Faculty Name : Mrs. R. N.

Ponnalagu Designation : Assistant Professor

Department : E.E.E. Faculty Code : EE 06
Subject Name : Electromagnetic Theory Subject Code : 131302
Year : II Semester : III
Degree & Branch : B.E. – E.E.E. Section : ‘B’

UNIT – 1 INTRODUCTION

Electromagnetic theory is a discipline concerned with the study of charges at rest and in
motion. Electromagnetic principles are fundamental to the study of electrical engineering and
physics. Electromagnetic theory is also indispensable to the understanding, analysis and
design of various electrical, electromechanical and electronic systems. Some of the
branches of study where electromagnetic principles find application are:

RF communication

Microwave Engineering

Antennas

Electrical Machines

Satellite Communication

Atomic and nuclear research

Radar Technology

Remote sensing

EMI EMC

Quantum Electronics

VLSI

Electromagnetic theory is a prerequisite for a wide spectrum of studies in the field of

Electrical Sciences and Physics. Electromagnetic theory can be thought of as generalization
of circuit theory. There are certain situations that can be handled exclusively in terms of field
theory. In electromagnetic theory, the quantities involved can be categorized as source
quantities and field quantities. Source of electromagnetic field is electric charges: either at
rest or in motion. However an electromagnetic field may cause a redistribution of charges
that in turn change the field and hence the separation of cause and effect is not always
visible.
Sources of EMF:
 Current carrying conductors.
 Mobile phones.
 Microwave oven.
 Computer and Television screen.
 High voltage Power lines.

Effects of Electromagnetic fields:

 Plants and Animals.
 Humans.
 Electrical components.

Fields are classified as

 Scalar field
 Vector field.

Electric charge is a fundamental property of matter. Charge exist only in positive or negative
integral multiple of electronic charge, -e, e= 1.60 × 10-19 coulombs. [It may be noted here
that in 1962, Murray Gell-Mann hypothesized Quarks as the basic building blocks of matters.
Quarks were predicted to carry a fraction of electronic charge and the existence of Quarks
have been experimentally verified.] Principle of conservation of charge states that the total
charge (algebraic sum of positive and negative charges) of an isolated system remains
unchanged, though the charges may redistribute under the influence of electric field.
Kirchhoff's Current Law (KCL) is an assertion of the conservative property of charges under
the implicit assumption that there is no accumulation of charge at the junction.

Electromagnetic theory deals directly with the electric and magnetic field vectors where as
circuit theory deals with the voltages and currents. Voltages and currents are integrated
effects of electric and magnetic fields respectively. Electromagnetic field problems involve
three space variables along with the time variable and hence the solution tends to become
correspondingly complex. Vector analysis is a mathematical tool with which electromagnetic
concepts are more conveniently expressed and best comprehended. Since use of vector
analysis in the study of electromagnetic field theory results in real economy of time and
thought, we first introduce the concept of vector analysis.

Vector Analysis:

The quantities that we deal in electromagnetic theory may be either scalar or vectors [There
are other class of physical quantities called Tensors: where magnitude and direction vary
with co ordinate axes]. Scalars are quantities characterized by magnitude only and algebraic
sign. A quantity that has direction as well as magnitude is called a vector. Both scalar and
vector quantities are function of time and position . A field is a function that specifies a
particular quantity everywhere in a region. Depending upon the nature of the quantity under
consideration, the field may be a vector or a scalar field. Example of scalar field is the
electric potential in a region while electric or magnetic fields at any point is the example of
vector field.
A vector can be written as, , where, is the magnitude and is the
unit vector which has unit magnitude and same direction as that of .

Two vector and are added together to give another vector . We have

................(1.1)

Let us see the animations in the next pages for the addition of two vectors, which has two
rules:

1: Parallelogram law and 2: Head & tail rule

Scaling of a vector is defined as , where is scaled version of vector and is a
scalar.
Some important laws of vector algebra are:
 Commutative Law..........................................(1.3)

Associative Law.............................................(1.4)

Distributive Law ............................................(1.5)

The position vector of a point P is the directed distance from the origin (O) to P, i.e., =
.

Fig 1.3: Distance Vector

If = OP and = OQ are the position vectors of the points P and Q then the distance
vector

Product of Vectors

When two vectors and are multiplied, the result is either a scalar or a vector depending
how the two vectors were multiplied. The two types of vector multiplication are:

Scalar product (or dot product) gives a scalar.

