PTC04 UI

User Interface PTC-04 Programmer

U S E R IN TE RFA C E
P TC - 0 4 P ROG RA M ME R

Introduction
This document describes the User Interface of the PTC-04 programmer. The PTC-04 User Interface
groups all tooling of the PTC-04.

The UI can be installed together with MPT and the PTC-04 PSF but it is not mandatory for using the
product specific function library used to program the MLX product.

For information about the different software layers, please refer to the document:
Get_Started_With_PTC04.pdf

Contents:

Introduction .................................................................................................................................................................. 1

User Interface PTC-04 ................................................................................................................................................. 2

Calibrator................................................................................................................................................................... 2
Firmware Commander ............................................................................................................................................... 2
Upload firmware ........................................................................................................................................................ 3
Test Program.............................................................................................................................................................. 4
Configuration ............................................................................................................................................................. 5
Hardware ID ........................................................................................................................................................... 5
Firmware ID ........................................................................................................................................................... 6

Disclaimer ..................................................................................................................................................................... 7

User Interface PTC-04 Programmer Page 1 of 7 December 2013

UI Rev. 1.34 or higher
 PTC04 UI
User Interface PTC-04 Programmer

Launch the MPT

To launch the Melexis Programmable Toolbox, go to
StartProgramsMelexisMelexis Programmable Toolbox
and select the Melexis Programmable Toolbox.

To open the User Interface of the PTC-04, double click on the

text “PTC-04” listed under the UI modules in the workspace
on the left side of the Melexis Programmable Toolbox.
Once the UI is active the text becomes bold.

You can also start the PTC04 UI directly trough

StartProgramsMelexisMelexis Programmable Toolbox
and select PTC04 UI.

For information about the MPT, please refer to the document:

MPT.pdf

Figure 1: MPT Workspace upper left side.

User Interface PTC-04

There are five tools available for the user:
 Calibrate
 Upload firmware
 Firmware commander
 Test Programmer
 Configuration

Figure 2: PTC-04 User Interface.

Calibrator
The Calibrator is a tool that allows our customer to check the calibration of their programmer. The tool will
verify the deviation on measurements and supplies. Optional it allows the user to calibrate these
parameters. This last item requires a good calibrated reference voltmeter.

For information on how to use this tool, we refer to the documentation of the calibrator tool:
User_Manuel_Calibration_Software_PTC04.pdf

Firmware Commander
The firmware commander is a tool that is internally used by Melexis. This tool provides you an interface to
play with basic commands like setting the power supplies and performing measurements. Basically it is an
Engineering tool.

User Interface PTC-04 Programmer Page 2 of 7 December 2013

UI Rev. 1.34 or higher
 PTC04 UI
User Interface PTC-04 Programmer

Upload firmware
The firmware loader is needed in order to upload
new or other firmware into the PTC-04 programmer.

For most MLX products there is a specific firmware,

PSF and UI for the PTC-04 programmer. Therefore
it is important to have the correct firmware loaded in
the PTC-04 programmer.

At start-up the PSF layer checks the ID and revision

of the firmware that is loaded in the PTC-04. If the
firmware doesn’t support the MLX product of the
PSF, the PSF layer returns an error message.

Figure 3: PTC-04 User Interface.

In such a case you have to upload the correct firmware:

 To start, press the button “Upload

Firmware” on the PTC-04 User
Interface.
 Select the firmware needed for your
MLX product.

The firmware filename is called

ptc04_mlx*****_firmware.hex or
FIR******AAMLX.hex.

The marks ***** stand for the MLX

product name.

For ex.: ptc04_mlx90251_firmware.hex or

FIR090264AAMLX.hex.
Figure 4: Open file.

Ones the file is opened, the

firmware is loaded in to the
PTC-04 programmer.

Figure 5: Loading firmware.

 If the software requests to reset the PTC-04, please press the small button next to the RS232
connector.

Afterwards the software

verifies if the upload was done
correctly.

Figure 6: Verifying firmware.

The firmware ID and revision can also be checked with the Configuration tool. See Chapter Configuration.

