Scribd
Upload
18K views4 pages

Tolerance Table

This document provides diameter limits for various shaft and hole fits across different diameter sizes ranging from 1 to 500. It specifies limits for basic holes, running fits, slide fits, transition fits, push fits, wring fits, and interference fits. The limits are expressed as allowances or interference values for each fit type based on the shaft or hole diameter.

Uploaded by

moganna73
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
18K views4 pages

Tolerance Table

This document provides diameter limits for various shaft and hole fits across different diameter sizes ranging from 1 to 500. It specifies limits for basic holes, running fits, slide fits, transition fits, push fits, wring fits, and interference fits. The limits are expressed as allowances or interference values for each fit type based on the shaft or hole diameter.

Uploaded by

moganna73
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Limits and Fits -1

System Symbol Diameter limit


Basic Hole and Over 1 3 6 10 18 30 50 80 120 180 250 315 400
grade Upto 3 6 10 18 30 50 80 120 180 250 315 400 500
With large min. d11 -20 -30 -40 -50 -65 -80 -100 -120 -145 -170 -190 -210 -230
clearance -80 -105 -130 -160 -195 -240 -290 -340 -395 -460 -510 -570 -630
e7 -14 -20 -25 -32 -40 -50 -60 -72 -85 -100 -110 -125 -135
Running fit-shafts

With medium -24 -32 -40 -50 -61 -75 -90 -107 -125 -146 -162 -182 -198
min. clearance e8 -14 -20 -25 -32 -40 -50 -60 -72 -85 -100 -110 -125 -135
-28 -38 -47 -59 -73 -89 -106 -126 -148 -172 -191 -214 -232
With small f7 -6 -10 -13 -16 -20 -25 -30 -36 -43 -50 -56 -62 -68
minimum -16 -22 -28 -34 -41 -50 -60 -71 -83 -96 -108 -119 -131
clearance f8 -6 -10 -13 -16 -20 -25 -30 -36 -43 -50 -56 -62 -68
-20 -28 -35 -43 -53 -64 -76 -90 -106 -122 -137 -151 -165
With smallest g5 -2 -4 -5 -6 -7 -9 -10 -12 -14 -15 -17 -18 -20
minimum -6 -9 -11 -14 -16 -20 -23 -27 -32 -35 -40 -43 -47
clearance g6 -2 -4 -5 -6 -7 -9 -10 -12 -14 -15 -17 -18 -20
-8 -12 -14 -17 -20 -25 -29 -34 -39 -44 -49 -54 -60
h5 0 0 0 0 0 0 0 0 0 0 0 0 0
-4 -5 -6 -8 -9 -11 -13 -15 -18 -20 -23 -25 -27
h6 0 0 0 0 0 0 0 0 0 0 0 0 0
Slide fit

-6 -8 -9 -11 -13 -16 -19 -22 -25 -29 -32 -36 -40
h8 0 0 0 0 0 0 0 0 0 0 0 0 0
-14 -18 -22 -27 -33 -39 -46 -54 -63 -72 -81 -89 -97
h9 0 0 0 0 0 0 0 0 0 0 0 0 0
-25 -30 -36 -43 -52 -62 -74 -87 -100 -115 -130 -140 -155
h11 0 0 0 0 0 0 0 0 0 0 0 0 0
Transition fit-shafts

-60 -75 -90 -110 -130 -160 -190 -220 -250 -290 -320 -360 -400
j5 +2 +3 +4 +5 +5 +6 +6 +6 +7 +7 +7 +7 +7
Push

Transition

-2 -2 -2 -3 -4 -5 -7 -9 -11 -13 -16 -18 -20


fit

-shafts

j6 +4 +6 +7 +8 +9 +11 +12 +13 +14 +16 +16 +18 +20


Fit

-2 -2 -2 -3 -4 -5 -7 -9 -11 -13 -16 -18 -20


k5 +4 +6 +7 +9 +11 +13 +15 +18 +21 +24 +27 +29 +32
Wring

0 +1 +1 +1 +2 +2 +2 +3 +3 +4 +4 +4 +5
fit

k6 +6 +9 +10 +12 +15 +18 +21 +25 +28 +33 +36 +40 +45
0 +1 +1 +1 +2 +2 +2 +3 +3 +4 +4 +4 +5
Secure
m5 +6 +9 +12 +15 +17 +20 +24 +28 +33 +37 +43 +46 +50
against +2 +4 +6 +7 +8 +9 +11 +13 +15 +17 +20 +21 +23
turning
Tight fit

