PROGRAMMING MANUAL

English

Code: P2935EN00 Date: 10 - 2007

 Introduction
This “Programming Manual” is a very useful tool for those operators who want to get the most out of the poten-
tial of the installed software and know in detail all of the available software functions.
This document is available in PDF format in the Reserved Area of our internet site
www.nwglobalvending.com or, on request, through our after-sales service.

The Manual is divided into 3 parts:

The First Part regards Normal Vending Mode; it describes the operations to be carried out during the vending
machine normal use:
- Power-on
- Operations with the door closed
- Messages for the user.
The Second Part descries the Filler Menu, the programming part that is used for changing individually the
sales prices of the selections and for simple controls on the functioning and on the machine sales.
The Third Part describes the Technician Menu, the programming part that is meant for technical personnel,
used for changing the machine performance.
The operations described can modify the functioning cycles, therefore they must be carried out only by per-
sonnel who have the specific knowledge of the machine functioning from a point of view of electrical safety
and health regulations.
The appendix contains the List of Failures, which describes the possible error signals and the self-diagnosis
conditions of the machine; it also describes the functions concerning the coin mechanism communication
protocols.

normal vending mode

Power On
When closing the machine door, the display indicates the version number of the installed software.
The machine can be programmed for displaying, for a few second, the number of selections made.

After a few seconds the display will show the message “Heating” and when the normal operating temperature
is reached, the machine goes into normal vending mode.

P2935EN00 10 - 2007
A
Messages for the user
The following table indicates the most common strings that may be shown on the machine display in normal
vending mode.

String Description
It is not possible to make selections. The boiler heating element is
HEATING switched on and is heating the water to bring it to normal operat-
ing temperature.
The machine waits for the user to make a drink selection by press-
SELECT THE DRINK ing the relevant selection button.
The machine signals that, in the event the money in the tubes is
NO CHANGE lower than the required minimum, the change is not guaranteed.
please wait The machine is preparing the selected drink.
The machine has completed the preparation of the selected drink.
TAKE THE PRODUCT
The machine signals that an error or a malfunctioning has taken
dispensing failed place which does not allow the distributor to correctly distribute
the selected drink.
It is not possible to make selections. Besides this message, the
VENDING MACHINE OUT OF ORDER failure that caused this condition is displayed alternating.
It is not possible to make selections. This condition occurs when
SUSPENDED SERVICE the machine is in Energy Saving mode or while dispensing a prod-
uct from the slave machine.
It is not possible to make espresso coffee based selections,
ESPRESSO OUT OF ORDER because of a failure in the coffee unit. All other selections remain
available.
It is not possible to make the selection chosen, as such selection
SELECTION DISABLED was disabled in the programming menus.
The machine signals that there are no cups in the distributor but it
No cups is possible to place a cup in the dispensing areas.
This option is available only if a cup sensor is mounted (optional).

P2935EN00 10 - 2007
B
 programming menu
In order to access the programming menu, open the front door of the vending machine, switch on the machine
and insert the yellow key supplied in the relevant slot located on the left-hand side of the machine.

Press the programming access button as shown in the figure:

The machine goes into "Filler Menu" mode.
The buttons shown in the figure are used for surfing through the different menus:

Scrolling buttons UP “�”and DOWN “�”

The UP and DOWN scrolling buttons are used for moving from one programming menu item to the next one,
located in the same level, and at the same time change the status or the numeric value of the corresponding
functions.
Confirm / Enter button “�”
The confirm / enter button is used for moving to the lower level or for confirming a value after being entered or
changed.
Exit button “�”
The exit button is used for returning to the higher level or for exiting a change field of a function. When reach-
ing the highest level in the menu, this button is pressed for going from the Technician menu into the Filler menu
and vice versa.

P2935EN00 10 - 2007
C
 FILLER Menu

1
1 - STATISTICS Statistics

1.1
1.1 - PRINT STATISTICS Printing the Statistics

1.1.1
1.1.1 - PARTIAL PRINTOUT Partial printout

1.1.1.1
1.1.1.1 - PRINT SEL. COUNT Printing the selection counters
When confirming this function, the counters regarding the different
selections are printed.

1.1.1.2
1.1.1.2 - PRINT BAND COUNT Printing the time band counters
When confirming this function, the counters regarding the different
time bands are printed.

1.1.1.3
1.1.1.3 - PRINT DISC COUNT Printing the discount counters
When confirming this function, the counters regarding discounts
and overprice are printed.

1.1.1.4
1.1.1.4 - PRINT FAIL COUNT Printing the failure counters
When confirming this function, the counters regarding the different
failure are printed.

1.1.1.5
1.1.1.5 - PRNT C MECH DATA Printing the coin mechanism data
When confirming this function, the counters regarding the coin
mechanism data are printed.

P2935EN00 10 - 2007
1
 FILLER Menu

1.1.2
1.1.2 - TOTAL PRINTOUT Total printout
When confirming this function, all statistics are printed.

1.2
1.2 - PRINT REL. STATS. Printing the relative statistics

1.2.1
1.2.1 - PARTIAL PRINTOUT Partial printout

1.2.1.1
1.2.1.1 - PRINT SEL. COUNT Printing the selection counters
When confirming this function, the relative counters regarding the
different selections are printed.

1.2.1.2
1.2.1.2 - PRINT BAND COUNT Printing the time band counters
When confirming this function, the relative counters regarding the
different time bands are printed.

1.2.1.3
1.2.1.3 - PRINT DISC COUNT Printing the discount counters
When confirming this function, the relative counters regarding dis-
counts and overprice are printed.

1.2.1.4
1.2.1.4 - PRINT FAIL COUNT Printing the failure counters
When confirming this function, the relative counters regarding fail-
ures are printed.

1.2.1.5
1.2.1.5 - PRNT C MECH DATA Printing the coin mechanism data
When confirming this function, the relative counters regarding the
coin mechanism data are printed.

P2935EN00 10 - 2007
2
 FILLER Menu

1.2.2
1.2.2 - TOTAL PRINTOUT Total printout
When confirming this function, all relative statistics are printed.

1.3
1.3 - DISPLAY STATS Displaying the statistics

1.3.1
1.3.1 - DIS. SEL. COUNT. Displaying the selection counters

1.3.1.1
1.3.1.1 - DIS. SIN. COUNT. Displaying the single counters
This function is used for displaying the counters regarding each
selection, divided by price band (0, 1, 2, 3, 4, Free, Test).

1.3.1.2
1.3.1.2 - DIS. TOT. COUNT. Displaying the total counters
This function is used for displaying the total counters regarding each
selection.

1.3.1.3
1.3.1.3 - DIS. SEL. COUNT. Displaying the selection counters in normal vending - /maintenance
This function is used for displaying the total counters regarding the
selections made while in normal vending mode and maintenance
mode.

1.3.2
1.3.2 - DIS. BAND COUNT. Displaying the time band counters
When selecting the desired price band (0, 1, 2, 3, 4, Free, Test), the
total number of selections made for that price band is displayed.

1.3.3
1.3.3 - DIS. DISC. SEL. Displaying the discount counters
This function is used for displaying the total amount of discounts
and overprice accumulated for the dispensed selections.

P2935EN00 10 - 2007
3
 FILLER Menu

1.3.4
1.3.4 - DIS. FAIL.COUNT. Displaying the failure counters
This function is used for displaying the number of times each pos-
sible failure occurred in the vending machine.

1.3.5
1.3.5 - DIS. C MECH DATA Displaying the coin mechanism data

1.3.5.1
1.3.5.1 - DIS. AUDIT DATA Displaying the audit data
This function is used for displaying the number of coins inserted in
the vending machine, differentiated by the type of coin.

1.3.5.2
1.3.5.2 - DIS. CASH COUNT. Displaying the cashed amount
This function is used for displaying the value of:
- Total cashed
- Total sold
- Total cashed by credit

1.4
1.4 - DIS. REL. STATS Displaying the relative statistics

1.4.1
1.4.1 - DIS. SEL. COUNT. Displaying the selection counters

1.4.1.1
1.4.1.1 - DIS. SIN. COUNT. Displaying the single counters
This function is used for displaying the counters regarding each
selection, divided by price band (0, 1, 2, 3, 4, Free, Test).

