TitanServiceManual PDF

Ultrasound System
Service Manual
Manufactured by
SonoSite, Inc.
21919 30th Drive SE
Bothell, WA 98021-3904
USA
Telephone: 1-888-482-9449 or 1-425-951-1200
Fax: 1-425-951-1201
SonoSite Ltd
Alexander House
40A Wilbury Way
Hitchin, Herts
SG4 OAP UK
T: +44-1462-444800
F: +44-1462-444801
Caution: United States federal law restricts this device to sale by or on the order of a physician.
“TITAN” and “SonoSite TITAN” are trademarks of SonoSite, Inc.
Kensington is a registered trademark of Kensington Technology Group.
Non-SonoSite product names may be trademarks or registered trademarks of their respective owners.
SonoSite products may be covered by one or more of the following U.S. patents: 4454884, 4462408, 4469106, 4474184, 4475376, 4515017, 4534357,
4542653, 4543960, 4552607, 4561807, 4566035, 4567895, 4581636, 4591355, 4603702, (4607642), 4644795, 4670339, 4773140, 4817618, 4883059,
4887306, 5016641, 5050610, 5095910, 5099847, 5123415, 5158088, 5197477, 5207225, 5215094, 5226420, 5226422, 5233994, 5255682, (5275167),
5287753, 5305756, 5353354, 5365929, 5381795, 5386830, 5390674, 5402793, (5,423,220), 5438994, 5450851, 5456257, 5471989, 5471990, 5474073,
5476097, 5479930, 5482045, 5482047, 5485842, 5492134, 5517994, 5529070, 5546946, 5555887, 5603323, 5606972, 5617863, (5634465), 5634466,
5636631, 5645066, 5648942, 5669385, (5706819), 5715823, 5718229, 5720291, 5722412, 5752517, 5762067, 5782769, 5800356, 5817024, 5833613,
5846200, 5860924, 5893363, 5916168, 5951478, 6036643, 6102863, 6104126, 6113547, 6117085, 6142946, 6203498 B1, 6371918, 6135961, D0280762,
D0285484, D0286325, D0300241, D0306343, D0328095, D0369307, D0379231. Other patents pending.
P03309-02 01/2004
Copyright 2004 by SonoSite, Inc.
All rights reserved. Printed in the USA.
ii
Contents
Chapter 1: Introduction
1.1 Audience ..............................................................................................1
1.2 Conventions Used in This Service Manual ....................................1
1.3 Product Upgrades and Updates ......................................................1
1.4 Customer Comments .........................................................................1
1.5 About the System ...............................................................................2
1.6 About the System Software ..............................................................4
1.7 Software Licensing .............................................................................4
Chapter 2: Safety
2.1 Electrical Safety ..................................................................................5
2.2 Equipment Safety ...............................................................................6
2.3 Battery Safety ......................................................................................6
2.4 Biological Safety .................................................................................7
2.5 Labeling Symbols ...............................................................................7
Chapter 3: System Overview

3.1 System Overview ...............................................................................9
3.2 Theory of Operation ..........................................................................9
3.2.1 Transducer ..............................................................................10
3.2.2 Front End Subsystem ............................................................10
3.2.3 Digital Signal Processing Subsystem ..................................12
3.2.4 Backend Subsystem ...............................................................12
3.2.5 Control Subsystem ................................................................14
3.2.6 Power Supply and Control Subsystem ..............................15
3.3 System Specifications ......................................................................16
3.3.1 System Dimensions ...............................................................16
3.3.2 Display Dimensions ..............................................................16
3.3.3 Transducers ............................................................................16
3.3.4 Imaging Modes ......................................................................16
3.3.5 Applications ...........................................................................16
3.3.6 Image Storage .........................................................................17
3.3.7 Accessories .............................................................................17
3.3.8 Peripherals ..............................................................................17
3.3.9 Temperature, Pressure, and Humidity Limits ..................18
3.3.10 Electrical ................................................................................18
3.3.11 Electromechanical Safety Standards .................................18
3.3.12 EMC Standards Classification ...........................................18
3.3.13 Airborne Equipment Standards ........................................19
3.3.14 ECG Standard ......................................................................19
3.3.15 DICOM Standard .................................................................19
Chapter 4: Setup and Operation

4.1 System Controls ................................................................................21
4.2 System Components ........................................................................22
4.3 Setup ..................................................................................................23
4.4 Touchpad ...........................................................................................24
4.5 Accessories ........................................................................................24
4.6 Preparing the System for Operation ..............................................25
4.6.1 Installing and Removing the Battery ..................................25
4.6.2 Using AC Power/Charging Battery ...................................26
4.6.3 Connecting to AC Power ......................................................27
4.6.4 Connecting and Removing Transducers ............................28
4.6.5 Turning the System On and Off ..........................................28
iii
4.7 Upgrading the System Software ....................................................29
4.7.1 Obtaining a License Key .......................................................34
4.7.2 Installing a License Key ........................................................34
4.7.3 To Display the System Information Screen .......................35
4.7.4 To Display the License Update Screen ...............................35
Chapter 5: Cleaning and Disinfecting

5.1 Universal Precautions ......................................................................37
5.2 Receipt of Suspected Contaminated Materials ............................37
5.3 Recommended Disinfectants ..........................................................37
Chapter 6: Troubleshooting
6.1 Basic Troubleshooting .....................................................................39
6.2 Periodic Maintenance ......................................................................40
6.3 System and Subsystem Diagnosis .................................................40
6.4 System Repair ...................................................................................41
6.5 Test Equipment ................................................................................41
6.6 Failure Modes ...................................................................................41
6.6.1 Display ....................................................................................41
6.6.2 Control Panel ..........................................................................41
6.6.3 System/Main PCBA ..............................................................41
6.6.4 Battery .....................................................................................42
6.6.5 Mini-Dock/Mobile Docking System ..................................42
6.6.6 DICOM ....................................................................................42
6.7 Troubleshooting Flow Diagrams ...................................................43
6.7.1 Display ....................................................................................43
6.7.2 Control Panel ..........................................................................44
6.7.3 System .....................................................................................45
6.7.4 Battery .....................................................................................46
6.7.5 Mini-Dock/Mobile Docking System ..................................47
6.7.6 Triple Transducer Connect ..................................................49
Chapter 7: Replacement Procedures

7.1 Display Replacement .......................................................................51
7.1.1 Required Parts ........................................................................51
7.1.2 Required Tools .......................................................................51
7.1.3 Display Removal ....................................................................51
7.1.4 Display Replacement ............................................................53
7.1.5 Test the Display .....................................................................54
7.2 Control Panel Subassembly Replacement ....................................54
7.2.1 Required Parts ........................................................................54
7.2.2 Required Tools .......................................................................54
7.2.3 Control Panel Removal .........................................................54
7.2.4 Control Panel Replacement ..................................................54
7.3 Main System Disassembly for Repair and/or Replacement .....55
7.3.1 Required Parts ........................................................................55
7.3.2 Required Tools .......................................................................55
7.3.3 Main PCBA Removal ............................................................55
Chapter 8: Performance Testing

8.1 Overview ...........................................................................................61
8.2 Test Equipment ................................................................................61
8.3 Setting Up Performance Tests ........................................................61
8.3.1 Scan Reference Orientation ..................................................61
iv
8.4 Testing 2D Performance ..................................................................62
8.4.1 2D Image Quality ..................................................................62
8.4.2 Axial Measurement Accuracy .............................................62
8.4.3 Lateral Measurement Accuracy ...........................................63
8.4.4 Penetration ..............................................................................63
8.5 Additional Performance Tests ........................................................64
8.5.1 CPD ..........................................................................................64
8.5.2 Directional Color Power Doppler (DCPD) ........................64
8.5.3 M Mode Imaging ...................................................................65
8.5.4 Tissue Harmonic Imaging ....................................................65
8.5.5 Pulsed Wave (PW) Doppler Imaging .................................65
8.5.6 Image Quality Verification Test/Livescan ........................65
8.5.7 Image Review .........................................................................65
8.5.8 Printer ......................................................................................66
8.5.9 Battery Charging ....................................................................66
8.5.10 Video Output .......................................................................66
8.6 Returning Products to SonoSite .....................................................67
8.6.1 Contacting SonoSite Technical Support .............................67
8.6.2 Shipping Instructions ............................................................67
Chapter 9: Accessory Service

9.1 Mobile Docking System ..................................................................69
9.2 Mini-Dock ..........................................................................................71
9.3 Connectivity ......................................................................................71
9.3.1 Connection Panel ...................................................................71
9.3.2 Docking System/Mini-Dock Connections .........................72
9.4 Block Diagrams and Schematics ....................................................72
9.5 Theory of Operation ........................................................................80
9.5.1 Video .......................................................................................80
9.5.2 Power Distribution ................................................................80
9.6 Replacement Procedures .................................................................81
9.6.1 Required Tools .......................................................................81
9.6.2 Cup Surround ........................................................................81
9.6.3 Casters .....................................................................................81
9.6.4 Power Supply .........................................................................82
9.6.5 Locking Handle .....................................................................84
9.6.6 Deflector ..................................................................................84
9.6.7 Mini-Dock ...............................................................................84
9.6.8 Triple Transducer Connect ..................................................86
Appendix A: Parts List

A.1 Replacement Parts List ...................................................................89
A.1.1 Display ...................................................................................89
A.1.2 Control Panel ........................................................................90
A.1.3 Replacement Parts, System .................................................91
A.1.4 Transducer Nest Frame Assembly .....................................96
A.1.5 AC Adapter ...........................................................................97
A.1.6 Mini-Dock ..............................................................................98
A.1.7 Mobile Docking System .......................................................99
A.1.8 Triple Transducer Connect ...............................................102
A.2 Ordering Replacement Parts .......................................................103
Appendix B: Service Event Report
Index .................................................................................................107
v
vi
Chapter 1: Introduction
Before servicing the TITANTM high-resolution ultrasound system, please read the information in this manual. This
text applies only to the SonoSite TITAN ultrasound system product manufactured after June 19, 2003. Please find
service information about products manufactured before June 17, 2003 in C1.51 Ultrasound System Service Manual
(P00715), C1.75 Ultrasound System Service Manual (P01118), C1.9 PLUS Ultrasound System Service Manual (P02287),
and C1.99 PLUS and ELITE Ultrasound System Service Manual (P02913).
1.1 Audience
The intended audience of this manual is properly trained field and in-house service personnel.
1.2 Conventions Used in This Service Manual

These conventions are used in this service manual:
• A Warning describes precautions necessary to prevent injury or loss of life.
• A Caution describes precautions necessary to protect the products.
• When the steps in the operating instructions must be performed in a specific order, the steps are numbered.
• Bulleted lists present information in list format, but they do not imply a sequence.
• The system handle is on the front of the system, and the battery compartment is on the back of the system.
1.3 Product Upgrades and Updates

SonoSite may offer software upgrades and new features that may improve system performance. Service manual
updates, explaining the effects of upgrades and new features on system performance, will accompany the
upgrades.
1.4 Customer Comments

Questions and comments are encouraged. SonoSite is interested in your feedback regarding the service manual.
Please call SonoSite at 1-877-657-8118. If you are outside the USA, call the nearest SonoSite representative. You
can also send electronic mail (e-mail) to SonoSite at the following address:
[email protected]
Chapter 1: Introduction 1
1.5 About the System
The ultrasound system has multiple configurations and feature sets. All are described in this service manual but
not every option may apply to your system. System features are dependent on your system configuration,
transducer, and exam type.
Figure 1.1 TITAN System Front View
Table 1.1: TITAN System Front Features
Number Feature
1 Control panel
2 Transducer connection
3 Handle
4 Display
5 CompactFlash™ slots (front for image storage, back for system and transducers updates and
import/export of DICOM configuration)
2 Chapter 1: Introduction
1
2 3 4
Figure 1.2 TITAN System Rear View
Table 1.2: TITAN System Rear Connectors
Number Feature
1 DC input connector
2 I/O connector
3 Battery
4 ECG connector (available on future releases)
The TITAN system is a portable, software-controlled, ultrasound system using all-digital architecture. The
system is used to acquire and display high-resolution, real-time ultrasound images: 2D, color power Doppler
(CPD), directional color power Doppler (DCPD), Tissue Harmonic Imaging (THI), M Mode, and pulsed wave
(PW) Doppler. The system has cine buffer, image zoom, labeling, biopsy, measurements, calculations, a USB
connection for image transfer, image storage, image review, printing, recording, and the ability to archive
Doppler with audio output to a videotape.
Currently, the system supports the following broadband transducers:
• C8/8-5 MHz 8 mm microcurved array
• C60/5-2 MHz 60 mm curved array
• HST/10-5 MHz 25 mm linear array
• ICT/8-5 MHz 11 mm intracavitary array
• L38/10-5 MHz 38 mm linear array
System accessories include the TITAN mobile docking system, the TITAN mini-dock, a power supply, a battery,
video and printer cables, and SiteLink Image Manager 2.1 software.
System peripherals include medical grade (conforming to the requirements of EN60601-1) and non-medical
(commercial) grade products. System medical grade peripherals include a printer and VCR. System non-medical
grade peripherals include a CompactFlash card and a Kensington Security Cable. Use of peripherals is covered
in the manufacturers’ instructions, which accompany each peripheral.
Chapter 1: Introduction 3
1.6 About the System Software
The ultrasound system contains software that controls its operation. A software upgrade may be required.
SonoSite will provide you with a CompactFlash card containing the software. Typically new software provides
new capabilities. A single CompactFlash card can be used to update one or more systems. Software upgrades use
the back CompactFlash slot on the right hand side of the system. CompactFlash cards installed in the front
CompactFlash slot do not upgrade the system.
1.7 Software Licensing

SonoSite software is controlled by a license key, which is obtained from SonoSite or from its authorized
representatives. You must obtain one key for each system or transducer that will use the new software. See
“Obtaining a License Key” on page 34.
The software may be installed and will operate for a short period of time without requiring a valid license key.
We refer to this period of time as the “grace period.” The grace period is variable.
When you first install your software, your SonoSite system prompts you for a license key. If you have not yet
obtained a valid license key, you can elect to use the software as long as the grace period time has not been fully
consumed.
When a system is running in the grace period, all system functions are available. As you use the system, the grace
period is slowly consumed. When the grace period has expired, the system will not be usable until a valid license
key has been entered. Grace period time is not consumed while the system is powered off or when it is in “sleep”
mode. Whenever a system is running in the grace period, the grace period time remaining is available on the
license update screen.
Caution: When the grace period expires, all system functions except for licensing are unavailable until a
valid license key is entered into the system.
4 Chapter 1: Introduction
Chapter 2: Safety
Read this information before using the ultrasound system. The information in this manual applies to the
ultrasound system, transducer, accessories, and peripherals. This chapter contains safety information.
A Warning describes precautions necessary to prevent injury or loss of life.
A Caution describes precautions necessary to protect the products.
2.1 Electrical Safety

This system meets EN60601-1, Class I/internally-powered equipment requirements and Type BF isolated
patient-applied parts safety requirements.
This system complies with the applicable medical equipment requirements published in the Canadian Standards
Association (CSA), European Norm Harmonized Standards, and Underwriters Laboratories (UL) safety
standards.
For maximum safety observe the following warnings and cautions:
Warning: To avoid the risk of electrical shock or injury, do not open the system enclosures. All internal
adjustments and replacements, except battery replacement, must be made by a qualified
technician.
To avoid the risk of injury, do not operate the system in the presence of flammable gasses or
anesthetics. Explosion can result.
To avoid the risk of electrical shock, use only properly grounded equipment. Shock hazards
exist if the power supply is not properly grounded. Grounding reliability can only be achieved
when equipment is connected to a receptacle marked “Hospital Only” or “Hospital Grade” or
the equivalent. The grounding wire must not be removed or defeated.
To avoid the risk of electrical shock, before using the transducer, inspect the transducer face,
housing, and cable. Do not use the transducer if the transducer or cable is damaged.
To avoid the risk of electrical shock, always disconnect the power supply from the system before
cleaning the system.
To avoid the risk of electrical shock, do not use any transducer that has been immersed beyond
the specified cleaning or disinfection level. See Chapter 5, “Cleaning and Disinfecting.”
To avoid the risk of electrical shock and fire hazard, inspect the power supply, AC power cord
and plug on a regular basis. Ensure they are not damaged.
To avoid the risk of electrical shock, use only accessories and peripherals recommended by
SonoSite, including the power supply. Connection of accessories and peripherals not
recommended by SonoSite could result in electrical shock. Contact SonoSite or your local
representative for a list of accessories and peripherals available from or recommended by
SonoSite.
To avoid the risk of electrical shock, use commercial grade peripherals recommended by
SonoSite on battery power only. Do not connect these products to AC mains power when using
the system to scan or diagnose a patient/subject. Contact SonoSite or your local representative
for a list of the commercial grade peripherals available from or recommended by SonoSite.
To avoid the risk of electrical shock, inspect the interconnect cables on a regular basis for
damage.
To avoid the risk of electrical shock to the patient/subject, do not touch the system battery
contacts while simultaneously touching a patient/subject.
To prevent injury to the operator/bystander, the transducer must be removed from patient
contact before the application of a high-voltage defibrillation pulse.
Chapter 2: Safety 5
Caution: Although your system has been manufactured in compliance with existing EMC/EMI
requirements (EN60601-1-2), use of the system in the presence of an electromagnetic field can
cause degradation of the ultrasound image. If this occurs often, SonoSite suggests a review of
the system environment. Identify and remove the possible sources of the emissions or move
your system.
Electrostatic discharge (ESD), or static shock, is a naturally occurring phenomenon. ESD is
common in conditions of low humidity, which can be caused by heating or air conditioning.
Static shock is a discharge of the electrical energy from a charged body to a lesser or
non-charged body. The degree of discharge can be significant enough to cause damage to a
transducer or an ultrasound system. The following precautions can help reduce ESD: anti-static
spray on carpets, anti-static spray on linoleum, and anti-static mats.
Do not use the system if an error message appears on the display: note the error code; call
SonoSite or your local representative; turn off the system by pressing and holding the power key
until the system powers down.
To avoid increasing the system and transducer connector temperature, do not block the airflow
to the ventilation holes on the side of the system.
2.2 Equipment Safety