m6 +8 +12 +15 +18 +21 +25 +30 +35 +40 +46 +52 +57 +63
+2 +4 +6 +7 +8 +9 +11 +13 +15 +17 +20 +21 +23
n5 +8 +13 +16 +20 +24 +28 +33 +38 +45 +51 +57 +62 +67
+4 +8 +10 +12 +15 +17 +20 +23 +27 +31 +34 +37 +40
n6 +10 +16 +19 +23 +28 +33 +39 +45 +52 +60 +66 +73 +80
+4 +8 +10 +12 +15 +17 +20 +23 +27 +31 +34 +37 +40
Interference fit

+12 +20 +24 +29 +35 +42 +51 +59 +68 +79 +88 +98 +108
p6 +6 +12 +15 +18 +22 +26 +32 +37 +43 +50 +56 +62 +68

r6 +16 +23 +28 +34 +41 +50 _ _ _ _ _ _ _


+10 +15 +19 +23 +28 +34
s6 +20 +27 +32 +39 +48 +59 _ _ _ _ _ _ _
+14 +19 +23 +28 +35 +43
H6 +6 +8 +9 +11 +13 +16 +19 +22 +25 +29 +32 +36 +40
0 0 0 0 0 0 0 0 0 0 0 0 0
H7 +10 +12 +15 +18 +21 +25 +30 +35 +40 +46 +52 +57 +63
0 0 0 0 0 0 0 0 0 0 0 0 0
Basic hole H8 +14 +18 +22 +27 +33 +39 +46 +54 +63 +72 +81 +89 +97
0 0 0 0 0 0 0 0 0 0 0 0 0
H9 +25 +30 +36 +43 +52 +62 +74 +87 +100 +115 +130 +140 +155
0 0 0 0 0 0 0 0 0 0 0 0 0
H11 +60 +75 +90 +110 +130 +160 +190 +220 +250 +290 +320 +360 +400
0 0 0 0 0 0 0 0 0 0 0 0 0
Limits and Fits -2
System Symbol Diameter limit
and Over 1 3 6 10 18 30 50 80 120 180 250 315 400
Basic Shaft
grade Upto 3 6 10 18 30 50 80 120 180 250 315 400 500
With large min. D10 +60 +78 +98 +120 +149 +180 +220 +260 +305 +355 +400 +440 +480
clearance +20 +30 +40 +50 +65 +80 +100 +120 +145 +170 +190 +210 +230
With medium E7 +24 +32 +40 +50 +61 +75 +90 +107 +125 +146 +162 +182 +198
Running fit –holes

min. +14 +20 +25 +32 +40 +50 +60 +72 +85 +100 +110 +125 +135
clearance E8 +28 +38 +47 +59 +73 +89 +106 +126 +148 +172 +191 +214 +232
+14 +20 +25 +32 +40 +50 +60 +72 +85 +100 +110 +125 +135
With small F7 +16 +22 +28 +34 +41 +50 +60 +71 +83 +95 +108 +119 +131
Minimum +6 +10 +13 +16 +20 +25 +30 +36 +43 +50 +56 +62 +68
clearance F8 +20 +28 +35 +43 +53 +64 +76 +90 +106 +122 +137 +151 +165
+6 +10 +13 +16 +20 +25 +30 +36 +43 +50 +56 +62 +68
With smallest G7 +12 +16 +20 +24 +28 +34 +40 +47 +54 +61 +69 +75 +83
Min. clearance +2 +4 +5 +6 +7 +9 +10 +12 +14 +15 +17 +18 +20
H6 +6 +8 +9 +11 +13 +16 +19 +22 +25 +29 +32 +36 +40
0 0 0 0 0 0 0 0 0 0 0 0 0
H7 +10 +12 +15 +18 +21 +25 +30 +35 +40 +46 +52 +57 +63
0 0 0 0 0 0 0 0 0 0 0 0 0
Slide fit

