FL11 4 Funi PDF

32 LCD TV
chassis FL11.4
SERVICE MANUAL
Contents
TYPE A
32MF301B/F7 MAGNAVOX (Serial No.: DS1, DS2)
LC320EM2 EMERSON (Serial No.: DS1, DS3)
LC320SS2 SYLVANIA (Serial No.: DS1, DS2)
TYPE B
32MF301B/F7 MAGNAVOX (Serial No.: TH1)
LC320SS2 SYLVANIA (Serial No.: TH1)
LC320EM2 EMERSON (Serial No.: TH1)
This service manual contains information of different types of models.

Make sure to refer to the section describing your model.
2011 Funai Electric Co., Ltd.

All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed,
downloaded or stored in any storage medium, in any form or for any purpose without the express prior written
consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto
is strictly prohibited.
Information in this document is subject to change without notice. Funai reserves the right to change the content
herein without the obligation to notify any person or organization of such changes.
with the design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way
without the express written consent of Funai. All other trademarks used herein remain the exclusive property of
their respective owners. Nothing contained in this manual should be construed as granting, by implication or
otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any
other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights
to the fullest extent of the law.
110518
IMPORTANT SAFETY NOTICE
Proper service and repair is important to the safe, reliable operation of all
Funai Equipment. The service procedures recommended by Funai and
described in this service manual are effective methods of performing
service operations. Some of these service special tools should be used
when and as recommended.
It is important to note that this service manual contains various CAUTIONS
and NOTICES which should be carefully read in order to minimize the risk
of personal injury to service personnel. The possibility exists that improper
service methods may damage the equipment. It also is important to
understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE.
Funai could not possibly know, evaluate and advice the service trade of all
conceivable ways in which service might be done or of the possible
hazardous consequences of each way. Consequently, Funai has not
undertaken any such broad evaluation. Accordingly, a servicer who uses a
service procedure or tool which is not recommended by Funai must first
use all precautions thoroughly so that neither his safety nor the safe
operation of the equipment will be jeopardized by the service method
selected.
The LCD panel is manufactured to provide many years of useful life.

Occasionally a few non active pixels may appear as a tiny spec of color.
This is not to be considered a defect in the LCD screen.
TABLE OF CONTENTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Standard Notes for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Cabinet Disassembly Instructions [TYPE A] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
[TYPE B] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Electrical Adjustment Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
How to Initialize the LCD TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Firmware Renewal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
Schematic Diagrams / CBA and Test Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1
Exploded Views [TYPE A]. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1
[TYPE B]. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-2
Parts List [TYPE A] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-1
[TYPE B] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-10
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-1
SPECIFICATIONS
< TUNER / NTSC >
ANT. Input ---------------------- 75 Unbal., F type
Description Condition Unit Nominal Limit
1. AFT Pull-In Range --- MHz 2.3 2.1
TV.ch.4 dB 18 20
2. Synchronizing Sens. CA.ch.31 dB 18 20
CA.ch.87 dB 18 23
< TUNER / ATSC >

1. Received Freq. Range (-28dBm) --- kHz --- 100
ch.4 dBm --- -76/0
2. ATSC Dynamic Range (min / max) ch.10 dBm --- -76/0
ch.41 dBm --- -76/+4
< LCD PANEL >

Horizontal pixels 1366 ---
1. Native Pixel Resolution
Vertical pixels 768 ---
2. Brightness (w / filter) --- cd/m2 300 ---
Horizontal -88 to 88 ---
3. Viewing Angle
Vertical -88 to 88 ---
< VIDEO >

Horizontal % 5 55
1. Over Scan
Vertical % 5 55
--- K 12000 ---
x 0.272 2%
y 0.278 2%
<Measurement condition>
Input signal: Internal pattern (40/70% raster)
2. Color Temperature Measurement point: Screen center
Measuring instrument: Made of KONICA MINOLTA Luminance meter CA-310
Aging time: 60min. (Retail MODE / 100IRE Raster HDMI
1080i@60)
MODE setting of TV: Shipment setting / Retail MODE
Ambient temperature: 25C 5C
Horizontal line 400 ---
3. Resolution (composite video)
Vertical line 350 ---
< AUDIO >