Vector product (or cross product) gives a vector.
The dot product between two vectors is defined as = |A||B|cosθAB ..................(1.6)

Vector product
is unit vector perpendicular to and
 Fig 1.4: Vector dot product

The dot product is commutative i.e., and distributive i.e.,

. Associative law does not apply to scalar product.

The vector or cross product of two vectors and is denoted by . is a vector

perpendicular to the plane containing and , the magnitude is given by and

direction is given by right hand rule as explained in Figure 1.5.

Next
 ............................................................................................(1.7)

where is the unit vector given by, .

The following relations hold for vector product.

= i.e., cross product is non commutative ..........(1.8)

i.e., cross product is distributive.......................(1.9)

i.e., cross product is non associative..............(1.10)

Scalar and vector triple product :

Scalar triple product .................................(1.11)

Vector triple product ...................................(1.12)

Co-ordinate Systems

In order to describe the spatial variations of the quantities, we require using appropriate co-
ordinate system. A point or vector can be represented in a curvilinear coordinate system
that may be orthogonal or non-orthogonal .

An orthogonal system is one in which the co-ordinates are mutually perpendicular. Non-
orthogonal co-ordinate systems are also possible, but their usage is very limited in practice .

Let u = constant, v = constant and w = constant represent surfaces in a coordinate system,

the surfaces may be curved surfaces in general. Furthur, let , and be the unit
vectors in the three coordinate directions(base vectors). In a general right handed orthogonal
curvilinear systems, the vectors satisfy the following relations :

.....................................(1.13)

These equations are not independent and specification of one will automatically imply the
other two. Furthermore, the following relations hold
 ................(1.14)

A vector can be represented as sum of its orthogonal components,

...................(1.15)
In general u, v and w may not represent length. We multiply u, v and w by conversion factors
h1,h2 and h3 respectively to convert differential changes du, dv and dw to corresponding
changes in length dl1, dl2, and dl3. Therefore

...............(1.16)

In the same manner, differential volume dv can be written as and

differential area ds1 normal to is given by, . In the same manner,

differential areas normal to unit vectors and can be defined.

In the following sections we discuss three most commonly used orthogonal co-
ordinate systems, viz:

1. Cartesian (or rectangular) co-ordinate system

2. Cylindrical co-ordinate system

3. Spherical polar co-ordinate system

Cartesian Co-ordinate System :

In Cartesian co-ordinate system, we have, (u,v,w) = (x,y,z). A point P(x0, y0, z0) in Cartesian co-
ordinate system is represented as intersection of three planes x = x0, y = y0 and z = z0. The
unit vectors satisfies the following relation:
In cartesian co-ordinate system, a vector can be written as . The
dot and cross product of two vectors and can be written as follows:

.................(1.19)

....................(1.20)

Since x, y and z all represent lengths, h1= h2= h3=1. The differential length, area and volume
are defined respectively as
 ................(1.21)

.................................(1.22)

Cylindrical Co-ordinate System :

For cylindrical coordinate systems we have a point is

determined as the point of intersection of a cylindrical surface r = r0, half plane containing the
z-axis and making an angle ; with the xz plane and a plane parallel to xy plane located
at z=z0 as shown in figure 7 on next page.

In cylindrical coordinate system, the unit vectors satisfy the following relations

A vector can be written as , ...........................(1.24)

The differential length is defined as,

......................(1.25)

.....................(1.23)
Transformation between Cartesian and Cylindrical coordinates:

Let us consider is to be expressed in Cartesian co-ordinate as

. In doing so we note that

and it applies for other components as well.
These relations can be put conveniently in the matrix form as:

.....................(1.30)

themselves may be functions of as:

............................(1.31)

The inverse relationships are: ........................(1.32)

 Fig 1.10: Spherical Polar Coordinate System

Thus we see that a vector in one coordinate system is transformed to another coordinate
system through two-step process: Finding the component vectors and then variable
transformation.

Spherical Polar Coordinates:

For spherical polar coordinate system, we have, . A point is

represented as the intersection of

(i) Spherical surface r=r0

(ii) Conical surface ,and

(iii) half plane containing z-axis making angle with the xz plane as shown in the figure
1.10.

