Scribd
Upload
115 views1 page

477TC

This document summarizes the specifications of the 477TC No-Skive PowerLift Tough Cover hose. It is a nitrile rubber hose with two steel wire braids and a highly abrasion resistant synthetic rubber cover. It is suitable for applications such as cranes, fork lifts, and lifting equipment handling mineral oil up to 70°C. The hose comes in various sizes with minimum bend radii ranging from 65 to 250mm and maximum working pressures from 28 to 45MPa depending on the size.

Uploaded by

Jas Sum
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
115 views1 page

477TC

This document summarizes the specifications of the 477TC No-Skive PowerLift Tough Cover hose. It is a nitrile rubber hose with two steel wire braids and a highly abrasion resistant synthetic rubber cover. It is suitable for applications such as cranes, fork lifts, and lifting equipment handling mineral oil up to 70°C. The hose comes in various sizes with minimum bend radii ranging from 65 to 250mm and maximum working pressures from 28 to 45MPa depending on the size.

Uploaded by

Jas Sum
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Medium Pressure Parkrimp No-Skive Hose

Powerlift 477TC

477TC
Elite No-Skive PowerLift Tough Cover
2 wire braided

• No-Skive hose construction


– Compact design
• Smaller bend radius and reduced
outside diameter bringing a significant
advantage in terms of space and weight
Primary Applications on compact equipment
For truck cranes and lifting equipment such as fork lift
• Highly abrasion resistant
trucks, aerial lifts, cranes, telehandlers, lifting platforms.
• MSHA approved
Restrictions • Hose is suitable for temporary immersion
Should not be used for high impulse hydraulic in mineral oil up to 70 °C with frequent
applications to replace spiral construction hoses. inspections

Construction Recommended Fluids


Inner Tube: Nitrile (NBR) Hydraulic fluids on a mineral-oil basis, water-glycol and
Reinforcement: Two high-tensile steel wire braids lubricating oils, air and water. For air and gas applications
Cover: Highly abrasion resistance with a pressure exceeding 1.7 MPa, the cover must be
MSHA approved synthetic rubber pin-pricked.
Consult the chemical compatibility section on
Temperature Range ............ -40 °C up to +100 °C pages Ab-26 to Ab-34 for more detailed information.
Exception: Air .................................... max. +70 °C
Water ............................... max. +85 °C Fitting Series 48

Hose
Pressure Rating

max. min.
Part Number Hose Hose working burst min. bend
weight
I.D. O.D. pressure pressure radius

477 <tab>Hose
DN
DN Inch
Zoll Size
size mm
mm mm
OD MPa
MPa1 psi
psi1 MPa
MPa2 psi
psi2 mm
Bend kg
weight
477TC-4 6 1/4 -4 6.4 13.1 45.0 6500 180.0 26000 65 0.32
477TC-5 8 5/16 -5 7.9 14.9 42.5 6100 170.0 24400 70 0.35
477TC-6 10 3/8 -6 9.5 17.2 40.0 5800 160.0 23200 75 0.42
477TC-8 12 1/2 -8 12.7 20.4 38.0 5500 152.0 22000 105 0.55
477TC-10 16 5/8 -10 15.9 23.4 35.0 5000 140.0 20000 160 0.65
477TC-12 19 3/4 -12 19.1 27.2 35.0 5000 140.0 20000 200 1.10
477TC-16 25 1 -16 25.4 34.8 28.0 4000 112.0 16000 250 1.34
The combination of high temperature and high pressure could reduce the hose life.

Hose layline example

Cab-27 Catalogue 4400/UK

You might also like