1.4.1.2
1.4.1.2 - DIS. TOT. COUNT. Displaying the total counters
This function is used for displaying the total counters regarding each
selection.

P2935EN00 10 - 2007
4
 FILLER Menu

1.4.1.3
1.4.1.3 - DIS. SEL. COUNT. Displaying the selection counters in normal vending - maintenance
This function is used for displaying the total counters regarding the
selections made while in normal vending mode and maintenance
mode.

1.4.2
1.4.2 - DIS. BAND COUNT. Displaying the time band counters
When selecting the desired price band (0, 1, 2, 3, 4, Free, Test), the
total number of selections made for that price band is displayed.

1.4.3
1.4.3 - DIS. DISC. SEL. Displaying the discount counters
This function is used for displaying the total amount of discounts
and overprice accumulated for the dispensed selections.

1.4.4
1.4.4 - DIS. FAIL.COUNT. Displaying the failure counters
This function is used for displaying the number of times each failure
occurred in the vending machine.

1.4.5
1.4.5 - DIS. C MECH DATA Displaying the coin mechanism data

1.4.5.1
1.4.5.1 - DIS. AUDIT DATA Displaying the audit data
This function is used for displaying the number of coins inserted in
the vending machine, differentiated by the type of coin.

1.4.5.2
1.4.5.2 - DIS. CASH COUNT. Displaying the cashed amount
This function is used for displaying the value of:
- Total cashed
- Total sold
- Total cashed by credit

1.5
1.5 - DEL. REL. STATS. Deleting the relative statistics

P2935EN00 10 - 2007
5
 FILLER Menu

1.5.1
1.5.1 - DELETE PARTIAL Partial delete

1.5.1.1
1.5.1.1 - DELETE SE. COUNT Deleting the selection counters
When confirming this function, the counters regarding the different
selections are deleted.

1.5.1.2
1.5.1.2 - DEL. DISC. COUNT Deleting the discount counters
When confirming this function, the counters regarding discounts
and overprice are deleted.

1.5.1.3
1.5.1.3 - DEL. FAIL. COUNT. Deleting the failure counters
When confirming this function, the counters regarding the different
failure are deleted.

1.5.1.4
1.5.1.4 - DEL. C MECH DATA Deleting the coin mechanism data
When confirming this function, the counters regarding the coin
mechanism data are deleted.

1.5.2
1.5.2 - DELETE TOTAL Total delete
When confirming this function, all relative statistics are deleted.

P2935EN00 10 - 2007
6
 FILLER Menu

2
2 - PREZZI Prices

2.1
2.1 - Setting global prices Setting global prices

2.1.1
2.1.1 - Price band 0 Price band 0
This function is used for setting a single price for all available
selections.

2.2
2.2 - SET SIN. PRICES Setting single prices

2.2.1
2.2.1 - Price band 0 Price band 0
This function is used for setting a different price for each selection.

3
3 - tube control Change tubes control

3.1
3.1 - Filling tube Filling the change tubes
From this function, the change tubes can be filled manually.
Confirming the refilling, the display will indicate
“Credit: ——” which is the value of money available in the change
tubes; insert the desired coin into the validator and the display will
indicate the value of money available in the change tubes.

3.2
3.2 - Releasing tubes Releasing the change tubes
From this function, the change tubes can be released manually.
When confirming the releasing, it will be possible to decide which
tube to release. Each time the confirm button is pressed, a coin is
ejected from the active tube.

P2935EN00 10 - 2007
7
 FILLER Menu

4
4 - BOILER TEMPERAT. Boiler temperature
This function is used for displaying the operating temperature, ex-
pressed in °C, of the boilers actually installed in the machine.

5
5 - TEST Test

5.1
5.1 - COMP. DISPENSING Complete dispensing
With this function it is possible to obtain, with the door open
and without inserting any money, complete dispensing for each
selection.

5.2
5.2 - WATER ONLY Water only
With this function it is possible to dispense, with the door open
and without inserting any money, only the water doses for each
selection.

5.3
5.3 - POWDER ONLY Powder only
With this function it is possible to dispense, with the door open
and without inserting any money, only the powder doses for each
selection.

5.4
5.4 - NO ACCESSORIES No accessories
With this function it is possible to dispense, with the door open and
without inserting any money, only the water and powder doses for
each selection, without any cup and stirrer.

5.5
5.5 - ACCESSORIES ONLY Accessories only
With this function it is possible to dispense, with the door open
and without inserting any money, only the accessories for each
selection.

P2935EN00 10 - 2007
8
 FILLER Menu

6
6 - GSM GSM

6.1
6.1 - RESET PRE-AL CNT Resetting the pre-alarm counters
With this function the counters that control the pre-alarms are reset.

7
7 - EVADTS Evadts

7.1
7.1 - CONNECTION Connection
This function places the machine in wait mode for connection to
retrieve data.

P2935EN00 10 - 2007
9
 TECHNICIAN Menu

1.
1 - FAILURES Failures

1.1
1.1 - READING FAILURES Reading the failures
When the “Failure” function is displayed, press the confirm button
“�” to display the present failures.
If no failures are currently present, after pressing the confirm button
“�” the message “End failures” will be displayed.
A detailed description of the possible failures present in these
models is indicated in the appendix of this manual.

1.2
1.2 - RESET FAILURES Resetting the failures
By confirming this function all current failures will be reset.

1.3
1.3 - LED OUT SERV. Led lighting out of service
This function is used for setting whether or not the LED lighting for
the push-buttons are to be switched on when the machine is out of
service or during the “Energy saving” time band.

P2935EN00 10 - 2007
10
 TECHNICIAN Menu

2
2 - SET PARAMETERS Setting the parameters

2.1
2.1 - CASH Cash
This set of functions controls all parameters regarding the payment
systems and the sales prices.

2.1.1
2.1.1 - PRICES Prices
Four different prices can be set for each selection according to the
programmed time bands for when the time table option is enabled.
For each of the 4 time bands prices (0 to 65,535) can be pro-
grammed globally (same price for all selections) or for the single
selections.

2.1.1.1
2.1.1.1 - SET SIN. PRICES Setting single prices

2.1.1.1.1
2.1.1.1.1 - Price band 0 Price band 0
This function is used for setting a different price for each selection in
time band 0.

2.1.1.1.2
2.1.1.1.2 - Price band 1 Price band 1
This function is used for setting a different price for each selection in
time band 1.

2.1.1.1.3
2.1.1.1.3 - Price band 2 Price band 2
This function is used for setting a different price for each selection in
time band 2.

2.1.1.1.4
2.1.1.1.4 - Price band 3 Price band 3
This function is used for setting a different price for each selection in
time band 3.

2.1.1.1.5
2.1.1.1.5 - Price band 4 Price band 4
This function is used for setting a different price for each selection in
time band 4.

P2935EN00 10 - 2007
11
 TECHNICIAN Menu

2.1.1.2
2.1.1.2 - SET GLOB. PRICES Set global prices.

2.1.1.2.1
2.1.1.2.1 - Price band 0 Price band 0
This function is used for setting one price for all available selections
in time band 0.

2.1.1.2.2
2.1.1.2.2 - Price band 1 Price band 1
This function is used for setting one price for all available selections
in time band 1.

2.1.1.2.3
2.1.1.2.3 - Price band 2 Price band 2
This function is used for setting one price for all available selections
in time band 2.

2.1.1.2.4
2.1.1.2.4 - Price band 3 Price band 3
This function is used for setting one price for all available selections
in time band 3.

2.1.1.2.5
2.1.1.2.5 - Price band 4 Price band 4
This function is used for setting one price for all available selections
in time band 4.

P2935EN00 10 - 2007
12
 TECHNICIAN Menu

2.1.1.3
2.1.1.3 - TIME BANDS Time bands
Four programmable time bands are provided for selling products at
different prices.
Time band 0 is not programmable and covers the 24 hours.