The unit vectors satisfy the following relationships: .....................................(1.33)

The orientation of the unit vectors are shown in the figure 1.11.
A vector in spherical polar co-ordinates is written as : and

For spherical polar coordinate system we have h1=1, h2= r and h3= .
 Fig 1.12(b) : Exploded view

With reference to the Figure 1.12, the elemental areas are:

.......................(1.34)

and elementary volume is given by

........................(1.35)

Coordinate transformation between rectangular and spherical polar:

With reference to the figure 1.13 ,we can write the following equations:
 ........................................................(1.36)

Given a vector in the spherical polar coordinate system, its

component in the cartesian coordinate system can be found out as follows:

.................................(1.37)
Similarly,

.................................(1.38a)

.................................(1.38b)

The above equation can be put in a compact form:

.................................(1.39)

The components themselves will be functions of . are

related to x,y and z as:

....................(1.40)

and conversely,

.......................................(1.41a)

.................................(1.41b)

.....................................................(1.41c)

Using the variable transformation listed above, the vector components, which are functions
of variables of one coordinate system, can be transformed to functions of variables of other
coordinate system and a total transformation can be done.

Line, surface and volume integrals

In electromagnetic theory, we come across integrals, which contain vector functions. Some
representative integrals are listed below:

In the above integrals, and respectively represent vector and scalar function of space
coordinates. C,S and V represent path, surface and volume of integration. All these integrals
are evaluated using extension of the usual one-dimensional integral as the limit of a sum,
i.e., if a function f(x) is defined over arrange a to b of values of x, then the integral is given by

.................................(1.42)

where the interval (a,b) is subdivided into n continuous interval of lengths .

Line Integral: Line integral is the dot product of a vector with a specified C; in other
words it is the integral of the tangential component along the curve C.

As shown in the figure 1.14, given a vector around C, we define the integral

as the line integral of E along the curve C.

If the path of integration is a closed path as shown in the figure the line integral becomes a

closed line integral and is called the circulation of around C and denoted as as
shown in the figure 1.15.
 Fig 1.15: Closed Line Integral

Surface Integral :

Given a vector field , continuous in a region containing the smooth surface S, we define

the surface integral or the flux of through S as as

surface integral over surface S.

Fig 1.16 : Surface Integral

If the surface integral is carried out over a closed surface, then we write

Volume Integrals:
We define or as the volume integral of the scalar function f(function of spatial

coordinates) over the volume V. Evaluation of integral of the form can be carried out
as a sum of three scalar volume integrals, where each scalar volume integral is a component
of the vector

The Del Operator :

The vector differential operator was introduced by Sir W. R. Hamilton and later on
developed by P. G. Tait.

Mathematically the vector differential operator can be written in the general form as:

.................................(1.43)

In Cartesian coordinates:

................................................(1.44)

In cylindrical coordinates:

...........................................(1.45)

and in spherical polar coordinates:

.................................(1.46)

Gradient of a Scalar function:

Let us consider a scalar field V(u,v,w) , a function of space coordinates.

Gradient of the scalar field V is a vector that represents both the magnitude and direction of
the maximum space rate of increase of this scalar field V.
 Fig 1.17 : Gradient of a scalar function

As shown in figure 1.17, let us consider two surfaces S1and S2 where the function V has
constant magnitude and the magnitude differs by a small amount dV. Now as one moves
from S1 to S2, the magnitude of spatial rate of change of V i.e. dV/dl depends on the direction
of elementary path length dl, the maximum occurs when one traverses from S1to S2along a
path normal to the surfaces as in this case the distance is minimum.

By our definition of gradient we can write:

.......................................................................
(1.47)

since which represents the distance along the normal is the shortest distance between
the two surfaces.

For a general curvilinear coordinate system

...................
.(1.48)

Further we can write

......................................................
(1.49)

Hence,

....................................(1.50)
Also we can write,

............................(1.51)

By comparison we can write,

....................................................................(1.52)

Hence for the Cartesian, cylindrical and spherical polar coordinate system, the expressions
for gradient can be written as:
In Cartesian coordinates:

...................................................................................(1.53)

In cylindrical coordinates:

..................................................................(1.54)

and in spherical polar coordinates:

..........................................................(1.55)

The following relationships hold for gradient operator.

...............................................................................(1.56)

where U and V are scalar functions and n is an integer.

It may further be noted that since magnitude of depends on the direction of dl,
it is called the directional derivative. If is called the scalar potential function of
the vector function .

Divergence of a Vector Field:

In study of vector fields, directed line segments, also called flux lines or streamlines,
represent field variations graphically. The intensity of the field is proportional to the density of
lines. For example, the number of flux lines passing through a unit surface S normal to the
vector measures the vector field strength.

