2014 Juke
2014 Juke
2014 Juke
2014 JUKE
OWNER’S MANUAL
In case of emergency 6
Index 10
0 Illustrated table of contents
JVC0533X
SSI0766
JVC0534X
JVC0413X
JVC0184X
JVC0572X
1. Outside mirror remote control switch (P.3-25) — Electric power steering system (P.5-38)
2. Headlight, fog light and turn signal switch — Horn (P.2-39)
— Headlight (P.2-35) — Driver’s supplemental air bag (P.1-38)
— Turn signal light (P.2-38) 5. Wiper and washer switch (P.2-32)
— Fog light* (P.2-39) 6. Shift lever
3. Paddle shifter* (P.5-20) — Continuously Variable Transmission (CVT)
4. Steering wheel (P.5-17)
JVC0607X
1. Meters and gauges (P.2-5) — Heater and air conditioner control (P.4-20)
2. Center ventilator (P.4-19) — Defroster switch (P.2-35)
3. Audio system* or Navigation system** (P.4-28) 5. Heater and air conditioner control (models
— Clock* (P.2-41) without Integrated Control System) (P.4-20)
4. Hazard warning flasher switch (P.6-2) — Defroster switch (P.2-35)
5. Integrated Control System* (P.2-21) 6. Front passenger supplemental air bag (P.1-38)
— Drive mode (P.5-25) 7. Side ventilator (P.4-19)
SIC4601
SDI2639
CAUTION
SSS0133
When adjusting the seat positions, be
sure not to contact any moving parts to
avoid possible injuries and/or damage.
well back in the seat with both feet
WARNING on the floor and adjust the seat
properly. See “Precautions on seat
. Do not ride in a moving vehicle belt usage” (P.1-10).
when the seatback is reclined. This
. After adjustment, gently rock in the
can be dangerous. The shoulder belt
seat to make sure it is securely
will not be against your body. In an
locked.
accident, you could be thrown into it
and receive neck or other serious . Do not leave children unattended
injuries. You could also slide under inside the vehicle. They could un-
the lap belt and receive serious knowingly activate switches or con-
internal injuries. trols. Unattended children could
become involved in serious acci-
. For the most effective protection
dents.
when the vehicle is in motion, the
seat should be upright. Always sit
1-2 Safety — Seats, seat belts and supplemental restraint system
FRONT SEATS
Front manual seat adjustment
Forward and backward:
Pull the lever *
1 up and hold it while you slide
the seat forward or backward to the desired
position. Release the lever to lock the seat in
position.
Reclining (Type A):
To recline the seatback, pull the lever *
2 up and
lean back. To bring the seatback forward, pull
the lever up and lean your body forward. Release
SSS0792 the lever to lock the seatback in position.
Type A The reclining feature allows adjustment of the
seatback for occupants of different sizes for
added comfort and to help obtain proper seat
belt fit. (See “Precautions on seat belt usage”
(P.1-10).) Also, the seatback can be reclined to
allow occupants to rest when the vehicle is
stopped and the transmission is in the P (Park)
position or N (Neutral) position with the parking
brake fully applied.
Reclining (Type B):
To recline the seatback, turn the adjusting dial
*2 toward the rear of the vehicle and lean back.
To bring the seatback forward, turn the adjusting
JVR0342X dial toward the front of the vehicle and lean your
Type B body forward. Release the dial to lock the
injury.
CAUTION . When returning the seatbacks to the WARNING
upright position, be certain they are
When folding or returning the Head restraint/headrest supplement
completely secured in the latched
seatback(s) to the upright position, to the other vehicle safety systems. They
position. If they are not completely
avoid injury to yourself and others: may provide additional protection
secured, passengers may be injured
. Make sure that the seat path is clear in an accident or sudden stop. against injury in certain rear end colli-
before moving the seat. sions. Adjustable head restraints/head-
rests must be adjusted properly, as
specified in this section. Check the
adjustment after someone else uses
WARNING the seat. Do not attach anything to the
head restraint/headrest stalks or re-
. Do not fold down the rear seats move the head restraint/headrest. Do
when occupants are in the rear seat not use the seat if the head restraint/
area or any objects are on the rear headrest has been removed. If the head
seats. restraint/headrest was removed, rein-
. Never allow anyone to ride in the stall and properly adjust the head
cargo area or on the rear seats restraint/headrest before an occupant
when they are in the fold-down uses the seating position. Failure to
position. Use of these areas by follow these instructions can reduce the
passengers without proper re- effectiveness of the head restraint/
straints could result in serious injury headrest. This may increase the risk of
in an accident or sudden stop. serious injury or death in a collision.
. Properly secure all cargo with ropes
or straps to help prevent it from
sliding or shifting. Do not place
cargo higher than the seatbacks. In
a sudden stop or collision, unse-
cured cargo could cause personal
Safety — Seats, seat belts and supplemental restraint system 1-5
. The non-adjustable head restraints/head-
rests have single locking notch to secure
them to the seat frame.
. Proper Adjustment:
— For the adjustable type, align the head
restraint/headrest so the center of your
ear is approximately level with the center
of the head restraint/headrest.
— If your ear position is still higher than the
recommended alignment, place the head
restraint/headrest at the highest position.
. If the head restraint/headrest has been
JVR0051X
removed, ensure that it is reinstalled and SSS0992
locked in place before riding in that desig-
The illustration shows the seating positions nated seating position. ADJUSTABLE HEAD RESTRAINT/
equipped with head restraint/headrest. HEADREST COMPONENTS
Indicates the seating position is equipped 1. Removable head restraint/headrest
with a head restraint. 2. Multiple notches
Indicates the seating position is equipped 3. Lock knob
with a headrest.
4. Stalks
+ indicates the seating position is not equipped
with a head restraint or headrest.
. Your vehicle is equipped with a head
restraint/headrest that may be integrated,
adjustable or non-adjustable.
. Adjustable head restraints/headrests have
multiple notches along the stalk to lock them
in a desired adjustment position.
SSS1036 SSS0508
SSS0134
SSS0292 SSS0290
2. Slowly pull the seat belt out of the retractor 3. Position the lap belt portion low and snug
and insert the tongue into the buckle until on the hips as shown.
you hear and feel the latch engage. 4. Pull the shoulder belt portion toward the
. The retractor is designed to lock retractor to take up extra slack. Be sure the
during a sudden stop or on impact. shoulder belt is routed over your shoulder
A slow pulling motion permits the and across your chest.
belt to move and allows you some
The front passenger seat and the rear seating
freedom of movement in the seat.
positions three-point seat belts have two modes
. If the seat belt cannot be pulled from
of operation:
its fully retracted position, firmly pull
the belt and release it. Then . Emergency Locking Retractor (ELR)
smoothly pull the belt out of the . Automatic Locking Retractor (ALR)
retractor. The Emergency Locking Retractor (ELR) mode
allows the seat belt to extend and retract to
allow the driver and passengers some freedom
WARNING WARNING
. After adjustment, release the ad- . Only NISSAN seat belt extenders,
justment button and try to move the made by the same company which
shoulder belt anchor up and down made the original equipment seat
to make sure it is securely fixed in belts, should be used with NISSAN
position. seat belts.
. The shoulder belt anchor height . Adults and children who can use the
should be adjusted to the position standard seat belt should not use an
best for you. Failure to do so may extender. Such unnecessary use
reduce the effectiveness of the SSS1138 could result in serious personal
entire restraint system and increase injury in the event of an accident.
the chance or severity of injury in an Seat belt hooks . Never use seat belt extenders to
accident. When the rear seat belts are not in use and install child restraints. If the child
when folding down the rear seats, hook the rear restraint is not secured properly, the
seat belts on the seat belt hooks. child could be seriously injured in a
SEAT BELT EXTENDERS collision or a sudden stop.
If, because of body size or driving position, it is
not possible to properly fit the lap-shoulder belt
SEAT BELT MAINTENANCE
and fasten it, an extender that is compatible with . To clean the seat belt webbing, apply a
the installed seat belts is available that can be mild soap solution or any solution recom-
purchased. The extender adds approximately 8 mended for cleaning upholstery or carpets.
in (200 mm) of length and may be used for either Then wipe with a cloth and allow the seat
the driver or front passenger seating position. belts to dry in the shade. Do not allow the
See a NISSAN dealer for assistance with seat belts to retract until they are completely
purchasing an extender if an extender is dry.
— NISSAN recommends that all — Never use the anchor points for
child restraints be installed in adult seat belts or harnesses.
SSS0100
the rear seat. Studies show that — A child restraint with a top tether
children are safer when properly strap should not be used in the
restrained in the rear seat than front passenger seat.
1-18 Safety — Seats, seat belts and supplemental restraint system
— Keep seatbacks as upright as For details, see “Lower Anchors and Tethers for . If the combined weight of the child and child
possible after fitting the child CHildren System (LATCH)” (P.1-20). restraint is greater than 65 lbs (29.5 kg), use
restraint. If you do not have a LATCH compatible child the vehicle’s seat belt (not the lower
restraint, the vehicle seat belts can be used. anchors) to install the child restraint.
— Infants and children should al- . Be sure to follow the child restraint manu-
ways be placed in an appropri- Several manufacturers offer child restraints for
facturer’s instructions for installation.
ate child restraint while in the infants and small children of various sizes. When
selecting any child restraint, keep the following All U.S. states and Canadian provinces or
vehicle.
points in mind: territories require that infants and small
. When the child restraint is not in children be restrained in an approved child
use, keep it secured with the LATCH . Choose only a restraint with a label certifying
restraint at all times while the vehicle is
system or a seat belt. In a sudden that it complies with Federal Motor Vehicle
being operated. Canadian law requires the
stop or collision, loose objects can Safety Standard 213 or Canadian Motor
top tether strap on forward-facing child
injure occupants or damage the Vehicle Safety Standard 213.
restraints be secured to the designated
vehicle. . Check the child restraint in your vehicle to anchor point on the vehicle.
be sure it is compatible with the vehicle’s
seat and seat belt system.
. If the child restraint is compatible with your
CAUTION vehicle, place your child in the child restraint
and check the various adjustments to be
A child restraint in a closed vehicle can
sure the child restraint is compatible with
become very hot. Check the seating
your child. Choose a child restraint that is
surface and buckles before placing a
designed for your child’s height and weight.
child in the child restraint.
Always follow all recommended procedures.
. If the combined weight of the child and child
This vehicle is equipped with a universal child restraint is less than 65 lbs (29.5 kg), you
restraint anchor system, referred to as the may use either the LATCH anchors or the
LATCH (Lower Anchors and Tethers for CHil- seat belt to install the child restraint (not
dren) system. Some child restraints include rigid both at the same time).
or webbing-mounted attachments that can be
connected to these anchors.
LATCH lower anchor location Installing child restraint LATCH lower When installing a child restraint, carefully read
anchor attachments and follow the instructions in this manual and
The LATCH anchors are located at the rear of
those supplied with the child restraint.
the seat cushion near the seatback. A label is LATCH compatible child restraints include two
attached to the seatback to help you locate the rigid or webbing-mounted attachments that can Top tether anchor
LATCH anchors. be connected to two anchors located at certain
seating positions in your vehicle. With this
system, you do not have to use a vehicle seat WARNING
belt to secure the child restraint. Check your
child restraint for a label stating that it is . If the cargo cover (if so equipped)
compatible with LATCH. This information may contacts the top tether strap when it
also be in the instructions provided by the child is attached to the top tether anchor,
restraint manufacturer. remove the cargo cover from the
vehicle or secure it on the cargo
floor below its attachment location.
If the cargo cover is not removed, it
Safety — Seats, seat belts and supplemental restraint system 1-21
may damage the top tether strap in a collision.
during a collision. Your child could
be seriously injured or killed in a Anchor points are located on the back side of
collision if the child restraint top the seatbacks.
tether strap is damaged.
The child restraint top tether strap must be used
. Do not allow cargo to contact the when installing child restraints with the LATCH
top tether strap when it is attached lower anchor attachments or seat belts.
to the top tether anchor. Properly
If you have any questions when installing a
secure the cargo so it does not
top tether strap child restraint on the rear
contact the top tether strap. Cargo
seat, consult a NISSAN dealer for details.
that is not properly secured or cargo
that contacts the top tether strap REAR-FACING CHILD RESTRAINT IN-
may damage the top tether strap JVR0198X
STALLATION USING LATCH
during a collision. Your child could Refer to all Warnings and Cautions in the “Child
be seriously injured or killed in a Top tether anchor point locations safety” and “Child restraints” sections before
collision if the child restraint top installing a child restraint.
tether strap is damaged. NISSAN does not recommend the use of the
WARNING lower anchors if the combined weight of the
child and the child restraint exceeds 65 lbs
Child restraint anchorages are de-
(29.5 kg). If the combined weight of the child
signed to withstand only those loads
and the child restraint is greater than 65 lbs
imposed by correctly fitted child re-
(29.5 kg), use the vehicle’s seat belt (not the
straints. Under no circumstances are
lower anchors) to install the child restraint. Be
they to be used to attach adult seat
sure to follow the child restraint manufacturer’s
belts, or other items or equipment to
instructions for installation.
the vehicle. Doing so could damage the
child restraint anchorages. The child Follow these steps to install a rear-facing child
restraint will not be properly installed restraint using the LATCH system:
using the damaged anchorage, and a
child could be seriously injured or killed
1-22 Safety — Seats, seat belts and supplemental restraint system
1. Position the child restraint on the seat.
Always follow the child restraint manufac-
turer’s instructions.
SSS0648 SSS0649
Rear-facing web-mounted — step 2 Rear-facing rigid-mounted — step 2
2. Secure the child restraint anchor attach-
ments to the LATCH lower anchors. Check
to make sure the LATCH attachment is
properly attached to the lower anchors.
SSS0639 SSS0650
Rear-facing — step 3 Rear-facing — step 4
3. For child restraints that are equipped with 4. After attaching the child restraint, test it
webbing-mounted attachments, remove any before you place the child in it. Push it from
additional slack from the anchor attach- side to side while holding the child restraint
ments. Press downward and rearward firmly near the LATCH attachment path. The child
in the center of the child restraint with your restraint should not move more than 1 inch
hand to compress the vehicle seat cushion (25 mm), from side to side. Try to tug it
and seatback while tightening the webbing forward and check to see if the LATCH
of the anchor attachments. attachment holds the restraint in place. If the
restraint is not secure, tighten the LATCH
attachment as necessary, or put the restraint
in another seat and test it again. You may
need to try a different child restraint or try
installing by using the vehicle seat belt (if
applicable). Not all child restraints fit in all
types of vehicles.
1-24 Safety — Seats, seat belts and supplemental restraint system
ger air bag and status light” (P.1-46).
SSS0100 SSS0100
Rear-facing — step 1
REAR-FACING CHILD RESTRAINT IN-
Refer to all Warnings and Cautions in the “Child
STALLATION USING THE SEAT BELTS safety” (P.1-16) and “Child restraints” (P.1-18)
before installing a child restraint.
WARNING NISSAN does not recommend the use of the
lower anchors if the combined weight of the
The three-point seat belt with Auto- child and the child restraint exceeds 65 lbs
matic Locking Retractor (ALR) must be (29.5 kg). If the combined weight of the child
used when installing a child restraint. and the child restraint is greater than 65 lbs
Failure to use the ALR mode will result (29.5 kg), use the vehicle’s seat belt (not the
in the child restraint not being properly lower anchors) to install the child restraint. Be
secured. The restraint could tip over or sure to follow the child restraint manufacturer’s
be loose and cause injury to a child in a instructions for installation.
sudden stop or collision. Also, it can Follow these steps to install a rear-facing child
change the operation of the front restraint using the vehicle seat belts in the rear
passenger air bag. See “Front passen-
Safety — Seats, seat belts and supplemental restraint system 1-25
seats:
1. Child restraints for infants must be
used in the rear-facing direction and
therefore must not be used in the front
seat. Position the child restraint on the seat.
Always follow the restraint manufacturer’s
instructions.
SSS0654 SSS0655
Rear-facing — step 2 Rear-facing — step 3
2. Route the seat belt tongue through the child 3. Pull the shoulder belt until the belt is fully
restraint and insert it into the buckle until you extended. At this time, the seat belt retractor
hear and feel the latch engage. Be sure to is in the Automatic Locking Retractor (ALR)
follow the child restraint manufacturer’s mode (child restraint mode). It reverts to the
instructions for belt routing. Emergency Locking Retractor (ELR) mode
when the seat belt is fully retracted.
(29.5 kg). If the combined weight of the child 2. Secure the child restraint anchor attach- 3. The back of the child restraint should be
and the child restraint is greater than 65 lbs ments to the LATCH lower anchors. Check secured against the vehicle seatback.
(29.5 kg), use the vehicle’s seat belt (not the to make sure the LATCH attachment is If necessary, adjust or remove the head
lower anchors) to install the child restraint. Be properly attached to the lower anchors. restraint to obtain the correct child restraint
sure to follow the child restraint manufacturer’s If the child restraint is equipped with a top fit. If the head restraint is removed, store it in
instructions for installation. tether strap, route the top tether strap and a secure place. Be sure to reinstall the
Follow these steps to install a forward-facing secure the tether strap to the tether anchor head restraint when the child restraint
child restraint using the LATCH system: point. See “Installing top tether strap” (P.1- is removed. See “Head restraints/head-
1. Position the child restraint on the seat. 30). Do not install child restraints that rests” (P.1-5) for head restraint adjustment
Always follow the child restraint manufac- require the use of a top tether strap in information.
turer’s instructions. seating positions that do not have a top If the seating position does not have a head
tether anchor. restraint and it is interfering with the proper
child restraint fit, try another seating position
or a different child restraint.
SSS0647 SSS0638
Forward-facing — step 4 Forward-facing — step 6
4. For child restraints that are equipped with 6. After attaching the child restraint, test it
webbing-mounted attachments, remove any before you place the child in it. Push it from
additional slack from the anchor attach- side to side while holding the child restraint
ments. Press downward and rearward firmly near the LATCH attachment path. The child
in the center of the child restraint with your restraint should not move more than 1 inch
knee to compress the vehicle seat cushion (25 mm), from side to side. Try to tug it
and seatback while tightening the webbing forward and check to see if the LATCH
of the anchor attachments. attachment holds the restraint in place. If the
5. Tighten the tether strap according to the restraint is not secure, tighten the LATCH
manufacturer’s instructions to remove any attachment as necessary, or put the restraint
slack. in another seat and test it again. You may
need to try a different child restraint. Not all
child restraints fit in all types of vehicles.
7. Check to make sure the child restraint is
properly secured prior to each use. If the
Safety — Seats, seat belts and supplemental restraint system 1-29
in a collision. FORWARD-FACING CHILD RE-
STRAINT INSTALLATION USING THE
The child restraint top tether strap must be used SEAT BELTS
when installing the child restraint with the
LATCH lower anchor attachments. WARNING
First, secure the child restraint with the LATCH
lower anchors (rear outboard seat positions The three-point seat belt with Auto-
only). matic Locking Retractor (ALR) must be
1. Remove the head restraint and store it in a used when installing a child restraint.
secure place. Be sure to reinstall the head Failure to use the ALR mode will result
restraint when the child restraint is removed in the child restraint not being properly
(rear outboard seat positions). secured. The restraint could tip over or
JVR0274X be loose and cause injury to a child in a
See “Head restraints/headrests” (P.1-5) for
sudden stop or collision. Also, it can
head restraint adjustment, removal and
Installing top tether strap change the operation of the front
installation information.
passenger air bag. See “Front passen-
Position the top tether strap over the top of ger air bag and status light” (P.1-46).
WARNING the seatback.
2. Secure the top tether strap to the tether
Child restraint anchorages are de- anchor point on the back of the seatback
signed to withstand only those loads behind the child restraint.
imposed by correctly fitted child re-
straints. Under no circumstances are 3. Refer to the appropriate child restraint
they to be used to attach adult seat installation procedure steps in this section
belts, or other items or equipment to before tightening the tether strap.
the vehicle. Doing so could damage the If you have any questions when installing a
child restraint anchorages. The child top tether strap, consult your NISSAN
restraint will not be properly installed dealer for details.
using the damaged anchorage, and a
child could be seriously injured or killed
1-30 Safety — Seats, seat belts and supplemental restraint system
rear seats or in the front passenger seat:
1. If you must install a child restraint in
the front seat, it should be placed in a
forward-facing direction only. Move the
seat to the rearmost position. Child
restraints for infants must be used in
the rear-facing direction and, therefore,
must not be used in the front seat.