To protect your ultrasound system, transducer, and accessories, follow these precautions.
Caution: Excessive bending or twisting of cables can cause a failure or intermittent operation.
To avoid damaging the power supply, verify the power supply input is within the correct
voltage range. See “Electrical” on page 18 in Chapter 3.
Improper cleaning or disinfecting of any part of the system can cause permanent damage. For
cleaning and disinfecting instructions, see Chapter 5, “Cleaning and Disinfecting.”
Do not use solvents such as thinner or benzene, or abrasive cleaners on any part of the system.
Remove the battery from the system if the system is not likely to be used for some time.
Do not spill liquid on the system.
2.3 Battery Safety

To prevent the battery from bursting, igniting, or emitting fumes and causing equipment damage, observe the
following precautions.
Warning: The battery has a safety device. Do not disassemble or alter the battery.
Charge the batteries only when the ambient temperature is between 0° and 45°C (32° and 113°F).
Do not short-circuit the battery by directly connecting the positive and negative terminals with
metal objects.
Do not heat the battery or discard it in a fire.
Do not expose the battery to storage temperatures over 60°C (140°F). Keep it away from fire and
other heat sources.
Do not charge the battery near a heat source, such as a fire or heater.
Do not leave the battery in direct sunlight.
Do not pierce the battery with a sharp object, hit it, or step on it.
Do not use a damaged battery.
Do not solder a battery.
6 Chapter 2: Safety
Warning: The polarity of the battery terminals is fixed and cannot be switched or reversed. Do not force
the battery into the system.
Do not connect the battery to an electrical power outlet.
Do not continue recharging the battery if it does not recharge after two successive six hour
charging cycles.
Caution: To prevent the battery from bursting, igniting, or emitting fumes and causing equipment
damage, observe the following precautions.
Do not immerse the battery in water or allow it to get wet.
Do not put the battery into a microwave oven or pressurized container.
If the battery leaks or emits an odor, remove it from all possible flammable sources.
If the battery emits an odor or heat, is deformed or discolored, or in any way appears abnormal
during use, recharging or storage, immediately remove it and stop using it. If you have any
questions about the battery, consult SonoSite or your local representative.
Store the battery between -20°C (-4°F) and 60°C (140°F).
Use only SonoSite batteries.
Do not use or charge the battery with non-SonoSite equipment. Only charge the battery with the
TITAN system.
2.4 Biological Safety

Observe the following precautions related to biological safety.
Warning: Non-medical (commercial) grade peripheral monitors have not been verified or validated by
SonoSite as being suitable for diagnosis.
Do not use the system if it exhibits erratic or inconsistent behavior. Discontinuities in the
scanning sequence are indicative of a hardware failure that must be corrected before use.
Do not use the system if it exhibits artifacts on the LCD screen, either within the clinical image or
in the area outside of the clinical image. Artifacts are indicative of hardware and/or software
errors that must be corrected before use.
Some transducer sheaths contain natural rubber latex and talc, which can cause allergic
reactions in some individuals. Refer to 21 CFR 801.437, User labeling for devices that contain
natural rubber.
Perform ultrasound procedures prudently. Use the ALARA (as low as reasonably achievable)
principle.
SonoSite does not currently recommend a specific brand of acoustic standoff.
2.5 Labeling Symbols

Labeling symbols for SonoSite products can be found in the user guide for each product.
Chapter 2: Safety 7
8 Chapter 2: Safety
Chapter 3: System Overview
3.1 System Overview

The system houses the system electronics, display, control panel, and the system batteries. It provides basic
connections for external power, and the transducer connector and a general purpose docking connector for all
other interfaces. The system operates with external transducers and optional peripheral equipment. The types of
external devices that may be used are:
• Transducer(s)
• AC Power Supply/Charger
• Mobile Docking System/Mini-dock
• External Peripherals
The transducer connects to the main unit through the scanhead connector. The transducer contains data, which
the system uses to drive the transducer in the scanhead, process the data received back and format and display
the data for the user. The interface is backward compatible to previous systems and scanheads.
The AC power supply not only provides power from the AC mains for operating the system, it also contains the
charger for charging the internal system battery. This may be used if a mobile docking system or mini-dock is not
desired or available.
The mobile docking system provides power to run the system, contains the charger to charge the internal system
battery and provides fixed external power, video, RS-232, and USB connections. The docking system may also
provide additional control surfaces and monitors. The unit interfaces to the docking system through connections
on the back of the unit. It provides a convenient place for the unit to be operated and stored under certain usage
scenarios.
The mini-dock provides the breakout for all the connectors from the docking connector for remote use where a
docking system may not be available and the external connections are desired. The use of a mini-dock allows the
main unit to be more portable when the connections are not required.
External OEM peripherals are items such as monitor, printers, and VCRs. These can be connected to the mobile
system or directly to the system with the use of the mini-dock using the video and/or printer control
input/outputs.
3.2 Theory of Operation

The system has six major functional groups: the transducer, the frontend subsystem, the digital signal processing
subsystem, the backend subsystem, the control subsystem, and the power supply and control subsystem.
Figure 3.1 shows how these functions interact.
Chapter 3: System Overview 9

Figure 3.1 TITAN Block Diagram
3.2.1 Transducer
The transducer elements convert the pulser voltage to acoustic energy during the “transmit” portion of the
ultrasound acquisition cycle. Also, the transducer elements convert the acoustic echo to voltage in the “receive”
portion of the acquisition cycle. The system transducers have 64 to 128 elements. The front end subsystem senses
the voltage developed on the transducer elements.
3.2.2 Front End Subsystem

The Front End is designed to support various imaging modalities such as 2D, spectral Doppler and color
Doppler. From the Front End's perspective all modes can be grouped into a few basic types: single mode,
simultaneous modes and triggered modes. All these modes are built from similar, basic transmit and receive
sequences controlled within the Front End. A generic top level block diagram of a typical Front End is in the
following figure.
10 Chapter 3: System Overview

Figure 3.2 Front End Subsystem
The transmit section consists of a waveform generator, delay block, and high power high voltage driver to excite
the transducer element. Multiple elements are driven with delays determined by the time of flight in the medium
from the elements to the point in space where the beam is to be focused. The longer the time of flight is to the
focal point the smaller the delay is for a given transmit element to allow all to arrive at the focal point at the same
time. The number of elements driven is determined by element sensitivity off axis and depth of field
considerations. The waveform is selected to drive the transducer at a certain center frequency, bandwidth, and
power and is optimized for the given mode.
The receive section consists of a transmit/receive switch to protect the receiver from the transmit voltage, a
variable gain receiver to amplify and condition the return echoes, an A/D to digitize the data, a delay block to
focus the return signals and a weight block to scale the return echoes for each channel. All the signals are then
summed together to generate the beamformed receive data. The analog gain varies with depth to compensate for
signal attenuation through the medium. The delays and weights are independent for each channel. The delay and
weight for the receive channel can typically be changed dynamically to keep the receive beam in continuous
focus. The delay is simply set by the time of flight in the medium from the point of interest to the element, which
starts at skinline and proceeds to the deepest depth of interest.
The control section drives the data to the various data path elements on a line by line basis, controls the timing
for the transmit and receive sections, and controls the tagged information and timing of the data to the rest of the
system.
Unique transmit and receive sequences, lines or PRIs, are arranged into repeated groups or frames. The simplest
frame is for a single mode where the line does not change, for example M Mode or PW Doppler. Here the same
line characteristics; aperture size, delay, weights, and waveform information, are continually repeated. A
scanned single mode, such as 2D, keeps the same transmit aperture size but the delays and receive weights
change due to the aperture translation or steering changes with each line acquired. Simultaneous modes may also
change the transmit waveform and aperture size and the delays and receive weights. Downstream processing
also changes, due to the unique processing requirements for the different types of data. Triggered modes are the
same as the previous modes except that the frames are started and stopped on user or external inputs.

3.2.3 Digital Signal Processing Subsystem
The DSP subsystem receives data from the front end chip sets, performs processing to enhance the signal-to-noise
ratio of signal features of interest, and prepares data for raster scan conversion and display.
Figure 3.3 Digital Signal Processing Subsystem
3.2.4 Backend Subsystem

The Backend subsystem is responsible for the conversion of raw acquisition data into a raster image ready for
display. This includes the acquisition data path with flash suppression and temporal filtering, and the display
data path with scan conversion into raster space. The Backend subsystem also contains the video data path that
supports generation of video comprising of the ultrasound image as well as graphics annotation. Video
generation of both standard composite interlaced video and progressive scan video is supported. Most
functionality is within the ASIC. However, the memory resources for acquisition memory, and display memory
are found in external memory components. The conversion from PC type video to TV type video is also
performed externally.
Control is received initially from the CPU to setup each functional block and afterward the hardware is
completely data driven. This control takes the form of programming setup registers inside the blocks and setting
up scan conversion tables. Each block provides temporary storage as required to buffer data and keep their
respective processing pipeline full and operating. Also note that the block diagrams show only the data path, but
each block is responsible for generating any necessary memory addresses for their respective input data stream.

The BackEnd subsystem is shown in the figure below.
Figure 3.4 BackEnd Subsystem Block Diagram
The backend subsystem performs processing encompassing three main data domains, acquisition data, raster
data, and video data.
Support for acquisition data includes the input buffer, flash suppression, frame average, and external ACQ
memory. Cine buffer management is performed by the acquisition controller.
Conversion from acquisition data to raster data is performed by the graphics overlay, scan conversion engine,
sweeping engine, and 3D engine. Raster data is stored in an external DISPLAY memory. Also supporting raster
operations is the graphics support block that provides acceleration hardware for pixel operations from the CPU
and graphics overlay engine.
Video data is processed as progressive scan (60 Hz) and supplied externally on a digital bus. In addition,
interlaced (30 Hz) video is supplied in both composite and S-video formats. The progressive video path includes
buffers, priority logic, and LUTs. External video in signals are input and multiplexed onto the external video out
path to allow for external sources to display information on connected displays, VCRs, or printers.

3.2.5 Control Subsystem
The control subsystem is shown in the figure below.
Figure 3.5 Control Subsystem
The core control subsystem contains the processor, the system bus, the system memory resources of FLASH and
RAM, the interrupt logic, system timers, a DMA engine, and a floating point unit.
Support for the ultrasound subsystem consists of a scanhead interface, scanhead mux control, a portion of the
system FLASH for storage of saved images, and a control path to program the ultrasound datapath.
Communication interfaces consist of an Ethernet interface, USB port, two general purpose serial bus interfaces,
and the I2C bus.

3.2.6 Power Supply and Control Subsystem
The system Power Supply and Control System consists of an easily replaced rechargeable battery pack; an
On/Off Key; a standby power regulator; digital, analog, display and transducer power supplies; a power monitor
and a power control system. Operating current is drawn from the battery or an external AC/DC Adapter, which
also contains circuitry for charging the battery.
The Power Supply and Control Subsystem are in the figure below.
VEXT Standby Power VSTBY

Regulator
Power VEXTS
Select On/Off
VBAT VBATS On/Off Key
Latch
Power PWR_Enable
Switch
VPWR
VCC(n)
Digital VCC1
Off
Power VCC1_Good RSTN
Supplies
DPS_Enables
CPU
PS_Bus
VEXTS
Battery BDATA
Pack
+HVB
+HV
+6V
Analog
-6V
Power
Supplies HV_ADJ Power
APS_Enable Monitor
APS_Sense and
Control
Fan Fan_Enable Temp
Sense
BL_PWR
Display LCD(n)
Power LCD_Control
Supplies LCD_Enable
SH_5V
Transducer
SH_3.3V
Power
SH_VPP
Supplies SH_Enable
Figure 3.6 Power Supply and Control System Block Diagram

3.3 System Specifications
This section contains system and accessory specifications and agency approvals. The specifications for
recommended peripherals can be found in the manufacturers’ instructions.
3.3.1 System Dimensions

Length: 11.8 in. (29.97 cm)
Width: 10.9 in. (27.69 cm)
Depth: 3.0 in. (7.62 cm)
Weight: 8.3 lbs. (3.76 kg) with the C60 transducer and battery installed
3.3.2 Display Dimensions

Length: 5.1875 in. (13.18 cm)
Width: 6.75 in. (17.15 cm)
Diagonal: 8.5 in. (21.59 cm)
3.3.3 Transducers
• C8/8-5 MHz 8 mm curved array (5 ft./1.5 m)
• C11/8-5 MHz 11 mm microcurved array (5 ft./1.5 m)
• C15/4-2 MHz 15 mm microcurved array (5.5 ft./1.7 m)
• C60/5-2 MHz 60 mm curved array (5 ft./1.5 m)
• HST/10-5 MHz 25 mm linear array (8 ft./2.1 m)
• ICT/8-5 MHz 11 mm intracavitary array (5 ft./1.5 m)
• L38/10-5 MHz 38 mm linear array (5.5 ft./1.7 m)
3.3.4 Imaging Modes

2D (256 gray shades)
Color power Doppler (CPD) (256 colors)
Directional color power Doppler (DCPD) (256 colors)
M Mode
Pulsed wave (PW) Doppler
Tissue Harmonic Imaging
3.3.5 Applications
Abdominal Imaging
Cardiac Imaging
Gynecology and Fertility Imaging
Interventional and Intraoperative Imaging Applications
Obstetrical Imaging
Pediatric and Neonatal Imaging
Prostate Imaging
Superficial Imaging
Vascular Imaging

3.3.6 Image Storage
The number images saved to the CompactFlash card vary depending on the card storage capacity.
Cine buffer
3.3.7 Accessories
3.3.7.1 Hardware, Software, and Documentation
AIUM Ultrasound Medical Safety Guidance Document
Battery
Biopsy Guide
Carry case
External display
Mobile Docking System
Mini-Dock
Power supply
Quick Reference Guide
SiteLink Image Manager 2.1
System User Guide
Triple Transducer Connect
Ultrasound gel
3.3.7.2 Cables
Ethernet cable (10 ft./3 m)
Ethernet interface cable (7 in./18 cm)
External display power cord (6 ft./1.8 m)
External display VGA cable (3 ft./0.9 m)
Print control cable (10 ft./3.1 m)
Printer AC power cord (1 ft./30.5 cm)
VCR AC power cord (1.5 ft./45.7 cm)
VCR (control/audio) cable (6 ft./1.8 m)
Video cable (RCA/RCA) (10 ft./3.1 m)
Video cable (RCA/BNC) (10 ft./3.1 m)
S-video (6 ft./1.8 m)
System AC power cord (10 ft./3.1 m)
USB cable for SiteLink (10 ft./3.1 m)
3.3.8 Peripherals
See the manufacturer’s specifications for the following peripherals.
3.3.8.1 Medical Grade

Black-and-white printer
Recommended sources for printer paper: Contact Sony at 1-800-686-7669 or www.sony.com/professional
to order supplies or to obtain the name and number of the local distributor.
Color printer
Video cassette recorder
3.3.8.2 Non-Medical Grade

Kensington Security Cable

3.3.9 Temperature, Pressure, and Humidity Limits
The temperature, pressure, and humidity limits apply only to the ultrasound system and transducers.
Operating Limits: System
• 10–40°C (50–104°F), 15–95% R.H.
• 700 to 1060hPa (0.7 to 1.05 ATM)
Shipping/Storage Limits: System without Battery
• -35–65°C (-31–149°F), 15–95% R.H.
• 500 to 1060hPa (0.5 to 1.05 ATM)
Operating Limits: Battery
• 10–40°C (50–104°F), 15–95% R.H.
Shipping/Storage Limits: Battery
• -20–60°C (-4–140°F), 0–95% R.H.*
• 500 to 1060hPa (0.5 to 1.05 ATM)
* For storage longer than 30 days, store at or below room temperature.
Operating Limits: Transducer
• 10–40°C (50–104°F), 15–95% R.H.
Shipping/Storage Limits: Transducer
• -35–65°C (-31–149°F), 15–95% R.H.
3.3.10 Electrical
Power Supply Input: 100-240 VAC, 50/60 Hz, 1.2 A Max @ 100 VAC.
Power Supply Output (system on): (1) 15 VDC, 2.7A Max (system)
(2) 12.6 VDC, 0.8A Max (battery charging)
Power Supply Output (system off): (1) 15 VDC, 2.0A Max (system)
(2) 12.6 VDC, 1.8A Max (battery charging)
Combined output not exceeding 52W.
Battery
• 6-cell, 11.25 VDC, 4.4 amp-hours, rechargeable lithium ion battery pack.
• Run time is 2 hours or more, depending on imaging mode and display brightness.
3.3.11 Electromechanical Safety Standards

EN 60601-1:1997, European Norm, Medical Electrical Equipment–Part 1. General Requirements for Safety.
EN 60601-1-1:2001, European Norm, Medical Electrical Equipment–Part 1. General Requirements for
Safety–Section 1-1. Collateral Standard. Safety Requirements for Medical Electrical Systems.
C22.2, No. 601.1:1990, Canadian Standards Association, Medical Electrical Equipment–Part 1. General
Requirements for Safety.
CEI/IEC 61157:1992, International Electrotechnical Commission, Requirements for the Declaration of the
Acoustic Output of Medical Diagnostic Ultrasonic Equipment.
UL 2601-1:1997, Second Edition, Underwriters Laboratories, Medical Electrical Equipment-Part 1: General
Requirements for Safety.
3.3.12 EMC Standards Classification

EN 60601-1-2:2001, European Norm, Medical Electrical Equipment. General Requirements for Safety-Collateral
Standard. Electromagnetic Compatibility. Requirements and Tests.
CISPR11:97, International Electrotechnical Commission, International Special Committee on Radio Interference.
Industrial, Scientific, and Medical (ISM) Radio-Frequency Equipment Electromagnetic Disturbance
Characteristics-Limits and Methods of Measurement.
The Classification for the SonoSite system, SiteStand, accessories, and peripherals when configured together is:
Group 1, Class A.

