Scribd Logo
Upload

Welcome to Scribd!

  • 1K views

    Honda Gx35

    Uploaded by

    kelumpj8479
    This is the maintenance manual of Honda GX35 small gasoline engine.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Honda Gx35

    Uploaded by

    kelumpj8479
    1K views1 page
    This is the maintenance manual of Honda GX35 small gasoline engine.

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This is the maintenance manual of Honda GX35 small gasoline engine.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    1K views1 page

    Honda Gx35

    Uploaded by

    kelumpj8479
    This is the maintenance manual of Honda GX35 small gasoline engine.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    GX35 Engine Adjustment Information

    VALVE CLEARANCE
    Valve clearance inspection and adjustment must be performed with the engine cold.
    ①. Remove the 5 x 14 mm top cover bolt and remove the top cover.
    ②. Remove the two 5 x 12 mm hex bolts from the head cover.
    ・Engine oil can leak out when removing the head cover. Catch the leaking oil with 1
    a suitable material and wipe up the area immediately.
    ③. Set the piston at top dead center of the compression stroke. Align the "△" mark on the 5 x 14 mm
    TOP COVER
    cam pulley with the cylinder head cover.
    BOLT
    ④. Insert a feeler gauge between the rocker arm and valve to measure the valve clearance. TOP COVER
    Valve clearance: 0.08 ± 0.02 mm (IN)
    0.11 ± 0.02 mm (EX)
    ⑤. If adjustment is necessary, proceed as follows:
    a. Loosen the adjusting screw lock nut and adjust the valve clearance by turning the
    adjusting screw right or left.
    b. Holding the adjusting screw with the tappet adjusting wrench, tighten the lock nut to
    the specification. TORQUE: 4.9 N·m (0.5 kgf·m, 3.9 lbf·ft)
    c. After tightening the lock nut, recheck the valve clearance.

    ADJUSTING
    2 3 ALIGNMENT MARK 4 5 SCREW
    HEAD COVER 5 x 12 mm
    HEX
    BOLT (2)
    ENGINE
    ASSEMBLY ADJUSTING
    SCREW
    LOCK NUT

    FEELER GAUGE

    CYLINDER HEAD CENTER ・To increase valve clearance, screw out.


    ・To decrease valve clearance, screw in.

    IGNITION COIL AIR GAP


    Adjustment is required only when the ignition coil or the flywheel has been removed.
    ①. Loosen the ignition coil bolts.
    Insert a feeler gauge between the ignition coil and the magnetic part of the flywheel.
    ②. Push the ignition coil firmly toward the flywheel and tighten the bolts.
    Specified clearance: 0.3 ± 0.1 mm (0.012 ± 0.004 in)
    ・Adjust the clearance at the magnetic part of the flywheel.
    ・Adjust both gaps at the right and left sides of the ignition coil simultaneously so they are equal.

    FEELER GAUGE 0.3 ± 0.1 mm


    (0.012 ± 0.004 in)

    0.3 ± 0.1 mm
    (0.012 ± 0.004 in)

    MAGNETIC PARTS

    See the shop manual for additional information. © Honda Motor Co., Ltd. 2010

    You might also like