2. Position the child restraint on the seat.
Always follow the child restraint manufac-
turer’s instructions.
The back of the child restraint should be
SSS0640 secured against the vehicle seatback. SSS0360B
Forward-facing (front passenger seat) — step 1 If necessary, adjust or remove the head Forward-facing — step 3
Refer to all Warnings and Cautions in the “Child restraint to obtain the correct child restraint 3. Route the seat belt tongue through the child
safety” and “Child restraints” sections before fit. If the head restraint is removed, store it in restraint and insert it into the buckle until you
installing a child restraint. a secure place. Be sure to reinstall the hear and feel the latch engage. Be sure to
NISSAN does not recommend the use of the head restraint when the child restraint follow the child restraint manufacturer’s
lower anchors if the combined weight of the is removed. See “Head restraints/head- instructions for belt routing.
child and the child restraint exceeds 65 lbs rests” (P.1-5) for head restraint adjustment, If the child restraint is equipped with a top
(29.5 kg). If the combined weight of the child removal and installation information. tether strap, route the top tether strap and
and the child restraint is greater than 65 lbs If the seating position does not have an secure the tether strap to the tether anchor
(29.5 kg), use the vehicle’s seat belt (not the adjustable head restraint and it is interfering point (rear seat installation only). See
lower anchors) to install the child restraint. Be with the proper child restraint fit, try another “Installing top tether strap” (P.1-34). Do
sure to follow the child restraint manufacturer’s seating position or a different child restraint. not install child restraints that require the
instructions for installation. use of a top tether strap in seating positions
Follow these steps to install a forward-facing that do not have a top tether anchor.
child restraint using the vehicle seat belt in the
SSS0641 SSS1135
Forward-facing — step 8 Forward-facing — step 10
8. After attaching the child restraint, test it 10. If the child restraint is installed in the front
before you place the child in it. Push it from passenger seat, place the ignition switch in
side to side while holding the child restraint the ON position. The front passenger air bag
near the seat belt path. The child restraint status light should illuminate. If this light
should not move more than 1 inch (25 mm), is not illuminated, see “Front passenger air
from side to side. Try to tug it forward and bag and status light” (P.1-46). Move the
check to see if the belt holds the restraint in child restraint to another seating posi-
place. If the restraint is not secure, tighten tion. Have the system checked by a
the seat belt as necessary, or put the NISSAN dealer.
restraint in another seat and test it again. After the child restraint is removed and the seat
You may need to try a different child belt is fully retracted, the ALR mode (child
restraint. Not all child restraints fit in all restraint mode) is canceled.
types of vehicles.
9. Check to make sure the child restraint is
properly secured prior to each use. If the
Safety — Seats, seat belts and supplemental restraint system 1-33
in a collision. BOOSTER SEATS
Precautions on booster seats
The child restraint top tether strap must be used
when installing the child restraint with the seat
belts. WARNING
First, secure the child restraint with the seat belt.
If a booster seat and seat belt are not
1. Remove the head restraint and store it in a used properly, the risk of a child being
secure place. Be sure to reinstall the head injured in a sudden stop or collision
restraint when the child restraint is removed greatly increases:
(rear outboard seat positions).
. Make sure the shoulder portion of
See “Head restraints/headrests” (P.1-5) for the belt is away from the child’s face
head restraint adjustment, removal and and neck and the lap portion of the
JVR0274X
installation information. belt does not cross the stomach.
Installing top tether strap Position the top tether strap over the top of . Make sure the shoulder belt is not
the seatback. behind the child or under the child’s
2. Secure the top tether strap to the tether arm.
WARNING anchor point on the back of the seatback . A booster seat must only be in-
behind the child restraint. stalled in a seating position that has
Child restraint anchorages are de-
signed to withstand only those loads 3. Refer to the appropriate child restraint a lap/shoulder belt.
imposed by correctly fitted child re- installation procedure steps in this section
straints. Under no circumstances are before tightening the tether strap.
they to be used to attach adult seat If you have any questions when installing a
belts, or other items or equipment to top tether strap, consult your NISSAN
the vehicle. Doing so could damage the dealer for details.
child restraint anchorages. The child
restraint will not be properly installed
using the damaged anchorage, and a
child could be seriously injured or killed
1-34 Safety — Seats, seat belts and supplemental restraint system
LRS0455 LRS0453 LRS0464
Booster seats of various sizes are offered by . Make sure the child’s head will be properly All U.S. states and Canadian provinces or
several manufacturers. When selecting any supported by the booster seat or vehicle territories require that infants and small
booster seat, keep the following points in mind: seat. The seatback must be at or above the children be restrained in an approved child
. Choose only a booster seat with a label center of the child’s ears. For example, if a restraint at all times while the vehicle is
certifying that it complies with Federal Motor low back booster seat * 1 is chosen, the being operated.
Vehicle Safety Standard 213 or Canadian vehicle seatback must be at or above the The instructions in this section apply to booster
Motor Vehicle Safety Standard 213. center of the child’s ears. If the seatback is seat installation in the rear seats or the front
. Check the booster seat in your vehicle to be lower than the center of the child’s ears, a passenger seat.
sure it is compatible with the vehicle’s seat high back booster seat * 2 should be used.
. If the booster seat is compatible with your Booster seat installation
and seat belt system.
vehicle, place your child in the booster seat
and check the various adjustments to be
sure the booster seat is compatible with
CAUTION
your child. Always follow all recommended Do not use the lap/shoulder belt Auto-
procedures. matic Locking Retractor (ALR) mode
Safety — Seats, seat belts and supplemental restraint system 1-35
when using a booster seat with the seat
belts.
SSS0640 LRS0454
Front passenger position
1. If you must install a booster seat in the
3. The booster seat should be positioned on
front seat, move the seat to the rear-
the vehicle seat so that it is stable.
most position.
If necessary, adjust or remove the head
2. Position the booster seat on the seat. Only
restraint to obtain the correct booster seat
place it in a forward-facing direction. Always
fit. If the head restraint is removed, store it in
follow the booster seat manufacturer’s
a secure place. Be sure to reinstall the
instructions.
head restraint when the booster seat is
removed. See “Head restraints/headrests”
(P.1-5) for head restraint adjustment, re-
moval and installation information.
If the seating position does not have a head
restraint and it is interfering with the proper
booster seat fit, try another seating position
or a different booster seat.
SSS0009 SSS0100
WARNING
Front seat-mounted side-impact sup-
plemental air bags and roof-mounted
curtain side-impact supplemental air
bags:
. The side air bags and curtain air
bags ordinarily will not inflate in the
event of a frontal impact, rear im-
pact, rollover or lower severity side
collision. Always wear your seat
SSS0162 belts to help reduce the risk or
SSS0188A severity of injury in various kinds
of accidents.
1-42 Safety — Seats, seat belts and supplemental restraint system
. The seat belts, the side air bags and
curtain air bags are most effective
when you are sitting well back and
upright in the seat. The side air bag
and curtain air bag inflate with great
force. Do not allow anyone to place
their hand, leg or face near the side
air bag on the side of the seatback
of the front seat or near the side
roof rails. Do not allow anyone
sitting in the front seats or rear
outboard seats to extend their hand
out of the window or lean against
the door. Some examples of dan-
gerous riding positions are shown
in the previous illustrations.
. When sitting in the rear seat, do not
hold onto the seatback of the front
seat. If the side air bag inflates, you
may be seriously injured. Be espe-
cially careful with children, who
should always be properly re-
strained. Some examples of danger-
ous riding positions are shown in
the illustrations.
. Do not use seat covers on the front
seatbacks. They may interfere with
side air bag inflation.
WARNING
To ensure proper operation of the
passenger’s advanced air bag system,
please observe the following items.
. Do not allow a passenger in the rear
seat to push or pull on the seatback
pocket.
. Do not place heavy loads heavier
than 9 lbs. (4 kg) on the seatback,
head restraint or in the seatback
pocket.
. Do not store luggage behind the
seat that can press into the seat-
back.
. Confirm the operating condition
JVR0272X with the front passenger air bag
status light.
1. Crash zone sensor 6. Roof-mounted curtain side-impact supplemental
air bag inflators . If you notice that the front passen-
2. Supplemental front-impact air bag modules
7. Roof-mounted curtain side-impact supplemental ger air bag status light is not
3. Front seat-mounted side-impact supplemental
air bag modules air bags modules operating, please take your vehicle
4. Occupant classification sensors (weight sen- 8. Seat belt with pretensioners to your NISSAN dealer to check the
sors) 9. Satellite sensors occupant classification system.
5. Occupant classification system control unit 10. Air bag Control Unit (ACU)
WARNING
SSS1020 SPA1097
If the supplemental air bag warning
SUPPLEMENTAL AIR BAG WARNING SUPPLEMENTAL AIR BAG WARNING light is on, it could mean that the front
LABELS LIGHT air bag, side air bag, curtain air bag
Warning labels about the supplemental front- The supplemental air bag warning light, display- and/or pretensioner systems will not
impact air bag system are placed in the vehicle ing in the instrument panel, monitors the operate in an accident. To help avoid
as shown in the illustration. circuits for the air bag systems, pretensioners injury to yourself or others, have your
and all related wiring. vehicle checked by a NISSAN dealer as
*
1 SRS air bag
soon as possible.
When the ignition switch is in the ON position,
The warning labels are located on the surface of
the supplemental air bag warning light illumi-
the sun visors.
nates for about 7 seconds and then turns off. REPAIR AND REPLACEMENT PRO-
This means the system is operational. CEDURE
If any of the following conditions occur, the air The front air bags, side air bags, curtain air bags
bag and/or pretensioner systems need servi- and pretensioners are designed to activate on a
cing: one-time-only basis. As a reminder, unless it is
damaged, the supplemental air bag warning light
will remain illuminated after inflation has oc-
1-52 Safety — Seats, seat belts and supplemental restraint system
curred. Repair and replacement of these sys- . If you need to dispose of a supple-
tems should be done only by a NISSAN dealer. mental air bag or pretensioner or
When maintenance work is required on the scrap the vehicle, contact a NISSAN
vehicle, the front air bags, side air bags, curtain dealer. Correct supplemental air
air bags and pretensioners and related parts bag and pretensioner system dis-
should be pointed out to the person performing posal procedures are set forth in the
the maintenance. The ignition switch should appropriate NISSAN Service Man-
always be in the LOCK position when working ual. Incorrect disposal procedures
under the hood or inside the vehicle. could cause personal injury.
WARNING
. Once a front air bag, side air bag or
curtain air bag has inflated, the air
bag module will not function again
and must be replaced. Additionally,
the activated pretensioners must
also be replaced. The air bag mod-
ule and pretensioner should be
replaced by a NISSAN dealer. The
air bag modules and pretensioner
system cannot be repaired.
. The front air bag, side air bag and
curtain air bag systems, and preten-
sioner system should be inspected
by a NISSAN dealer if there is any
damage to the front end or side
portion of the vehicle.
JVC0572X
JVC0607X
mode switch
*: if so equipped
The needle indicators may move slightly
after the ignition switch is placed in the
OFF or LOCK position. This is not a
malfunction.
CAUTION
. For cleaning, use a soft cloth, dam-
pened with water. Never use a rough
cloth, alcohol, benzine, thinner or
any kind of solvent or paper towel
with a chemical cleaning agent.
They will scratch or cause discolora-
tion to the lens.
. Do not spray any liquid such as
water on the meter lens. Spraying
liquid may cause the system to
malfunction.
SIC4601
SIC4504 SIC4571
Speedometer Odometer/twin trip odometer
SPEEDOMETER AND ODOMETER Odometer/twin trip odometer
Speedometer The odometer * 1 /twin trip odometer * 2 are
displayed when the ignition switch is in the ON
The speedometer indicates vehicle speed in
position.
miles per hour (MPH) and kilometers per hour
(km/h). The odometer records the total distance the
vehicle has been driven.
The twin trip odometer records the distance of
individual trips.
Changing the display:
Pushing the reset switch * 3 located on the
meter panel changes the display as follows:
TRIP A ? TRIP B ? Trip computer mode ?
TRIP A
2-6 Instruments and controls
position as long as the low tire pressure warning
light remains illuminated.
For more information see “Low tire pressure
warning light” (P.2-15), “Tire Pressure Monitor-
ing System (TPMS)” (P.5-4), and “Wheels and
tires” (P.8-30).
Extended storage fuse warning message
The SHIPPING MODE ON/PUSH STORAGE
FUSE warning message may be displayed if the
extended storage fuse switch is not pushed in
(switched on). When this message is displayed,
push in (switch on) the extended storage fuse
SPA2809 JVI0326X switch to turn off the message. For more
information, see “Extended storage fuse switch”
Loose fuel cap warning message Check tire pressure warning message (P.8-22).
Push the reset switch * A for more than 1 The CHECK TIRE PRES (pressure) warning
second to reset the LOOSE FUEL CAP warning message is displayed when the low tire pressure
message after the fuel cap has been tightened. warning light is illuminated and low tire
For additional information see “Fuel-filler cap” pressure is detected. Check and adjust the tire
(P.3-21) of this manual. pressure to the recommended COLD tire
pressure shown on the Tire and Loading
Information label. The CHECK TIRE PRES
warning message turns off when the low tire
pressure warning light turns off.
The low tire pressure warning light remains
illuminated until the tires are inflated to the
recommended COLD tire pressure. The CHECK
TIRE PRES warning message is displayed each
time the ignition switch is placed in the ON
Instruments and controls 2-7
normal range, reduce vehicle speed to
decrease temperature. If gauge is over
the normal range, stop the vehicle as
soon as safely possible. If the engine is
overheated, continued operation of the
vehicle may seriously damage the en-
gine. See “If your vehicle overheats”
(P.6-10) for immediate action required.
SIC4506 SIC4123
When engine speed approaches the red The engine coolant temperature varies with the
zone, shift to a higher gear or reduce outside air temperature and driving conditions.
engine speed. Operating the engine in
the red zone may cause serious engine
damage. CAUTION
If the gauge indicates engine coolant
temperature near the hot (H) end of the
2-8 Instruments and controls
located on the front passenger’s side of the
vehicle.
CAUTION
. If the vehicle runs out of fuel, the
malfunction indicator light (MIL)
may come on. Refuel as soon as
possible. After a few driving trips,
the light should turn off. If the
light remains on after a few driving
trips, have the vehicle inspected by
SIC4124 a NISSAN dealer. SIC4531
. For additional information, see
FUEL GAUGE “Malfunction Indicator Light (MIL)” VEHICLE INFORMATION DISPLAY
The gauge * 1 indicates the approximate fuel (P.2-18). When the ignition switch is placed in the ON
level in the tank. position, the vehicle information display shows
The gauge may move slightly during braking, the following information:
turning, acceleration, or going up or down hills. 1. Outside air temperature
2. Continuously Variable Transmission (CVT) posi-
Refill the fuel tank before the gauge
tion indicator (if so equipped)
registers 0 (empty).
3. Odometer/Instrument brightness control display
The low fuel warning light illuminates when 4. Twin trip odometer/Trip computer
the amount of fuel in the tank is getting low.
Refuel as soon as it is convenient, preferably
before the gauge reaches 0. There will be a
small reserve of fuel in the tank when the fuel
gauge reaches 0.
The indicates that the fuel-filler door is
P position selecting warning light* Front passenger air bag status light
Brake warning light
Seat belt warning light High beam indicator light
Charge warning light Supplemental air bag warning light Malfunction Indicator Light (MIL)
Door open warning light Vehicle Dynamic Control (VDC) warning light Security indicator light
All-Wheel Drive (AWD) indicator light (AWD Turn signal/hazard indicator lights
Electric power steering warning light
model)*
All-Wheel Drive (AWD)-V indicator light Vehicle Dynamic Control (VDC) off indicator
Engine oil pressure warning light light
(AWD model)*
Continuously Variable Transmission (CVT) *: if so equipped
Intelligent Key system warning light*
indicator light*
SIC4558 SIC4559
1. Press the Drive Mode Select button. 4. Turn the Selection dial to select the day of
2. Press the SETUP button. the week, then press the ENTER button to
apply the selection.
3. Turn the Selection dial to “Clock Time
Setting”, then press the ENTER button. 5. Turn the Selection dial to select the hour and
AM or PM, then press the ENTER button to
apply the selection.
6. Turn the Selection dial to select the minutes,
then press the ENTER button to apply the
selection.
Select Language 4. Turn the Selection dial to select the pre- Select Units
ferred language, then press the ENTER
1. Press the Drive Mode Select button. 1. Press the Drive Mode Select button.
button to apply the selection.
2. Press the SETUP button. 2. Press the SETUP button.
3. Turn the Selection dial to “Select Lan- 3. Turn the Selection dial to “Select Units” then
guage”, then press the ENTER button. press the ENTER button.
4. Turn the Selection dial to select “US” or Auto Interior Illumination Selective Door Unlock
“METRIC”, then press the ENTER button to
Select to turn the illumination of the interior When this item is turned on, only the driver’s
apply the selection.
lights on or off when any door is unlocked. door is unlocked after the door unlock operation
1. Press the Drive Mode Select button. is performed once. All of the doors can be
unlocked if the door unlock operation is per-
2. Press the SETUP button.
formed again within 1 minute.
3. Turn the Selection dial to “Auto Interior
When this item is turned off, all the doors will be
Illumination” then press the ENTER button.
unlocked after the door unlock operation is
4. Turn the Selection dial to select “ON” or performed once.
“OFF”, then press the ENTER button to
1. Press the Drive Mode Select button.
apply the selection.
2. Press the SETUP button.
3. Turn the Selection dial to “Selective Door
Unlock” then press the ENTER button.
SIC4607 SIC4583
JVI0324X SIC4618
CAUTION
Do not adjust the display controls while
driving so that full attention may given
to vehicle operation.
SIC4563
Daily Reset
Records of up to the past 4 days of fuel
consumption can be shown on the display.
service as soon as possible. Please bring reservoir tank. Do not use the
all registered keys that you have when WARNING window washer reservoir tank to
visiting a NISSAN dealer for service. mix the washer fluid concentrate
In freezing temperatures the washer and water.
solution may freeze on the windshield
and obscure your vision which may lead If the windshield wiper operation is inter-
to an accident. Warm windshield with rupted by snow or ice, the wiper may stop
the defroster before you wash the moving to protect its motor. If this occurs,
windshield. turn the wiper switch to the OFF position
and remove the snow or ice that is on and
around the wiper arms. In approximately 1
minute, turn the switch on again to operate
CAUTION the wiper.
. Do not operate the washer continu-
ously for more than 30 seconds.
. Do not operate the washer if the
reservoir tank is empty.
. Do not fill the window washer
reservoir tank with washer fluid
concentrates at full strength. Some
methyl alcohol based washer fluid
concentrates may permanently stain
the grille if spilled while filling the
window washer reservoir tank.
. Pre-mix washer fluid concentrates
with water to the manufacturer’s
recommended levels before pouring
the fluid into the window washer
SIC3664
CAUTION
The windshield wiper and washer operates . This function can be operated even
when the ignition switch is in the ON position. if the ignition switch is in the “ON”
Push the lever down to operate the wiper at the position. However, to prevent an
following speed: accident or damage when pulling
*
1 Intermittent — intermittent operation can be
up the wiper arm, be sure to observe
adjusted by turning the knob toward A * the following precautions.
*
(Slower) or B (Faster). — Make sure the shift lever is in
*
2 Low — continuous low speed operation the P (Park) position (Continu-
*
3 High — continuous high speed operation ously Variable Transmission
Push the lever up * 4 to have one sweep models).
operation of the wiper. — Make sure the shift lever is in
Pull the lever toward you * 5 to operate the the N (Neutral) position, with the
washer. Then the wiper will also operate several parking brake fully applied
times. (Manual Transmission models).
the grille if spilled while filling the Push the switch forward * 3 to operate the
window washer reservoir tank. washer. Then the wiper will also operate several
times.
. Pre-mix washer fluid concentrates
with water to the manufacturer’s
recommended levels before pouring
the fluid into the window washer
reservoir tank. Do not use the
CAUTION
When cleaning the inner side of the rear
window, be careful not to scratch or
SIC4520 damage the rear window defroster. SIC3668
Type A
HEADLIGHT SWITCH
Lighting
*
1 Turn the switch to the position:
The front parking, side marker, tail, license plate,
instrument lights and daytime running lights (for
NISMO models) will come on.
