atmospheres. Wiring and
terminals should comply with the instruction manual of
the product and associated apparatus.
2051CF Fieldbus Protocol I6/IF Intrinsically Safe
Certificate no.: 2041384

Hazardous Locations Certifications
Applicable Standards: CSA Std. C22.2 No. 142 - M1987,
North American Certifications CSA Std. C22.2 No. 213 - M1987, CSA Std. C22.2 No. 157 -
92, CSA Std. C22.2 No. 213 - M1987, ANSI/ISA 12.27.01 -
FM Approvals 2003, CAN/CSA-E60079-0:07, CAN/CSA-E60079-11:02
E5 Explosion-Proof and Dust-Ignition-Proof Markings: Intrinsically safe for Class I, Division 1, Groups A,
Certificate No: 3032938 B, C, and D when connected in accordance with
Applicable Standards: FM Class 3600 – 1998, FM Class Rosemount drawings 02051-1008. Temperature code
3615 – 2006, FM Class 3810 – 2005, ANSI/NEMA 250 – T3C. Class I Zone 1 Ex ia IIC T3C. Single Seal. Enclosure Type
1991, ANSI/IEC 60529 – 2004 4X.
Markings: Explosion-Proof for Class I, Division 1, Groups B,
C, and D European Certifications
Dust-Ignition-Proof for Class II, Division 1, Groups E, F, G;
I1 ATEX Intrinsic Safety
and Class III, Division 1.
Certificate No: Baseefa08ATEX0129X
T5 (Ta= -50 °C to +85 °C), Factory Sealed, Enclosure Type
4X
EN60079-11:2012
IE/I5 Intrinsically Safe and Non-incendive Markings: II 1 G Ex ia IIC T4 Ga(–60 °C  Ta  +70 °C)
Certificate No.: 3033457 IP66 IP68
Applicable Standards: FM Class 3600-1998, 1180
FM Class 3610-2007, FM Class 3611-2004, Table 10. Input Parameters
FM Class 3810-2005 Ui = 30 V
Markings: Intrinsically Safe for use in Class I, Division 1, Ii = 300 mA
Groups A, B, C and D; Class II, Division 1, Groups E, F and G; Pi = 1.3 W
Class III, Division 1; Class I, Zone 0, AEx ia IIC; Nonincendive Ci = 0 μF
for use in Class I, Division 2, Groups A, B, C and D; in
accordance with Control Drawing 02051-1009. Table 11. RTD Assembly (2051CFx Option T or R)
Ui = 5 Vdc
For FOUNDATION fieldbus and PROFIBUS PA, Temperature
Code: T4 (Ta = -50 °C to +70 °C) Ii = 500 mA
Pi = 0.63 W
For FISCO,
Temperature Code: T4 (Ta = -50 °C to +60 °C) Special Conditions for Safe Use (X):

Enclosure Type 4X
installed, the apparatus is not capable of withstanding the
For input parameters see control drawing 02051-1009.
500 V insulation test required by EN60079-11. This must
Canadian Standards Association (CSA) be taken into account when installing the apparatus.
All CSA hazardous approved transmitters are certified per IA ATEX FISCO Intrinsic Safety
ANSI/ISA 12.27.01-2003. Certificate No: Baseefa08ATEX0129X
E6 Explosion-Proof, Dust Ignition Proof EN60079-11:2012
Certificate No: 2041384 Markings: II 1 G Ex ia IIC T4 Ga(–60 °C  Ta  +60 °C)
Applicable Standards: CSA Std. C22.2 No. 142 - M1987, IP66 IP68
CSA Std. C22.2 No. 30 - M1986, CSA Std. C22.2 No. 213 - 1180
M1987, CAN/CSA-E60079-0:07,
CAN/CSA-E60079-1:07 Table 12. Input Parameters
Markings: Explosion-Proof for Class I, Division 1, Groups B, Ui = 30 V
C, and D. Dust-Ignitions Proof for Class II and Class III, Ii = 200 mA
Division 1, Groups E, F, and G. Suitable for Class I, Division Pi = 1.0 W
2, Groups A, B, C, and D for indoor and outdoor hazardous Ci =  0.012 μF
locations. Class I Zone 1 Ex d IIC T5. Enclosure type 4X,
factory sealed. Single Seal.
Table 13. RTD Assembly (2051CFx Option T or R) ND ATEX Dust

