ASTM Liquid-in-Glass Thermometers: Standard Specification For

Method 9501—Federal Test
Designation: E 1 – 05 Method Standard No. 791b
Standard Specification for

ASTM Liquid-in-Glass Thermometers1
This standard is issued under the fixed designation E 1; the number immediately following the designation indicates the year of original
adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript
epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope responsibility of the user of this standard to establish appro-

1.1 This specification covers liquid-in-glass thermometers priate safety and health practices and determine the applica-
graduated in degrees Celsius or degrees Fahrenheit that are bility of regulatory limitations prior to use.
frequently identified and used in methods under the jurisdiction 2. Referenced Documents
of the various technical committees within ASTM. The various
thermometers specified are listed in Table 1. The inclusion of 2.1 ASTM Standards: 3
an IP number in Table 1 indicates, where appearing, that the E 77 Test Method for Inspection and Verification of Ther-
thermometer specification has been jointly agreed upon by the mometers
British Institute of Petroleum (IP) and ASTM. E 344 Terminology Relating to Thermometry and Hydrom-
1.2 This specification also covers adjustable-range etry
enclosed-scale thermometers, graduated in degrees Celsius, E 563 Practice for Preparation and Use of an Ice-Point Bath
which are used in ASTM methods. as a Reference Temperature
1.3 The enclosed-scale thermometers are commonly called E 2251 Specification for Liquid-in-Glass ASTM Thermom-
Beckmann thermometers. They are suitable for measuring eters with Low-Hazard Precision Liquids
small temperature differences not exceeding 6 °C within a 3. Terminology
larger range of temperature. The thermometers are unsuitable
for measuring Celsius- or kelvin-scale temperatures unless they 3.1 Definitions—The definitions given in Terminology
have been compared with standard instruments immediately E 344 apply.
before use. 3.2 Definitions of Terms Specific to This Standard:
1.4 An alphabetic list of the ASTM Thermometers included 3.2.1 adjusting device, n—a section of the instrument used
in this standard is given in Table 2. to adjust the amount of mercury in the bulb and main capillary
1.5 A list of ASTM Thermometers is given in Table 3 to to that needed for the intended temperature interval.
facilitate selection according to temperature range, immersion, 3.2.2 bulb length, n—the distance from the bottom of the
and scale-error requirements. bulb to the junction of the bulb and the stem tubing.
3.2.3 contraction chamber, n—an enlargement of the cap-
NOTE 1—For a listing of thermometers recommended for general illary, that will appear below the main scale or between the
laboratory use, the Scientific Apparatus Makers Association Specifications main scale and the auxiliary scale, which serves to reduce its
for General Purpose Glass Laboratory Thermometers may be consulted.2
NOTE 2—It has been found by experience that these ASTM Thermom-
length or to prevent contraction of the liquid column into the
eters, although developed in general for specific tests, may also be found bulb.
suitable for other applications, thus precluding the need for new thermom- 3.2.4 diameter, n—the largest outside dimension of the
eter specifications differing in only minor features. However, it is glass as measured with a ring gage.
suggested that technical committees contact Subcommittee E20.05 before 3.2.5 expansion chamber, n—an enlargement at the top of
choosing a currently specified thermometer for a new method to be sure the capillary to provide protection against breakage caused by
the thermometer will be suitable for the intended application.
excessive gas pressure.
1.6 This standard does not purport to address all of the 3.2.6 interval error, n—the deviation of the nominal value
safety concerns, if any, associated with its use. It is the of a temperature interval from its true value; either for the total
range (total interval) or for a part of the range (partial interval).
3.2.7 saddle, n—the bottom support of the enclosed scale.
1
This specification is under the jurisdiction of ASTM Committee E20 on
Temperature Measurement and is the direct responsibility of Subcommittee E20.05
on Liquid-in-Glass Thermometers and Hydrometers.
3
Current edition approved Nov. 1, 2005. Published December 2005. Originally For referenced ASTM standards, visit the ASTM website, www.astm.org, or
approved in 1939. Last previous edition approved in 2003 as E 1 – 03a. contact ASTM Customer Service at [email protected]. For Annual Book of ASTM
2
Available from SAMA Group of Assocs., 225 Reinekers, Ste. 625, Alexandria, Standards volume information, refer to the standard’s Document Summary page on
VA 23314. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
E 1 – 05
3.2.8 setting temperature, n—the temperature that yields a Thermometer 99F
reading of zero on the main scale for a given adjustment of the
6.2.3 Ring Top (optional only)—Thermometers 11C and
amount of mercury in the bulb and main capillary.
11F.
3.2.9 thermometric liquid, n—the liquid in a liquid-in-glass
thermometer that indicates the value of temperature. 7. Bulb
3.2.10 top of the thermometer, n—the top of the finished
instrument. 7.1 The bulb shall be made of glass having a viscosity of at
3.2.11 total length, n—the distance from the bottom of the least 1014.6 poises at 490 °C (914 °F) and at least 1013.4 poises
bulb to the top of the finished thermometer, including any at 520 °C (968 °F).
special finish at the top. 7.2 Thermometers made with bulb glasses not meeting the
3.2.12 Other descriptions of terms shall be in accordance minimum properties in 7.1 shall not be subjected to tempera-
with the Terminology section of Test Method E 77. tures above 405 °C (760 °F) or be continuously exposed to
temperatures above 370 °C (700 °F).
Part A—Solid-Stem Thermometers
8. Capillary Clearances
4. Specifications
8.1 The following distances between graduations and the
4.1 The individual thermometers shall conform to the de- bulb, and between graduations and enlargements in the capil-
tailed specifications given in Table 1 and to the general lary, shall be minimum limits for thermometers in this speci-
requirements specified in Sections 5-15. fication.
4.2 Thermometers manufactured to previous revisions of
this specification shall retain the same ASTM status as those NOTE 3—In order for a thermometer to be usable over its entire
meeting current specifications. graduated range, graduation marks should not be placed too close to any
enlargement in the capillary. Insufficient immersion of the thermometric
4.3 The encapsulation (jacketing) of the glass of liquid-in- liquid in the main bulb or capillary enlargement, graduation marks placed
glass thermometers with polyfluorinated hydrocarbons will over parts of the capillary that have been changed by manufacturing
change their performance and physical characteristics, includ- operations, or graduations so close to the top of the thermometer that
ing, but not limited to, response time, accuracy, and physical excessive gas pressure results when the thermometric liquid is raised to
dimensions. Therefore, under no circumstances should an this level, may lead to appreciable errors.
encapsulated or otherwise modified ASTM thermometer be 8.1.1 A 13-mm length of unchanged capillary between the
used in performing tests that specify the use of an ASTM bulb and the immersion line or lowest graduation, if the
thermometer. graduation is not above 100 °C (212 °F); a 30-mm length if the
5. Type graduation is above 100 °C (212 °F).
8.1.2 A 5-mm length of unchanged capillary between an
5.1 The thermometers, as specified in Table 1, shall be filled enlargement and the graduation next below, except at the top of
with one of the following liquids: the thermometer.
5.1.1 Mercury, 8.1.3 A 10-mm length of unchanged capillary between an
5.1.2 Mercury thallium eutectic alloy, or enlargement, other than the bulb, and the immersion line or the
5.1.3 Toluene or other suitable liquid colored with a perma- graduation next above, if the graduation is not above 100 °C
nent red dye. (212 °F); a 30-mm length if the graduation is above 100 °C
5.2 The filling above the liquid shall be nitrogen or other (212 °F).
suitable inert gas. 8.1.4 A 10-mm length of unchanged capillary above the
6. Stem highest graduation, if there is an expansion chamber at the top
of the thermometer; a 30-mm length if there is no expansion
6.1 Stem—The stem shall be made of suitable thermometer
chamber. For the purposes of this requirement, “an expansion
tubing and shall have a plain front and enamel back, unless
chamber” is interpreted as an enlargement at the top end of the
otherwise specified in Table 1.
capillary bore which shall have a capacity equivalent to not less
6.2 Top Finish— The top of all thermometers specified in
than 20 mm of unchanged capillary.
Table 1 shall have a plain rounded finish, except the following
8.2 It is possible to manufacture thermometers that comply
which shall have the top finish indicated below (unless
with the specifications given in Table 1, but do not meet the
indicated as optional):
requirements for capillary clearances given above. In any case,
6.2.1 Glass Button Finish:
the distances given in this section shall be the governing factor.
Thermometers 23C, 24C, and 25C
Under no circumstances shall the scales on thermometers be
6.2.2 Special Finish: placed closer than these minimum distances.
6.2.2.1 Suitable for assembly in a standard 304.8-mm (12-
in.) non-sparking metal armor with open face; in a cup case 9. Graduations and Inscriptions
assembly; or in a flushing case assembly: 9.1 All graduation lines, immersion lines, figures, and
Thermometers 58C, 58F, 59C, 59F, 60C, 60F, 97C, 97F, 98C, 98F, letters shall be clearly defined, suitably colored, and perma-
130C, and 130F
nent. The width and the sharpness of the graduation lines shall
6.2.2.2 Suitable for assembly in a 12-in. non-sparking metal be in accordance with 9.2. The middle of the graduation line
armor with open face: shall be determinable.
2
E 1 – 05
9.1.1 A suitably etched thermometer with the etched lines 23C, 24C, and 25C
and figures filled with a pigment shall be considered perma-
9.4.4 Precision Thermometers:
nently marked provided it passes the test for permanency of
65F, 66F, 67C, 67F, and 68C
pigment in Test Method E 77.
9.1.2 A thermometer marked by other means shall also be 9.4.5 Tank Thermometer:
considered permanently marked, provided it passes the test for 97F
permanency of pigment in Test Method E 77.
9.4.6 Solidification Point Thermometers:
9.2 Graduation Lines—All graduation lines shall be
100C and 101C
straight, of uniform width, and perpendicular to the axis of the
thermometer. The width of the graduation lines shall be as 9.4.7 Reid Vapor Pressure:
follows: 18C and 18F
9.2.1 Group 1—Maximum line width 0.10 mm; for ther-
9.4.8 Oxidation Stability:
mometers that may read to fractions of a division, often with
22C and 22F
magnifying aids:
Thermometers 14C, 14F, 26C, 28C, 28F, 29C, 29F, 30F, 33C, 9.5 Scale Below Zero—When a scale extends both above
33F, 34C, 34F, 35C, 35F, 44C, 44F, 45C, 45F, 46C, 46F, 47C, 47F, and below 0 °C or 0 °F, the two parts of the scale shall be
48C, 48F, 50F, 51F, 52C, 56C, 56F, 62C, 62F, 63C, 63F, 64C, 64F,
65C, 65F, 66C, 66F, 67C, 67F, 68C, 68F, 69C, 69F, 70C, 70F, 72C,
differentiated by some means. Examples of suitable means are:
72F, 73C, 73F, 74C, 74F, 89C, 90C, 91C, 92C, 93C, 94C, 95C, 96C, 9.5.1 Different pigment colors for the two parts of the scale,
100C, 101C, 110C, 110F, 111C, 112C, 113C, 113F, 116C, 117C,
118C, 118F, 119C, 119F, 120C, 121C, 126C, 126F, 127C, 128C,
9.5.2 Different style of numerical characters for the two
128F, 129C, 129F, 132C, 133C, and 137C. parts of the scale, and
9.5.3 Use of minus signs before appropriate numbers below
9.2.2 Group 2—Maximum line width 0.15 mm; for ther-
0 °C or 0 °F.
mometers that may be read to the nearest half division or where
the congestion of scale dictates the use of a scale with moderate
fineness: 10. Special Inscription
Thermometers 1C, 1F, 2C, 2F, 3C, 3F, 5C, 5F, 6C, 6F, 7C, 7F, 8C, 10.1 The special inscription specified in Table 1 shall be
8F, 9C, 9F, 10C, 10F, 11C, 11F, 12C, 12F, 13C, 15C, 15F, 16C, 16F, marked on the thermometer in capital letters and Arabic
17C, 17F, 18C, 18F, 19C, 19F, 20C, 20F, 21C, 21F, 22C, 22F, 23C,
24C, 25C, 36C, 37C, 38C, 39C, 40C, 41C, 42C, 43C, 43F, 49C,
numbers without the use of periods. In addition to the special
54C, 54F, 61C, 61F, 71C, 71F, 82C, 82F, 83C, 83F, 84C, 84F, 85C, inscription prescribed in Table 1, each thermometer shall be
85F, 86C, 86F, 87C, 87F, 99C, 99F, 102C, 103C, 104C, 105C, permanently marked with a unique serial number and the
106C, 107C, 108F, 109F, 114C, 122C, 123C, 124C, 125C, 134C,
135C, 135F, 136C, and 136F. manufacturer’s tradename or mark.
10.2 Engraving Revision Date on ASTM Thermometers—
9.2.3 Group 3—Maximum line width 0.20 mm; for ther- Include year of current revision in ASTM designation (for
mometers with more open scales, usually read to the nearest example, ASTM 1C-99).
division, often times under adverse conditions where a bold
graduation is therefore desired: 11. Permanency of Pigment
Thermometers 27C, 57C, 57F, 58C, 58F, 59C, 59F, 60C, 60F,
75F, 76F, 77F, 78F, 79F, 80F, 81F, 88C, 88F, 97C, 97F, 98C, 98F, 11.1 The test for permanency of pigment shall be performed
130C, and 130F. on any convenient portion of the scale section of the thermom-
9.3 Immersion Line—On partial immersion thermometers eter. The pigment shall not chalk, burn out, or loosen as a result
an immersion line shall be permanently marked on the front of of this test (see Test Method E 77).
the thermometer at the distance above the bottom of the bulb as
specified in Table 1 within a tolerance of 60.5 mm, except for 12. Bulb Stability
Thermometers 82F to 87F, which shall have no immersion line. 12.1 The test for bulb stability shall be made for the
The immersion inscription shall be written in capital letters and following thermometers in the temperature range specified
abbreviated (for example, 76 mm immersion shall be written below for 24 h. The scale indications after the test shall be
76 MM IMM). within the maximum scale error specified in Table 1. Obser-
9.4 Terminal Numbers—The terminal number shall be in vations of a reference point before and after the test to give a
full when there are one or more numbered graduations between measure of the degree of bulb stability achieved in manufac-
it and the last full number, before the terminal number. This ture. The bulb is considered stable if the change in indications
rule need not necessarily be followed for: of the thermometer in the test is no more than 0.7 (7⁄10) of the
9.4.1 Saybolt Viscosity Thermometers: maximum scale error found in Table 1. Reference should be
17C, 17F, 19C, 19F, 20C, 20F, 21C, 21F, 77F, 78F, 79F, 80F, and made to Test Method E 77.
81F ASTM Test Temperature
Thermometer Number Range
9.4.2 Kinematic Viscosity Thermometers:
28F, 29F, 30F, 44F, 45F, 46F, 47F, 48F, 72F, 73F, 74F, 110F, 118F, 3C, 8C, 10C, 11C, 70C 360 to 370°C
126F, 128F, and 129F 3F, 8F, 10F, 11F, 70F 680 to 700°F
2C, 7C, 69C, 107C 280 to 290°C
9.4.3 Engler Viscosity Thermometers: 2F, 7F, 69F 540 to 560 °F
3
E 1 – 05
13. Scale Error 14. Case
13.1 Thermometers shall be verified and calibrated at the 14.1 Each thermometer shall be supplied in a suitable case
temperatures specified in Table 4. Partial immersion thermom- on which shall appear the following marking (except when a
eters shall be calibrated for the emergent stem temperatures transparent case is used): the letters “ASTM,” the thermometer
specified in Table 4. number (33C, 33F, etc.), and the temperature range.
13.1.1 At the time of purchase, the scale errors shall be
within the maximum scale error found in Table 1. The 15. Methods of Verification and Calibration
indications of many high temperature and fractionally gradu-
ated thermometers may change with time and continued use 15.1 Thermometers shall be verified and calibrated at the
due to minute changes in bulb volume. Periodic verification of specified immersion in accordance with Test Method E 77.
these thermometers, either over the entire scale or reverifica- 15.2 For partial immersion thermometers, careful consider-
tion at a reference temperature (ice point or steam point), in ation of emergent stem temperatures shall be observed.
accordance with procedures set forth in Test Method E 77, is 15.2.1 During the manufacture of partial immersion ther-
recommended. mometers, the manufacturer shall calibrate the thermometers
13.2 Due to the application requirements for range and so the indicated temperatures are within the maximum permis-
construction of the following thermometers, it is not practical sible errors found in Table 1 when the emergent stem tempera-
to include reference points such as the ice and steam points. tures found in Table 4 are applied to the readings.
13C, 14C, 14F, 17C, 17F, 18C, 18F, 19C, 19F, 20C, 20F, 21C, 21F, 23C, 24C,
26C, 27C, 38C, 49C, 50F, 51F, 56C, 56F, 76F, 77F, 78F, 79F, 80F, 81F, 83C, NOTE 4—To achieve the requirements in 15.2.1, the manufacturer may
83F, 84C, 84F, 87C, 87F, 91C, 92C, 93C, 96C, 98C, 98F, 100C, 101C, 102C, have to measure emergent stem temperatures above its bath, calculate
103C, 104C, 105C, 106C, 107C, 108F, 109F, 111C, 116C, 117C, 122C, 123C, correction factors, and offset its calibrations accordingly. See Test Method
and 124C E 77 for the procedure to correct for emergent stem temperatures.
4
TABLE 1 Specification for ASTM Thermometers
All dimensions are in millimeters.
See Table 4 for Verification and Calibration Temperatures.
Explanatory Notes:
A
An expansion chamber is provided for relief of gas pressure to avoid distortion of the bulb at higher temperatures. It is not for the purpose of joining mercury
separations and under no circumstances should the thermometer be heated above the highest temperature reading.
B
Toluene or other suitable liquid colored red with a permanent dye shall be used as the actuating liquid.
C
Under certain test conditions, the bulb of the thermometer may be 28 °C (50 °F) above the temperature indicated by the thermometer, and at an indicated
temperature of 371 °C (700 °F) the temperature of the bulb is approaching a critical range in the glass. It is therefore not desirable to use this thermometer under
such conditions at indicated temperatures above 371 °C (700 °F) without checking the ice point.
D
Longest graduation lines at 155 °C, 160 °C, 162 °C, 164 °C, 165 °C, and 170 °C, with arrows at 162 °C and 164 °C.
E
The length of the enlargement, and the distance from the bottom of the enlargement to the bottom of the bulb shall be measured with the test gage shown in
Fig. 1.
F
Long, narrow shape.
G
The test temperature shall be indicated by an arrow whether the graduation corresponding to that point is numbered or not.
E 1 – 05
H
5
Long, narrow shape; mercury shall be in the chamber at 0 °C (32 °F).

