International Journal of Metallurgical &

Materials Science and Engineering (IJMMSE)

ISSN(P): 2278-2516; ISSN(E): 2278-2524
Vol. 7, Issue 4, Dec 2017, 1-12
© TJPRC Pvt. Ltd.

EFFECT OF CARBURIZATION, ON THE MECHANICAL PROPERTIES OF

EN-8 STEEL IN DIFFERENT QUENCHING MEDIUM, AT

DIFFERENT QUENCHING TIME INTERVALS.

BSR VENU MADHAV, ABDUL AHAD MOHIUDDIN & MOHAMMED ATIFUDDIN

Department of Mechanical Engineering, Chaitanya Bharathi Institute of Technology, Hyderabad, India
ABSTRACT

EN-8 is widely used for many general engineering applications. Typical applications include shafts, studs,
bolts, connecting rods, screws, rollers. The Main Purpose of the Paper is to study the effect of heat treatment of
[1]
carburizing specimens of EN-8(medium carbon steel) by varying two parameter i.e. quenching time and quenching
medium. The carburization process is carried out for 8 hours at a constant temperature of 940°C followed by quenching
with different media like air, water and oil for various quenching times i.e. 60, 70 and 80 mins. The specimens so
obtained are subjected to tests, for determination of tensile strength, Hardness and case depth. The results of these tests
show that, as quenching time increases, there is an improvement in mechanical properties like tensile strength and are

Original Article
more for, water-quenched and least for air-quenched steels. Oil-quenched show intermediate values. From the
experimentation, it is also clear that, as the depth of the carbon layer increases, hardness and tensile strength are also
increasing. The experimental results are also supported by microstructure study, which show the formation of marten
site, that causes improvement in hardness and tensile strength.

KEYWORDS: Medium Carbon Steels, EN-8, Carburization, Quenching Medium, Quenching Time, Hardness, Tensile
Strength, Case depth & Microstructures

Received: Sep 30, 2017; Accepted: Oct 18, 2017; Published: Nov 04, 2017; Paper Id.: IJMMSEDEC20171

INTRODUCTION

Carburization provides a gradual change in carbon content volume from the surface to the core of a given
steel sample, resulting in a gradual alteration of the mechanical and wear properties. The heat treatment and
carburization enhances the mechanical properties. Carburizing is the addition of the carbon to the surface of the
low, medium carbon steels at the temperatures generally between 850°C and 950°C, at which austenite is in stable
crystal structure. Hardening is accomplished when the high-carbon surface layer is quenched to form martensite so
that, a high carbon martensite case with good wear and fatigue resistance is superimposed on a tough, low-carbon
steel core. Carburizing Steels for case hardening usually have base-carbon contents of about 0.2% with carbon
content of the carburized layer generally being controlled between 0.8% - 1%C. However, Surface carbon is often
limited to 0.9% because high carbon content can result in retained Austenite and brittle Martensite, which
destabilizes the overall mechanical strength of the steel. In Order to achieve better Mechanical Properties in the
Medium Carbon Steels (0.3%-0.6%C), the carbon content is increased by subjecting to a process called
Hardening.

www.tjprc.org [email protected]
2 BSR Venu Madhav, Abdul Ahad Mohiuddin & Mohammed Atifuddin

CASE HARDENING

Case Hardening is a simple method of hardening steel. Carbon is added to the outer surface of the steel, to a depth
of approximately 0.03mm. This Hardening process includes a wide variety of techniques used to improve the mechanical
properties and wear resistance of parts without affecting the softer, tough interior of the part.

Carburization [4]

It is a kind of case hardening where the chemistry of the surface needs to be changed by adding carbon and
nitrogen to get hard martensite. This Category of treatment is called Chemical Heat Treatment and it involves nitriding,
carburising, carbonitriding, cyaniding. Carburization, is simply defined as the addition of carbon to the surface of
low/medium carbon steel, at a temperature between 850-950°C. It consists of enrichment of surface layers of medium
carbon steel (0.3% - 0.6% C) to (0.8 – 1%), Carbon Content. By this way, the good wear and fatigue resistance is
superimposed, on a tough medium carbon steel core. Usually, these steels have base carbon content as 0.35%, with the
carbon content at the carburized layer, generally being controlled at 0.8-1% C. However, the carbon content is generally
limited to 0.9% C, as to high carbon can result in retained austenite and brittle martensite [9].