H8 +14 +18 +22 +27 +33 +39 +46 +54 +63 +72 +81 +89 +97
0 0 0 0 0 0 0 0 0 0 0 0 0
H9 +25 +30 +36 +43 +52 +62 +74 +87 +100 +115 +130 +140 +155
0 0 0 0 0 0 0 0 0 0 0 0 0
H11 +60 +75 +90 +110 +130 +160 +190 +220 +250 +290 +320 +360 +400
Transition fit-holes

0 0 0 0 0 0 0 0 0 0 0 0 0
J6 +2 +5 +5 +6 +8 +10 +13 +16 +18 +22 +25 +29 +33
Push

-4 -3 -4 -5 -5 -6 -6 -6 -7 -7 -7 -7 -7
fit

J7 +4 +6 +8 +10 +12 +14 +18 +22 +26 +30 +36 +39 +43
-6 -6 -7 -8 -9 -11 -12 -13 -14 -16 -16 -18 -20
K6 0 +2 +2 +2 +2 +3 +4 +4 +4 +5 +5 +7 +8
Wring

-6 -6 -7 -9 -11 -13 -15 -18 -21 -24 -27 -29 -32


fit

K7 0 +3 +5 +6 +6 +7 +9 +10 +12 +13 +16 +17 +18


Secure -10 -9 -10 -12 -15 -18 -21 -25 -28 -33 -36 -40 -45
Against M6 -2 -1 -3 -4 -4 -4 -5 -6 -8 -8 -9 -10 -10
turning -8 -9 -12 -15 -17 -20 -24 -28 -33 -37 -41 -46 -50
M7 -2 0 0 0 0 0 0 0 0 0 0 0 0
Tight fit

-12 -12 -15 -18 -21 -25 -30 -35 -40 -46 -52 -57 -63
N6 -4 -5 -7 -9 -11 -12 -14 -16 -20 -22 -25 -26 -27
-10 -13 -16 -20 -24 -28 -33 -38 -45 -51 -57 -62 -67
N7 -4 -4 -4 -5 -7 -8 -9 -10 -12 -14 -14 -16 -17
-14 -16 -19 -23 -28 -33 -39 -45 -52 -60 -66 -73 -80
P7 -6 -8 -9 -11 -14 -17 -21 -24 -28 -33 -36 -41 -45
Interference -16 -20 -24 -29 -35 -42 -51 -59 -68 -79 -88 -98 -108
P9 -6 -12 -15 -18 -22 -26 -32 -37 -43 -50 -56 -62 -68
Fit-holes -31 -42 -51 -61 -74 -88 -108 -124 -143 -165 -186 -202 -223
h5 0 0 0 0 0 0 0 0 0 0 0 0 0
-4 -5 -6 -8 -9 -11 -13 -15 -18 -20 -23 -25 -27
h6 0 0 0 0 0 0 0 0 0 0 0 0 0
-6 -8 -9 -11 -13 -16 -19 -22 -25 -29 -32 -36 -40
Basic Shaft h8 0 0 0 0 0 0 0 0 0 0 0 0 0
-14 -18 -22 -27 -33 -39 -46 -54 -63 -72 -81 -89 -97
h9 0 0 0 0 0 0 0 0 0 0 0 0 0
-25 -30 -36 -43 -52 -62 -74 -87 -100 -115 -130 -140 -155
h11 0 0 0 0 0 0 0 0 0 0 0 0 0
-60 -75 -90 -110 -130 -160 -190 -220 -250 -290 -320 -360 -400
Limits and Fits-3 [Typical Applications]

