PARTS LIST

FLAT WASHER
ANTENNA .25-20 http://www.motorola.com/canopy
REFLECTOR (3 PLACES) FLANGE NUT Sales Support: 866-515-5825
Technical Support: 888-605-2552 (+1 217 824 9742)
.25-20
CARRIAGE BOLT (3 PLACES)
.25 X 20
(2 PLACES) AZ/EL MOUNT
REFLECTOR ASSEMBLY and INSTALLATION
FLANGE NUT
MAST U BOLT 27 RD REFLECTOR
.25-20 (2 PLACES)
Tools Needed: 7/16 inch wrench or adjustable wrench
CARRIAGE BOLT Flat blade screwdriver or 5/16 inch socket for hose clamps and ground screw
#10 x 1.25" 1/2 inch wrench for U-Bolts - Backhaul only
3/8" wrench for #10 nut

1 2
CANOPY FEED
MODULE TUBE
RADIO SPACER FLANGE NUT Slide Radio into mount as shown.

STAR NUT FLAT WASHER

(4 PLACES)
FLAT WASHER RADIO
.25-20 V-BRACKET
(2 PLACES)
HOSE CLAMP CARRIAGE
(2 PLACES) HEX BOLT BOLT
.25-20 x1.5"
#10 HEX
AZ/EL
RADIO MOUNT NUT
MOUNT

QTY DESCRIPTION BACKHAUL MODULE SUBSCRIBER MODULE REFLECTOR (ONLY)

with REFLECTOR (BHRF) with REFLECTOR (27RD)

1 Radio Mount REFLECTOR

1 Feed Tube
1 Antenna Reflector Place Antenna Reflector on flat surface or table. RADIO MOUNT
Attach AZ/EL Mount to Reflector using Carriage Bolts,
1 AZ/EL Mount Flat Washers, and Flange Nuts. Tighten nuts securely.
1 Mast
RADIO

3 4
2 Hose Clamps
MOUNT
2 Carriage Bolt .25 x 20 Tighten Hose
1 Hex Bolt .25-20 x 1.5" Clamps securely
so the Radio is
3 Flange Nut .25-20 RADIO HOSE
snug to the mount
CLAMPS
3 Flat Washers .25-20 with no gaps at
the lower support
1 Spacer rib.
RADIO
1 Carriage Bolt #10 x 1.25" MOUNT
1 #10 Hex Nut
2 U Bolts 5/16 HOSE CLAMP
ADJUSTMENT
2 V-Bracket SCREW
4 Star Nut Loosen and open hose clamps. Slide clamps through the two HOSE (FACING
openings in the Radio above and below the mount as shown in CLAMP RADIO)
1 Canopy Module Radio
this illustration. Close hose clamps attaching radio to mount.
9/04 ECN9000000 8000973-01
5 6 10 11
Assemble the Feed Tube to the Reflector as To adjust azimuth, move Reflector from side to side
shown with 1/4" Flange Nut, .81" Spacer, while AZ/EL Clamp Hardware is loose. Once azimuth
Flat Washer and 1-1/2" Hex Bolt. Tighten is determined, tighten (2) AZ/EL Clamp Nuts securely.
hardware securely.
ANTENNA 1/4" HEX AZ/EL
REFLECTOR FLANGE NUT MOUNT
CLAMP

AZ/EL MOUNT
SPACER
Place Feed Tube on a solid surface or FLAT MAST
table. The Reflector end of the Feed Tube WASHER
has a large hole on the bottom side. Align
bolt holes and press Reflector Socket 1-1/2" Loosen bolts on AZ/EL Mount Clamp. Slide AZ/EL
completely onto Feed Tube as shown. HEX BOLT Mount with preassembed Reflector over mast.
FEED TUBE Loosely tighten AZ/EL Mount Clamp. AZ/EL
CLAMP
NUTS

7 8 Secure Radio Mount to Feed Tube with #10 x 1-1/4"

Carriage Bolt and #10 Nut. Tighten Nut to snug the
bottom of the tube up to the Mount.
REFLECTOR

#10 x 1-1/4"
CARRIAGE Read indicated elevation at this
BOLT edge of plate. The Beam from

12
the Reflector will be horizontal
when the Mast is vertical and
the plate is set at 4.5 degrees
up-elevation as shown.

Slide assembled
radio and mount
into feed tube as
shown. #10 NUT
ELEVATION
EL
EV

9
EL
EV
AT

AT

-2
ION

0
-10

-2
IO N
0

0
10
20

-10
Install Mast on tower or building. For Backhaul,use provided U-Bolts. For Subscriber Module, use locally
0
approved fasteners (lag bolts, screws, etc.) depending on installation. Adjust Mast to be vertical and plumb. 10
Tighten all hardware securely. Connect Ground Screw to Earth Ground using heavy guage (10AWG) copper 20

VERTICAL & PLUMB

wire. Refer to local or national electrical regulations for exact specifications.

BACKHAUL MOUNT SUBSCRIBER MOUNT ELEVATION

ADJUSTMENT
V-BRACKET 10 AWG NUT (ONE ON
GROUND EACH SIDE)
WIRE
MAST
UP TO GREEN The Elevation is set by rotating the Reflector vertically while the Elevation Adjustment Hardware is loose.
VERTICAL & PLUMB

3.25" O.D. GROUND An elevation scale is located on the side of the AZ/EL Mount. As the Reflector is adjusted, the elevation
PIPE (8.0cm O.D.) SCREW scale depicts the elevation angle. Once the elevation is determined, tighten BOTH Elevation Ajustment Nuts
to secure the required angle.
ALTERNATE
GROUND
U BOLT STAR SCREW HOLE
NUT
LOCALLY APPROVED FASTENERS