Scribd
Upload
2K views

DSC NEO Programming

This document provides instructions for configuring a DSC NEO Power Series alarm panel to communicate with a central monitoring station using Contact ID reporting format. It describes how to program the panel's phone number, account code, and enable reporting for alarm, tamper, and open/close events. It also provides steps to program a momentary keyswitch zone and an output to indicate armed/disarmed status. Programming is done through the panel's keypad interface by navigating menus and entering option codes.

Uploaded by

Jaime Hernandez Hernandez
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
2K views

DSC NEO Programming

This document provides instructions for configuring a DSC NEO Power Series alarm panel to communicate with a central monitoring station using Contact ID reporting format. It describes how to program the panel's phone number, account code, and enable reporting for alarm, tamper, and open/close events. It also provides steps to program a momentary keyswitch zone and an output to indicate armed/disarmed status. Programming is done through the panel's keypad interface by navigating menus and entering option codes.

Uploaded by

Jaime Hernandez Hernandez
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

DSC NEO Power Series Configuration Manual

(HS2016/2032/2064/2128)

*NOTE: M2M advises that an experienced alarm installer program these panels as further programming is
required to ensure proper performance.
Full panel testing & signal confirmation must be completed by the installer.

*IN1 and OUT1 – optional terminals for the remote arm/disarm feature

Wiring the MN01-4G to the Alarm Panel


Enable Contact ID reporting:
Keypad Display Keypad entry Action description
Select: *85555 To enter Programming mode
Select: 301 To enter menu” First phone number”
Select: 001 001 To select first phone number
DFFFFF (or 123456*6*# Enter actual or non-existing number (any number will do, 123456 is example,
previous number) press *6* to enter/exit hex mode in order to fill the rest with ‘F’s)
Select: 383 Enter Communication Options 4
Comm. Option 4: 2# Toggle 2 to OFF, to set the programmable account code in 310 to 4 digits, # saves
Select: 310 To enter menu “System account code”
System account: 000 To enter submenu for the whole system (001, 002… for more partitions)
System account: 1234# Enter 4-digit account number for CMS identification (1234# is an example)
Select: 311 To enter menu “Reporting”
Select: 001 To go to “Alarm restore options’
Toggle receiver#1 *# Press * to select “Y” (yes) – “Alarm/Restore” events are reported to telephone
number 1
Tamper restore: 002 To go to “Tamper/Tamper restore”
Toggle receiver#1 *# Press * to select “Y” (yes) – “Tamper/Tamper restore” events are reported to
telephone number 1
Opening/Closing 003 To go to “Open/Close” events
*## Press * to select “Y” (yes) – “Open/Close” events are reported to telephone
number 1, # to save, # to exit to main menu
Select: 350 To enter “Communicator Alarm Format” options
Enter Data: 001 To select phone number 1
Enter Data: 03# 03 is for Contact ID, # to save (alternatively you can use <> to move in the menu)
Select: 380 Enter First Communication Options
Comms. 1## Toggle 1 to ON, 3 and 4 must be off (DTMF touch-tone dialing, DTMF dialing for
Enabled: all attempts), # to save

Program Keyswitch zone and output:


Keypad Display Keypad Action description
entry
Select: *85555 To enter Programming mode
Select: 001 Enter zone definition menu
Zone definitions * Enter Zone 1 definition
Zone 1 066 To choose Momentary Keyswitch for Zone 1
Momentary KSW ## To exit to main menu
Select: 013 Enter First System Options (to configure Normally Closed Zones)
Toggle 1 * Press the * or toggle buttons <> until 1 is ON (all zones are wired as normally closed
circuits with returns to COM terminal)
Toggle Option 1 ## Press ## to exit to main menu
Select: 009 Enter I/O Programming menu
PGM 1 001 To enter PGM 1 subsection
PGM 1 115 To program the output to report Armed/Disarmed status
PGM 1 ## Press ## to exit to main menu

You might also like