WHAT’S IN THE BOX

ELECTRIC
AIR PUMP
130W
Electric Air Pump
INSTRUCTION MANUAL
SPECIFICATIONS
Voltage: 220-240V ~50Hz
Power: 130W
Max. Current: 0.62A
Max. Pressure: 0.6PSI
Flow Rate: 440L/Min
Inflation Time: Under 2min 3 x Inflation Adaptors
(double air mattress)
Max. Run Time: 15min
Weight: 0.55kg

ozito.com.au

IDP-2000
KNOW YOUR PRODUCT SETUP & PREPARATION
ELECTRIC AIR PUMP
1 Inflation Port 4 Deflation Port 1. ADAPTORS
2 On/Off Switch 5 Power Cord
3 Air Pump Housing
WARNING: Ensure the tool is switched off and
disconnected from the power supply before
performing any of the following Steps.

Fitting an Adaptor

1 A
 lign the required adaptor with
the port.

2 P
 ush the adaptor
onto the air port
tightly.

1 2 3 4 5

Removing Adaptors
ACCESSORIES
1 T
 o remove, simply
6 Inflation Adaptors
pull the adaptor from
the air port.

ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
OPERATION

2. SWITCHING ON & OFF 3. INFLATING ITEMS

CAUTION! The power supply for this product IMPORTANT: Before connecting OR
should be protected by a residual current DISCONNECTING accessories, always make sure
device (rated at 30mA or less). that the Air Pump is TURNED OFF.

1 F
 it the required adaptor onto
1 T
 o start operating the air the inflation port tightly.
pump, push the on/off switch
to the on position.

2 Insert the adaptor

into the valve of the
inflatable item.

2 T
 o stop operation,
push the on/off
switch to the off
position.

CAUTION: Ensure the deflation port is not

obstructed, otherwise the unit could overheat.

3 S
 witch the air pump on at the
WARNING: COMPRESSED AIR CAN BE DANGEROUS. on/off switch.
Never point the outlet nozzle towards any
part of your body or AT another person.

4 Once the item is

inflated, switch the
air pump off and then
remove the adaptor
from the valve.

WARNING: Avoid inflating the objects above

the recommended inflation pressure. This may
lead to damage and/or injuries.
 4. DEFLATING ITEMS

IMPORTANT: Before connecting OR

DISCONNECTING accessories, always make sure
that the Air Pump is TURNED OFF.

1 F
 it the required
adaptor onto the
deflation port at the
top of the unit tightly.

2 Insert the adaptor

into the valve of the
inflatable item.

CAUTION: Ensure the inflation port is not

obstructed, otherwise the unit could overheat.

3 S
 witch the air pump on at the
on/off switch.

4 Once the item is

deflated, switch the
air pump off and then
remove the adaptor
from the valve.

IDP-2000
MAINTENANCE DESCRIPTION OF SYMBOLS

WARNING: Before cleaning or carrying out

any maintenance procedure, ensure the unit
is switched off, disconnected from the power
supply and allowed to cool down. A Amps

Double insulated

Cleaning
• Keep the ventilation vents of the air pump clean at all times, if
possible, prevent foreign matter from entering the vents.

• After each use, blow air through the air pump housing to ensure it is
free from all dust particles which may build up. Build up of dust particles
may cause the air pump to overheat and fail.

• If the enclosure of the air pump requires cleaning do not use solvents
but a moist soft cloth only. Never let any liquid get inside the product; CARING FOR THE ENVIRONMENT
never immerse any part of the air pump into a liquid.

Power tools that are no longer usable should not be disposed of

Note: Ozito Industries will not be responsible for any damage or with household waste but in an environmentally friendly way. Please
injuries caused by the repair of the air pump by an unauthorised person recycle where facilities exist. Check with your local council authority
or by mishandling of the product. for recycling advice.

Recycling packaging reduces the need for landfill and raw materials.
Reuse of recycled material decreases pollution in the environment.
Please recycle packaging where facilities exist. Check with your
IMPORTANT: Store the air pump only in a dry location local council authority for recycling advice.
which is not accessible to unauthorised persons.

