Scribd Logo
Upload

Welcome to Scribd!

  • 79 views

    Pages From Iom - 111

    Uploaded by

    Abdul Raheem
    The document provides instructions for installing an external condensate trap and making electrical connections for an HVAC unit. It describes connecting a condensate drain line to the unit and installing an external trap at least 4 inches deep to protect against freeze-up. It warns of electrical shock hazards and outlines that field power wires should be copper and connected at line-side pressure lugs or a disconnect switch in accordance with local codes.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Pages From Iom - 111

    Uploaded by

    Abdul Raheem
    79 views1 page
    The document provides instructions for installing an external condensate trap and making electrical connections for an HVAC unit. It describes connecting a condensate drain line to the unit and installing an external trap at least 4 inches deep to protect against freeze-up. It warns of electrical shock hazards and outlines that field power wires should be copper and connected at line-side pressure lugs or a disconnect switch in accordance with local codes.

    Original Description:

    CDP

    Original Title

    Pages From Iom_111

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides instructions for installing an external condensate trap and making electrical connections for an HVAC unit. It describes connecting a condensate drain line to the unit and installing an external trap at least 4 inches deep to protect against freeze-up. It warns of electrical shock hazards and outlines that field power wires should be copper and connected at line-side pressure lugs or a disconnect switch in accordance with local codes.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    79 views1 page

    Pages From Iom - 111

    Uploaded by

    Abdul Raheem
    The document provides instructions for installing an external condensate trap and making electrical connections for an HVAC unit. It describes connecting a condensate drain line to the unit and installing an external trap at least 4 inches deep to protect against freeze-up. It warns of electrical shock hazards and outlines that field power wires should be copper and connected at line-side pressure lugs or a disconnect switch in accordance with local codes.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    Step 10 — Install External Condensate Trap and Step 11 — Make Electrical Connections

    Line
    The unit has one 19 mm (3/4-in.) condensate drain ! WARNING
    connection on the end of the condensate pan (see Fig. 18).
    See Figs. 1, 2 and 3, item “E”, in the view labeled “BACK ELECTRICAL SHOCK HAZARD
    (HORIZONTAL DISCHARGE W/O ECON)” for the Failure to follow this warning could result in personal
    location of the condensate drain connection. injury or death.
    Do not use gas piping as an electrical ground. Unit
    cabinet must have an uninterrupted, unbroken
    electrical ground to minimize the possibility of
    personal injury if an electrical fault should occur. This
    ground may consist of electrical wire connected to
    unit ground lug in control compartment, or conduit
    approved for electrical ground when installed in
    accordance with local electrical codes or in absence
    of local codes, it is recommended that the U.S.A.
    standard ANSI/NFPA 70, National Electrical Code
    50TC-- D

    (NEC), be followed.
    CONDENSATE
    DRAIN
    CONNECTION NOTE: Field-- supplied wiring shall conform with the
    limitations of minimum 33_C (63_F) rise.
    C10729 Field power wires are connected to the unit at line-- side
    Fig. 18 - Condensate Drain Pan Connection pressure lugs on the terminal block (see Fig. 20 or the
    wiring diagram label for control box component
    The piping for the condensate drain and external trap can arrangement) or at factory-- installed option non-- fused
    be completed after the unit is in place. Hand tighten disconnect switch. Use copper conductors only.
    fittings to the drain pan fitting. Provide adequate support
    for the drain line. Failure to do so can result in damage to BLK

    the drain pan. See Fig. 19. YEL


    BLU

    LOAD
    SIDE
    MINIMUM PITCH
    25 mm (1 in.) PER BASE RAIL
    3m (10 ft.) OF LINE
    LINE
    76 mm SIDE
    (3 in.)
    OPEN MIN
    VENT

    SEE
    DETAIL A
    TO ROOF SEE NOTE
    DRAIN
    L1
    L2
    L3
    ROOF
    CURB DETAIL A
    DRAIN PLUG
    CONTROL BOX
    NOTE: Trap should be deep enough to offset maximum unit static
    C11181
    difference. A 102 mm (4 in.) trap. is recommended
    Fig. 20 - Location of TB1
    C11354
    Fig. 19 - Condensate Drain Piping Details NOTE: Make field power connections directly to line
    connection pressure lugs only.
    All units must have an external trap for condensate
    The unit is factory wired for the voltage shown on the
    drainage. Install a trap at least 102 mm (4-in.) deep and
    nameplate. Refer to unit label diagram for additional
    protect against freeze-up. If drain line is installed
    information.
    downstream from the external trap, pitch the line away from
    the unit at 25 mm in 3 m (1-in. per 10 ft) of run. Do not use
    a pipe size smaller than the unit connection of 19 mm
    (3/4 -in.).

    18

    You might also like