All items are measured across 8 load at speaker output terminal with L.P.F.
1. Audio MAX Output (ATSC 0dBfs) Lch/Rch W 5.0/5.0 4.0/4.0
2. Audio Distortion (NTSC) 500mW: Lch/Rch % 0.5/0.5 2.0/2.0
-6dB: Lch Hz 70 to 10 k 100 to 8 k
3. Audio Freq. Response (NTSC)
-6dB: Rch Hz 70 to 10 k 100 to 8 k
1-1 FL11.4SP
IMPORTANT SAFETY PRECAUTIONS
Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical
codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally
important to implement the following precautions when a set is being serviced.
Safety Precautions for LCD TV d. Leakage Current Hot Check - With the
instrument completely reassembled, plug the
Circuit AC line cord directly into a 120 V AC outlet. (Do
1. Before returning an instrument to the not use an isolation transformer during this
customer, always make a safety check of the test.) Use a leakage current tester or a
entire instrument, including, but not limited to, the metering system that complies with American
following items: National Standards Institute (ANSI) C101.1
a. Be sure that no built-in protective devices are Leakage Current for Appliances and
defective and have been defeated during Underwriters Laboratories (UL) 1410, (50.7).
servicing. (1) Protective shields are provided With the instrument AC switch first in the on
on this chassis to protect both the technician position and then in the off position, measure
and the customer. Correctly replace all missing from a known earth ground (metal water pipe,
protective shields, including any removed for conduit, etc.) to all exposed metal parts of the
servicing convenience. (2) When reinstalling instrument (antennas, handle brackets, metal
the chassis and/or other assembly in the cabinet, screw heads, metallic overlays, control
cabinet, be sure to put back in place all shafts, etc.), especially any exposed metal
protective devices, including but not limited to, parts that offer an electrical return path to the
nonmetallic control knobs, insulating chassis. Any current measured must not
fishpapers, adjustment and compartment exceed 0.5 milli-ampere. Reverse the
covers/shields, and isolation resistor/capacitor instrument power cord plug in the outlet and
networks. Do not operate this instrument or repeat the test.
permit it to be operated without all
protective devices correctly installed and READING SHOULD
functioning. Servicers who defeat safety NOT BE ABOVE 0.5 mA
features or fail to perform safety checks
may be liable for any resulting damage. LEAKAGE
DEVICE CURRENT
b. Be sure that there are no cabinet openings BEING TESTER
through which an adult or child might be able to TESTED + _
insert their fingers and contact a hazardous
voltage. Such openings include, but are not TEST ALL EXPOSED
limited to, (1) spacing between the Liquid METAL SURFACES
Crystal Panel and the cabinet mask, (2)
excessively wide cabinet ventilation slots, and
(3) an improperly fitted and/or incorrectly ALSO TEST WITH
secured cabinet back cover. PLUG REVERSED
c. Antenna Cold Check - With the instrument AC USING AC
plug removed from any AC source, connect an ADAPTER PLUG EARTH
electrical jumper across the two AC plug AS REQUIRED GROUND
prongs. Place the instrument AC switch in the
on position. Connect one lead of an ohmmeter ANY MEASUREMENTS NOT WITHIN THE
to the AC plug prongs tied together and touch LIMITS SPECIFIED HEREIN INDICATE A
the other ohmmeter lead in turn to each tuner POTENTIAL SHOCK HAZARD THAT MUST
antenna input exposed terminal screw and, if BE ELIMINATED BEFORE RETURNING THE
applicable, to the coaxial connector. If the INSTRUMENT TO THE CUSTOMER OR
measured resistance is less than 1.0 megohm BEFORE CONNECTING THE ANTENNA OR
or greater than 5.2 megohm, an abnormality ACCESSORIES.
exists that must be corrected before the
2. Read and comply with all caution and safety-
instrument is returned to the customer. Repeat
related notes on or inside the receiver cabinet, on
this test with the instrument AC switch in the off
the receiver chassis, or on the Liquid Crystal
position.
Panel.
2-1 LTVN_ISP
3. Design Alteration Warning - Do not alter or add 7. Product Safety Notice - Some electrical and
to the mechanical or electrical design of this TV mechanical parts have special safety-related
receiver. Design alterations and additions, characteristics which are often not evident from
including, but not limited to circuit modifications visual inspection, nor can the protection they give
and the addition of items such as auxiliary audio necessarily be obtained by replacing them with
and/or video output connections, might alter the components rated for higher voltage, wattage, etc.
safety characteristics of this receiver and create a Parts that have special safety characteristics are
hazard to the user. Any design alterations or identified by a # on schematics and in parts lists.