*
2 Turn the switch to the position:
Headlights will come on and all the other lights
remain on. However, the daytime running lights
(for NISMO models) will turn off.
SIC4519
Type B
SIC3669 SAA1232
Autolight system (if so equipped) Be sure not to put anything on top of the
photo sensor * 1 located on the top of the
The autolight system allows the headlights to be
instrument panel. The photo sensor con-
set so they turn on and off automatically.
trols the autolight; if it is covered, the
To set the autolight system: photo sensor reacts as if it is dark and the
1. Make sure the headlight switch is in the headlights will illuminate.
AUTO position *
1 .
Automatic headlights off delay
2. Place the ignition switch in the ON position.
You can keep the headlights on for up to 45
3. The autolight system automatically turns the seconds after you place the ignition switch in
headlights on and off. OFF and open any door then close all the doors.
To turn the autolight system off, turn the switch
to the OFF, or position.
The autolight system can turn on the headlights
automatically when it is dark and turn off the
SIC4517 SIC3671
SIC4129
FOG LIGHT SWITCH (if so equipped) To sound the horn, push the center pad area of The vehicle should be driven with the Vehicle
To turn the fog lights on, turn the headlight the steering wheel. Dynamic Control (VDC) system on for most
switch to the position, then turn the switch driving conditions.
to the position. To turn them off, turn the WARNING If the vehicle is stuck in mud or snow, the VDC
switch to the OFF position. system reduces the engine output to reduce
The headlights must be on for the fog lights to Do not disassemble the horn. Doing so wheel spin. The engine speed will be reduced
operate. could affect proper operation of the even if the accelerator is depressed to the floor.
supplemental front air bag system. If maximum engine power is needed to free a
When the headlight switch is in the AUTO stuck vehicle, turn the VDC system off.
position, turning the fog light switch to the Tampering with the supplemental front
position will turn on the headlights, fog lights air bag system may result in serious To turn off the VDC system, push the VDC OFF
and the other lights while the ignition switch is in personal injury. switch. The indicator light will illuminate.
the ON position or the engine is running. Push the VDC OFF switch again or restart the
engine to turn on the system. (See “Vehicle
Dynamic Control (VDC) system” (P.5-41).)
CAUTION SIC2770
. The battery could run down if the The seats are warmed by built-in heaters. The
seat heater is operated while the switches located on the center console can be
engine is not running. operated independently of each other.
. Do not use the seat heater for 1. Start the engine.
extended periods or when no one 2. Select heat range.
is using the seat. *
1 For high heat, push the HI (High) side of
. Do not put anything on the seat the switch.
which insulates heat, such as a *
2 For low heat, push the LO (Low) side of
blanket, cushion, seat cover, etc. the switch.
Otherwise, the seat may become
overheated.
The indicator light in the switch *
3 will
illuminate when the heater is on.
. Do not place anything hard or heavy
on the seat or pierce it with a pin or 3. To turn off the heater, return the switch to
similar object. This may result in the level position. Make sure the indicator
light goes off.
2-40 Instruments and controls
CLOCK (if so equipped)
The heater is controlled by a thermostat, The digital clock (in the audio unit) displays time
automatically turning the heater on and off. when the ignition switch is in the ACC or ON
The indicator light will remain on as long as position. The clock ON or OFF mode can be
the switch is on. selected. For details of the digital clock in the
When the vehicle’s interior is warmed, or NAVIGATION SYSTEM, refer to “Clock” (P.4-8).
before you leave the vehicle, be sure to turn If the power supply is disconnected, the
off the switch. clock will not indicate the correct time.
Readjust the time.
SIC4131
CAUTION
. The outlet and plug may be hot
during or immediately after use.
. Do not use with accessories that
exceed a 12 volt, 120W (10A) power
draw. Do not use double adapters or
more than one electrical accessory.
. Use power outlet with the engine
running to avoid discharging the
vehicle battery.
CAUTION
. Do not use bottle holder for any
other objects that could be thrown
about in the vehicle and possibly
injure people during sudden braking
or an accident.
. Do not use bottle holder for open
liquid containers.
SIC4527 SIC4529
Center console
CARGO FLOOR BOX
1. To open the cargo floor box, pull the board
*A .
SIC4528
Door (front and rear)
WARNING
. Never put anything on the cargo
cover, no matter how small. Any
object on it could cause an injury
in an accident or sudden stop.
. Do not leave the cargo cover in the
vehicle with it disengaged from the
holder.
. The child restraint top tether strap
SIC4526 SIC3505 may be damaged by contact with
the cargo cover or items in the
GLOVE BOX COAT HOOK
luggage area. Remove the cargo
The coat hook is located above the rear side cover from the vehicle or secure it
WARNING window. and any luggage. Your child could
be seriously injured or killed in a
Keep glove box lid closed while driving CAUTION collision if the top tether strap is
to help prevent injury in an accident or a damaged.
sudden stop. Do not apply a total load of more than 2
kg (4 lb) to the hook. The cargo cover keeps the luggage compart-
To open the glove box, pull the handle. ment contents hidden from the outside.
To close, push the lid in until the lock latches.
The glove box light illuminates when the head-
light switch is turned on.
SIC4533 SIC4523
POWER MOONROOF
WARNING The moonroof only operates when the ignition
switch is in the ON position.
. In an accident you could be thrown The moonroof is operational for about 45
from the vehicle through an open seconds, even if the ignition switch is turned to
moonroof. Always use seat belts the OFF position. If the driver’s door or the
and child restraints. passenger’s door is opened during this period of
. Do not allow anyone to stand up or about 45 seconds, power to the moonroof is
extend any portion of their body out canceled.
of the moonroof opening while the
vehicle is in motion or while the Sunshade
moonroof is closing. The sunshade will open automatically when the
moonroof is opened. However, it must be closed
SIC4624
manually.
CAUTION Sliding the moonroof
To fully open or close the moonroof, push the
. Remove water drops, snow, ice or switch toward *1 or *2 and release
sand from the moonroof before it; it need not be held. The roof will automatically
opening. open or close all the way. To stop the roof, push
. Do not place any heavy object on the switch in any direction while it is opening or
the moonroof or surrounding area. closing.
Tilting the moonroof
To tilt up, first close the moonroof by pushing the
switch toward *2 . Push the switch toward
*2 again and release it; it need not be
held. To tilt down the moonroof, push the switch
toward * 1 .
Keys .............................................................................................. 3-2 Warning lights and audible reminders ...................... 3-14
NISSAN Vehicle Immobilizer System keys ................... 3-2 Troubleshooting guide .................................................. 3-15
Intelligent Keys (if so equipped) ..................................... 3-3 How to use remote keyless entry function .............. 3-16
Doors ............................................................................................ 3-4 Hood ......................................................................................... 3-19
Locking with key .................................................................. 3-5 Lift gate .................................................................................... 3-20
Locking with inside lock knob .......................................... 3-5 Front side and rear unique parts (NISMO models) ..... 3-20
Locking with power door lock switch ............................ 3-5 Fuel-filler door ........................................................................ 3-21
Automatic door locks ......................................................... 3-6 Opening the fuel-filler door ......................................... 3-21
Child safety rear door lock ............................................... 3-6 Fuel-filler cap .................................................................. 3-21
Remote keyless entry system (if so equipped) ................. 3-7 Tilt steering column .............................................................. 3-23
How to use remote keyless entry system ..................... 3-8 Tilt operation ................................................................... 3-24
Intelligent Key system (if so equipped) ............................ 3-10 Sun visors ................................................................................ 3-24
Intelligent Key operating range ..................................... 3-12 Mirrors ..................................................................................... 3-25
Door locks/unlocks precaution ..................................... 3-12 Inside mirror ..................................................................... 3-25
Intelligent Key operation ................................................. 3-13 Outside mirrors ............................................................... 3-25
Battery saver system ....................................................... 3-14 Vanity mirror ..................................................................... 3-27
KEYS
A key number plate is supplied with your keys. duplicate your existing key. As many as 5 keys
Record the key number and keep it in a safe can be used with one vehicle. You should bring
place (such as your wallet), not in the vehicle. If all the registered keys that you have to a
you lose your keys, see a NISSAN dealer for NISSAN dealer for registration. This is because
duplicates by using the key number. NISSAN the registration process will erase the memory of
does not record any key numbers so it is very all key codes previously registered into the
important to keep track of your key number plate. NISSAN Vehicle Immobilizer System. After the
registration process, these components will only
A key number is only necessary when you have
recognize keys coded into the NISSAN Vehicle
lost all keys and do not have one to duplicate
Immobilizer System during registration. Any key
from. If you still have a key, this key can be
that is not given to your dealer at the time of
duplicated by a NISSAN dealer.
registration will no longer be able to start your
vehicle.
SPA2405
CAUTION WARNING
Always carry the mechanical key in- . Always have the doors locked while
stalled in the Intelligent Key. driving. Along with the use of seat
belts, this provides greater safety in
the event of an accident by helping
to prevent persons from being
thrown from the vehicle. This also
helps keep children and others from
unintentionally opening the doors,
and will help keep out intruders.
. Before opening any door, always
SPA2033
look for and avoid oncoming traffic.
Mechanical key . Do not leave children unattended
To remove the mechanical key, release the lock inside the vehicle. They could un-
knob at the back of the Intelligent Key. knowingly activate switches or con-
trols. Unattended children could
To install the mechanical key, firmly insert it into become involved in serious acci-
the Intelligent Key until the lock knob returns to dents.
the lock position.
Use the mechanical key to lock or unlock the
doors. (See “Doors” (P.3-4).)
JVP0213X
1. Push the UNLOCK button *
2 on the pushed. (Note: the PANIC button must
keyfob. be pushed for more than 1 second.)
*
1 LOCK button . The driver’s door unlocks.
Battery indicator light
*
2 UNLOCK button . The hazard indicator flashes once if all
*
3 PANIC button The battery indicator light * 4 illuminates when
doors are completely closed.
*
4 Battery indicator light
2. Push the UNLOCK button again within
you push any button. If the light does not
illuminate, the battery is weak or needs replace-
HOW TO USE REMOTE KEYLESS 5 seconds. ment. For information regarding replacement of
ENTRY SYSTEM . All the doors and the lift gate unlock. a battery, see “Key battery replacement” (P.8-
. The hazard indicator flashes once if all 22).
Locking doors
doors are completely closed.
1. Remove the key from the ignition switch.
All doors will be locked automatically unless one
2. Close all the doors.
of the following operations is performed within 1
3. Push the LOCK button *
1 on the minute of pushing the UNLOCK button.
keyfob.
. Opening any door (including the lift gate).
4. All the doors will lock. . Placing the ignition switch in the ON
All of the doors will lock when the LOCK position.
computer.
CAUTION . When the vehicle is parked near a parking
WARNING meter.
. Radio waves could adversely affect . Be sure to carry the Intelligent Key In such cases, correct the operating conditions
electric medical equipment. Those with you when operating the vehi- before using the Intelligent Key function or use
who use a pacemaker should con- cle. the mechanical key.
tact the electric medical equipment . Never leave the Intelligent Key in Although the life of the battery varies depending
manufacturer for the possible influ- the vehicle when you leave the on the operating conditions, the battery’s life is
ences before use. vehicle. approximately 2 years. If the battery is dis-
. The Intelligent Key transmits radio charged, replace it with a new one.
waves when the buttons are The Intelligent Key is always communicating with Since the Intelligent Key is continuously receiv-
pushed. The FAA advises that the the vehicle as it receives radio waves. The ing radio waves, if the key is left near equipment
radio waves may affect aircraft na- Intelligent Key system transmits weak radio which transmits strong radio waves, such as
vigation and communication sys- waves. Environmental conditions may interfere signals from a TV and personal computer, the
tems. Do not operate the with the operation of the Intelligent Key system battery life may become shorter.
Intelligent Key while on an airplane. under the following operating conditions.
For information regarding replacement of a
Make sure the buttons are not . When operating near a location where battery, see “Key battery replacement” (P.8-22).
operated unintentionally when the strong radio waves are transmitted, such
unit is stored during a flight. as a TV tower, power station and broad- As many as 4 Intelligent Keys can be registered
casting station. and used with one vehicle. For information about
the purchase and use of additional Intelligent
The Intelligent Key system can operate all the . When in possession of wireless equipment,
Keys, contact a NISSAN dealer.
door locks using the remote controller function such as a cellular phone, transceiver, and
or pushing the request switch on the vehicle CB radio.
without taking the key out from a pocket or . When the Intelligent Key is in contact with or CAUTION
purse. The operating environment and/or condi- covered by metallic materials.
tions may affect the Intelligent Key system . When any type of radio wave remote control . Do not allow the Intelligent Key,
operation. is used nearby. which contains electrical compo-
Be sure to read the following before using the . When the Intelligent Key is placed near an nents, to come into contact with
Intelligent Key system. electric appliance such as a personal water or salt water. This could affect
3-10 Pre-driving checks and adjustments
the system function. Intelligent Key from the vehicle. This may prevent
the unauthorized use of the Intelligent Key to
. Do not drop the Intelligent Key. operate the vehicle. For information regarding
. Do not strike the Intelligent Key the erasing procedure, contact a NISSAN deal-
sharply against another object. er.
. Do not change or modify the Intel- The Intelligent Key function can be disabled. For
ligent Key. information about disabling the Intelligent Key
. Wetting may damage the Intelligent function, contact a NISSAN dealer.
Key. If the Intelligent Key gets wet,
immediately wipe until it is comple-
tely dry.
. If the outside temperature is below
148F (−108C) degrees, the battery of
the Intelligent Key may not function
properly.
. Do not place the Intelligent Key for
an extended period in an area where
temperatures exceed 1408F (608C).
. Do not attach the Intelligent Key
with a key holder that contains a
magnet.
. Do not place the Intelligent Key near
equipment that produces a mag-
netic field, such as a TV, audio
equipment, personal computers or
cellular phone.
INTELLIGENT KEY OPERATING switches may not function. DOOR LOCKS/UNLOCKS PRECAU-
RANGE When the Intelligent Key is within the operating TION
The Intelligent Key functions can only be used range, it is possible for anyone who does not . Do not push the door handle request switch
when the Intelligent Key is within the specified carry the Intelligent Key to push the request with the Intelligent Key held in your hand as
operating range from the request switch * 1 . switch to lock/unlock the doors including the lift illustrated. The close distance to the door
When the Intelligent Key battery is discharged or gate. handle will cause the Intelligent Key system
strong radio waves are present near the operat- to have difficulty recognizing that the In-
ing location, the Intelligent Key system’s operat- telligent Key is outside the vehicle.
ing range becomes narrower, and the Intelligent . After locking with the door handle request
Key may not function properly. switch, verify the doors are securely locked
by testing them.
The operating range is within 31.50 in (80 cm)
from each request switch * 1 . . To prevent the Intelligent Key from being left
inside the vehicle, make sure you carry the
If the Intelligent Key is too close to the door key with you and then lock the doors.
glass, handle or rear bumper, the request
SPA2408 SPA2545
Switching procedure:
To switch the hazard indicator and horn (chime)
operation, push the LOCK *1 and UN-
LOCK *
2 buttons on the Intelligent Key
simultaneously for more than 2 seconds.
. When the hazard indicator mode is set, the
hazard indicator flashes 3 times.
. When the hazard indicator and horn mode is
set, the hazard indicator flashes once and
the horn chirps once.
WARNING
. Make sure the hood is completely
closed and latched before driving.
Failure to do so could cause the
hood to fly open and result in an
accident.
. If you see steam or smoke coming
from the engine compartment, to
avoid injury do not open the hood.
SPA2798
fuel cap.
WARNING
Do not adjust the steering wheel while
driving. You could lose control of your
vehicle and cause an accident.
SPA2809
CAUTION
. Do not store the main sun visor
before storing the extension sun
visor.
. Do not pull the extension sun visor
forcedly downward.
SIC3451
3-24 Pre-driving checks and adjustments
MIRRORS
OUTSIDE MIRRORS
WARNING
Objects viewed in the outside mirror on
the passenger side are closer than they
appear. Be careful when moving to the
right. Using only this mirror could cause
an accident. Use the inside mirror or
glance over your shoulder to properly
judge distances to other objects.
SPA2447 SPA2143
INSIDE MIRROR The night position *1 will reduce glare from the
headlights of vehicles behind you at night.
Adjust the angle of the inside mirror to the
desired position. Use the day position *
2 when driving in daylight
hours.
WARNING
Use the night position only when ne-
cessary, because it reduces rear view
clarity.
SPA2214 SPA1829
VANITY MIRROR
To use the front vanity mirror, pull down the sun
visor and pull up the cover.
WARNING
. Do not disassemble or modify this
system. If you do, it may result in
accidents, fire, or electric shock.
. Do not use this system if you notice
any abnormality, such as a frozen
screen or lack of sound. Continued
use of the system may result in
accident, fire or electric shock.
. In case you notice any foreign
object in the system hardware, spill
liquid on it, or notice smoke or smell
coming from it, stop using the
system immediately and contact
your nearest NISSAN dealer. Ignor-
ing such conditions may lead to
accidents, fire, or electric shock.
Adjusting the item: Other items are adjusted by selecting one of a Inputting characters:
For screens where an item can be adjusted set number of conditions. For example, the Touch the letter key *
1 .
incrementally, such as when adjusting the bass Display Mode can be set to “Automatic”, “Day”
or “Night”. To adjust this type of item, touch the There are some options available when inputting
and treble for the audio system, touch the “+”
key *1 or the “−” key *2 to adjust the settings
item * 1 . The item will cycle through the
characters.
available settings and the red indicator lights . 123/ABC:
of an item.
to the left of the setting condition *2 will come Changes the available character set to
When there are more items than can be on or turn off accordingly. numbers.
displayed on one screen, touch the up arrow
.
*3 to scroll up the page or touch the down
Space:
arrow *4 to scroll down the page. Inserts a space.
. Delete:
Deletes the last inputted character with one
touch. Touch and hold the “Delete” key to
delete all of the characters.
SAA3393
Clock:
Select the “Clock” key to adjust the time and the
appearance of the clock on the display. The
following settings can be adjusted:
. Time Format:
The clock can be set to 12 hours or 24 hours.
. Use GPS Clock:
When this setting is activated, the clock is set
and continually updated via the GPS used by
the Navigation System.
. Set Clock Manually:
When this setting is activated, the clock can be
set manually. Touch the “+” or “−” key to adjust
the hours and minutes up or down.
4-8 Heater, air conditioner, audio and phone systems
(such as the button) is pushed and held for
two seconds.
Reset all settings/memory:
Select the “Reset All Settings/Memory” key to
return all settings to default and to clear the
memory.
Traffic Info setup
Refer to the separate Navigation System Own-
er’s Manual for information regarding this item.
SAA3395
Language:
Select the “Language” key to adjust the
language used by the system. The language
can be set to English, Français or Español.
Touch click:
Select the “Touch Click” key to toggle the touch
click feature on or off. When activated, a click
sound will be heard every time a key on the
screen is touched.
Beep tones:
Select the “Beep Tones” key to toggle the beep
tones feature on or off. When activated, a beep
sound will be heard when a pop-up message
appears on the screen or a button on the unit
Heater, air conditioner, audio and phone systems 4-9
CONTROL PANEL BUTTONS —
COLOR SCREEN (Type B)
CAUTION
. The glass screen on the liquid
crystal display may break if it is hit
with a hard or sharp object. If the
glass screen breaks, do not touch it.
Doing so could result in an injury.
JVH0733X . To clean the display, never use a
rough cloth, alcohol, benzine, thin-
1. MAP button* 7. ON·OFF button/VOL (volume) control knob ner or any kind of solvent or paper
2. Display screen (P.4-15) towel with a chemical cleaning
3. button (P.4-85) 8. CAMERA button (P.4-15) agent. They will scratch or deterio-
4. button (P.4-12) 9. NAV button* rate the panel.
5. (brightness control) button (P.4-6) *For information regarding the Navigation sys- . Do not splash any liquid such as
6. BACK button (P.4-11) tem control buttons, refer to the separate water or car fragrance on the dis-
Navigation System Owner’s Manual. play. Contact with liquid will cause
4-10 Heater, air conditioner, audio and phone systems
the system to malfunction. . 123/ABC:
Changes the keyboard between numbers
To help ensure safe driving, some functions and alphabets.
cannot be operated while driving. . Space:
The on-screen functions that are not available Inserts a space.
while driving will be “grayed out” or muted. . Delete:
Park the vehicle in a safe location and then Deletes the last inputted character with one
operate the navigation system. touch. Touch and hold the “Delete” key to
delete all of the characters.