2.1.1.3.1
2.1.1.3.1 - SET DATE & TIME Set Date and Time
This function is used for setting the reference time given by an inter-
nal clock programmable for:
day/month/year/week-day 1-7 (1=Monday, 2=Tuesday, etc…) and
then hour/minutes/seconds.

2.1.1.3.2
2.1.1.3.2 - TIME BAND 1 Time Band 1
The time bands are programmable for beginning and end time by
hours (00 to 23) and minutes (00 to 59). If the values for start and
end of the time band are set to 00.00 the time period is disabled.

2.1.1.3.3
2.1.1.3.3 - TIME BAND 2 Time Band 2
The time bands are programmable for beginning and end time by
hours (00 to 23) and minutes (00 to 59). If the values for start and
end of the time band are set to 00.00 the time period is disabled.

2.1.1.3.4
2.1.1.3.4 - TIME BAND 3 Time Band 3
The time bands are programmable for beginning and end time by
hours (00 to 23) and minutes (00 to 59). If the values for start and
end of the time band are set to 00.00 the time period is disabled.

2.1.1.3.5
2.1.1.3.5 - TIME BAND 4 Time Band 4
The time bands are programmable for beginning and end time by
hours (00 to 23) and minutes (00 to 59). If the values for start and
end of the time band are set to 00.00 the time period is disabled.

P2935EN00 10 - 2007
13
 TECHNICIAN Menu

2.1.2
2.1.2 - COIN MECHANISMS Coin mechanisms

2.1.2.1
2.1.2.1 - COIN MECH SETT. Setting the coin mechanisms
It is possible to decide which of the payment system protocols avail-
able are to be enabled for the functions.
The available payment systems are:
- Executive
- Validators
- BDV
- MDB
By selecting one of the systems it is possible to control its functions.
A detailed description of the functions related to the commu-
nication protocols is indicated in the appendix of this manual.

2.1.2.2
2.1.2.2 - IMMEDIATE CHANGE Immediate change
This function is valid only in the case where a change-giver coin
mechanism is installed in the machine.
Normally the amount for a selection is cashed after the machine
sends the message “Selection successful”, consequently the
change is returned at the end of dispensing the selected product.
By enabling this function, disabled by default, the cashed signal is
sent at the beginning of dispensing, consequently the change owed
to the user is returned at the same time of dispensing the product.

2.1.3
2.1.3 - DECIMAL POINT Decimal point
Press the confirm button “�” to display the position of the decimal
point, i.e.:
0 decimal point disabled
1 XXX.X
2 XX.XX
3 X.XXX
Press the confirm button “�”, these values will start blinking and
can then be modified as necessary.

P2935EN00 10 - 2007
14
 TECHNICIAN Menu

2.1.4
2.1.4 - MASTER SLAVE Master Slave
The machine control system is pre-arranged for the connection in a
bank of vending machines (Snakky and Snakky SL)

2.1.4.1
2.1.4.1 - SET UP Settings
This function is used for setting the hierarchies of master/slave rela-
tionships between connected vending machines.
This machine can be configured a “Master”, i.e. having control over
the second machine, or as “Slave”, i.e. leaving the control to the
other machine.
2-digit (XX) or 3-digit (0XX; 9XX) selection numbers will also be set.
The master/slave function is not enabled by default.

2.1.4.2
2.1.4.2 - SLAVE PRICE HOLD Slave Price Holding (Exe. Protocol)
In the event an Executive payment system in “Price Holding” mode
is set, this function is used for setting the same mode also in the
software of the slave machine.

2.1.4.3
2.1.4.3 - REST.PREZZO VIRT Virtual Price Return (EXE. / BDV Protocol)
In the case of combined or virtual selections (with the related menus
present in the slave machines), this function is used for setting
whether to keep (OFF) or not (ON) the partial amount, should the
second selection/dispensing fail.

2.1.4.4
2.1.4.4 - RESET SNAKKY SL Reset snakky sl
This function is used for resetting all settings related to the master/
slave function on the slave machine.

2.1.4.5
2.1.4.5 - MONITOR SLAVE Monitor Slave
This function is used for scrolling through all the information of a
slave being connected.
When switching on the slave with the display showing this function,
the display will indicate in a sequence all information on the slave
regarding:
- software version
- type of slave (XX, 0XX, 9XX)
- presence of dispensing detection photocells
- number of trays and compartments
- presence of dispensing compartment lock device
- temperature detected by the internal probe
To exit the function it will be necessary to switch the master machine
off.

P2935EN00 10 - 2007
15
 TECHNICIAN Menu

2.1.5
2.1.5 - FREE VEND. BONUS Free vend bonus
This function, compatibly with the national laws, permits the dis-
pensing of a free product every certain programmable number of
sold selections. In any case the free selection is random within the
programmed number.
The machine emits an intermittent sound signal and the display
indicates a congratulations message.

2.2
2.2 - SELECTIONS Selections

2.2.1
2.2.1 - SET WATER Setting the water

2.2.1.1
2.2.1.1 - WATER DOSES Water doses
With this function the water doses that compose the drink can be
set for each selection button.
These are expressed in:
- cc for instant products;
- fmp (number of pulses of the volumetric counter) for Espresso
(coffee or tea).
The display will indicate the number of the water dose being set
(water 1, water 2, etc.) and the water value blinking. In order to verify
the correspondence between the water doses refer to the “Selection
dose table”.

2.2.1.2
2.2.1.2 - SET WHIP DOSES Setting the whipper

2.2.1.2.1
2.2.1.2.1 - SET DOSES Setting the whipper doses
The whipping time can be set for each selection button, for each
water dose that composes such selection.
The duration can be set in two different modes:

2.2.1.2.2
2.2.1.2.2 - SET MODALITY Setting the whipper mode
It is possible to choose between two different modes:
Absolute
i.e. independent from the solenoid valve opening time. The whip-
ping duration is set as tenths of a second for Instant models and as
volumetric counter pulses for Espresso models.
Relative
i.e. based on the difference, plus or minus, from the moment the
solenoid valve closes.
The whipping duration is always expressed in tenths of a second.

P2935EN00 10 - 2007
16
 TECHNICIAN Menu

2.2.1.3
2.2.1.3 - SOLENOID SETTING Solenoid valve settings
It is possible to set the water flow rate of the single solenoid valves
expressed in cc/s (the default value setting in cc/s is indicated in
the selection dose table) to calculate the amount of water to be
dispensed.

2.2.1.4
2.2.1.4 - DRIPPING TIME Set Dripping Time
The wait time (programmable from 0 to 2000 hundredths of a sec-
ond) to the emission of an “end of dispensing” warning sound can
be set for each selection in order to allow the tubes to drain.

2.2.2
2.2.2 - SET POWDER Setting the powders

2.2.2.1
2.2.2.1 - POWDER DOSES Powder doses
This function is used for setting, for each selection button, the in-
stant product powder doses that compose the drink.
These are expressed in gr. (grams).
The display will indicate the combination of water and powder being
set (water 1 - powder 1, etc.) and the powder dose value blinking.
In order to verify the correct correspondence refer to the “Selection
dose table”.

2.2.2.2
2.2.2.2 - DOSER SETTINGS Setting the doser units

This function is used for setting the flow rate of the single doser
units, expressed in g/s, to calculate the amount of powder to be
dispensed, for correct conversion of product dose values..

2.2.2.3 - Glob. powd. doses 2.2.2.3

Global powder doses
With this function it also possible to program the doses of a product
"Globally", i.e. setting all selections with a single operation.

P2935EN00 10 - 2007
17
 TECHNICIAN Menu

2.2.3
2.2.3 - SET ACCESSORIES setting the accessories

2.2.3.1
2.2.3.1 - ENABLE CUP enabling the cup

This function is used for enabling or disabling cup dispensing for

each selection button.

2.2.3.2
2.2.3.2 - ENABLE SUGAR enabling the sugar

This function is used for enabling or disabling sugar dispensing for

each selection button.

