Buttons on remote controller

1 ON/OFF button
2 ▲ button
3 MODE button
4 SWING button
button
▲
5
6 FAN button
2 1 7 TIMER OFF button
3 8 CLOCK button
5
6 9 TIMER ON button
4
9 7 10 SLEEP button
8 10 11 TEMP button
12 11
12 TURBO button
15 13
14 13 X-FAN button
14 I FEEL button
15 / button

Introduction for icons on display screen

I feel Set fan speed
Send signal
8℃ heating function Turbo mode
Operation mode ventilation operation
health function
Auto mode X-fan mode
Cool mode
Set temperature
Dry mode
Fan mode Set time
Heat mode
TIMER ON /
Clock TIMER OFF
Sleep mode Child lock
Light Up & down swing
Temp. display type
:Set temp. :Indoor ambient temp.
:Outdoor ambient temp.

9
Introduction for buttons on remote controller
Note:
● After putting through the power, the air conditioner will give out a sound.
Operation indictor " " is ON (red indicator). After that, you can operate the air
conditioner by using remote controller.
● Under on status, pressing the button on the remote controller, the signal icon " "
on the display of remote controller will blink once and the air conditioner will give
out a “de” sound, which means the signal has been sent to the air conditioner.
● Under off status, set temperature and clock icon will be displayed on the display
of remote controller (If timer on, timer off and light functions are set, the corre-
sponding icons will be displayed on the display of remote controller at the same
time); Under on status, the display will show the corresponding set function icons.

1 ON/OFF button
Press this button to turn on the unit. Press this button again to turn off the unit.

2 ▲ button
Press this button to increase set temperature. Holding it down above 2 seconds rapidly
increases set temperature. In AUTO mode, set temperature is not adjustable.

3 MODE button
Each time you press this button,a mode is selected in a sequence that goes from
AUTO, COOL, DRY, FAN, and HEAT *, as the following:
AUTO COOL DRY FAN HEAT*
* Note: Only for models with heating function.

After energization, AUTO mode is defaulted. In AUTO mode, the set temperature will
not be displayed on the LCD, and the unit will automatically select the suitable opera-
tion mode in accordance with the room temperature to make indoor room comfortable.

4 SWING button
Press this button to set up & down swing angle, which circularly changes as below:

OFF

This remote controller is universal. If any command , or is sent out,

the unit will carry out the command as
indicates the guide louver swings as:

5 button
▲

Press this button to decrease set temperature. Holding it down above 2 seconds rapidly
decreases set temperature. In AUTO mode, set temperature is not adjustable.
10
Introduction for buttons on remote controller
6 FAN button
This button is used for setting Fan Speed in the sequence that goes from AUTO,
, to , then back to Auto.
Auto

Low speed Medium speed High speed

7 TIMER OFF button

Press this button to initiate the auto-off timer. To cancel the auto-timer program, simply
press the button again. TIMER OFF setting is the same as TIMER ON.

8 CLOCK button
Press CLOCK button, blinking. Within 5 seconds, pressing ▲ or button adjusts the
▲
present time. Holding down either button above 2 seconds increases or decreases the
time by 1 minute every 0.5 second and then by 10 minutes every 0.5 second. During
blinking after setting, press CLOCK button again to confirm the setting, and then
will be constantly displayed.

9 TIMER ON button
Press this button to initiate the auto-ON timer. To cancel the auto-timer program, simply
press this button again.
After press of this button, disappears and "ON "blinks. 0 0:00 is displayed for ON time
setting. Within 5 seconds, press ▲ or button to adjust the time value. Every press of
▲
either button changes the time setting by 1 minute. Holding down either button rapidly
changes the time setting by 1 minute and then 10 minutes. Within 5 Seconds after
setting, press TIMER ON button to confirm.

10 SLEEP button
Press this button to go into the SLEEP operation mode. Press it again to cancel this
function. This function is available in COOL, HEAT (Only for models with heating
function) to maintain the most comfortable temperature for you.