additions will void the manufacturer's warranty and Use of a substitute replacement that does not
may make you, the servicer, responsible for have the same safety characteristics as the
personal injury or property damage resulting recommended replacement part might create
therefrom. shock, fire, and/or other hazards. The product's
4. Hot Chassis Warning - safety is under review continuously and new
instructions are issued whenever appropriate.
a. Some TV receiver chassis are electrically
Prior to shipment from the factory, our products
connected directly to one conductor of the AC
are strictly inspected to confirm they comply with
power cord and maybe safety-serviced without
the recognized product safety and electrical codes
an isolation transformer only if the AC power
of the countries in which they are to be sold.
plug is inserted so that the chassis is
However, in order to maintain such compliance, it
connected to the ground side of the AC power
is equally important to implement the following
source. To confirm that the AC power plug is
precautions when a set is being serviced.
inserted correctly, with an AC voltmeter,
measure between the chassis and a known
earth ground. If a voltage reading in excess of
1.0 V is obtained, remove and reinsert the AC
power plug in the opposite polarity and again
measure the voltage potential between the
chassis and a known earth ground.
b. Some TV receiver chassis normally have 85V
AC(RMS) between chassis and earth ground
regardless of the AC plug polarity. This chassis
can be safety-serviced only with an isolation
transformer inserted in the power line between
the receiver and the AC power source, for both
personnel and test equipment protection.
c. Some TV receiver chassis have a secondary
ground system in addition to the main chassis
ground. This secondary ground system is not
isolated from the AC power line. The two
ground systems are electrically separated by
insulation material that must not be defeated or
altered.
5. Observe original lead dress. Take extra care to
assure correct lead dress in the following areas: a.
near sharp edges, b. near thermally hot parts-be
sure that leads and components do not touch
thermally hot parts, c. the AC supply, d. high
voltage, and, e. antenna wiring. Always inspect in
all areas for pinched, out of place, or frayed wiring.
Check AC power cord for damage.
6. Components, parts, and/or wiring that appear to
have overheated or are otherwise damaged
should be replaced with components, parts, or
wiring that meet original specifications.
Additionally, determine the cause of overheating
and/or damage and, if necessary, take corrective
action to remove any potential safety hazard.
2-2 LTVN_ISP
Precautions during Servicing
A. Parts identified by the # symbol are critical for
safety.
Replace only with part number specified.
B. In addition to safety, other parts and assemblies
are specified for conformance with regulations
applying to spurious radiation. These must also be
replaced only with specified replacements.
Examples: RF converters, RF cables, noise
blocking capacitors, and noise blocking filters, etc.
C. Use specified internal wiring. Note especially:
1) Wires covered with PVC tubing
2) Double insulated wires
3) High voltage leads
D. Use specified insulating materials for hazardous
live parts. Note especially:
1) Insulation Tape
2) PVC tubing
3) Spacers
4) Insulators for transistors.
E. When replacing AC primary side components
(transformers, power cord, etc.), wrap ends of
wires securely about the terminals before
soldering.
F. Observe that the wires do not contact heat
producing parts (heat sinks, oxide metal film
resistors, fusible resistors, etc.)
G. Check that replaced wires do not contact sharp
edged or pointed parts.
H. When a power cord has been replaced, check that
11~13 lb (5~6 kg) of force in any direction will not
loosen it.
I. Also check areas surrounding repaired locations.
J. Use care that foreign objects (screws, solder
droplets, etc.) do not remain inside the set.
K. When connecting or disconnecting the internal
connectors, first, disconnect the AC plug from the
AC supply outlet.
L. When installing parts or assembling the cabinet
parts, be sure to use the proper screws and
tighten certainly.
2-3 LTVN_ISP
Safety Check after Servicing
Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and
wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified
values in order to verify compliance with safety standards.
1. Clearance Distance
When replacing primary circuit components, confirm
specified clearance distance (d) and (d') between
soldered terminals, and between terminals and Chassis or Secondary Conductor
surrounding metallic parts. (See Fig. 1)
Primary Circuit
Table 1: Ratings for selected area
Clearance d' d
AC Line Voltage Region
Distance (d), (d)
U.S.A. or 3.2 mm
110 to 130 V
Canada (0.126 inches)
Note: This table is unofficial and for reference only. Be