2.2.3.3
2.2.3.3 - ENABLE STIRRER enabling the stirrer

This function is used for enabling or disabling stirrer dispensing for

each selection button.

2.2.4
2.2.4 - SELECTION STATUS Selection status
Each single selection button can either be enabled or disabled.

2.2.5
2.2.5 - BUTTON SELECTION Button <--> Selection
This function permits the association of a selection number, indi-
cated in the selection dose table, to a button in the direct selection
keypad.

2.2.6
2.2.6 - SEL. ARRANGEMENT Checking the selection number
Verifying the selection number (for direct selection models only) as-
sociated to a button.

2.2.7
2.2.7 - PRODUCT CODE Setting the product code
This function is used for assigning a 4-digit code to each selection
for processing the statistics.

P2935EN00 10 - 2007
18
 TECHNICIAN Menu

2.3
2.3 - MACHINE PARAM. Vending machine parameters

2.3.1
2.3.1 - BOILER TEMPERAT. Boiler temperature
This function is used for setting the operating temperature, ex-
pressed in °C, of the boilers actually installed in the machine.
After selecting the boiler, press the confirm button “�”, the tempera-
ture value will start blinking and can be modified as necessary.

2.3.2
2.3.2 - TANk Tank
The machine water supply can be from the mains or from an internal
tank. For some applications it is also possible to use two internal
tanks at the same time.
With this function it is possible to define whether the machine water
supply is from the mains (tank = 0) or from the tanks (tank = 1 or 2).

2.3.3
2.3.3 - MIXER HEATING Mixer heating
With this function it is possible to heat the mixer with a small amount
of hot water before dispensing, as long as the following conditions
are met:
- the first water dose composing the drink is below 60 cc;
- no hot drinks have been dispensed from the mixer in the last 3 min-
utes, or no cold drinks have been dispensed in the last 5 minutes.

2.3.4
2.3.4 - MIXER COOLING Mixer cooling (only for machines with a cold unit)
With this function it is possible to cool the mixer with a small amount
of cold water before dispensing, if no cold drinks have been dis-
pensed from the mixer in the last 5 minutes, or no hot drinks have
been dispensed in the last 3 minutes.

2.3.5
2.3.5 - FAST CYCLES Fast cycles
When this function is enabled, some of the time that is useful for
improving the drink quality is eliminated: all products that compose
the drink are dispensed at the same time, eliminating the “post-
whipping” time.

P2935EN00 10 - 2007
19
 TECHNICIAN Menu

2.3.6
2.3.6 - SET DISP. MAINT. Setting the regeneration counter
It is possible to display the message “Regenerate the water sof-
tener” upon accessing “Filler” mode after a programmable number
of drinks dispensed.

2.3.7
2.3.7 - Photocell Cup Sensor
The machine can be fitted with a “cup sensor” composed of pho-
tocell that detects the presence of an object in the dispensing
compartment.
When the function is enabled, if an object is detected in the dis-
pensing compartment, a cup is not released and the display indi-
cates the message “Without cup”.
It is also possible to define whether, after two attempts to release
a cup without the photocell detecting any objects in the dispensing
compartment; the failure should lock the machine or leave it to oper-
ate using a ceramic cup.
A lighting lamp inside the dispensing compartment is controlled by
the cup sensor.
If the cup is still inserted, when the next selection is made the mes-
sage "Remove cup" is displayed.

2.3.8
2.3.8 - Slider time Slider time
The machine can be fitted with a device that automatically lifts the
drink dispensing compartment door.
With this function it is possible to define whether the device is
present in the machine and how long (programmable between 0
and 300 t/s, 70 by default) the slider is to be kept lifted.
The programmed duration controls also a lighting lamp inside the
dispensing compartment if the cup sensor is not fitted.

2.3.9
2.3.9 - SET CUP SETTLING Cup settling time
This function is used for setting the delay time in stopping the cup
column rotation in order to compensate any inertia due to the cup
type.

2.3.A
2.3.A - LAVAGGIO MOK-CAP Washing Mokaccino - Cappuccino
(Function active only in some models)
When activating this function a small amount of hot water is dis-
pensed into the milk mixer after two hours from a mokaccino or
cappuccino selection.

P2935EN00 10 - 2007
20
 TECHNICIAN Menu

2.3.B
2.3.B -EN. WASH BUTTON Enabling the wash button
With this function it is possible to enable the operation of the mixer
wash button.
Normally the button is disabled.

2.3.C
2.3.B - LAV. MIXER AUTO. Automatic mixer wash
It is possible to set the time when performing an automatic mixer
wash cycle. When setting the time to 24.00 the function is disabled
(default).

2.3.D
2.3.C - DEC. CYCLE Decaffeinated cycle
For the purpose of improving the appearance of the drink the
lyophilised instant product powder (if present) is dispensed before
dispensing water into the mixer.

2.3.E
2.3.E - PREGRINDING Pre-grinding

This function is used for enabling/disabling the grinding of coffee for

the next selection. This permits the reduction of dispensing time for
a coffee selection. The function is disabled by default.

2.3.F
2.3.F - Brewing time Brewing time (fresh-brew tea)
This function (enabled only in fresh-brew tea models) permits open-
ing of the tea dispensing solenoid valve for a length of time, set in
tenths of a second, and delivering of a small amount of water onto
the product in order to dampen it before the actual brewing cycle.

P2935EN00 10 - 2007
21
 TECHNICIAN Menu

2.4
2.4 - DISPLAY Display

2.4.1
2.4.1 - LANGUAGE Language
With this function it is possible to select the language used for surf-
ing within the programming menus and while in normal vending
mode. The list of available languages is indicated in the dose table.

2.4.2
2.4.2 - PROMOT. MESSAGE Promotional message

2.4.2.1
2.4.2.1 - EN. PROM. MESS. Enabling the promotional message
This function is used for enabling or disabling a promotional mes-
sage appearing on the display during the machine normal vending
mode.

2.4.2.2
2.4.2.2 - SET PROM. MESS Setting the promotional message
This function is used for writing the 4-line promotional message; by
pressing the confirm button “�” the first character starts blinking;
this can then be changed using the “�” and “�” buttons, scrolling
through the available characters.
Once the message is completed, it can be stored by pressing button
“�”.

2.4.3
2.4.3 - Enable pers. strings Enabling the personalised strings
This function is used for enabling the vending machine to receive,
through the Flash tool, some personalised strings visible on the
display during the normal machine vending mode.

P2935EN00 10 - 2007
22
 TECHNICIAN Menu

2.5
2.5 - PRE-SELECTIONS Pre-selections
This function is used for setting the pre-selections present in this
model, enabling or disabling the pre-selection for a certain selec-
tion, changing dose and price.
An example for the first pre-selection is indicated below; the opera-
tions to be carried out are identical for each selection.

2.5.1
2.5.1 - NO CUP without cup

This pre-selection is used for dispensing the selected product and

excluding the dispensing of the cup.

Enabling the selection

2.5.1.1 - SELECTION ENABL. Press the confirm button to select the selection button for which the
pre-selection is to be enabled.

2.5.1.2
2.5.1.2 - DOSE VARIATION Changing the dose
This function is used for changing the percentage of product dis-
pensed with the pre-selection (function valid only for some pre-
selections).

2.5.1.3
2.5.1.3 - PRICE VARIATION Changing the price
This function is used for assigning a discount or overprice to the
selection set with the pre-selection.

2.5.1.4
2.5.1.4 - STATO PRESELEZ. Pre-selection status
This function is used for setting the option of selecting the pre-
selection:
ON Enabled
OFF Disabled

2.5.2
2.5.2 - EXTRA SUGAR Extra Sugar
This pre-selection is used for dispensing the maximum dose of
sugar set together with the drink.

2.5.3
2.5.3 - SUGAR Sugar
This pre-selection is used for increasing or decreasing in a cyclical
manner the amount of sugar to be dispensed.

2.5.4
2.5.4 - SUGAR - Sugar -
This pre-selection is used for decreasing by
a modifiable dose the amount of sugar to be
dispensed.