. OK:
WARNING Completes the character input.
. ALWAYS give your full attention to JVH0734X
Touch screen maintenance
driving. If you clean the display screen, use a dry, soft
. Avoid using vehicle features that Touch screen operation cloth. If additional cleaning is necessary, use a
could distract you. If distracted, small amount of neutral detergent with a soft
Selecting the item:
you could lose control of your cloth. Never spray the screen with water or
vehicle and cause an accident. Touch an item to select. To select the “Audio” detergent. Dampen the cloth first and then wipe
key, touch the “Audio” key *
1 on the screen. the screen.
Adjusting the item: HOW TO USE THE BACK BUTTON
Touch the “+” key or the “−” key to adjust the Push the BACK button to return to the previous
settings of an item. Touch the up arrow to scroll screen.
up the page. Touch the down arrow to scroll
down the page.
Inputting characters:
Touch the letter or number key. There are some
options available when inputting characters.
HOW TO USE THE APPS·I BUTTON To select and/or adjust several functions,
For more information about the “SiriusXM Travel features and modes that are available for your
Link”, and “SiriusXM Traffic” features, see the vehicle:
separate Navigation System Owner’s Manual. 1. Push the button.
For more information about the “My Apps” key, 2. Touch the “Settings” key.
see “NissanConnectTM App smartphone inte- 3. Touch the desired item.
gration” (P.4-71).
For more information about the “Voice Com-
mands” key, see “NISSAN voice recognition
system” (P.4-92).
Temperature Unit Touch this key to change the temperature unit being displayed (Fahrenheit or Celsius).
Touchscreen click Toggles the touch-screen click feature on or off. When activated a click sound will be heard every time a key on
the screen is touched.
System Beeps Toggle the system beep tones feature on or off. When activated, a beep sound will be heard when a pop-up
message appears on the screen or a button on the unit (such as the button) is pushed and held for 2
seconds.
Return to Factory Settings / Clear Memory Touch this key to return all settings to default and to clear the memory.
Software Licenses Touch this key to display software licensing information.
Traffic Touch this key to display traffic settings. See the separate Navigation System Owner’s Manual for more
information.
SXM Touch this key to display SXM status information. For SXM setup, see “FM-AM-SAT radio with Compact Disc
(CD) player (Type C)” (P.4-57).
HOW TO USE BRIGHTNESS CON- When the shift lever is shifted into the R
. Underneath the bumper and the
TROL BUTTON (Reverse) position, the monitor display shows
corner areas of the bumper cannot
the view to the rear of the vehicle.
To change the display brightness, push the be viewed on the RearView Monitor
button. Pushing the button again will change the The system is designed as an aid to the driver in because of its monitoring range
display to the day or the night display. situations such as slot parking or parallel limitation. The system will not show
parking. small objects below the bumper,
If no operation is performed within 5 seconds,
the display will return to the previous display. and may not show objects close to
the bumper or on the ground.
Push and hold the button for more than two WARNING
seconds to turn the display off. Push the button . Objects viewed in the RearView
again to turn the display on. Failure to follow the warnings and Monitor differ from actual distance
instructions for proper use of the Rear- because a wide-angle lens is used.
HOW TO USE THE ON·OFF BUTTON/
View Monitor could result in serious . Objects in the RearView Monitor
VOLUME CONTROL KNOB injury or death. will appear visually opposite than
Push the ON·OFF button to turn audio function when viewed in the rear view and
on and off. Turn the volume control knob to . The RearView monitor is a conve-
nience but it is not a substitute for outside mirrors.
adjust audio volume.
proper backing. Always turn and . Make sure that the lift gate is
HOW TO USE THE CAMERA BUTTON look out the windows, and check securely closed when backing up.
For more information regarding the CAMERA mirrors to be sure that it is safe to . Do not put anything on the Rear-
button, see “RearView monitor” (P.4-15). move before operating the vehicle. View camera. The RearView camera
Always back up slowly. is installed above the license plate.
. The system is designed as an aid to . When washing the vehicle with
the driver in showing large station- high-pressure water, be sure not to
ary objects directly behind the vehi- spray it around the camera. Other-
cle, to help avoid damaging the wise, water may enter the camera
vehicle. unit causing water condensation on
. The system cannot completely elim- the lens, a malfunction, fire or an
inate blind spots and may not show electric shock.
every object.
CAUTION
Do not scratch the camera lens when
cleaning dirt or snow from the lens.
SAA2776 JVH0777X
SAA1978 SAA1979
SAA3440 SAA3475
SAA3379
Drive mode screen
SAA1025
Playback order chart
Playback order:
Music playback order of a CD with MP3 or
WMA files is as illustrated.
. The names of folders not containing MP3 or
WMA files are not shown in the display.
*1 Files created with a combination of 48 kHz sampling frequency and 64 kbps bit rate cannot be played.
*2 Protected WMA files (DRM) cannot be played.
*3 Available codes depend on what kind of media, versions and information are going to be displayed.
*4 When VBR files are played, the playback time may not be displayed correctly.
*1 Files created with a combination of 48 kHz sampling frequency and 64 kbps bit rate cannot be played.
*2 Available codes depend on what kind of media, versions and information are going to be displayed.
*1 Files created with a combination of 48 kHz sampling frequency and 64 kbps bit rate cannot be played.
*2 Available codes depend on what kind of media, versions and information are going to be displayed.
SAA2782
Podcast:
ALL REPEAT ↔ TRACK REPEAT
Audiobook:
CD EJECT:
When the CD EJECT button is pushed with the
CD loaded, the CD will be ejected.
When this button is pushed while the CD is
being played, the CD will be ejected.
If the CD comes out and is not removed, it
SAA3401 SAA3402 will be pulled back into the slot to protect
it.
Random: Repeat:
Touch the “Random” key to apply a random play Touch the “Repeat” key to apply a repeat play
pattern to the CD. When the random mode is pattern to the CD. When the repeat mode is
active, the icon will be displayed to the left active, the icon will be displayed to the left
of the song title. If an MP3 CD is playing, of the song title. If an MP3 CD is playing,
touching “Random” alternates between ran- touching “Repeat” alternates between repeating
domly playing songs within the current folder the current song and repeating the current
and songs from the CD as a whole. The folder. The icon is displayed to the left of
icon is displayed to the left of the song title or the song title or folder name to denote which
folder name to denote which pattern is applied. pattern is applied. To cancel Repeat mode,
To cancel Random mode, touch the “Random” touch the “Repeat” key until no icon is
key until no icon is displayed. displayed.
Browse:
Touch the “Browse” key to display the titles on
the CD in list format. Touch the title of a song in
Heater, air conditioner, audio and phone systems 4-51
button when a compatible audio device is
connected into the AUX IN jack.
When the AUX button is pushed with no device
plugged into the jack, the audio system does not
change to the AUX mode.
JVH0370X SAA3444
SAA3491 SAA3445
SAA3492
JVH0751X JVH0735X
JVH0750X SAA0451
4. Touch the “Connect New Device” key. CD/USB MEMORY CARE AND
5. The system acknowledges the command CLEANING
and asks you to initiate connecting from the CD
phone handset. The connecting procedure
of the cellular phone varies according to . Handle a CD by its edges. Never touch the
each cellular phone model. See the cellular surface of the disc. Do not bend the disc.
phone Owner’s Manual for details. You can . Always place the discs in the storage case
also visit www.nissanusa.com/bluetooth for when they are not being used.
instructions on connecting NISSAN recom- . To clean a disc, wipe the surface from the
mended cellular phones. center to the outer edge using a clean, soft
cloth. Do not wipe the disc using a circular
Audio main operation:
motion.
To switch to the Bluetooth® audio mode, push Do not use a conventional record cleaner or
the AUX button repeatedly until the Bluetooth® alcohol intended for industrial use.
audio mode is displayed on the screen.
CAUTION WARNING
. Keep the antenna as far away as . Use a phone after stopping your
possible from the electronic control vehicle in a safe location. If you
modules. have to use a phone while driving,
. Keep the antenna wire more than 8 exercise extreme caution at all
in (20 cm) away from the electronic times so full attention may be given
control system harness. Do not to vehicle operation.
route the antenna wire next to any . If you find yourself unable to devote
harness. full attention to vehicle operation
. Adjust the antenna standing-wave while talking on the phone, pull off
ratio as recommended by the man- the road to a safe location and stop
SAA3446
ufacturer. your vehicle before doing so.
1. Volume control switch −/+
. Connect the ground wire from the
2. PHONE SEND button
CB radio chassis to the body.
3. PHONE END button
. For details, consult a NISSAN deal- CAUTION 4. Microphone
er. Your NISSAN is equipped with the Bluetooth®
To avoid draining the vehicle battery,
use a phone after starting the engine. Hands-Free Phone System. If you have a
compatible Bluetooth® enabled cellular phone,
you can set up the wireless connection between
your cellular phone and the in-vehicle phone
module. With Bluetooth® wireless technology,
you can make or receive a hands-free telephone
call in your vehicle.
Once your cellular phone is connected to the in-
vehicle phone module, no other phone connect-
ing procedure is required. Your phone is
The connecting procedure must be per- “1234” from the handset. The Passkey code the command and announces the next set of
formed when the vehicle is stationary. If “1234” has been assigned by NISSAN and available commands.
the vehicle starts moving during the pro- cannot be changed. 3. Say: “Phone Number” * B . The system
cedure, the procedure will be cancelled. 4. The system asks you to say a name for the acknowledges the command and an-
phone *D . nounces the next set of available commands.
Say: “Special Dialing” to dial more than 10
If the name is too long or too short, the
digits or any special characters.
system tells you, then prompts you for a
name again. 4. Say the number you wish to call starting with
the area code in single digit format. If the
Also, if more than one phone is connected
system has trouble recognizing the correct
and the name sounds too much like a name
phone number, try entering the number in
1. Push the button on the steering wheel. already used, the system tells you, then
the following groups: 3-digit area code, 3-
The system announces the available com- prompts you for a name again.
digit prefix and the last 4-digits. For example,
mands. 555-121-3354 can be said as “five five five”
2. Say: “Connect Phone” * A . The system as the 1st group, then “one two one” as the
acknowledges the command and an- 2nd group, and “three three five four” as the
nounces the next set of available commands. 3rd group. For dialing more than 10 digits or
any special characters, say “Special Dial-
Use the Recent Calls command to access This can be used to reconnect a new phone with
outgoing, incoming or missed calls. the vehicle you have changed your cellular
phone.
“Outgoing” *
A Use the Connect Phone commands to manage
the phones connecting to the vehicle or to
Use the Outgoing command to list the outgoing
enable the Bluetooth® function on the vehicle.
calls made from the vehicle.
“Incoming” *
B
“Add Phone” *
A
Bluetooth® SETTINGS
To access the phone settings:
1. Push the button.
2. Touch the “Settings” key.
3. Touch the “Phone & Bluetooth” key.
PHONE SETTINGS shown in both the vehicle information dis- The NISSAN Voice Recognition system allows
play and the center display screen. hands-free operation of the systems equipped
To access the phone settings:
. Text Messaging: on this vehicle, such as the phone and naviga-
1. Push the button. tion systems.
Touch to toggle the text message function-
2. Touch the “Settings” key. ality on or off. To operate NISSAN Voice Recognition, push the
3. Touch the “Phone & Bluetooth” key. . Show Incoming Text for: button located on the steering wheel.
4. Touch the “Phone Settings” key and adjust Touch “Driver” to have incoming text notifi- When prompted, speak the command for the
the following settings as desired: cations shown in the vehicle information system you wish to activate. The command given
is picked up by the microphone and performed
. Sort Phonebook By: display. Touch “Both” to have text notifica-
tions shown in both the vehicle information when it is properly recognized. NISSAN Voice
Touch “First Name” or “Last Name” to Recognition will provide a voice response as
choose how phonebook entries are alpha- display and the center display screen. Touch
“Off” to turn off all text notifications. well as a message in the center display to inform
betically displayed on the screen. you of the command results.
. Use Phonebook From: . Auto Reply:
Touch “Handset” to use the phone’s phone- Touch to toggle the auto reply functionality
book. Select “SIM” to use the phonebook on on or off.
the SIM card. Touch “Both” to use both . Auto Reply Message:
sources. Touch to indicate preferred message to be
. Download Phonebook Now: sent when “Auto Reply” function is acti-
Touch to download the phonebook to the vated.
vehicle from the chosen source. . Use Vehicle’s Signature:
. Record Name for Phonebook Entry: Touch to toggle on or off the addition of the
Touch to record a name for a phonebook vehicle signature to outgoing messages
entry for use with the NISSAN Voice . Custom Text Messages:
Recognition System. Touch this option to select a custom
. Phone Notifications for: message to edit. There are 4 customer
Touch “Driver” to have phone notifications message slots available.
shown in the vehicle information display.
Touch “Both” to have phone notifications
Precautions when starting and driving ................................ 5-3 Driving the vehicle ................................................................. 5-17
Exhaust gas (carbon monoxide) ...................................... 5-3 Continuously Variable Transmission (CVT) ............. 5-17
Three-way catalyst .............................................................. 5-4 Manual Transmission (MT) ........................................... 5-23
Tire Pressure Monitoring System (TPMS) .................... 5-4 Integrated control system (if so equipped) .................... 5-25
Avoiding collision and rollover ......................................... 5-7 Drive mode ...................................................................... 5-25
Off-road recovery ................................................................ 5-7 Parking brake .......................................................................... 5-29
Rapid air pressure loss ...................................................... 5-7 Cruise control ......................................................................... 5-30
Drinking alcohol/drugs and driving ................................. 5-8 Precautions on cruise control ..................................... 5-30
Driving safety precautions ................................................. 5-8 Cruise control operations ............................................ 5-30
Ignition switch (models without Intelligent Break-in schedule ................................................................. 5-31
Key system) ............................................................................. 5-10 Fuel Efficient Driving Tips ................................................... 5-32
Continuously Variable Transmission (CVT) ................ 5-11 Increasing fuel economy ...................................................... 5-33
Manual Transmission (MT) ............................................. 5-11 All-Wheel Drive (AWD) (if so equipped) ........................ 5-33
Key positions ..................................................................... 5-12 All-Wheel Drive (AWD) mode
Push-button ignition switch (models with Intelligent switch operations ........................................................... 5-33
Key system) ............................................................................. 5-12 AWD warning light ........................................................ 5-35
Operating range for engine start function ................. 5-12 Parking/parking on hills ........................................................ 5-37
Push-button ignition switch operation ........................ 5-13 Electric power steering system ......................................... 5-38
Push-button ignition switch positions ......................... 5-14 Brake system .......................................................................... 5-39
Emergency engine shut off ............................................ 5-14 Braking precautions ...................................................... 5-39
Intelligent Key battery discharge .................................. 5-14 Brake assist ............................................................................ 5-40
Before starting the engine ................................................... 5-15 Brake assist ..................................................................... 5-40
Starting the engine ................................................................ 5-15 Anti-lock Braking System (ABS) ............................... 5-40
Models without Intelligent Key system ....................... 5-15 Vehicle Dynamic Control (VDC) system ......................... 5-41
Models with Intelligent Key system ............................. 5-16 Cold weather driving ............................................................ 5-43
Freeing a frozen door lock ............................................. 5-43 Tire equipment ................................................................ 5-43
Anti-freeze .......................................................................... 5-43 Special winter equipment ............................................ 5-43
Battery ................................................................................. 5-43 Driving on snow or ice ................................................. 5-43
Draining of coolant water ............................................... 5-43 Engine block heater (if so equipped) ....................... 5-44
PRECAUTIONS WHEN STARTING
AND DRIVING
ment even if the other two wheels belted or radial), and tread pattern
are raised off the ground. Make sure on all four wheels. Install traction WARNING
you inform test facility personnel devices on the front wheels when
that your vehicle is equipped with driving on slippery roads and drive Never remove or turn the key to the
AWD before it is placed on a carefully. LOCK position while driving. This may
dynamometer. Using the wrong test . Be sure to check the brakes imme- cause the driver to lose control of the
equipment may result in drivetrain diately after driving in mud or water. vehicle and could result in serious
damage or unexpected vehicle See “Brake system” (P.5-39) for wet vehicle damage or personal injury.
movement which could result in brakes.
serious vehicle damage or personal
. Avoid parking your vehicle on steep
injury.
hills. If you get out of the vehicle
. When a wheel is off the ground due and it rolls forward, backward or
to an unlevel surface, do not spin sideways, you could be injured.
the wheel excessively (AWD model).
. Whenever you drive off-road
. Accelerating quickly, sharp steering through sand, mud or water as deep
maneuvers or sudden braking may as the wheel hub, more frequent
cause loss of control. maintenance may be required. See
. If at all possible, avoid sharp turning the maintenance information in the
maneuvers, particularly at high “NISSAN Service and Maintenance
speeds. Your vehicle has a higher Guide”.
center of gravity than a conventional . Spinning the front wheels on slip-
passenger car. The vehicle is not pery surfaces may cause the AWD
designed for cornering at the same warning light to flash and the AWD
speeds as conventional passenger system to automatically switch from
cars. Failure to operate this vehicle the AWD mode to the 2WD mode.
correctly could result in loss of This could reduce traction. Be espe-
control and/or a rollover accident. cially careful when towing a trailer
. Always use tires of the same type, (AWD model).
size, brand, construction (bias, bias-
5-10 Starting and driving
1. Move the shift lever to the P (Park) position.
2. Turn the ignition switch slightly in the ON
direction.
3. Turn the ignition switch to the LOCK
position.
4. Remove the key.
If the ignition switch is turned to the LOCK
position, the shift lever cannot be moved from
the P (Park) position. The shift lever can be
moved if the ignition switch is in the ON position
with the foot brake pedal depressed.
There is an OFF position * 1 between the
SSD0392 SSD0503
LOCK and ACC positions, although it is not
CONTINUOUSLY VARIABLE TRANS- marked on the ignition switch. MANUAL TRANSMISSION (MT)
MISSION (CVT) The ignition switch includes a device that helps
The ignition lock is designed so that the ignition prevent accidental removal of the key while
switch cannot be turned to the LOCK position driving.
until the shift lever is moved to the P (Park) The key can only be removed when the ignition
position. switch is in the LOCK position.
. When turning the ignition switch to the To turn the ignition switch to the LOCK position
LOCK position, make sure that the shift lever from the ACC or ON position, turn the key to the
is in the P (Park) position. OFF position, push the key in, then turn the key
. When removing the key from the ignition to the LOCK position.
switch, make sure that the shift lever is in the There is an OFF position * 1 in between the
P (Park) position. LOCK and ACC positions. The OFF position is
When the ignition switch cannot be turned to indicated by a “1” on the key cylinder.
the LOCK position:
KEY POSITIONS
LOCK (0) WARNING
The key can only be removed from the ignition Do not operate the push-button ignition
switch at this position. switch while driving the vehicle except
OFF (1) in an emergency. (The engine will stop
when the ignition switch is pushed 3
The engine is turned off. The power supply is
consecutive times or the ignition switch
turned off.
is pushed and held for more than 2
ACC (2) seconds.) If the engine stops while the
The electrical accessory power activates without vehicle is being driven, this could lead
the engine turned on. to a crash and serious injury.
ON (3) SSD0436
Before operating the push-button ignition
The ignition system and the electrical accessory switch, be sure to move the shift lever to the P OPERATING RANGE FOR ENGINE
power activate without the engine turned on. (Park) position (for Continuously Variable Trans- START FUNCTION
mission models) or the shift lever to the N
START (4) (Neutral) position (for manual transmission
The Intelligent Key can only be used for starting
The engine starter activates and the engine will the engine when the Intelligent Key is within the
models).
start. The ignition switch, when released, will specified operating range * 1 .
automatically turn to the ON position. When the Intelligent Key battery is almost
discharged or strong radio waves are present
near the operating location, the Intelligent Key
CAUTION system’s operating range becomes narrower
and may not function properly.
As soon as the engine has started,
If the Intelligent Key is within the operating
release the ignition switch immediately.
range, it is possible for anyone, even someone
who does not carry the Intelligent Key, to push
the ignition switch to start the engine.