OBJECTIVE

The Main Objective is, to improve the mechanical Properties of EN-8 medium carbon steel, by using acetone gas
as a carburizer [2] and less energy consuming carburization technique. In this connection, the following steps were aimed to
be carried out.

• Carburization of EN-8 samples under various conditions of carburization, by using less energy consuming as
techniques.

• Tempering of these carburized EN-8 samples at a definite temperature, for a particular period of time.

• Study of microstructure of the hardened steel samples.

• Determination of Mechanical properties, like Hardness and tensile strength of the carburized and tempered EN-8
Samples.

• Study of Carbon case depth of these carburized and tempered EN-8 samples.

• Analysis of the results obtained.

Mechanical Properties Studied

• Microstructure

• Case depth

• Tensile Strength

• Hardness

The effects of the following parameters on mechanical properties of carburized and tempered EN-8 samples, are also
examined.

Impact Factor (JCC): 4.8765 NAAS Rating: 2.79

Effect of Carburization on the Mechanical Properties of EN-8 Steel in different Quenching 3
Medium at different Quenching Time Intervals

• Quenching Time

• Quenching Medium

The Inter Relation between different mechanical properties is observed.

METHODOLOGY
• Selection of Specimen [3]: The chemical composition of EN-8 by (wt %) is given as follows

Element C Mn S P Ni Si Cu Cr Fe
Wt % 0.36% 0.32% 0.05% 0.2% 0.01% 0.03% 0.01% 0.01% 0.01%

• Preparation of Test Specimens: The test specimens for analysis of different mechanical properties like tensile
strength, hardness, and case depth and grain structure are prepared as per British Standard and its description is
given below.
• Specimen for Microstructure Study: The specimen for observing the microstructure is prepared by cutting
pieces about ½ inch in height from the heat treated raw material rod. It is dipped in 2% Nital solution for 30 secs
and dried, after which it is viewed under the microscope.

Figure 1: Sample Specimen for Observing Microstructure, Case Depth, Tensile Strength, Hardness.

• Specimen for Case Depth Measurement: The specimen of ½ inch height is taken from the heat treated area and
grounded and polished. After washing and drying, it is etched with 2-4% Nital. Surface is then studied under tool
maker’s microscope.
• Specimen for Tensile Strength Test: A tensile test specimen as per British standard is prepared for the purpose,
based on the following equation-

L0/D0= 5

L0= Gauge Length

D0= Diameter

Figure 2: Sample Specimen for Tensile Strength Test

Hardness Test
[7]
Vickers hardness testing is the method used for measuring the hardness of the EN-8 steel. Although hardness

www.tjprc.org [email protected]
4 BSR Venu Madhav, Abdul Ahad Mohiuddin & Mohammed Atifuddin

testing does not give a direct measurement of any performance properties, hardness correlates with strength, wear
resistance, and other properties.

Figure 3: Vickers Hardness Test

Tensile Test

The tensile strength is widely used to determine strength, ductility, resilence, toughness and several other
mechanical properties. The Universal Testing machine is used to conduct tensile test on the EN-8 specimens.

Figure 4: Universal Testing Machine

Carburization of Steel Samples

The different test specimen samples made up of EN-8 steel for mechanical properties testing are subjected to
carburization treatment. The EN-8 steel samples are carburized and then they are quenched in water, air and oil [11], i.e. the
hardening is affected immediately after carburization. The carburized steel samples are then tempered for a particular
temperature and time and then processed for different tests. By this carburization process the mechanical properties of
tempered EN-8 steel samples have increased considerably [5].