P2935EN00 10 - 2007
23
 TECHNICIAN Menu

2.5.5
2.5.5 - SUGAR + Sugar +
This pre-selection is used for decreasing by a modifiable dose the
amount of sugar to be dispensed.

2.5.6
2.5.6 - WATER + Water +
This pre-selection is used for increasing by a modifiable amount the
water in the coffee or tea based selections.

2.5.7
2.5.7 - WATER - Water -
This pre-selection is used for decreasing by a modifiable amount
the water in the coffee or tea based selections.

2.5.8
2.5.8 - Powder + Powder +
This pre-selection is used for increasing the powder dose (coffee or
tea only) by a modifiable amount in the selections based on these
products.

2.5.9
2.5.9 - Powder - Powder -
This pre-selection is used for decreasing the powder dose (coffee
or tea only) by a modifiable amount in the selections based on these
products.

2.5.A
2.5.A - Coffee powder dose Coffee powder dose
This pre-selection is used for making a coffee-based selection with
the second type of available coffee (if present).

2.5.b
2.5.B - EXTRA MILK Extra Milk
This pre-selection is used for increasing by a modifiable amount the
milk dose (powder only) in the milk-based selections.

2.5.c
2.5.C - JUG + Jug +
Pre-selection not available in these models.

2.5.d
2.5.D - JUG - Jug -
Pre-selection not available in these models.

2.5.e
2.5.E - MOKKA Mokka
This pre-selection is used for decreasing by a modifiable amount
the water dose in the coffee selections for the
purpose of obtaining a “mokka” type drink.

P2935EN00 10 - 2007
24
 TECHNICIAN Menu

2.6
2.6 - - MISCELLANEOUS Miscellaneous

2.6.1
2.6.1 - JUG FACILITIES Jug facilities
This function is used for setting a programmable number (1 to 9; 5
by default) of consecutive selections to fill a jug.

2.6.2
2.6.2 - PASSWORD Password
This function is used for setting a password for accessing the
“Technician menu” mode.

2.6.2.1
2.6.2.1 - SET PASSWORD Setting the password
Enter a 5-digit numeric code to be set as the password.

2.6.2.2
2.6.2.2 - ENABLE PASSWORD Enabling the password

This function is used for enabling or disabling the password request

when accessing the “Technician menu” mode (disabled by default).

2.6.3
2.6.3 - ENABLE FILL MENU Enabling the Filler menu
This function is used for determining which of the “Filler menu”
functions are to be left active and which are to be disabled. The
reference numbers of the menus do not change even if some are
disabled.

2.6.4
2.6.4 - ENERGY SAVING Energy saving
This function is used for saving electric power when the machine is
not in use.

2.6.4.1
2.6.4.1 - SET ENER. SAVING Setting the energy saving

This function is used for enabling or disabling the automatic switch-

off of the vending machine boiler during the time when it is believed
the machine would not be used.

P2935EN00 10 - 2007
25
 TECHNICIAN Menu

2.6.4.2
2.6.4.2 - PARAM. EN.SAVING Energy saving parameters
This function is used for setting the days of the week (1 Monday,
2 Tuesday, 3 Wednesday, etc.) and the time bands (band 1 and 2)
when the boiler is to be switched off for energy saving.

2.6.5
2.6.5 - LAV. POS. UGELLI Position of spouts for washing
This function is used for setting the position of the spout assembly
during their wash cycle. There are 2 possible options::
- IN (standby position inside the machine)
- OUT (dispensing position).

2.6.6
2.6.6 - espresso unit Espresso Unit
This function is used for setting the standby position of the Z3000
espresso unit.
- OPEN brewing chamber open;
- CLOSED brewing chamber closed.
By default the position is set to OPEN.

2.6.7
2.6.7 - AUT.Unit wash Automatic unit wash
This function is used for setting the daily unit wash of the espresso
unit by setting the time when it is to be performed. If setting the time
to 00.00 the function is disabled.

2.6.8
2.6.8 - FAN CONTROL Exhauster control
This function is used for setting the continuous operation of the
exhauster fans for instant products:
- ON fans always on;
- OFF fans on only during dispensing and for the following 30
seconds.

2.6.9
2.6.9 - unit heating Espresso unit heating
This function is used for setting the espresso coffee based selection
for which the brewer unit heating must be enabled, permitting the
dispensing of hot water in the brewer unit before brewing the coffee.

2.6.A
2.6.A - unit heating time Espresso unit heating time
This function is used for setting the length of time from the last es-
presso coffee selection after which the brewer unit heating must be
performed (30 minutes by default).

P2935EN00 10 - 2007
26
 TECHNICIAN Menu

3
3 - STATISTICS Statistics

3.1
3.1 - ELECTRIC COUNTER Electronic counter

3.1.1
3.1.1 - DIS. COUNTERS Displaying the selection counters
This function is used for displaying the total number of selections
dispensed by the vending machine.

3.1.2
3.1.2 - RESET COUNTER Resetting the counters at power-on
This function is used for resetting the general selection counter.

3.2
3.2 - DISPLAY STATS. Displaying the statistics

3.2.1
3.2.1 - DIS. SEL. COUNT. Displaying the selection counters

3.2.1.1
3.2.1.1 - DIS. SIN. COUNT. Displaying the single counters
This function is used for displaying the counters regarding each
selection, divided by price band (0, 1, 2, 3, 4, Free, Test)

3.2.1.2
3.2.1.2 - DIS. TOT. COUNT. Displaying the total counters
This function is used for displaying the total counters regarding each
selection..

3.2.1.3
3.2.1.3 - DIS. SEL. COUNT. Displaying the selection counters in normal vending - maintenance
This function is used for displaying the total counters regarding the
selections made while in normal vending mode and maintenance
mode.

P2935EN00 10 - 2007
27
 TECHNICIAN Menu

3.2.2
3.2.2 - DIS. BAND COUNT. Displaying the time band counters
When selecting the desired price band (0, 1, 2, 3, 4, Free, Test), the
total number of selections made for that price band is displayed.

3.2.3
3.2.3 - DIS. DISC. SEL. Displaying the discount counters
This function is used for displaying the total amount of discounts
and overprice accumulated for the dispensed selections.

3.2.4
3.2.4 - DIS. FAIL.COUNT. Displaying the failure counters
This function is used for displaying the number of times each pos-
sible failure occurred in the vending machine.

3.2.5
3.2.5 - DIS. C MECH DATA Displaying the coin mechanism data

3.2.5.1
3.2.5.1 - DIS. AUDIT DATA Displaying the audit data
This function is used for displaying the number of coins inserted in
the vending machine, differentiated by the type of coin.

3.2.5.2
3.2.5.2 - DIS. CASH COUNT. Displaying the cashed amount
This function is used for displaying the value of:
- Total cashed
- Total sold
- Total cashed by credit

P2935EN00 10 - 2007
28
 TECHNICIAN Menu

3.3
3.3 - DEL. STATISTICS Deleting the statistics

3.3.1
3.3.1 - DELETE PARTIAL Partial delete

3.3.1.1
3.3.1.1 - DELETE SE. COUNT Deleting the selection counters
When confirming this function, the counters regarding the different
selections are deleted.

3.3.1.2
3.3.1.2 - DEL. DISC. COUNT Deleting the discount counters
When confirming this function, the counters regarding discounts
and overprice are deleted.

3.3.1.3
3.3.1.3 - DEL. FAIL. COUNT Deleting the failure counters
When confirming this function, the counters regarding the different
failure are deleted.

3.3.1.4
3.3.1.4 - DEL. C MECH DATA Deleting the coin mechanism data
When confirming this function, the counters regarding the coin
mechanism data are deleted.

3.3.2
3.3.2 - DELETE TOTAL Total delete
When confirming this function, all statistics are deleted.

P2935EN00 10 - 2007
29
 TECHNICIAN Menu

3.4
3.4 - DIS. REL. STATS. Displaying the relative statistics

3.4.1
3.4.1 - DIS. SEL. COUNT. Displaying the selection counters

3.4.1.1
3.4.1.1 - DIS. SIN. COUNT. Displaying the single counters
This function is used for displaying the counters regarding each
selection, divided by price band (0, 1, 2, 3, 4, Free, Test).