Fig 1.18: Flux Lines

We have already defined flux of a vector field as

....................................................(1.57)

For a volume enclosed by a surface,

.........................................................................................(1.58)

We define the divergence of a vector field at a point P as the net outward flux from a
volume enclosing P, as the volume shrinks to zero.

.................................................................(1.59)

Here is the volume that encloses P and S is the corresponding closed surface.
 Fig 1.19: Evaluation of divergence in curvilinear coordinate

Let us consider a differential volume centered on point P(u,v,w) in a vector field . The flux
through an elementary area normal to u is given by ,

........................................(1.60)

Net outward flux along u can be calculated considering the two elementary surfaces perpendicular to u .

.......................................(1.61)
Considering the contribution from all six surfaces that enclose the volume, we can write

.......................................(1.62)

Hence for the Cartesian, cylindrical and spherical polar coordinate system, the expressions for divergence can be
written as:

In Cartesian coordinates:

................................(1.63)

In cylindrical coordinates:
 ....................................................................(1.64)

and in spherical polar coordinates:

......................................(1.65)

In connection with the divergence of a vector field, the following can be noted

 Divergence of a vector field gives a scalar.

 ..............................................................................(1.66)

Divergence theorem :
Divergence theorem states that the volume integral of the divergence of vector field is equal
to the net outward flux of the vector through the closed surface that bounds the volume.

Mathematically,

Proof:

Let us consider a volume V enclosed by a surface S . Let us subdivide the volume in large
number of cells. Let the kth cell has a volume and the corresponding surface is denoted
by Sk. Interior to the volume, cells have common surfaces. Outward flux through these
common surfaces from one cell becomes the inward flux for the neighboring cells. Therefore
when the total flux from these cells are considered, we actually get the net outward flux
through the surface surrounding the volume. Hence we can write:

......................................(1.67)

In the limit, that is when and the right hand of the expression can be

written as .

Hence we get , which is the divergence theorem.

Curl of a vector field:

We have defined the circulation of a vector field A around a closed path as .

Curl of a vector field is a measure of the vector field's tendency to rotate about a
point. Curl , also written as is defined as a vector whose magnitude is
maximum of the net circulation per unit area when the area tends to zero and its
direction is the normal direction to the area when the area is oriented in such a
way so as to make the circulation maximum.

Therefore, we can write:

......................................(1.68)

To derive the expression for curl in generalized curvilinear coordinate system, we first

compute and to do so let us consider the figure 1.20 :

Fig 1.20: Curl of a Vector

C1 represents the boundary of , then we can write

......................................(1.69)

The integrals on the RHS can be evaluated as follows:

.................................(1.70)

................................................(1.71)

The negative sign is because of the fact that the direction of traversal reverses. Similarly,

..................................................(1.72)

............................................................................(1.73)
Adding the contribution from all components, we can write:

........................................................................
(1.74)

Therefore, ........................(1.75)

In the same manner if we compute for and we can write,

.......(1.76)

This can be written as,

......................................................(1.77)

In Cartesian coordinates: .......................................(1.78)

In Cylindrical coordinates, ....................................(1.79)

In Spherical polar coordinates, ..............(1.80)

Curl operation exhibits the following properties:

 ..............(1.81)

Stoke's theorem :

It states that the circulation of a vector field around a closed path is equal to the integral of
over the surface bounded by this path. It may be noted that this equality holds
provided and are continuous on the surface.

i.e,

..............(1.82)

Proof:Let us consider an area S that is subdivided into large number of cells as shown in the
figure 1.21.

Fig 1.21: Stokes theorem

Let kthcell has surface area and is bounded path Lk while the total area is
bounded by path L. As seen from the figure that if we evaluate the sum of the line
integrals around the elementary areas, there is cancellation along every interior
path and we are left the line integral along path L. Therefore we can write,
 ..............(1.83)

As 0

. .............(1.84)

which is the stoke's theorem.

ASSIGNMENT PROBLEMS

1. In the Cartesian coordinate system; verify the following relations for a scalar function
and a vector function

a.

b.

c.

2. An electric field expressed in spherical polar coordinates is given by .

Determine and at a point .

3. Evaluate over the surface of a sphere of radius centered at the

origin.

4. Find the divergence of the radial vector field given by .

5. A vector function is defined by . Find around the contour

shown in the figure P1.3 . Evaluate over the shaded area and verify that
Figure P1.3