sure to confirm the precise values.
Fig. 1
2. Leakage Current Test

Confirm the specified (or lower) leakage current
between B (earth ground, power cord plug prongs) and
externally exposed accessible parts (RF terminals, Exposed Accessible Part
antenna terminals, video and audio input and output
terminals, microphone jacks, earphone jacks, etc.) is
Z
lower than or equal to the specified value in the table
below.
Measuring Method: (Power ON) AC Voltmeter
(High Impedance)
Insert load Z between B (earth ground, power cord plug
prongs) and exposed accessible parts. Use an AC
voltmeter to measure across both terminals of load Z.
See Fig. 2 and following table.
Earth Ground
B
Power Cord Plug Prongs
Fig. 2
Table 2: Leakage current ratings for selected areas
AC Line Voltage Region Load Z Leakage Current (i) Earth Ground (B) to:
U.S.A. or 0.15 F CAP. & 1.5 k Exposed accessible
110 to 130 V i 0.5 mA rms
Canada RES. Connected in parallel parts
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.
2-4 LTVN_ISP
STANDARD NOTES FOR SERVICING
Circuit Board Indications How to Remove / Install Flat Pack-IC
1. The output pin of the 3 pin Regulator ICs is
1. Removal
indicated as shown.
With Hot-Air Flat Pack-IC Desoldering Machine:
Top View Bottom View 1. Prepare the hot-air flat pack-IC desoldering
Input machine, then apply hot air to the Flat Pack-IC
Out In (about 5 to 6 seconds). (Fig. S-1-1)
2. For other ICs, pin 1 and every fifth pin are

indicated as shown.
Pin 1
10
3. The 1st pin of every male connector is indicated as Fig. S-1-1

shown.
2. Remove the flat pack-IC with tweezers while
applying the hot air.
Pin 1 3. Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
Pb (Lead) Free Solder up. Then remove (glue will be melted). (Fig. S-1-6)
4. Release the flat pack-IC from the CBA using
Pb free mark will be found on PCBs which use Pb tweezers. (Fig. S-1-6)
free solder. (Refer to figure.) For PCBs with Pb free
mark, be sure to use Pb free solder. For PCBs CAUTION:
without Pb free mark, use standard solder. 1. The Flat Pack-IC shape may differ by models. Use
an appropriate hot-air flat pack-IC desoldering
machine, whose shape matches that of the Flat
Pack-IC.
2. Do not supply hot air to the chip parts around the
flat pack-IC for over 6 seconds because damage
to the chip parts may occur. Put masking tape
around the flat pack-IC to protect other parts from
damage. (Fig. S-1-2)
Pb free mark
3-1 TVN_SN
3. The flat pack-IC on the CBA is affixed with glue, so With Soldering Iron:
be careful not to break or damage the foil of each 1. Using desoldering braid, remove the solder from
pin or the solder lands under the IC when all pins of the flat pack-IC. When you use solder
removing it. flux which is applied to all pins of the flat pack-IC,
you can remove it easily. (Fig. S-1-3)
Hot-air
Flat Pack-IC Flat Pack-IC Desoldering Braid
Desoldering
Machine
CBA
Soldering Iron
Masking Flat Pack-IC Fig. S-1-3
Tape
Tweezers 2. Lift each lead of the flat pack-IC upward one by
one, using a sharp pin or wire to which solder will
Fig. S-1-2
not adhere (iron wire). When heating the pins, use
a fine tip soldering iron or a hot air desoldering
machine. (Fig. S-1-4)
Sharp
Pin
Fine Tip
Soldering Iron
Fig. S-1-4
3. Bottom of the flat pack-IC is fixed with glue to the