TROUBLESHOOTING SPARE PARTS

Problem Cause Solution Spare parts can be ordered from the Special Orders Desk
at your local Bunnings Warehouse.
The air pump Cord not connected to  onnect the power
C
does not start the power cord to a 240V For further information, or any parts not listed here, visit
power outlet www.ozito.com.au or contact Ozito Customer Service:
On/off switch not in on Push the on/off Australia 1800 069 486
position switch into the on
position New Zealand 0508 069 486
E-mail: [email protected]
Adaptors disconnect Loose adaptor  nsure the adaptor
E
when the pump is pushed tightly
switches on onto the air port

Pump is operating Some inflatable items Pinch or unscrew

but the inflatable have a check valve the items valve
item is not inflating/ that require pinching or while operating the
deflating unscrewing pump

Pump is overheating While inflating, the Ensure the deflation

deflation port is being port is free of any
obstructed, restricting obstructions
the flow of the air pump
While deflating, the Ensure the inflation
inflation port is being port is free of any
obstructed, restricting obstructions
the flow of the air pump
 Tool: Electric Air Pump
SPARE PARTS Model No. IDP-2000

How To Order

Available spare parts can be ordered through the Special Orders Desk at any Bunnings Warehouse. If you have any
further questions, please contact Ozito Customer Service on:
Australia: 1800 069 486
New Zealand: 0508 069 486
[email protected]
 ELECTRICAL SAFETY
WARNING! When using mains-powered tools, basic safety precautions, including the The supply cord cannot be replaced. If the cord is damaged the appliance should be scrapped.
following, should always be followed to reduce risk of fire, electric shock, personal injury Note: Double insulation does not take the place of normal safety precautions when operating this tool. The
and material damage. insulation system is for added protection against injury resulting from a possible electrical insulation failure
Read the whole manual carefully and make sure you know how to switch the tool off in an emergency, before within the tool.
operating the tool.
Save these instructions and other documents supplied with this tool for future reference. Using an Extension Lead
The electric motor has been designed for 230V and 240V only. Always check that the power supply Always use an approved extension lead suitable for the power input of this tool. Before use, inspect the
corresponds to the voltage on the rating plate. extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged or defective.
Note: The supply of 230V and 240V on Ozito tools are interchangeable for Australia and New Zealand. When using an extension lead on a reel, always unwind the lead completely. Use of an extension lead
not suitable for the power input of the tool or which is damaged or defective may result in a risk of fire and
electric shock.
This tool is double insulated in accordance with AS/NZS 60335-1;
therefore no earth wire is required.

GENERAL POWER TOOL SAFETY WARNINGS-PERSONAL SAFETY

WARNING! Read all safety warnings and all instructions. Failure to follow the d. Remove any adjusting key or wrench before turning the power tool on.
warnings and instructions may result in electric shock, fire and/or serious injury. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
Save all warnings and instructions for future reference. The term “power tool” in the e. Do not overreach. Keep proper footing and balance at all times. This enables better control
warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) of the power tool in unexpected situations.
power tool. f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves
1. Work area safety away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
a. Keep work area clean and well lit. Cluttered or dark areas invite accidents. g. If devices are provided for the connection of dust extraction and collection facilities,
b. Do not operate power tools in explosive atmospheres, such as in the presence of flammable ensure these are connected and properly used. Use of dust collection can reduce dust-
liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. related hazards.
c. Keep children and bystanders away while operating a power tool. Distractions can cause 4. Power tool use and care
you to lose control. a. Do not force the power tool. Use the correct power tool for your application. The correct
2. Electrical safety power tool will do the job better and safer at the rate for which it was designed.
a. Power tool plugs must match the outlet. Never modify the plug in any way. b. Do not use the power tool if the switch does not turn it on and off. Any power tool that
Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and cannot be controlled with the switch is dangerous and must be repaired.
matching outlets will reduce risk of electric shock. c. Disconnect the plug from the power source and/or the battery pack from the power tool
b. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges before making any adjustments, changing accessories, or storing power tools. Such
and refrigerators. There is an increased risk of electric shock if your body is earthed or preventive safety measures reduce the risk of starting the power tool accidentally.
grounded. d. Store idle power tools out of the reach of children and do not allow persons unfamiliar
c. Do not expose power tools to rain or wet conditions. Water entering a power tool will with the power tool or these instructions to operate the power tool. Power tools are
increase the risk of electric shock. dangerous in the hands of untrained users.
d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of
tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled parts and any other condition that may affect the power tool’s operation. If damaged,
cords increase the risk of electric shock. have the power tool repaired before use. Many accidents are caused by poorly maintained
e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. power tools.
Use of a cord suitable for outdoor use reduces the risk of electric shock. f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting
f. If operating a power tool in a damp location is unavoidable, use a residual current device edges are less likely to bind and are easier to control.
(RCD) protected supply. Use of an RCD reduces the risk of electric shock. g. Use the power tool, accessories and tool bits etc. in accordance with these instructions,
3. Personal safety taking into account the working conditions and the work to be performed. Use of the
a. Stay alert, watch what you are doing and use common sense when operating a power power tool for operations different from those intended could result in a hazardous situation.
tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol 5. Service
or medication. a. Have your power tool serviced by a qualified repair person using only identical
A moment of inattention while operating power tools may result in serious personal injury. replacement parts. This will ensure that the safety of the power tool is maintained.
b.  Use personal protective equipment. Always wear eye protection. Protective equipment
such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting
to power source and/or battery pack, picking up or carrying the tool. Carrying power
tools with your finger on the switch or energising power tools that have the switch on invites
accidents.