4. Push the ignition switch while depressing . Make sure the area around the vehicle is MODELS WITHOUT INTELLIGENT KEY
the brake pedal within 10 seconds after the clear. SYSTEM
chime sounds. The engine will start. . Check fluid levels such as engine oil, cool- 1. Apply the parking brake.
After step 3 is performed, when the ignition ant, brake fluid, and window washer fluid as
2. Continuously Variable Transmission
switch is pushed without depressing the brake frequently as possible, or at least whenever
(CVT) models:
pedal, the ignition switch position will change to you refuel.
. Check that all windows and lights are clean. Move the shift lever to the P (Park) or N
ACC.
(Neutral) position. (P is recommended.)
NOTE: . Visually inspect tires for their appearance
and condition. Also check tires for proper The starter is designed so that it does not
. When the ignition switch is pushed to
inflation. operate unless the shift lever is in either of
the ACC or ON position or the engine is
. Lock all doors. the above positions.
started by the above procedures, the
Intelligent Key system warning light . Position seat and adjust head restraints. Manual Transmission (MT) models:
may blink in yellow even if the Intelli- . Adjust inside and outside mirrors. Move the shift lever to the N (Neutral)
gent Key is inside the vehicle. This is . Fasten seat belts and ask all passengers to position. Depress the clutch pedal fully to
not a malfunction. To stop the warning do likewise. the floor.
light from blinking, touch the ignition
. Check the operation of warning lights when The starter is designed not to operate unless
switch with the Intelligent Key again. the clutch pedal is fully depressed.
the ignition switch is placed in the ON
. If the Intelligent Key system warning position. (See “Warning/indicator lights and 3. Crank the engine with your foot off the
light in the meter is blinking in green, audible reminders” (P.2-12).) accelerator pedal by turning the ignition
replace the battery as soon as possible.
switch to START. Release the switch when
(See “Key battery replacement” (P.8-
the engine starts. If the engine starts, but
22).)
fails to run, repeat the above procedure.
. If the engine is very hard to start in
extremely cold weather or when restart-
ing, depress the accelerator pedal a little
(approximately 1/3 to the floor) and hold
it and then crank the engine. Release the
accelerator pedal when the engine starts.
position to start cranking the engine. time may make the vehicle more difficult to CONTINUOUSLY VARIABLE TRANS-
After 5 or 6 seconds, stop cranking by start. MISSION (CVT)
pushing the ignition switch to OFF. After When racing the engine up to 4,000 rpm or The Continuously Variable Transmission (CVT)
cranking the engine, release the accel- more under no load condition, the engine in your vehicle is electronically controlled to
erator pedal. Crank the engine with your will enter the fuel cut mode. produce maximum power and smooth operation.
foot off the accelerator pedal by
5. To stop the engine, move the shift lever to The recommended operating procedures for this
depressing the brake pedal and pushing
the P (Park) position (CVT models) or move transmission are shown on the following pages.
the push-button ignition switch to start
the shift lever to the N (Neutral) position (MT Follow these procedures for maximum vehicle
the engine. If the engine starts, but fails
models), and push the ignition switch to the performance and driving enjoyment.
to run, repeat the above procedure.
OFF position.
Engine power may be automatically re-
NOTE: duced to protect the CVT if the engine
CAUTION Care should be taken to avoid situations speed increases quickly when driving on
that can lead to potential battery discharge slippery roads or while being tested on
Do not operate the starter for more and potential no-start conditions such as: some dynamometers.
than 15 seconds at a time. If the engine 1. Installation or extended use of electro-
does not start, push the ignition switch nic accessories that consume battery Starting the vehicle
to OFF and wait 10 seconds before power when the engine is not running 1. After starting the engine, fully depress the
cranking again, otherwise the starter (Phone chargers, GPS, DVD players, foot brake pedal before moving the shift
could be damaged. etc.) lever out of the P (Park) position.
2. Vehicle is not driven regularly and/or This CVT is designed so that the foot
4. Warm-up brake pedal must be depressed before
only driven short distances.
Allow the engine to idle for at least 30 shifting from P (Park) to any driving
seconds after starting. Do not race the In these cases, the battery may need to be position while the ignition switch is in
engine while warming it up. Drive at charged to maintain battery health. the ON position.
moderate speed for a short distance first, The shift lever cannot be moved out of
especially in cold weather. In cold weather, the P (Park) position and into any of
keep the engine running for a minimum of 2 - the other positions if the ignition
3 minutes before shutting it off. Starting and switch is placed in the LOCK, OFF or
stopping the engine over a short period of ACC position or if the key is removed.
Starting and driving 5-17
2. Keep the foot brake pedal depressed, push
the shift lever button and move the shift lever CAUTION
to a driving position.
3. Release the parking brake and foot brake . Except in an emergency, do not shift
pedal, and then gradually start the vehicle in to the N (Neutral) position while
motion. driving. Coasting with the transmis-
sion in the N (Neutral) position may
cause serious damage to the trans-
WARNING mission.
. When stopping the vehicle on an
. Do not depress the accelerator
uphill grade, do not hold the vehicle
pedal while shifting from P (Park)
by depressing the accelerator pedal.
or N (Neutral) to R (Reverse) or D
The foot brake should be used for
(Drive). Always depress the brake SSD1140
this purpose.
pedal until shifting is completed.
Failure to do so could cause you to . Do not downshift abruptly on slip- To move the shift lever,
lose control and have an accident. pery roads. This may cause a loss of
:
*
Push the button A while depressing the
control. brake pedal.
. Cold engine idle speed is high, so
use caution when shifting into a : *
Push the button A .
: Just move the shift lever.
forward or reverse gear before the
engine has warmed up. Shifting
. Never shift to P (Park) or R (Re- After starting the engine, fully depress the brake
verse) while vehicle is moving. Fail- pedal, push the shift lever button and move the
ure to do so could cause you to lose shift lever from the P (Park) position to any of the
control and have an accident. desired shift positions.
SSD1144 SSD1145
Example
Three drive modes (NORMAL, SPORT and NORMAL drive mode
ECO) can be selected depending on the driving The NORMAL drive mode is recommended for
condition. When each mode is selected, the normal driving. To set the NORMAL drive mode,
control state of the engine, CVT (if so press the Drive mode select button and then
equipped), steering and climate appears on press the NORMAL drive mode button. The
the display briefly. control state of the engine, CVT (if so equipped)
Each selected Drive mode (NORMAL, SPORT steering and climate is displayed briefly.
or ECO) is displayed at the top of the display When the NORMAL drive mode is selected, a
screen. voltage meter and an engine torque meter
NOTE: appear on the display screen.
. The display values of torque, boost and NOTE:
current fuel economy may differ de- . The voltage meter may change accord-
pending on driving conditions. Use the ing to the driving condition. This is not
display values as reference only. a malfunction.
SSD1146
SSD1147 SSD1148
screen.
WARNING
. Be sure the parking brake is fully
released before driving. Failure to
do so can cause brake failure and
lead to an accident.
. Do not release the parking brake
from outside the vehicle.
. Do not use the shift lever in place of
the parking brake. When parking, be
sure the parking brake is fully
engaged. SPA2110
. Do not leave children unattended in
a vehicle. They could release the
To apply: Pull the parking brake lever up *
1 .
accelerator pedal. Your vehicle will maintain the of the following methods:
set speed. . Depress the accelerator pedal. When the CAUTION
. To pass another vehicle, depress the vehicle attains the desired speed, push and
accelerator pedal. When you release the release the COAST/SET switch. During the first 1,200 miles (2,000 km),
pedal, the vehicle will return to the previously . Push and hold the ACCEL/RES switch. follow these recommendations to ob-
set speed. When the vehicle attains the desired speed, tain maximum engine performance and
. The vehicle may not maintain the set speed release the switch. ensure the future reliability and econo-
on winding or hilly roads. If this happens, . Push, then quickly release the ACCEL/RES my of your new vehicle. Failure to
drive without the cruise control. switch. Each time you do this, the set speed follow these recommendations may
To cancel the preset speed, use one of the will increase by about 1 MPH (1.6 km/h). result in shortened engine life and
following methods: To reset at a slower cruising speed, use one reduced engine performance.
a) Push the CANCEL switch. of the following methods:
b) Tap the brake pedal. . Avoid driving for long periods at constant
. Lightly tap the brake pedal. When the
c) Turn the MAIN switch off. The CRUISE indicator speed, either fast or slow. Do not run the
vehicle attains the desired speed, push the
light will turn off. engine over 4,000 rpm.
COAST/SET switch and release it.
. If you depress the brake pedal while pushing . Do not accelerate at full throttle in any gear.
. Push and hold the COAST/SET switch.
the ACCEL/RES or COAST/SET switch and Release the switch when the vehicle slows . Avoid quick starts.
reset at the cruising speed, the cruise down to the desired speed. . Avoid hard braking as much as possible.
control will disengage. Turn the MAIN switch
. Push, then quickly release the COAST/SET
off once and then turn it on again.
switch. Each time you do this, the set speed
. The cruise control will automatically cancel if will decrease by about 1 MPH (1.6 km/h).
the vehicle slows more than 8 MPH (13
To resume the preset speed, push and
km/h) below the set speed.
release the ACCEL/RES switch. The vehicle
. If you move the shift lever to the N (Neutral) will resume the last set cruising speed when the
position (Continuously Variable Transmis- vehicle speed is over 25 MPH (40 km/h).
sion models) or depressing the clutch pedal
(Manual Transmission models), the cruise
control will be canceled.
To reset at a faster cruising speed, use one
Starting and driving 5-31
FUEL EFFICIENT DRIVING TIPS
Follow these easy-to-use Fuel Efficient Driving . Recirculating the cool air in the cabin fuel and reduces emissions.
Tips to help you achieve the most fuel economy when the A/C is on reduces cooling load.
8. Buy an automated pass for toll roads.
from your vehicle. 4. Drive at economical speeds and distances. . Automated passes permit drivers to use
1. Use smooth accelerator and brake pedal . Observing the speed limit and not ex-
special lanes to maintain cruising speed
application. ceeding 60 MPH (97 km/h) (where through the toll and avoid stopping and
. Avoid rapid starts and stops. legally allowed) can improve fuel effi- starting.
. Use smooth, gentle accelerator and ciency due to reduced aerodynamic
9. Winter warm up.
brake application whenever possible. drag.
. Limit idling time to minimize impact to fuel
. Maintain constant speed while commut- . Maintaining a safe following distance
economy.
ing and coast whenever possible. behind other vehicles reduces unneces-
. Vehicles typically need no more than 30
sary braking.
2. Maintain constant speed. seconds of idling at start-up to effectively
. Safely monitoring traffic to anticipate
. Look ahead to try and anticipate and circulate the engine oil before driving.
changes in speed permits reduced brak-
minimize stops. . Your vehicle will reach its ideal operating
. Synchronizing your speed with traffic
ing and smooth acceleration changes.
. Select a gear range suitable to road
temperature more quickly while driving
lights allows you to reduce your number versus idling.
conditions.
of stops. 10. Keeping your vehicle cool.
. Maintaining a steady speed can minimize 5. Use cruise control.
. Park your vehicle in a covered parking
red light stops and improve fuel effi- . Using cruise control during highway
area or in the shade whenever possible.
ciency. driving helps maintain a steady speed.
. When entering a hot vehicle, opening the
. Cruise control is particularly effective in
3. Use air conditioning (A/C) at higher vehicle windows will help to reduce the inside
speeds. providing fuel savings when driving on
temperature faster, resulting in reduced
. Below 40 MPH (64 km/h), it is more flat terrains.
demand on your A/C system.
efficient to open windows to cool the 6. Plan for the shortest route.
vehicle due to reduced engine load. . Utilize a map or navigation system to
. Above 40 MPH (64 km/h), it is more determine the best route to save time.
efficient to use A/C to cool the vehicle 7. Avoid idling.
due to increased aerodynamic drag. . Shutting off your engine when safe for
stops exceeding 30-60 seconds saves
CAUTION
. If the warning light illuminates while
driving, AWD mode will be changed
to 2WD mode. Reduce the vehicle
speed and have your vehicle
checked by a NISSAN dealer as
soon as possible. Be especially
careful when driving.
5-36 Starting and driving
PARKING/PARKING ON HILLS
SSD0488
3. To help prevent the vehicle from rolling into
the street when parked on a sloping drive
way, it is a good practice to turn the wheels
dents. as illustrated.
WARNING . Safe parking procedures require . HEADED DOWNHILL WITH CURB: * 1
that both the parking brake be Turn the wheels into the curb and move
. Do not stop or park the vehicle over
applied and the transmission placed the vehicle forward until the curb side
flammable materials such as dry wheel gently touches the curb.
into P (Park) for Continuously Vari-
grass, waste paper or rags. They
able Transmission (CVT) model or in . HEADED UPHILL WITH CURB: * 2
may ignite and cause a fire.
an appropriate gear for Manual Turn the wheels away from the curb and
. Never leave the engine running Transmission (MT) model. Failure move the vehicle back until the curb side
while the vehicle is unattended. to do so could cause the vehicle to wheel gently touches the curb.
. Do not leave children unattended move unexpectedly or roll away and . HEADED UPHILL OR DOWNHILL, NO
inside the vehicle. They could un- result in an accident. CURB: * 3
knowingly activate switches or con- . Make sure the continuously variable Turn the wheels toward the side of the
trols. Unattended children could transmission shift lever has been road so the vehicle will move away from
become involved in serious acci- pushed as far forward as it can go the center of the road if it moves.
4. Models with Intelligent Key system: wheel operations that could cause the electric
Place the ignition switch in the OFF position. WARNING power steering system to overheat.
Models without Intelligent Key system: You may hear a sound when the steering wheel
. If the engine is not running or is is operated quickly. However, this is not a
Place the ignition switch in the LOCK turned off while driving, the power malfunction.
position and remove the key. assist for the steering will not work. If the electric power steering warning light
Steering will be harder to operate. illuminates while the engine is running, it may
. When the electric power steering indicate the electric power steering system is
warning light illuminates with the not functioning properly and may need servicing.
engine running, the power assist for Have the electric power steering system
the steering will cease operation. checked by a NISSAN dealer. (See “Electric
You will still have control of the power steering warning light” (P.2-14).)
vehicle but the steering will be When the electric power steering warning light
harder to operate. illuminates with the engine running, the power
assist for the steering will cease operation. You
The electric power steering system is designed will still have control of the vehicle. However,
to provide power assist while driving to operate greater steering effort is needed, especially in
the steering wheel with light force. sharp turns and at low speeds.
When the steering wheel is operated repeatedly
or continuously while parking or driving at a very
low speed, the power assist for the steering
wheel will be reduced. This is to prevent
overheating of the electric power steering
system and protect it from getting damaged.
While the power assist is reduced, steering
wheel operation will become heavy. When the
temperature of the electric power steering
system goes down, the power assist level will
return to normal. Avoid repeating such steering
BRAKING PRECAUTIONS slope or long grade. Overheated brakes may Parking brake break-in
The brake system has two separate hydraulic reduce braking performance and could result in Break in the parking brake shoes whenever the
circuits. If one circuit malfunctions, you will still loss of vehicle control. stopping effect of the parking brake is weakened
have braking at two wheels. or whenever the parking brake shoes and/or
You may feel a small click and hear a sound WARNING drums/rotors are replaced, in order to assure the
when the brake pedal is fully depressed slowly. best braking performance.
This is not a malfunction and indicates that the . While driving on a slippery surface, This procedure is described in the vehicle
brake assist mechanism is operating properly. be careful when braking, accelerat- service manual and can be performed by a
ing or downshifting. Abrupt braking NISSAN dealer.
Vacuum assisted brakes
or accelerating could cause the
The brake booster aids braking by using engine wheels to skid and result in an
vacuum. If the engine stops, you can stop the accident.
vehicle by depressing the brake pedal. However,
greater foot pressure on the brake pedal will be . If the engine is not running or is
required to stop the vehicle and the stopping turned off while driving, the power
distance will be longer. assist for the brakes will not work.
Braking will be harder.
When the brake pedal is depressed slowly and
firmly, you may hear a clicking noise and feel a
slight pulsation. This is normal and indicates that Wet brakes
the Brake Assist System is operating. When the vehicle is washed or driven through
water, the brakes may get wet. As a result, your
Using the brakes braking distance will be longer and the vehicle
Avoid resting your foot on the brake pedal while may pull to one side during braking.
driving. This will cause overheating of the To dry brakes, drive the vehicle at a safe speed
brakes, wearing out the brake pads and shoes while lightly tapping the brake pedal to heat-up
faster and reduce gas mileage. the brakes. Do this until the brakes return to
To help reduce brake wear and to prevent the normal. Avoid driving the vehicle at high speeds
brakes from overheating, reduce speed and until the brakes function correctly.
downshift to a lower gear before going down a
BRAKE ASSIST surfaces even with ABS. Stopping wheel and varies the brake fluid pressure to
When the force applied to the brake pedal distances may also be longer on prevent each wheel from locking and sliding. By
exceeds a certain level, the Brake Assist is rough, gravel or snow covered preventing each wheel from locking, the system
activated generating greater braking force than a roads, or if you are using tire chains. helps the driver maintain steering control and
conventional brake booster even with light pedal Always maintain a safe distance helps to minimize swerving and spinning on
force. from the vehicle in front of you. slippery surfaces.
Ultimately, the driver is responsible Using the system
for safety.
WARNING Depress the brake pedal and hold it down.
. Tire type and condition may also Depress the brake pedal with firm steady
The Brake Assist is only an aid to assist affect braking effectiveness. pressure, but do not pump the brakes. The
braking operation and is not a collision — When replacing tires, install the ABS will operate to prevent the wheels from
warning or avoidance device. It is the specified size of tires on all four locking up. Steer the vehicle to avoid obstacles.
driver’s responsibility to stay alert, drive wheels.
safely and be in control of the vehicle at
all times.
— When installing a spare tire, WARNING
make sure that it is the proper
size and type as specified on the Do not pump the brake pedal. Doing so
ANTI-LOCK BRAKING SYSTEM (ABS) Tire and Loading Information may result in increased stopping dis-
label. See “Tire and Loading tances.
WARNING Information label” (P.9-11) of
this manual.
Self-test feature
. The Anti-lock Braking System (ABS) — For detailed information, see
is a sophisticated device, but it The ABS includes electronic sensors, electric
“Wheels and tires” (P.8-30) of
cannot prevent accidents resulting pumps, hydraulic solenoids and a computer. The
this manual.
from careless or dangerous driving computer has a built-in diagnostic feature that
techniques. It can help maintain tests the system each time you start the engine
The Anti-lock Braking System (ABS) controls and move the vehicle at a low speed in forward
vehicle control during braking on the brakes so the wheels do not lock during hard
slippery surfaces. Remember that or reverse. When the self-test occurs, you may
braking or when braking on slippery surfaces. hear a “clunk” noise and/or feel a pulsation in the
stopping distances on slippery sur- The system detects the rotation speed at each
faces will be longer than on normal brake pedal. This is normal and does not
5-40 Starting and driving
VEHICLE DYNAMIC CONTROL (VDC)
SYSTEM
indicate a malfunction. If the computer senses a The Vehicle Dynamic Control (VDC) system keep the vehicle on the steered path.
malfunction, it switches the ABS off and uses various sensors to monitor driver inputs . You may feel a pulsation in the brake pedal
illuminates the ABS warning light on the and vehicle motion. Under certain driving con- and hear a noise or vibration from under the
instrument panel. The brake system then oper- ditions, the VDC system helps to perform the hood. This is normal and indicates that the
ates normally, but without anti-lock assistance. following functions. VDC system is working properly.
If the ABS warning light illuminates during the . Controls brake pressure to reduce wheel . Adjust your speed and driving to the road
self-test or while driving, have the vehicle slip on one slipping drive wheel so power is conditions.
checked by a NISSAN dealer. transferred to a non slipping drive wheel on If a malfunction occurs in the system, the VDC
the same axle. warning light illuminates in the instrument
Normal operation . Controls brake pressure and engine output panel. The VDC system automatically turns off.