up. Then remove (glue will be melted). (Fig. S-1-6)
tweezers. (Fig. S-1-6)
3-2 TVN_SN
With Iron Wire: 2. Installation
1. Using desoldering braid, remove the solder from 1. Using desoldering braid, remove the solder from
all pins of the flat pack-IC. When you use solder the foil of each pin of the flat pack-IC on the CBA
flux which is applied to all pins of the flat pack-IC, so you can install a replacement flat pack-IC more
you can remove it easily. (Fig. S-1-3) easily.
2. Affix the wire to a workbench or solid mounting 2. The I mark on the flat pack-IC indicates pin 1.
point, as shown in Fig. S-1-5. (See Fig. S-1-7.) Be sure this mark matches the
3. While heating the pins using a fine tip soldering pin 1 on the PCB when positioning for installation.
iron or hot air blower, pull up the wire as the solder Then presolder the four corners of the flat pack-IC.
melts so as to lift the IC leads from the CBA (See Fig. S-1-8.)
contact pads as shown in Fig. S-1-5. 3. Solder all pins of the flat pack-IC. Be sure that
4. Bottom of the flat pack-IC is fixed with glue to the none of the pins have solder bridges.
up. Then remove (glue will be melted). (Fig. S-1-6) Example :
tweezers. (Fig. S-1-6)
Note: When using a soldering iron, care must be
taken to ensure that the flat pack-IC is not
being held by glue. When the flat pack-IC is
removed from the CBA, handle it gently
because it may be damaged if force is applied.
Pin 1 of the Flat Pack-IC
is indicated by a " " mark.
Hot Air Blower Fig. S-1-7
or
Presolder
Iron Wire
Soldering Iron
To Solid
Mounting Point
Fig. S-1-5
Flat Pack-IC
CBA
Fine Tip Fig. S-1-8

CBA Soldering Iron
Flat Pack-IC
Tweezers
Fig. S-1-6
3-3 TVN_SN
Instructions for Handling Semi-
conductors
Electrostatic breakdown of the semi-conductors may
occur due to a potential difference caused by
electrostatic charge during unpacking or repair work.
1. Ground for Human Body

Be sure to wear a grounding band (1 M) that is
properly grounded to remove any static electricity that
may be charged on the body.
2. Ground for Workbench

Be sure to place a conductive sheet or copper plate
with proper grounding (1 M) on the workbench or
other surface, where the semi-conductors are to be
placed. Because the static electricity charge on
clothing will not escape through the body grounding
band, be careful to avoid contacting semi-conductors
with your clothing.
<Incorrect>
CBA
<Correct> Grounding Band
1M
CBA
1M
Conductive Sheet or
Copper Plate
3-4 TVN_SN
CABINET DISASSEMBLY INSTRUCTIONS
[TYPE A]
1. Disassembly Flowchart Step/
Fig.
Loc. Part Removal Note
This flowchart indicates the disassembly steps for the No.
No.
cabinet parts and the CBA in order to gain access to
items to be serviced. When reassembling, follow the Function D2
[9] Function Knob ---
steps in reverse order. Bend, route and dress the CBA Unit D3
cables as they were. Front
[10] D2 --------------- ---
Cabinet
[1] Stand
Assembly
(1) (2) (3) (4) (5)
[3] Digital Main
[2] Rear Cabinet [6] Speaker
CBA Unit *1: LC320EM2 (Serial No.: DS1),
32MF301B/F7 (Serial No.: DS1),
[4] Power Supply LC320SS2 (Serial No.: DS1)
CBA
*2: LC320EM2 (Serial No.: DS3),
[8] IR Sensor [9] Function 320MF301B/F7 (Serial No.: DS2),
[5] Stand Bracket
CBA Unit CBA Unit
LC320SS2 (Serial No.: DS2)
[7] LCD Module Note:
Assembly
(1) Order of steps in procedure. When reassembling,
[10] Front follow the steps in reverse order. These numbers
Cabinet are also used as the Identification (location) No. of
parts in figures.
2. Disassembly Method (2) Parts to be removed or installed.
(3) Fig. No. showing procedure of part location
Step/
Fig. (4) Identification of parts to be removed, unhooked,
No. unlocked, released, unplugged, unclamped, or
No.
desoldered.
Stand P = Spring, L = Locking Tab, S = Screw,
[1] D1 3(S-1) ---
Assembly H = Hex Screw, CN = Connector
Rear 10(S-2), 3(S-3), e.g. 2(S-2) = two Screws of (S-2),
[2] D1 --- 2(L-2) = two Locking Tabs of (L-2)
Cabinet 2(S-4), 13(L-1)
(5) Refer to the following "Reference Notes in the
4(S-5), CN3005,
Digital Main D2 CN3101, CN3102, Table."
[3] ---
CBA Unit D3 CN3701, CN3801,
CN3802, Jack Holder
6(S-6), CN200,
Power CN600*1, CN601*2,
D2
[4] Supply CN1100, CN1101, ---
D3
CBA CN1102,
Connector Cover*1
Stand
[5] D2 (S-7) ---
Bracket
4(S-8),
[6] Speaker D2 ---
Speaker Holder
LCD
[7] Module D2 --------------- ---
Assembly
IR Sensor D2
[8] Sensor Lens ---
CBA Unit D3
4-1 FL11.4-A_DC
(L-1)
(S-2)
(L-1)
(S-2)
(S-3)
(L-1)
(L-1)
(S-3)
[2] Rear Cabinet (S-2)