3.4.1.2
3.4.1.2 - DIS. TOT. COUNT. Displaying the total counters
This function is used for displaying the total counters regarding each
selection.

3.4.1.3
3.4.1.3 - DIS. SEL. COUNT. Displaying the selection counters in normal vending - maintenance
This function is used for displaying the total counters regarding the
selections made while in normal vending mode and maintenance
mode.

3.4.2
3.4.2 - DIS. BAND COUNT. Displaying the time band counters
When selecting the desired price band (0, 1, 2, 3, 4, Free, Test), the
total number of selections made for that price band is displayed.

3.4.3
3.4.3 - DIS. DISC. SEL. Displaying the discount counters
This function is used for displaying the total amount of discounts
and overprice accumulated for the dispensed selections.

3.4.4
3.4.4 - DIS. FAIL.COUNT. Displaying the failure counters
This function is used for displaying the number of times each pos-
sible failure occurred in the vending machine.

P2935EN00 10 - 2007
30
 TECHNICIAN Menu

3.4.5
3.4.5 - DIS. C MECH DATA Displaying the coin mechanism data

3.4.5.1
3.4.5.1 - DIS. AUDIT DATA Displaying the audit data
This function is used for displaying the number of coins inserted in
the vending machine, differentiated by the type of coin.

3.4.5.2
3.4.5.2 - DIS. CASH COUNT. Displaying the cashed amount
This function is used for displaying the value of:
- Total cashed
- Total sold
- Total cashed by credit

P2935EN00 10 - 2007
31
 TECHNICIAN Menu

3.5
3.5 - DEL. REL. STATS Deleting the relative statistics

3.5.1
3.5.1 - DELETE PARTIAL Partial delete

3.5.1.1
3.5.1.1 - DELETE SE. COUNT. Deleting the selection counters
When confirming this function, the counters regarding the different
selections are deleted.

3.5.1.2
3.5.1.2 - DEL. DISC. COUNT Deleting the discount counters
When confirming this function, the counters regarding discounts
and overprice are deleted.

3.5.1.3
3.5.1.3 - DEL. FAIL. COUNT Deleting the failure counters
When confirming this function, the counters regarding the different
failure are deleted.

3.5.1.4
3.5.1.4 - DEL. C MECH DATA Deleting the coin mechanism data
When confirming this function, the counters regarding the coin
mechanism data are deleted.

3.5.2
3.5.2 - DELETE TOTAL Total delete
When confirming this function, all relative statistics are deleted.

3.6
3.6 - EN. CNT AT START Enabling the counters at power-on
By enabling this function, it is possible to display the total counters
when the machine is switched on.

P2935EN00 10 - 2007
32
 TECHNICIAN Menu

3.7
3.7 - PRINT STATISTICS Printing the Statistics

3.7.1
3.7.1 - PARTIAL PRINTOUT Partial printout

3.7.1.1
3.7.1.1 - PRINT SEL. COUNT. Printing the selection counters
When confirming this function, the counters regarding the different
selections are printed.

3.7.1.2
3.7.1.2 - PRINT BAND COUNT Printing the time band counters
When confirming this function, the counters regarding the different
time bands are printed.

3.7.1.3
3.7.1.3 - PRINT DISC COUNT Printing the discount counters
When confirming this function, the counters regarding discounts
and overprice are printed.

3.7.1.4
3.7.1.4 - PRINT FAIL COUNT Printing the failure counters
When confirming this function, the counters regarding the different
failure are printed.

3.7.1.5
3.7.1.5 - PRNT C MECH DATA Printing the coin mechanism data
When confirming this function, the counters regarding the coin
mechanism data are printed.

3.7.2
3.7.2 - TOTAL PRINTOUT Total printout
When confirming this function, all statistics are printed.

P2935EN00 10 - 2007
33
 TECHNICIAN Menu

3.8
3.8 - PRINT REL. STATS. Printing the relative statistics

3.8.1
3.8.1 - PARTIAL PRINTOUT Partial printout

3.8.1.1
3.8.1.1 - PRINT SEL. COUNT Printing the selection counters
When confirming this function, the relative counters regarding the
different selections are printed.

3.8.1.2
3.8.1.2 - PRINT BAND COUNT Printing the time band counters
When confirming this function, the relative counters regarding the
different time bands are printed.

3.8.1.3
3.8.1.3 - PRINT DISC COUNT Printing the discount counters
When confirming this function, the relative counters regarding dis-
counts and overprice are printed.

3.8.1.4
3.8.1.4 - PRINT FAIL COUNT Printing the failure counters
When confirming this function, the relative counters regarding fail-
ures are printed.

3.8.1.5
3.8.1.5 - PRNT C MECH DATA Printing the coin mechanism data
When confirming this function, the relative counters regarding the
coin mechanism data are printed.

3.8.2
3.8.2 - TOTAL PRINTOUT Total printout
When confirming this function, all relative statistics are printed.

P2935EN00 10 - 2007
34
 TECHNICIAN Menu

4.
4 - TEST Test

4.1
4.1 - TEST DISPENSING Test dispensing

4.1.1
4.1.1 - COMP. DISPENSING Complete dispensing
With this function it is possible to obtain, with the door open
and without inserting any money, complete dispensing for each
selection.

4.1.2
4.1.2 - WATER ONLY Dispensing water only
With this function it is possible to dispense, with the door open
and without inserting any money, only the water doses for each
selection.

4.1.3
4.1.3 - POWDER ONLY Dispensing powder only
With this function it is possible to dispense, with the door open
and without inserting any money, only the powder doses for each
selection.

4.1.4
4.1.4 - NO ACCESSORIES without accessories

With this function it is possible to dispense, with the door open and
without inserting any money, only the water and powder doses for
each selection, without any cup and stirrer.

4.1.5
4.1.5 - ACCESSORIES ONLY accessories only

With this function it is possible to dispense, with the door open

and without inserting any money, only the accessories for each
selection.

P2935EN00 10 - 2007
35
 TECHNICIAN Menu

4.2
4.2 - SPEC. FUNCTIONS Special functions

4.2.1
4.2.1 - UNIT ROTATION Unit rotation
This function is used for operating the espresso brewer unit (if
fitted).

4.2.2
4.2.2 - RELEASE DOSE Releasing a dose
This function is used for starting the grinder e release a coffee dose.

4.2.3
4.2.3 - EMPTY BOILER Emptying the boiler
This function is used for opening a solenoid valve to allow the intake
of air in the event of emptying the boiler for maintenance.

4.2.4
4.2.4 - MANUAL INSTALL. Manual installation
This function is used for manually installing the boilers and filling the
water system.

P2935EN00 10 - 2007
36
 TECHNICIAN Menu

4.3
4.3 - AUTOTEST Autotest
This function allows testing, in a semiautomatic way, of the main ma-
chine components. When pressing the confirm button, the message
"AUTOTEST" will be start blinking.
It is possible to cancel each operation and go to the next one by
pressing the exit button, but confirming with the confirm button to
start the autotest routine. Some checks occur automatically, others
need the manual operation of the monitored component.
In a sequence:
- Control steam exhaust fan functioning for 2 seconds
- The doser units are activated for 2 seconds
- The mixers are activated for 2 seconds
- A cup is released
- A stirrer is released
- The dispensing spouts are operated/repositioned
- Rotation of the brewer unit
- Wash button test
- Waste container switch; the machine awaits until the waste con-
tainer micro-switch is manually operated
- Test led; control the functioning of the push-button lighting
- Switching on of the dispensing compartment lamp (if fitted)
- Push-button panel test; the machine will display the number of the
button which must be pressed and awaits the actuation before going
to the next button
- Boiler temperature probe functioning test
- Buzzer functioning test
- Coin mechanism functioning test

P2935EN00 10 - 2007
37
 TECHNICIAN Menu

5
5 - MISCELLANEOUS Miscellaneous

5.1
5.1 - MACHINE INFO Vending machine information

5.1.1
5.1.1 - INSTALL. DATE Installation date
This function is used for storing the current date of system as instal-
lation date of the vending machine. This date will be indicated on the
statistics printout.