Typical *Symbol Diameter limit


Applications and Over 1 3 6 10 18 30 50 80 120 180 250 315 400
grade Upto 3 6 10 18 30 50 80 120 180 250 315 400 500
Major dia. of a11 -270 -270 -280 -290 -300
-330 -345 -370 -400 -430
external splines
Width of T-Nuts a13 -270 -270 -280 -290 -300
-410 -450 -500 -560 -630
f6 -6 -10 -13 -16 -20 -25 -30 -36 -43 -50 -56 -62 -68
-12 -18 -22 -27 -33 -41 -49 -58 -68 -79 -88 -98 -108
h7 0 0 0 0 0 0 0 0 0 0 0 0 0
-10 -12 -15 -18 -21 -25 -30 -35 -40 -46 -52 -57 -63
Socket head dia. h12 0 0 0 0 0 0 0 0 0 0 0 0 0
-100 -120 -150 -180 -210 -250 -300 -350 -400 -460 -520 -570 -630
Socket head h13 0 0 0 0 0 0 0 0 0 0 0 0 0
-140 -180 -220 -270 -330 -390 -460 -540 -630 -720 -810 -890 -970
height
h14 0 0 0 0 0 0 0 0 0 0 0 0 0
-250 -300 -360 -430 -520 -620 -740 -870 -1000 -1150 -1300 -1400 -1550
Slotted and
h15 0 0 0 0 0 0 0 0 0 0 0 0 0
Castle nut -400 -480 -580 -700 -840 -1000 -1200 -1400 -1600 -1850 -2100 -2300 -2500
dimensions h16 0 0 0 0 0 0 0 0 0 0 0 0 0
-600 -750 -900 -1100 -1300 -1600 -1900 -2200 -2500 -2900 -3200 -3600 -4000
js9 +12.5 +15 +18 +21.5 +26 +31 +37 +43.5 +50 +57.5 +65 +70 +77.5
-12.5 -15 -18 -21.5 -26 -31 -37 -43.5 -50 -57.5 -65 -70 -77.5
Symmetrical
js14 +125 +150 +180 +215 +260 +310 +370 +435 +500 +575 +650 +700 +775
length -125 -150 -180 -215 -260 -310 -370 -435 -500 -575 -650 -700 -775
tolerances js15 +200 +240 +290 +350 +420 +500 +600 +700 +800 +925 +1050 +1150 +1250
-200 -240 -290 -350 -420 -500 -600 -700 -800 -925 -1050 -1150 -1250
Hydraulic A11 +330 +345 +370 +400 +430
+270 +270 +280 +290 +300
fittings
B11 +200 +215 +240 +260 +290
+140 +140 +150 +150 +160
Key-way width in C11 +120 +145 +170 +205 +240
+60 +70 +80 +95 +110
Spacer rings
Width of internal D9 +45 +60 +76 +93 +117 +142 +174 +207 +245 +285 +320 +350 +385
+20 +30 +40 +50 +65 +80 +100 +120 +145 +170 +190 +210 +230
splines
Hexagonal D12 +120 +150 +190 +230 +275 +330 +400 +470 +545 +630 +710 +780 +860
+20 +30 +40 +50 +65 +80 +100 +120 +145 +170 +190 +210 +230
socket width
Circlips H10 +40 +48 +58 +70 +84 +100 +120 +140 +160 +185 +210 +230 +250
0 0 0 0 0 0 0 0 0 0 0 0 0
Counter bore H12 +100 +120 +150 +180 +210 +250 +300 +350 +400 +460 +520 +570 +630
0 0 0 0 0 0 0 0 0 0 0 0 0
diameter
Major diameter of H13 +140 +180 +220 +270 +330 +390 +460 +540 +630 +720 +810 +890 +970
0 0 0 0 0 0 0 0 0 0 0 0 0
internal splines
Key-way width Js9 +12.5 +15 +18 +21.5 +26 +31 +37 +43.5 +50 +57.5 +65 +70 +77.5
-12.5 -15 -18 -21.5 -26 -31 -37 -43.5 -50 -57.5 -65 -70 -77.5
Symmetrical Js14 +125 +150 +180 +215 +260 +310 +370 +435 +500 +575 +650 +700 +775
-125 -150 -180 -215 -260 -310 -370 -435 -500 -575 -650 -700 -775
tolerances in
Js16 +300 +375 +450 +550 +650 +800 +950 +1100 +1250 +1450 +1600 +1800 +2000
slots -300 -375 -450 -550 -650 -800 -950 -1100 -1250 -1450 -1600 -1800 -2000
* NOT TO BE SPECIFIED FOR GENERAL LIMITS AND FITS.

You might also like