(S-4)
(S-2)
[1] Stand Assembly
(S-1)
Fig. D1
4-2 FL11.4-A_DC
[10] Front Cabinet
[9] Function
CBA Unit [7] LCD Module
Assembly
Function [3] Digital Main

Knob CBA Unit
Jack Holder
Sensor Lens
[8] IR Sensor
CBA Unit [5] Stand Bracket (S-5)
(S-7)
Speaker (S-8)
(S-6) Holder
Speaker (S-8)
Holder
*1
Connector Cover [6] Speaker
[4] Power Supply CBA (S-6) *1: LC320EM2 (Serial No.: DS1),
(S-6) 32MF301B/F7 (Serial No.: DS1),
LC320SS2 (Serial No.: DS1)
Fig. D2
4-3 FL11.4-A_DC
TV Cable Wiring Diagram
To LCD Module
Assembly
Power Supply CBA
CN200
To LCD Module
Assembly
CN1102
Digital Main
CBA Unit
CN3005
CN632 CN3701
CN1101
CN3102 CN3101
CN3802 CN3801
CN1100
*1 CN600
*2 CN601
To Speaker
IR Sensor CBA Unit To AC Cord
CN4052
Function CBA Unit
CN4001
*1: LC320EM2 (Serial No.: DS1), *2: LC320EM2 (Serial No.: DS3),
32MF301B/F7 (Serial No.: DS1), 320MF301B/F7 (Serial No.: DS2),
LC320SS2 (Serial No.: DS1) LC320SS2 (Serial No.: DS2) Fig. D3
4-4 FL11.4-A_DC
[TYPE B]
1. Disassembly Flowchart Step/
Fig.
This flowchart indicates the disassembly steps for the No.
No.
cabinet parts and the CBA in order to gain access to
items to be serviced. When reassembling, follow the Function D2
[9] Function Knob ---
steps in reverse order. Bend, route and dress the CBA Unit D3
cables as they were. Front
[10] D2 --------------- ---
Cabinet
[1] Stand
Assembly
(1) (2) (3) (4) (5)
[3] Digital Main
[2] Rear Cabinet [6] Speaker
CBA Unit Note:
(1) Order of steps in procedure. When reassembling,
[4] Power Supply
CBA follow the steps in reverse order. These numbers
are also used as the Identification (location) No. of
[8] IR Sensor
[5] Stand Bracket
[9] Function parts in figures.
CBA Unit CBA Unit
(2) Parts to be removed or installed.
[7] LCD Module (3) Fig. No. showing procedure of part location
Assembly
(4) Identification of parts to be removed, unhooked,
unlocked, released, unplugged, unclamped, or
[10] Front
Cabinet desoldered.
P = Spring, L = Locking Tab, S = Screw,
H = Hex Screw, CN = Connector
2. Disassembly Method e.g. 2(S-2) = two Screws of (S-2),
2(L-2) = two Locking Tabs of (L-2)
Step/
Fig. (5) Refer to the following "Reference Notes in the
No. Table."
No.
Stand
[1] D1 3(S-1) ---
Assembly
Rear 10(S-2), 3(S-3),
[2] D1 ---
Cabinet 2(S-4), 13(L-1)
4(S-5), CN3005,
Digital Main D2 CN3101, CN3102,
[3] ---
CBA Unit D3 CN3701, CN3801,
CN3802, Jack Holder
Power 6(S-6), CN200,
D2
[4] Supply CN601, CN1100, ---
D3
CBA CN1101, CN1102
Stand
[5] D2 (S-7) ---
Bracket
4(S-8),
[6] Speaker D2 ---
Speaker Holder
LCD
[7] Module D2 --------------- ---
Assembly
IR Sensor D2
[8] Sensor Lens ---
CBA Unit D3
4-5 FL11.4-B_DC
(L-1)
(S-2)
(L-1)
(S-2)
(S-3)
(L-1)
(L-1)
(S-3)
[2] Rear Cabinet (S-2)