The ABS operates at speeds above 3 to 6 MPH to reduce drive wheel slip based on vehicle The VDC OFF switch is used to turn off the VDC
(5 to 10 km/h). The speed varies according to speed (traction control function). system. The VDC off indicator illuminates to
road conditions. . Controls brake pressure at individual wheels indicate the VDC system is off. When the VDC
When the ABS senses that one or more wheels and engine output to help the driver maintain switch is used to turn off the system, the VDC
are close to locking up, the actuator rapidly control of the vehicle in the following system still operates to prevent one drive wheel
applies and releases hydraulic pressure. This conditions: from slipping by transferring power to a non
action is similar to pumping the brakes very — understeer (vehicle tends to not follow slipping drive wheel. The VDC warning light
quickly. You may feel a pulsation in the brake the steered path despite increased flashes if this occurs. All other VDC functions
pedal and hear a noise from under the hood or steering input) are off, and the VDC warning light will not
feel a vibration from the actuator when it is — oversteer (vehicle tends to spin due to flash. The VDC system is automatically reset to
operating. This is normal and indicates that the certain road or driving conditions). on when the ignition switch is placed in the off
ABS is operating properly. However, the pulsa- position then back to the on position.
The VDC system can help the driver to maintain
tion may indicate that road conditions are
control of the vehicle, but it cannot prevent loss See “Vehicle Dynamic Control (VDC) warning
hazardous and extra care is required while
of vehicle control in all driving situations. light” (P.2-17) and “Vehicle Dynamic Control
driving.
When the VDC system operates, the VDC (VDC) off indicator light” (P.2-19).
warning light in the instrument panel flashes The computer has a built-in diagnostic feature
so note the following: that tests the system each time you start the
. The road may be slippery or the system may engine and move the vehicle forward or in
determine some action is required to help reverse at a slow speed. When the self-test
Starting and driving 5-41
occurs, you may hear a “clunk” noise and/or feel . If brake related parts such as brake . The VDC system is not a substitute
a pulsation in the brake pedal. This is normal and pads, rotors and calipers are not for winter tires or tire chains on a
is not an indication of a malfunction. NISSAN recommended or are extre- snow covered road.
mely deteriorated, the VDC system
WARNING may not operate properly and the
VDC warning light may illumi-
. The VDC system is designed to help nate.
improve driving stability but does . If engine control related parts are
not prevent accidents due to abrupt not NISSAN recommended or are
steering operation at high speeds or extremely deteriorated, the VDC
by careless or dangerous driving warning light may illuminate.
techniques. Reduce vehicle speed . When driving on extremely inclined
and be especially careful when driv- surfaces such as higher banked
ing and cornering on slippery sur- corners, the VDC system may not
faces and always drive carefully. operate properly and the VDC warn-
. Do not modify the vehicle’s suspen- ing light may illuminate. Do not
sion. If suspension parts such as drive on these types of roads.
shock absorbers, struts, springs, . When driving on an unstable sur-
stabilizer bars, bushings and face such as a turntable, ferry,
wheels are not NISSAN recom- elevator or ramp, the VDC warning
mended for your vehicle or are light may illuminate. This is not
extremely deteriorated, the VDC a malfunction. Restart the engine
system may not operate properly. after driving onto a stable surface.
This could adversely affect vehicle
. If wheels or tires other than the
handling performance, and the VDC
NISSAN recommended ones are
warning light may illuminate.
used, the VDC system may not
operate properly and the VDC warn-
ing light may illuminate.
Hazard warning flasher switch .............................................. 6-2 Jump starting ............................................................................. 6-8
Emergency engine shut off (models with Intelligent Push starting ........................................................................... 6-10
Key system) ................................................................................ 6-2 If your vehicle overheats ...................................................... 6-10
Flat tire ......................................................................................... 6-3 Towing your vehicle .............................................................. 6-12
Tire Pressure Monitoring System (TPMS) .................... 6-3 Towing recommended by NISSAN ........................... 6-13
Changing a flat tire ............................................................. 6-3 Vehicle recovery (freeing a stuck vehicle) ............... 6-14
HAZARD WARNING FLASHER EMERGENCY ENGINE SHUT OFF
SWITCH (models with Intelligent Key system)
To shut off the engine in an emergency situation
to other traffic.
while driving, perform the following procedure:
. Turn signals do not work when the
. Rapidly push the push-button ignition switch
hazard warning flasher lights are
3 consecutive times in less than 1.5
on.
seconds, or
The flasher can be actuated with the ignition . Push and hold the push-button ignition
switch in any position. switch for more than 2 seconds.
Some state laws may prohibit the use of
the hazard warning flasher switch while
driving.
SIC2574
WARNING
. If stopping for an emergency, be
sure to move the vehicle well off the
road.
. Do not use the hazard warning
flashers while moving on the high-
way unless unusual circumstances
force you to drive so slowly that
your vehicle might become a hazard
TIRE PRESSURE MONITORING SYS- failure. Serious vehicle damage the tire pressure sensors.
TEM (TPMS) could occur and may lead to an
This vehicle is equipped with the Tire Pressure accident and could result in serious CHANGING A FLAT TIRE
Monitoring System (TPMS). It monitors tire personal injury. Check the tire pres- If you have a flat tire, follow the instructions
pressure of all tires except the spare. When sure for all four tires. Adjust the tire below.
the low tire pressure warning light is lit, and the pressure to the recommended COLD
CHECK TIRE PRES (pressure) warning mes- tire pressure shown on the Tire and Stopping the vehicle
sage is displayed in the vehicle information Loading Information label to turn 1. Safely move the vehicle off the road and
display, one or more of your tires is significantly the low tire pressure warning light away from traffic.
under-inflated. If the vehicle is being driven with OFF. If you have a flat tire, replace it
2. Turn on the hazard warning flashers.
low tire pressure, the TPMS will activate and with a spare tire as soon as possi-
warn you of it by the low tire pressure warning ble. 3. Park on a level surface and apply the parking
light. This system will activate only when the brake.
. When a spare tire is mounted or a
vehicle is driven at speeds above 16 MPH (25 wheel is replaced, the TPMS will not 4. Continuously Variable Transmission
km/h). For more details, see “Warning/indicator function and the low tire pressure (CVT) models:
lights and audible reminders” (P.2-12) and “Tire warning light will flash for approxi- Move the shift lever to the P (Park) position.
Pressure Monitoring System (TPMS)” (P.5-4). mately 1 minute. The light will Manual Transmission (MT) models:
remain on after 1 minute. Contact
your NISSAN dealer as soon as Move the shift lever to the R (Reverse)
WARNING position.
possible for tire replacement and/
. If the low tire pressure warning light or system resetting. 5. Turn off the engine.
illuminates while driving, avoid sud- . Replacing tires with those not ori- 6. Raise the hood to warn other traffic, and to
den steering maneuvers or abrupt ginally specified by NISSAN could signal professional road assistance person-
braking, reduce vehicle speed, pull affect the proper operation of the nel that you need assistance.
off the road to a safe location and TPMS. 7. Have all passengers get out of the vehicle
stop the vehicle as soon as possi- . Do not inject any tire liquid or and stand in a safe place, away from traffic
ble. Driving with under-inflated tires aerosol tire sealant into the tires, and clear of the vehicle.
may permanently damage the tires as this may cause a malfunction of
and increase the likelihood of tire
SCE0946
WARNING Jacking tools
Be sure to block the wheel as the Getting the spare tire and tools
vehicle may move and result in personal Open the lift gate. Raise the cargo floor board
injury. *1 . Remove jacking tools.
WARNING
. Never get under the vehicle while it
is supported only by the jack. If it is
necessary to work under the vehicle,
support it with safety stands.
. Use only the jack provided with your
vehicle to lift the vehicle. Do not use
the jack provided with your vehicle
on other vehicles. The jack is de-
signed for lifting only your vehicle
during a tire change.
. Use the correct jack-up points.
Never use any other part of the
vehicle for jack support.
. Never jack up the vehicle more than
necessary.
SCE0947
. Never use blocks on or under the
The spare tire is located under the cargo floor jack.
board. . Do not start or run the engine while
Loosen the clamp * 2 and remove the spacer vehicle is on the jack, as it may
*1 and take out the spare tire. cause the vehicle to move.
. Do not allow passengers to stay in
the vehicle while it is on the jack.
CAUTION
SCE0981 . Always connect positive (+) to posi-
2. Apply the parking brake. tive (+) and negative (−) to body
ground (for example, as illustrated),
WARNING 3. Continuously Variable Transmission not to the battery.
(CVT) models:
. Make sure the jumper cables do not
Always follow the instructions below. Move the shift lever to the P (Park) position. touch moving parts in the engine
Failure to do so could result in damage
Manual Transmission (MT) models: compartment and that the cable
to the charging system and cause
Move the shift lever to the N (Neutral) clamps do not contact any other
personal injury.
position. metal.
1. If the booster battery is in another vehicle 4. Switch off all unnecessary electrical systems
* B , position the two vehicles (* A and * B ) (headlights, heater, air conditioner, etc.). 7. Start the engine of the booster vehicle *
B
and let it run for a few minutes.
to bring their batteries into close proximity to 5. Remove the vent caps on the battery (if so
each other. equipped). Cover the battery with a firmly 8. Keep the engine speed of the booster
wrung out moist cloth to reduce explosion vehicle *B at about 2,000 rpm, and start
Do not allow the two vehicles to touch.
hazard. the engine of the vehicle *
A being jump
started.
When towing your vehicle, all State (Provincial in . Always attach safety chains before
Canada) and local regulations for towing must towing.
be followed. Incorrect towing equipment could
damage your vehicle. Towing instructions are For information about towing your vehicle behind
available from a NISSAN dealer. Local service a recreational vehicle (RV), see “Flat towing”
operators are familiar with the applicable laws (P.9-17) of this manual.
and procedures for towing. To assure proper
towing and to prevent accidental damage to
your vehicle, NISSAN recommends that you
have a service operator tow your vehicle. It is
advisable to have the service operator carefully
read the following precautions.
WARNING
. Never ride in a vehicle that is being
towed.
. Never get under your vehicle after it
has been lifted by a tow truck.
CAUTION
. When towing, make sure that the
transmission, axles, steering system
and powertrain are in working con-
dition. If any unit is damaged, dol-
lies must be used.
SCE0950
Two-wheel drive models
TOWING RECOMMENDED BY
ious and expensive damage to the
NISSAN transmission. If it is necessary to
Two-Wheel Drive (2WD) models tow the vehicle with the rear wheels
NISSAN recommends that your vehicle be raised, always use towing dollies
towed with the driving (front) wheels off the under the front wheels.
ground or place the vehicle on a flat bed truck as . When towing CVT models with the
illustrated. front wheels on towing dollies:
Push the ignition switch to the
ACC or ON position, and secure
CAUTION the steering wheel in a straight-
ahead position with a rope or simi-
. Never tow CVT models with the front lar device. Move the shift lever to
wheels on the ground or four the N (Neutral) position.
wheels on the ground (forward or
backward), as this may cause ser-
In case of emergency 6-13
VEHICLE RECOVERY (freeing a stuck
vehicle)
WARNING
. Stand clear of a stuck vehicle.
. Do not spin your tires at high speed.
This could cause them to explode
and result in serious injury. Parts of
your vehicle could also overheat
and be damaged.
SCE0952
Pulling a stuck vehicle
All-wheel drive models
All-Wheel Drive (AWD) models Do not use the tie down hook for towing or
vehicle recovery.
NISSAN recommends that towing dollies be
used when towing your vehicle or the vehicle be
placed on a flat bed truck as illustrated.
CAUTION
Never tow AWD models with any of the
wheels on the ground as this may cause
serious and expensive damage to the
powertrain.
In order to maintain the appearance of your WASHING . Avoid using tight-napped or rough
vehicle, it is important to take proper care of it. Wash dirt off the vehicle with a wet sponge and cloths, such as washing mitts. Care
To protect the paint surfaces, wash your vehicle plenty of water. Clean the vehicle thoroughly must be taken when removing
as soon as you can: using a mild soap, a special vehicle soap or caked-on dirt or other foreign sub-
. after a rainfall to prevent possible damage general purpose dishwashing liquid mixed with stances so the paint surface is not
from acid rain clean, lukewarm (never hot) water. scratched or damaged.
. after driving on coastal roads
Rinse the vehicle thoroughly with plenty of clean
. when contaminants such as soot, bird CAUTION water.
droppings, tree sap, metal particles or bugs
get on the paint surface . Do not use car washes that use acid Inside flanges, seams and folds on the doors,
hatches and hood are particularly vulnerable to
. when dust or mud builds up on the surface in the detergent. Some car washes,
especially brushless ones, use some the effects of road salt. Therefore, these areas
Whenever possible, store or park your vehicle must be regularly cleaned. Make sure that the
inside a garage or in a covered area. acid for cleaning. The acid may react
with some plastic vehicle compo- drain holes in the lower edge of the door are
When it is necessary to park outside, park in a open. Spray water under the body and in the
nents, causing them to crack. This
shady area or protect the vehicle with a body wheel wells to loosen the dirt and wash away
could affect their appearance, and
cover. road salt.
also could cause them not to func-
Be careful not to scratch the paint surface tion properly. Always check with Avoid leaving water spots on the paint surface
when putting on or removing the body your car wash to confirm that acid by using a damp chamois to dry the vehicle.
cover. is not used.
. Do not wash the vehicle with strong
household soap, strong chemical
detergents, gasoline or solvents.
. Do not wash the vehicle in direct
sunlight or while the vehicle body is
hot, as the surface may become
water-spotted.
WARNING
To avoid potential pedal interference
that may result in a collision or injury:
. NEVER place a floor mat on top of
another floor mat in the driver front
position.
. Use only genuine NISSAN floor
mats specifically designed for use
in your vehicle model. See your
SAI0050 SAI0055
NISSAN dealer for more informa-
Front (example) Bracket positions
tion.
Floor mat positioning aid The illustration shows the location of the floor
. Properly position the mats in the
mat brackets.
floorwell using the floor mat posi- This model includes front floor mat brackets to
tioning aid. See “Floor mat posi- act as floor mat positioning aid. NISSAN floor SEAT BELTS
tioning aid” (P.7-6). mats have been specially designed for your The seat belts can be cleaned by wiping them
vehicle model. The front floor mats have with a sponge dampened in a mild soap
The use of genuine NISSAN floor mats can grommet holes in them. To install, simply solution. Allow the belts to dry completely in
extend the life of your vehicle carpet and make it position the mat by placing the floor mat bracket the shade before using them.
easier to clean the interior. Mats should be through the floor mat grommet hole while See “Seat belts” (P.1-10).
maintained with regular cleaning and replaced if centering the mat in the floorwell.
they become excessively worn. Periodically check to make certain that the mats
are properly positioned. WARNING
Do not allow wet seat belts to roll up in
the retractor. NEVER use bleach, dye, or
chemical solvents to clean the seat
7-6 Appearance and care
CORROSION PROTECTION
belts, since these materials may se- MOST COMMON FACTORS CONTRI- Temperature
verely weaken the seat belt webbing. BUTING TO VEHICLE CORROSION A temperature increase will accelerate the rate
. The accumulation of moisture-retaining dirt of corrosion to those parts which are not well
and debris in body panel sections, cavities, ventilated.
and other areas.
. Damage to paint and other protective coat-
Air pollution
ings caused by gravel and stone chips or Industrial pollution, the presence of salt in the air
minor traffic accidents. in coastal areas, or heavy road salt use will
accelerate the corrosion process. Road salt will
ENVIRONMENTAL FACTORS INFLU-
also accelerate the disintegration of paint
ENCE THE RATE OF CORROSION
surfaces.
Moisture TO PROTECT YOUR VEHICLE FROM
Accumulation of sand, dirt and water on the CORROSION
vehicle body underside can accelerate corro- . Wash and wax your vehicle often to keep the
sion. Wet floor coverings will not dry completely vehicle clean.
inside the vehicle, and should be removed for
. Always check for minor damage to the paint
drying to avoid floor panel corrosion.
and repair it as soon as possible.
Relative humidity . Keep drain holes at the bottom of the doors
Corrosion will be accelerated in areas of high open to avoid water accumulation.
relative humidity, especially those areas where . Check the underbody for accumulation of
the temperatures stay above freezing where sand, dirt or salt. If present, wash with water
atmospheric pollution exists, or where road salt as soon as possible.
is used.
CAUTION
. NEVER remove dirt, sand or other
debris from the passenger compart-
ment by washing it out with a hose.
Some day-to-day and regular maintenance is These checks or inspections can be done by During the normal day-to-day operation of the
essential to maintain your vehicle good mechan- yourself, a qualified technician or, if you prefer, a vehicle, general maintenance should be per-
ical condition, as well as its emission and engine NISSAN dealer. formed regularly as prescribed in this section. If
performance. you detect any unusual sounds, vibrations or
WHERE TO GO FOR SERVICE
smell, be sure to check for the cause or have a
It is the owner’s responsibility to make sure that If maintenance service is required or your vehicle NISSAN dealer do it promptly. In addition, you
the scheduled maintenance, as well as general appears to malfunction, have the systems should notify a NISSAN dealer if you think that
maintenance, is performed. checked and serviced by a NISSAN dealer. repairs are required.
As the vehicle owner, you are the only one who NISSAN technicians are well-trained specialists When performing any checks or maintenance
can ensure that your vehicle receives the proper and are kept up-to-date with the latest service work, see “Maintenance precautions” (P.8-5).
maintenance care. You are a vital link in the information through technical bulletins, service
maintenance chain. tips, and in-dealership information systems. EXPLANATION OF MAINTENANCE
SCHEDULED MAINTENANCE They are completely qualified to work on ITEMS
NISSAN vehicles before work begins. Additional information on the following
For your convenience, both required and op-
You can be confident that a NISSAN dealer’s items with “*” is found later in this section.
tional scheduled maintenance items are de-
scribed and listed in your “NISSAN Service and service department performs the best job to Outside the vehicle
Maintenance Guide”. You must refer to that meet the maintenance requirements on your
The maintenance items listed here should be
guide to ensure that necessary maintenance is vehicle.
performed from time to time, unless otherwise
performed on your vehicle at regular intervals. specified.
GENERAL MAINTENANCE Doors and engine hood: Check that all doors
General maintenance includes those items and the engine hood operate properly. Also
which should be checked during normal day- ensure that all latches lock securely. Lubricate
to-day operation. They are essential for proper hinges, latches, latch pins, rollers and links if
vehicle operation. It is your responsibility to necessary. Make sure that the secondary latch
perform these procedures regularly as pre- keeps the hood from opening when the primary
scribed. latch is released.
Performing general maintenance checks re- When driving in areas using road salt or other
quires minimal mechanical skill and only a few corrosive materials, check lubrication frequently.
general automotive tools. Lights*: Clean the headlights on a regular basis.
8-2 Maintenance and do-it-yourself
Make sure that the headlights, stop lights, tail For additional information regarding tires, refer Continuously Variable Transmission (CVT)
lights, turn signal lights, and other lights are all to “Important Tire Safety Information” (US) or P (Park) position mechanism: On a fairly
operating properly and installed securely. Also “Tire Safety Information” (Canada) in the War- steep hill, check that the vehicle is held securely
check headlight aim. ranty Information Booklet. with the shift lever in the P (Park) position
Road wheel nuts (lug nuts)*: When checking Windshield: Clean the windshield on a regular without applying any brakes.
the tires, make sure no wheel nuts are missing, basis. Check the windshield at least every six Parking brake: Check the parking brake
and check for any loose wheel nuts. Tighten if months for cracks or other damage. Have a operation regularly. The vehicle should be
necessary. damaged windshield repaired by a qualified securely held on a fairly steep hill with only the
Tire rotation*: Tires should be rotated every repair facility. parking brake applied. If the parking brake needs
5,000 miles (8,000 km). Windshield wiper blades*: Check for cracks adjusted, see a NISSAN dealer.
Tires*: Check the pressure with a gauge often or wear if they do not wipe properly. Seat belts: Check that all parts of the seat belt
and always prior to long distance trips. If system (for example, buckles, anchors, adjusters
Inside the vehicle and retractors) operate properly and smoothly,
necessary, adjust the pressure in all tires,
The maintenance items listed here should be and are installed securely. Check the belt
including the spare, to the pressure specified.
checked on a regular basis, such as when webbing for cuts, fraying, wear or damage.
Check carefully for damage, cuts or excessive
performing scheduled maintenance, cleaning
wear. Seats: Check seat position controls such as
the vehicle, etc.