3.3.13 Airborne Equipment Standards
RTCA/DO160D:1997, Radio Technical Commission for Aeronautics, Environmental Conditions and Test
Procedures for Airborne Equipment, Section 21.0 Emission of Radio Frequency Energy, Category B.
3.3.14 ECG Standard

ANSI/AAMI EC53-1995, Association for the Advancement of Medical Instrumentation, ECG Cables, and Lead
Wires.
The SonoSite ultrasound system meets the requirements of this standard except Section 4.4.1 (Exposure to
ethylene oxide (EO) sterilization) and Section 4.5.9 (Connector retention force). The requirement in Section 4.5.9
does not apply, because the product weighs less than 8. 4 pounds.
3.3.15 DICOM Standard

NEMA PS 3.15: 2000, Digital Imaging and Communications in Medicine (DICOM)-Part 15: Security Profiles.

Chapter 4: Setup and Operation
4.1 System Controls
1 14
2
15
3
4 16
5
17
18
6 19
20
8 9 10 11 12 13
Figure 4.1 System Controls
Table 4.1: System Controls
Number System Control Description
1 Power Turns system on and off.
2 Alphanumeric Use to enter text and numbers.
3 Annotation Text Turns the keyboard on and off for text entry.
Picto Turns the pictographs/pictograph marker on and off.
Arrow Displays an arrow that can be moved and rotated within the
image area.
4 THI Turns Tissue Harmonic Imaging on and off.
5 Depth Depth Adjusts the imaging depth for 2D.

Depth Up Decreases imaging depth.
Depth Down Increases imaging depth.
6 Zoom Magnifies image 2x.
7 Gain Near Adjusts the gain applied to the near field of the image.
Far Adjusts the gain applied to the far field of the image.
Gain Adjusts the overall gain applied to the entire image.
8 AC power A steady green light indicates AC power is connected. A flashing green light
indicator indicates the system is in sleep mode.
Chapter 4: Setup and Operation 21

Table 4.1: System Controls (Continued)
Number System Control Description
9 Caliper/Calcs Caliper activates a measurement caliper on the screen.

Calcs turns the calculation menu on and off.
10 Touchpad Use to select, adjust, and move objects on the screen.
11 Select Use to switch among touchpad control for line position (2D), text position
(text), calipers for measurement (calipers), pictograph marker position/angle
(picto), arrow position/orientation (arrow).
12 Print Prints the active image to the printer.
13 Save Saves an image to the CompactFlash card.
14 Remappable Controls features on the context menu which are adjusted based on the system
controls state.
15 Forms Setup Access to the system settings.

Report Access to the patient report.
Review Access to the patient list and saved patient images.
Patient Access to patient information.
16 (Delta key) Use as a shortcut to existing functionality in the system.
17 Video recording Record Turns VCR record on and off.

Save Clip (Available on future releases.)
18 Freeze Freeze Stops the live imaging and displays a frozen image.
Cine Review images stored in the cine buffer; (back/forward)
back/forward through last-in, first-out sequence.
All mode images can be stored and reviewed in
the cine buffer.
19 Update Toggles between image modes in M Mode and Doppler, e.g., between Doppler
sample line and Doppler spectral trace.
20 Modes M Mode Turns M Mode on and off.

Doppler Turns Doppler on and off.
Color Turns CPD/DCPD on and off.
2D Turns 2D on and off.
4.2 System Components

The SonoSite system components are identified in “About the System” on page 2.
22 Chapter 4: Setup and Operation

4.3 Setup
Key click 1 Press the Setup key.
2 Select Audio, Battery from the on-screen menu.
3 In the Key click list, select On or Off.
Beep alert 1 Press the Setup key.

3 In the Beep alert list, select On or Off.
Sleep delay 1 Press the Setup key.

3 In the Sleep delay list, select Off, 5, or 10 minutes.
Power delay 1 Press the Setup key.

2 Select Audio, Battery, from the on-screen menu.
3 In the Power delay list, select Off, 15, or 30 minutes.
OB Authors 1 Press the Setup key.

2 Select Calculations from the on-screen menu.
3 In OB Authors list, select the desired OB authors.
Date 1 Press the Setup key.

2 Select Date and Time, Presets from the on-screen menu.
3 In the Date field, enter the current date (year, month, and day).
Time 1 Press the Setup key.

3 In the Time field, enter the current time in 24 hour format (hours and
minutes).
Delta Key 1 Press the Setup key.

2 Select Delta Key, F Keys from the on-screen menu.
3 Select desired functionality for the Delta key.
The Delta key will now control this function.
F Keys 1 Press the Setup key.

2 Select Delta Key, F Keys from the on-screen menu.
3 Type in desired text. Use the Backspace key or Delete key to correct
mistakes.
Patient Header 1 Press the Setup key.

2 Select Display Information from the on-screen menu.
3 Select the desired check boxes to display desired information in the patient
header.
Mode Data 1 Press the Setup key.

3 Select the desired check boxes to display imaging information on the screen.
System Status 1 Press the Setup key.

3 Select the desired check boxes to display the system status on the screen.
Doppler Scale 1 Press the Setup key.

3 In the Doppler Scale list, select cm/s or kHz.

Duplex 1 Press the Setup key.
2 Select Presets from the on-screen menu.
3 In the Duplex list, select desired image display.
• Full 2D, Full Trace
• 1/3 2D, 2/3 Trace
• 1/2 2D, 1/2 Trace
Printer 1 Press the Setup key.

3 In the Printer list, select the desired printer from the list of recommended
printers.
Thermal Index 1 Press the Setup key.

3 In the Thermal Index list, select TIS, TIB, or TIC.
Video mode 1 Press the Setup key.

3 In the Video mode list, select NTSC or PAL.
Connectivity 1 Press the Setup key.

2 Select Presets from the on-screen menu.
3 In the Connectivity mode list, select SiteLink or DICOM.
After changing connectivity, a dialog box is displayed to restart the system.
Note: SiteLink and DICOM are optional features.
System Information 1 Press the Setup key.

2 Select System Information from the on-screen menu.
Note: To install a license key see “Installing a License Key” on page 34.
Reset To return settings for this setup page to factory default, select Reset from the
on-screen menu.
Press the Setup key to exit.
4.4 Touchpad
The touchpad is used to select, adjust, and move objects on the screen. For example, it controls the caliper
position, CPD/DCPD box position, floating cursor, and more.
Note: The arrow keys control much of the same functionality as the touchpad.
4.5 Accessories
For information about accessories and other SonoSite products, refer to the user guide for each product.

4.6 Preparing the System for Operation
4.6.1 Installing and Removing the Battery

Caution: Use only the specified SonoSite battery pack. For battery safety notes, see “Battery Safety” on
page 6.
The system can be powered from either a battery pack or external power.
The battery pack is a 6-cell, 11.25V (nominal), 4.4 amp-hour, Lithium-Ion, rechargeable battery pack.
The battery comprises six lithium-ion cells plus electronics, a temperature sensor, and battery contacts.
If the battery is being installed for the first time, it will need to be charged.
Warning: To avoid injury to the operator and to prevent damage to the ultrasound system, inspect the
battery for leaks prior to installing.
Locking levers
Figure 4.2 Insert Battery into System
To install the battery:

1 Turn the system upside down.
2 Place the battery into the battery compartment, at a slight angle. See Figure 4.2.
3 Slide the battery forward until it locks into place.
4 Push down on the two locking levers to secure battery.
To remove battery:
1 Push up on the two locking levers.
2 Slide the battery back.
3 Lift the battery from the compartment.

4.6.2 Using AC Power/Charging Battery
The battery charges when the system is connected to the AC power supply. If the system is off and connected to
AC power, a completely discharged battery will fully charge in 2.5 to 3.5 hours. If the system is on and connected
to AC power, a completely discharged battery will fully charge in 5 to 6 hours.
The system can run on AC power or charged battery in three ways.
• Connected directly to the system
• Connected to the mini-dock (see “To operate the system using AC power (directly to system):” on page 26)
• Connected to the mobile docking system (see “To connect AC power using the mini-dock:” on page 27)
To operate the system using AC power (directly to system):

Caution: Verify the hospital supply voltage corresponds to the power supply voltage range. See
“Electrical” on page 18.
1 Connect the DC power cable from the power supply to the connector on the system. See Figure 1.2 on page 3.
2 Connect one end of the system AC power cord into the power supply. Then plug the other end into a
hospital-grade electrical outlet.
4.6.2.1 Battery Charge Indicators

The Battery Charge Indicator, a battery icon located on the upper right hand section of the display, indicates the
current battery level.
• All Battery Indicator segments lit mean the system battery is fully charged.
• Some Battery Indicator segments lit mean the system battery is partially charged.
• When the battery is charging the Battery Indicator segments light sequentially.
Table 4.2 contains the charging specifications for the system.
Table 4.2: System Charging Specification
System Charging Parameter Specification
Charge time to 80% capacity, with System power off 3 hours @ 25° C
Charge time to 80% capacity, with System power on 6 hours @ 25° C

4.6.3 Connecting to AC Power
Mini-Dock
Power Supply
A H
To I
PC
Power To
Ethernet
Strip
B D
Printer
Remote Video- In Out
E F
AC In
C
Power
Out
VCR
Audio Video Audio Video Dip switches
In In Out Out 1-4 Down
AC 5,6 Up
Power RS 232
S-Video Composite
To AC Power AC In
(wall outlet)
Figure 4.3 Printer and VCR Connectivity
To connect AC power to the docking system:

Note: The AC power cord to the power supply and the DC power cord from the power supply are preinstalled.
1 Remove back panel.
2 Connect the system AC power cord to the power strip on the top shelf of the mobile docking system.
A country specific AC power cord is provided.
3 When ready to use, route the AC power cord out the back, and replace the back panel.
4 Connect the system AC power cord to a hospital-grade electrical outlet.
To connect AC power using the mini-dock:

1 Insert the ultrasound system into the mini-dock.
2 Connect the DC power cable from the power supply to the connector on the mini-dock.
3 Connect one end of the system AC power cord into the power supply. Then plug the other end into a
hospital-grade electrical outlet.

4.6.4 Connecting and Removing Transducers
Warning: The transducer connector can become hot during operation. This is normal. Operate the system
in the docking system or on a flat, hard surface to allow air flow past the connector.
Caution: The electrical contacts inside the system transducer connector may be damaged by foreign
material. Keep foreign material out of the connector.
Figure 4.4 Connect the Transducer
To connect the transducer:

1 Turn the system upside down (if not in docking system).
2 Pull the transducer latch up and rotate it clockwise.
3 Align the transducer connector with the connector on the bottom of the system.
4 Insert the transducer connector into the system connector.
5 Turn the latch counterclockwise.
6 Press the latch down, securing the transducer connector to the system.
To remove the transducer:

1 Pull the latch up and rotate it clockwise.
2 Pull the transducer connector away from the system.
4.6.5 Turning the System On and Off
To turn the system on/off:

Caution: Do not use the system if an error message appears on the display. Note the error code and turn
off the system. Call SonoSite or your local representative.
1 Locate the Power key on the top left side of the system. See Figure 4.1 on page 21.
2 Press the Power key once to turn on and once to turn off.
To wake up the system:

To conserve battery life, the system is configured to go into sleep mode. The system goes into sleep mode when
the lid is closed or if the system has not been touched for a preset amount of time. Press any key, touch the
touchpad, open the lid to wake up the system. To adjust the time for sleep delay, see “Sleep delay” on page 23.

4.7 Upgrading the System Software
As described in “About the System Software” on page 4, software upgrades are provided on CompactFlash
cards, which are installed in the back CompactFlash slot on the right hand side of the system. Upgrades provided
may be required or optional.
Whenever you install a CompactFlash card containing a newer version of software into the system, the system
will determine the level of software, prepare the system for the upgrade, and then install the new software onto
the system.
When a CompactFlash card contains new transducer software and the transducer that requires a software
upgrade is connected, the system prompts the user that the transducer requires the upgrade.
To upgrade the system software:

Caution: To prevent loss of data or loss of images, transfer all images on the CompactFlash
card before performing the upgrade. Images remaining on the CompactFlash card
cannot be viewed or deleted after the upgrade.
Note: If you use SiteLink Image Manager for transferring images, SiteLink 2.1 is required after the upgrade. Contact the
Technical Support Department to receive a new version of the program.
1 Remove any transducer or Triple Transducer Connect from the Titan system.
2 Connect the Titan system directly to the power supply or through the docking system/mini-dock. See
“Connectivity” on page 73.
3 Insert the CompactFlash card into the back slot.
The system displays the following message:
Figure 5 Upgrade System Software
4 Select Yes to accept or No to cancel the upgrade.

When you accept the system software upgrade, the system begins to load the new software and prepare for
the upgrade and displays the following message:

Figure 6 System Software Loading
When the software upgrade has prepared the system for upgrade, the system displays the following
message:
Figure 7 System Software Step 1 Restart
5 Select Restart.
After restart, there is a short delay before the system goes into the upgrade process. Do not turn the system
off. The system displays the following message:
Figure 8 System Software Installation

When the system software upgrade is completed, the system displays the following message:
Figure 9 System Software Step 2 Restart
6 Select Restart.
When the operating software has been replaced, the system presents you with the license update screen so
that you may license the software. If upgrading a transducer, press Cancel from the on-screen menu.
Figure 10 System Software License Key
At this point, the software upgrade process is complete, but the software is not yet licensed. See“Obtaining
a License Key” on page 34.
Note: If you are upgrading a system and one or more transducers, it is recommended that all items be upgraded before
calling SonoSite Technical Support for your license keys. To postpone obtaining a license key, press Cancel from the
on-screen menu.

To upgrade transducer software:
1 Attach a transducer to the system and insert the CompactFlash card in the back slot.
Figure 11 Incompatible Transducer Update
This screen is not displayed for compatible transducers.
Figure 12 Upgrade Transducer Software
2 Select Yes to accept or No to cancel the upgrade.

When you accept the transducer software upgrade, the system loads the new software and displays the
following message:
Figure 13 Transducer Software Loading

When the system software upgrade is completed, the system displays the following message.
Figure 14 Transducer Software Installation
3 Select Restart.
When the transducer software has been replaced, the system presents you with the license update screen so
that you may license the software for your transducer. Upgrade all transducers before obtaining license keys.
Repeat all steps in “To upgrade transducer software:”
Figure 15 Transducer License Screen
At this point, the software upgrade process is complete, but the software is not yet licensed. The following
section “Obtaining a License Key” explains how to license your system and transducer software.
Note: If you are upgrading additional transducers, it is recommended that all items be upgraded before calling
SonoSite Technical Support for your license keys. To postpone obtaining a license key, press Cancel from the on-screen
menu.

4.7.1 Obtaining a License Key
A license key is required to update your system. It may be obtained by contacting SonoSite, Inc. Technical
Support Department.
Technical support 1-877-657-8118
International technical support: Contact your local representative or call 425-951-1330
Technical support fax: 1-425-951-6700
Technical support e-mail: [email protected]
SonoSite website: www.sonosite.com and select Technical Support under Special

Features
To receive your license key, you will need to provide the following information, which is displayed on the system
information screen of your system:
• Name of the person installing the upgrade
• System serial number (located on the bottom of your system)
• ARM version
• PCBA serial number
4.7.2 Installing a License Key

When you have obtained a license key for your software, you must enter it into the system. Once a valid license
key has been entered, the system remains licensed until the next time the system software is upgraded.
1 Turn on the system.
If the software is not yet licensed, the license update screen displays.
The license update screen displays the following information: how to contact SonoSite, and the required
information to obtain the License Update number, and the grace period (time remaining) on your system.
Figure 4.1 System and Transducer License Screens
Note: The software versions on your system may vary based on your upgrade and configuration.
2 Enter your license key in the license number field.
If the license key that you entered is recognized by the system as being valid for your system and the software
you installed, Done appears on-screen.
3 Select Done from the on-screen menu to install the license key and license your software.
If the license key that you entered is not recognized by the system, the Cancel button remains on the screen
as long as the defined grace period has not expired.
If the grace period has expired, the menu item will indicate this by showing zero hours remaining in the grace
period. At this point, you must then enter a valid license key before you can use the system.

Note: If you have entered a valid license key and you cannot complete the licensing procedure, verify that the license key
has been entered correctly. The license key should be exactly 12 digits (for example, 123348990552) with no other
characters or punctuation.
Note: If after confirming correct entry of the license key, you are still unable to license your system, call SonoSite technical
support. USA/Canada customers call 1-877-657-8118. International customers call your local representative or
1-425-951-1330.
If the system is on and the grace period expires, the license update screen must be displayed from the system
information screen. See “System Information” on page 24.
4.7.3 To Display the System Information Screen

1 Press the Setup key.
The system information screen displays the following information: Product, Modes, Previous License Update,
Boot Version, ARM Version, DSP Version, PCBA Serial Number, PLD, CPLD Version, SH Database Version, and
SH Serial Number.
Note: The software versions on your system may vary based on your upgrade and configuration.
Figure 4.2 System Information Screen
4.7.4 To Display the License Update Screen

1 Press the Setup key.
3 On the lower section of system information screen, select the button under License.
The license update screen displays.
4 Perform the steps in “Installing a License Key” on page 34.
Figure 4.3 Setup Screen: License Key

Chapter 5: Cleaning and Disinfecting
5.1 Universal Precautions

SonoSite recommends that personnel who have regular exposure to medical devices returned for service practice
“universal precautions.” Universal precautions are an approach to infection control. Those servicing this product
should follow the prescribed standards for their area.
5.2 Receipt of Suspected Contaminated Materials

SonoSite recommends that personnel who have regular exposure to medical devices returned for service practice
“universal precautions.” Universal precautions are an approach to infection control. Those servicing this product
should follow the prescribed standards for their area.
If visual inspection suggests possible contamination when opening a product returned for service, take proper
steps to contain the contamination. Wear necessary Personal Protective Equipment (PPE) (gloves, masks, and
gowns) when opening or examining a suspect package.
Before transfer to a service area, label the suspect package “contaminated” and seal it to prevent exposure.
Discard any packing materials removed from a package suspected of contamination in a biohazard container.
Discard any contaminated materials received with the product in an appropriate biohazard container.
Contaminated materials may include biohazardous waste and sharps.
Maintain a disinfecting agent in case any work surface is contaminated. The recommended agent is 0.5% sodium
hypochlorite (bleach) solution. To prepare the agent, mix one part household bleach (5.25% - 6% sodium
hypochlorite) to nine parts water. Spray or wipe the solution onto the work surface and allow to air dry.
Please use these recommendations when cleaning or disinfecting your ultrasound system, transducers, and
accessories. This chapter assists in effective cleaning and disinfection, but it is also intended to protect the system
and transducers against damage during cleaning or disinfection.
For more information about cleaning or disinfecting solutions or ultrasound gels for the transducer, call SonoSite
technical support or your local representative. For information about a specific product, call the product
manufacturer.
5.3 Recommended Disinfectants

For a list of disinfectants recommended for use on the system and transducers, see the TITAN Ultrasound System
User Guide.
Chapter 5: Cleaning and Disinfecting 37

38 Chapter 5: Cleaning and Disinfecting
Chapter 6: Troubleshooting
6.1 Basic Troubleshooting

This chapter contains information to help you correct problems with system operation and provides instructions
on the proper care of the system, transducer, and accessories.
If you encounter difficulty with the system, use the information in this chapter to help correct the problem. If the
problem is not covered here, contact SonoSite technical support at the following numbers or addresses:

Features
Table 6.1: Troubleshooting
Symptom Solution
System will not power on. Check all power connections.

