Scribd
Upload
760 views2 pages

Bushing ABB

This certified test report summarizes the test results for a 46 kV condenser bushing. The bushing passed tests measuring its power factor, capacitance, 60 Hz withstand voltage, and partial discharge. Key results included a power factor of 0.26% and capacitance of 424 pF for measurements between the stud and tap, and a power factor of 0.24% and capacitance of 424 pF for measurements between the tap and flange. The bushing also passed a 2 kV tap test and dry 60 Hz withstand and partial discharge tests up to 125 kV.

Uploaded by

edgard
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
760 views2 pages

Bushing ABB

This certified test report summarizes the test results for a 46 kV condenser bushing. The bushing passed tests measuring its power factor, capacitance, 60 Hz withstand voltage, and partial discharge. Key results included a power factor of 0.26% and capacitance of 424 pF for measurements between the stud and tap, and a power factor of 0.24% and capacitance of 424 pF for measurements between the tap and flange. The bushing also passed a 2 kV tap test and dry 60 Hz withstand and partial discharge tests up to 125 kV.

Uploaded by

edgard
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 2

*046W2000UD* **

Alamo, Tennessee
CERTIFIED TEST REPORT
Status: Passed

5/27/2013 11:25:31
Test Date:
PM
Condenser 2226148
Apparatus: ABB Job Number:
Bushing 1
ABB Order
Bushing Type: O Plus C
Number:
Style: 046W2000UD Version: 5
Rating: 46 kV
BIL: 250 kV
Max L-G Voltage: 29 kV
2000 Amps (Bottom
Serial Number:
Connected)
Ambient
24 oC Humidity: 51%
Temperature:
1. Power Factor and Capacitance
The power factor/capacitance test is conducted per IEEE Std.
C57.19.00-2004 & Std. C57.19.01-2000. Test equipment includes a
dielectric test set for measurements above 10kV and a
dissipation factor/capacitance bridge #018
Before 60 Hz Withstand
Applied Power Factor Capacitance
Measurement
kV (%) (Pfd)
(C1) Stud to
10 .26 424
Tap
(C2) Tap to
1 NA NA
Flange
Stud to Flange 10 NA NA
2. Tap Test: 2 kV 60 Hz one minute applied test, tap to flange:
Passed

3. Dry 60 Hz Withstand and Partial Discharge:


The tests were conducted per IEEE Std. C57.19.00-2004, IEEE
Std. C57.19.01-2000 specifications. The dielectric and partial
discharge detection equipment is designed to meet or exceed
IEEE 454-1973, C57.113-1991, and C63.2-1996 requirements which
includes dividers, detectors, power sources to 1MV, and partial
discharge detectors. For units requiring partial discharge in
microvolts, tests are conducted per NEMA 107-1987.

Start Finish
Test Voltage (kV) Test Duration (Min) PC PC
44 NA 1 NA
125 1 2 1
44 NA 1 NA
NA NA NA NA
NA NA NA NA
4. After 60 Hz Withstand (Nameplate information):

Applied Power Factor Capacitance


Measurement
kV (%) (Pfd)
(C1) Stud to
10 .26 424
Tap
(C2) Tap to
1 .24 424
Flange
Stud to Flange 10 NA NA
5. The pressure and vacuum sealing of this bushing has been verified by testing in accordance with IEEE
C57.19.00 - 2004 section 7.4.5. This unit was filled at the factory with PCB-free (non-detectable) dielectric
fluid in accordance with U.S. Federal polychlorinate biphenyl (PCB) regulation 40 CFR 61, dated May 31,
1979. The analysis is verified per ASTM-D4059 with a detection level of less than 1 ppm. Bushings are
filled with mineral oil that is certified passivator free and certified tested corrosive sulfer free. All tests
were conducted on bushings that meet or exceed IEEE C57.19.00-2004.
All dielectric withstand levels for power frequency meet or exceed the routine test levels required by the
applicable IEC standards.

Test Specialist: Ej Jelks Date: 5/27/2013 11:25:31 PM

Remarks:

*.26* *424* *.24* *424*

Form: CTR-Condenser Bushings/IEEE v1.0 Form Date: 1/1/2000

You might also like