11 TEMP button
Press this button, you can see indoor set temperature, indoor ambient temperature
on indoor unit’s display. The setting on remote controller is selected circularly as below:
no display

When selecting " " with remote controller or no display, temperature indicator on indoor
11
Introduction for buttons on remote controller
unit displays set temperature; When selecting " " with remote controller, temperature
indicator on indoor unit displays indoor ambient temperature; 3s later or within 3s it
receives other remote controller signal that will return to display the setting temperature.
Caution:
• This model hasn't outdoor ambient temperature display function. While remote controller
can operate " " and indoor unit displays set temperature.
• It’s defaulted to display set temperature when turning on the unit.
• Only for the models with temperature indicator on indoor unit.

12 TURBO button
Press this button to activate / deactivate the Turbo function which enables the unit to
reach the preset temperature in the shortest time. In COOL mode, the unit will blow
strong cooling air at super high fan speed. In HEAT mode, the unit will blow strong
heating air at super high fan speed.

13 X-FAN button
X-FAN function: In COOL or DRY mode, the icon is displayed and the indoor fan will
continue operation for 2 minutes in order to dry the indoor unit even though you have
turned off the unit. After energization, X-FAN OFF is defaulted. X-FAN is not available in
AUTO, FAN or HEAT mode.
function: turn on the display's light and press this button again to turn off the display's
light. If the light is turned on, is displayed. If the light is turned off, disappears.

14 I FEEL button
Press this button to turn on I FEEL function. The unit automatically adjust temperature
according to the sensed temperature. Press this button again to cancel I FEEL function.

15 / button
Press this button to achieve the on and off of healthy and scavenging functions in
operation status. Press this button for the first time to start scavenging function; LCD
displays " ". Press the button for the second time to start healthy and scavenging
functions simultaneously; LCD displays " " and " ". Press this button for the third
time to quit healthy and scavenging functions simultaneously. Press the button for the
fourth time to start healthy function; LCD display " ". Press this button again to repeat
the operation above. (This function is applicable to partial of models)

12
Function introduction for combination buttons
Combination of "▲" and " " buttons: About lock
▲

Press "▲" and " " buttons simultaneously to lock or unlock the keypad. If the remote
▲
controller is locked, is displayed. In this case, pressing any button, blinks
three times.
Combination of "MODE" and " " buttons:
▲

About switch between Fahrenheit and centigrade

At unit OFF, press "MODE" and " " buttons simultaneously to switch between ℃ and ℉.
▲

Combination of "TEMP" and "CLOCK" buttons:

About Energy-saving Function
Press "TEMP" and "CLOCK" simultaneously in COOL mode to start energy-saving function.
Nixie tube on the remote controller displays "SE". Repeat the operation to quit the function.
Combination of "TEMP" and "CLOCK" buttons:
About 8℃ Heating Function
Press "TEMP" and "CLOCK" simultaneously in HEAT mode to start 8℃ Heating Function
Nixie tube on the remote controller displays " " and a selected temperature of "8℃".
(46℉ if Fahrenheit is adopted). Repeat the operation to quit the function.
About Back-lighting Function
The unit lights for 4s when energizing for the first time, and 3s for later press.

13
Operation guide
1. After putting through the power, press "ON/OFF" button on remote controller to
turn on the air conditioner.
2. Press "MODE" button to select your required mode: AUTO, COOL, DRY, FAN,
HEAT.
3. Press "▲" or " " button to set your required temperature. (Temperature can’t
▲

be adjusted under auto mode).

4. Press "FAN" button to set your required fan speed: auto, low, medium and high
speed.
5. Press "SWING" button to select fan blowing angle.

Replacement of batteries in remote controller

1. Press the back side of remote controller marked battery

reinstall
the cover of battery box along the arrow direction.
2. Replace two 7# (AAA 1.5V) dry batteries, and remove
make sure the position of "▲" polar and " " polar
▲
are correct.
3. Reinstall the cover of battery box. Cover of battery box

Note:
● During operation, point the remote control signal sender at the receiving
window on indoor unit.
● The distance between signal sender and receiving window should be no
more than 8m, and there should be no obstacles between them.

or wireless telephone; remote controller should be close to indoor unit during

operation.
● Replace new batteries of the same model when replacement is required.
● When you don’t use remote controller for a long time, please take out the
batteries.
● If the display on remote controller is fuzzy or there’s no display, please
replace batteries.

14