5.1.2
5.1.2 - PROG. MACH. CODE Setting the machine code
This function is used for changing the 8-digit numeric code identify-
ing the machine (set to 0 by default).

5.1.3
5.1.3 - PROG. OPER. CODE Setting the operator code
This function is used for changing the 6-digit numeric code identify-
ing the group of machines (set to 0 by default).

P2935EN00 10 - 2007
38
 TECHNICIAN Menu

5.2
5.2 - INITIALIZ. DB Initialising the data-base
This function is used for “initialising” the machine, resetting all data
to default values. This function should be used if there is a memory
data error or when the software is replaced. Except for the general
electronic counter, all statistical data is reset.
When confirming this function some parameter settings are request-
ed, and namely:
- COUNTRY
Intended as type of basic doses for the different selections. The
available “countries” vary according to the models.
- LAYOUT
A number of Button/Selection combinations to choose from is
provided for each dose type model (the combinations available for
each layout are indicated in the dose selection table supplied with
the machine).
- TANK
Defining whether the water supply is:
0 - from the mains
1 - from an internal tank
2 - from two internal tanks .

P2935EN00 10 - 2007
39
 TECHNICIAN Menu

5.3
5.3 - EVADTS Evadts
The EVADTS (European Vending Association Data Transfer System)
communication protocol has 2 codes for identifying the machine
and for recognising the data transfer terminal.

5.3.1
5.3.1 - PASS.CODE Pass code
It is a four-digit alphanumeric code (0-9; A-F) that must be the same
as the one in the data transfer terminal to allow its identification.
When pressing the confirm button the code is displayed as “0000”
regardless of the actual value; then by pressing the confirm button
the first digit will start blinking.
Using the scrolling buttons, its value can be changed (during the
change operation the value becomes visible).
Repeat this operation for the 4 digits, after which the value is stored
and the display will indicate “0000” again.

5.3.2
5.3.2 - SECURITY CODE Security code
It is a further alphanumeric code for reciprocal recognition between
machine and EVADTS terminal.
Programming works as in the “Pass Code”.

5.3.3
5.3.3 - CONNECTION Connection
This function places the machine in wait mode for connection to
retrieve data.

5.3.4
5.3.4 - PROTOC. EVADTS Protocol Evadts
This function is used for selecting the communication protocol to
be used (DDCMP or DEX/UCS) for communication with the data
acquisition device.

5.3.5
5.3.5 - MODE Mode
This function is used for selecting the communication interface to be
used with the data transfer terminal.
- “IrDA” or “RS232”: for communication with data acquisition devices
- “ALWAYS EVADTS”: for communication with data acquisition and
transmission (e.g. telemetry).

5.3.6
5.3.6 - TYPE Type
This function is used for setting the communication speed to be
used, between:
- “ENHANCED”: the communication speed is set automatically at
the speed of the slowest device
- “STANDARD 9600bps”: the communication
speed is set to 9600bps.

P2935EN00 10 - 2007
40
 TECHNICIAN Menu

5.4
5.4 - UPKEY Up key

5.4.1
5.4.1 - SETUP MANAGEMENT Setup control

5.4.1.1
5.4.1.1 - UPKEY->MACHINE Up-Key -> vending machine
When confirming this function after inserting the Up-Key in the
special port located on the C.P.U. board, it will be possible to select
the setup file from the list shown on the display using the scrolling
buttons, then when confirming with the confirm button the selected
setup will be loaded in the vending machine.
5.4.1.2
5.4.1.2 - MACHINE->UPKEY Vending machine -> Up-Key
When confirming this function after inserting the Up-Key in the
special port located on the C.P.U. board, it will be possible to save
the setup file to the Up-Key with the configuration present in that
moment in the vending machine, indicating the name to be assigned
to the file.
5.4.1.3
5.4.1.3 - DELETE Delete
This function is used for deleting one by one the setup files present
in the inserted Up-Key.

5.4.1.4
5.4.1.4 - DELETE ALL Delete all
This function is used for deleting all the setup files present in the
inserted Up-Key.

5.4.2
5.4.2 - AUDIT MANAGEMENT Statistics management

5.4.2.1
Vending machine -> Up-Key
5.4.2.1 - MACHINE->UPKEY
When confirming this function after inserting the Up-Key in the
special port located on the C.P.U. board, it will be possible to save
the statistics file to the Up-Key with all of the statistics files present
in that moment in the vending machine, indicating the name to be
assigned to the file
5.4.2.2
5.4.2.2 - DELETE Delete
This function is used for deleting one by one the statistics files
present in the inserted Up-Key.

5.4.2.3
5.4.2.3 - DELETE ALL Delete all
This function is used for deleting all the statistics files present in the
inserted Up-Key.

P2935EN00 10 - 2007
41
 TECHNICIAN Menu

5.4.3
5.4.3 - V.M. SELECTION Vending machine selection
This function is enabled only if the machine is installed in a bank
with one or more Minisnakky / Snakky / Snakky SL.
It is used for selecting the vending machine in the bank of machines
on which to operate with the Up-Key (Brio3 or Minisnakky or Snakky
o Snakky SL).

6
6 - GSM GSM
The control software can send, via GSM modem, a signal indicating
a machine failure or an “ending product” “pre-alarm”, after dis-
pensing a certain (programmable) number of selections of a given
product.

6.1
6.1 - GSM PIN CODE GSM Pin code
This function is used for programming the identification code that
will be sent to the GSM modem (optional) when switching the ma-
chine on.

6.2
6.2 - GSM PRE-ALARMS GSM pre-alarms

6.2.1
6.2.1 - PRE-ALARM THRESH Pre-alarms thresholds
This function is used for defining the number of pieces or grams of
powder for a given product, after which a “running-out” “pre-alarm” is
signalled via modem.

6.2.2
6.2.2 - RESET PRE-AL CNT Resetting the pre-alarm counters
With this function the counters that control the pre-alarms are reset.

6.3
6.3 - Bank number Bank number
The number in the bank of machines (1 to 7) that identifies the
machines that have the “slave GSM” function, therefore sending
data via the “master” machine modem .
The number 0 identifies the machine that is connected directly to
the modem, i.e. the “master GSM”..

P2935EN00 10 - 2007
42
 List of Failures

Water failure
If the air-break micro-switch is closed for more than one minute, the water inlet solenoid valve will remain ener-
gized until the water flow is restored.
If the machine is equipped with an internal water supply tank the pump will be switched off.
Waste container full
The espresso coffee based selections are disabled when reaching the number of used coffee doses that the
solid waste tray can hold.
Air-break
The machine is locked if after 10 selections the micro-switch has never signalled the lack of water.
No cups in the dispenser
When the empty cup column microswitch opens, the cup column shift motor is activated. If after one full turn
the microswitch is not closed the machine is placed out of service.
Spouts
If the spouts do not reach the dispensing position, the machine is placed out of service.
Impeller
The machine is locked in the event of failed computation of the volumetric counter (flow-meter) within a max.
given time.
Boiler
The machine will lock if after 20 minutes of heating from the machine start, or from the last selection, the in-
stant boiler fails to reach the operating temperature set with the function “Boiler temperature” of the Technician
Menu.
Machine control board
The machine will lock in the event of failed communication between C.P.U. board and machine control board.
Coin mechanism
The machine is locked if it receives a pulse longer than 2 seconds on a validator line or the communication
with the serial coin mechanism does not take place for more than 30 seconds (Executive) or 75 seconds
(BDV).
Coffee release
If after releasing the ground coffee dose the micro-switch of the coffee doser unit indicates the presence of
coffee in the dosing chamber, all coffee-based selections are disabled.
Coffee unit
Due to mechanical blocking of the coffee unit. The machine is not locked, but the espresso coffee-based se-
lections are disabled.
No coffee
If the coffee grinder speed exceeds the value of 1200 rpm for longer than 5 seconds the “no coffee” failure is
registered.
It is possible to enable this type of warning and disable the coffee-based selections in the function “Enable no
coffee” of the Technician Menu.
RAM data
One or more areas of the RAM contain wrong data which was corrected with the default values.
The machine will continue to function, but it would be advisable to initialise as soon as possible.
Cup release
This message can be visualized if the machine is equipped with the cup sensor (optional).
The machine will lock if:
- The cup sensor does not detect an object in the dispensing compartment after 2 attempts to dispense a cup.
- In the function of "Photocell" under the "Technical Menu", this type of failure has been set up as "lock/block".