Certification No. Baseefa08ATEX0182X
Ui = 5 Vdc
Applicable Standards: EN60079-0:2012, EN
Ii = 500 mA
60079-31:2009
Pi = 0.63 W Markings: II 1 D Ex t IIIC T50 °C T500 60 °C Da
IP66 IP68
Ui = 42.4 Vdc
When the optional transient protection terminal block is 1180
installed, the apparatus is not capable of withstanding the
500 V insulation test required by EN60079-11. This must Special Conditions for Safe Use (X):
be taken into account when installing the apparatus.
If the equipment is fitted with an optional 90 V transient
N1 ATEX Type n suppressor, it is incapable of isolation from earth test and
Certification No. Baseefa08ATEX0130X this must be taken into account during installation.
EN60079-15:2010
IECEx Certifications
Markings: II 3 G
Ex nA IIC T4 Gc (–40 °C  Ta  +70 °C) I7 IECEx Intrinsic Safety
Ui = 42.4 Vdc max Certification No. IECExBAS08.0045X
IP66 Applicable Standards: IEC60079-0:2011,
IEC60079-11:2011
Special Conditions for Safe Use (X): Ex ia IIC T4 Ga (–60 °C  Ta  +70 °C)
installed, the apparatus is not capable of withstanding a Table 14. Input Parameters
500 V r.m.s. test to case. This must be taken into account Ui = 30 V
on any installation in which it is used, for example by Ii = 300 mA
assuring that the supply to the apparatus is galvanically Pi = 1.3 W
isolated. Ci = 0 μF
E1 ATEX Flame-Proof Table 15. RTD Assembly (2051CFx Option T or R)
Certification No. KEMA 08ATEX0090X
Ui = 5 Vdc
IEC60079-0:2011, EN60079-1:2007, EN60079-26:2007 Ii = 500 mA
Markings: II 1/2 G Pi = 0.63 W
IP66 The device is not capable of withstanding the 500 V
1180 insulation test required by IEC60079-11. This must be
Ui = 32 Vdc taken into account when installing the apparatus.

IG IECEx FISCO Intrinsic Safety
1. Appropriate ex d blanking plugs, cable glands, and Certification No. IECExBAS08.0045X
wiring needs to be suitable for a temperature of 90 °C. Applicable Standards: IEC60079-0:2011,
2. This device contains a thin wall diaphragm. Installation, IEC60079-11:2011
maintenance, and use shall take into account the Ex ia IIC T4 Ga (-60 °C  Ta  +60 °C)
environmental conditions to which the diaphragm will be IP66
subjected. The manufacturer’s instructions for 1180
maintenance shall be followed in detail to assure safety Table 16. Input Parameters
during its expected lifetime. Ui = 17.5 V
3. In case of repair, Contact Emerson Process Management Ii = 380 mA
for information on the dimensions of flameproof joints. Pi = 5.32 W
Ci =  5 μF
Li = 10 μH
Table 17. RTD Assembly (2051CFx Option T or R) IB FISCO Intrinsic Safety

Certificate No: CEPEL 09.1768X
Ui = 5 Vdc
Ex ia IIC T4 Ga (–60 °C  Tamb  60 °C)
Ii = 500 mA
IP66
Pi = 0.63 W
China (NEPSI) Certifications
E3 Flameproof
The device is not capable of withstanding the 500 V NEPSI Certificate No.: GYJ101321X
insulation test required by IEC 60079-11. This must be Applicable Standards: GB3836.1-2000, GB3836.2-2000
taken into account when installing the apparatus. Markings: Ex d II C T5/T6,
E7 IECEx Flame-Proof T5: -50 °C Ta +80 °C
Certification No. IECEx KEM 08.0024X T6: -50 °C Ta +65 °C
Applicable Standards: IEC60079-0:2011,
IEC60079-1:2007-04, IEC60079-26:2006
Ex d IIC T6 Ga/Gb (–50 °C  Ta  65 °C) 1. Symbol “X” is used to denote specific conditions of use:
Ui = 32 Vdc a. The Ex d blanking elements, cable glands and wiring
shall be suitable for a temperature of 90°C.
b. This device contains a thin wall diaphragm. Installation,
1. Appropriate ex d blanking plugs, cable glands, and maintenance and use shall take into account the
wiring needs to be suitable for a temperature of 90 °C. environmental conditions to which the diaphragm will be
subjected.
2. This device contains a thin wall diaphragm. Installation,
maintenance, and use shall take into account the 2. The relation between T code and ambient temperature
environmental conditions to which the diaphragm will be range is
subjected. The manufacturer’s instructions for :
maintenance shall be followed in detail to assure safety
Transmitter Model T Code Temperature Range
during its expected lifetime.
Using 644 temperature
T4 -40 °C Ta +65 °C
3. In case of repair, Contact Emerson Process Management transmitter
for information on the dimensions of flameproof joints. No 644 temperature T5 -50 °C Ta +80 °C
transmitter T6 -50 °C Ta +65 °C
N7 IECEx Type 'n'
Certification No. IECExBAS08.0046X 3. The earth connection facility in the enclosure should be
Applicable Standards: IEC60079-0: 2011, IEC60079-15: connected reliably.
2010
Ex nA IIC T4 Gc (–40 °C  Ta  +70 °C) 4. During installation, use and maintenance of the
Ui = 42.4 Vdc max product, observe the warning “Don’t open the cover when
the circuit is alive”.
5. During installation, there should be no present mixture
The device is not capable of withstanding the 500 V harmful to the flameproof housing.
insulation test required by IEC60079-15. This must be
6. Cable entry and conduit, certified by NEPSI with type of
taken into account when installing the device.
protection Ex d IIC and appropriate thread form, should be
Inmetro Certifications applied when installed in hazardous locations. Blanking
elements should be used on the redundant cable entries.
E2 Flameproof
Certificate No: CEPEL 09.1767X 7. End users are not permitted to change any internal
Ex d IIC T* Ga/Gb IP66 components, but to settle the problem in conjunction with
T6 = -50 °C < Tamb < 65 °C the manufacturer to avoid damage to the product.
T5 = -50 °C < Tamb < 80 °C
8. Maintenance should be done in non-hazardous
I2 Intrinsic Safety locations.
Certificate No: CEPEL 09.1768X
Ex ia IIC T4 Ga (–60 °C  Tamb  70 °C)
IP66