(S-4)
(S-2)
[1] Stand Assembly
(S-1)
Fig. D1
4-6 FL11.4-B_DC
[10] Front Cabinet
[9] Function
CBA Unit [7] LCD Module
Assembly
Function [3] Digital Main

Knob CBA Unit
Jack Holder
Sensor Lens
[8] IR Sensor
CBA Unit [5] Stand Bracket (S-5)
(S-7)
Speaker (S-8)
(S-6) Holder
Speaker (S-8)
Holder
[6] Speaker
[4] Power Supply CBA (S-6)

(S-6)
Fig. D2
4-7 FL11.4-B_DC
TV Cable Wiring Diagram
To LCD Module
Assembly
Power Supply CBA
CN200
To LCD Module
Assembly
CN1102
Digital Main
CBA Unit
CN3005
CN632 CN3701
CN1101
CN3102 CN3101
CN3802 CN3801
CN1100
CN601
To Speaker
To AC Cord
IR Sensor CBA Unit
CN4052
Function CBA Unit
CN4001
Fig. D3
4-8 FL11.4-B_DC
ELECTRICAL ADJUSTMENT INSTRUCTIONS
General Note: CBA is abbreviation for How to set up the service mode:
Circuit Board Assembly.
Note: Electrical adjustments are required after
Service mode:
replacing circuit components and certain 1. Turn the power on.
mechanical parts. It is important to perform 2. Press [MENU] button to display Setup menu.
these adjustments only after all repairs and 3. Select Features.
replacements have been completed.
4. Select Current Software Info.
Also, do not attempt these adjustments unless
the proper equipment is available. 5. Press [0], [4], [2], [5], [7], [4] and [INFO] buttons on
the remote control unit in this order. The following
Test Equipment Required screen appears.
1. Remote control unit "*" differs depending on the models.
2. Color Analyzer, Code: *******-**-**-****-**
CA-310 (KONICA MINOLTA Luminance meter) or Pic code: **********-***-*-**
measuring instrument as good as CA-310. Panel-Option code: **-***-***-***-***
MIPS: Push 0 key
Press "POWER" key to exit.
Tuner: ****-*****-****
Safety: Safety_Non
HDMI EDID: ** Total Watch Time: *****
PC EDID: ** Lightsensor: ****
5-1 LC9EA
1. Purity Check Mode 2. VCOM Adjustment
This mode cycles through full-screen displays of red, Test Point Adj. Point
green, blue, and white to check for non-active pixels.
[CHANNEL UP/DOWN]
1. Enter the Service mode. Screen
buttons
2. Each time the [7] button on the remote control unit
is pressed, the display changes as follows. M. EQ. Spec.
Color analyzer See below
Purity Check Mode
Figure
White mode
To avoid interference from ambient
[7] button
light, this adjustment should be
performed in a dark room.
Perpendicularity
[7] button
Black mode
Color Analyzer
[7] button
Red mode
1. Operate the unit for more than 60 minutes.
2. Set the color analyzer at the zero point calibration
and bring the optical receptor pointing at the
center of the LCD-Panel.
[7] button Note: The optical receptor must be set
Green mode perpendicularly to the LCD Panel surface.
3. Enter the Service mode.
4. Press [3] button on the remote control unit.
5. Press [CHANNEL UP/DOWN] buttons on the
remote control unit so that the color analyzer value
[7] button becomes minimum.
Blue mode 6. To cancel or to exit from the VCOM Adjustment,
press [CH RETURN] or [PREV CH] button.
[7] button
White 20% mode
Note:
When entering this mode, the default setting is White mode.
3. To cancel or to exit from the Purity Check Mode,