I
The thermometer shall be made to be mounted in a brass ferrule consisting of a tubular bushing 8.0 mm in outside diameter with a flanged head approximately
12 mm in diameter so that the upper extremity of the 8.0 mm diameter is located 90 mm from the bottom of the bulb.
J
To be marked on the glass stem at least 90 mm from the bottom of the bulb.
K
Glass button finish, see 6.2.1.
L
Long, narrow shape; mercury shall be near bottom of the chamber at 0 °C.
M
For kinematic viscosity thermometers, the ice-point reading shall be taken within 1 h after being at the test temperature for not less than 3 minutes. The ice-
point reading shall be expressed to the nearest 0.01 °C or 0.02 °F and applied as explained in Test Method E 77, Section 13.
N
Thermometers made to these specifications conform also with the requirements for the titer test thermometer of the American Oil Chemists Society and the
Association of Official Agricultural Chemists, except for the special inscription.
O
Capillary clearances must conform to Section 8.
P
Mercury shall be near middle of chamber at 0 °C.
Q
The stem may be either the plain front or lens front type. If the thermometer is of the lens front type, the cross section of the stem shall be such that it will pass
through an 8-mm ring gage but will not enter a 5-mm slot gage.
R
A suitable mercury-thallium alloy shall be used as the actuating liquid.
S
The expansion chamber shall be of the long narrow type 10 to 20 mm in length. The length of unchanged capillary between the nearest graduation mark and
the expansion chamber shall be not less than 10 mm.
T
Mercury shall be near the bottom of the chamber at 0 °C.
U
The length of unchanged capillary between the nearest graduation mark and contraction chamber shall be not less than 10 mm.
V
Change in correction over any 5 °F interval shall not exceed 0.10 °F.
W
Expansion chamber shall be of the long narrow type and there shall be not less than 10 mm of unchanged capillary between the base of the chamber and the
top graduation.
X
Mercury shall be in the chamber at 32 °F.
Y
Over any interval of 2 °C the change in correction shall not exceed 0.02 °C.
Z
Over any interval of 4 °F the change in correction shall not exceed 0.05 °F.
AA
Special finish, see 6.2.2.
BB
The bulb diameter shall not be more than 0.5 mm greater than the stem.
CC
The stem shall be of the lens front type. The cross section of the stem shall be such that it will pass through a 8.0-mm ring gage but will not enter a 5.0-mm
slot gage. A minor diameter of 4 mm is permissible provided that the major diameter is not less than 7 mm.
DD
Bulb bottom shall be essentially hemispherical.
EE
Immersion line shall be omitted.
FF
For Fahrenheit thermometers, dimension G (length of graduated portion) shall be measured as the length of graduated portion corresponding to the nominal
Celsius range.
GG
The immersion line shall be visible in the case opening after assembly. The immersion shall be measured from the bottom of the bulb rather than from the
bottom of the armor. See 6.2.2.
HH
The stem shall be either the round or lens-front type.
II
Contraction chamber to be long narrow type.
JJ
Over any interval of 1 °C the change in correction shall not exceed 0.01 °C. The correction at the lowest temperature of the nominal range shall not change by
more than 0.02 °C immediately after the thermometer has been heated for 15 min at a temperature 30 °C higher, and allowed to cool naturally in air.
KK
The capillary bore shall be large enough in relation to the bulb to ensure that (without tapping) jumping of the meniscus does not exceed one half of the
smallest scale division, when the temperature is rising at a uniform rate not exceeding 0.05 °C/min.
LL
The thermometer is to be calibrated for 100-mm immersion for the main scale, the ice point is to be calibrated for total immersion.
MM
Bulb shape ellipsoidal (see Fig. 2).
NN
This thermometer may be furnished with an optional ring top. See 6.2.3. Addition of a ring top will increase the total length by an amount equal to the outside
diameter of the ring.
OO
The stem shall be of the lens front type. The cross section of the stem shall be such that it will pass through a 7.0 mm ring gage.
ASTM No. 1C-99 1F-99FF 2C-99 2F-99FF 3C-99 3F-99FF

IP No. 62C 73C
Name Partial Immersion Partial Immersion Partial Immersion
Reference Fig. No. 3 3 3
Range −20 to + 150°C 0 to 302°F −5 to + 300°C 20 to 580°F −5 to + 400°CC 20 to 760°FC
For test at
A Immersion, mm 76 76 76
Graduations:
Subdivisions 1°C 2°F 1°C 2°F 1°C 2°F
Long lines at each 5°C 10°F 5°C 10°F 5°C 10°F
Numbers at each 10°C 20°F 10°C 20°F 10°C 20°F
Scale error, max 0.5°C 1°F 1°C 2°F 1°C to 301°C 2°F to 574°F
E 1 – 05
1.5°C above 3°F above
6
301°C 574°F
Special inscription ASTM ASTM ASTM
1C-99 or 1F-99 2C-99 or 2F-99 3C-99 or 3F–99
76 MM IMM 76 MM IMM 76 MM IMM
Expansion chamber:
A A
Permit heating to 200°C 392°F
B Total length, mm 317 to 327 385 to 395 410 to 420
C Stem OD, mm 6.0 to 7.0 6.0 to 7.0 6.0 to 7.5
D Bulb length, mm 19 to 25 10 to 15 10 to 15
E Bulb OD, mm 5.0 to 6.0 5.0 to 6.0 5.0 to 6.0
Scale location:
Bottom of bulb to line at 0°C 32°F 0°C 32°F 0°C 32°F
F Distance, mm 111 to 118 100 to 110 100 to 110
G Length of graduated portion, mm 170 to 200O 225 to 265O 250 to 290O
Ice-point scale:
Range
H Bottom of bulb to ice-point, mm
Contraction chamber:
I Distance to bottom, min, mm
J Distance to top, max, mm
Stem enlargement:
K OD, mm
L Length, mm
M Distance to bottom, mm
A
An expansion chamber is provided for relief of gas pressure to avoid distortion of the bulb at higher temperatures. It is not for the purpose of joining mercury separations and under no circumstances should
the thermometer be heated above the highest temperature reading.
B
Under certain test conditions, the bulb of the thermometer may be 28°C (50°F) above the temperature indicated by the thermometer, and at an indicated temperature of 371°C (700°F) the temperature of the
bulb is approaching a critical range in the glass. It is therefore not desirable to use this thermometer under such conditions at indicated temperatures above 371°C (700°F) without checking the ice point.
O
Capillary clearances shall conform to Section 8.
TABLE 1 Continued
FF
For Fahrenheit thermometers, dimension G (length of graduated portion) shall be measured as the length of graduated portion corresponding to the nominal Celsius range.

IP No. 1C 2C 5C
Name Cloud and Pour Low Cloud and PourB Low Distillation
Range −38 to + 50°C −36 to + 120°F −80 to + 20°C −112 to + 70°F −2 to + 300°C 30 to 580°F
For test at
A Immersion, mm 108 76 total
Graduations:
Scale error, max 0.5°C 1°F 1°C to − 33°C 2°F to − 28°F 0.5°C to 150°C 1°F to 300°F
2°C below − 33°C 4°F below − 28°F 1°C above 150°C 2°F above 300°F
5C-86 or 5F–86 6C-86 or 6F-86 7C-86 or 7F–86
108 MM IMM 76 MM IMM
Expansion chamber:
A
Permit heating to 100°C 212°F 60°C 140°F
E 1 – 05
7

E Bulb OD, mm ≤5.5 and ≥stem ≤5.0 and ≥stem ≤5.0 and ≥stem
Scale location:
Bottom of bulb to line at −38°C −36°F −70°C −94°F 0°C 32°F
O
G Length of graduated portion, mm 65 to 85 70 to 100O 225 to 255O
Ice-point scale:
Range
Stem enlargement:
K OD, mm
L Length, mm
A
B
O
FF
TABLE 1 Continued
IP No. 6C 15C 16C
Name High Distillation Low-Pensky-Martens High-Pensky-Martens
Range −2 to + 400°CC 30 to 760°FC −5 to + 110°C 20 to 230°F 90 to 370°C 200 to 700°F
For test at
A Immersion, mm total 57 57
Graduations:
Subdivisions 1°C 2°F 0.5°C 1°F 2°C 5°F
Long lines at each 5°C 10°F 1°C and 5°C 5°F 10°C 25°F
Scale error, max 1°C to 300°C 2°F to 570°F 0.5°C 1°F 1°C to 260°C 2.5°F to 500°F
1.5°C above 300°C 3°F above 570°F 2°C above 260°C 3.5°F above 500°F
8C-86 or 8F-86 9C-86 or 9F–86 10C-86 or 10F–86
57 MM IMM 57 MM IMM
Expansion chamber:
A A
Permit heating to 160°C 320°F
E 1 – 05
8
Scale location:
Ice-point scale:
Range
Stem enlargement
K OD, mm 7.5 to 8.5 7.5 to 8.5
L Length, mm 2.5 to 5.0E 2.5 to 5.0E
M Distance to bottom, mm 64 to 66 64 to 66
A
C
E
The length of the enlargement, and the distance from the bottom of the enlargement to the bottom of the bulb shall be measured with the test gage shown in Fig. 1.
O
FF
TABLE 1 Continued
FF
ASTM No. 11C-86 11F-86 12C-86 12F-86FF 13C-86
IP No. 28C 64C 64F 47C
Name Cleveland Open Flash Density-Wide Range Loss on Heat
Range −6 to + 400°CC 20 to 760°FC −20 to + 102°C −5 to + 215°F 155 to 170°C
For test at
A Immersion, mm 25 total total
Graduations:
Subdivisions 2°C 5°F 0.2°C 0.5°F 0.5°C
Long lines at each 10°C 10°F 1°C 1°F 1°CD
Numbers at each 20°C 20°F 2°C 5°F 155°C, 160°C, 165°C,
170°C
Scale error, max 2°C to 260°C 5°F to 500°F 0.15°C 0.25°F 0.5°C
4°C above 260°C 7°F above 500°F
11C-86 or 11F–86 12C-86 or 12F–86 13C-86
25 MM IMM
Expansion chamber:
A
Permit heating to 150°C 300°F 200°C
B Total length, mm 305 to 315NN 415 to 425 150 to 160
E Bulb OD, mm ≤4.5 and ≥stem bulb size ≥stem size ≤5.0 and ≥stem
Scale location:
E 1 – 05
9
Bottom of bulb to line at 0°C 32°F −20°C −4°F 155°C