atmospheres Part 13: Repair and overhaul for apparatus Note
used in explosive gas atmospheres” FISCO parameters apply to both Group IIC and IIB.
GB3836.15-2000 “Electrical apparatus for explosive gas When 644 temperature transmitter is used, the 644
atmospheres Part 15: Electrical installations in hazardous
temperature transmitter should be used with Ex-certified
area (other than mines)”
associated apparatus to establish an explosion protection
GB3836.16-2006 “Electrical apparatus for explosive gas system that can be used in explosive gas atmospheres.
atmospheres Part 16: Inspection and maintenance of Wiring and terminals should comply with the instruction
electrical installation (other than mines)” manual of both 644 temperature transmitter and
associated apparatus. The cables between 644
GB50257-1996 “Code for construction and acceptance of
temperature transmitter and associated apparatus should
electric device for explosion atmospheres and fire hazard
be shielded cables (the cables must have an insulated
shield). The shield has to be grounded reliably in a
I3 Intrinsic Safety non-hazardous area.
NEPSI Certificate No.: GYJ101320X
Applicable Standards: GB3836.1-2000, GB3836.4-2000 4. 2051CF series Flowmeter comply with the requirements
Markings: Ex ia IIC T4 for FISCO field devices specified in IEC60079-27:2008. For
T4: -60°C Ta +70°C the connection of an intrinsically safe circuit in accordance
T4: -60°C Ta +60°C (FISCO) to the FISCO model, FISCO parameters of 2051CF series
Specific Conditions for Safe Use (X): Flowmeter are listed in the table above.
1. Symbol “X” is used to denote specific conditions of use: 5. The product should be used with Ex-certified associated
a. If the apparatus is fitted with an optional 90V transient apparatus to establish an explosion protection system that
suppressor, it is not capable of withstanding the 500V can be used in explosive gas atmospheres. Wiring and
insulation test for 1 minute. This must be taken into terminals should comply with the instruction manual of
account when installing the apparatus.
the product and associated apparatus.
2. The relation between T code and ambient temperature range
is: 6. The cables between this product and associated
Transmitter Model T Code Temperature Range apparatus should be shielded cables (the cables must have
Using 644 temperature T4 -40 °C ≤ Ta ≤ +60 °C
insulated shields). The shield has to be grounded reliably in
transmitter a non-hazardous area.
No 644 No FISCO T4 -60 °C ≤ Ta ≤ +70 °C
7. End users are not permitted to change any internal
temperature Version
transmitter
components, but to settle the problem in conjunction with
FISCO Version T4 -60 °C ≤ Ta ≤ +60 °C
the manufacturer to avoid damage to the product.
3. Intrinsically safe parameters:
Maximum Maximum Maximu Maximum
Transmitter input input m input internal
Model voltage: current: power: parameters: GB3836.13-1997 “Electrical apparatus for explosive gas
Ui (V) Ii (mA) Pi (W) Ci (nF) Li (μH) atmospheres Part 13: Repair and overhaul for apparatus
used in explosive gas atmospheres”
4-20mA
30 200 1 12 0
HART GB3836.15-2000 “Electrical apparatus for explosive gas
FOUNDATION atmospheres Part 15: Electrical installations in hazardous
30 300 1.3 0 0
Fieldbus area (other than mines)”
FISCO 17.5 380 5.32 0 0
atmospheres Part 16: Inspection and maintenance of
electrical installation (other than mines)”
GB50257-1996 “Code for construction and acceptance of

electric device for explosion atmospheres and fire hazard
Combinations of Certifications
Stainless steel certification tag is provided when optional

approval is specified. Once a device labeled with multiple
approval types is installed, it should not be reinstalled
using any other approval types. Permanently mark the
approval label to distinguish it from unused approval
types.
K1 E1, I1, N1, and ND combination
K5 E5 and I5 combination
K6 I6 and E6 combination
K7 E7, I7, and N7 combination
KA E1, I1, E6, and I6 combination
KB E5, I5, E6, and I6 combination
KC E1, I1, E5, and I5 combination
KD E1, I1, E5, I5, E6, and I6 combination
Pipe I.D. Range Code

