This document provides specifications for the design of studs and bolts, including material properties, member dimensions, loads, and calculations. Unit weights are given for concrete and steel. Maximum compressive and yield strengths are listed. Self weights and wind loads are specified for various slab and beam dimensions. Calculations are shown for beam reactions, column dimensions, moments and stresses, anchor bolt sizing, development lengths, weld and dowel capacities, and bearing stress. Diagrams illustrate the column cross section and combined stresses. The design is noted to require revision in certain areas.
This document provides specifications for the design of studs and bolts, including material properties, member dimensions, loads, and calculations. Unit weights are given for concrete and steel. Maximum compressive and yield strengths are listed. Self weights and wind loads are specified for various slab and beam dimensions. Calculations are shown for beam reactions, column dimensions, moments and stresses, anchor bolt sizing, development lengths, weld and dowel capacities, and bearing stress. Diagrams illustrate the column cross section and combined stresses. The design is noted to require revision in certain areas.
This document provides specifications for the design of studs and bolts, including material properties, member dimensions, loads, and calculations. Unit weights are given for concrete and steel. Maximum compressive and yield strengths are listed. Self weights and wind loads are specified for various slab and beam dimensions. Calculations are shown for beam reactions, column dimensions, moments and stresses, anchor bolt sizing, development lengths, weld and dowel capacities, and bearing stress. Diagrams illustrate the column cross section and combined stresses. The design is noted to require revision in certain areas.
This document provides specifications for the design of studs and bolts, including material properties, member dimensions, loads, and calculations. Unit weights are given for concrete and steel. Maximum compressive and yield strengths are listed. Self weights and wind loads are specified for various slab and beam dimensions. Calculations are shown for beam reactions, column dimensions, moments and stresses, anchor bolt sizing, development lengths, weld and dowel capacities, and bearing stress. Diagrams illustrate the column cross section and combined stresses. The design is noted to require revision in certain areas.
COLUMN D1 (long) 650 mm D2 (Short) 650 mm Width of Corbel 250 mm Tolerance 20 mm Column Length 14.7 m
Eccentricity to col centre 470 mm 0.47 m
Moment 129.631 KN-m
Case 1 Wind load on column 0.975 KN/m Bending moment 105.343875 KN-m Axial Load 155.26875 KN
Moment of Inertia I 14875520833 mm4
Section Modulus Z 45770833.33 mm3
Stresses due to moment
fca 2.302 N/mm2
Stress due to gravity load
fcb 0.368 N/mm2
COMBINED STRESSES y x Tension Side 1.934 N/mm2 1.934 0 Compression Side 2.67 N/mm2 -2.67 650
Tension at bolts on tension side of column
width under tension 273.045 mm Tensile force to be resisted Tu 171.622 KN
Diameter of Anchor Used 32 mm
Net S-Sec Area of threaded bolt 643.4 mm2
Tensile Capacity/Anchor 162.14 KN
No. of Anchors needed 1.06
No. of Anchors provided/side 3
USE 3 dia 32 anchors on each side
DESIGN OF STUD BOLT CONNECTION
1 DEVELOPMENT LENGTH Ψt 1 Ψe 1 λ 1
Ld 40 db Db used 32 mm Ld 1280
Splice Length 1664 mm
2 CAPACITY OF WELD CONNECTION
Weld b/w dowel & Plate
No. of stud bolt connection(s)
Load/Assembly KN
TRIAL No of welds Thickness mm Thickness of plate mm Effective throat thickness 0 mm Shear Capacity of Weld 0 N/mm
Max shear Capacity of plate 0 N
Allowable tensile capacity of weld KN
Allowable tensile capacity of dowel KN > 0
Weld B/W angle & base plate
Max Tensile force KN
TRIAL Thickness of weld mm Effective throat thickness 0 mm Shear capacity of dowel 0 N/mm Max shear capacity of plate 0 N Allowable tensile capacity of weld KN Allowable tensile capacity of Angle KN
Capacity of welded connection 0 >
4 DEVELOPMENT LENGTH OF HEADED DEFORMED BAR IN TENSION
ldt 13 db Dia of bar 25 mm ldt 325 mm < STUD BOLT CALCULATION
Max horizontal reaction KN
Area of Dowel used mm2 Allowable shear/dowel 0 KN/bar No. of dowels used Total Shear capcaity 0 KN > 0
Use g60 flowable grout f'c 60 Mpa
Max vertical reaction KN Bearing Area 422500 mm2 Bearing Stress 0 N/mm2
Allowable bearing stress 33.15 N/mm2 > 0
Axial compression from columns
max vertical reaction 0 KN Axial Capacity 11204.7 KN > 0 GN