G Length of graduated portion, 210 to 240O 305 to 350O 40 to 60O
mm
Ice-point scale:
Range
H Bottom of bulb to ice-point,
mm
J Distance to top, max, mm 30F
Stem enlargement:
K OD, mm
L Length, mm
A
An expansion chamber is provided for relief of gas pressure to avoid distortion of the bulb at higher temperatures. It is not for the purpose of joining mercury separations, and under no
circumstances should the thermometer be heated above the highest temperature reading.
C
Under certain test conditions, the bulb of the thermometer may be 28°C (50°F) above the temperature indicated by the thermometer, and at an indicated temperature of 371°C (700°F) the
temperature of the bulb is approaching a critical range in the glass. It is therefore not desirable to use this thermometer under such conditions at indicated temperatures above 371°C (700°F) without
checking the ice point.
D
Longest graduation lines at 155°C, 160°C, 162°C, 164°C, 165°C, and 170°C, with arrows at 162°C and 164°C.
F
Long, narrow shape.
O
FF
NN
This thermometer may be furnished with an optional ring top. See 6.2.3. Addition of a ring top will increase the total length by an amount equal to the outside diameter of the ring.
TABLE 1 Continued
IP No. 17C 60C 61C
Name Wax Melting Point Low Softening Point High Softening Point
Range 38 to 82°C 100 to 180°F −2 to + 80°C 30 to 180°F 30 to 200°C 85 to 392°F
For test at
Graduations:
Subdivisions 0.1°C 0.2°F 0.2°C 0.5°F 0.5°C 1°F
Long lines at each 0.5°C 1°F 1°C 1°F 1°C 5°F
Scale error, max 0.1°C 0.2°F 0.2°C 0.4°F 0.3°C 0.5°F
14C-86 or 14F–86 15C-86 or 15F–86 16C-86 or 16F–86
79 MM IMM
Expansion chamber:
Permit heating to 100°C 212°F 130°C 270°F 250°C 482°F
E 1 – 05
10

Scale location:
G Length of graduated portion, mm 210 to 240O 245 to 285 O
245 to 280O
Ice-point scale:
Range
J Distance to top, max, mm 41
Stem enlargement:
K OD, mm
L Length, mm
O
FF
TABLE 1 Continued
IP No. 23C
Name Saybolt Viscosity Reid Vapor Pressure Saybolt Viscosity
Range 19 to 27°C 66 to 80°F 34 to 42°C 94 to 108°F 49 to 57°C 120 to 134°F
G
For test at 21.1 and 25°C 70 and 77°FG 37.8°C G
100°FG 50 and 54.4°CG
122 and 130°FG
A Immersion, mm total total total
Graduations:
Subdivisions 0.1°C 0.2°F 0.1°C 0.2°F 0.1°C 0.2°F
Long lines at each 0.5°C 1°F 0.5°C 1°F 0.5°C 1°F
Numbers at each 1°C, except 21 2°F 1°C 2°F 1°C, except 54 2°F
17C-86 or 17F-86 18C-86 or 18F-86 19C-86 or 19F-86
Expansion chamber:
E 1 – 05
11
E Bulb OD, mm ≤5.0 and ≥stem ≥stem ≤5.0 and ≥stem

Scale location:
Ice-point scale:
Range
J Distance to top, max, mm 60H 60H 60H
Stem enlargement:
K OD, mm 8.0 to 10.0 8.0 to 10.0 8.0 to 10.0
L Length, mm 4.0 to 7.0 4.0 to 7.0 4.0 to 7.0
M Distance to bottom, mm 112 to 116 112 to 116 112 to 116
G
The test temperatures shall be indicated by an arrow whether the graduation corresponding to that point is numbered or not.
H
Long, narrow shape; mercury shall be in the chamber at 0°C (32°F).
O
FF
TABLE 1 Continued
IP No. 24C
Name Saybolt Viscosity Saybolt Viscosity Oxidation Stability
G
For test at 60°C 140°FG 82.2°C G
180°FG 98.9 and 100°C G
210°FG
Graduations:
Numbers at each 1°C 2°F 1°C, except 82 2°F 1°C 2°F
20C-86 or 20F-86 21C-86 or 21F–86 22C-86 or 22F–86
Expansion chamber:
E 1 – 05
12
Scale location:
Ice-point scale:
Range
H Bottom of bulb to ice-point,
mm
Stem enlargement:
K OD, mm 8.0 to 10.0 8.0 to 10.0 8.0 to 10.0
G
The test temperatures shall be indicated by an arrow whether the graduation corresponding to that point is numbered or not.
H
O
FF
TABLE 1 Continued
ASTM No. 23C-86 24C-86 25C-86
IP No.
Name Engler ViscosityI Engler ViscosityI Engler ViscosityI
Reference Fig. No. 7K 7K 7K
Range 18 to 28°C 39 to 54°C 95 to 105°C
For test at 25°C 40 and 50°C 100°C
Graduations:
Subdivisions 0.2°C 0.2°C 0.2°C
Long lines at each 1°C 1°C 1°C
Numbers at each 2°C full figures at 25 2°C full figures at 40 and 50 2°C full figures at 100
Scale error, max 0.1°C at 25°C 0.1°C at 40 and 50°C 0.1°C at 100°C
23C-86 24C-86 25C-86
90 MM IMMJ 90 MM IMMJ 90 MM IMMJ
Expansion chamber:
Permit heating to 100°C 105°C 155°C
E 1 – 05
13

Scale location:
Bottom of bulb to line at 18°C 39°C 95°C
Ice-point scale:
Range
J Distance to top, max, mm 60I 60I 60I
Stem enlargement:
K OD, mm
L Length, mm
I
The thermometer shall be made to be mounted in a brass ferrule consisting of a tubular bushing 8.0 mm in outside diameter with a flanged head approximately 12 mm in diameter so that the upper
extremity of the 8.0 mm diameter is located 90 mm from the bottom of the bulb.
J
To be marked on the glass stem at least 90 mm from the bottom of the bulb.
K
Glass button finish, see 6.2.1.
L
Long, narrow shape; mercury shall be near bottom of the chamber at 0°C.
O
TABLE 1 Continued
ASTM No. 26C-86 27C-86 28C-86 28F-86FF
IP No. 31C
Name Stability Test of Soluble Nitrocellulose Turpentine Distillation Kinematic ViscosityM
Range 130 to 140°C 147 to 182°C 36.6 to 39.4°C 97.5 to 102.5°F
For test at 134.5°C 37.8°C 100°F
A Immersion, mm total 76 total
Graduations:
Subdivisions 0.1°C 0.5°C 0.05°C 0.1°F
Long lines at each 0.5°C 1°C 0.1 and 0.5°C 0.5 and 1°F
Numbers at each 1°C and in full at 130, 135, 140 2°C from 148 1°C 1°F
Scale error, max 0.2°C 0.5°C 0.1°C 0.2°F
26C-86 27C-86 28C-86 or 28F-86
76 MM IMM
Expansion chamber:
Permit heating to 175°C 230°C 105°C 220°F
E 1 – 05
14
E Bulb OD, mm 6.0 to 7.0 4.0 to 5.5 ≥stem
Scale location:
Bottom of bulb to line at 134.5°C 147°C 36.6°C 97.5°F
Ice-point scale:
Range −0.3 to + 0.3°CO 31.5 to 32.5°FO
I Distance to bottom, min, mm 100
J Distance to top, max, mm 100I 40I 125
Stem enlargement:
K OD, mm
L Length, mm
I
Long, narrow shape; mercury shall be near bottom of the chamber at 0°C.
M
For kinematic viscosity thermometers, the ice-point reading shall be taken within 1 h after being at the test temperature for not less than 3 minutes. The ice-point reading shall be expressed to the nearest
0.01°C or 0.02°F and applied as explained in Test Method E 77, Section 13.
O
FF
TABLE 1 Continued
ASTM No. 29C-86 29F-86FF 30F-86FF 33C-86 33F-86FF
IP No. 34C 20C
Name Kinematic ViscosityM Kinematic ViscosityM Low Aniline Point
Range 52.6 to 55.4°C 127.5 to 132.5°F 207.5 to 212.5°F −38 to + 42°C −36.5 to + 107.5°F
For test at 54.4°C 130°F 210°F
A Immersion, mm total total 50
Graduations:
Subdivisions 0.05°C 0.1°F 0.1°F 0.2°C 0.5°F
Long lines at each 0.1 and 0.5°C 0.5 and 1°F 0.5 and 1°F 1°C 1°F
Numbers at each 1°C 1°F 1°F 2°C 5°F
Scale error, max 0.1°C 0.2°F 0.2°F 0.2°C 0.5°F
29C-86 or 29F–86 30F-86 33C-86 or 33F-86
50 MM IMM
Expansion chamber:
Permit heating to 105°C 220°F 266°F 100°C 212°F
E 1 – 05
15
E Bulb OD, mm ≥stem ≥stem ≤5.0 and ≥stem
Scale location:
Bottom of bulb to line at 52.6°C 127.5°F 207.5°F −35°C −31°F
Ice-point scale:
Range −0.3 to + 0.3°CO 31.5 to 32.5°FO 31.5 to 32.5°FO
I Distance to bottom, min, mm 100 100
J Distance to top, max, mm 125 125
Stem enlargement:
K OD, mm
L Length, mm
M
O
FF
TABLE 1 Continued
ASTM No. 34C-86 34F-86FF 35C-86 35F-86FF 36C-86
IP No. 21C 59C
Name Medium Aniline Point High Aniline Point Titer TestN
Range 25 to 105°C 77 to 221°F 90 to 170°C 194 to 338°F −2 to + 68°C
For test at
Graduations:
Subdivisions 0.2°C 0.5°F 0.2°C 0.5°F 0.2°C
Long lines at each 1°C 1°F 1°C 1°F 1°C
Numbers at each 2°C 5°F 2°C 5°F 2°C
Scale error, max 0.2°C 0.5°F 0.4°C 1.0°F 0.2°C
34C-86 or 34F-86 35C-86 or 35F–86 36C-86
Expansion chamber:
Permit heating to 150°C 302°F 220°C 428°F 85°CO
C Stem OD, mm 6.0 to 7.5 6.0 to 7.5 6.0 to 7.0Q
E 1 – 05
16
E Bulb OD, mm ≤5.0 and ≥stem 5.0 to ≥stem ≤5.5 and ≥stem
Scale location:
Bottom of bulb to line at 25°C 77°F 90°C 194°F −2°C
Ice-point scale:
Range
J Distance to top, max, mm 35P
Stem enlargement:
K OD, mm
L Length, mm
N
Thermometers made to these specifications conform also with the requirements for the titer test thermometer of the American Oil Chemists Society and the Association of Official Agricultural Chemists, except
for the special inscription.
O
P
Mercury shall be near middle of chamber at 0°C.
Q
The stem may be either the plain front or lens front type. If the thermometer is of the lens front type, the cross section of the stem shall be such that it will pass through an 8-mm ring gage but will not enter a
5-mm slot gage.
FF
TABLE 1 Continued
ASTM No. 37C-86 38C-86 39C-86
IP No. 77C 78C 79C
Name Solvents Distillation Solvents Distillation Solvents Distillation
Range −2 to + 52°C 24 to 78°C 48 to 102°C
For test at
Graduations:
Numbers at each 2°C 2°C 2°C
Scale error, max 0.2°C 0.2°C 0.2°C
37C-86 38C-86 39C-86
Expansion chamber:
E 1 – 05
17

E Bulb OD, mm ≥stem ≥stem ≥stem
Scale location:
Bottom of bulb to line at −2°C 24°C 48°C
Ice-point scale:
Range
J Distance to top, max, mm 35T
Stem enlargement:
K OD, mm
L Length, mm
O
T
Mercury shall be near the bottom of the chamber at 0°C.
TABLE 1 Continued
ASTM No. 40C-86 41C-86 42C-86
IP No. 80C 81C 82C
Range 72 to 126°C 98 to 152°C 95 to 255°C
For test at
Graduations:
Scale error, max 0.2°C 0.3°C 1°C
40C-86 41C-86 42C-86
Expansion chamber:
E 1 – 05
18

