Bearing Gard

Bearing Gard TM
bearing isolator
Bearing Gard protection technology

delivers reliable isolation from
contamination to keep bearings
running cleaner longer.
Designed to offer superior protection

for your bearing housing
Installation
Bearing Gard bearing isolators directly assist
alignment notch
equipment reliability by creating a strong
barrier against external contamination.
Secure pressfit Protected interface
• Static protection is assured by an internal in the housing
O-ring between the rotor and stator. Oversized
contamination
• Dynamic protection is provided by a tortuous
channel
labyrinth that effectively repels severe
environmental conditions.
Unique double
• Standard design accommodates axial shaft drive ring design
movement of 0.63 mm (0.025 inch) TIR
• Static sealing quickly transitions to non-contacting Optimized oil collection
operation for consistent performance and will not chamber
wear on the shaft or equipment.
Innovative
• Oil retention features work to keep oil inside static labyrinth
the bearings and off the ground. shut-off
Protected
oil outlet
D AY
Superior
M E G
S A I N
IPP BLE
contaminant
outlet
S H
A I LA
AV
Working to keep industry running, Flowserve offers the Bearing Gard with
same day shipping of equipment-specific and made to order designs
We are continuously expanding our product range and custom
engineered solutions. Your local Flowserve representative will
guide you through the selection and ordering process.
General guidelines for made to order designs with same day shipping
• Shaft diameter: 23 - 203 mm (0.875 - 8.000 inch)
• Housing bore: 20 - 50 mm (0.750 - 2.000 inch) over
shaft diameter for shaft sizes up to 150 mm (6.000 inch)
• Housing bore: 25 - 50 mm (1.000 - 2.000 inch) over Housing bore up to 8.3 mm
shaft diameter for shaft sizes over 150 mm (6.000 inch) 136 mm (5.375") (0.325")
• Axial insertion/extension: see cross section view Housing bore over 9.5 mm
• Maximum axial movement: 0.63 mm (0.025 inch) TIR 136 mm (5.375") (0.375") 9.5 mm
(0.375")
• Maximum radial runout: 0.13 mm (0.005 inch) TIR
• Speed: up to 30 m/s (100 ft/s)
• Rotor and Stator: Bronze
• O-rings: Fluoroelastomer
• Bearing lubrication: oil splash, grease, oil mist,
dry lubrication, non-flooded conditions
Bearing Gard isolators fit a wide

range of rotating equipment
Typical applications include pumps, motors, gearboxes,
and general lip seal replacements. Equipment-specific
Bearing Gard designs are available or Flowserve will
rapidly design a custom solution.
In addition to extensive in-house hurricane simulation
testing, the Bearing Gard meets or exceeds the following
industry standards and certifications:
• API 610 • IEEE-841
USA and Canada
• IP-66 • ATEX Kalamazoo, Michigan USA
Telephone: 1 269 381 2650
FSD257eng REV 07-15 Printed in USA Telefax: 1 269 382 8726
To find your local Flowserve representative Europe, Middle East, Africa

and find out more about Flowserve Corporation visit Roosendaal, The Netherlands
www.flowserve.com Telephone: 31 165 581400
Telefax: 31 165 554590
Flowserve Corporation has established industry leadership in the design and manufacture of its products. When properly selected, this Asia Pacific
Flowserve product is designed to perform its intended function safely during its useful life. However, the purchaser or user of Flowserve
products should be aware that Flowserve products might be used in numerous applications under a wide variety of industrial service
Singapore
conditions. Although Flowserve can provide general guidelines, it cannot provide specific data and warnings for all possible applications. The
purchaser/user must therefore assume the ultimate responsibility for the proper sizing and selection, installation, operation, and maintenance
Telephone: 65 6544 6800
of Flowserve products. The purchaser/user should read and understand the Installation Instructions included with the product, and train its Telefax: 65 6214 0541
employees and contractors in the safe use of Flowserve products in connection with the specific application.
While the information and specifications contained in this literature are believed to be accurate, they are supplied for informative purposes
only and should not be considered certified or as a guarantee of satisfactory results by reliance thereon. Nothing contained herein is to Latin America
be construed as a warranty or guarantee, express or implied, regarding any matter with respect to this product. Because Flowserve is
continually improving and upgrading its product design, the specifications, dimensions and information contained herein are subject to
Mexico City
change without notice. Should any question arise concerning these provisions, the purchaser/user should contact Flowserve Corporation Telephone: 52 55 5567 7170
at any one of its worldwide operations or offices.
Telefax: 52 55 5567 4224
© 2015 Flowserve Corporation

Bearing Gard

Uploaded by

Copyright:

Available Formats

Bearing Gard

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Bearing Gard

Uploaded by

Copyright:

Available Formats

Bearing Gard TM

Bearing Gard protection technology

Designed to offer superior protection

Bearing Gard isolators fit a wide

To find your local Flowserve representative Europe, Middle East, Africa

You might also like