Perform the following sequence: remove DC input connector and
battery; wait 10 seconds; connect DC input or install battery; press the
power key.
Ensure the battery is charged.
System image quality is poor. Adjust the LCD screen to improve viewing angle.
Adjust the brightness, as necessary, to improve image quality.
Adjust the gain.
Zoom does not work. Press Freeze key. Zoom does not work when the image is frozen.
No CPD image. Adjust the gain.
No DCPD image. Adjust the gain.
No OB measurement selections. Select the OB or Gyn exam type.
Print does not work. Set the correct printer in system setup.
Check the printer connections.
Check the printer to ensure that it is turned on and set up properly. See
the printer manufacturer’s instructions, if necessary.
VCR does not record. Check the VCR connections.

Check the VCR to ensure that it is turned on and set up properly. See
the VCR manufacturers’ instructions, if necessary.
External monitor does not work. Check the monitor connections.

Check the monitor to ensure that it is turned on and set up properly.
See the monitor manufacturers’ instructions, if necessary.
Unexpected labels using the Ensure labels have been assigned to the function keys.
function keys.
Chapter 6: Troubleshooting 39
Table 6.1: Troubleshooting (Continued)
Symptom Solution
Inaccurate fetal age calculation. Ensure that the patient information, date, and time are set accurately.
System does not recognize the Disconnect and reconnect the transducer.
transducer.
Text cursor does not move when Text cursor is constrained to one line.
touchpad or arrows are selected.
This icon indicates that system maintenance may be required. Record

A maintenance icon displays
the number in parentheses on the C: line and contact SonoSite or your
on the system screen. SonoSite representative.
6.2 Periodic Maintenance

There is no recommended periodic or preventive maintenance required for the system, transducers, or
accessories. There are no internal adjustments or alignments required. There are no functions that require
periodic testing or calibration. All maintenance and/or performance tests are described in Chapter 8,
“Performance Testing” of this manual. Performing maintenance activities not described in this manual may void
the product warranty.
Local regulations may require electrical safety testing.
Contact SonoSite Technical Support for any maintenance questions.
6.3 System and Subsystem Diagnosis

This section covers basic diagnostic and troubleshooting procedures you may follow if the system does not
operate properly. To diagnose system failures, consult the referenced diagnostic figures that follow or the
SonoSite Technical Support department.
Table 6.2: Troubleshooting Subassemblies and Diagnostic Figures
Subassemblies Diagnostic Figures or Table
Display Figure 6.2
Control Panel Figure 6.3
System Figure 6.4
Battery Figure 6.5
Mini-Dock/Mobile Docking System Figure 6.6 and Figure 6.7
Triple Transducer Connect Figure 6.8
DICOM Table 6.3
40 Chapter 6: Troubleshooting
6.4 System Repair
The system is repairable through subassembly replacement or through replacement of parts as recommended by
SonoSite in Chapter 7, “Replacement Procedures” of this manual. Component level repair of Printed Circuit
Board Assemblies is performed only at the SonoSite repair facility. Replacement of board level components by
unauthorized service facilities voids the SonoSite warranty.
6.5 Test Equipment

Test equipment is not required for this troubleshooting section. Troubleshooting test aids include an external
monitor and a spare battery.
6.6 Failure Modes
6.6.1 Display
An easy method to verify display failures is to attach an external monitor to any of the external video connectors
on the mini-dock. For example, if the system display is blank and the external monitor works properly, the
system display requires servicing. If the system display works correctly and the external monitor is blank then
either the mini-dock or the external display is at fault.
Follow the Display Flow Diagram (Figure 6.2) to evaluate the cause of failure.
6.6.2 Control Panel

An easy method to verify keyboard failures is to go to the patient information screen by pressing the Patient Key
and press each individual key on the keyboard. Press function keys and note their response.
Follow the Control Panel Flow Diagram (Figure 6.3) to evaluate the cause of failure.
6.6.3 System/Main PCBA

The main PCBA may present symptoms that are difficult to assess. Main PCBA failures typically result in “assert
codes” that are output to the display. If an assert code should display, note the assert code and contact SonoSite
technical support to clarify the failure. Figure 6.1 shows an assert code and a maintenance icon displayed on the
system screen.
Follow the System Flow Diagram (Figure 6.4) to evaluate the cause of failure.
Assert code
Figure 6.1 Assert Screen
6.6.3.1 Clearing a System Assert Code
After the assert code has been recorded, power down the system.
1 Press the Power key on the system and release it.
2 Turn the power back on to check if the fault cleared or if the condition remains.
If the condition cleared, you may use the system. If the condition remains, corrective action must be taken
before the system can be used. Contact SonoSite Technical Support for assistance or repair parts.
3 If the Power key is not functional, all sources of power must be removed to allow the system to power down.
6.6.4 Battery
If the system does not operate or does not run for the expected duration for a given charge, battery failure may
have occurred.
Follow the Battery Flow Diagram (Figure 6.5) to evaluate the cause of failure.
6.6.5 Mini-Dock/Mobile Docking System

Electrical failures for the Mini-Dock and Mobile Docking System are the same. Follow the troubleshooting
diagrams (Figure 6.6 and Figure 6.7) to isolate failures with these products.
6.6.6 DICOM
A DICOM troubleshooting chart is provided as Table 6.3.
6.7 Troubleshooting Flow Diagrams
6.7.1 Display
Figure 6.2 Display Flow Diagram
6.7.2 Control Panel
Figure 6.3 Control Panel Flow Diagram
6.7.3 System
Figure 6.4 System Flow Diagram
6.7.4 Battery
Figure 6.5 Battery Flow Diagram
6.7.5 Mini-Dock/Mobile Docking System
Figure 6.6 Mini-Dock and Mobile Docking System Flow Diagram, Part 1
Figure 6.7 Mini-Dock and Mobile Docking System Flow Diagram, Part 2
6.7.6 Triple Transducer Connect
Figure 6.8 Triple Transducer Connect Flow Diagram
Table 6.3: DICOM Troubleshooting
Error Message Error Code Cause Troubleshooting
Socket TSOCKET_CONNE Invalid network 1) Using Ping, verify that the Printer/Archivers is
communication CT_FAILURE configuration. connected. If Ping fails:
failed Wrong port number. a) Check the devices IP address.
Application is not b) Check the Titan's IP address, Subnet mask, and
running. Gateway IP address.
Printer is offline. If Ping is OK:
2) Using Verify, check to see if device is available. If
Verify fails:
a) Check the Printer/Archivers Port configuration
on the Titan.
b) Insure that the Printer is online and the
Archivers application is running.
Archiver TDICARCH_OPEN_ Wrong Capture Type Verify that the Archiver supports the selected
transaction FAILURE Selected Capture Type setting. E.g. US Image, SC Image or
failed US-Ret Image.
Printer TDICPRNT_OPEN_ Wrong Image Verify that the Printer supports the selected Image
transaction FAILURE Setting settings. E.g. Color (RGB) or Grayscale (Monochrome)
failed
DICOM network TDNETWORK_OPE Device does not Verify that Titan AE Title or IP address has been
communication N_FAILURE recognize Titan, correctly configured on the Printer/Archiver. Note:
failed rejects association some devices require that the Imaging modality
(Titan) be recognized in order to accept images. This
requires configuration on the device.
Internal failure TDNETWORK_REA Invalid DICOM Check Titan Printer DICOM settings for correctness
detected D_FAILURE Attribute (e.g. film size, format, etc.)
Chapter 7: Replacement Procedures
7.1 Display Replacement

Note: Consult Chapter 6, “Troubleshooting” before making any repairs.
7.1.1 Required Parts

Service Assembly, Display, TITAN (P03861)
7.1.2 Required Tools

• #1 Phillips screwdriver
• Torque screwdriver, 2.0–10.0 inch pounds (0.23–1.1 newton meter)
• 8 mm nut driver
• An anti-static mat
• A wrist grounding strap
Caution: Always use correct ESD procedures. ESD damage is cumulative and may not be noticeable at
first. Initial ESD symptoms may be slightly degraded performance or image quality.
7.1.3 Display Removal

1 Remove the battery from the system. See Section 4.6.1, “Installing and Removing the Battery,” on page 25 for
battery removal.
2 Remove the two screws from the back of the system per Figure 7.1.
Screws (2)
Figure 7.1 System Rear
3 Lay the system on the top and remove the two screws from the bottom of the system per Figure 7.2.
Chapter 7: Replacement Procedures 51

Screws (2)
Figure 7.2 System Bottom
4 Turn the system over, fully open the display, and lift off the Control Panel per Figure 7.3.
Figure 7.3 Control Panel Removal
52 Chapter 7: Replacement Procedures

5 Disconnect the two connectors from the display to the Main PCBA per Figure 7.3.3.5.
Connectors (2)
Figure 7.4 Display Connectors
6 Remove the four screws from the Display Hinges per Figure 7.5.
Screws (4)
Figure 7.5 Display Screws
7.1.4 Display Replacement

1 Set the new display in place.
2 Install the four screws that hold the Display in place. Torque the screws to 5.5 inch pounds.
3 Connect the two connectors that connect the Display to the Main PCBA.
4 Place the Control Panel in place.
5 Reinstall the four screws that hold the Control Panel in place. Torque the screws to 5.5 inch pounds.

7.1.5 Test the Display
1 Replace the battery, attach an external power supply, or attach a mini-dock.
2 Press the Power key to apply power to the system.
3 Verify the display operates correctly.
7.2 Control Panel Subassembly Replacement

• P03862 Service Assembly, Control Panel TITAN, English or
• P03863 Service Assembly, Control Panel TITAN, English, International, or
• P03864 Service Assembly, Control Panel TITAN, French, or
• P03865 Service Assembly, Control Panel TITAN, German, or
• P03866 Service Assembly, Control Panel TITAN, Italian, or
• P03867 Service Assembly, Control Panel TITAN, Spanish, or
• P03868 Service Assembly, Control Panel TITAN, Portuguese

• 8 mm nut driver
7.2.3 Control Panel Removal

1 Remove the two screws from the rear of the system per Figure 7.1.
2 Remove the two screws from the bottom of the system per Figure 7.2.
3 Turn the system over, fully open the display, and lift off the Control Panel per Figure 7.3.
7.2.4 Control Panel Replacement

1 Place the new control panel in place.
2 Install the four screws removed in Section 7.2.3. Torque the screws to 5.5 inch pounds.

7.3 Main System Disassembly for Repair and/or Replacement

Parts for the Main System Repair could include any of the following
• P03871 Service Assembly Main PCBA, TITAN
• P03870 Service Assembly Power Supply, TITAN
• P03869 Service Assembly TGC, TITAN
• P03872 Service Assembly Speaker, TITAN
• P03873 Service Assembly Upper Enclosure, TITAN
• P03874 Service Assembly Lower Enclosure, TITAN
Note: Replacing the enclosure bottom requires printing a new label for the product. This must be printed prior to
shipping the enclosure bottom. You will be required to provide the information to print this label.
• Nest Frame Assembly, TITAN (order these parts individually)
• P00364 Connector, Interposer
• P00524 Screw, Shoulder, Thrust Plate
• P00353 Wear Plate
• P00646 Spring, Thrust Plate
• P02860 Nest Plate, Interposer
• P00352 Shield, Perimeter, Long
• P00527 Shield, Perimeter, Short
• P02861 Post, Mounting

• 8 mm nut driver
7.3.3 Main PCBA Removal

1 Remove the display and the control panel from the system following the removal procedures in Section 7.1.3
and Section 7.2.3.
2 Remove the additional 4 screws from the bottom of the system per Figure 7.6.

Screws (4)
Figure 7.6 Bottom Screws
3 Turn the system over and remove the top enclosure from the main PCBA. This exposes all of the replaceable
parts for the main system per Figure 7.7.
Main PCBA
Nest frame
assembly
Power supply
TGC assembly
Speaker Speaker
Figure 7.7 System Components

7.3.3.1 Speaker Replacement
1 Press on the connector release and pull the connector out of the receptacle.
2 Gently pry off the retaining clip with a flat bladed pry tool. See Figure 7.8.
Connector
Retaining clip
Figure 7.8 Speaker Replacement
7.3.3.2 Power Supply

1 Gently pry the shield from the power supply and set it aside. This part will be used in reassembly. Note that
the shield fits only one way. See Figure 7.9.
Power supply
shield
Figure 7.9 Power Supply Shield
2 Remove the 7 screws that hold down the power supply PCB per Figure 7.10.

3 Gently lift the power supply and shield assembly away from the Main PCBA.
Screws (7)
Figure 7.10 Power Supply Screws

7.3.3.3 TGC PCBA
1 Remove the TGC knobs identified in Figure 7.11.
TGC knobs (3)
Figure 7.11 TGC Knobs
2 Remove the flex cable from the TGC PCB by lifting on the flex release tab. See Figure 7.12.
3 Remove the flex cable from the Main PCBA by lifting gently on the flex release tab.
4 Remove the two screws holding the TGC PCBA in place.
Release tabs Screws (2)
Figure 7.12 TGC Removal

7.3.3.4 Main PCBA
1 Remove the 3 screws holding the Main PCBA in place per Figure 7.13.
2 Remove the 4 shoulder bolts holding the transducer nest frame assembly in place. As you remove the nest
frame assembly from the PCBA tilt the PCBA and enclosure to almost vertical to avoid spilling the Interposer
Connectors from the Assembly.
3 Disconnect the speaker wires from the Main PCBA.
4 Remove the TGC PCBA following the procedure in Section 7.3.3.3.
Screws (3)
CompactFlash
release buttons
Shoulder bolts (4)
Figure 7.13 Main PCBA Screws
5 Lift on the edge of the Main PCBA closest to the system handle.
Note: As the Main PCBA is removed press in on the CompactFlash release buttons so they clear the opening in the bottom
enclosure.
7.3.3.5 Main PCBA Replacement

Replace the Main PCBA by following the reverse of the removal procedure. Do not tighten all the screws until
everything is in place.
1 Replace the Main PCBA.
2 Replace the Nest Frame Assembly.
3 Reconnect the speaker wires.
4 Replace the power supply assembly.
5 Replace the TGC assembly.
6 Reinstall the shield to the Power Supply.
7 Tighten all screws to their specified torque of 5.5 inch pounds.