Scale location:
Bottom of bulb to line at
F Distance, mm 72°C 98°C 95°C
G Length of graduated portion, mm 125 to 145 125 to 145 125 to 145
190 to 235O 190 to 235O 190 to 235O
Ice-point scale:
Range
J Distance to top, max, mm 35T 35T 35T
Stem enlargement:
K OD, mm
L Length, mm
O
T
TABLE 1 Continued
IP No. 65C 29C 30C
Name Kinematic ViscosityM,R Kinematic ViscosityM Kinematic ViscosityM
Range −51.6 to − 34°C −61 to − 29°F 18.6 to 21.4°C 66.5 to 71.5°F 23.6 to 26.4°C 74.5 to 79.5°F
For test at 20°C 68 and 70°F 25°C 77°F
Graduations:
Long lines at each 0.5 and 1°C 1°F 0.1 and 0.5°C 0.5 and 1°F 0.1 and 0.5°C 0.5 and 1°F
Numbers at each 1°C starting at −51°C 2°F starting at − 60°F 1°C 1°F 1°C 1°F
43C-86 or 43F-86 44C-86 or 44F-86 45C-86 or 45F–86
MERC-THAL
Expansion chamber:
Permit heating to 105°CS 220°FS 105°C 220°F 105°C 220°F
E Bulb OD, mm 6.0 to 7.0 ≥stem ≥stem
E 1 – 05
19
Scale location:
Bottom of bulb to line at −51.6°C −61°F 18.6°C 66.5°F 23.6°C 74.5°F
Ice-Point scale:
Range −0.6 to + 0.6°CO 31 to 33°FO −0.3 to + 0.3°CO 31.5 to 32.5°FO −0.3 to + 0.3°CO 31.5 to 32.5°FO
I Distance to bottom, min, mm 290U 100 100
J Distance to top, max, mm 310U 125 125
Stem enlargement:
K OD, mm
L Length, mm
M
O
R
S
The expansion chamber shall be of the long narrow type 10 to 20 mm in length. The length of unchanged capillary between the nearest graduation mark and the expansion chamber shall be not less than 10
mm.
U
The length of unchanged capillary between the nearest graduation mark and contraction chamber shall be not less than 10 mm.
FF
TABLE 1 Continued
IP No. 66C 35C 90C
Name Kinematic ViscosityM Kinematic ViscosityM Kinematic ViscosityM
Range 48.6 to 51.4°C 119.5 to 124.5°F 58.6 to 61.4°C 137.5 to 142.5°F 80.6 to 83.4°C 177.5 to 182.5°F
For test at 50°C 122°F 60°C 140°F 82.2°C 180°F
Graduations:
Long lines at each 0.1 and 0.5°C 0.5 and 1°F 0.1 and 0.5°C 0.5 and 1°F 0.1 and 0.5°C 0.5 and 1°F
46C-86 or 46F–86 47C-86 or 47F–86 48C-86 or 48F–86
Expansion chamber:
E 1 – 05
20
Scale location:
Bottom of bulb to line at 48.6°C 119.5°F 58.6°C 137.5°F 80.6°C 177.5°F
Ice-point scale:
Range −0.3 to + 0.3°CO 31.5 to 32.5°FO −0.3 to + 0.3°CO 31.5 to 32.5°FO −0.3 to + 0.3°CO 31.5 to 32.5°FO
I Distance to bottom, min, mm 100 100 100
J Distance to top, max, mm 125 125 125
Stem enlargement:
K OD, mm
L Length, mm
M
O
FF
TABLE 1 Continued
ASTM No. 49C-86 50F-86FF 51F-86FF
IP No.
Name Stormer Viscosity Gas Calorimeter Inlet Gas Calorimeter Outlet
Range 20 to 70°C 54 to 101°F 69 to 116°F
For test at
Graduations:
Subdivisions 0.2°C 0.1°F 0.1°F
Long lines at each 1°C 0.5°F 0.5°F
Numbers at each 2°C 1°F 1°F
Scale error, max 0.2°C 0.2°FV 0.2°FV
49C-86 50F-86 51F-86
65 MM IMM
Expansion chamber:
Permit heating to 100°C 150°F 212°F
E 1 – 05
21
E Bulb OD, mm ≤5.0 and ≥stem 6.5 to 7.0 6.5 to 7.0
Scale location:
Bottom of bulb to line at 20°C 54°F 69°F
Ice-point scale:
Range
J Distance to top, max, mm 50P 43X 43X
Stem enlargement:
K OD, mm
L Length, mm
O
P
Mercury shall be near middle of chamber at 0°C.
V
Change in correction over any 5°F interval shall not exceed 0.10°F.
X
Mercury shall be in the chamber at 32°F.
FF
TABLE 1 Continued
ASTM No. 52C-86 54C-86 54F-86FF 56C-86 56F-86FF
IP No. 18C
Name Butadiene Boiling Point Range Congealing Point Bomb Calorimeter
Range −10 to + 5°C 20 to 100.6°C 68 to 213°F 19 to 35°C 66 to 95°F
For test at
Graduations:
Subdivisions 0.1°C 0.2°C 0.5°F 0.02°C 0.05°F
Long lines at each 0.5°C 1°C 1°F 0.1°C 0.1 and
0.5°F
Numbers at each 1°C 2°C 5°F 0.2°C 1°F
Scale error, max 0.1°C 0.2°C 0.5°F 0.10°CY 0.20°FZ
52C-86 54C–86 or 54F-86 56C–86 or 56F-86
Expansion chamber:
Permit heating to 100°CW 110°C 230°F 66°C 150°F
E 1 – 05
4.5 to 6.0MM 7.0 to 8.0BB
22
E Bulb OD, mm 5.5 to ≥stem

Scale location:
Bottom of bulb to line at −10°C 20°C 68°F 19°C 66°F
Ice-point scale:
Range
Stem enlargement:
K OD, mm
L Length, mm
O
W
Expansion chamber shall be of the long narrow type and there shall be not less than 10 mm of unchanged capillary between the base of the chamber and the top graduation.
Y
Over any interval of 2°C the change in correction shall not exceed 0.02°C.
Z
Over any interval of 4°F the change in correction shall not exceed 0.05°F.
BB
FF
MM
Bulb shape ellipsoidal (see Fig. 2).
TABLE 1 Continued
IP No.
Name Tag Closed Tester Low Range Tank Tank
Reference Fig. No. 5 4AA 4AA
Range −20 to + 50°C −4 to + 122°F −34 to + 49°C −30 to + 120°F −18 to + 82°C 0 to 180°F
For test at
Graduations:
Subdivisions 0.5°C 1°F 0.5°C 1°F 0.5°C 1°F
Scale error, max 0.5°C 1°F 0.3°C 0.5°F 0.3°C 0.5°F
57C-86 or 57F-86 58C-86 or 58F–86 59C-86 or 59F-86
57 MM IMM
Expansion chamber:
CC CC
C Stem OD, mm 6.0 to 7.0
E 1 – 05
23

Scale location:
Bottom of bulb to line at −20°C −4°F −34°C −30°F −18°C 0°F
Ice-point scale
Range
Stem enlargement:
K OD, mm 7.5 to 8.5
L Length, mm 2.5 to 5.0E
M Distance to bottom, mm 64 to 66
E
O
AA
CC
The stem shall be of the lens front type. The cross section of the stem shall be such that it will pass through a 8.0-mm ring gage but will not enter a 5.0-mm slot gage. A minor diameter of 4 mm is
permissible provided that the major diameter is not less than 7 mm.
FF
TABLE 1 Continued
IP No. 63C
Name Tank Petrolatum Melting Point Precision
Reference Fig. No. 4AA 7 4
Range 77 to 260°C 170 to 500°F 32 to 127°C 90 to 260°F −38 to + 2°C −36 to + 35°F
For test at
A Immersion, mm total 79 total
Graduations:
Subdivisions 1°C 2°F 0.2°C 0.5°F 0.1°C 0.2°F
Long lines at each 5°C 10°F 1°C 1°F 0.5°C 1°F
Scale error, max 0.5°C 1°F 0.2°C 0.5°F 0.1°C 0.2°F
60C-86 or 60F-86 61C-86 or 61F-86 62C-86 or 62F-86
79 MM IMM
Expansion chamber:
A
CC
C Stem OD, mm 6.0 to 8.0 7.0 to 8.0
D Bulb length, mm 15 to 25 18 to 28DD 25 to 35
E Bulb OD, mm ≥stem 5.0 to 6.0 6.0 to 7.0
E 1 – 05
24
Scale location:
Bottom of bulb to line at 77°C 170°F 32°C 90°F −35°C −31°F
Ice-point scale:
Range
Stem enlargement:
K OD, mm
L Length, mm
A
O
AA
CC
DD
Bulb bottom shall be essentially hemispherical.
FF
TABLE 1 Continued
FF
ASTM No. 63C-86 63F-86 64C-86 64F-86FF 65C-86 65F-86FF
IP No.
Name Precision Precision Precision
Range −8 to + 32°C 18 to 89°F 25 to 55°C 77 to 131°F 50 to 80°C 122 to 176°F
For test at
Graduations:
63C-86 or 63F–86 64C-86 or 64F-86 65C-86 or 65F–86
Expansion chamber:
E 1 – 05
25

Scale location:
Bottom of bulb to line at −5°C 23°F 25°C 77°F 50°C 122°F
Ice-point scale:
Range −0.5 to + 0.5°CO 31 to 33°FO −0.5 to + 0.5°CO 31 to 33°FO
H Bottom of bulb to ice-point, mm 60 to 70 60 to 70
Stem enlargement:
K OD, mm
L Length, mm
O
FF
TABLE 1 Continued
FF
ASTM No. 66C-86 66F-86 67C-86 67F-86FF 68C-86 68F-86FF
IP
Name Precision Precision Precision
For test at
Graduations:
Long lines at each 0.5°C 1°F 1°C 1°F 1°C 1°F
66C-86 or 66F-86 67C-86 or 67F-86 68C-86 or 68F-86
Expansion chamber:
E 1 – 05
26

Scale location:
Ice-point scale:
Range −0.5 to + 0.5°CO 31 to 33°FO −1 to + 1°CO 30 to 34°FO −1 to + 1°CO 30 to 34°FO
H Bottom of bulb to ice-point, mm 60 to 70 45 to 55 45 to 55
Stem enlargement:
K OD, mm
L Length, mm
O
FF
TABLE 1 Continued
IP No. 72C
Name Precision Precision Oil in Wax
C C
Range 195 to 305°C 383 to 581°F 295 to 405°C 563 to 761°F −37 to + 21°C −35 to + 70°F
For test at
A Immersion, mm total total 76
Graduations:
Subdivisions 0.5°C 1°F 0.5°C 1°F 0.5°C 1°F
Scale error, max 0.5°C 1°F 0.5°C 1°F 0.2°C 0.5°F
69C-86 or 69F-86 70C-86 or 70F-86 71C-86 or 71F-86
76 MM IMM
Expansion chamber:
A
E 1 – 05
27

Scale location:
Bottom of bulb to line at 195°C 383°F 295°C 563°F −37°C −35°F
Ice-point scale:
Range −2 to + 2°CO 27 to 37°FO −2 to + 2°CO 27 to 37°FO
H Bottom of bulb to ice-point, mm 52 to 62 52 to 62
Stem enlargement:
K OD, mm
L Length, mm
A
C
O
FF
TABLE 1 Continued
IP No. 67C 68C 69C
Name Kinematic ViscosityM Kinematic ViscosityM,R Kinematic ViscosityM,R
Range −19.4 to − 16.6°C −2.5 to + 2.5°F −41.4 to − 38.6°C −42.5 to − 37.5°F −55.4 to − 52.6°C −67.5 to − 62.5°F
For test at −17.8°C 0°F −40°C −40°F −53.9°C −65°F
Graduations: 0.05°C 0.1°F 0.05°C 0.1°F 0.05°C 0.1°F
Long lines at each 0.1 and 0.5°C 0.5 and 1°F 0.1 and 0.5°C 0.5 and 1°F 0.1 and 0.5°C 0.5 and 1°F
72C-86 or 72F-86 73C-86 or 73F-86 74C-86 or 74F-86
MERC-THAL MERC-THAL
Expansion chamber:
E 1 – 05
28

Scale location:
Bottom of bulb to line at −19.4°C −2.5°F −41.4°C −42.5°F −55.4°C −67.5°F
Ice-point scale:
Range −0.3 to + 0.3°CO 31.5 to 32.5°FO −0.3 to + 0.3°CO 31.5 to 32.5°FO −0.3 to + 0.3°CO 31.5 to 32.5°FO

Stem enlargement:
K OD, mm
L Length, mm
O
M
R
FF
TABLE 1 Continued
ASTM No. 75F-86FF 76F-86FF 77F-86FF
IP No.
Name Coolant (Antifreeze) Freezing Point Coolant (Antifreeze) Freezing PointR Saybolt Viscosity
Range −35 to + 35°F −65 to + 5°F 245 to 265°F
For test at 250°FG
A Immersion, mm 100 100 total
Graduations:
Subdivisions 0.5°F 0.5°F 0.5°F
Long lines at each 1°F 1°F 1°F
Numbers at each 5°F 5°F 5°F
Scale error, max 0.5°F 1°F 0.5°F
75F-86 76F-86 77F-86
MERC-THAL
Expansion chamber:
Permit heating to 140°F 140°F 315°F
E 1 – 05
29
E Bulb OD, mm 5.0 to 6.0 5.0 to 6.0 <5.0 and >stem
Scale location:
Bottom of bulb to line at −35°F −65°F 245°F
Ice-point scale:
Range
J Distance to top, max, mm 60H
Stem enlargement:
K OD, mm 8.0 to 10.0
L Length, mm 4.0 to 7.0
G
H
O
R
FF
TABLE 1 Continued
ASTM No. 78F-86FF 79F-86FF 80F-86FF
IP No.
Name Saybolt Viscosity Saybolt Viscosity Saybolt Viscosity
Range 295 to 315°F 345 to 365°F 395 to 415°F
For test at 300°FG 350°FG 400°FG
Graduations:
Subdivisions 0.5°F 0.5°F 0.5°F
Long lines at each 1°F 1°F 1°F
Numbers at each 5°F 5°F 5°F
Scale error, max 0.5°F 0.5°F 0.5°F
78F-86 79F-86 80F-86
Expansion chamber:
Permit heating to 365°F 415°F 465°F
E 1 – 05
30
Scale location:
Bottom of bulb to line at 295°F 345°F 395°F
Ice-point scale:
Range
Stem enlargement:
K OD, mm 8.0 to 10.0 8.0 to 10.0 8.0 to 10.0
G
H
O
FF
TABLE 1 Continued
ASTM No. 81F-86FF 82C-86 82F-86FF 83C-03 83F-03FF
IP No.
Name Saybolt Viscosity Fuel Rating Engine Fuel Rating Air-Low
Range 445 to 465°F −15 to + 105°C 0 to 220°F 15 to 70°C 60 to 160°F
For test at 450°FG 51.7°C and 65.6°CG
125°Fand
150°FG
A Immersion, mm total 30EE 40EE
Graduations:
Subdivisions 0.5°F 1°C 2°F 1°C 1°F
Long lines at each 1°F 5°C 10°F 5°C 5°F
Numbers at each 5°F 10°C 20°F 10°C 10°F
Scale error, max 0.5°F 1°C 2°F 1°C 2°F
81F-86 82C-86 or 82F-86 83C-03 or 83F-03
30 MM IMM 40 MM IMM
Expansion chamber:
Permit heating to 515°F 125°C 260°F 100°C 215°F
E 1 – 05
31
E Bulb OD, mm ≤5.0 and ≥stem 5.0 to 6.5 5.0 to 6.5
Scale location:
Bottom of bulb to line at 445°F −15°C 0°F 15°C 60°F
Ice-point scale:
Range
J Distance to top, max, mm 60H
Stem enlargement:
K OD, mm 8.0 to 10.0 8.0 to 9.0 8.0 to 9.0
G
H
O
EE
FF
TABLE 1 Continued
IP No.
Name Fuel Rating, Orifice Tank Fuel Rating, Surge Fuel Rating, Mix
G
For test at 51.7°C 125°FG 107.2°CG
225°FG 104.4°C and 220°F and
148.9°CG 300°FG
A Immersion, mm 249EE 181EE 35EE
Graduations:
Scale error, max 1°C 2°F 1°C 2°F 1°C 2°F
84C-86 or 84F-86 85C-86 or 85F-86 86C-86 or 86F-86
Expansion chamber:
E 1 – 05
32