For pipes with an Inner Diameter (I.D.) Range / Pipe Wall Thickness not found in this table or with a line size greater than 12-in. (300
mm), choose option code Z and specify the exact pipe dimensions (I.D. and Pipe Wall Thickness) on the Configuration Data Sheet
(See document 00806-0100-4010). The Emerson process Management sizing program will determine this code, based on the
application piping.
Line Size Pipe Wall Thickness I.D.

Max. Option Inner Diameter (I.D.) Range Range
Nominal ANSI Pipes Non-ANSI Pipes Code
O.D. Code
1.784 to 1.841-in. (45.31 to 46.76 0.065 to 0.488-in. (1.7 to
A
mm) 12.4 mm)
1.842 to 1.938-in. (46.79 to 49.23 0.065 to 0.449-in. (1.7 to
0.065 to B
2-in. 2.625-in. mm) 11.4 mm)
020 0.545-in.
(50 mm) (66.68 mm) 1.939 to 2.067-in. (49.25 to 52.50 0.065 to 0.417-in. (1.7 to
(1.7 to 13.8 mm) C
mm) 10.6 mm)
2.068 to 2.206-in. (52.53 to 56.03 0.065 to 0.407-in. (1.7 to
D
mm) 10.3 mm)
2.207 to 2.322-in. (56.06 to 58.98 0.083 to 0.448-in. (2.1 to
B
mm) 11.4 mm)
2.323 to 2.469-in. (59.00 to 62.71 0.083 to 0.417-in. (2.1 to
21/2-in. 0.083 to C
3.188-in. mm) 10.6 mm)
(63.5 025 0.563-in.
(80.98 mm) 2.470 to 2.598-in. (62.74 to 65.99 0.083 to 0.435-in. (2.1 to
mm) (2.1 to 14.3 mm) D
mm) 11.0 mm)
2.599 to 2.647-in. (66.01 to 67.23 0.083 to 0.515-in. (2.1 to
E
mm) 13.1 mm)
2.648 to 2.751-in. (67.26 to 69.88 0.083 to 0.460-in. (2.1 to
A
mm) 11.7 mm)
2.752 to 2.899-in. (69.90 to 73.63 0.083 to 0.416-in. (2.1 to
0.083 to B
3-in. 3.75-in. mm) 10.6 mm)
030 0.563-in.
(80 mm) (95.25 mm) 2.900 to 3.068-in. (73.66 to 77.93 0.083 to 0.395-in. (2.1 to
(2.1 to 14.3 mm) C
mm) 10.0 mm)
3.069 to 3.228-in. (77.95 to 81.99 0.083 to 0.404-in (2.1 to 10.3
D
mm) mm)
3.229 to 3.333-in. (82.02 to 84.66 0.120 to 0.496-in. (3.0 to
B
mm) 12.6 mm)
0.120 to
31/2-in. 4.25-in. 3.334 to 3.548-in. (84.68 to 90.12 0.120 to 0.386-in. (3.0 to 9.8
035 0.600-in. C
(89 mm) (107.95 mm) mm) mm)
(3.0 to 15.2 mm)
3.549 to 3.734-in. (90.14 to 94.84 0.120 to 0.415-in. (3.0 to
D
mm) 10.5 mm)
3.735 to 3.825-in. (94.87 to 97.16 0.120 to 0.510-in. (3.0 to
B
mm) 13.0 mm)
3.826 to 4.026-in. (97.18 to 102.26 0.120 to 0.400-in. (3.0 to
4-in. 0.120 to C
5.032-in. mm) 10.2 mm)
(100 040 0.600-in.
(127.81 mm) 4.027 to 4.237-in. (102.29 to 0.120 to 0.390-in. (3.0 to 9.9
mm) (3.0 to 15.2 mm) D
107.62 mm) mm)
4.238 to 4.437-in. (107.65 to 0.120 to 0.401-in. (3.0 to
E
112.70 mm) 10.2 mm)
4.438 to 4.571-in. (112.73 to 0.134 to 0.481-in. (3.4 to
A
116.10 mm) 12.2 mm)
4.572 to 4.812-in. (116.13 to 0.134 to 0.374-in. (3.4 to 9.5
5-in. 0.134 to B
6.094-in. 122.22 mm) mm)
(125 050 0.614-in.
(154.79 mm) 4.813 to 5.047-in. (122.25 to 0.134 to 0.380-in. (3.4 to 9.7
mm) (3.4 to 15.6 mm) C
128.19 mm) mm)
5.048 to 5.249-in. (128.22 to 0.134 to 0.413-in. (3.4 to
D
133.32 mm) 10.5 mm)
5.250 to 5.472-in. (133.35 to 0.134 to 0.3919-in. (3.4 to

