Scribd Logo
Upload

Welcome to Scribd!

  • 657 views

    Mitsubishi Meldas 2M Memoria Format

    Uploaded by

    angel
    This document provides 4 methods for erasing or blanking the data on an Mitsubishi FX27 or FX727 memory board: 1. Enter specific codes through the control's diagnostic mode to blank the board while it is installed in the control. 2. Flip a dip switch while powering on/off the control to blank the board while installed. 3. Remove the board from the control, discharge its capacitor, and reinstall to blank the data. 4. Connect a PC to the control's serial port, enter a code through communication software, then reinstall the board to blank it offline.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Mitsubishi Meldas 2M Memoria Format

    Uploaded by

    angel
    657 views4 pages
    This document provides 4 methods for erasing or blanking the data on an Mitsubishi FX27 or FX727 memory board: 1. Enter specific codes through the control's diagnostic mode to blank the board while it is installed in the control. 2. Flip a dip switch while powering on/off the control to blank the board while installed. 3. Remove the board from the control, discharge its capacitor, and reinstall to blank the data. 4. Connect a PC to the control's serial port, enter a code through communication software, then reinstall the board to blank it offline.

    Original Description:

    Format memmory clear error led

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides 4 methods for erasing or blanking the data on an Mitsubishi FX27 or FX727 memory board: 1. Enter specific codes through the control's diagnostic mode to blank the board while it is installed in the control. 2. Flip a dip switch while powering on/off the control to blank the board while installed. 3. Remove the board from the control, discharge its capacitor, and reinstall to blank the data. 4. Connect a PC to the control's serial port, enter a code through communication software, then reinstall the board to blank it offline.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    657 views4 pages

    Mitsubishi Meldas 2M Memoria Format

    Uploaded by

    angel
    This document provides 4 methods for erasing or blanking the data on an Mitsubishi FX27 or FX727 memory board: 1. Enter specific codes through the control's diagnostic mode to blank the board while it is installed in the control. 2. Flip a dip switch while powering on/off the control to blank the board while installed. 3. Remove the board from the control, discharge its capacitor, and reinstall to blank the data. 4. Connect a PC to the control's serial port, enter a code through communication software, then reinstall the board to blank it offline.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 4

    MELDAS FX Series

    How To Blank [erase] FX27 Or FX727

    USA-E99041 -003*

    MITSUBISHI ELECTRIC AUTOMATION

    USA
    List of Past Revisions

    Suffix Date of Revision Detail


    * 5/20/98 First edition created
    How to Erase (Blank) FX27/727

    Why Erase FX27 / 727

    FX27 /727 is a memory board. It has a battery back-up and holds ALL parameters and
    machine data. If control locks-up or starts acting differently than what it is supposed to,
    the data in this board might be scrambled. Power surge or lightning strike can cause the
    same problem also. In this situation, FX27 /727 needs to be blanked.

    Erasing (Blanking) FX27 / 727

    Following are 4 methods one can use depending upon the circumstances.

    Method 1 (For Non-Mazak: For example OKK, MHI etc.)

    1. Turn ON control
    2. Press DIAG then NEXT 4 times

    76543210
    3. Enter (1000) ( 1 ) (M2), INPUT twice
    4. Press GRAF, Enter CPU(L) INPUT
    5. Power OFF/ON
    6. Confirm 0’s in parameter values
    7. Input parameters
    8. Power OFF/ON

    Method 2 (Mazatrol: T2, T3 with sys s/w Ver B4 or higher. It will not be effective for
    earlier versions)

    1. With control power OFF, flip dip SW 3 over on FX01/701


    2. Power ON for about 30 seconds
    3. Power OFF, flip dip SW 3 back to original position
    4. Power ON
    5. Confirm 0’s in parameter values
    6. Reload parameters. Hand type if needed.
    7. Power OFF/ON
    Method 3 (Mazatrol, T2, T3 )

    1. With power OFF, take FX27/727 out of the control.


    2. Remove battery jumpers (2 jumpers next to the battery).
    3. Put a low resistance resistor across the super capacitor to discharge it. Make sure it is
    drained completely.
    4. Put battery jumpers back on the board. Put board back in the control.
    5. Power ON and confirm 0’s in parameter values
    6. Input parameters
    7. Power OFF/ON

    Note: a. This procedure will not put 0’s in parameter fields instead there will be “ * ”
    and scrambled values.
    b. Using this procedure on M1 control can simulate a locked operation panel/
    Control. Hold ATC button, move through parameters screen and enter a few
    parameters. Power Off/On. Enter the rest of the parameters. Format memory
    using the –9999 or 7777 procedure. If everything fails, use Method 4.

    Method 4 (Offline method, use when all of above fail)

    1. With control power OFF, connect the PC cable to the RS232 slot on FX01/701 SCN
    1
    2. Flip over dip SW 8 on the FX01/701
    3. Start communication program (preferably ProComm plus) on the PC
    4. Set communication parameters on PC as follows:
    (for ProComm: Press ALT P, change as following, and save before proceeding)

    Baud Rate: 4800


    Parity: None
    Data Bits: 8
    Stop Bit: 1
    Port: Direct connection

    5. Power ON the control. There should be a message display on the PC screen:


    “MELDAS MONITOR V3.0”
    6. Type in capital letters FC000:0,FFFF,00 and then hit ENTER
    7. FX27/727 is now blank.
    8. Flip dip SW 8 back to its original position.
    9. Power OFF/ON the control.
    10. Confirm 0’s in parameters and reload the parameters.

    You might also like