Scribd Logo
Upload

Welcome to Scribd!

  • 441 views

    DTC P0778 Pressure Control Solenoid "B" Electrical (Shift Solenoid Valve SL2)

    Uploaded by

    marsh2002
    This document provides information about a diagnostic trouble code (DTC) P0778 related to an automatic transmission. DTC P0778 indicates an open or short circuit in the shift solenoid valve SL2. The monitor checks for issues with solenoid valve SL2 by commanding shifts and checking the response from the hybrid control unit. If a fault is detected, the engine control module performs fail-safe operations and illuminates the malfunction indicator lamp. The inspection procedure checks the transmission wire, wire harness, and shift solenoid valve SL2 to diagnose the problem.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    DTC P0778 Pressure Control Solenoid "B" Electrical (Shift Solenoid Valve SL2)

    Uploaded by

    marsh2002
    441 views3 pages
    This document provides information about a diagnostic trouble code (DTC) P0778 related to an automatic transmission. DTC P0778 indicates an open or short circuit in the shift solenoid valve SL2. The monitor checks for issues with solenoid valve SL2 by commanding shifts and checking the response from the hybrid control unit. If a fault is detected, the engine control module performs fail-safe operations and illuminates the malfunction indicator lamp. The inspection procedure checks the transmission wire, wire harness, and shift solenoid valve SL2 to diagnose the problem.

    Original Description:

    obd2 diag

    Original Title

    0270023

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides information about a diagnostic trouble code (DTC) P0778 related to an automatic transmission. DTC P0778 indicates an open or short circuit in the shift solenoid valve SL2. The monitor checks for issues with solenoid valve SL2 by commanding shifts and checking the response from the hybrid control unit. If a fault is detected, the engine control module performs fail-safe operations and illuminates the malfunction indicator lamp. The inspection procedure checks the transmission wire, wire harness, and shift solenoid valve SL2 to diagnose the problem.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    441 views3 pages

    DTC P0778 Pressure Control Solenoid "B" Electrical (Shift Solenoid Valve SL2)

    Uploaded by

    marsh2002
    This document provides information about a diagnostic trouble code (DTC) P0778 related to an automatic transmission. DTC P0778 indicates an open or short circuit in the shift solenoid valve SL2. The monitor checks for issues with solenoid valve SL2 by commanding shifts and checking the response from the hybrid control unit. If a fault is detected, the engine control module performs fail-safe operations and illuminates the malfunction indicator lamp. The inspection procedure checks the transmission wire, wire harness, and shift solenoid valve SL2 to diagnose the problem.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 3

    U151E AUTOMATIC TRANSAXLE – AUTOMATIC TRANSAXLE SYSTEM AX–97

    Pressure Control Solenoid "B" Electrical (Shift


    DTC P0778
    Solenoid Valve SL2)
    DESCRIPTION
    Shifting from 1st to 5th is performed in combination with the ON and OFF operation of the shift solenoid
    valves SL1, SL2, SL3, S4 and SR, which are controlled by the ECM. If an open or short circuit occurs in
    any of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the
    vehicle to be operated safely (see page AX-35).
    DTC No. DTC Detection Condition Trouble Area
    P0778 ECM checks for an open or short circuit in • Open or short in shift solenoid valve SL2
    shift solenoid valves SL2 (1 trip detection circuit
    logic) • Shift solenoid valve SL2
    Hybrid IC for solenoid indicates fail • ECM

    MONITOR DESCRIPTION
    The ECM commands gear shifts by turning the shift solenoid valves ON/OFF. When there is an open or
    short circuit in any shift solenoid valve circuit, the ECM detects the problem and illuminates the MIL and
    stores the DTC. And the ECM performs the fail-safe function and turns the other normal shift solenoid
    valves ON/OFF. In case of an open or short circuit, the ECM stops sending current to the circuit (see page
    AX-35).

    MONITOR STRATEGY
    Related DTCs P0778: Shift solenoid valve SL2/Range check
    Required sensors/Components Shift solenoid valve SL2
    Frequency of operation Continuous
    Duration 1 sec.
    MIL operation Immediate
    Sequence of operation None

    TYPICAL ENABLING CONDITIONS


    The monitor will run whenever this DTC is not present. None
    Battery voltage 11 V or more
    Starter OFF
    Ignition switch ON
    Solenoid current cut status Not cut
    CPU commanded duty 19% or more

    TYPICAL MALFUNCTION THRESHOLDS


    Solenoid status from MIC Fail

    COMPONENT OPERATING RANGE


    Output signal duty Less than 100%

    AX
    AX–98 U151E AUTOMATIC TRANSAXLE – AUTOMATIC TRANSAXLE SYSTEM

    WIRING DIAGRAM

    Shift Solenoid Valve SL2


    (ECT Solenoid Valve)
    ECM

    SL2+
    SL2+

    SL2-
    SL2-

    C119177E04

    INSPECTION PROCEDURE

    1 INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL2)

    (a) Disconnect the B32 wire connector.


    Wire Harness Side (b) Measure the resistance of the transmission wire.
    Standard resistance
    Tester Connection Condition Specified Condition
    SL2+ 5 (SL2+) - 12 (SL2-) 20°C (68°F) 5.0 to 5.6 Ω
    5 (SL2+) - Body ground 20°C (68°F) 1 MΩ or higher
    12 (SL2-) - Body ground 20°C (68°F) 1 MΩ or higher
    6 5 4 3 2 1
    13 12 11 10 9 8 7
    NG Go to step 3

    SL2-

    C136383E04

    OK

    AX
    U151E AUTOMATIC TRANSAXLE – AUTOMATIC TRANSAXLE SYSTEM AX–99

    2 CHECK WIRE HARNESS (TRANSMISSION WIRE - ECM)

    (a) Disconnect the B30 ECM connector.


    Wire Harness Side (b) Measure the resistance of the wire harness side
    connector.
    Standard resistance
    B30
    SL2+ SL2- Tester Connection Condition Specified Condition
    B30-12 (SL2+) - B30-13 20°C (68°F) 5.0 to 5.6 Ω
    (SL2-)
    B30-12 (SL2+) - Body 20°C (68°F) 1 MΩ or higher
    ground
    B30-13 (SL2-) - Body 20°C (68°F) 1 MΩ or higher
    ground

    NG REPAIR OR REPLACE HARNESS AND


    CONNECTOR
    A107892E72

    OK

    REPLACE ECM

    3 INSPECT SHIFT SOLENOID VALVE SL2

    (a) Remove the shift solenoid valve SL2.


    (b) Measure the resistance of the solenoid valve.
    1 2 Standard resistance:
    5.0 to 5.6 Ω at 20°C (68°F)
    (c) Connect the battery's positive (+) lead with a 21 W bulb
    to terminal 2 and the negative (-) lead to terminal 1 of the
    solenoid valve connector. Then check that the valve
    moves and makes an operating noise.
    OK:
    Valve moves and makes operating noise.
    NG REPLACE SHIFT SOLENOID VALVE SL2
    1 2

    (-) (+)

    C140848E01

    OK
    AX
    REPAIR OR REPLACE TRANSMISSION WIRE

    You might also like