Internal Forced Convection

Chapter 8
Internal Forced Convection

8.1 Hydrodynamic Considerations
8.1.1 Flow Conditions
may be determined experimentally, as shown in Figs. 7.1-7.2.
ρ um D
ReD ≡ (8.1)
μ
where um is the mean fluid velocity over the tube cross section.
The critical ReD corresponding to the onset of turbulence is
ReD ,c ≈ 2300 (8.2)
The entrance length for laminar flow is
⎛ x fd,h ⎞
⎜ D ⎟ ≈ 0.05 Re D (8.3)
⎝ ⎠ lam
The entrance length for turbulent flow is approximately indep. of Re
⎛ x fd,h ⎞
10 ≤ ⎜ ⎟ ≤ 60 (8.4)
⎝ D ⎠ turb
8.1.2 The mean Velocity
um =
∫ A
c
ρ u (r , x)dAc 2 r
= 2 ∫ u (r , x)rdr
0
(8.8)
ρ Ac r0 0
8.1.3 Velocity Profile in the Fully Developed Region
The velocity profile of a fully developed laminar flow is parabolic
as shown in (8.13)-(8.15).
1 ⎛ dp ⎞ 2 ⎡ ⎛r⎞ ⎤
2
u (r ) = − ⎜ ⎟ r0 ⎢1 − ⎜ ⎟ ⎥ (8.13)
4 μ ⎝ dx ⎠ ⎢ ⎝ r0 ⎠ ⎥
⎣ ⎦
8.1.4 Pressure Gradient and Friction Factor in Fully Developed Flow
Friction factor for laminar flow:
f = 64 (8.19)
ReD
Friction factor for turbulent flow: (8.20) or (8.21) or Fig. 8.3.
Pressure drop:
p ρ um2 x ρ um2
Δp = − ∫ dp = f ∫ dx = f ( x2 − x1 )
2 2
(8.22a)
p 1 2D x 1 2D
8.2 Thermal Considerations
The thermal entrance length for laminar flow is

⎛ xfd,t ⎞
⎜ D ⎟ ≈ 0.05 ReD Pr (8.23)
⎝ ⎠lam
The thermal entrance length for turbulent flow is
⎛ xfd,t ⎞
⎜ D ⎟ ≈ 10
⎝ ⎠ turb (8.24)
8.2.1 The Mean Temperature
∫ ρuc TdA
p c
Tm = (8.25)
Ac
m& c p
For incompressible flow in a circular tube with constant cp,
Tm = 2 r0
2 ∫0 uTrdr (8.26)
um r 0
8.2.2 Newton's Law of Cooling
qs = h(Ts − T m )
"
(8.27)
where h is the local convection heat transfer coefficient.
This relation applies for different wall conditions, e.g., Ts= C or
q”= C.
Since Tm usually varies along the tube, the variation of Tm must
be accounted for.
8.2.3 Fully Developed Conditions
The thermally fully developed condition is when the relative shape
of the profile no longer changes and is stated as
∂ ⎡ T s (x) − T (r, x) ⎤ = 0 (8.28)
⎢ ⎥
∂ x ⎣ T s ( x) − T m ( x) ⎦ fd,t
for cases with either a uniform surface heat flux or a uniform surface
temperature. Since the term in the bracket of (8.29) is independent
of x, its r-derivative is also independent of x. So,
∂ ⎛ Ts − T ⎞ −∂T / ∂r r =r
⎜ ⎟ =
0
= − h ≠ f (x) (8.29)
∂r ⎝ Ts − Tm ⎠ r =r Ts − Tm k
0
Hence, in the thermally fully developed

flow of a fluid with constant properties,
the local convection coefficient is a
constant. (Fig. 8.5)
Eq. (8.28) implies
∂T ∂ Tm ∂ (T − Tm )
= or = 0, qs" = constant (8.32)
∂ x fd,t ∂ x fd,t ∂x fd,t
∂T (Ts − T ) ∂ Tm
= , Ts = constant (8.33)
∂x fd,t (Ts − Tm ) ∂ x fd,t
Tm(x) is a very important variable for internal flows and may be