User Interface PTC-04 Programmer Page 3 of 7 December 2013

UI Rev. 1.34 or higher
 PTC04 UI
User Interface PTC-04 Programmer

Test Program
The test program is made to perform a quick check of the hardware. It allows the user to verify if there is
any hardware damage on his PTC-04 programmer. The test checks the functionality of the fixed power
supplies, programmable power supplies, the internal voltmeter, etc…

 To start, press the button “Test programmer” on the PTC-04 User Interface.
 Press the “Start” button to run the hardware check.

Figure 7: Test Program. Result = Pass.

In the middle of the window all tests are listed that were performed by the software. On the left, all tests
that passed are listed. The tests that failed are listed on the right.

Figure 8: Test Program. Result = Fail.

User Interface PTC-04 Programmer Page 4 of 7 December 2013

UI Rev. 1.34 or higher
 PTC04 UI
User Interface PTC-04 Programmer

Configuration
The tool configuration is used to check the hardware and firmware ID of the PTC-04 programmer.

Hardware ID
The PTC04 programmer has 2 PCB’s: the Main Board and the Daughter Board. Both boards have a
hardware ID description. The hardware ID is stored in an EEPROM on the board.

The most important part of the hardware ID is the

HW Name and HW Revision. These are used by
the software DLL’s to verify the connected
hardware type.

The EEPROM also contains data on the status of

the programmer like: Last Calibration, Next
Calibration and HW Status.

The HW Status can be used to mark a PTC-04 as

“not to be used”.

Remark 1, 2 etc… can be used to store additional

information on the setup and the usage.

Figure 9: Main Board Description.

On the Main Board and Daughter Board

Description there are three buttons.

 Load
With this button you down load the board
description from the EEPROM.

 Save and Save Defaults

With this button you up load the modified or default
board description in the EEPROM.

Melexis advises not to modify the Main board or

Daughter Board HW description.

If you modify the HW description of the Main Board

or the Daughter Board the software may no longer
recognise the hardware.

Figure 10: Daughter board description.

User Interface PTC-04 Programmer Page 5 of 7 December 2013

UI Rev. 1.34 or higher
 PTC04 UI
User Interface PTC-04 Programmer

Firmware ID
Firmware ID is a tool made to check the name and revision
of the firmware loaded in the PTC-04 programmer.

The firmware contains general functions of the PTC04 and

product specific functions. The product specific commands
are made to communicate with the specific MLX product.

It’s important that the correct firmware is loaded in the

PTC04 programmer. Software ID functions allow higher
layers to check if the firmware can be used for that specific
MLX product.

Figure 11: FW_ID.

 Load
With this button you load the description of the firmware that is currently in the PTC-04 programmer.

The Fuses tool is internally used by Melexis. This tool is for info purpose only.

User Interface PTC-04 Programmer Page 6 of 7 December 2013

UI Rev. 1.34 or higher
 PTC04 UI
User Interface PTC-04 Programmer

Disclaimer
Devices sold by Melexis are covered by the warranty and patent indemnification provisions appearing in
its Term of Sale. Melexis makes no warranty, express, statutory, implied, or by description regarding the
information set forth herein or regarding the freedom of the described devices from patent infringement.
Melexis reserves the right to change specifications and prices at any time and without notice. Therefore,
prior to designing this product into a system, it is necessary to check with Melexis for current information.
This product is intended for use in normal commercial applications. Applications requiring extended
temperature range, unusual environmental requirements, or high reliability applications, such as military,
medical life-support or life-sustaining equipment are specifically not recommended without additional
processing by Melexis for each application.
The information furnished by Melexis is believed to be correct and accurate. However, Melexis shall not
be liable to recipient or any third party for any damages, including but not limited to personal injury,
property damage, loss of profits, loss of use, interrupt of business or indirect, special incidental or
consequential damages, of any kind, in connection with or arising out of the furnishing, performance or
use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow
out of Melexis’ rendering of technical or other services.
© 2013 Melexis NV. All rights reserved.

For the latest version of this document, go to our website at

www.melexis.com

Or for additional information contact Melexis Direct:

Europe, Africa, Asia: America:

Phone: +32 13 670 495 Phone: +1 603 223 2362
E-mail: [email protected] E-mail: [email protected]

ISO/TS 16949 and ISO14001 Certified

User Interface PTC-04 Programmer Page 7 of 7 December 2013

UI Rev. 1.34 or higher