Chapter 8: Performance Testing
8.1 Overview
Warning: Critical Test Function — A failure of the system functions tested in this section could affect
safety or effectiveness of the system adversely. While performing the steps in this section, verify
that the images on the system display and on the external monitor are acceptable.
• Verify that all controls operate smoothly over their full range and that the system responds properly.
• To obtain 2D images, SonoSite recommends using the RMI 413A Soft Tissue Phantom or the RMI 403 GS
Multipurpose Phantom. Any equivalent Phantom is acceptable.
• To obtain Power Doppler images, SonoSite recommends using the RMI 425 Doppler Phantom or the RMI
1425A Doppler Phantom. Any equivalent Phantom is acceptable.
• When making penetration measurements on a phantom, apply the phantom reference value and tolerance
to the measurement.
8.2 Test Equipment

• SonoSite ultrasound system under test
• C60/5-2 MHz transducer
• C15/4-2 MHz transducer
• RMI 413A Soft Tissue Phantom, RMI 403 GS Multipurpose Phantom, or the equivalent
• RMI 425 Doppler Phantom, RMI 1425A Doppler Phantom, or the equivalent
• Video Printer
• External Monitor
• Acoustic gel
8.3 Setting Up Performance Tests
To set up the performance tests:

1 Attach the C60/5-2 MHz transducer to the system.
2 Select general for optimization and OB for exam type.
3 Couple the transducer to the phantom, adjusting gain settings and transducer for a proper phantom image
(e.g., pins are high-level echoes positioned in straight lines; cysts are sonolucent, edges are sharp, and
graphite particles of the phantom are mid-grays).
8.3.1 Scan Reference Orientation
To set up the scan reference orientation:

1 Verify that the correct transducer name appears in the upper right corner of the system display.
2 Verify that the scan plane orientation mark in the image located near the skinline corresponds to element #1
on the transducer. To test, put your finger on the probe and run it across the transducer face. Your finger
touching the transducer face should appear at the orientation mark on the display image format.
3 With the array pointing down and the orientation mark to the operator’s left, element #1 corresponds with
the left side of the array.
Chapter 8: Performance Testing 61

8.4 Testing 2D Performance
To test 2D performance:
1 Use a C60/5-2 MHz transducer in 2D mode.
2 Adjust the position of the C60/5-2 MHz transducer on the phantom.
3 Use the 2D system controls to obtain a clear image that shows both the horizontal and vertical rows of pins.
8.4.1 2D Image Quality
To test 2D image quality:

1 Verify that the ultrasound image appears uniform in both the axial and lateral direction, with no dropouts
or intensity variations.
2 Verify that the cystic structure at the focal zone is clearly differentiated from the surrounding tissue and is
echo-free, while solid tissue, with numerous echo sources, appears solid.
8.4.2 Axial Measurement Accuracy

Note: Measurements must be performed while the image is frozen.
To set up axial accuracy:

1 Acquire the image.
2 Press the Freeze key.
3 Press the Caliper key. The caliper appears on the image display. The screen menu indicates Cal 1, Cal 2, and
Ellipse. (If the caliper line setup is on, then a dotted line connects the two calipers. See the TITAN Ultrasound
System User Guide, if necessary.) The Cal 1 caliper is active by default.
4 Use the touchpad to position one of the calipers.
5 Press the Select key to fix the caliper and enable the other caliper.
6 Use the touchpad to move the other caliper. The results update as you move the caliper, and the
measurement is complete when you finish moving the calipers. (Press the Select key to alternate the active
caliper, and adjust the measurement with the touchpad.)
7 To perform another distance measurement on the image, select the other distance icon and repeat the
preceding steps.
To test axial accuracy:

1 Measure the distance, center to center, of any two pins that are 5-12 cm apart vertically.
2 Verify that the distance measured is within the tolerance listed in Table 8.1.
62 Chapter 8: Performance Testing

8.4.3 Lateral Measurement Accuracy
To set up the lateral measurement accuracy:

Perform steps 1 through 7 in Section 8.4.2.
To test the lateral measurement accuracy:

1 Measure the distance, center to center, of any two pins that are 4-10 cm apart horizontally.
2 Verify that the distance measured is within the tolerance listed in Table 8.1.
3 Press the Freeze key to return the system to live 2D mode.
Table 8.1: System Measurement Accuracy
Measurements Tolerance
Axial Distance +/- 2%
Lateral Distance +/- 2%
8.4.4 Penetration
To test penetration:
1 Adjust the system controls to obtain a clear image that shows the limits of echo penetration as shown in
Table 8.2.
2 Measure from the center of the skinline to the deepest vertical position—where the scatter echoes start to
break up and tissue definition is lost.
Table 8.2: Imaging Performance
Imaging Performance C60 ICT C15 L38 C11
2D Penetration 11.5 cm 5.0 cm 19.0 cm 6.0 cm 5.0 cm

8.5 Additional Performance Tests
8.5.1 CPD
To test CPD:
Note: Use the RMI 425 Doppler Phantom or the RMI 1425A Doppler Phantom.
1 Connect any transducer and set up the system for CPD mode.
2 Acquire the image.
3 Press and release the Color key for CPD/DCPD mode. Select CPD from the on-screen menu. A Region of
Interest (ROI) box is displayed on top of the grayscale image. (Press the 2D key to return to 2D imaging.)
To move the CPD image:

• Use the touchpad to move the CPD ROI. While you are moving the CPD ROI, you will see an outline of the
new position moving on the display. When you stop moving, the new position will display the CPD ROI.
(The size of the CPD ROI is fixed. There is no control to change it.)
To adjust CPD gain:

Turn gain clockwise to increase the amount of CPD gain. (While in CPD imaging, near and far affect only the 2D
image; they do not affect the CPD image.)
Turn gain counterclockwise to decrease the amount of CPD gain.
1 Image the vessel using a Doppler phantom. Verify that as the gain controls increase and decrease, Doppler
echo intensity increases and decreases to correspond. Verify that no flow exists outside the vessel.
2 Save a CPD image by pressing the Freeze key and then the Save key.
8.5.2 Directional Color Power Doppler (DCPD)
To test DCPD:
Note: Use the RMI 425 Doppler Phantom or the RMI 1425A Doppler Phantom.
1 Set up the system per Section 8.5.1 for CPD mode.
2 Select DCPD. Press DCPD on the on-screen menu while in CPD mode. A Region of Interest (ROI) box is
displayed on top of the 2D grayscale. (Press the 2D key to return to 2D imaging.)
To move the DCPD image:

• Use the touchpad to move the DCPD ROI. While you are moving the DCPD ROI, you will see an outline of
the new position moving on the display. When you stop moving, the new position will display the DCPD
ROI. (The size of the DCPD image is fixed. There is no control to change it.)
To adjust DCPD gain:

• Turn gain clockwise to increase the amount of DCPD gain. (While in DCPD imaging, near and far affect only
the 2D image; they do not affect the DCPD image.)
• Turn gain counterclockwise to decrease the amount of DCPD gain.
1 Image the vessel using a Doppler phantom. Verify that as the gain controls increase and decrease, Doppler
echo intensity increases and decreases to correspond. Verify that no flow exists outside the vessel.
2 Save a DCPD image by pressing the Freeze key and then the Save key.

8.5.3 M Mode Imaging
To test M Mode Imaging:

1 Attach a C60 transducer and acquire an image.
2 Press the M Mode key for the M Mode sample line.
3 Position the M Mode sample line over the image using the touchpad.
4 Press the M Mode key again to turn on M Mode.
5 Select the desired sweep speed from the on-screen menu (slow, med, or fast). The on-screen menu will show
the selected sweep speed.
6 Press the Freeze key to freeze the image. Press it again to return to live imaging.
7 Press the 2D key to return to 2D imaging.
8.5.4 Tissue Harmonic Imaging
To test THI Imaging:

1 Attach the C60 transducer and acquire an image.
2 Set the depth to maximum and note the depth at which echo information is lost.
3 Press the THI key on the control panel so it displays THI on the display. Tissue Harmonic Imaging in now
active.
4 Observe a decrease in dot size and a significant loss in penetration due to the higher frequency. Image
resolution increases.
5 Press the THI key again to turn off Tissue Harmonic Imaging.
8.5.5 Pulsed Wave (PW) Doppler Imaging
To test PW Doppler Imaging:

1 Attach the C15 transducer.
2 Press the Doppler key for the Doppler sample gate.
3 Press the Doppler key again for the Doppler spectral trace.
4 Place a large drop of ultrasound gel on the transducer lens.
5 Gently tap the top of the gel and observe a reflection on the spectral trace and the sound from the speakers.
6 Press the 2D key to return to 2D imaging.
8.5.6 Image Quality Verification Test/Livescan

• Products with replaced subassemblies, or products that have been otherwise disassembled, must undergo
an Image Quality Verification Test/Livescan.
• The Image Quality Verification Test/Livescan should be performed after successfully completing Section 8.3,
“Setting Up Performance Tests,” on page 61 and Section 8.5.1, “CPD,” on page 64.
• The test is completed before returning the system to service.
• A certified sonographer must perform the test.
• The Livescan test performed is at the discretion of the Sonographer and will represent their acceptance of a
successful service event.
8.5.7 Image Review

Review all saved images and verify that the images are displayed properly.

8.5.8 Printer
To test printer operation:

1 Print two images in rapid succession and verify proper operation.
2 Verify that the print control on the system functions correctly.
8.5.9 Battery Charging
To test battery charging operation:

1 Remove the system from the Docking System and insert a battery into the system.
2 Press the Power key to turn the system on. Allow the battery to discharge. The battery indicator icon on the
display, below the Transducer Type indicator, will extinguish from left to right as the battery discharges.
Note: The battery may take 1–2 hours to discharge.
3 Reattach the system to the Docking System and attach the AC power cord to the power connector.
4 Note that the battery indicator indicates that the battery is charging. The sections of the battery indicator will
light sequentially from left to right as the battery charges.
5 If charging is not evident, see Chapter 6, “Troubleshooting” for troubleshooting procedures.
8.5.10 Video Output

Caution: Use only the recommended video monitor, printer, or VCR when verifying the video output at
the video receptacle.
To test the video output:

1 Attach an external video monitor to the video connector using the video cable.
2 Turn on the system power and verify that the video on the external monitor matches the video on the system
display.
If the video does not appear similar, or there is no display on the external monitor, see Chapter 6,
“Troubleshooting” for troubleshooting procedures.

8.6 Returning Products to SonoSite
8.6.1 Contacting SonoSite Technical Support

Features
You will be asked to provide the following information by telephone or e-mail:

• Contact name and phone number
• Product name
• Serial number
• Description of the problem
8.6.2 Shipping Instructions

Please contact SonoSite to get a return material authorization number (RMA). Contact SonoSite before returning
any product.
The shipping address for all returned products is:
SonoSite, Inc.
Attn: Technical Support RMA ___________________
21919 30th Drive SE
Bothell, Washington 98021
USA

This chapter contains information on servicing the TITAN mobile docking system (docking system) and the
TITAN mini-dock. For information about installation and operating instructions for these peripherals consult the
TITAN Ultrasound System User Guide.
9.1 Mobile Docking System

The docking system provides a mobile work platform and recharges the internal battery. The docking system
includes the TITAN mini-dock with connections to an external printer and/or monitors, power supply, USB
connection to SiteLink Image Manager, VGA connection, and S-Video connection. The docking system provides
a storage area for the transducers and other supplies.
1 13
8 14
2 9
3
4
5 10 15
11
12
6
7
Front view Rear view
Figure 9.1 Docking System, Front and Rear Views
Table 9.1: Docking System Features
Number Description
1 Ultrasound system
2 Transducer, connector, and gel storage on both sides of docking system
3 Side panels
(Use to lift, raise, or transport the docking system)
4 Handle release button
Chapter 9: Accessory Service 69

Table 9.1: Docking System Features (Continued)
Number Description
5 Transducer storage
6 Height adjustment pedal

(Press down on foot pedal, grab sides and raise/lower)
7 Locking wheels
(Press down/pull up on locks to lock/unlock)
8 CompactFlash shield
9 Wrist rest/handle
10 Cable hooks
11 Printer bay (black/white only)
12 VCR bay
13 Mini-dock cable cover
14 Mini-dock
15 Storage
To insert system:
1 Push in the handle release button and lift the handle to the upper most position.
2 Close the lid on the ultrasound system and slide into the docking system. Connection will be made when
handle is pushed down.
3 Press the handle down until an audible click is heard.
Warning: To prevent injury, do not use the handle to lift the docking system over an obstacle or threshold.
Use the side panels to lift over an obstacle or threshold.
To remove system:
1 Close the lid on the ultrasound system.
2 Push in the handle release button and lift the handle to the upper most position.
3 Remove the ultrasound system.
70 Chapter 9: Accessory Service

9.2 Mini-Dock
The TITAN mini-dock (mini-dock) provides connectivity for the TITAN ultrasound system when the system is
out of the docking system. The mini-dock provides connections to an external printer and/or monitors, a power
supply, USB connection to SiteLink Image Manager, VGA connection, and S-video connection.
9.3 Connectivity
9.3.1 Connection Panel
Figure 9.2 Mini-Dock Connections
Table 9.2: Mini-Dock Connections
Symbol Definition
DC input
Print control
USB
Flashing yellow LED (Light-Emitting Diode) indicates Ethernet network activity
Ethernet
Solid green LED (Light-Emitting Diode) indicates Ethernet network connection status
RS-232 (VCR control/audio)
S-video out
S-video in (available on future releases)
RGB video out
Composite video out
Audio out
ECG (available on future releases)

9.3.2 Docking System/Mini-Dock Connections
Mini-Dock
Power Supply
A H
To I
PC
Power To
Ethernet
Strip
B D
Printer
Remote Video- In Out
E F
AC In
C
Power
Out
VCR
Audio Video Audio Video Dip switches
In In Out Out 1-4 Down
AC 5,6 Up
Power RS 232
S-Video Composite
To AC Power AC In
(wall outlet)
Figure 9.3 Printer and VCR Connectivity
9.4 Block Diagrams and Schematics
Figure 9.4 Mini-Dock PCB Component Placement

Figure 9.5 TITAN Dock Interface Diagram

Figure 9.6 Mini-Dock Video Distribution

SCL_3V
SDA_3V
page4
page2 page3
CLK_ENCODER
CLK_ENCODER
SCL_3V SCL_3V
CLK_ENCODER
SCL_3V
SDA_3V SDA_3V CLK_NTSC_ENC
SDA_3V
RESETn CLK_PAL_ENC
RESETn
RESETn
Figure 9.7 Mini-Dock Connectors Schematic, Page 1

CLK_NTSC_ENC
SystemIo CLK_PAL_ENC VideoDecoder
DvEncoder
RESETn
CLK_14_318182
CLK_17_734475
PAL Frequency is 17.734475

NTSC Frequency is 14.318182
Signals are connected properly, with net names reversed.

75
76
4 3 2 1
5V
3.3V 3VDAVDD L1 L2
CLK_PAL_ENC CHROMA LUMA C93
CLK_ENCODER D
0.1UF
CLK_NTSC_ENC R15 2.7UH 2.7UH 16V
4
1
R14 47.5K C37 R40

C38 C41 D
47.5K 0.1UF R16 R39 100 80p Diffline CONN
VCC
ENA
16V 100 100 R44

SDA_3V 5 INA+
SDA_3V 18PF R20 18PF OUTA 7 32 P2-32
D INA-
SCL_3V C39 50V C40 100 C42 50V C43 D 6
SCL_3V 500 33 P2-33
159
158
154
153
6
5
3
4
1
2
129
132
137
7
135
134
D
P1-20 20 D 330PF 330PF 330PF 330PF D 37.4
500
P1-23 23 32 50V 50V 50V 50V 3 ENB
AB
AR
AG
TVCSYNC
INC
D D
PAL
VRT
VRB
DEC
P1-26 26 30 D D D D R43
INB+
ADEN
TVHSYNC
MENU
L3 10 OUTB
XOUT1
XOUT2
P1-29 29 31 INB-
8 30 P2-30
SELECT
TVVSYNC CVID 9
RGBOUT
CLKTYPE 152
XIN1/FIN1
XIN2/FIN2
P1-32 32 151 500 31 P2-31
R17 R18 R19 D TVCLK D 37.4
P1-35 35 146 37 AC 2.7UH 500
47.5K 47.5K 47.5K GHSDIV AC/BOUT 2 ENC
P1-38 38 145 39 AY C44 R41
D GHSOUT AY/GOUT D D
100 R42
P1-41 41 28 41 ACMP 12 INC+
GHSOUT2 ACMP/ROUT R21 18PF OUTC P2-19
INC-
14 19
P1-44 44 147 GVSOUT COMP 43 100 C45 50V C46 13
D 500 18 P2-18
37.4

P1-47 47 27 35 VREF 330PF 330PF
VEE
GVSOUT2 VREF 500

50V 50V D
P1-50 50 143 GCLK RSET 42 RSET C47
D D D
P1-53 53 141 0.1UF D D
11
GVSYNC 88 MD0 R22 R23 U15

P1-56 56 140 MD0 16V
GHSYNC MD1 150 1.00K RSET chosen to give 1V peak to peak analog MAX4019
87
46
47
48
49
50
38
40
39
41
42
43
81
82
83
84
85
86
88
89
90
D
P1-58 58 MD1 video outputs. D
1 100 107 86 MD2
P1-61 61 D TVCLK RA0 RED0 MD2 D D
MD3
XIN
2 99 106 85
SCL
PVS
SDA
PHS
TVHREF RA1 RED1 MD3
IREQ
SCLK
XOUT
D 3 98 105 83 MD4 MD[15..0] U9 U10
YUVIN
TEST1
TEST2
PCLKA
PCLKB
TVVS
GOUT1
GOUT2
GOUT3
RA2 RED2 MD4 MD0 1 44 MQ0 MD8 1 44 MQ8
PWRDN
MQ[15..0] DI0 DO0 DI0 DO0
PDSPEN
4 97 104 82 MD5
I2CADDR
TVHS RA3 RED3 MD5
HOSTCLK
MD1 2 43 MQ1 MD9 2 43 MQ9
P1-62 62 DV_CLK_OUT 9 95 103 81 MD6 DI1 DO1 DI1 DO1
GCLK RA4 RED4 MD6 MD2 3 42 MQ2 MD10 3 42 MQ10
P1-60 60 DV_ENABLE 8 94 102 80 MD7 DI2 DO2 DI2 DO2
GHREF RA5 RED5 MD7 MD3 4 41 MQ3 MD11 4 41 MQ11
P1-57 57 DV_VSYNC_OUT 6 93 101 55 MD8 DI3 DO3 DI3 DO3
GVS RA6 RED6 MD8 MD4 6 39 MQ4 MD12 6 39 MQ12
P1-59 59 DV_HSYNC_OUT 7 92 100 54 MD9 DI4 DO4 DI4 DO4
GHS RA7 RED7 MD9 MD5 7 38 MQ5 MD13 7 38 MQ13
110 53 MD10 DI5 DO5 DI5 DO5
P1-21 21 ROUT0 18 GA0 117 MD10 MD6 8 37 MQ6 MD14 8 37 MQ14
RIN0/YIN0 109 GREEN0 52 MD11 DI6 DO6 DI6 DO6
P1-22 22 ROUT1 17 GA1 116 MD11 MD7 9 36 MQ7 MD15 9 36 MQ15
RIN1/YIN1 108 GREEN1 50 MD12 3.3V DI7 DO7 DI7 DO7
P1-24 24 ROUT2 16 GA2 115 MD12
RIN2/YIN2 107 GREEN2 49 MD13
P1-25 25 ROUT3 15 GA3 114 MD13 10 15 10 15
RIN3/YIN3 105 GREEN3 48 MD14 WE IRDY WE IRDY
P1-27 27 ROUT4 14 GA4 112 MD14 11 11
RIN4/YIN4 104 GREEN4 U2A 47 MD15 IE IE
P1-28 28 ROUT5 13 GA5 111 MD15 13 30 13 30
RIN5/YIN5 103 GREEN5 AL128 98 MQ0 D WCK ORDY D WCK ORDY
P1-30 30 ROUT6 12 GA6 110 MQ0 14 14
RIN6/YIN6 102 GREEN6 97 MQ1 WRST 3.3V WRST 3.3V
GA7 109 MQ1 16 16
P1-31 31 ROUT7 11 120 GREEN7 96 MQ2 PLRTY PLRTY
RIN7/YIN7 BA0 MQ2 17 18 17 18
P1-33 33 GOUT0 27 119 127 95 MQ3 TST AVDD TST AVDD
GIN0/UVIN0 BA1 BLUE0 MQ3 5 5
P1-34 34 GOUT1 26 118 126 93 MQ4 VDD VDD
C GIN1/UVIN1 BA2 BLUE1 MQ4 RESETn 27 29 C50 RESETn27 29 C51 C
P1-36 36 GOUT2 25 117 125 92 MQ5 RESET VDD 0.1UF RESET VDD 0.1UF
GIN2/UVIN2 BA3 BLUE2 MQ5 35 40 16V 35 40 16V
P1-37 37 GOUT3 24 115 124 91 MQ6 RE VDD RE VDD
GIN3/UVIN3 BA4 BLUE3 MQ6 OEn 34 OEn 34
P1-39 39 GOUT4 23 114 122 90 MQ7 OE D OE
GIN4/UVIN4 BA5 BLUE4 MQ7 32 22 32 22 D
P1-40 40 GOUT5 22 113 121 65 MQ8 RCK AGND RCK AGND
GIN5/UVIN5 BA6 BLUE5 MQ8 31 12 31 12 3.3V
P1-42 42 GOUT6 21 U1A 112 120 64 MQ9 RRST GND 3.3V RRST GND
GIN6/UVIN6 BA7 BLUE6 MQ9 25 26 25 26
P1-43 43 GOUT7 20 AL300 119 63 MQ10 3.3V SDA GND SDA GND
GIN7/UVIN7 60 3.3V BLUE7 MQ10 24 33 3.3V 24 33
RB0 62 MQ11 SCL GND SCL GND
P1-45 45 BOUT0 36 59 MQ11 23 23 C49
BIN0 RB1 SDA_3V 10 60 MQ12 R34 SDAEN D
C48 SDAEN D 0.1UF
P1-46 46 BOUT1 35 58 SDA MQ12 10K 0.1UF 16V
BIN1 RB2 R24 SCL_3V 13 59 MQ13 16V
P1-48 48 BOUT2 34 57 SCL MQ13 D
NC4
NC3
NC2
NC1
NC4
NC3
NC2
NC1
BIN2 RB3

