Chapter 3- Introduction to Dynamic

Routing Protocols
Exploration 2
KC Khor

1 KC KHOR Multimedia University

 Perspective & Background

Ways of
Classifying
IPv4 routing
Protocols (
Later)

2 KC KHOR Multimedia University

Dynamic Routing Protocols

Routing protocols allow routers to dynamically share
information about remote networks and automatically add this
information to their own routing tables.

Routing protocols determine the best path to each network
which is then added to the routing table.

Routing protocols are useful when there is a change in
network topology or when a particular path is failed.

Less administrative overhead compared to Static routes

But it requires resources of a router for protocol
operations including CPU time and network link bandwidth

*** Administrators use both static routes and routing
protocols for their networks. But it depends on situation.

3 KC KHOR Multimedia University

Compare Static Routes & Routing Protocols

4 KC KHOR Multimedia University

 Classifying Dynamic Routing Protocols
To understand Interior /
Exterior Gateway Routing protocol
, you need to understand AS

5 KC KHOR Multimedia University

Autonomous System (AS)

To understand Interior / Exterior Gateway Routing
protocol, you need to understand AS.

An autonomous system (AS) - otherwise known as a
routing domain - is a collection of routers under a
common administration.

Interior Gateway Protocols (IGP) are used routing inside
an autonomous system

Exterior Gateway Protocols (EGP) are used for routing
between autonomous systems.

6 KC KHOR Multimedia University

Autonomous System (AS) An AS comprised of many
individual networks
that are normally under an
ISP

7 KC KHOR Multimedia University

Classifying IGP

Interior Gateway Protocols (IGPs) can be classified as two
types:
- Distance vector routing protocols
- Link-state routing protocols

Distance vector means that routes are advertised as vectors of
distance and direction
- Ex: RIP, IGRP
- periodic updates are sent
- Ex of metric: hop count
- Best path: uses Bellman-Ford algorithm
- Information is exchanged via neighbors (thus don’t have
complete view of a network)

8 KC KHOR Multimedia University

Classifying IGP (Distance Vector)

When to use Distance Vector routing protocols?
- The network is simple and flat and does not require a
special hierarchical design.
- The administrators do not have enough knowledge to
configure and troubleshoot link-state protocols.
- Specific types of networks, such as hub-and-spoke
networks, are being implemented.
- Worst-case convergence times in a network are not a
concern.

9 KC KHOR Multimedia University

Classifying IGP (Link State)

Link State routing protocols are able to create a
complete view on a network by gathering information
from all the other routers.

All routers share the same topology map.

Best path to all the destinations is selected based on
the created topology map.

Link-state routing protocols do not use periodic updates.
After the network has converged, a link-state update only
sent when there is a change in the topology.

10 KC KHOR Multimedia University

Classifying IGP (Link State)

Link-state protocols work best in situations where:
- The network design is hierarchical, usually occurring in
large networks.
- The administrators have a good knowledge of the
implemented link-state routing protocol.
- Fast convergence of the network is crucial.

11 KC KHOR Multimedia University

Classful Routing Protocols

Network addresses were allocated based on classes, class
A, B, or C

In this case, the classful routing protocols did not need to
include the subnet mask in the routing update because
the network mask could be determined based on the first
octet of the network address

Therefore, classful routing protocols:
- cannot be used when a network is subnetted using
more than one subnet mask (VLSM)
- are unable to support discontiguous networks

Ex: RIPv1, IGRP
12 KC KHOR Multimedia University
Classless Routing Protocols

Today's networks are no longer allocated based on
classes and the subnet mask cannot be determined by the
value of the first octet.

Classless routing protocols include the subnet mask with
the network address in routing updates.

Therefore, they are able to support VLSM and
discontiguos networks

Ex: RIPv2, EIGRP, OSPF, IS-IS, BGP

13 KC KHOR Multimedia University

Classful vs Classless

14 KC KHOR Multimedia University

Convergence

Convergence is when all routers' routing tables are at a
state of consistency.

The network has converged when all routers have
complete and accurate information about the network.

Convergence properties include the speed of propagation
of routing information and the calculation of optimal
paths.

Routing protocols can be rated based on the speed to
convergence; the faster the convergence, the better the
routing protocol.

Generally, RIP and IGRP are slow to converge, whereas
EIGRP and OSPF are faster to converge

15 KC KHOR Multimedia University

Metrics

A metric is a value used by routing protocols to assign costs
to reach remote networks.

The metric is used to determine which path is most
preferable when there are multiple paths to the same
remote network.
RIP - hop count
IGRP and EIGRP:- Bandwidth, Delay, Reliability, and Load - Best
path is chosen by the route with the smallest composite
metric value calculated from these multiple parameters. By
default, only bandwidth and delay are used.
IS-IS and OSPF- Cost - Best path is chosen by the route with
the lowest cost. Cisco's implementation of OSPF uses
bandwidth.

16 KC KHOR Multimedia University

Metrics

Metrics used in IP routing protocols include:
Hop count - A simple metric that counts the number of
routers a packet must traverse
Bandwidth - Influences path selection by preferring the path
with the highest bandwidth
Load - Considers the traffic utilization of a certain link
Delay - Considers the time a packet takes to traverse a path
Reliability - Assesses the probability of a link failure, calculated
from the interface error count or previous link failures
Cost - A value determined either by the IOS or by the
network administrator to indicate preference for a route. Cost
can represent a metric, a combination of metrics or a policy.
17 KC KHOR Multimedia University
RIP and its Metric

RIP 2 hop counts from R2 to 192.168.8.0

18 KC KHOR Multimedia University

Administrative Distance (AD)

How does a router determine which route to install in the routing table when
it has learned about the same network from more than one routing source?

In this case, you need AD.

Administrative distance (AD) defines the preference of a routing source.

Which route will R2 choose to send packets to the destination network
192.168.6.0?

19 KC KHOR Multimedia Univ. , Cyberjaya

Administrative Distance (AD)

AD / Metric Value

20 KC KHOR Multimedia University

AD (Directly Connected Networks & Static
Routes)

AD for directly connected networks – 0

The AD value is not listed in show ip route for directly
connected networks

AD for static routes (next hop IP or exit interface) – 1

The AD value is not listed in show ip route when you
configure a static route with the exit interface specified

21 KC KHOR Multimedia University

 The End

http://fit.mmu.edu.my/cisco

22 KC KHOR Multimedia University