Scale location:
Ice-point scale:
Range
Stem enlargement:
K OD, mm 8.0 to 9.0 8.0 to 9.0 8.0 to 9.0
L Length, mm
O
EE
FF
TABLE 1 Continued
IP No.
Name Fuel Rating Coolant Vegetable Oil Flash Solidification Point
Range 150 to 205°C 300 to 400°F 10 to 200°C 50 to 392°F −20 to + 10°C
G
For test at 190.6°C 375°FG
A Immersion, mm 40EE 57 76
Graduations:
Subdivisions 1°C 1°F 1°C 2°F 0.1°C
Long lines at each 5°C 5°F 5°C 10°F 0.5°C
Numbers at each 10°C 10°F 10°C 20°F 1.0°C
Scale error, max 1°C 2°F 1°C 2°F 0.1°C
87C-86 or 87F-86 88C-86 or 88F-86 89C-86
Expansion chamber:
Permit heating to 225°C 440°F 250°C 490°F 60°C
E 1 – 05
33
E Bulb OD, mm 5.0 to 6.5 ≥stem ≤5.0 and ≥stem
Scale location:
Bottom of bulb to line at 150°C 300°F 10°C 50°F −20°C
Ice-point scale:
Range
Stem enlargement:
K OD, mm 8.0 to 9.0 7.5 to 8.5E
E
O
EE
FF
TABLE 1 Continued
ASTM No. 90C-86 91C-86 92C-86
IP No.
Name Solidification Point Solidification Point Solidification Point
Range 0 to 30°C 20 to 50°C 40 to 70°C
For test at
Graduations:
Long lines at each 0.5°C 0.5°C 0.5°C
Numbers at each 1.0°C 1.0°C 1.0°C
90C-86 91C-86 92C-86
Expansion chamber:
E 1 – 05
34

Scale location:
Ice-point scale:
Range
Stem enlargement:
K OD, mm
L Length, mm
O
TABLE 1 Continued
ASTM No. 93C-86 94C-86 95C-86
IP No.
Name Solidification Point Solidification Point Solidification Point
Range 60 to 90°C 80 to 110°C 100 to 130°C
For test at
Graduations:
Long lines at each 0.5°C 0.5°C 0.5°C
Numbers at each 1.0°C 1.0°C 1.0°C
93C-86 94C-86 95C-86
Expansion chamber:
E 1 – 05
35

Scale location:
Ice-point scale:
Range
Stem enlargement:
K OD, mm
L Length, mm
O
TABLE 1 Continued
IP No.
Name Solidification Point Tank Tank
Reference Fig. No. 7 4AA 4AA
Range 120 to 150°C −18 to + 49°C 0 to 120°F 16 to 82°C 60 to 180°F
For test at
Graduations:
Subdivisions 0.1°C 0.5°C 1°F 0.5°C 1°F
Long lines at each 0.5°C 1°C 5°F 1°C 5°F
Numbers at each 1.0°C 5°C 10°F 5°C 10°F
Scale error, max 0.2°C 0.3°C 0.5°F 0.3°C 0.5°F
96C-86 97C-86 or 97F-86 98C-86 or 98F-86
76 MM 1MM
Expansion chamber:
Permit heating to 190°C 100°C 212°F 100°C 212°F
CC CC
C Stem OD, mm 6.0 to 7.0
E 1 – 05
36
E Bulb OD, mm ≤5.0 and ≥stem ≥stem ≥stem
Scale location:
Bottom of bulb to line at 120°C −18°C 0°F 16°C 60°F
Ice-point scale:
Range
Stem enlargement:
K OD, mm
L Length, mm
O
AA
CC
FF
TABLE 1 Continued
ASTM No. 99C-92 99F-86FF 100C-86 101C-86
IP No.
Name Weathering TestR Solidification Point Solidification Point
Reference Fig. No. 3AA 7 7
Range −50 to + 5°C −58 to + 41°F 145 to 205°C 195 to 305°C
For test at
GG
Graduations:
Subdivisions 0.2°C 0.5°F 0.2°C 0.5°C
Long lines at each 1°C 1°F 1°C 1°C
Numbers at each 2°C 5°F 2°C 5°C
Scale error, max 0.2°C 0.4°F 0.4°C 1.0°C
99C-92 or 99F–86 100C-86 101C–86
MERC-THAL
Expansion chamber:
Permit heating to Elongated type Elongated type 150°F 250°C 330°C
66°C
C Stem OD, mm 6.5 to 8.0HH 6.0 to 7.0 6.0 to 7.0
E 1 – 05
37
E Bulb OD, mm 6.0 to 7.0 ≤5.0 and ≥stem ≤5.0 and ≥stem
Scale location:
Bottom of bulb to line at −50°C −58°F 145°C 195°C
Ice-point scale:
Range
I Contraction chamber:
Distance to bottom, min, mm
K Stem enlargement:
OD, mm
L Length, mm
O
R
A suitable mecury-thallium alloy shall be used as the actuating liquid.
AA
FF
GG
The immersion line shall be visible in the case opening after assembly. The immersion shall be measured from the bottom of the bulb rather than from the bottom of the armor. See 6.2.2.
HH
The stem shall be either the round or lens-front type.
TABLE 1 Continued
ASTM No. 102C-86 103C-86 104C-86
IP No. 83C 84C 85C
Range 123 to 177°C 148 to 202°C 173 to 227°C
For test at
Graduations:
102C-86 103C-86 104C-86
Expansion chamber:
E 1 – 05
38

Scale location:
F Bottom of bulb to line at 123°C 148°C 173°C
G Distance, mm 125 to 145 125 to 145 125 to 145
Length of graduated portion, mm 190 to 235O 190 to 235O 190 to 235O
Ice-point scale:
Range
Stem enlargement:
K OD, mm
L Length, mm
O
T
TABLE 1 Continued
ASTM No. 105C-86 106C-86 107C-86
IP No. 86C 87C 88C
Range 198 to 252°C 223 to 277°C 248 to 302°C
For test at
Graduations:
105C-86 106C-86 107C-86
Expansion chamber:
E 1 – 05
39

Scale location:
Ice-point scale:
Range
Stem enlargement:
K OD, mm
L Length, mm
O
T
TABLE 1 Continued
ASTM No. 108F-86FF 109F-86FF 110C-86 110F-86FF
IP No. 93C
Name Saybolt Viscosity Saybolt Viscosity Kinematic ViscosityM
Range 270 to 290°F 320 to 340°F 133.6 to 136.4°C 272.5 to 277.5°F
For test at 275°FG 325°FG 135°C 275°F
Graduations:
Subdivisions 0.5°F 0.5°F 0.05°C 0.1°F
Long lines at each 1°F 1°F 0.1 and 0.5°C 0.5 and 1°F
Numbers at each 5°F 5°F 1°C 1°F
Scale error, max 0.5°F 0.5°F 0.15°C 0.3°F
108F-86 109F-86 110C-86 or 110F-86
Expansion chamber:
Permit heating to 340°F 390°F 170°C 350°F
E 1 – 05
40
E Bulb OD, mm ≤5.0 and ≥stem ≤5.0 and ≥stem ≥stem

Scale location:
Bottom of bulb to line at 270°F 320°F 133.6°C 272.5°F
Ice-point scale:
Range –0.3 to +0.6°C 31.5 to 33.0°FO
J Distance to top, max, mm 60H 60H 125
Stem enlargement:
K OD, mm 8.0 to 10.0 8.0 to 10.0
L Length, mm 4.0 to 7.0 4.0 to 7.0
G
H
M
For kinematic viscosity thermometers, the ice-point reading shall be taken within 1 h after being at the test temperature for not less than 3 minutes. The ice-point
reading shall be expressed to the nearest 0.01°C or 0.02°F and applied as explained in Test Method E 77, Section 13.
O
FF
For Fahrenheit thermometers, dimension G (length of graduated portion) shall be measured as the length of graduated portion corresponding to the nominal Celsius
range.
TABLE 1 Continued
ASTM No. 111C-86 112C-86 113C-86 113F-86FF
IP No. 89C
Name Tar Acids Distillation Solidification Point of Benzene Softening Point (Bitumen) Wide Range
Range 170 to 250°C 4 to 6°C −1 to + 175°C 30 to 350°F
For test at 5.4°C
Graduations:
Subdivisions 0.2°C 0.02°C 0.5°C 1°F
Long lines at each 1°C 0.1°C 1°C 5°F
Numbers at each 2°C 0.2°C 5°C 10°F
Scale error, max 0.4°C to 225°C 0.04°C 0.5°C 1°F
0.6°C above 225°C
111C-86 112C-86 113C-86 or 113F-86
100 MM IMM
Expansion chamber:
E 1 – 05
41

E Bulb OD, mm 6.0 to 7.0 6.0 to ≥stem 4.5 to 5.5
Scale location:
Bottom of bulb to line at 170°C 4°C 0°C 32°F
Ice-point scale:
Range −0.2 to + 0.2°CO
H Bottom of bulb to ice-point, mm 60 to 70
J Distance to top, max, mm 35 90II
Stem enlargement:
K OD, mm
L Length, mm
II
Contraction chamber to be long narrow type.
O
FF
TABLE 1 Continued
ASTM No. 114C-86 115C-86 116C-86 117C-86
IP No. 14C
Name Aviation Fuel Freezing PointB See Table 5 Bomb Calorimeter Bomb Calorimeter
Reference Fig. No. 4 9 and 14 9 and 14
Range −80 to + 20°C 18.9 to 25.1°C 23.9 to 30.1°C
For test at
Graduations:
Long lines at each 1°C 0.05°C 0.05°C
Numbers at each 5°C 0.1°C 0.1°C
Scale error, max 1°C 0.1°CJJ 0.1°CJJ
114C-86 116C-86 117C-86
Expansion chamber:
KK KK
D Bulb length, mm 8 to 16
E Bulb OD, mm ≥stem 7.0 to 8.2BB 7.0 to 8.2BB
E 1 – 05
42
Scale location:
Bottom of bulb to line at −80°C 19°C 24°C
Ice-point scale:
Range
Stem enlargement:
K OD, mm
L Length, mm
B
O
BB
JJ
Over any interval of 1°C the change in correction shall not exceed 0.01°C. The correction at the lowest temperature of the nominal range shall not change by more than 0.02°C immediately after the
thermometer has been heated for 15 min at a temperature 30°C higher, and allowed to cool naturally in air.
KK
The capillary bore shall be large enough in relation to the bulb to ensure that (without tapping) jumping of the meniscus does not exceed one half of the smallest scale division, when the temperature is
rising at a uniform rate not exceeding 0.05°C/min.
TABLE 1 Continued
IP No. 92C
Name Kinematic ViscosityM Coolant (Antifreeze) Kinematic
Freezing Point ViscosityM
Range 28.6 to 31.4°C 83.5 to 88.5°F −38.3 to − 30°C −37 to − 22°F 38.6 to 41.4°C
For test at 30°C 86°F 40°C
A Immersion, mm total 100LL total
Graduations:
Subdivisions 0.05°C 0.1°F 0.1°C 0.2°F 0.05°C
Long lines at each 0.1 and 0.5°C 0.5 and 1°F 0.5°C 1°F 0.1 and 0.5°C
Scale error, max 0.1°C 0.2°F 0.2°C 0.4°F 0.1°C

118C-86 or 118F-86 119C-86 or 119F-86 120C-86
100 MM IMM
Expansion chamber:
E 1 – 05
43

E Bulb OD, mm ≥stem 5.0 to ≥stem ≥stem
Scale location:
Bottom of bulb to line at 28.6°C 83.5°F −38.3°C −37°F 38.6°C
Ice-point scale:
Range −0.3 to + 0.3°CO 31.5 to 32.5°FO −0.5 to + 0.5°CO 31 to 33°FO −0.3 to + 0.3°CO
H Bottom of bulb to ice-point, mm 370 to 390
Stem enlargement:
K OD, mm
L Length, mm
M
O
FF
II
The thermometer is to be calibrated for 100-mm immersion for the main scale, the ice point is to be calibrated for total immersion.
TABLE 1 Continued
ASTM No. 121C-86 122C-86 123C-86
IP No. 32C 94C 95C
Name Kinematic ViscosityM Brookfield ViscosityR Brookfield Viscosity
Ref. Fig. No. 6 4 4
Range 98.6 to 101.4°C –45 to –35°C –35 to –25°C
For Test at 98.9 and 100°C 150°C
Graduations:
Long Lines at each 0.1 and 0.5°C 0.5°C 0.5°C
121C-86 122C-86 123C-86
MERC-THAL
Expansion chamber:
E 1 – 05
44
Scale location:
Bottom of bulb to line at 98.6°C –45°C –35°C
Ice-point scale:
Range –0.3 to +0.3°CO
Stem enlargement:
K OD, mm
L Length, mm
M
O
R
A suitable mecury-thallium alloy shall be used as the actuating liquid.
TABLE 1 Continued
ASTM No. 124C-86 125C-86 126C-86 126F-86FF
IP No. 96C 97C 71C
Name Brookfield Viscosity Brookfield Viscosity Kinematic ViscosityM
Range −25 to − 15°C −15 to − 5°C −27.4 to − 24.6°C −17.5 to − 12.5°F
For test at −26.1°C −15°F
Graduations:
Subdivisions 0.1°C 0.1°C 0.05°C 0.1°F
Long lines at each 0.5°C 0.5°C 0.1 and 0.5°C 0.5 and 1°F
Numbers at each 1°C 1°C 1°C 1°F
Scale error, max 0.2°C 0.2°C 0.1°C 0.2°F
124C-86 125C-86 126C-86 or 126F-86
Expansion chamber:
E 1 – 05
45
Scale location:
Bottom of bulb to line at −25°C −15°C −27.4°C −17.5°F
Ice-point scale:
Range −0.3 to + 0.3°CO 31.5 to 32.5°FO
Stem enlargement:
K OD, mm
L Length, mm
M
O
FF
TABLE 1 Continued
IP No. 99C 33C 36C
Name Kinematic ViscosityM Kinematic ViscosityM Kinematic ViscosityM
Ref. Fig. No. 10 4 6
Range −21.4 to − 18.6°C −1.4 to + 1.4°C 29.5 to 34.5°F 91.6 to 94.4°C 197.5 to 202.5°F
For Test at −20°C 0°C 32°F 93.3°C 200°F
Graduations:
Subdivisions 0.05°C 0.05°C 0.1°F 0.05°C 0.1°F
Long Lines at each 0.1 and 0.5°C 0.1 and 0.5°C 0.5 and 1°F 0.1 and 0.5°C 0.5 and 1°F
Numbers at each 1°C 1°C 1°F 1°C 1°F
Scale error, max 0.1°C 0.1°C 0.2°F 0.1°C 0.2°F
127C-86 128C-86 or 128F-86 129C-86 or 129F-86
Expansion chamber:
Permit heating to 105°C 105°C 220°F 120°C 250°F
E 1 – 05
46
Scale location:
Bottom of bulb to line at −21.4°C −1.4°C 29.5°F 91.6°C 197.5°F
Ice-point scale:
Range −0.3 to + 0.3°CO −0.3 to + 0.3°CO 31.5 to 32.5°FO
Stem enlargement:
K OD, mm
L Length, mm
M
O
Capillary clearance shall conform to Section 8.
FF
TABLE 1 Continued
ASTM No. 130C-90 130F-90FF 132C-95 133C-01 134C-03
IP No. 102C 37C
Name Tank Kinematic ViscosityM Precision Sludge
Ref. Fig. No. 4AA 6 3 3
Range −7 to + 105°C 20 to 220°F 148.6 to 151.4°C –38 to +2°C 144 to 156°C
For Test at 150°C 150°C
A Immersion, mm total total 76 100
Graduations:
Subdivisions 0.5°C 1°F 0.05°C 0.1°C 0.2°C
Long Lines at each 1°C 5°F 0.1 and 0.5°C 0.5°C 1°C
Numbers at each 5°C 10°F 1°C 1°C 2°C
Scale error, max 0.5°C 1°F 0.20°C 0.1°C 0.2°C
Special inscription ASTM ASTM ASTM ASTM
130C-90 or 130F–90 132C–95 133C-01 134C-03
Expansion chamber:
Permit heating to 125°C 257°F 185°C 55°C required
B Total length, mm 300 to 305 300 to 310 374 to 384 260 to 280
C Stem OD, mm cc 6.0 to 8.0 7.0 to 8.0 5.0 to 8.0
D Bulb length, mm 15 to 25 45 to 55 25 to 35 10 to 25
E 1 – 05
47
E Bulb OD, mm ≥stem ≥stem ≥stem ≥stem