Tire Pressure Monitoring System (TPMS) seat adjusters, seatback recliners, etc. to ensure
Accelerator pedal: Check the pedal for they operate smoothly and that all latches lock
transmitter components: Replace the TPMS
smooth operation and make sure the pedal securely in every position. Check that the head
transmitter grommet seal, valve core and cap
does not catch or require uneven effort. Keep restraints move up and down smoothly and that
when the tires are replaced due to wear or age.
the floor mat away from the pedal. the locks (if so equipped) hold securely in all
Wheel alignment and balance: If the vehicle
Brake pedal: Check the pedal for smooth latched positions.
should pull to either side while driving on a
operation. If the brake pedal suddenly goes Steering wheel: Check for changes in the
straight and level road, or if you detect uneven or
down further than normal, the pedal feels steering conditions, such as excessive free play,
abnormal tire wear, there may be a need for
spongy or the vehicle seems to take longer to hard steering or strange noises.
wheel alignment.
stop, see a NISSAN dealer immediately. Keep
If the steering wheel or seat vibrates at normal Warning lights and chimes: Make sure that
the floor mat away from the pedal.
highway speeds, wheel balancing may be all warning lights and chimes are operating
Brakes: Check that the brakes do not pull the properly.
needed.
vehicle to one side when applied.
Windshield defroster: Check that the air
Maintenance and do-it-yourself 8-3
comes out of the defroster outlets properly and charged to maintain battery health. etc., that may have accumulated. Make sure the
in sufficient quantity when operating the heater Brake and clutch fluid level*: Make sure that hoses have no cracks, deformation, rot or loose
or air conditioner. the brake and clutch fluid level is between the connections.
Windshield wiper and washer*: Check that MAX and MIN lines on the reservoir. Underbody: The underbody is frequently ex-
the wipers and washers operate properly and Engine coolant level*: Check the coolant level posed to corrosive substances such as those
that the wipers do not streak. when the engine is cold. used on icy roads or to control dust. It is very
important to remove these substances, other-
Under the hood and vehicle Engine drive belt*: Make sure that the drive
wise rust will form on the floor pan, frame, fuel
The maintenance items listed here should be belt is not frayed, worn, cracked or oily.
lines and around the exhaust system. At the end
checked periodically (for example, each time you Engine oil level*: Check the level after parking of winter, the underbody should be thoroughly
check the engine oil or refuel). the vehicle on a level surface and turning off the flushed with plain water, being careful to clean
Battery*: Check the fluid level in each cell. engine. Wait more than 10 minutes for the oil to those areas where mud and dirt may accumu-
drain back into the oil pan. late. For additional information, see “Cleaning
It should be between the MAX and MIN lines.
Exhaust system: Make sure there are no loose exterior” (P.7-2).
Vehicles operated in high temperatures or under
severe condition require frequent checks of the supports, cracks or holes. If the sound of the Windshield washer fluid*: Check that there is
battery fluid level. exhaust seems unusual or there is a smell of adequate fluid in the reservoir.
exhaust fumes, immediately have the exhaust
NOTE:
system inspected by a NISSAN dealer. (See
Care should be taken to avoid situations “Precautions when starting and driving” (P.5-3)
that can lead to potential battery discharge for exhaust gas (carbon monoxide).)
and potential no-start conditions such as:
Fluid leaks: Check under the vehicle for fuel,
1. Installation or extended use of electro-
oil, water or other fluid leaks after the vehicle has
nic accessories that consume battery
been parked for a while. Water dripping from the
power when the engine is not running
air conditioner after use is normal. If you should
(Phone chargers, GPS, DVD players,
notice any leaks or if gasoline fumes are evident,
etc.)
check for the cause and have it corrected
2. Vehicle is not driven regularly and/or immediately.
only driven short distances.
Radiator and hoses: Check the front of the
In these cases, the battery may need to be radiator and clean off any dirt, insects, leaves,
SDI2639
The engine cooling system is filled at the factory cooling fan is operating, be sure low the coolant manufacture’s
with a pre-diluted mixture of 50% Genuine that hands or other items do not get instructions to maintain minimum
NISSAN Long Life Antifreeze/Coolant (blue) and caught in it. antifreeze protection to -348F
50% water to provide year-round anti-freeze (-378C). The use of other types of
and coolant protection. The anti-freeze solution coolant solutions other than Genu-
contains rust and corrosion inhibitors. Additional ine NISSAN Long Life Antifreeze/
engine cooling system additives are not neces- CAUTION Coolant (blue) or equivalent may
sary. damage the engine cooling system.
. Never use any cooling system ad-
ditives such as radiator sealer. Ad- . The life expectancy of the factory-fill
WARNING ditives may clog the cooling system coolant is 105,000 miles (168,000
and cause damage to the engine, km) or 7 years. Mixing any other
. Never remove the radiator or cool- transmission and/or cooling sys- type of coolant other than Genuine
ant reservoir cap when the engine is tem. NISSAN Long Life Antifreeze/Cool-
hot. Wait until the engine and ant (blue) , including Genuine
. When adding or replacing coolant,
radiator cool down. Serious burns NISSAN Long Life Antifreeze/Cool-
be sure to use only Genuine
could be caused by high pressure ant (green), or the use of non-
NISSAN Long Life Antifreeze/Cool-
fluid escaping from the radiator. distilled water will reduce the life
ant (blue) or equivalent. Genuine
See precautions in “If your vehicle expectancy of the factory-fill cool-
NISSAN Long Life Antifreeze/Cool-
overheats” (P.6-10) of this manual. ant. Refer to the NISSAN Service
ant (blue) is pre-diluted to provide
and Maintenance Guide for more
. The radiator is equipped with a antifreeze protection to -348F
details.
pressure type radiator cap. To pre- (-378C). If additional freeze protec-
vent engine damage, use only a tion is needed due to weather where
genuine NISSAN radiator cap. you operate your vehicle, add Gen-
. If the engine was stopped soon uine NISSAN Long Life Antifreeze/
when the engine is hot, the cooling Coolant (blue) concentrate follow-
fan may operate for approximately ing the directions on the container.
10 minutes after the engine was If an equivalent coolant other than
stopped to cool the components in Genuine NISSAN Long Life Anti-
the engine compartment. When the freeze/Coolant (blue) is used, fol-
WARNING
. To avoid the danger of being
SDI2641 scalded, never change the coolant SDI1993
when the engine is hot.
CHECKING ENGINE COOLANT LEVEL CHECKING ENGINE OIL LEVEL
Check the coolant level in the reservoir when . Never remove the radiator cap when
the engine is hot. Serious burns 1. Park the vehicle on a level surface and apply
the engine is cold. If the coolant level is below the parking brake.
the MIN level * 2 , open the reservoir cap and
could be caused by high pressure
2. Run the engine until it reaches operating
add coolant up to the MAX level * 1 . If the
fluid escaping from the radiator.
. Avoid direct skin contact with used temperature.
reservoir is empty, check the coolant level in the
radiator when the engine is cold. If there is coolant. If skin contact is made, 3. Turn off the engine. Wait more than 10
insufficient coolant in the radiator, fill the radiator wash thoroughly with soap or hand minutes for the oil to drain back into
with coolant up to the filler opening and also add cleaner as soon as possible. the oil pan.
it to the reservoir up to the MAX level * 1 . . Keep coolant out of reach of chil- 4. Remove the dipstick and wipe it clean.
Tighten the cap securely after adding engine dren and pets. Reinsert it all the way.
coolant. 5. Remove the dipstick again and check the oil
If the cooling system frequently requires Engine coolant must be disposed of properly. level. It should be within the range *
C . If the
coolant, have it checked by a NISSAN Check your local regulations. oil level is below * A , remove the oil filler
dealer. cap and pour recommended oil through the
8-8 Maintenance and do-it-yourself
opening. Do not overfill *
B . 4. Raise and support the vehicle using a
6. Recheck oil level with the dipstick. suitable floor jack and safety jack stands.
. Place the safety jack stands under the
It is normal to add some oil between oil
vehicle jack-up points.
maintenance intervals or during the break-
. A suitable adapter should be attached to
in period, depending on the severity of
operating conditions. the jack stand saddle.
CAUTION CAUTION
Oil level should be checked regularly. Make sure the correct lifting and sup-
Operating the engine with an insuffi- port points are used to avoid vehicle
cient amount of oil can damage the damage.
engine, and such damage is not cov- SDI2652
ered by the warranty.
CAUTION
WARNING
. Use only Genuine NISSAN CVT Fluid
NS-2. Do not mix with other fluids. . Use only new fluid from a sealed
. Using transmission fluid other than container. Old, inferior or contami-
Genuine NISSAN CVT Fluid NS-2 nated fluid may damage the brake
will damage the CVT, which is not and clutch systems. The use of
covered by the NISSAN new vehicle improper fluids can damage the
limited warranty. brake and clutch systems, and affect
the vehicle’s stopping ability.
SDI2655
. Clean the filler cap before removing.
Check the fluid level in the reservoir. If the fluid is
. Brake and clutch fluid is poisonous
below the MIN line * 2 or the brake warning
and should be stored carefully in
light comes on, add Genuine NISSAN Super
marked containers out of the reach
Heavy Duty Brake Fluid or equivalent DOT 3
of children.
fluid up to the MAX line * 1 . If fluid must be
added frequently, the system should be checked
by a NISSAN dealer.
CAUTION
Do not spill the fluid on any painted
surfaces. This will damage the paint. If
fluid is spilled, immediately wash the
surface with water.
CAUTION
. Do not substitute engine anti-freeze
SDI2429
coolant for window washer solution.
This may result in damage to the
To fill the window washer fluid reservoir, lift the paint.
cap and pour the window washer fluid into the . Do not fill the window washer
reservoir opening. reservoir tank with washer fluid
Add a washer solvent to the washer for better concentrates at full strength. Some
cleaning. In the winter season, add a windshield methyl alcohol based washer fluid
washer antifreeze. Follow the manufacturer’s concentrates may permanently stain
instructions for the mixture ratio. the grille if spilled while filling the
Fill the window washer fluid reservoir periodi- window washer reservoir tank.
cally. . Pre-mix washer fluid concentrates
Add fluid when the low washer fluid warning with water to the manufacturer’s
light illuminates (if so equipped). recommended levels before pouring
the fluid into the window washer
To check the fluid level, use your finger to plug reservoir tank. Do not use the
the center hole * 1 of the cap/tube assembly,
window washer reservoir tank to
then remove it from the reservoir. If there is no mix the washer fluid concentrate
8-12 Maintenance and do-it-yourself
BATTERY
2. Vehicle is not driven regularly and/or . Battery posts, terminals and related If it is necessary to add fluid, add only distilled
only driven short distances. accessories contain lead and lead water to bring the level to the indicator in each
compounds. Wash hands after filler opening. Do not overfill.
In these cases, the battery may need to be
charged to maintain battery health. handling.
. Keep the battery out of the reach of
children.
WARNING
. Do not expose the battery to flames
or electrical sparks. Hydrogen gas
generated by the battery is explo-
sive. Do not allow battery fluid to
JUMP STARTING
If jump starting is necessary, see “Jump starting” CAUTION
(P.6-8). If the engine does not start by jump
starting, the battery may have to be replaced. . Do not ground accessories directly
Contact a NISSAN dealer. to the battery terminal. Doing so will
bypass the variable voltage control
system and the vehicle battery may
not charge completely.
. Use electrical accessories with the
engine running to avoid discharging
the vehicle battery.
CAUTION
Be sure to use the correct socket to
remove the spark plugs. An incorrect
SDI1881 socket can damage the spark plugs.
1. Alternator
2. Drive belt auto-tensioner
3. Crankshaft pulley
4. Air conditioner compressor
5. Water pump
WARNING
Be sure the ignition switch is in the OFF
or LOCK position before servicing drive
belts. The engine could rotate unex-
pectedly.
SDI2670 SDI2667
REPLACING SPARK PLUGS To remove the filter, pull the air duct *1 upward
If replacement is required, see a NISSAN dealer to remove it. Pull the tabs * 2 , then pull the
CLEANING
If your windshield is not clear after using the
windshield washer or if a wiper blade chatters
when running, wax or other material may be on
the blade or windshield.
Clean the outside of the windshield with a
washer solution or a mild detergent. Your
windshield is clean if beads do not form when
rinsing with clear water.
Clean each blade by wiping it with a cloth
soaked in a washer solution or a mild detergent.
Then rinse the blade with clear water. If your
windshield is still not clear after cleaning the SDI1803
blades and using the wiper, replace the blades.
REPLACING 4. Rotate the wiper blade so that the dimple is
Replace the wiper blades if they are worn. in the groove.
CAUTION Before replacing the wiper blades, the wiper
Worn windshield wiper blades can
should be in the fully up position to avoid CAUTION
scratching the engine hood or damaging the
damage the windshield and impair
driver vision.
wiper arm. To pull up the wiper arm, see . After wiper blade replacement, re-
“Windshield wiper and washer switch” (P.2-32). turn the wiper arm to its original
1. Lift the wiper arm away from the windshield. position; otherwise it may be da-
2. Push and hold the release tab *A , and
maged when the hood is opened.
move the wiper blade down the wiper arm . Make sure the wiper blades contact
*1 . the glass; otherwise the arm may be
damaged from wind pressure.
3. Insert the new wiper blade onto the wiper
arm until a click sounds.
Contact a NISSAN dealer if checking or If the brakes do not operate properly, have the
replacement is required. brakes checked by a NISSAN dealer.
SELF-ADJUSTING BRAKES
Your vehicle is equipped with self-adjusting
brakes.
The disc-type brakes self-adjust every time the
brake pedal is applied.
WARNING
See a NISSAN dealer for a brake
system check if the brake pedal height
does not return to normal.
light to moderate stops is normal and does not 2. Open the engine hood.
affect the function or performance of the brake 3. Remove the fuse/fusible link holder cover by
system. pushing the tab * 1 and lifting the cover
Proper brake inspection intervals should from the right side *2 , then the left side
be followed. For additional information, see the * 3 .
maintenance log section of your “NISSAN 4. Locate the fuse that needs to be replaced.
Service and Maintenance Guide”.
5. Remove the fuse using the fuse puller
located in the passenger compartment fuse
box.
SDI2654
ENGINE COMPARTMENT
CAUTION
Never use a fuse of a higher or lower
amperage rating than that specified on
the fuse box cover. This could damage
the electrical system or cause a fire.
NOTE:
If the extended storage fuse switch mal- CAUTION
functions or if the fuse is open, it is not
necessary to replace the switch. In this Be careful not to allow children to
case, remove the extended storage fuse swallow the battery and removed parts.
switch and replace it with a new fuse of the
same rating.
How to remove the extended storage fuse
switch:
1. To remove the extended storage fuse switch,
be sure the ignition switch is in the OFF or
LOCK position.
SDI2705 2. Be sure the headlight switch is in the OFF
position.
Extended storage fuse switch (if so 3. Remove the fuse box cover.
equipped) 4. Pinch the storage fuse switch and pull it in
To reduce battery drain, the extended storage the direction illustrated.
fuse switch comes from the factory switched off.
Prior to delivery of your vehicle, the switch is
pushed in (switched on) and should always
remain on.
If the extended storage fuse switch is not
pushed in (switched on), the meter may display
a warning message. See “Extended storage fuse
warning message” (P.2-7).
If any electrical equipment does not operate,
remove the extended storage fuse switch and
check for an open fuse.
SDI2134
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
KEYFOB following two conditions: (1) This device
Replace the battery in the keyfob as follows: may not cause harmful interference, and
(2) this device must accept any interfer-
1. Remove the screw. ence received, including interference that
2. Insert a small screwdriver into the slit of the may cause undesired operation.
corner and twist it to separate the upper part Note: Changes or modifications not ex-
from the lower part. Use a cloth to protect pressly approved by the party responsible
Maintenance and do-it-yourself 8-23
2. Insert a small screwdriver into the slit of the
corner and twist it to separate the upper part
from the lower part. Use a cloth to protect
the casing.
3. Replace the battery with a new one.
Recommended battery:
CR2025 or equivalent
. Do not touch the internal circuit and
electric terminals as doing so could
cause a malfunction.
. Hold the battery by the edges. Holding
the battery across the contact points will
seriously deplete the storage capacity. SDI2452
. Make sure that the + side faces the
4. Align the tips of the upper and lower parts
bottom of the case.
* 1 , and then push them together *
2 until it
is securely closed.
5. Operate the buttons to check its operation.
See a NISSAN dealer if you need any assistance
for replacement.
SDI2451 FCC Notice:
INTELLIGENT KEY For USA:
Replace the battery in the Intelligent Key as This device complies with Part 15 of the
follows: FCC Rules. Operation is subject to the
following two conditions: (1) This device
1. Remove the mechanical key from the In-
may not cause harmful interference, and
telligent Key.
(2) this device must accept any interfer-
ence received, including interference that
1. Map light
2. Front side marker light
3. Front fog light (if so equipped)
4. Headlight (high-beam/low-beam)
5. Front turn signal light
6. Front parking light
7. Side turn signal light
8. Daytime running light (NISMO models)
9. High-mounted stop light
10. Back-up light
11. Stop light
12. Rear turn signal/tail/rear side marker light
13. License plate light
14. Cargo light
JVM0264X
CAUTION
. Do not leave the bulb out of the
headlight reflector for a long period
of time. Dust, moisture, smoke, etc.
entering the headlight body may
affect bulb performance.
. High pressure halogen gas is sealed SDI2687
inside the halogen bulb. The bulb Disconnect the battery negative cable before
may break if the glass envelope is replacing bulbs.
scratched or the bulb is dropped.
1. Remove the connector.
. Only touch the base when handling
the bulb. Never touch the glass 2. Turn the holder *
A and then pull out it.
: REMOVE
: INSTALL
Replacement procedures
All other lights are either type A, B, C, D or E.
When replacing a bulb, first remove the lens
and/or cover.
SDI2653
Cargo light
If you have a flat tire, see “Flat tire” (P.6-3). and Loading Information label is affixed to Loading Information label. Do
TIRE PRESSURE the driver side center pillar. Tire pressures not load your vehicle beyond
should be checked regularly because: this capacity. Overloading your
Tire Pressure Monitoring System (TPMS)
. Most tires naturally lose air over time. vehicle may result in reduced
This vehicle is equipped with the Tire Pressure
. Tires can lose air suddenly when driven tire life, unsafe operating condi-
Monitoring System (TPMS). It monitors tire
pressure of all tires except the spare. When over potholes or other objects or if the tions due to premature tire fail-
the low tire pressure warning light is lit, and the vehicle strikes a curb while parking. ure, or unfavorable handling
CHECK TIRE PRES (pressure) warning mes- The tire pressures should be checked characteristics and could also
sage is displayed in the vehicle information when the tires are cold. The tires are lead to a serious accident. Load-
display, one or more of your tires is significantly considered COLD after the vehicle has ing beyond the specified capa-
under-inflated. been parked for 3 or more hours, or driven city may also result in failure of
The TPMS will activate only when the vehicle is less than 1 mile (1.6 km) at moderate other vehicle components.
driven at speeds above 16 MPH (25 km/h). speeds. . Before taking a long trip, or
Also, this system may not detect a sudden drop
in tire pressure (for example a flat tire while Incorrect tire pressure, including un- whenever you heavily load your
driving). der inflation, may adversely affect tire vehicle, use a tire pressure
For more details, see “Low tire pressure warning life and vehicle handling. gauge to ensure that the tire
light” (P.2-15), “Tire Pressure Monitoring Sys- pressures are at the specified
tem (TPMS)” (P.5-4) and “Tire Pressure Mon- level.
WARNING
itoring System (TPMS)” (P.6-3). . For additional information re-
Tire inflation pressure . Improperly inflated tires can fail garding tires, refer to “Important
suddenly and cause an accident. Tire Safety Information” (US) or
Check the pressure of the tires (including
. The Gross Vehicle Weight rating “Tire Safety Information” (Cana-
the spare) often and always prior to long
(GVWR) is located on the F.M.V. da) in the Warranty Information
distance trips. The recommended tire
S.S./C.M.V.S.S. certification la- Booklet.
pressure specifications are shown on the
Tire and Loading Information label under bel. The vehicle weight capacity
the “Cold Tire Pressure” heading. The Tire is indicated on the Tire and
8-30 Maintenance and do-it-yourself
hours, or driven less than 1 mile (1.6
km) at moderate speeds. The recom-
mended cold tire inflation is set by the
manufacturer to provide the best
balance of tire wear, vehicle handling,
driveability, tire noise, etc., up to the
vehicle’s GVWR.