RESULTS

The different kinds of EN-8 steel samples are carburized and tempered under the different conditions and the
microstructure is analyzed and later tensile strength test, case depth test and hardness test are calculated.

Results of Microstructure Analysis

The microstructures of all the specimens were studied at both core and case regions were observed at suitable
magnifications. The description of each microstructure is structured in Table 1.

Impact Factor (JCC): 4.8765 NAAS Rating: 2.79

Effect of Carburization on the Mechanical Properties of EN-8 Steel in different Quenching 5
Medium at different Quenching Time Intervals

Figure 5.1(a): Microstructure of Core for Figure 5.1(b): Microstructure of Case for
Uncarburised EN-8 Uncarburised EN-8

Figure 5.2(a): Microstructure of Core for Carburized Figure 5.2(b): Microstructure of case for carbirized
EN-8 Quenched with air for 60 Minutes EN-8 quenched with air for 60 minutes

Figure 5.3(a): Microstructure of Core for Carburized Figure 5.3(b): Microstructure of Case for Carburized
EN-8 Quenched with Air for 70 Minutes EN-8 Quenched with Air for 70 Minutes

Figure 5.4(a): Microstructure of Core for Carburized Figure 5.4(b): Microstructure of Case for Carburized
EN-8 Quenched with Air for 80 Minutes EN-8 Quenched with Air for 80 Minutes

Figure 5.5(a): Microstructure of Core for Carburized Figure 5.5(b): Microstructure of Case for Carburized
EN-8 Quenched with Oil for 60 Minutes EN-8 Quenched with Oil for 60 Minutes

www.tjprc.org [email protected]
6 BSR Venu Madhav, Abdul Ahad Mohiuddin & Mohammed Atifuddin

Figure 5.6(a): Microstructure of Core for Carburized Figure 5.6(b): Microstructure of Case for Carburized
EN-8 Quenched with Oil for 70 Minutes EN-8 Quenched with Oil for 70 Minutes

Figure 5.7(a): Microstructure of Core for Carburized Figure 5.7(b): Microstructure of Case for Carburized
EN-8 Quenched with Oil for 80 Minutes EN-8 Quenched with Oil for 80 Minutes

Figure 5.8(a): Microstructure of Core for Carburized Figure 5.8(b): Microstructure of Case for Carburized
EN-8 Quenched with Water for 60 Minutes EN-8 Quenched with Water for 60 Minutes

Figure 5.9(a): Microstructure of Core for Carburized Figure 5.9(b): Microstructure of Case for Carburized EN-8
EN-8 Quenched with Water for 70 Minutes Quenched with Water for 70 Minutes

Figure 5.10(a): Microstructure of Core for Carburized Figure 5.10(b): Microstructure of Case for Carburized
EN-8 Quenched with Water for 80 Minutes EN-8 Quenched with Water for 80 Minutes

Impact Factor (JCC): 4.8765 NAAS Rating: 2.79

Effect of Carburization on the Mechanical Properties of EN-8 Steel in different Quenching 7
Medium at different Quenching Time Intervals

Table 5.1: Description of Microstructure[10]

Quenching Medium Quenching Time Remarks
Case: Abnormal Ferrite around the grain
Air 60 Minutes boundaries in matrix of Pearlite
Core: 70% Ferrite,30% Pearlite
Case: Pearlite+Proeutectoid Ferrite
Air 70 Minutes outlining prior to austenite grain
Core: 65% Ferrite,35% Pearlite
Case: Proeutectoid Ferrite outlining prior
Air 80 Minutes to austenite grain
Core: 65% Ferrite,35% Pearlite
Case: Tempered Martensite in matrix
Water 60 Minutes
Core: Ferrite and Pearlite in matrix
Case: Tempered Martensite in matrix
Water 70 Minutes
Core: Ferrite and Martensite in matrix
Case: Tempered Martensite in matrix
Water 80 Minutes
Core: Ferrite and Martensite in matrix
Case: Martensite retained Austenite in the
matrix
Oil 60 Minutes
Core: 45% Ferrite and 55% Martensite in
matrix
Case: Fine tempered Martensite in the
Oil 70 Minutes matrix
Core: Tempered Martensite in the matrix
Case: Coarse Martensite in the matrix
Oil 80 Minutes
Core: Tempered Martensite in the matrix

Results of Case Depth

The results of the case depth measurement test, for different carburization conditions are tabulated and are shown
in Table 5.2. Plots showing the variation in case depth, with respect to each input parameter are shown in Graphs 5.1 &
5.2.