AIR PUMP SAFETY WARNINGS

This appliance is not intended for use by persons (including children) with toys.
reduced physical, sensory or mental capabilities, or lack of experience and • A
 void inserting hands into the inlets/outlets of the air pump while it is connected to
knowledge, unless they have been given supervision or instruction concerning power.
use of the appliance by a person responsible for their safety.
• B
 efore using the air pump, always inspect it visually. Do not use the pump if it is
Children should be supervised to ensure that they do not play with the appliance.
cracked and/or damaged. If the pump is damaged, contact Ozito customer service.
• Do not place the hose end against any part of your body when turned on, as this • N
 ever work or perform maintenance on the pump without first making sure it has
may infuse air into your blood stream putting your health at serious risk. been disconnected from the mains power.
• Do not make any alterations to this air pump. Only use the adaptors supplied
with this product. IMPORTANT:
• Use this product only in accordance with operation instructions included in this • T
 he electrical connection must always be made in a dry area. Make sure that
manual. electrical connections are protected from inundations.
• It is not suggested that the air pump work continuously for more than 15 • Protect the plug and the power cable from heat, oil or sharp edges.
minutes. If 15 minutes of use has been reached, turn it off and let it cool for 8
• If damaged, The power cable must be replaced by a qualified electrician.
minutes before using again.
• If the pump is making abnormal sounds or its temperature is quite high, turn
off the power straight away and let it cool for at least 10 minutes before trying again.
Improper use may result in damage of the air pump.
• Do not leave unattended and operating. Keep out of reach of children.
• Put the air pump in a dry place if it is not in use for an extended period of time.
• Keep the air pump away from flammable liquid or gas. Do not allow the
pump to become wet.
• Never put the connector and adaptors into your mouth, ear or eye. They are not
 WARRANTY
IN ORDER TO MAKE A CLAIM UNDER THIS The benefits provided under this warranty are in addition
to other rights and remedies which are available to you at law.
WARRANTY YOU MUST RETURN THE PRODUCT
Our goods come with guarantees that cannot be excluded
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH at law. You are entitled to a replacement or refund for a major
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO failure and for compensation for any other reasonably foreseeable
RETURNING YOUR PRODUCT FOR WARRANTY loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
PLEASE TELEPHONE OUR CUSTOMER SERVICE failure does not amount to a major failure.
HELPLINE: Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
Australia 1800 069 486 any additional direct loss as a result of a defective product you
New Zealand 0508 069 486 may be able to claim such expenses by contacting our customer
service helpline above.

TO ENSURE A SPEEDY RESPONSE PLEASE 3 YEAR REPLACEMENT WARRANTY

HAVE THE MODEL NUMBER AND DATE OF
Your product is guaranteed for a period of 36 months from
PURCHASE AVAILABLE. A CUSTOMER SERVICE the original date of purchase. If a product is defective it will
REPRESENTATIVE WILL TAKE YOUR CALL be replaced in accordance with the terms of this warranty.
AND ANSWER ANY QUESTIONS YOU MAY Warranty excludes consumable parts, for example: valve adaptors
etc.
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE. WARNING
The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other
than that specified on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the
instruction manual.
• If the tool is disassembled or tampered with in any way.
• Professional, industrial or high frequency use.

OZITO Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175. 0915