A
138.99 mm) 9.9 mm)
5.473 to 5.760-in. (139.01 to 0.134 to 0.327-in. (3.4 to 8.3
6-in. 0.134 to B
Sensor
Size 1
6.93-in. 146.30 mm) mm)

(150 060 0.614-in.
(176.02 mm) 5.761 to 6.065-in. (146.33 to 0.134 to 0.31-in. (3.4 to 7.9
mm) (3.4 to 15.6 mm) C
154.05 mm) mm)
6.066 to 6.383-in. (154.08 to 0.134 to 0.297-in. (3.4 to 7.5
D
162.13 mm) mm)
5.250 to 5.472-in. (133.35 to 0.134 to 1.132-in. (3.4 to
A
139.99 mm) 28.7 mm)
5.473 to 5.760-in. (139.01 to 0.134 to 1.067-in. (3.4 to
6-in. 0.134 to B
Sensor
Size 2
6.93-in. 146.30 mm) 27.1 mm)

(150 060 1.354-in.
(176.02 mm) 5.761 to 6.065-in. (146.33 to 0.134 to 1.05-in. (3.4 to 26.7
mm) (3.4 to 34.4 mm) C
154.05 mm) mm)
6.066 to 6.383-in. (154.08 to 0.134 to 1.037-in. (3.4 to
D
162.13 mm) 26.3 mm)
6.384 to 6.624-in. (162.15 to 0.134 to 0.374-in. (3.4 to 9.5
B
168.25 mm) mm)
7-in. 0.134 to
Sensor
Size 1
7.93-in. 6.625 to 7.023-in. (168.28 to 0.134 to 0.216-in. (3.4 to 5.5

(180 070 0.614-in. C
(201.42 mm) 178.38 mm) mm)
mm) (3.4 to 15.6 mm)
7.024 to 7.392-in. (178.41 to 0.134 to 0.246-in. (3.4 to 6.2
D
187.76 mm) mm)
6.384 to 6.624-in. (162.15 to 0.134 to 1.114-in. (3.4 to
B
168.25 mm) 28.3 mm)
7-in. 0.134 to
Sensor
Size 2
7.93-in. 6.625 to 7.023-in. (168.28 to 0.134 to 0.956-in. (3.4 to

(180 070 1.354-in. C
(201.42 mm) 178.38 mm) 24.3 mm)
mm) (3.4 to 34.4 mm)
7.024 to 7.392-in. (178.41 to 0.134 to 0.986-in. (3.4 to
D
187.76 mm) 25.0 mm)
7.393 to 7.624-in. (187.78 to 0.250 to 0.499-in. (6.4 to
B
193.65 mm) 12.6 mm)
7.625 to 7.981-in. (193.68 to 0.250 to 0.374-in. (6.4 to 9.5
8-in. C
Sensor
Size 1
9.688-in. 202.72 mm) 0.250 to 0.73-in. mm)

(200 080
(246.08 mm) 7.982 to 8.400-in. (202.74 to (6.4 to 18.5 mm) 0.250 to 0.312-in. (6.4 to 7.9
mm) D
213.36 mm) mm)
8.401 to 8.766-in. (213.39 to 0.250 to 0.364-in. (6.4 to 9.2
E
222.66 mm) mm)
7.393 to 7.624-in. (187.78 to 0.250 to 1.239-in. (6.4 to
B
193.65 mm) 31.4 mm)
7.625 to 7.981-in. (193.68 to 0.250 to 1.114-in. (6.4 to
8-in. C
Sensor
Size 2
9.688-in. 202.72 mm) 0.250 to 1.47-in. 28.3 mm)

(200 080
(246.08 mm) 7.982 to 8.400-in. (202.74 to (6.4 to 37.3 mm) 0.250 to 1.052-in. (6.4 to
mm) D
213.36 mm) 26.7 mm)
8.401 to 8.766-in. (213.39 to 0.250 to 1.104-in. (6.4 to
E
222.66 mm) 28.0 mm)
8.767 to 9.172-in. (222.68 to 0.250 to 1.065-in. (6.4 to