It can be observed that, the case depth increases with increase in quenching time, when the medium is similar.
Also, for a given quenching time, the case depth is highest for water followed by oil and then air.

Table 5.2: Case Depth for different Quenching Media and Time
Quenching Quenching Case Depth(mm)
Medium Time (min) Measurement 1 Measurement 2 Measurement 3 Average
Air 60 0.91 0.933 0.915 0.919
Air 70 0.93 0.94 0.95 0.94
Air 80 0.957 0.95 0.97 0.959
Oil 60 0.991 0.989 0.981 0.987
Oil 70 0.995 0.987 0.997 0.993
Oil 80 1.011 0.007 1.012 1.01
Water 60 0.991 1.003 0.997 0.998
Water 70 1.01 0.99 1.027 1.012
Water 80 1.03 1.12 1.09 1.08

www.tjprc.org [email protected]
8 BSR Venu Madhav, Abdul Ahad Mohiuddin & Mohammed Atifuddin

Graph 5.1: Case Depth vs. Quenching Time for various Quenching media

Graph 5.2: Case Depth vs. Quenching media for various Quenching time

Results of Tensile Tests

The Heat treatment and Carburization of EN-8s resulted in an increase in hardness. Tensile strength and wear
resistance and decreased the weight loss during abrasion and toughness values. The tests results of different mechanical
characteristics like tensile strength and hardness under the different carburization conditions arc shown in Table 5.3,5.4
and 5.5 and summarized the following points.

• The tensile strength is varied between the ranges of 650 MPa — 1650 MPa (Table 5.3)[6] and is highest for the
steel carburized for 8 hours, followed by Water Quenching for 80 Minutes and lowest for the steel carburized for
8 hours, followed by Air Quenching for 60 Minutes, so with increase of quenching time the tensile strength
increases. This is also shown graphically in the Graph 5.3 & Graph 5.4. This result shows that, the carburization
improved the tensile strength of EN-8.

• The hardness values varied between range of 296 HV to 765.33 HV (Table 5.4 and 5.5) and it is highest for the
EN-8 steel Quenched for 80 Minutes in water and is lowest for the EN-8 steel Quenched for 60 Minutes in air, so
with increase of quenching time the hardness values increase. This is also shown graphically in the Graph 5.5 &
Graph 5.6.

• The Tensile Strength values are directly proportional to the Hardness values. As the Hardness values increases,
the Tensile strength also increases. This is also graphically shown Graph 5.7.

Finally the Net result is that the EN-8 Steel quenched for 80 minutes in Water medium is giving the best results
for the mechanical and wear properties like Tensile strength and Hardness [8].

Impact Factor (JCC): 4.8765 NAAS Rating: 2.79

Effect of Carburization on the Mechanical Properties of EN-8 Steel in different Quenching 9
Medium at different Quenching Time Intervals

Table 5.3: Tensile Strength for different Quenching Media and Time
Quenching Quenching Tensile
Medium Time (min) Strength(Mpa)
Air 60 656.958
Air 70 675.805
Air 80 910.64
Oil 60 962.218
Oil 70 1363.856
Oil 80 1421.98
Water 60 983.29
Water 70 997.12
Water 80 1649.172