obtained by applying an overall energy balance to the flow.
EX 8.1
8.3 The Energy Balance
8.3.1 General Considerations
Energy conservation for a differential
control volume of Fig. 8.6 leads to
dqconv = m& c p dTm (8.36)
dTm qs" P
or = = P h(Ts − Tm ) (8.37)
& p mc
dx mc & p
8.3.2 Constant Surface Heat Flux
qs" P
Tm ( x) = Tm ,i + x, qs" = constant (8.40)
& p
mc
EX. 8.2
8.3.3 Constant Surface Temperature
Define ΔT = Ts - Tm, Eq. 8.37 becomes
dTm d ( ΔT )
=− = P h ΔT
dx dx m& c p
Integration leads to
ΔTo ⎛
⎜ ∫0 1 hdx ⎞⎟ = − PL hL
L
ln =− PL
ΔTi m& c p ⎝ L ⎠ m& c p (8.41a)
Ts − Tm ( x) ⎛ Px ⎞
Then, = exp ⎜ − h ⎟ , Ts = constant (8.42)
Ts − Tm,i ⎝ &
mc p ⎠
From energy balance,
qconv = m& c p (Tm ,o − Tm ,i ) = m& c p [(Ts − Tm ,i ) − (Ts − Tm ,o )] = m& c p ( ΔTi − ΔTo )
Substituting for m& c p from (8.41a), we obtain
ΔTo − ΔTi
qconv = hAs ΔTlm , ΔTlm ≡ , Ts = constant (8.44)
ln(ΔTo / ΔTi )
This means for constant Ts, the total qconv is proportional to h and
the log mean temperature difference ΔTlm.
In many applications, the temperature of an external fluid, rather
than the tube surface temperature, is fixed (Fig. 8.8). The
previous formulae can still be applied (with modification
adopting the concept of thermal resistance), as indicated by Eqs.
(8.45) and (8.46).
ΔTo T∞ − Tm ,o ⎛ UA ⎞
= = exp ⎜ − s ⎟ (8.45a)
ΔTi T∞ − Tm ,i & p⎠
⎝ mc
q = UAs ΔTlm (8.45b)
ΔTo T∞ − Tm ,o ⎛ 1 ⎞
= = exp ⎜ − ⎟
ΔTi T∞ − Tm ,i ⎝ &
mc p Rtot ⎠
(8.46a)
ΔTlm
q= (8.46b)
Rtot
EX 8.3
8.4 Laminar Flow in Circular Tubes: Thermal Analysis
8.4.1 The Fully Developed Region
For the case of uniform surface heat flux, the exact correlation is
Nu D ≡ hD = 4.36, qs" = constant (8.53)
k
For the case of constant surface temp., with (∂ T/∂ x) << (∂ T/∂ r)
2 2 2 2
NuD = 3.66, Ts = constant (8.55)
EXs. 8.4, 8.5

8.4.2 The Entry Region
Thermal entry length problem → (8.56)
Combined entry length problem → (8.57)
Fully Developed Pipe Flow
For Pr < 1 entrance fully-developed

region region
velocity boundary layer

thermal boundary layer
8.5 Convection Correlations: Turbulent Flow in Circular Tubes
Using the modified Reynolds analogy, there are (8.58)-(8.60).
(Note the exponent of ReD is 4/5).
For higher accuracies, use (8.61)-(8.62).
EX 8.6
8.6 Convection Correlations: Noncircular Tubes and the
Concentric Tube Annulus
Hydraulic diameter: Dh ≡ 4 Ac (8.66)
P
It is this diameter that should be used in calculating parameters such
as ReD and NuD.
For turbulent flow, it is reasonable to use the correlations of
Section 8.5 for Pr > 0.7. However, the coefficient is presumed
to be an average over the perimeter.
For laminar flow, the use of circular tube correlations is less
accurate, particularly with cross sections characterized by sharp
corners. For laminar fully developed conditions: use Table 8.1
Fully Developed Laminar Flow in Noncircular Tubes
Hydraulic diameter:
4 Ac
Dh ≡ P
hDh
Nu = = constant
k
f Re Dh = constant
∴ as Dh ↓
→ h and ΔP ↑
8.7 Heat Transfer Enhancement
Heat transfer enhancement may be achieved by increasing the
convection coefficient (inducing turbulence or secondary flow)
and/or by increasing the convection surface area. See Figs. 8.12
and 8.13
To induce secondary flow or turbulence
8.8 Microscale Internal Flow
Many new technologies involve microscale internal flow
with Dh≦100μm.
For gases, the results of Chapters 6 through 8 are not
expected to apply when Dh /λmfp ≦10.
For liquids, some features of previous results, e.g.,
friction factor (8.19), pressure drop (8.22a), and
transition criterion (8.2) remain applicable.
8.9 Convection Mass Transfer

Omitted.

Internal Forced Convection

Uploaded by

Copyright:

Available Formats

Internal Forced Convection

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Internal Forced Convection

Uploaded by

Copyright:

Available Formats

Chapter 8

Internal Forced Convection

The thermal entrance length for laminar flow is

Hence, in the thermally fully developed

Tm(x) is a very important variable for internal flows and may be

NuD = 3.66, Ts = constant (8.55)

EXs. 8.4, 8.5

For Pr < 1 entrance fully-developed

velocity boundary layer

8.9 Convection Mass Transfer

You might also like