A
232.97 mm) 27.1 mm)
9.173 to 9.561-in. (232.99 to 0.250 to 1.082-in. (6.4 to
B
242.85 mm) 27.5 mm)
10-in. 0.250 to
11.75-in. 9.562 to 10.020-in. (242.87 to 0.250 to 1.012-in. (6.4 to
(250 100 1.470-in. C
(298.45 mm) 254.51 mm) 25.7 mm)
mm) (6.4 to 37.3 mm)
10.021 to 10.546-in. (254.53 to 0.250 to 0.945-in. (6.4 to
D
267.87 mm) 24.0 mm)
10.547 to 10.999-in. (267.89 to 0.250 to 1.018-in. (6.4 to
E
279.37 mm) 25.9 mm)
11.000 to 11.373-in. (279.40 to 0.250 to 1.097-in. (6.4 to
B
288.87 mm) 27.9 mm)
12-in. 0.250 to
13.0375-in. 11.374 to 11.938-in. (288.90 to 0.250 to 0.906-in. (6.4 to
(300 120 1.470-in. C
(331.15 mm) 303.23 mm) 23.0 mm)
mm) (6.4 to 37.3 mm)
11.939 to 12.250-in. (303.25 to 0.250 to 1.159-in. (6.4 to
D
311.15 mm) 29.4 mm)
Dimensional drawings
Rosemount 2051CFA Pak-Lok Annubar Flowmeter(1)
Front View Side View Top View
B
C
(1) The Pak-Lok Annubar model is available up to 600# ANSI (1440 psig at 100 °F (99 bar at 38 °C)).
Table 18. 2051CFA Pak-Lok Annubar Dimensional Data

Sensor Size A (Max) B (Max) C (Max) D (Max)
1 8.50 (215.9) 14.55 (369.6) 9.00 (228.6) 6.00 (152.4)
2 11.00 (279.4) 16.30 (414.0) 9.00 (228.6) 6.00 (152.4)
3 12.00 (304.8) 19.05 (483.9) 9.00 (228.6) 6.00 (152.4)
Dimensions are in inches (millimeters)
Rosemount 2051CFA Flanged with Opposite Side Support Annubar Flowmeter

Front View Side View Top View
D
B
Table 19. 2051CFA Flanged Annubar Dimensional Data

Flange Size and A ± 0.125 B ± 0.25 C ± 0.25
Sensor Size D (Max) E (Max) F (Max)
Rating (3.2) (6.4) (6.4)
1 11/2 – 150# 3.88 (98.6) 11.00 (279.4) 18.03 (458.0) 9.00 (228.6) 6.30 (160.0) 3.50 (88.9)
1 11/2 – 300# 4.13 (104.9) 11.00 (279.4) 18.03 (458.0) 9.00 (228.6) 6.86 (174.2) 3.50 (88.9)
1 11/2 – 600# 4.44 (112.8) 11.00 (279.4) 18.03 (458.0) 9.00 (228.6) 6.86 (174.2) 3.50 (88.9)
1 DN40/PN16 3.09 (78.5) 11.00 (279.4) 18.03 (458.0) 9.00 (228.6) 6.30 (160.0) 3.50 (88.9)
1 DN40/PN40 3.21 (81.5) 11.00 (279.4) 18.03 (458.0) 9.00 (228.6) 6.86 (174.2) 3.50 (88.9)
1 DN40/ PN100 3.88 (98.6) 11.00 (279.4) 18.03 (458.0) 9.00 (228.6) 6.86 (174.2) 3.50 (88.9)
1 11/2 – 900# 4.94 (125.5) 9.31 (236.5) - - - 3.50 (88.9)
1 11/2 – 1500# 4.94 (125.5) 9.31 (236.5) - - - 3.50 (88.9)
1 11/2 – 2500# 6.76 (171.7) 11.63 (295.4) - - - 4.00 (101.6)
2 2 – 150# 4.13 (104.9) 12.00 (304.8) 19.03 (483.4) 9.00 (228.6) 6.30 (160.0) 5.00 (127.0)
2 2 – 300# 4.38 (111.3) 12.00 (304.8) 19.03 (483.4) 9.00 (228.6) 6.86 (174.2) 5.00 (127.0)
2 2 – 600# 4.75 (120.7) 12.00 (304.8) 19.03 (483.4) 9.00 (228.6) 6.86 (174.2) 5.00 (127.0)
2 DN50/PN16 3.40 (86.4) 12.00 (304.8) 19.03 (483.4) 9.00 (228.6) 6.30 (160.0) 5.00 (127.0)
2 DN50/PN40 3.52 (89.4) 12.00 (304.8) 19.03 (483.4) 9.00 (228.6) 6.86 (174.2) 5.00 (127.0)
2 DN50/ PN100 4.30 (109.2) 12.00 (304.8) 19.03 (483.4) 9.00 (228.6) 6.86 (174.2) 5.00 (127.0)
2 2 – 900# 5.88 (149.4) 10.50 (266.7) - - - 5.00 (127.0)
2 2 – 1500# 5.88 (149.4) 10.50 (266.7) - - - 5.00 (127.0)
2 2 – 2500# 9.88 (251.0) 15.63 (397.0) - - - 4.50 (114.3)
3 3 – 150# 4.63 (117.6) 13.50 (342.9) 20.53 (521.5) 9.00 (228.6) 6.30 (160.0) 4.00 (101.6)
3 3 – 300# 5.00 (127.0) 13.50 (342.9) 20.53 (521.5) 9.00 (228.6) 6.86 (174.2) 4.00 (101.6)
3 3 – 600# 5.38 (136.7) 13.50 (342.9) 20.53 (521.5) 9.00 (228.6) 6.86 (174.2) 4.00 (101.6)
3 DN80/PN16 3.85 (97.8) 13.50 (342.9) 20.53 (521.5) 9.00 (228.6) 6.30 (160.0) 4.00 (101.6)
3 DN80/PN40 4.16 (105.7) 13.50 (342.9) 20.53 (521.5) 9.00 (228.6) 6.86 (174.2) 4.00 (101.6)
3 DN80/ PN100 4.95 (125.7) 13.50 (342.9) 20.53 (521.5) 9.00 (228.6) 6.86 (174.2) 4.00 (101.6)
3 3 – 900# 8.19 (208.0) 13.06 (331.7) - - - 7.00 (177.8)
3 3 – 1500# 8.56 (217.4) 13.81 (350.8) - - - 7.00 (177.8)
3 3 – 2500# 11.19 (284.2) 17.31 (439.7) - - - 7.00 (177.8)
Dimensions are in inches (millimeters)
Rosemount 2051CFC Compact Flowmeter