47.5K 11 58 MQ14 AL440B
P1-49 49 BOUT3 33 55 I2CADDR MQ14 D
BIN3 RB4 12 57 MQ15 D
28
21
20
19
28
21
20
19
P1-51 51 BOUT4 32 54 I2C MQ15 AL440B

BIN4 RB5 D
P1-52 52 BOUT5 31 53 77 MWENH
BIN5 RB6 157 INTYPE0 MWENH
P1-54 54 BOUT6 30 52 78 MWENL D
BIN6 RB7 156 INTYPE1 MWENL DV_VSYNC_OUT 26 P2-26
P1-55 55 BOUT7 29 70 71 MWRST
BIN7 GB0 MWRST DV_HSYNC_OUT 28 P2-28
69 D 66 MREN
GB1 149 RESET MREN 29 P2-29
68 69 MRRST
GB2 148 PWRDWN MRRST 3.3V
67 73 MWCLK D
140 GB3 MWCLK
ROMDATA0 65 68 MRCLK 27 P2-27
139 GB4 MRCLK
ROMDATA1 64
TEST1
TEST2
TEST3
TEST4
TEST5
TEST6
TEST7
TEST8
TEST9
TEST10
TEST11
TEST12
138 GB5 C52

ROMDATA2 63 0.1UF
9
137 GB6 RESETn

33
26
25
23
22
21
20
18
17
16
15
76 MEMCONFIG0
75 MEMCONFIG1
72 MEMTYP
ROMDATA3 62 16V
135 GB7 D
ROMDATA4 80
134 BB0 R25 L4
ROMDATA5 79
133 BB1 47.5K 3.3V ANALOG_R 20 P2-20
ROMDATA6 78
132 BB2 D 2.7UH 21 P2-21
ROMDATA7 77
B BB3 C53 B
D
BB4 75 D
RESETn 122 RESETB 74 R100
RESETn BB5 R26 18PF
126 OCLK BB6 73 75 C54 50V C55
72 330PF 330PF
IHSREF
OHSREF
OHSFB
OPLLCLK
ROMADDR0
ROMADDR1
ROMADDR2
ROMADDR3
ROMADDR4
ROMADDR5
ROMADDR6
ROMADDR7
ROMADDR8
ROMADDR9
ROMADDR10
ROMADDR11
ROMADDR12
ROMADDR13
ROMADDR14
ROMADDR15
100
129 VCOIN BB7
VCOIN1 50V 50V
D
123
124
125
127
142
143
144
145
147
148
149
150
152
153
154
155
157
158
159
160
D D
U11 L5
R27 PLLCLK ANALOG_G 22 P2-22
47.5K ROUT0 40 VAA 12 23 P2-23
R0 5VRGBDAC 5V 2.7UH
ROUT1 41 VAA 30 C56
R1 FB4 D
ROUT2 42 VAA 31
C57 R2
0.01UF C58 ROUT3 43 1 18PF
50V 0.1UF R3 GND 0805 R28
ROUT4 44 14 C61 C62 C63 C59 50V C60
16V R4 GND 0.1UF 0.1UF 0.1UF 75 330PF 330PF
D ROUT5 45 15 16V 16V 16V 50V 50V
D U2B R5 GND
8 14 ROUT6 46 27
VDD GND R6 GND D D D D D D
3.3V 24 19 ROUT7 47 28 L6
VDD GND R7 GND
46 29 38 ANALOG_B 24 P2-24
VDD GND GOUT0 2 GND
61 51 G0 39 2.7UH 25 P2-25
VDD GND GOUT1 3 GND
70 56 G1 48 C68
U1B C64 C65 C66 C67 VDD GND GOUT2 4 GND D R29
19 5 0.1UF 0.1UF 0.1UF 0.1UF 79 67 G2 75 D
VCC GND 16V 16V 16V 16V VDD GND GOUT3 5
3.3V 37 10 3.3V 89 74 G3 18PF
VCC GND D D D D VDD GND GOUT4 6 IOR
51 28 99 84 G4 IOR 33 C69 50V C70
VCC GND VDD GND GOUT5 7 IOG D 330PF 330PF
61 45 113 94 G5 IOG 32 50V 50V
VCC GND VDD GND GOUT6 8 IOB
66 56 123 108 G6 IOB 29
C71 C72 C73 C74 VCC GND C75 C76 C77 C78 VDD GND GOUT7 9 D D
0.1UF 0.1UF 0.1UF 0.1UF 91 71 0.01UF 0.01UF 0.01UF 0.01UF 139 118 G7 5VRGBDAC
16V 16V 16V 16V VCC GND 50V 50V 50V 50V VDD GND COMP 34
3.3V 96 76 144 142 BOUT0 16 C79 C80
D D D D VCC GND D D D D VDD GND B0
A 111 87 150 155 BOUT1 17 FS_ADJUST 36 0.1UF 0.1UF A
VCC GND VDD GND B1 16V 16V Video Encoder and RGB
116 101 160 BOUT2 18 R31
VCC GND 138 ADVDD GND B2 VREF 35 562 UNLESS OTHERWISE SPECIFIED,
C81 C82 C83 C84 121 106 BOUT3 19 DIMENSIONS ARE IN INCHES.
VCC GND B3 VREF TOLERANCES ARE:
131 ADVDD ADGND 128
0.01UF 0.01UF 0.01UF 0.01UF 141 131 BOUT4 20
50V 50V 50V 50V VCC GND 3.3V 3VDAVDD 130 ADVDD B4 U12 .XX=+/- <=+/-
151 136 ADGND 133 BOUT5 21 D
D D D D VCC GND FB5 B5 LT1790BCS6-1.25 .XXX=+/-
146 ADGND 136 R32 BOUT6 22
GND 34 DAVDD
49.9 B6 6 Vout Vin 4 THIS DOCUMENT CONTAINS
3.3V 156 BOUT7 23 C87 CONFIDENTIAL INFORMATION
GND 0805
44 DAVDD DAGND 36 R33 B7
FB6 C85 C86 45 DAVDD 4.7UF C88 WHICH IS PROPRIETARY TO SCHEMATIC DIAGRAM
0.1UF 0.1UF DAGND 38 DV_ENABLE 0.1UF SONOSITE, INC.
2 GND
1 GND
128 PLLVCC
PLLGND 130 C89 47.5K 10 BLANK 16V
16V 16V 16V NEITHER THE DOCUMENT NOR
AL128 DAGND 40 18PF THE INFORMATION CONTAINED
C2 DOCK
AL300 D D
11 SYNC
0805 C90 50V DV_CLK_OUT THEREIN SHALL BE DISCLOSED SIZE REV
D 26 CLOCK D
0.1UF D D D OR REPRODUCED, IN WHOLE OR
16V D D PART, WITHOUT THE EXPRESS B D02457 A
ADV7120KST30 WRITTEN CONSENT OF
D SONOSITE, INC. SCALE NONE DATE Friday, December 20, 2002 SH. 2 OF 4
4 3 2 1
4 3 2 1
63 P1-63
66 P1-66
69 P1-69
72 P1-72
75 P1-75
78 P1-78
81 P1-81
84 P1-84
87 P1-87
90 P1-90
SDA_3V
SDA_3V 93 P1-93
SCL_3V 200 PIN
SCL_3V R5 R6 R7 D 96 P1-96
D 47.5K 47.5K 47.5K 99 P1-99 DOCK CONN D
3.3V 101 P1-101
104 P1-104
R8 D
47.5K
DV_VSYNC_IN 100 P1-100
DV_HSYNC_IN 102 P1-102
D
D DV_ENABLE_IN 103 P1-103
DV_CLK_IN 105 P1-105
46
47
48
49
50
38
40
39
41
42
43
81
82
83
84
85
86
88
89
90
1 100 RIN0 64 P1-64
TVCLK RA0
RIN1
XIN
2 99 65 P1-65
SCL
PVS
SDA
PHS
TVHREF RA1
IREQ
SCLK
XOUT
3 98 RIN2 67 P1-67
YUVIN
TEST1
TEST2
PCLKA
PCLKB
TVVS
GOUT1
GOUT2
GOUT3
RA2
PWRDN
PDSPEN
4 97 RIN3 68 P1-68
I2CADDR
TVHS RA3
HOSTCLK
TV_CLK 9 95 RIN4 70 P1-70
GCLK RA4
80 PIN CONN TO TV_HREF 8 94 RIN5 71 P1-71
GHREF RA5
CONNECTOR PCB TV_VSYNC 6 93 RIN6 73 P1-73
GVS RA6
TV_HSYNC 7 92 RIN7 74 P1-74
P2-34 34 LUMA_IN GHS RA7
C13 U5A 110 GIN0 76 P1-76
P2-36 36 CHROMA_IN 84 45 Y0 18 GA0
AY0 Y0 RIN0/YIN0 109 GIN1 77 P1-77
P2-35 35 0.1UF 86 46 Y1 17 GA1
AY1 Y1 RIN1/YIN1 108 GIN2 79 P1-79
16V 88 47 Y2 16 GA2
R9 R10 C14 AY2 Y2 RIN2/YIN2 107 GIN3 80 P1-80
D 75 75 90 48 Y3 15 GA3
AC0 Y3 RIN3/YIN3 105 GIN4 82 P1-82
0.1UF 92 53 Y4 14 GA4
AC1 Y4 RIN4/YIN4 104 GIN5 83 P1-83
D D 16V 94 54 Y5 13 GA5
AC2 Y5 RIN5/YIN5 103 GIN6 85 P1-85
CLK_26_8Mhz 8 55 Y6 12 GA6
XTALI Y6 RIN6/YIN6 102 GIN7 86 P1-86
7 56 Y7 GA7
C XTALO Y7 11 120 BIN0 88 P1-88 C
RESETn 10 RIN7/YIN7 BA0
RESETn RST UV0 27 119 BIN1 89 P1-89
C0 33 GIN0/UVIN0 BA1
3.3V UV1 26 118 BIN2 91 P1-91
PAL_NTSCn 58 C1 34 GIN1/UVIN1 BA2
U14 PORTA UV2 25 117 BIN3 92 P1-92
3 XTALIN VDD 7 24 C2 35 GIN2/UVIN2 BA3
CLK_ENCODER SCH(PORTB) UV3 24 115 BIN4 94 P1-94
4 XTALOUT 57 C3 36 GIN3/UVIN3 BA4
6 TESTEN UV4 23 114 BIN5 95 P1-95
CLKA D 96 C4 37 GIN4/UVIN4 BA5
8 FS 5 C91 TEST UV5 22 113 BIN6 97 P1-97
CLKB 0.01UF C5 38 GIN5/UVIN5 BA6
2 GND CLKC 1 50V UV6 21 U4A 112 BIN7 98 P1-98
77 C6 39 GIN6/UVIN6 BA7
C15 VRT UV7 20
CY22381FI 0.1UF 78 C7 44 GIN7/UVIN7 AL300 60
D C16
D 16V VRB RB0

0.1UF C17 97 36 59
D 16V COMP2 EXV0 16 BIN0 RB1
0.1UF 35 58
D 16V EXV1 27 BIN1 RB2
75 SCLK EXV2 28 34 BIN2 RB3 57
D
SCL_3V 72 33 55
SDAT EXV3 61 BIN3 RB4
SDA_3V 69 32 54
AEX0 EXV4 62 BIN4 RB5
70 AEX1 EXV5 63 31 BIN5 RB6 53
CLK_NTSC_ENC
EXV6 68 30 BIN6 RB7 52
CLK_PAL_ENC
D
EXV7 71 29 BIN7 GB0 70
GB1 69
TV_HSYNC 26 25
HS1 HAV 68
76 5 GB2
HS2(IIC) EHAV 67
3 22 140 GB3
VAV(OENC0)ODD ROMDATA0 65
4 17 139 GB4
R11 EVAV(OENC1)PID ROMDATA1 64
10K 15 73 138 GB5
OEN CCDAT ROMDATA2 63
TV_VSYNC 23 74 137 GB6
VS CCEN ROMDATA3 62
D R12 18 21 135 GB7
10K CK CK2 ROMDATA4 80
134 BB0
B KS0127B ROMDATA5 79 B
133 BB1
D ROMDATA6 78
D 132 BB2
ROMDATA7 77
BB3
BB4 75
3.3V RESETn 122 RESETB 74
BB5
126 OCLK BB6 73
U5B
6 72
ROMADDR0
ROMADDR1
ROMADDR2
ROMADDR3
ROMADDR4
ROMADDR5
ROMADDR6
ROMADDR7
ROMADDR8
ROMADDR9
ROMADDR10
ROMADDR11
ROMADDR12
ROMADDR13
ROMADDR14
ROMADDR15
20 VDD VSS 129 VCOIN BB7

C18 C19 59 VDD 13 VCOIN2
VSS
0.1UF 0.1UF 14
123 IHSREF
124 OHSREF
125 OHSFB
127 OPLLCLK
142
143
144
145
147
148
149
150
152
153
154
155
157
158
159
160
16V 16V VSS

11 VDD3 VSS 19
3.3V D D R13
12 VDD3 VSS 40 47.5K
42 VDD3 VSS 41
43 VDD3 VSS 60
C20 C21 C22 66 64 C23
0.01UF 0.01UF 0.01UF VDD3 VSS 0.01UF C24
50V 50V 50V 67 65 50V 0.1UF
VDD3 VSS 16V
D D D
VSS 83
5V D
85 VDDA VSS 87 D
FB1 89 91
VDDA VSS
93 VDDA VSS 95
C25 C26 U4B
0805 98 VDDA 19 VCC GND 5
0.1UF 0.1UF 1
16V 16V NCP 3.3V 37 10
2 VCC GND
5V D D 9 VDDA1 NCP 51 28
29 VCC GND
NCP 61 45
FB2 30 VCC GND
NCP 66 56
31 C27 C28 C29 C30 VCC GND
NCP 0.1UF 0.1UF 0.1UF 0.1UF 91 71
C31 32 VCC GND
0805 0.1UF NCP 16V 16V 16V 16V 96 76
49 3.3V VCC GND Video Decoder
A 16V D D D D A
NCP 111 87
D 50 VCC GND
NCP 116 101
51 VCC GND UNLESS OTHERWISE SPECIFIED,
NCP 121 106 DIMENSIONS ARE IN INCHES.
52 C32 C33 C34 C35 VCC GND
NCP 0.01UF 0.01UF 0.01UF 0.01UF 141 131 TOLERANCES ARE:
79 50V 50V 50V 50V VCC GND .XX=+/- <=+/-
NCP 151 136
80 D D D D VCC GND .XXX=+/-
NCP 146
81 GND THIS DOCUMENT CONTAINS
NCP 3.3V 156
82 GND CONFIDENTIAL INFORMATION
NCP FB3 WHICH IS PROPRIETARY TO SCHEMATIC DIAGRAM
99 SONOSITE, INC.
NCP 128 PLLVCC
PLLGND 130 NEITHER THE DOCUMENT NOR
NCP 100 AL300 THE INFORMATION CONTAINED
C2 DOCK
0805 C36 THEREIN SHALL BE DISCLOSED SIZE REV
KS0127B D 0.1UF D OR REPRODUCED, IN WHOLE OR
16V PART, WITHOUT THE EXPRESS B D02457 A
WRITTEN CONSENT OF
4 3 2 1