*
5 Tire size — see “Tire labeling” (P.8-
35).
*
6 Spare tire size or compact spare tire
size (if so equipped)
SDI2503
*
1 Tire size (example: P215/60R16 94H) *2 TIN (Tire Identification Number) for a
1. P: The “P” indicates the tire is designed new tire (example: DOT XX XX XXX XXXX)
for passenger vehicles. (Not all tires 1. DOT: Abbreviation for the “Department
have this information.) of Transportation”. The symbol can be
2. Three-digit number (215): This number placed above, below or to the left or
gives the width in millimeters of the tire right of the Tire Identification Number.
from sidewall edge to sidewall edge. 2. Two-digit code: Manufacturer’s identifi-
3. Two-digit number (60): This number, cation mark
known as the aspect ratio, gives the 3. Two-digit code: Tire size
tire’s ratio of height to width. 4. Three-digit code: Tire type code (Op-
4. R: The “R” stands for radial. tional)
WARNING
. After rotating the tires, check
and adjust the tire pressure.
. Retighten the wheel nuts when
the vehicle has been driven for
SDI1662 600 miles (1,000 km) (also in SDI1663
cases of a flat tire, etc.).
CHANGING WHEELS AND TIRES 1. Wear indicator
. Do not include the spare tire or 2. Wear indicator location mark
Tire rotation any other small size spare tire in
Tire wear and damage
NISSAN recommends rotating the tires the tire rotation.
every 5,000 miles (8,000 km). (See “Flat . For additional information re-
tire” (P.6-3) for tire replacing procedures.) garding tires, refer to “Important WARNING
As soon as possible, tighten the wheel Tire Safety Information” (US) or
. Tires should be periodically in-
nuts to the specified torque with a “Tire Safety Information” (Cana-
spected for wear, cracking, bul-
torque wrench. da) in the Warranty Information
ging or objects caught in the
Wheel nut tightening torque: Booklet.
tread. If excessive wear, cracks,
80 ft-lb (108 N·m) bulging or deep cuts are found,
the tire(s) should be replaced.
. The original tires have built-in
The wheel nuts must be kept tigh-
tread wear indicators. When
Maintenance and do-it-yourself 8-39
wear indicators are visible, the Replacing wheels and tires driving conditions and cause an
tire(s) should be replaced. When replacing a tire, use the same size, tread accident and personal injury.
design, speed rating and load carrying capacity . If the wheels are changed for any
. Tires degrade with age and use. as originally equipped. (See “Specifications” reason, always replace with wheels
Have tires, including the spare, (P.9-8) for recommended types and sizes of which have the same off-set dimen-
over 6 years old checked by a tires and wheels.) sion. Wheels of a different off-set
qualified technician, because could cause premature tire wear,
some tire damage may not be degrade vehicle handling character-
obvious. Replace the tires as
WARNING
istics and/or interference with the
necessary to prevent tire failure . The use of tires other than those brake discs/drums. Such interfer-
and possible personal injury. recommended or the mixed use of ence can lead to decreased braking
. Improper service of the spare tires of different brands, construc- efficiency and/or early brake pad/
tion (bias, bias-belted or radial), or shoe wear. See “Wheels and tires”
tire may result in serious perso-
tread patterns can adversely affect (P.9-8) of this manual for wheel off-
nal injury. If it is necessary to set dimensions.
repair the spare tire, contact a the ride, braking, handling, ground
clearance, body-to-tire clearance, . When a spare tire is mounted or a
NISSAN dealer. wheel is replaced, the TPMS will not
tire chain clearance, speedometer
. For additional information re- calibration, headlight aim and bum- function and the low tire pressure
garding tires, refer to “Important per height. Some of these effects warning light will flash for approxi-
Tire Safety Information” (US) or may lead to accidents and could mately 1 minute. The light will
“Tire Safety Information” (Cana- result in serious personal injury. remain on after 1 minute. Contact
da) in the Warranty Information . For Two-Wheel Drive (2WD) models, your NISSAN dealer as soon as
if your vehicle was originally possible for tire replacement and/
Booklet.
equipped with 4 tires that were the or system resetting.
same size and you are only repla- . Replacing tires with those not ori-
cing 2 of the 4 tires, install the new ginally specified by NISSAN could
tires on the rear axle. Placing new affect the proper operation of the
tires on the front axle may cause TPMS.
loss of vehicle control in some
8-40 Maintenance and do-it-yourself
. Do not install a damaged or de- . Only use spare tires specified for Care of wheels
formed wheel or tire even if it has each AWD model. See “Cleaning exterior” (P.7-2) for details about
been repaired. Such wheels or tires care of the wheels.
could have structural damage and If excessive tire wear is found, it is recom-
could fail without warning. mended that all four tires be replaced with tires
Spare tire
of the same size, brand, construction and tread When a spare tire is mounted (TEMPORARY
. The use of retread tire is not re-
pattern. The tire pressure and wheel alignment USE ONLY), the TPMS will not function.
commended.
should also be checked and corrected as Observe the following precautions if the TEM-
. For additional information regard-
necessary. Contact a NISSAN dealer. PORARY USE ONLY spare tire must be used,
ing tires, refer to “Important Tire
otherwise your vehicle could be damaged or
Safety Information” (US) or “Tire Wheel balance involved in an accident.
Safety Information” (Canada) in the Unbalanced wheels may affect vehicle handling
Warranty Information Booklet. and tire life. Even with regular use, wheels can
get out of balance. Therefore, they should be WARNING
All-Wheel Drive (AWD) models balanced as required.
. The TEMPORARY USE ONLY spare
Wheel balance service should be per-
tire should be used for emergency
formed with the wheels off the vehicle.
CAUTION Spin balancing the wheels on the vehicle
use. It should be replaced with the
standard tire at the first opportunity
could lead to mechanical damage.
. Always use tires of the same size, to avoid possible tire or differential
brand, construction (bias, bias- For additional information regarding tires, refer damage.
belted or radial), and tread pattern to “Important Tire Safety Information” (US) or
. Drive carefully while the TEMPOR-
on all four wheels. Failure to do so “Tire Safety Information” (Canada) in the War-
ARY USE ONLY spare tire is in-
may result in a circumference differ- ranty Information Booklet.
stalled. Avoid sharp turns and
ence between tires on the front and
abrupt braking while driving.
rear axles which will cause exces-
sive tire wear and may damage the . Periodically check spare tire infla-
transmission, transfer case and rear tion pressure. Always keep the
differential gears. pressure of the TEMPORARY USE
ONLY spare tire at 60 psi (420 kPa,
4.2 bar).
Maintenance and do-it-yourself 8-41
. With the TEMPORARY USE ONLY . Because the TEMPORARY USE
spare tire installed do not drive your ONLY spare tire is smaller than the
vehicle at speeds faster than 50 original tire, ground clearance is
MPH (80 km/h). reduced. To avoid damage to the
. When driving on roads covered with vehicle, do not drive over obstacles.
snow or ice, the TEMPORARY USE Also do not drive the vehicle
ONLY spare tire should be used on through an automatic car wash
the rear wheels and original tire since it may get caught.
used on the front wheels (drive
wheels). Use tire chains only on
the front (original) tires.
. Tire tread of the TEMPORARY USE
ONLY spare tire will wear at a faster
rate than the standard tire. Replace
the spare tire as soon as the tread
wear indicators appear.
. Do not use the spare tire on other
vehicles.
. Do not use more than one spare tire
at the same time.
CAUTION
. Do not use tire chains on a TEM-
PORARY USE ONLY spare tire. Tire
chains will not fit properly and may
cause damage to the vehicle.
Capacities and recommended fuel/lubricants ................... 9-2 Installing front license plate ................................................ 9-13
Fuel information ................................................................... 9-4 Vehicle loading information ................................................. 9-14
Engine oil and oil filter recommendation ....................... 9-6 Terms ................................................................................. 9-14
Air conditioning system refrigerant and Vehicle load capacity .................................................... 9-15
lubricant recommendations ............................................... 9-7 Loading tips ..................................................................... 9-16
Specifications ............................................................................. 9-8 Measurement of weights .............................................. 9-16
Engine .................................................................................... 9-8 Towing a trailer ....................................................................... 9-17
Wheels and tires ................................................................. 9-8 Flat towing ............................................................................... 9-17
Dimensions and weights ................................................... 9-9 Continuously Variable Transmission (CVT) ............. 9-17
When traveling or registering your vehicle in Manual Transmission ..................................................... 9-17
another country .......................................................................... 9-9 Uniform tire quality grading ................................................. 9-18
Vehicle identification .............................................................. 9-10 Treadwear ........................................................................ 9-18
Vehicle Identification Number (VIN) plate .................. 9-10 Traction AA, A, B and C .............................................. 9-18
Vehicle identification number (chassis number) ....... 9-10 Temperature A, B and C .............................................. 9-18
Engine serial number ....................................................... 9-10 Emission control system warranty ..................................... 9-19
F.M.V.S.S./C.M.V.S.S. certification label .................... 9-11 Reporting safety defects ..................................................... 9-19
Emission control information label ............................... 9-11 Readiness for Inspection/Maintenance (I/M) test ......... 9-20
Tire and Loading Information label .............................. 9-11 Event Data Recorders (EDR) ............................................. 9-21
Air conditioner specification label ................................ 9-12 Owner’s manual/service manual order information ...... 9-21
CAPACITIES AND RECOMMENDED
FUEL/LUBRICANTS
The following are approximate capacities. The actual refill capacities may be a little different. When refilling, follow the procedure
instructed in the “8. Maintenance and do-it-yourself” section to determine the proper refill capacity.
Capacity (Approximate) Recommended specifications
US measure Imp measure Liter
2WD model 13-1/4 gal 11 gal 50
Fuel See “Fuel information” (P.9-4).
AWD model 11-7/8 gal 9-7/8 gal 45
With oil filter change 4-3/4 qt 4 qt 4.5 . For additional information, see “Engine oil” (P.8-8) for changing
engine oil.
. NISSAN recommends Genuine NISSAN Ester Oil available at a
NISSAN dealer.
Engine oil . Genuine NISSAN engine oil or equivalent
Drain and refill Without oil filter change 4-1/2 qt 3-3/4 qt 4.3 . Engine oil with API Certification Mark
. Viscosity SAE 5W-30
. For additional information, see “Engine oil and oil filter recommen-
dation” (P.9-6).
Cooling system
CVT model 8-5/8 qt 7-1/8 qt 8.1
With reservoir Pre-diluted Genuine NISSAN Long Life Antifreeze/Coolant (blue) or
MT model 8-3/8 qt 7 qt 7.9
equivalent
Reservoir 5/8 qt 1/2 qt 0.6
. Use only Genuine NISSAN CVT Fluid NS-2. Using transmis-
sion fluid other than Genuine NISSAN CVT Fluid NS-2 will
Continuously Variable Transmission (CVT) fluid — — — damage the CVT, which is not covered by the NISSAN new
vehicle limited warranty.
. Genuine NISSAN CVT Fluid NS-2
For NISMO RS models
. Genuine NISSAN Manual Transmission Fluid (MTF) HQ Multi 75W-
85 or equivalent
. If Genuine NISSAN Manual Transmission Fluid (MTF) HQ Multi 75W-
85 is hard to obtain, API GL-4, Viscosity SAE 75W-85 may be used
as a temporary replacement. However, use Genuine NISSAN gear oil
as soon as it is available.
Manual Transmission (MT) gear oil — — — Except for NISMO RS models
. Genuine NISSAN Manual Transmission Fluid (MTF) TL/JR Type
75W-80 or equivalent
. If Genuine NISSAN Manual Transmission Fluid (MTF) TL/JR Type is
not available, API GL-4+, Viscosity SAE 75W-80 may be used as a
temporary replacement. However, use Genuine NISSAN Manual
Transmission Fluid (MTF) TL/JR Type as soon as it is available.
JVT0159X
This spark ignition system complies with the Canadian standard ICES-002.
8. Install the license plate bracket with the . GVW (Gross Vehicle Weight) - curb
screws. WARNING weight plus the combined weight of
9. Install the license plate with bolts that are passengers and cargo.
not longer than 0.55 in (14 mm). . It is extremely dangerous to ride . GVWR (Gross Vehicle Weight Rating)
in a cargo area inside the vehi- - maximum total combined weight of the
cle. In a collision, people riding unloaded vehicle, passengers, luggage,
in these areas are more likely to hitch, trailer tongue load and any other
be seriously injured or killed. optional equipment. This information is
. Do not allow people to ride in located on the F.M.V.S.S./C.M.V.S.S.
any area of your vehicle that is label.
not equipped with seats and . GAWR (Gross Axle Weight Rating) -
seat belts. maximum weight (load) limit specified
. Be sure everyone in your vehicle for the front or rear axle. This informa-
is in a seat and using a seat belt tion is located on the F.M.V.S.S./C.M.V.
properly. S.S. label.
. GCWR (Gross Combined Weight Rat-
TERMS ing) - The maximum total weight rating
It is important to familiarize yourself with the of the vehicle, passengers, cargo, and
following terms before loading your vehicle: trailer.
. Curb Weight (actual weight of your . Vehicle Capacity Weight, Load limit,
vehicle) - vehicle weight including: Total load capacity - maximum total
standard and optional equipment, weight limit specified of the load
fluids, emergency tools, and spare tire (passengers and cargo) for the vehicle.
assembly. This weight does not in- This is the maximum combined weight
clude passengers and cargo. of occupants and cargo that can be
loaded into the vehicle. If the vehicle is
used to tow a trailer, the trailer tongue
9-14 Technical and consumer information
weight must be included as part of the
cargo load. This information is located
on the Tire and Loading Information
label.
. Cargo capacity - permissible weight of
cargo, the subtracted weight of occu-
pants from the load limit.
VEHICLE LOAD CAPACITY
Do not exceed the load limit of your vehicle
shown as “The combined weight of occu-
pants and cargo” on the Tire and Loading
Information label. Do not exceed the
number of occupants shown as “Seating
Capacity” on the Tire and Loading Informa-
tion label.
To get “the combined weight of occupants
and cargo”, add the weight of all occu-
pants, then add the total luggage weight.
Examples are shown in the following STI0447
illustration.
Steps for determining correct load limit 2. Determine the combined weight of the
1. Locate the statement “The combined driver and passengers that will be riding
weight of occupants and cargo should in your vehicle.
never exceed XXX kg or XXX lbs” on 3. Subtract the combined weight of the
your vehicle’s placard. driver and passengers from XXX kg or
XXX lbs.
Do not tow a trailer with your vehicle. Towing your vehicle with all four wheels on the
12).
ground is sometimes called flat towing. This
method is sometimes used when towing a
vehicle behind a recreational vehicle, such as a
CONTINUOUSLY VARIABLE TRANS-
motor home. MISSION (CVT)
All-Wheel Drive (AWD) models:
Do not tow an AWD vehicle with any of the
CAUTION wheels on the ground.
. Failure to follow these guidelines Two-Wheel Drive (2WD) models:
can result in severe transmission To tow a vehicle equipped with a Continuously
damage. Variable Transmission (CVT), an appropriate
. Whenever flat towing your vehicle, vehicle dolly MUST be placed under the towed
always tow forward, never back- vehicle’s driving wheels. Always follow the dolly
ward. manufacturer’s recommendations when using
their product.
. DO NOT tow any Continuously Vari-
able Transmission (CVT) vehicle MANUAL TRANSMISSION
with all four wheels on the ground . Always tow with the manual transmission in
(flat towing). Doing so WILL DA- Neutral.
MAGE internal transmission parts . Your vehicle speed should never exceed 70
due to lack of transmission lubrica- MPH (112 km/h) when flat towing your
tion. vehicle.
. DO NOT tow an All-Wheel Drive . After towing 500 miles (805 km), start and
(AWD) vehicle with any of the idle the engine with the transmission in
wheels on the ground. Doing so Neutral for two minutes. Failure to idle the
may cause serious and expensive engine after every 500 miles (805 km) of
damage to the powertrain. towing may cause damage to the transmis-
. For emergency towing procedures sion’s internal parts.
refer to “Towing your vehicle” (P.6-
10-5
Three-way catalyst........................................................ 5-4 Traveling or registering your vehicle in W
Tilt steering column.................................................... 3-23 another country.............................................................. 9-9
Tire pressure, Low tire pressure warning light.... 2-15 Trip computer............................................................... 2-10 Warning
Tires Troubleshooting guide ............................................... 4-97 Hazard warning flasher switch............................. 6-2
Flat tire....................................................................... 6-3 Turn signal switch....................................................... 2-38 Lights....................................................................... 2-13
Low tire pressure warning system...................... 5-4 Tire pressure monitoring
Tire and Loading information label....... 8-31, 9-11 U system (TPMS)............................................... 5-4, 6-3
Tire chains.............................................................. 8-38 Warning/indicator lights and
Tire dressing............................................................. 7-4 Underbody cleaning ..................................................... 7-3 audible reminders................................................. 2-12
Tire pressure ......................................................... 8-30 Uniform tire quality grading ...................................... 9-18 Warning labels, Air bag warning labels................. 1-52
Tire pressure monitoring USB interface............................................................... 4-62 Warning light
system (TPMS)............................................... 5-4, 6-3 USB memory operation............................................. 4-52 Air bag warning light................................ 1-52, 2-17
Tire rotation............................................................ 8-39 Using the system......................................................... 4-93 Anti-lock braking system (ABS)
Types of tires......................................................... 8-37 warning light.......................................................... 2-13
Uniform tire quality grading ............................... 9-18 V AWD warning light.............................................. 5-35
Wheel/tire size......................................................... 9-8 Brake warning light.............................................. 2-13
Wheels and tires.................................................. 8-30 Vanity mirror.................................................................. 3-27 Door open warning light..................................... 2-14
Tonneau cover (see cargo cover)........................... 2-44 Variable voltage control system............................... 8-14 Electric power steering warning light............. 2-14
Touch screen....................................................... 4-4, 4-10 Vehicle Intelligent Key system warning light................ 2-14
Towing Dimensions and weights....................................... 9-9 Low fuel warning light......................................... 2-15
Flat towing............................................................. 9-17 Identification number (VIN)................................ 9-10 Low tire pressure warning light........................ 2-15
Tow truck towing.................................................. 6-12 Information display.................................................. 2-9 Seat belt warning light........................................ 2-16
Towing a trailer..................................................... 9-17 Loading information............................................. 9-14 Warranty, Emission control system warranty....... 9-19
TPMS, Tire pressure monitoring system................. 5-4 Recovery (freeing a stuck vehicle) .................. 6-14 Washer switch
TPMS, Tire pressure warning system...................... 6-3 Security system.................................................... 2-29 Rear window wiper and washer switch......... 2-34
Traffic info setup............................................................ 4-9 Vehicle dynamic control (VDC) off switch..... 2-39 Windshield wiper and washer switch............. 2-32
Trailer towing................................................................ 9-17 Vehicle dynamic control (VDC) system.......... 5-41 Washing........................................................................... 7-2
Transmission Vehicle phonebook..................................................... 4-87 Waxing............................................................................. 7-3
Continuously Variable Transmission Ventilators...................................................................... 4-19 Weights (See dimensions and weights)................. 9-9
(CVT) fluid.............................................................. 8-11 Voice command........................................................... 4-86 Wheel/tire size............................................................... 9-8
Driving with CVT (Continuously Voice command (Bluetooth® Hands-Free Wheels and tires......................................................... 8-30
Variable Transmission) ............................. 5-11, 5-17 Phone System) ............................................................ 4-78 Care of wheels ........................................................ 7-4
Driving with manual transmission.......... 5-11, 5-23 Voice Prompt Interrupt............................................... 4-86 Cleaning aluminum alloy wheels......................... 7-4
Transmission shift lever lock release............... 5-22 Window washer fluid................................................. 8-12
Transmitter (See remote keyless entry system) .... 3-7 Window(s)
Transmitter, With Intelligent Key system Cleaning .................................................................... 7-3
(See Intelligent Key system)..................................... 3-16 Power windows.................................................... 2-45
10-6
Windshield wiper and washer switch.................... 2-32
Wiper
Rear window wiper and washer switch......... 2-34
Rear window wiper blade.................................. 8-18
Windshield wiper and washer switch............. 2-32
Wiper blades......................................................... 8-17
X
XM setup......................................................................... 4-7
10-7
MEMO
MEMO
MEMO
MEMO
MEMO
MEMO
GAS STATION INFORMATION