Side View Front View Top View
(Primary Element Type code C, P, and A)
Compact Flowmeter
Table 20. 2051CFC Compact Dimensional Data(1)

Primary Transmitter
A B C D
Element Type Height
7.75 (197) - closed 6.00 (152) - closed
Type A 5.62 (143) Transmitter Height + A 7.03 (179)
8.25 (210) - open 6.25 (159) - open
7.75 (197) - closed 6.00 (152) - closed
Type P and C 5.62 (143) Transmitter Height + A 6.20 (157)
8.25 (210) - open 6.25 (159) - open
(1) Measurement in inches (millimeters).
Rosemount 2051CFP Integral Orifice Flowmeter

Side View
Bottom View Front View
Dimensions are in inches (millimeters).
Table 21. 2051CFP Integral Orifice Dimensional Data

Line Size
Dimension 1/2-in. (15 mm) 1-in. (25 mm) 11/2-in. (40 mm)
J (Beveled/Threaded pipe ends) 12.54 (318.4) 20.24 (514.0) 28.44 (722.4)
J (RF slip-on, RTJ slip-on, RF-DIN slip on) 12.62 (320.4) 20.32 (516.0) 28.52 (724.4)
J (RF 150#, weld neck) 14.37 (364.9) 22.37 (568.1) 30.82 (782.9)
J (RF 300#, weld neck) 14.56 (369.8) 22.63 (574.7) 31.06 (789.0)
J (RF 600#, weld neck) 14.81 (376.0) 22.88 (581.0) 31.38 (797.1)
K (Beveled/Threaded pipe ends) 5.74 (145.7) 8.75 (222.2) 11.91 (302.6)
K (RF slip-on, RTJ slip-on, RF-DIN slip on)(1) 5.82 (147.8) 8.83 (224.2) 11.99 (304.6)
K (RF 150#, weld neck) 7.57 (192.3) 10.88 (276.3) 14.29 (363.1)
K (RF 300#, weld neck) 7.76 (197.1) 11.14 (282.9) 14.53 (369.2)
K (RF 600#, weld neck) 8.01 (203.4) 11.39 (289.2) 14.85 (377.2)
B.D. (Bore Diameter) 0.664 (16.87) 1.097 (27.86) 1.567 (39.80)
Dimensions are in inches (millimeters).
(1) Downstream length shown here includes plate thickness of 0.162-in. (4.11 mm).
Rosemount DP Flow Product Data Sheet
00813-0100-4485 Rev EC June 2013
Emerson Process Management Emerson Process Management

Rosemount Inc. Blegistrasse 23
8200 Market Boulevard P.O. Box 1046
Chanhassen, MN 55317 USA CH 6341 Baar
T (U.S.) 1-800-999-9307 Switzerland
T (International) (952) 906-8888 T +41 (0) 41 768 6111
F (952) 906-8889 F +41 (0) 41 768 6300
www.rosemount.com www.rosemount.com
Emerson Process Management Emerson Process Management