77
78
4 3 2 1
80 PIN DIFF LINE CONN

200 PIN DOCK CONN
P1-1 1 VPWR_IN 65 P2-65

P1-2 2 66 P2-66
P1-3 3 67 P2-67
P2-68 200 PIN DOCK CONN
P1-4 4 68
P1-5 5 69 P2-69 P1-169 169 DOCK_TRSTN
P1-6 6 VPWR_IN_RTN 70 P2-70 Dock Power Soft Start Switch P1-170 170 DOCK_TMS SYSTEM JTAG INTERFACE:
P1-7 7 71 P2-71 P1-171 171 DOCK_TDI Allow for System JTAG
D D
DC Power / P1-8 8 72 P2-72 P1-172 172 DOCK_TCK chain to be accessed.
P1-9 9 73 P2-73 P1-173 173 DOCK_TDO
Battery Charger VPWR
P1-10 10 74 P2-74

Interface
P1-11 11 VCHGR 75 P2-75
P1-12 12 76 P2-76 P1-168 168
7
8
5
6
P1-13 13 77 P2-77 P1-175 175
D1 D2 D1 D2
P1-14 14 78 P2-78 P1-176 176
R35 Q1A Q1B
P1-15 15 VBAT_SNS 79 P2-79 33.2K P1-177 177
2 G SI4920DY 4 G SI4920DY
P1-16 16 P1-179 179 MII Interface:
P1-17 17 RATE 80 P2-80 S S P1-180 180
3.3V
1
3
P1-18 18 DOCK_SENSEA P1-181 181 Allow Ethernet Physical Layer to exist in
PRINTER_SENSE 63 P2-63 C92
P1-19 19 DOCK_SENSEB U6 R36 P1-182 182 Dock if necessary.
64 P2-64 RESETn 100K 4.7UF
3 MR RESET 1 RESETn 16V P1-183 183
3.3V 3.3V 4 WDI 3.3V 5V P1-185 185
ON_OFF D
P1-144 144 D VDD 5 D
GND 2 D P1-187 187
P1-145 145 DOCK_SENSE0 C1
TPS3820-33DB P1-189 189
P1-146 146 DOCK_SENSE1 R1 R2 0.1UF C4 C5
47.5K 47.5K 16V P1-191 191
P1-147 147 DOCK_SENSE2 330UF 330UF
3
D
D R37 Q2 10V 10V P1-192 192
P1-148 148 SYSTEM_SENSE0 1
System 2N3904 P1-193 193
P1-149 149 SYSTEM_SENSE1 D D
2
10K P1-194 194
Sense / P1-150 150 SYSTEM_SENSE_ENA
R38 P1-195 195
Status P1-151 151 SYSTEM_STATUS0 100K D
P1-197 197
P1-152 152 SYSTEM_STATUS1 5VIN
P1-198 198
P1-153 153 SYSTEM_STATUS2 3_3VIN
D1 D P1-199 199
P1-154 154
P1-155 155 C2 MBR0540T1
C 0.1UF P1-174 174 C
P1-156 156 16V U7
C3 P1-178 178
P1-157 157 0.1UF 6 VCC R3
D D 16V VL 1 10K P1-184 184
P1-158 158 5 SHDN GND 2
D P1-186 186
SDA_3V
4 IOC IOL 3 SDA_3V P1-188 188
D
D P1-190 190
P1-159 159 1 P2-1 MAX3371
D P1-196 196
P1-160 160 SDA_5V 2 P2-2
P1-200 200
P1-161 161 SCL_5V 3 P2-3
U8
P1-106 106 4 P2-4 5VIN 6 R4
VCC VL 1 10K
P1-107 107 EXT_RXC 5 P2-5 5 SHDN GND 2 P1-201 MTG1
P1-108 108 EXT_TXC 6 P2-6 SCL_3V
4 IOC IOL 3 SCL_3V

P1-202 MTG2
P1-109 109 EXT_RTSC 7 P2-7
P1-110 110 EXT_CTSC 8 P2-8 MAX3371
ECG / Honda C6 3.3V D
P1-132 132 9 P2-9 0.1UF U13
Connector C7 16V
P1-133 133 ECG_ANALOG 10 P2-10 1 NC
Interface 0.1UF VCC 8
P1-134 134 ECG_FILTER_CLK 11 P2-11 16V 2 E1
D
P1-135 135 ECG_POWER_CLK 12 P2-12 D 3 E2 SCL 6
P1-136 136 ECG_SENSE 13 P2-13
SDA 5
P1-137 137 14 P2-14
P1-140 140 AUD_R_OUT 15 P2-15 7 WC# VSS 4
P1-141 141 AUD_L_OUT 16 P2-16 3_3VIN
M24C04-WDW6T
D D
P1-167 167 VPWR
D
VPWR
D
B B
P1-138 138 AUD_R_IN 37 P2-37
P1-139 139 AUD_L_IN 38 P2-38
P1-142 142 HEADPHONE_SNS 17 P2-17

P1-143 143
Audio I/O
P1-162 162
P1-163 163 MONO_OUT 40 P2-40
80 PIN DIFF LINE CONN
P1-164 164 U3
P1-165 165 MONO_IN 39 P2-39 13 T1IN
P1-166 166 12 VCR_RX 42 P2-42
T2IN 17
15 T1OUT VCR_TX 43 P2-43
R1OUT 8
P1-111 111 41 P2-41 10 T2OUT VCR_RTS 44 P2-44
R2OUT
VCR SERIAL P1-112 112 VCR_RXC 2 16 VCR_CTS 45 P2-45
C1+ R1IN
PORT CMOS P1-113 113 VCR_TXC C8 4 9
C1- R2IN
P1-114 114 VCR_RTSC 0.1UF C9 5
16V 0.1UF C2+ 11
P1-115 115 VCR_CTSC 16V 6 INVALID
C2- 1
3 RDY
P1-116 116 56 P2-56 V+
7 V-
P1-117 117 USB_D+ 57 P2-57
USB P1-118 118 USB_POWER 58 P2-58 C10 C11 14 FORCEON
SIGNALS P1-119 119 USB_D- 59 P2-59 0.1UF 0.1UF 20 FORCEOFF
16V 16V
P1-120 120 46 P2-46 D D 19 VCC
P1-121 121 ENET_RX+ 47 P2-47 RESETn GND
P1-122 122 ENET_TX+ 48 P2-48 3_3VIN MAX3225E 18
P1-123 123 ENET_RX- 49 P2-49
Ethernet P1-124 124 ENET_TX- 50 P2-50 D
System I/O
A A
P1-125 125 51 P2-51
P1-126 126 ACTLED 53 P2-53 C12 UNLESS OTHERWISE SPECIFIED,
0.1UF DIMENSIONS ARE IN INCHES.
P1-127 127 LILED 54 P2-54 16V TOLERANCES ARE:
P1-128 128 SPEEDLED 55 P2-55 .XX=+/- <=+/-
D
3.3V ENET_LED_PWR 52 P2-52 .XXX=+/-
Printer THIS DOCUMENT CONTAINS

P1-129 129 60 P2-60 CONFIDENTIAL INFORMATION
Control / P1-130 130 STAT_FRAME 61 P2-61 WHICH IS PROPRIETARY TO SCHEMATIC DIAGRAM
SONOSITE, INC.
API Test P1-131 131 CTRL_LINE 62 P2-62 NEITHER THE DOCUMENT NOR
THE INFORMATION CONTAINED
C2 DOCK
MTG1 P2-81 THEREIN SHALL BE DISCLOSED SIZE REV
D
OR REPRODUCED, IN WHOLE OR
MTG2 P2-82 PART, WITHOUT THE EXPRESS B D02457 A
WRITTEN CONSENT OF
4 3 2 1
4 3 2 1
80 Pin Diff-Line Connector R23 MTG4 P5-18

P10-1 1
0.00 MTG3 P5-17 80 Pin Diff-Line Connector
P10-4 4
Place near P5 MTG2 P5-16 0805
MTG1 P5-15 FB1 600 OHM@100MHZ
D P10-34 34 LUMA_IN Y_IN
4
3
P11
P10-2 2 ECG_SDA 10 P5-10 C1 C2 L1 C3 S-Video DIN - Front
P10-3 3 ECG_SCL 11 P5-11 100PF 100PF 100PF
50V 50V 4 CHROMA LUMA 3
P10-5 5 EXT_RXC 8 P5-8 P10-35 35 YCIN_RTN 50V YIN_RTN
1
2
P10-6 6 EXT_TXC 6 P5-6
P10-7 7 EXT_RTSC 7 P5-7 0805
P10-8 8 EXT_CTSC 9 P5-9 Honda Connector: ECG / FB2 600 OHM@100MHZ
Serial Debug / Audio P10-36 36 CHROMA_IN C_IN
D P10-9 9 VPWR 1 P5-1 D
4
3
R1 2 RTN RTN 1
P10-10 10 ECG_ANALOG 3 P5-3 C4 C5 L2 C6
P10-11 11 EGC_FILTER_CLK 4 P5-4 100PF 100PF 100PF
P10-12 12 ECG_PWR_CLK 5 P5-5 0.00 50V 50V 50V CIN_RTN
D
1
2
5
6
7
P10-13 13 ECG_SENSE 2 P5-2 R24

P10-14 14 ECG_AUDIO_RIGHT 12 P5-12 AUD_R_OUT R2 R25
ECG_AUDIO_LEFT 13 P5-13 0.00
D 1.00K R3 0.00
AUD_L_OUT
14 P5-14
1.00K
C7 C8 C9 C10
0.001UF 0.001UF 0.001UF 0.001UF
50V 50V 50V 50V 1 P7-1
3.3V 9 P7-9
R4 R5 R6
1.00K 1.00K P10-37 37 AUD_R_IN 6 P7-6
R8 R7 4 P7-4
P10-38 38 AUD_L_IN 1.00K R9
100K
1.00K P10-39 39 MONO_IN 5 P7-5
R10 1.00K C11 C12
R11 H_AUDIO_L 2 P4 P10-40 40 0.001UF 0.001UF GND1 P7-10
MONO_OUT OEM Serial
P10-15 15 AUD_R_OUT H_AUDIO_SNS 11 P10-41 41 0.00 50V 50V GND2 P7-11
10K D Port
P10-16 16 AUD_L_OUT H_AUDIO_R 3 Headphone Audio Output P10-42 42 VCR_RX 0805 FB3 2 P7-2
R12
P10-17 17 HEADPHONE_SNS 1 P10-43 43 VCR_TX 0805 FB4 3 P7-3
1.00K P10-44 44 VCR_RTS 0805 FB5 7 P7-7
3 POS PHONE P10-45 45 VCR_CTS 0805 FB6 8 P7-8
C13 C14 C15
0.1UF 0.001UF 0.001UF C16 P10-46 46
0.001UF
Figure 9.11 Dock Connectors Schematic

16V 50V 50V C17 C18 C19 C20
50V 47PF 47PF 47PF 47PF
D
D 50V 50V 50V 50V
P10-48 48 ENET_TX+
C P10-50 50 ENET_TX- C
GND2
GND1
0805 P10-47 47 ENET_RX+ Differential 100 ohm lines critical routing

FB7 600 OHM@100MHZ 1
P10-49 49 ENET_RX-
P10-19 19 CVID CVID_OUT P3 2
4
3
P10-18 18 CVID_RTN 2 P10-51 51 3
C21 C22 L3 C23 Composite Video Ethernet
Output P10-52 52 ENET_LED_PWR TDC 4
100PF 100PF 100PF 1 D1 D2
50V 50V 50V P10-53 53 RDC 5 with
R13
1
2
0.00 PHONO P10-54 54 GREEN GREEN 6 Transformer
R26 P10-55 55 SPEED LED ACTLED 8
P10-56 56 LILED C45 8 POS RJ45
D 18PF C46
0.00 0.1UF P2
50V C47
0805 D 16V
600 OHM@100MHZ D 0.001UF
FB8 600 OHM@100MHZ 50V
4
3
D
P10-20 20 ANALOG_R R_OUT 1 P1-1 D
Differential 100 ohm lines critical routing
4
3
L4
C24 C25 L5 C26 P10-57 57 USB_D+ 3 P8-3
100PF 100PF 100PF P10-59 59 USB_D- 2 P8-2
1
2
P10-21 21 RGB_RTN 50V 50V 50V 6 P1-6 P10-58 58 USB_VBUS 1 P8-1
1
2
R27 P10-60 60 4 P8-4
0805 USB Connector
3.3V GND1 P8-5
FB9 600 OHM@100MHZ 0.00 R14
D
P10-22 22 ANALOG_G G_OUT 2 P1-2 GND2 P8-6
4
3
499K
C27 C28 L6 C29
100PF 100PF 100PF 15 POS VGA R15
P10-23 23 50V 50V 50V 7 P1-7 Connector P10-61 61 STAT_FRAME
1
2
1.00K R16
R28 P10-62 62 CTRL_LINE 2 P12
0805
P10-63 63 PRINTER_SENSE R17 1.00K 11
FB10 600 OHM@100MHZ 0.00 Printer Control / API
P10-24 24 ANALOG_B B_OUT 3 P1-3 P10-64 64 10K 3
4
3
B R18 1 B
D
C30
C31 C32 L7 C33 0.1UF 47.5K
100PF 100PF 100PF C34 C35
16V 100PF 100PF 3 POS PHONE
P10-25 25 50V 50V 50V 8 P1-8
1
2
50V 50V
R19 D D
R29 4 P1-4 P10-65 65
5 P1-5 Not Used P10-66 66
0.00 R20 0.00 P10-67 67
D
P10-26 26 VSYNC 14 P1-14
P10-68 68
12 P1-12
R21 49.9 P10-69 69 VPWR_IN
P10-28 28 HSYNC 13 P1-13
P10-70 70 VPWR_IN_RTN
P10-29 29 49.9 Not Used
C36 C37 15 P1-15 P10-71 71 1 P9-1
D 100PF 100PF 9 P1-9 Key Pin P10-72 72 2 P9-2 Power Input
50V 50V 10 P1-10 P10-73 73 3 P9-3 Connector
3.3V
11 P1-11 P10-74 74 4 P9-4
P10-27 27
GND1 P1-16 Mounting P10-75 75 VCHGR 5 P9-5
GND2 P1-17 Holes P10-76 76 GND1 P9-6
C38
0.1UF P10-77 77 GND2 P9-7
16V P10-78 78
D P10-79 79 VBAT_SNS
P10-80 80 RATE
0805
FB11 600 OHM@100MHZ P10-82 MTG2
P10-30 30 LUMA_OUT Y_OUT P10-81 MTG1 D Place near P9
4
3
P6
R30
C39 C40 L8 C41 S-Video DIN - Front
100PF 100PF 100PF 0.00
50V 50V 50V 4 CHROMA LUMA 3 D
P10-31 31 YCOUT_RTN Y_RTN
1
2
A A
0805
FB12 600 OHM@100MHZ
UNLESS OTHERWISE SPECIFIED,
P10-32 32 CHROMA_OUT C_OUT DIMENSIONS ARE IN INCHES.
4
3
2 RTN TOLERANCES ARE:
L9
RTN 1 .XX=+/- <=+/-
C42 C43 C44
100PF 100PF 100PF .XXX=+/-
P10-33 33 50V 50V 50V C_RTN
1
2
5
6
7
THIS DOCUMENT CONTAINS

CONFIDENTIAL INFORMATION
R31 WHICH IS PROPRIETARY TO SCHEMATIC DIAGRAM
R22 R32 SONOSITE, INC.
0.00 NEITHER THE DOCUMENT NOR
0.00 THE INFORMATION CONTAINED C2 Dock Connector
0.00 THEREIN SHALL BE DISCLOSED SIZE REV
OR REPRODUCED, IN WHOLE OR
D PART, WITHOUT THE EXPRESS B D01911 C
WRITTEN CONSENT OF
SONOSITE, INC. SCALE NONE DATE Friday, May 10, 2002 SH. 1 OF 1
4 3 2 1

79
9.5 Theory of Operation
9.5.1 Video
The video data originates on the main PCBA in 640 × 480, RGB-888 square pixel format at 60Hz refresh rate NTSC
and 50Hz for PAL video.
9.5.1.1 VGA Video Output

The digital RGB data is converted to progressive scan analog RGB on the dock PCB. The analog RGB drives a
VGA style connector and is also the input for the video encoder.
9.5.1.2 Analog Interlaced Video Outputs

The digital RGB data is converted to analog interlaced composite and S-Video outputs on the dock PCB. A video
processor converts RGB and output in the selected video format.
For NTSC video mode, the processor is converting from progressive scan to interlaced and is responsible for the
color space conversion converting from RGB to composite and S-Video.
For PAL video mode, the processor is doing the interlacing and color space conversion and outputs 768 × 576
lines at 50Hz.
9.5.1.3 Video Decoders

A video decoder digitizes the input S-Video data. A separate component performs the de-interlace and converts
to digital RGB data.
9.5.2 Power Distribution

The battery charger and VPWR signals provided by the AC power supply are intended to be passed through the
dock so that the system behaves the same whether the AC power supply is plugged into the dock or directly to
the system (with no dock).
The dock uses the 3.3V and 5V power supplies available on the Main PCB. When the dock is connected, the dock
provides necessary surge limiting and reset circuitry necessary to ensure proper operation of all components.
The dock provides the capability to turn OFF 3.3V and 5V power supplies to as much of the dock as possible to
allow for a minimum power state.

9.6 Replacement Procedures
Replacement procedures for all replaceable parts are not discussed in this manual. Replacement of many
mechanical parts is intuitive to properly trained service personnel and due to the simple nature of these kinds of
repairs procedures are determined to be not necessary.

• 1/8 inch, 5/32 inch, and 1/4 inch hex wrench, ball type
• 3/8 inch and 1/2 inch wrench or socket
• 13/16 inch and 3/4 inch open end wrench
9.6.2 Cup Surround

1 Remove the six (6) screws attaching the cup surround to the top of the docking system.
3/8" Hex nuts (2)
1/8" Allen screws (3)

1/8" Allen screws (3)
Figure 9.12 Cup Surround Screws
2 Lift the cup surround from the docking system.
9.6.3 Casters
1 Tilt the docking system in any direction and lay it on its side.
2 Remove the caster by turning the 13/16 inch nut on the caster shaft counter-clockwise until the caster is
removed from the docking system base.
3 Install the new caster in the same manner.