P2935EN00 10 - 2007
43
 Coin Mechanism Settings

OFF
In the event of configuring the machine in a bank, this setting permits the control of 2 payment systems in-
stalled in 2 vending machines, so that when one payment system fails or no longer works, automatically the
other payment system becomes functional for the bank of machines.

Validators
When the “Validator Lines” function (line programming) of the “programming” menu is displayed, the value of
the 6 Validator coin lines, A to F, can be changed.

Executive
The following payments systems are available for the Executive system:
- Standard
- Price Holding
- Coges
- U-Key
- Sida

BDV
The BDV protocol menus are used for defining the following functions:
Type of vending
Setting the operating mode for multiple or single dispensing. With multiple dispensing, the change is not
automatically returned after a successful selection; however the credit is available for further selections. When
pressing the coin return button, the available credit is returned if its value is lower than the maximum change
value.
Change control
This function enables/disables the return of credit if no selections are made.
If enabled, this function allows the return of coins even if the first selection was not dispensed.
If however a selection fails for any reason, the change will be returned if requested.
Maximum credit
This function is used to define the maximum accepted credit.
Maximum change
It is possible to set a limit to the total amount of change returned by the coin mechanism when pressing the
coin return button or after a single dispensing serving.
Any credit exceeding the amount programmed with this function will be cashed.
Accepted coins
It is possible to define which, among the coins recognised by the validator, are to be accepted.
Check the label on the coin mechanism for the correct coin to value matching, indicating the position of the
coins.
Non accepted coins
This function programs the rejection of coins when in "exact amount" mode.
Check the label on the coin mechanism for the correct coin to value matching, indicating the position of the
coins.
Dispensing buttons
This function enables or not the buttons on the coin mechanism used to release the coins in the change return
tubes.

P2935EN00 10 - 2007
44
 Coin Mechanism Settings

Value of "exact amount"

This value defines the combination of empty coin tubes, setting the coin mechanism in "exact amount" mode.
The possible combinations of empty coin tubes are indicated below.
For greater simplicity, the combination is described with reference to tubes A, B and C, where tube A receives
the lower value coins and tube C the greater value coins.
0 = A or (B and C)
1 = A and B and C
2 = A and B only
3 = A and (B or C)
4 = A only
5 = A or B only (default)
6 = A or B or C
7 = A or B only
8 = A or C only
9 = B and C only
10 = B only
11 = B or C only
12 = C only
C.P.C. device
It dialogues with the coin mechanism if devices are installed or removed from the serial interface (C.P.C.-type
devices - the monitoring unit is always enabled by default).
Minimum level of tubes
It brings forward the "Insert exact amount" message for the user, by adding a number of coins between 0 and
15 to the programmed number of coins, to set the "full change tubes" status.
Free Vend VMC
Most payment systems with the BDV protocol control the free vend function.
However, there are some payment systems without such function.
In this case, if free selections are to be dispensed, free vending must be enabled with VMC (vending machine
control, enabled by default) and the price of the selections must be set to zero.

MDB
The MDB protocol menus are used for defining the following functions:
Type of vending
Setting the operating mode for multiple or single dispensing. With multiple dispensing, the change is not
automatically returned after a successful selection; however the credit is available for further selections. When
pressing the coin return button (if the function is enabled), the available credit is returned up to the maximum
change value.
Obligation to buy / Change control
This function enables/disables the operation of the coin return button before dispensing a product. After the
selection is made, the coin return button will resume its function.
Maximum credit
This function is used to define the maximum credit that can be accepted.
Maximum change
It is possible to set a limit to the total amount of change returned by the coin mechanism when pressing the
coin return button or after a single dispensing serving.
Any credit exceeding the amount programmed with this function will be cashed.
Accepted coins
It is possible to define which, among the coins recognised by the coin mechanism, are to be accepted when
the change tubes are full.
Check the coin mechanism configuration for the correct coin to value matching.
Returned coins
It is possible to define which, among the coins available in the tubes, are to be used for returning the change.
This parameter is active only with coin mechanisms that do not automatically control the choice of tube to be
used (Auto changer payout).
Check the coin mechanism configuration for the correct coin to value matching.

P2935EN00 10 - 2007
45
 Coin Mechanism Settings

Minimum level of tubes

This function is used for setting the number of coins (0 to 15) to determine the status of full change tubes and
the "Insert exact amount" message for the user.
Accepted bills
It is possible to define which, among the bills recognised by the reader, are to be accepted.
Check the reader configuration for the correct bill to value matching.
Accepted coins with "exact amount"
It is possible to define which, among the coins recognised by the coin mechanism, are to be accepted when
the machine is in the "exact amount" condition.
Check the coin mechanism configuration for the correct coin to value matching.
Accepted bills with "exact amount"
It is possible to define which, among the bills recognised by the accepter, are to be accepted when the ma-
chine is in the "exact amount" condition.
Check the accepter's configuration for the correct bill to value matching.
Cashless Private / Undefined Credit Control
This function is used for showing or not on the display the credit present in the cashless system, replacing it
with the string "-----". The same string is displayed also in the event where the credit of the cashless system is
not defined.
Overpay
Thus function is used for setting the management of credit excess.
Credit excess is a credit that cannot be returned to the user; for example in the event of failing to return the
change due to insufficient minimum level in the tubes.
If set as MAINTAINED any credit excess remains available to the user.
If set as CANCELLED, it permits to maintain the credit excess for a programmable time before cashing it.
Cash sale
This function is used for setting the management of messages for sales made with cash for statistical
purposes.
0 - The data is sent as per MDB protocol
1 - The sales data is sent by overriding to the cashless system 1
2 - The sales data is sent by overriding to the cashless system 2
Parallel Device
This function permits the use of a coin or bill validator in place of an MDB Changer (coins) or MDB Bill
Validator (banknotes).
The replaced MDB device, after resetting the machine, will no longer be used.
Exact change equation
This value defines the combination of empty coin tubes, setting the coin mechanism in "exact amount" mode.
The possible combinations of empty coin tubes are indicated below.
For greater simplicity, the combination is described with reference to tubes A, B and C, where tube A receives
the lower value coins and tube C the greater value coins.
0 = A or (B and C)
1 = A and B and C
2 = A and B only
3 = A and (B or C)
4 = A only
5 = A or B only (default)
6 = A or B or C
7 = A or B only
8 = A or C only
9 = B and C only
10 = B only
11 = B or C only
12 = C only

P2935EN00 10 - 2007
46
 Coin Mechanism Settings

Maximum cash credit

This function is used for setting the maximum credit that can have a key / cashless card to be acceted by the
system. If the key has a higher value, it will be rejected.
The value setting must be always greater or equal to the value set with the function "Maximum cash revalue";
in the event it were changed and become lower than such value, it will be set automatically to the same value
of the "Maximum cash revalue".
Maximum cash revalue
This function is used for settino the maximum credit that can be loaded in a cashless system.
This value cannot be greater than the value set with the function "Maximum cash credit".

P2935EN00 10 - 2007
47
The manufacturer reserves the right to modify, without prior notice, the characteristics of the equipment de-
scribed in this publication; he declines all responsibility for any inaccuracies due to printing and/or typing errors
herein contained.
The instructions, drawings, tables and information in general contained in this booklet are of a confidential
nature and may not be reproduced entirely or in part or be passed on to a third party without the prior written
authorisation of the manufacturer who retains itslusive ownership.