Asia Pacific Pte Ltd Latin America
1 Pandan Crescent 1300 Concord Terrace, Suite 400
Signapore 128461 Sunrise Florida 33323 USA
T +65 6777 8211 T + 1 954 846 5030
F +65 6777 0947 www.rosemount.com
Service Support Hotline: +65 6770 8711
Email: [email protected]
www.rosemount.com
Standard Terms and Conditions of Sale can be found at www.rosemount.com\terms_of_sale

The Emerson logo is a trade mark and service mark of Emerson Electric Co.
Rosemount and the Rosemount logotype are registered trademarks of Rosemount Inc.
PlantWeb is a registered trademark of one of the Emerson Process Management group of companies.
HART and WirelessHART are registered trademarks of the HART Communication Foundation
Modbus is a trademark of Modicon, Inc.
All other marks are the property of their respective owners.
© 2013 Rosemount Inc. All rights reserved.

Flowmeter 2051CF

Uploaded by

Copyright:

Available Formats

Flowmeter 2051CF

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Flowmeter 2051CF

Uploaded by

Copyright:

Available Formats

Product Data Sheet

Rosemount 2051CF DP Flowmeters

 Up to 2.00% volumetric flow accuracy at 5:1 turndown

 Available with HART and FOUNDATION fieldbus Protocols

 Aluminum and SST housings available

 4-20mA HART, FOUNDATION fieldbus, Low Power HART

Rosemount 2051CF Flowmeter Series

Rosemount 2051CFA Annubar Flowmeter

Table 1. Rosemount 2051CFA Annubar Flowmeter Ordering Information

Table 1. Rosemount 2051CFA Annubar Flowmeter Ordering Information

Table 1. Rosemount 2051CFA Annubar Flowmeter Ordering Information

Options (Include with selected model number)

Table 1. Rosemount 2051CFA Annubar Flowmeter Ordering Information

Table 1. Rosemount 2051CFA Annubar Flowmeter Ordering Information

Table 1. Rosemount 2051CFA Annubar Flowmeter Ordering Information

(4) Not available with Low Power Output Code M.

(5) Applies to assembled flowmeter only, mounting not tested.

(8) Only valid with FOUNDATION fieldbus Output Code F.

(9) Not available with Output Protocol code F.

Rosemount 2051CFC Compact Flowmeter

Simple installation of Compact flowmeters between any existing raised-face flanges

Table 2. Rosemount 2051CFC Compact Flowmeter Ordering Information

Table 2. Rosemount 2051CFC Compact Flowmeter Ordering Information

Options (Include with selected model number)

Table 2. Rosemount 2051CFC Compact Flowmeter Ordering Information

Table 2. Rosemount 2051CFC Compact Flowmeter Ordering Information

(1) Available with primary element technology P only

(5) Available with Primary Element Technology A only.

(8) Not available with Low Power Output Code M.

(9) Available with primary element technology C only.

(10) Available with primary element technology C or A only.

(12) Available with primary element technology C or P only

(13) Not available with Output Protocol code F.

(17) Only valid with FOUNDATION fieldbus Output Code F.

(19) Not available with FOUNDATION fieldbus (Output Code F).

Rosemount 2051CFP Integral Orifice Flowmeter

Table 3. Rosemount 2051CFP Integral Orifice Flowmeter Ordering Information

Table 3. Rosemount 2051CFP Integral Orifice Flowmeter Ordering Information

Table 3. Rosemount 2051CFP Integral Orifice Flowmeter Ordering Information

Options (Include with selected model number)

Table 3. Rosemount 2051CFP Integral Orifice Flowmeter Ordering Information

Table 3. Rosemount 2051CFP Integral Orifice Flowmeter Ordering Information

Typical Model Number: 2051CFP D S 010 W1 S 0500 D3 2 A A 1 E5 M5

(4) Not available with Low Power Output Code M.

(5) Thermowell Material is the same as the body material.

(6) Does not apply to Process Connection codes T1 and S1.

(7) Option P1 may not be ordered in combination with P2 or PA.

(11) Not available with Output Protocol code F.

(14) Only valid with FOUNDATION fieldbus Output Code F.

(16) Not available with FOUNDATION fieldbus (Output Code F).

Table 4. Flow Performance - Flow Reference Accuracy(1)

(2) For smaller line sizes, see Rosemount Compact Orifice

Rosemount 2051CF functional Turn-On Time

1000 cascade and feedforward.

 850 °F (454 °C) – Stainless Steel Sensor Material

Process Temperature Limits Failure Mode Alarm

Vibration Effect for 2051CFA, 2051CFC, and amplitude).(1)

Rosemount 2051CF physical Body

specifications  316 SST (CF8M), material per ASTM A351

Rosemount 2051CF product certifications