Scale location:
Bottom of bulb to line at 0°C 32°F 148.6°C -38°C 150°C
F Distance, mm 76 to 93 160 to 180 115 to 135 170 to 210
G Length of graduated portion, mm 175 to 210O 40 to 90°CO 190 to 230O 50 to 80O
Ice-point scale:
Range −0.3 to + 0.6°CO
Contraction chamber: required
Stem enlargement:
K OD, mm
L Length, mm
AA
CC
The stem shall be of the lens front type. The cross section of the stem shall be such that it will pass through a 8.0-mm ring gage but
will not enter a 5.0-mm slot gage. A minor diameter of 4-mm is permissible provided that the major diameter is not less than 7 mm.
O
FF
For Fahrenheit thermometers, dimension G (length of graduated portion) shall be measured as the length of graduated portion
corresponding to the nominal Celsius range.
TABLE 1 Continued
IP No.
Name Fuel Rating Air-High Aviation Fuel Density Oxidation Cell Test
Ref. Fig. No. 11 4 3
Range 38 to 93°C 100 to 200°F –20 to +60°C –5 to +140°F 80 to 100°C
For Test at 51.7°CG 125°FG
A Immersion, mm 40EE total 76
Graduations:
Subdivisions 1°C 1°F 0.2°C 0.5°F 0.1°C
Long Lines at each 5°C 5°F 1°C 1°F 0.5°C
Scale error, max 1°C 2°F 0.15°C 0.25°F 0.1°C
135C-03 or 135F–03 136C-03 or 136F–03 137C-03
40 MM IMM 76 MM IMM
Expansion chamber:
OO
C Stem OD, mm 6.0 to 7.0 6.0 to 8.0
E 1 – 05
48
E Bulb OD, mm 5.0 to 6.5 bulb size ≥ stem size $6.0 and #stem
Scale location:
Bottom of bulb to line at 38°C 100°F –20°C –4°F 80°C
G Length of graduated portion, mm 64 to 81O 200 to 230O 115 to 125
Ice-point scale:
Range
Stem enlargement:
K OD, mm 8.0 to 9.0
L Length, mm
AA
CC
The stem shall be of the lens front type. The cross section of the stem shall be such that it will pass through a 8.0-mm ring gage but will not enter a 5.0-mm slot gage. A minor
diameter of 4-mm is permissible provided that the major diameter is not less than 7 mm.
O
FF
E 1 – 05
TABLE 2 Alphabetical List of ASTM Thermometers Covered by Specification E 1
NOTE 1—The specifications appear in numeric sequence in this standard.

Thermometer No. Thermometer No.
Thermometer Name Thermometer Name
°C °F °C °F
Aviation fuel density 136C 136F ... ...
Aviation fuel freezing point 114C ... 3C 3F
Bomb calorimeter 56C 56F Petrolatum melting point 61C 61F
116C ... Precision 62C 62F
117C ... 63C 63F
Brookfield Viscosity 122C ... 64C 64F
123C ... 65C 65F
124C ... 66C 66F
125C ... 67C 67F
Butadiene boiling point range 52C ... 68C 68F
Cleveland open flash 11C 11F 69C 69F
Cloud and pour 5C 5F 70C 70F
... ... 133C ...
Cloud and pour, low 6C 6F Reid vapor pressure 18C 18F
Congealing point 54C 54F Saybolt viscosity 17C 17F
Coolant (antifreeze) freezing point ... 75F 18C 18F
... 76F 19C 19F
119C 119F 20C 20F
Density wide range 12C 12F 21C 21F
Enclosed scale 115C ... 22C 22F
Engler viscosity 23C ... ... 77F
24C ... ... 78F
25C ... ... 79F
Fuel rating 82C 82F ... 80F
83C 83F ... 81F
84C 84F ... 108F
85C 85F ... 109F
... ... Sludge 134C ...
86C 86F Softening point (bitumen) wide-range 113C 113F
87C 87F Solidification point 89C ...
135C 135F ... ...
Gas calorimeter, inlet ... 50F 90C ...
Gas calorimeter, outlet ... 51F 91C ...
General purpose—see partial immersion; precision 92C ...
Gravity 12C 12F 93C ...
High aniline point 35C 35F 94C ...
High distillation 8C 8F 95C ...
High Pensky Martens 10C 10F 96C ...
High softening point 16C 16F 100C ...
Kinematic viscosity 28C 28F 101C ...
29C 29F Solidification point of benzene 112C ...
... 30F Solvents distillation 37C ...
43C 43F 38C ...
44C 44F 39C ...
45C 45F 40C ...
46C 46F 41C ...
47C 47F 42C ...
48C 48F 102C ...
72C 72F 103C ...
73C 73F 104C ...
74C 74F 105C ...
110C 110F 106C ...
118C 118F 107C ...
120C ... Stability test of soluble nitrocellulose 26C ...
121C ... Stormer viscosity 49C ...
126C 126F Tag closed tester, low range 57C 57F
127C ... Tag closed tester, high range 9C 9F
128C 128F Tank 58C 58F
129C 129F 59C 59F
132C
Loss on heat 13C ... 60C 60F
Low aniline point 33C 33F 97C 97F
Low cloud and pour 6C 6F 98C 98F
Low distillation 7C 7F 130C 130F
Low Pensky Martens 9C 9F Tar acids distillation 111C ...
Low softening point 15C 15F Titer test 36C ...
Medium aniline point 34C 34F Turpentine distillation 27C ...
Oil in wax 71C 71F Vegetable oil flash 88C 88F
Oxidation cell test 137C ... ... ...
49
E 1 – 05
Thermometer No. Thermometer No.

Thermometer Name Thermometer Name
°C °F °C °F
Oxidation stability 22C 22F Wax melting point 14C 14F
Partial immersion (general use) 1C 1F Weathering test 99C 99F
2C 2F
TABLE 3 List of ASTM Thermometers by Temperature Range
Scale ASTM Scale ASTM

Celsius (Centigrade) Immersion, Fahrenheit Immersion,
Error, Thermometer Error, Thermometer
Range mm Range mm
max Number max Number
Graduated in 0.01°C
18.9 to 25.1°C total 0.1 116C ... ... ... ...
23.9 to 30.1°C total 0.1 117C ... ... ... ...
Graduated in 0.02°C Graduated in 0.05°F
4 to 6°C total 0.04 112C ... ... ... ...
19 to 35°C total 0.10 56C 66 to 95°F total 0.20 56F
−55.4 to −52.6°C total 0.1 74C −67.5 to −62.5°F total 0.2 74F
−21.4 to −18.6°C total 0.1 127C ... ... ... ...
−19.4 to −16.6°C total 0.1 72C −2.5to +2.5°F total 0.2 72F
−1.4 to +1.4°C total 0.1 128C 29.5to 34.5°F total 0.2 128F
... ... ... ... 54 to 101°F total 0.2 50F
18.6 to 21.4°C total 0.1 44C 66.5 to 71.5°F total 0.2 44F
... ... ... ... 69 to 116°F total 0.2 51F
38.5 to 41.5°C total 0.1 120C ... ... ... ...
... ... ... ... 207.5 to 212.5°F total 0.2 30F
98.6 to 101.4°C total 0.1 121C ... ... ... ...
148.6 to 151.4°C total 0.20 132C
−51.6 to −34°C total 0.1 43C −61 to −29°F total 0.2 43F
−45 to −35°C total 0.4 122C ... ... ... ...
−38.3 to −30°C 100 0.2 119C −37 to −22°F 100 0.4 119F
−38 to +2°C total 0.1 62C −36 to +35°F total 0.2 62F
–38 to +2°C 76 mm 0.1 133C
−35 to −25°C total 0.4 123C ... ... ... ...
−25 to −15°C total 0.2 124C ... ... ... ...
−15 to −5°C total 0.2 125C ... ... ... ...
−20 to +10°C 76 0.1 89C ... ... ... ...
−10 to +5°C total 0.1 52C ... ... ... ...
−8 to +32°C total 0.1 63C 18 to 89°F total 0.2 63F
0 to 30°C 76 0.1 90C ... ... ... ...
20 to 50°C 76 0.1 91C ... ... ... ...
38 to 82°C 79 0.1 14C 100 to 180°F 79 0.2 14F
40 to 70°C 76 0.1 92C ... ... ... ...
60 to 90°C 76 0.1 93C ... ... ... ...
80 to 100°C 76 0.1 137C ... ... ... ...
80 to 110°C 76 0.1 94C ... ... ... ...
100 to 130°C 76 0.2 95C ... ... ... ...
120 to 150°C 76 0.2 96C ... ... ... ...
130 to 140°C total 0.2 26C ... ... ... ...
50
E 1 – 05
TABLE 3 Continued
Range mm Range mm
... ... ... ... −65 to +5°F 100 1 76F
−50 to +5°C 35 0.2 99C −55 to +40°F 35 0.4 99F
−38 to +42°C 50 0.2 33C −36.5 to +107.5°F 50 0.5 33F
... ... ... ... −35 to +35°F 100 0.5 75F
−2 to +52°C 100 0.2 37C ... ... ... ...
−2 to +68°C 45 0.2 36C ... ... ... ...
18 to 28°C 90 0.1 23C ... ... ... ...
20 to 70°C 65 0.2 49C ... ... ... ...
20 to 100.6°C total 0.2 54C 68 to 213°F total 0.5 54F
24 to 78°C 100 0.2 38C ... ... ... ...
25 to 105°C 50 0.2 34C 77 to 221°F 50 0.5 34F
32 to 127°C 79 0.2 61C 90 to 260°F 79 0.5 61F
39 to 54°C 90 0.1 24C ... ... ... ...
48 to 102°C 100 0.2 39C ... ... ... ...
72 to 126°C 100 0.2 40C ... ... ... ...
90 to 170°C 50 0.4 35C 194 to 338°F 50 1 35F
95 to 105°C 90 0.1 25C ... ... ... ...
98 to 152°C 100 0.3 41C ... ... ... ...
... ... ... ... 245 to 265°F total 0.5 77F
123 to 177°C 100 0.3 102C ... ... ... ...
... ... ... ... 270 to 290°F total 0.5 108F
144 to 156°C 100 0.2 134C 295 to 315°F total 0.5 78F
145 to 205°C 76 0.4 100C ... ... ... ...
148 to 202°C 100 0.4 103C ... ... ... ...
... ... ... ... 320 to 340°F total 0.5 109F
A
170 to 250°C 100 111C ... ... ... ...
173 to 227°C 100 0.4 104C ... ... ... ...
... ... ... ... 345 to 365°F total 0.5 79F
198 to 252°C 100 0.6 105C ... ... ... ...
... ... ... ... 395 to 415°F total 0.5 80F
... ... ... ... 445 to 465°F total 0.5 81F
223 to 277°C 100 0.8 106C ... ... ... ...
248 to 302°C 100 1 107C ... ... ... ...
Graduated in 0.5°C Graduated in 1°F
−80 to +20°C total 1 114C ... ... ... ...
−37 to +21°C 76 0.2 71C −35 to +70°F 76 0.5 71F
−20 to +50°C 57 0.5 57C −4 to +122°F 57 1 57F
−7 to +105°C total 0.5 130C 20 to 220°F total 1 130F
−5 to +110°C 57 0.5 9C 20 to 230°F 57 1 9F
−1 to +175°C total 0.5 113C 30 to 350°F total 1 113F
... ... ... ... 60 to 160°F 40 2 83F
... ... ... ... 75 to 175°F 249 2 84F
95 to 255°C 100 1 42C 100 to 200°F 40 2 135F
147 to 182°C 76 0.5 27C ... ... ... ...
155 to 170°C total 0.5 13C ... ... ... ...
... ... ... ... 300 to 400°F 40 2 87F
195 to 305°C total 0.5 69C 383 to 581°F total 1 69F
195 to 305°C 76 1 101C ... ... ... ...
295 to 405°C total 0.5 70C 563 to 761°F total 1 70F
Graduated in 1°C Graduated in 2°F
B C
−80 to +20°C 76 6C −112 to +70°F 76 6F
−38 to +50°C 108 0.5 5C −36 to +120°F 108 1 5F
−15 to +105°C 30 1 82C 0 to 220°F 30 2 82F
−20 to +150°C 76 0.5 1C 0 to 302°F 76 1 1F
−5 to +300°C 76 1 2C 20 to 580°F 76 2 2F
D E
−5 to +400°C 76 3C 20 to 760°F 76 3F
F G
−2 to +300°C total 7C 30 to 580°F total 7F
H I
−2 to +400°C total 8C 30 to 760°F total 8F
10 to 200°C 57 1 88C 50 to 392°F 57 2 88F
51
E 1 – 05
TABLE 3 Continued
Range mm Range mm
15 to 70°C 40 1 83C ... ... ... ...
25 to 80°C 249 1 84C ... ... ... ...
38 to 93°C 40 1 135C ... ... ... ...
40 to 150°C 181 1 85C 100 to 300°F 181 2 85F
77 to 260°C total 1 60C 170 to 500°F total 1 60F
95 to 175°C 35 1 86C 200 to 350°F 35 2 86F
150 to 205°C 40 1 87C ... ... ... ...
Graduated in 2°C Graduated in 5°F
J K
−6 to +400°C 25 11C 20 to 760°F 25 11F
L M
90 to 370°C 57 10C 200 to 700°F 57 10F
A
0.4°C to 225°C; 0.6°C above 225°C.
B
1°C to − 33°C; 2°C below − 33°C.
C
2°F to − 28°F; 4°F below − 28°F.
D
1°C to 301°C; 1.5°C above 301°C.
E
2°F to 574°F; 3°F above 574°F.
F
0.5°C to 150°C; 1°C above 150°C.
G
1°F to 300°F; 2°F above 300°F.
H
1°C to 300°C; 1.5°C above 300°C.
I
2°F to 570°F; 3°F above 570°F.
J
2°C to 260°C; 4°C above 260°C.
K
5°F to 500°F; 7°F above 500°F.
L
1°C to 260°C; 2°C above 260°C.
M
2.5°F to 500°F; 3.5°F above 500°F.
TABLE 4 Verification and Calibration TemperaturesA
Av Temp. Av Temp. Av Temp. Av Temp.