Graph 5.3: Tensile Strength vs. Quenching for various Quenching Media

Graph 5.4: Tensile Strength vs. Quenching Time Media for various Quenching Time

Table 5.4: Case Hardness Values for different Quenching Media and Time
Quenching Quenching Case Hardness
Medium Time (min) Impression 1 Impression 2 Impression 3 Average
Air 60 297 294 297 296
Air 70 322 319 319 320
Air 80 327 325 327 326.33
Oil 60 429 425 429 427.33
Oil 70 498 493 498 496.33
Oil 80 657 649 649 651.33
Water 60 390 390 387 389
Water 70 498 464 498 466.67
Water 80 772 762 762 765.33

www.tjprc.org [email protected]
10 BSR Venu Madhav, Abdul Ahad Mohiuddin & Mohammed Atifuddin

Table 5.5: Core Hardness Values for different Quenching Media and Time
Quenching Quenching Core Hardness
Medium Time (min) Impression 1 Impression 2 Impression 3 Average
Air 60 159 160 159 159.33
Air 70 147 146 147 146.67
Air 80 264 262 264 263.33
Oil 60 212 210 212 211.33
Oil 70 387 383 383 384.33
Oil 80 227 225 225 225.67
Water 60 254 256 254 254.67
Water 70 193 194 193 193.33
Water 80 354 253 254 287

Graph 5.5: Hardness vs. Quenching Time for various Quenching media

Graph 5.6: Hardness vs. Quenching Media for various Quenching time

Graph 5.7: Tensile Strength vs. Hardness

Impact Factor (JCC): 4.8765 NAAS Rating: 2.79

Effect of Carburization on the Mechanical Properties of EN-8 Steel in different Quenching 11
Medium at different Quenching Time Intervals

CONCLUSIONS

From the present studies on "Effect of Carburization on the Mechanical Properties of EN-8 by varying the
Quenching Medium and Quenching Time” - the following conclusion have been drawn.

• The mechanical properties of EN-8 were found to be strongly influenced by the process of carburization.

• 2. The carburization treatment followed by the quenching appreciably improved the hardness and tensile strength
of EN-8s.

• 3. Hardness, case depth and tensile strength increased with increase in the quenching time.

• 4. The quenching medium also deeply affected the mechanical properties of EN-8

• 5. For a given quenching time, hardness, case depth and tensile strength are more, for water-quenched and least
for air-quenched steels. Oil-quenched show intermediate values.

• 6. As comparing for different quenching times, The EN-8 quenched for 80 minutes shows the best combination of
higher hardness, higher tensile strength.

• 7. As comparing for different quenching media, The EN-8 quenched in water medium, shows the best
combination of higher hardness, higher tensile strength.

• 8. Finally the net conclusion is that the EN-8 carburized and quenched under the different quenching media air,
water and oil, quenching time for 60, 70, 80 minutes, with in which the best results for the mechanical and wear
properties like tensile strength, hardness were given by 80 minutes water quenched EN-8.

REFERENCES

1. Dieter G. E., Mechanical Metallurgy, 3rd Edn., McGraw Hills, Singapore, 1988, P —277, 333, 334.

2. Satish Kumar et al - Heat Treatment on En 8 & En 353 For Heavy Duty Gears

3. Wieser P. F. Steel casting Handbook, 5th Edn., Steel Founders Society of America, Ohio, 1980, P —4.

4. Singh V., Physical Metallurgy, Standard Publisher, Delhi, 2007, p — 482.

5. Senthil Kumar - Effect of Heat Treatment Processes on the Mechanical Properties of Medium Carbon Steel

6. J K Odusote et al - Mechanical Properties of Medium Carbon Steel Quenched in Water and Oil

7. Hellenic society or Nondestructive testing, (increase - Case depth determination. -, using Vickers micro - hardness test method

8. M. B. Ndaliman - An Assessment of Mechanical Properties of Medium Carbon Steel under Different Quenching Media.

9. Adnan Kalik - Effect of Carbon Content on the Mechanical Properties of Medium Carbon Steels

10. Cullen M. Moleejane - Microstructure' Features and Mechanical Behavior of Unalloyed Medium Carbon Steel (ENS Steel)
after Subsequent Heat Treatment

11. Daniel H. Herring - Oil Quenching.

www.tjprc.org [email protected]