9.6.4 Power Supply
1 Remove the rear cover on the docking system by pressing on the black lever at the bottom of the cover per
Figure 9.13.
Rear cover
release lever
Figure 9.13 Mobile Docking System Rear Cover
2 Pull the cover down and away from the docking system.
3 The power supply is located on the upper shelf on the left side.
Power supply
Power strip
Printer/video
cables
Figure 9.14 Mobile Docking System Power Supply
4 Unplug the power connector from the power strip and from the power supply per Figure 9.14.
5 Remove cable cover from top rear of docking system to expose mini-dock wiring.

6 Remove the power supply from the docking system by unplugging the cable from the mini-dock per
Figure 9.15 and removing the cable tie that attaches it to the docking system.
Power supply
cable
Cable tie
Figure 9.15 Mini-Dock Connectors
7 The power supply cable is threaded through the TITAN support leg from the power supply in the rear up to
the mini-dock.
8 Lower the docking system to the lowest point.
9 Tilt the docking system toward the rear and carefully lower it so it lays on the ground.
10 In the right support leg, as you face it from the bottom, you will notice the cables attached to a cable tie.
Remove the cable tie and the tape from around the cables.
11 Separate the cables and pull the cable from the power supply down to the bottom of the docking system
support leg.
12 Tilt the docking system back to the upright position and pull the power supply from the rear of the docking
system, pulling the cable up from the support leg.
13 Install the new power supply into the rear of the docking system and thread the cable down the support leg.
14 Lay the docking system back down, pull the excess cable free then thread the cable up the support leg to the
top of the docking system.
15 Attach the power supply connector to the mini-dock and replace the cable tie.
16 Retape the wires and reattach the wires to the support leg with a new cable tie.
17 Install the power supply power cord.

9.6.5 Locking Handle
1 Remove the six (6) screws attaching the cup surround to the top of the docking system per Figure 9.12.
3 Remove the two 3/8 inch locking nuts from the handle screws per Figure 9.12.
4 Remove the two 1/8 inch hex screws holding the handle in place per Figure 9.16.
Deflector
Retaining clip
1/8" hex screw
Video/power
cables
Figure 9.16 Handle Screws
5 Lift the handle from the docking system. Remove the retaining clip from the latch link assembly and remove
the handle.
6 Install the new handle and reassemble the docking system in the reverse order.
9.6.6 Deflector
1 Remove the six (6) screws attaching the cup surround to the top of the docking system per Figure 9.12.
3 Peel the old deflector from the frame per Figure 9.16.
4 Clean any adhesive residue from the frame.
5 Install the new deflector in place of the old deflector noting the notches cut out for the attaching hardware.
6 Reinstall the cup surround.
9.6.7 Mini-Dock
1 Remove the cover from the top of the docking system just behind the mini-dock per Figure 9.17 to expose the
cables attached to the mini-dock.
2 Disconnect all of the cables.
Cable cover
Figure 9.17 Mobile Docking System Cable Cover

3 Raise the docking system to the highest point by pressing on the foot pedal and lifting on the outer edges of
the cup surround.
4 Looking under the top of the docking system note two access holes per Figure 9.18. These access holes are to
remove the two (2) screws holding the mini-dock in place.
Access holes
Figure 9.18 Mini-Dock Access Holes
5 Looking from the front of the docking system find the two screws holding the mini-dock in place and remove
them using a Phillips screwdriver.
Phillips screw
Access hole
Figure 9.19 Mini-Dock Screws
6 Lift the mini-dock from the docking system.

7 Reinstall the mini-dock by following these steps in reverse order.

9.6.8 Triple Transducer Connect
The Triple Transducer Connect module is held in place with four screws accessible from beneath the Cup
Surround. To remove the Triple Transducer Connect for repair or replacement follow the steps below.
To remove the Triple Transducer Connect:

1 Remove the cup surround per Section 9.6.2.
2 Set the cup surround to the side.
3 Locate the four (4) screws attaching the Triple Transducer Connect to the Mobile Docking System as in
Figure 9.20.
5/32" hex
screws (4)
Figure 9.20 Triple Transducer Attachment Screws
4 Remove the screws using the 5/32” hex wrench. Remove the screws carefully as the Triple Transducer
Connect will drop from the bottom of the Mobile Docking System.

To disassemble the Triple Transducer Connect:
1 Remove the five (5) #1 Phillips screws securing the bottom enclosure to the Triple Transducer Connect per
Figure 9.21.
#1 Phillips
screws (5)
Figure 9.21 Triple Transducer Enclosure Screws
2 Remove the bottom enclosure and set to the side.
To remove the Main PCBA Assembly:

1 Remove the four (4) 1/8" hex screws and the four (4) nest frame shoulder screws from each nest frame
assembly, see Figure 9.22.
1/8" hex
screws (3)
Strain relief
1/8" hex
screws (4)
5/16" shoulder
screws (4) in
each nest frame
assembly
Figure 9.22 Main PCBA screws and Nest Frame Shoulder Screws

2 Remove each nest frame assembly by tilting the board on edge and lifting off each nest frame.
Note: Tilting the board prevents the interposer connectors from dropping out of each nest frame assembly.
See Figure 9.23.
Figure 9.23 Nest Frame Removal
3 After lifting off each nest frame assembly set the Triple Transducer Connect back on the top enclosure.
4 Tilt the Main PCBA over per Figure 9.24.
Transducer cable
connectors (2)
Figure 9.24 Transducer Connector
5 At this point the transducer can be disconnected from the Main PCBA and the Main PCBA removed from
the Triple Transducer Connect. Remove the transducer cable connectors shown in Figure 9.24.
6 The transducer assembly is removed from the Triple Transducer Connect by removing the strain relief
shown in Figure 9.22. Remove the three (3) 1/8" hex screws from the strain relief.

Appendix A: Parts List
This section contains a list of field-replaceable parts.
A.1 Replacement Parts List

The following tables contain all the replaceable parts for the TITAN Ultrasound System. All quantities are one
unless otherwise noted.
A.1.1 Display
Table A.1: Display
Part Number Description
P03861 Service Assembly Display TITAN
Appendix A: Parts List 89

A.1.2 Control Panel
Table A.2: Control Panel
P03862 Service Assembly Control Panel, TITAN, English
P03863 Service Assembly Control Panel, TITAN, English, International
P03864 Service Assembly Control Panel, TITAN, French
P03865 Service Assembly Control Panel, TITAN, German
P03866 Service Assembly Control Panel, TITAN, Italian
P03867 Service Assembly Control Panel, TITAN, Spanish
P03868 Service Assembly Control Panel, TITAN, Portuguese
90 Appendix A: Parts List

A.1.3 Replacement Parts, System
1
3
2 2
Table A.3: System
Find Number Part Number Description
1 P03870 Service Assembly Power Supply, TITAN
2 P03872 Service Assembly Speaker, TITAN
3 P03869 Service Assembly TGC, TITAN
4 P03873 Service Assembly Upper Enclosure, TITAN
not shown P03874 Service Assembly Lower Enclosure, TITAN

Note: This part requires printing a replacement label for the product.
Contact SonoSite Technical Support when ordering this part to have the
label printed and placed on the part.
5 P03871 Service Assembly Main PCBA, TITAN

Note: This part does not include the transducer nest frame assembly. Those
parts must be ordered separately if needed to complete the replacement of
the Main PCBA.

Figure A.1 Power Supply, P03870
Figure A.2 Speaker Assembly, P03872

Figure A.3 TGC Assembly, P03869
Figure A.4 Upper Enclosure, P03873

Figure A.5 Lower Enclosure Assembly, P03874 (top view)
Figure A.6 Lower Enclosure, P03874 (bottom view)

Figure A.7 Main PCB Assembly, P03871

A.1.4 Transducer Nest Frame Assembly
3
1 (x8)
5 8 (x4)
2 (x4)
4 (x4)
6 (x2)
7 (x2)
Figure A.8 Nest Frame Parts
Table A.4: Nest Frame Assembly
Find Number Part Number Description
1 P00364 Connector, Interposer
2 P00524 Screw, Shoulder, Thrust Plate
3 P00353 Wear Plate
4 P00646 Spring, Thrust Plate, .047 wire
5 P02860 Nest Plate, Interposer, TITAN
6 P03834 Shield, Perimeter, Long
7 P03833 Shield, Perimeter, Short
8 P02861 Post, Mounting, TITAN

A.1.5 AC Adapter
Figure A.9 Power Supply/Battery Charger, P01139
Table A.5: AC Adapter
P01139 Power Supply/Battery Charger

A.1.6 Mini-Dock
Figure A.10 Mini-Dock Assembly, P03875
Figure A.11 Mini-Dock Rear Connector, P03875
Table A.6: Mini-Dock
P03875 Service Assembly Mini-Dock, TITAN

A.1.7 Mobile Docking System
12
18
19
8
13
9
10
11
15
14
6
Figure A.12 Mobile Docking System Front View

7
5 2
16
17
Figure A.13 Mobile Docking System Rear View
Table A.7: Replaceable Parts List
Find Number Part Number Part Description
P00536 Cable, RCA/BNC Video (not shown)
P00537 Cable, Printer Control (not shown)
P01139 Power Supply/Battery Charger (not shown)
1 P02491 Base, TITAN MDS
2 P02500 VCR/Printer Enclosure, TITAN MDS
3 P02505 Tray, TITAN MDS
4 P02506 Front Panel, TITAN MDS
5 P02507 Rear Door, TITAN MDS

Table A.7: Replaceable Parts List (Continued)
Find Number Part Number Part Description
6 P02952 Foot Pedal, TITAN MDS
7 P03132 Cable Cover, TITAN MDS
8 P03133 Cup Surround, TITAN MDS
P03300 Gas Spring, TITAN MDS (not shown)
9 P03301 Hook, Cable, TITAN MDS
P03302 Outlet Strip, IEC
10 P03303 Button, Release, TITAN MDS
11 P03304 Printer Strap, TITAN MDS
12 P03306 Handle, TITAN MDS
13 P03307 Head Support, TITAN MDS
14 P03310 Caster, Total Lock
15 P03418 Shelf, VCR
P03443 Assembly, Latch Link (not shown)
16 P03499 Release, Back Door
17 P03500 Caster, Swivel
18 P03595 Deflector, Ejector
P03610 Latch Spindle, Machined (not shown)
19 P03611 Latch Hook, Machined
P03613 Latch Lever, Machined (not shown)
P03653 Spring, Cover (not shown)

A.1.8 Triple Transducer Connect
Note: The Triple Transducer Connect utilizes the same Nest Frame Assembly parts as the Titan Main PCBA. Refer to
Section A.1.4 for these parts.
Figure A.14 Triple Transducer Connect Cable
Table A.8: Triple Transducer Connect Cable
P04195 Service Assembly, Triple Transducer Connect Cable
P00481 Latch Handle Shaft
P00522 Spring, Shaft, Main
P00624 Cover Scanhead Interface, Coax Bundle
P00900 Plunger, Spring
P01304 Handle, Latch
P01305 Cover, Latch Handle
P03708 Enclosure, Scanhead Interface
P03709 Clamp, Enclosure, Scanhead Interface
P03713 Shaft, Latch
P03768 Assembly, Cable, Transducer Select Module

Figure A.15 Triple Transducer Connect
Table A.9: Triple Transducer Connect
P03315 Assembly, PCB,TTC
P03699 Enclosure, Bottom, TTC
P03700 Frame, TTC
P03707 Cable Clamp, TTC
P03747 Spacer, Mounting, TTC
P03756 Cover, Spring
P03902 Assembly, Top Enclosure, TTC
A.2 Ordering Replacement Parts

To order parts, contact SonoSite Technical Support as indicated in Section 8.6, “Returning Products to SonoSite,”
on page 67.

Appendix B: Service Event Report
The Service Event Report provides information about product failures to the manufacturer and to authorized
service facilities, which provide approved warranty services for SonoSite products. For all repairs completed,
complete the form and return a copy of it to the following address:
SonoSite, Inc.
Technical Support
21919 30th Drive SE
Bothell, Washington 98021
USA

Features
Appendix B: Service Event Report 105

Service Event Report
Service Provider
Name: Date:
Company:
Address:
Phone Number: Fax Number:
E-mail address:
Device Description
Name: Serial Number:
Part Number: Lot Number: Revision:
Software Version: Other Identifiers:
Event Description
Diagnosis
Service Performed
Performed By: Date:
Actions:
Parts Removed
Part Name Part Number Serial Number Lot Number Rev Replaced By
Parts Installed
Part Name Part Number Serial Number Lot Number Rev Replaced By
Tests Performed (attach test data)

Test: Test:
Performed By: Performed By:
Result: Pass Fail Result: Pass Fail
Attach additional sheets as required
Page ____ of ____ F00019 Rev B
106 Appendix B: Service Event Report

Index
Numerics E
2D performance tests error message 6
axial measurement accuracy 62 external power 25
image quality 62
lateral measurement accuracy 63
penetration 63 F
forms 22
freeze 22
A
AC power indicator 21
accessories 16 G
acquisition subsystem 10 gain 21
alphanumeric 21 grace period 4
annotation 21
assert code 42
assistance, customer 1
I
image
problem 39
B quality verification test 65
battery review 65
installation 25
safety 6
specifications 18
L
storage and shipping 18 license key
troubleshooting diagram 46 install 34
battery charging test 66 obtain 34
license update screen, display 35
C
cable specifications 17
M
main PCBA
cable, connect mobile docking system 71
failures 41
caliper/calcs 22
replacement procedure 55
cautions 5
mini-dock
connectivity 71
connectivity 27, 71
control panel assembly
description 71
service 71
troubleshooting diagram 44
control subsystem 14
mobile docking system
conventions used 1
connectivity 71
description 69
D service 69
depth 21 troubleshooting diagram 47
display mobile docking system connectivity 27
failures 41 modes 22
subsystem 12 monitor 16
display assembly moving image 64
duplex images 24
Index 107
P system
charging requirements 26
performance tests
dimensions 16
2D 62
information screen 35
battery 66
insert 70
CPD 64
measurement accuracy 63
DCPD 64
overview 9
M mode 65
remove 70
overview 61
software 4
printer 66
specifications 16, 18
PW 65
THI 65
upgrade software 29
video output 66
system control
peripherals 17
AC power indicator 21
phantoms
alphanumeric 21
RMI 1425A Doppler 61
annotation 21
RMI 403 GS Multipurpose 61
caliper/calcs 22
RMI 413A Soft Tissue 61
depth 21
RMI 425 Doppler 61
power forms 22
battery charge indicators 26 freeze 22
battery pack 25 gain 21
subsystem 15 modes 22
power supply replacement procedure 57 power 21
print 22 print 22
printer remappable controls 22
problem 39 save 22
test 66 select 22
processing subsystem 12 THI 21
product failures, reporting 105 touchpad 22
products, returning 67 update 22
video recording 22
zoom 21
R system setup
recording problem 39 beep alert 23
replacement parts connectivity 24
list 89 date 23
ordering 103 delta key 23
return material authorization number (RMA) 67 Doppler scale 23
duplex images 24
F keys 23
S key click 23
safety, ergonomic 5 mode data 23
save image 22 OB authors 23
service event report 105 patient header 23
shipping instructions 67 power delay 23
software printer 24
license 4, 34 sleep delay 23
upgrade 29 system information 24
SonoSite technical support, contact 67 system status 23
speaker replacement 57 thermal index 24
subassembly replacement 40 time 23
video mode 24
108 Index
T V
technical support, contact 67 VCR problem 39
THI 21 video output tests 66
touchpad 22 video recording 22
transducer
acquisition subsystem 10
problems 40 W
specifications 16, 18 warnings 5
storage and shipping 18
troubleshooting symptoms table 39
Z
zoom
U description 21
update 22 problem 39
Index 109
110 Index

TitanServiceManual PDF

Uploaded by

Document Informationclick to expand document information

Document Informationclick to expand document information

Copyright:

Available Formats

TitanServiceManual PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

TitanServiceManual PDF

Uploaded by

Copyright:

Available Formats

Ultrasound System

“TITAN” and “SonoSite TITAN” are trademarks of SonoSite, Inc.

Kensington is a registered trademark of Kensington Technology Group.

Chapter 3: System Overview

Chapter 4: Setup and Operation

Chapter 5: Cleaning and Disinfecting

Chapter 7: Replacement Procedures

Chapter 8: Performance Testing

Chapter 9: Accessory Service

Appendix A: Parts List

Appendix B: Service Event Report

1.2 Conventions Used in This Service Manual

1.3 Product Upgrades and Updates

1.4 Customer Comments

Figure 1.1 TITAN System Front View

Table 1.1: TITAN System Front Features

Figure 1.2 TITAN System Rear View

Table 1.2: TITAN System Rear Connectors

4 ECG connector (available on future releases)

1.7 Software Licensing

2.1 Electrical Safety

2.2 Equipment Safety

2.3 Battery Safety

2.4 Biological Safety

2.5 Labeling Symbols

3.1 System Overview

3.2 Theory of Operation

Chapter 3: System Overview 9

3.2.2 Front End Subsystem

10 Chapter 3: System Overview

Chapter 3: System Overview 11

Figure 3.3 Digital Signal Processing Subsystem

3.2.4 Backend Subsystem

12 Chapter 3: System Overview

Figure 3.4 BackEnd Subsystem Block Diagram

Chapter 3: System Overview 13

Figure 3.5 Control Subsystem

14 Chapter 3: System Overview

VEXT Standby Power VSTBY

Figure 3.6 Power Supply and Control System Block Diagram

Chapter 3: System Overview 15

3.3.1 System Dimensions

3.3.2 Display Dimensions

3.3.4 Imaging Modes

16 Chapter 3: System Overview

3.3.8.1 Medical Grade

3.3.8.2 Non-Medical Grade

Chapter 3: System Overview 17

3.3.11 Electromechanical Safety Standards

3.3.12 EMC Standards Classification

18 Chapter 3: System Overview

3.3.14 ECG Standard

3.3.15 DICOM Standard

Chapter 3: System Overview 19

4.1 System Controls

Figure 4.1 System Controls

Table 4.1: System Controls