of Emergent of Emergent of Emergent of Emergent
Temperature Temperature Temperature Temperature
Mercury Mercury Mercury Mercury
Column Column Column Column
Thermometer 1C Thermometer 1F Thermometer 2C Thermometer 2F
−20 to +150°C 0 to 302°F −5 to +300°C −20 to +580°F
−20°C 15°C 0°F 60°F 0°C 22°C 32°F 72°F
0°C 22°C 32°F 72°F 75°C 34°C 150°F 90°F
50°C 30°C 122°F 86°F 150°C 35°C 300°F 95°F
100°C 33°C 212°F 91°F 225°C 40°C 450°F 105°F
150°C 36°C 302°F 97°F 300°C 45°C 580°F 114°F
−5 to +400°C 20 to 760°F −38 to +50°C −36 to +120°F
0°C 21°C 32°F 70°F −35°C 21°C −30°F 70°F
100°C 33°C 200°F 90°F 0°C 21°C 32°F 70°F
200°C 39°C 370°F 101°F 50°C 21°C 120°F 70°F
300°C 44°C 540°F 110°F
370°C 54°C 700°F 129°F
−80 to +20°C −112 to +70°F −2 to +300°C 30 to 580°F
−70°C 21°C −94°F 70°F 0°C 32°F
−35°C 21°C −30°F 70°F 50°C 100°F
0°CB 21°C 32°FB 70°F 100°C 200°F
20°C 21°C 70°F 70°F 150°C 300°F
200°C 400°F
250°C 500°F
300°C 570°F
−2 to +400°C 30 to 760°F −5 to +110°C 20 to 230°F
0°C 32°F 0°C 19°C 32°F 66°F
100°C 200°F 35°C 28°C 100°F 86°F
200°C 370°F 70°C 40°C 160°F 106°F
300°C 540°F 105°C 50°C 220°F 123°F
370°C 700°F
90 to 370°C 200 to 700°F −6 to +400°C 20 to 760°F
100°C 61°C 212°F 141°F 0°C 18°C 32°F 64°F
200°C 71°C 390°F 159°F 100°C 44°C 200°F 110°F
300°C 87°C 570°F 189°F 200°C 64°C 370°F 144°F
52
E 1 – 05
TABLE 4 Continued
370°C 104°C 700°F 220°F 300°C 91°C 540°F 187°F
370°C 115°C 700°F 240°F
Thermometer 12C Thermometer 12F Thermometer 13C Thermometer 14C
−20 to +102°C −5 to +215°F 155 to 170°C 38 to 82°C
−20°C −5°F 155°C 40°C 25°C
−10°C 15°F 163°C 50°C 25°C
0°C 32°F 170°C 60°C 25°C
10°C 60°F 70°C 25°C
20°C 85°F 80°C 25°C
30°C 110°F
40°C 135°F
50°C 160°F
60°C 185°F
70°C 210°F
80°C
90°C
100°C
Thermometer 14F Thermometer 15C Thermometer 15F Thermometer 16C
100 to 180°F −2 to +80°C 30 to 180°F 30 to 200°C
100°F 77°F 0°C 32°F 30°C
120°F 77°F 20°C 70°F 60°C
140°F 77°F 40°C 100°F 90°C
160°F 77°F 60°C 140°F 120°C
180°F 77°F 80°C 180°F 150°C
180°C
200°C
85 to 392°F 19 to 27°C 66 to 80°F 34 to 42°C
90°F 21°C 70°F 38°C
140°F 25°C 77°F 41°C
190°F
240°F
290°F
340°F
390°F
94 to 108°F 49 to 57°C 120 to 134°F 57 to 65°C
100°F 50°C 122°F 60°C
107°F 54°C 130°F 64°C
134 to 148°F 79 to 87°C 174 to 188°F 95 to 103°C
140°F 82°C 180°F 99°C
147°F 86°C 187°F 102°C
Thermometer 22F Thermometer 23C Thermometer 24C Thermometer 25C
204 to 218°F 18 to 28°C 39 to 54°C 95 to 105°C
210°F 20°C 22°C 40°C 35°C 95°C 75°C
212°F 25°C 25°C 50°C 42°C 100°C 64°C
Thermometer 26C Thermometer 27C Thermometer 28C Thermometer 28F
130 to 140°C 147 to 182°C 36.6 to 39.4°C 97.5 to 102.5°F
130°C 155°C 25°C 0°C 32°F
135°C 165°C 25°C 37.8°C 100°F
140°C 175°C 25°C 39°C 102°F
Thermometer 29C Thermometer 29F Thermometer 30F Thermometer 33C
52.6 to 55.4°C 127.5 to 132.5°F 207.5 to 212.5°F −38 to +42°C
0°C 32°F 32°F −35°C 5°C
54.4°C 130°F 210°F −20°C 15°C
55°C 132°F 212°F 0°C 20°C
20°C 25°C
40°C 30°C
−36.5 to +107.5°F 25 to 105°C 77 to 221°F 90 to 170°C
−31°F 41°F 25°C 25°C 77°F 77°F 100°C 70°C
53
E 1 – 05
TABLE 4 Continued
−4°F 59°F 45°C 37°C 113°F 99°F 120°C 63°C
32°F 68°F 65°C 43°C 149°F 109°F 140°C 57°C
68°F 77°F 85°C 45°C 185°F 113°F 160°C 50°C
104°F 86°F 100°C 45°C 212°F 113°F 170°C 47°C
194 to 338°F −2 to +68°C −2 to +52°C 24 to 78°C
212°F 158°F 0°C 25°C 0°C 25°C 25°C 25°C
250°F 145°F 15°C 25°C 15°C 25°C 40°C 25°C
285°F 134°F 30°C 25°C 30°C 25°C 55°C 25°C
320°F 122°F 45°C 25°C 50°C 25°C 75°C 25°C
338°F 116°F 65°C 25°C
Thermometer 39C Thermometer 40C Thermometer 41C Thermometer 42C
48 to 102°C 72 to 126°C 98 to 152°C 95 to 255°C
50°C 30°C 75°C 30°C 100°C 30°C 100°C 30°C
65°C 30°C 90°C 30°C 115°C 33°C 150°C 35°C
80°C 30°C 105°C 30°C 130°C 35°C 200°C 40°C
100°C 30°C 125°C 30°C 150°C 35°C 250°C 45°C
−51.6 to −34°C −61 to −29°F 18.6 to 21.4°C 66.5 to 71.5°F
−50°C −60°F 0°C 32°F
−45°C −50°F 20°C 68°F
−40°C −40°F 21°C 70°F
−35°C −30°F
0°C + 32°F
23.6 to 26.4°C 74.5 to 79.5°F 48.6 to 51.4°C 119.5 to 124.5
0°C 32°F 0°C 32°F
25°C 77°F 50°C 122°F
26°C 79°F 51°C 124°F
58.6 to 61.4°C 137.5 to 142.5°F 80.6 to 83.4°C 177.5 to 182.5°F
0°C 32°F 0°C 32°F
60°C 140°F 82.2°C 180°F
61°C 142°F 83°C 182°F
Thermometer 49C Thermometer 50F Thermometer 51F Thermometer 52C
20 to 70°C 54 to 101°F 69 to 116°F −10 to +5°C
20°C 25°C every 5° from 55°F every 5° from 70°F −10°C
35°C 25°C 0°C
50°C 25°C 5°C
70°C 25°C
20 to 100°C 68 to 213°F 19 to 35°C 66 to 95°F
20°C 70°F every 2° from 19°C every 4° from 66°F and including
50°C 120°F 95°F
75°C 170°F
100°C 210°F
−20 to +50°C −4 to +122°F −34 to +49°C −30 to +120°F
−20°C 25°C −3°F 77°F −30°C −20°F
0°C 25°C 32°F 77°F 0°C 32°F
25°C 25°C 77°F 77°F 25°C 80°F
50°C 25°C 122°F 77°F 45°C 120°F
−18 to +82°C 0 to 180°F 77 to 260°C 170 to 500°F
0°C 32°F 100°C 212°F
25°C 80°F 175°C 350°F
55°C 130°F 255°C 490°F
80°C 180°F
32 to 127°C 90 to 260°F −38 to +2°C −36 to +35°F
40°C 25°C 100°F 77°F −37°C −35°F
54
E 1 – 05
TABLE 4 Continued
60°C 25°C 150°F 77°F −30°C −15°F
80°C 25°C 200°F 77°F −20°C 0°F
100°C 25°C 250°F 77°F −10°C 15°F
120°C 25°C 0°C 32°F
−8 to +32°C 18 to 89°F 25 to 55°C 77 to 131°F
−7°C 20°F 0°C 32°F
0°C 32°F 25°C 80°F
10°C 50°F 35°C 95°F
20°C 70°F 45°C 115°F
30°C 88°F 55°C 130°F
50 to 80°C 122 to 176°F 75 to 105°C 167 to 221°F
0°C 32°F 0°C 32°F
50°C 125°F 75°C 168°F
60°C 145°F 85°C 185°F
70°C 160°F 95°C 200°F
80°C 175°F 105°C 220°F
95 to 155°C 203 to 311°F 145 to 205°C 293 to 401°F
0°C 32°F 0°C 32°F
100°C 205°F 150°C 300°F
110°C 240°F 170°C 340°F
130°C 275°F 190°C 370°F
150°C 310°F 205°C 400°F
195 to 305°C 383 to 581°F 295 to 405°C 563 to 761°F
0°C 32°F 0°C 32°F
200°C 400°F 300°C 570°F
235°C 460°F 335°C 640°F
270°C 520°F 370°C 700°F
305°C 580°F 400°C 760°F
−37 to +21°C −35 to +70°F −19.4 to −16.6°C −2.5 to +2.5°F
−35°C 21°C −30°F 70°F −19°C −2°F
−18°C 21°C 0°F 70°F −17.8°C 0°F
0°C 21°C 32°F 70°F 0°C 32°F
20°C 21°C 70°F 70°F
−41.4 to −38.6°C −42.5 to −37.5°F −55.4 to −52.6°C −67.5 to −62.5°F
−41°C −42°F −55°C −67°F
−40°C −40°F −53.9°C −65°F
0°C 32°F 0°C 32°F
Thermometer 75F Thermometer 76F Thermometer 77F Thermometer 78F
−35 to +35°F −65 to +5°F 245 to 265°F 295 to 315°F
−35°F 55°F −65°F 25°F 250°F 300°F
0°F 65°F −30°F 55°F 260°F 310°F
32°F 75°F + 5°F 75°F
Thermometer 79F Thermometer 80F Thermometer 81F Thermometer 82C
345 to 365°F 395 to 415°F 445 to 465°F −15 to +105°C
350°F 400°F 450°F 0°C 71°C
360°F 410°F 460°F 50°C 71°C
100°C 71°C
0 to 220°F 15 to 70°C 60 to 160°F 25 to 80°C
32°F 160°F 25°C 35°C 85°F 95°F 30°C 27°C
100°F 160°F 70°C 35°C 135°F 95°F 80°C 27°C
200°F 160°F
75 to 175°F 40 to 150°C 100 to 300°F 95 to 175°C
55
E 1 – 05
TABLE 4 Continued
100°F 80°F 50°C 54°C 150°F 130°F 100°C 99°C
150°F 80°F 150°C 54°C 250°F 130°F 175°C 99°C
200 to 350°F 150 to 205°C 300 to 400°F 10 to 200°C
225°F 210°F 160°C 132°C 300°F 270°F 40°C 48°C
325°F 210°F 200°C 132°C 400°F 270°F 100°C 56°C
150°C 62°C
200°C 68°C
50 to 392°F −20 to +10°C 0 to 30°C 20 to 50°C
110°F 119°F −20°C 15°C 0°C 20°C 20°C 25°C
212°F 132°F −10°C 15°C 10°C 20°C 30°C 25°C
300°F 143°F 0°C 15°C 20°C 20°C 40°C 25°C
392°F 154°F 10°C 15°C 30°C 20°C 50°C 25°C
40 to 70°C 60 to 90°C 80 to 110°C 100 to 130°C
40°C 25°C 60°C 30°C 80°C 30°C 100°C 35°C
50°C 25°C 70°C 30°C 90°C 30°C 110°C 35°C
60°C 25°C 80°C 30°C 100°C 30°C 120°C 35°C
70°C 25°C 90°C 30°C 110°C 30°C 130°C 35°C
Thermometer 96C Thermometer 97C Thermometer 97F Thermometer 98C
120 to 150°C −18 to +49°C 0 to 120°F 16 to 82°C
120°C 35°C −15°C 0°F 20°C
130°C 35°C 0°C 32°F 40°C
140°C 35°C 20°C 70°F 60°C
150°C 35°C 45°C 110°F 80°C
60 to 180°F −50 to +5°C −58 to +41°F 145 to 205°C
60°F −46°C −23°C −50°F −10°F 145°C 40°C
100°F −32°C −23°C −25°F −10°F 165°C 40°C
140°F −18°C −23°C 0°F −10°F 185°C 40°C
180°F 0°C −23°C 32°F −10°F 205°C 40°C
195 to 305°C 123 to 177°C 148 to 202°C 173 to 227°C
200°C 40°C 125°C 35°C 150°C 35°C 175°C 34°C
250°C 40°C 140°C 35°C 165°C 35°C 190°C 38°C
300°C 40°C 155°C 35°C 180°C 35°C 205°C 40°C
175°C 35°C 200°C 35°C 225°C 40°C
198 to 252°C 223 to 277°C 248 to 302°C 270 to 290°F
200°C 40°C 225°C 40°C 250°C 45°C 275°F
215°C 40°C 240°C 40°C 265°C 45°C 285°F
230°C 40°C 255°C 41°C 280°C 45°C
250°C 40°C 275°C 46°C 300°C 45°C
320 to 340°F 133.6 to 136.4°C 272.5 to 277.5°F 170 to 250°C
325°F 0°C 32°F 170°C 35°C
335°F 135°C 275°F 200°C 40°C
136°C 277°F 250°C 45°C
Thermometer 112C Thermometer 113C Thermometer 113F Thermometer 114C
4 to 6°C −1 to +175°C 30 to 350°F −80 to +20°C
0°C 0°C 32°F −75°C
4°C 50°C 122°F −60°C
5°C 100°C 212°F −40°C
6°C 150°C 302°F 0°C
175°C 347°F
18.9 to 25.1°C 23.9 to 30.1°C 28.6 to 31.4°C 83.5 to 88.5°F
every 1°C every 1°C 0°C 32°F
from 19.0°C from 24.0°C 30°C 86°F
31°C 88°F
56
E 1 – 05
TABLE 4 Continued
−38.3 to −30°C −37 to −22°F 38.6 to 41.4°C 98.6 to 101.4°C
−38°C 18°C −36°F 64°F 0°C 0°C
−30°C 20°C −22°F 68°F 40°C 100°C
0°C 0°C + 32°F 32°F 41°C 101°C
−45 to −35°C −35 to −25°C −25 to −15°C −15 to −5°C
−45°C −35°C −25°C −15°C
−40°C −30°C −20°C −10°C
−35°C −25°C −15°C −5°C
−27.4 to −24.6°C −17.5 to −12.5°F −21.4 to −18.6°C −1.4 to +1.4°C
−27°C −17°F −21°C 0°C
−26.1°C −15°F −20°C 1°C
0°C 32°F 0°C
29.5 to 34.5°F 91.6 to 94.4°C 197.5 to 202.5°F −7 to +105°C
32°F 0°C 32°F 0°C
34°F 93.3°C 200°F 35°C
94°C 202°F 70°C
105°C
20 to 220°F 148.6 to 151.4°C –38 to +2°C 144 to 156°C
32°F 0°C –36 25°C 145°C 40°C
100°F 150°C –30 25°C 150°C 40°C
160°F 151°C –24 25°C 155°C 40°C
220°F –18 25°C
–12 25°C
–6 25°C
0 25°C
38 to 93°C 100 to 200°F –20 to +60°C –5 to +140°F
50°C 35°C 125°F 95°F –20°C –5°F
90°C 35°C 195°F 95°F –10°C 15°F
0°C 32°F
10°C 60°F
20°C 85°F
30°C 110°F
40°C 135°F
50°C
60°C
Thermometer 137C
80 to 100°C
80°C 30°C
90°C 30°C
100°C 30°C
A
For verification and calibration of total immersion thermometers see Test Method E 77.
For Thermometers 1C, 1F, 2C, 2F, 3C, 3F, 23C, 24C, and 25C the emergent column temperatures correspond on the average with those attained in verification using
equipment such as that described in Test Method E 77.
For all other thermometers listed, the emergent column temperatures are those attained when using the thermometers in the test equipment for which the thermometers
were originally designed. In some cases these temperatures are markedly different from those realized during verification. Also in some instances, such as Thermometers
35C and 35F, the values may not seem reasonable. Analysis of the factors affecting emergent column temperatures in use will provide the explanation for such apparent
inconsistencies.
B
This thermometer is especially sensitive to changes in emergent column temperatures because organic liquids are used as the thermometer fluid. As a means of
avoiding errors due to this cause the ice point should be taken at total immersion and the correction calculated for partial immersion by using the emergent stem correction
formula given in Test Method E 77.
57
E 1 – 05
Part B—Enclosed-Scale Thermometer 20.1.4 The meniscus shall be distorted as little as possible
by striae or impurities in the glass.
16. Specifications
21. Vacuum
16.1 The thermometers shall conform to the detailed speci-
fications given in Table 5 and the requirements given in 21.1 The capillary above the mercury shall be evacuated,
Sections 17-24. and the vacuum shall be such that no difficulty is experienced
in rejoining the column after setting.
TABLE 5 Specifications for Enclosed Scale Thermometers
22. Construction
ASTM Number 115C–86
Range (nominal), °C 5 or 6 22.1 Shape—The thermometer shall be straight and have
Graduation interval, °C 0.01 insofar as practical circular cross sections.
Adjustable range, °C –10 to 120
Total length, max, mm 640
22.2 Top Finish—The top of the thermometer shall be
Length of main scale/° (graduated length), mm 44 6 4 closed by a suitable cap.
Distance from bottom of bulb to lowest 22.3 Scale—The graduated scale shall be of opal glass and
numbered graduation line, mm 200 to 240
Diameter of sheath (top portion) max, mm 16
shall be securely fastened to prevent relative displacement
External bulb diameter, max, mm 11 between the capillary and scale, and in such a way that it can
Bulb length, mm 30 to 50 freely expand in length.
Bulb shoulder length, max, mm 11
Bulk—dimension/bore ratio, max be/d = 15
22.4 Capillary Tube—The capillary tube shall be transpar-
(see 9.2.3) ent, its inside shall be smooth, and its cross-sectional area in
the scale portion shall not show variations from the average
17. Type greater than 5 %. The bore shall be large enough in relation to
17.1 The thermometers shall be of the enclosed-scale the dimensions of the thermometer bulb to ensure that (without
mercury-in-glass type with adjustable range. tapping), the jumping of the meniscus does not exceed one half
of the smallest scale division when the temperature is rising at
18. Temperature Scale a uniform rate not exceeding 0.05°C/min.
18.1 Temperature differences indicated by the thermometers NOTE 5—According to Hall and Leaver, this condition can be achieved
shall be in terms of the International Temperature Scale of or bettered by keeping the ratio be/d < 15.6 The external pressure
1990 (ITS-90)4 as adopted by the General Conference on coefficient is defined by the expression
Weights and Measures. be 5 0.52 De 2/~D e 2– Di 2! (1)
19. Immersion where:

19.1 To obtain the full precision of the thermometer for d = bore of the capillary, mm,
be = external pressure coefficient, m·deg C/cm,
difference measurements, the ambient (stem) temperature and
De = external diameter of the thermometer bulb, and
immersion depth must be the same in all measurements. Di = internal diameter of the thermometer bulb.
19.2 The thermometers are for use in a vertical position. 22.5 Adjusting Device—For adjusting the amount of mer-
19.3 In order to measure Celsius- or kelvin-scale tempera- cury in the bulb and main capillary to the intended range, an
tures after the setting temperature has been determined at a enlargement shall be provided above the measuring capillary to
given immersion depth by comparison with a standard, the serve as a reservoir for the separated mercury. Adjustment shall
thermometer must be used at the same immersion for all main be possible without difficulty. To facilitate adjustment of the
scale readings obtained at this setting. range an auxiliary scale may be provided. Two designs of
adjusting devices are indicated in Fig. 12. Operation of the
20. Glass
adjusting device shall require a temperature of approximately,
20.1 The bulb and sheath of the thermometer should pref- but not less than, 35°C above the setting point.
erably be made of the same type of thermometric glass. This 22.6 Dimensions—The dimensions shall be as given in
glass shall be selected so that the finished thermometer meets Table 5 and Fig. 12.
the following requirements: 22.7 Graduation and Figuring:
20.1.1 The bulb glass shall be stabilized by suitable heat 22.7.1 The range of graduation of the thermometer shall be
treatment to ensure that the accuracy requirements of Section as specified in Table 5.
23 can be met, 22.7.2 The graduation lines shall be clearly defined and of
20.1.2 Strain in the glass shall be reduced to a level uniform thickness which should in no case exceed 0.05 mm.
sufficient to minimize the possibility of fracture due to thermal The lines shall be at right angles to the axis of the thermometer.
or mechanical shock, 22.7.3 The thermometer shall be graduated and figured for
20.1.3 The accuracy of the reading shall not be impaired by use in a vertical position. The arrangement of the graduation
devitrifying during manufacture, and lines shall be as specified in Fig. 13. Each 0.1-deg line shall be
a long line; each 0.05-deg line shall have a length of two thirds
of the long line; and each 0.01-deg line shall have a length of
4
“The International Temperature Scale of 1990,” Amended Edition of 1990, one third of the long line. All graduation lines shall be readily
Metrologia, Vol 27, No. 1, 1990, pp. 3–15. visible from both sides of the capillary.
58
E 1 – 05
22.7.4 The scale shall be extended beyond the lowest long 23.2 The stability of the thermometer shall be such that the
graduation line by from two to five scale divisions. zero reading does not change by more than 0.01°C in 24 h
22.7.5 Figuring shall be as shown in Fig. 13. The lowest when left at the setting temperature after the bulb of the
long graduation line in upward reading thermometers, and the thermometer has been heated for at least 15 min to a tempera-
highest long graduation line in downward reading thermom- ture 35°C above the setting point.
eters shall be figured “0.” Each full degree shall be figured with
24. Inscriptions
large numbers. Every second intermediate one tenth of a degree
shall be figured with small numbers on the right-hand side of 24.1 The following inscriptions shall be permanently and
the scale. legibly marked on the thermometer:
24.1.1 Temperature scale (abbreviations such as “°C” or
23. Interval Error “C”),
24.1.2 Bulb glass type (the glass may be identified by a
23.1 The interval error of each partial interval of a range of colored stripe or stripes or by an inscription on the thermom-
0.5°C shall not exceed 60.01°C. The maximum error for any eter),
larger interval shall not exceed 0.02°C. These values refer to 24.1.3 Identification number (manufacturer’s serial num-
the adjustment of the thermometer to “0” at 20°C and at a ber),
temperature of the emergent stem of 20°C. 24.1.4 Manufacturer’s tradename or mark, and
NOTE 6—The first part of this requirement essentially requires that 24.1.5 ASTM 115C.
calibration be performed at 0.5°C intervals. The need for this is indicated
25. Keywords
by findings at the National Institute of Standards and Technology that
calibration every 40 to 50 divisions is required for reliable interpolation to 25.1 bulb; liquid-in-glass thermometers; standard specifica-
one or two tenths of a division. tion; stem; temperature; thermometer
FIG. 1 Test Gage for Checking Enlargements on Thermometers

9C, 9F, 10C, 10F, 57C, 57F, 88C, and 88F
59
E 1 – 05
FIG. 2 Bulb of ASTM Congealing Point Thermometers 54C and

54F
FIG. 3
FIG. 4
FIG. 5
60
E 1 – 05
FIG. 6
FIG. 7
FIG. 8
FIG. 9
61
E 1 – 05
FIG. 10
FIG. 11
62
E 1 – 05
NOTE 1—All dimensions are in millimetres.

FIG. 12 Enclosed Scale Adjustable Range Thermometers
FIG. 13 Graduation and Figuring
63
E 1 – 05
FIG. 14 Schemes for Graduation and Figuring
ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned
in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk
of infringement of such rights, are entirely their own responsibility.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and
if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the
responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should
make your views known to the ASTM Committee on Standards, at the address shown below.
This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,
United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above
address or at 610-832-9585 (phone), 610-832-9555 (fax), or [email protected] (e-mail); or through the ASTM website
(www.astm.org).
64

ASTM Liquid-in-Glass Thermometers: Standard Specification For

Uploaded by

Copyright:

Available Formats

ASTM Liquid-in-Glass Thermometers: Standard Specification For

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ASTM Liquid-in-Glass Thermometers: Standard Specification For

Uploaded by

Copyright:

Available Formats

Method 9501—Federal Test

Designation: E 1 – 05 Method Standard No. 791b

Standard Specification for

1. Scope responsibility of the user of this standard to establish appro-

Long, narrow shape; mercury shall be in the chamber at 0 °C (32 °F).

ASTM No. 1C-99 1F-99FF 2C-99 2F-99FF 3C-99 3F-99FF

ASTM No. 5C-86 5F-86FF 6C-86 6F-86FF 7C-86 7F-86FF

C Stem OD, mm 6.0 to 8.0 6.0 to 8.0 6.0 to 8.0

Bottom of bulb to line at 0°C 32°F −20°C −4°F 155°C

C Stem OD, mm 6.0 to 8.0 6.0 to 8.0 6.0 to 8.0

E Bulb OD, mm ≤5.0 and ≥stem ≥stem ≤5.0 and ≥stem

E Bulb OD, mm 5.5 to 6.5 5.5 to 6.5 5.5 to 6.5

C Stem OD, mm 6.0 to 8.0 6.0 to 8.0 6.0 to 8.0

C Stem OD, mm 6.0 to 8.0 6.0 to 8.0 6.0 to 8.0

E Bulb OD, mm 5.5 to ≥stem

E Bulb OD, mm ≥stem ≥stem ≥stem

C Stem OD, mm 7.0 to 8.0 7.0 to 8.0 7.0 to 8.0

C Stem OD, mm 7.0 to 8.0 7.0 to 8.0 7.0 to 8.0

E Bulb OD, mm 6.0 to 7.0 6.0 to 7.0 6.0 to 7.0

E Bulb OD, mm ≥stem ≥stem ≥stem

H Bottom of bulb to ice-point, mm

C Stem OD, mm 6.0 to 7.0 6.0 to 7.0 6.0 to 7.0

B Total length, mm 365 to 375 365 to 375 365 to 375

B Total length, mm 365 to 375 365 to 375 365 to 375

C Stem OD, mm 6.0 to 8.0 6.0 to 8.0 6.0 to 8.0

C Stem OD, mm 6.0 to 8.0 6.0 to 8.0 6.0 to 8.0

E Bulb OD, mm ≤5.0 and ≥stem ≤5.0 and ≥stem ≥stem

C Stem OD, mm 6.0 to 7.0 6.0 to 7.5 6.0 to 8.0

Special inscription ASTM ASTM ASTM

C Stem OD, mm 6.0 to 8.0 6.0 to 7.0 6.0 to 8.0

E Bulb OD, mm ≥stem ≥stem ≥stem ≥stem

TABLE 2 Alphabetical List of ASTM Thermometers Covered by Specification E 1

NOTE 1—The specifications appear in numeric sequence in this standard.

Thermometer No. Thermometer No.

TABLE 3 List of ASTM Thermometers by Temperature Range

Scale ASTM Scale ASTM

TABLE 4 Verification and Calibration TemperaturesA

Av Temp. Av Temp. Av Temp. Av Temp.

19. Immersion where:

FIG. 1 Test Gage for Checking Enlargements on Thermometers

FIG. 2 Bulb of ASTM Congealing Point Thermometers 54C and

NOTE 1—All dimensions are in millimetres.

FIG. 13 Graduation and Figuring

FIG. 14 Schemes for Graduation and Figuring

You might also like