press [CH RETURN] or [PREV CH] button.
5-2 LC9EA
The White Balance Adjustment should be 6. Press [MENU] button. The internal Raster signal
performed when replacing the LCD Panel appears on the screen. (Internal (Single)
appears on the upper right of the screen as shown
or Digital Main CBA.
below.)
3. White Balance Adjustment
Purpose: To mix red and blue beams correctly for Internal (Single)
pure white.
Symptom of Misadjustment: White becomes bluish
or reddish.
ITEM SPECIFICATION
HDB 0
x= 0.272 0.002
Color temperature
y= 0.278 0.002
Internal pattern
Input Signal 7. Press [CHANNEL UP/DOWN] buttons to adjust
(40/70% raster)
the color temperature becomes 12000K
Measurement point Screen center (x= 0.272 / y= 0.278 0.002).
CA-310 (KONICA MINOLTA 8. Press [1] button to select the HDR for High Drive
Luminance meter) or Red adjustment (HDR appears on the screen.)
M. EQ.
measuring instrument as and press [CHANNEL UP/DOWN] buttons to
good as CA-310. adjust the color temperature.
60min. 9. If necessary, adjust the HDB or HDR again.
Aging time (Retail MODE/100IRE Raster
HDMI 1080i@60) 10. Press [6] button to select the LDB for Low Drive
Blue adjustment (LDB appears on the screen.)
Shipment setting/ and press [CHANNEL UP/DOWN] buttons to
MODE setting of TV
Retail MODE adjust the color temperature.
Ambient
25C 5C
temperature
Internal (Single)
1. Operate the unit for more than 60 minutes.
2. Enter the Service mode.
3. Press [VOLUME DOWN] button three times on the
remote control unit to select Drive setting mode.
Drive appears on the screen.
LDB 0
4. Set the color analyzer at the CHROMA mode and
zero point calibration. Bring the optical receptor
pointing at the center of the LCD-Panel.
11. Press [4] button to select the LDR for Low Drive
To avoid interference from ambient Red adjustment (LDR appears on the screen.)
light, this adjustment should be and press [CHANNEL UP/DOWN] buttons to
performed in a dark room.
adjust the color temperature.
Perpendicularity 12. If necessary, adjust the LDB or LDR again.
13. Press [VOLUME DOWN] button to shift to the
Debugging Message mode.
If there is no message under [WB] section, this
adjustment completes.
If Drive settings are NG. Retry. is displayed,
Color Analyzer repeat above steps from 5. to 12. Then check
Debugging Message again. If Drive settings are
NG. Retry. is displayed, replace the LCD Panel or
Note: The optical receptor must be set Digital Main CBA.
perpendicularly to the LCD Panel surface. 14. To cancel or to exit from the White Balance
5. Press [3] button to select the HDB for High Drive Adjustment, press [CH RETURN] or [PREV CH]
Blue adjustment. (HDB appears on the screen.) button.
5-3 LC9EA
HOW TO INITIALIZE THE LCD TV
The purpose of initialization is to place the set in a new out of box condition. The customer will be prompted to
select a language and program channels after the set has been initialized.
To put the program back at the factory-default, initialize the LCD TV using the following procedure.
1. Turn the power on.
2. Enter the service mode.
- To cancel the service mode, press [POWER]
button on the remote control unit.
3. Press [FREEZE] button on the remote control unit
to initialize the LCD television.
4. "INITIALIZED" will appear in the upper right of the
screen. "INITIALIZED" color will change to green
from red when initializing is completed.
6-1 LC9_INT
FIRMWARE RENEWAL MODE
Equipment Required 4. The update will start and the following will appear
on the screen.
a. USB storage device
"*" differs depending on the models.
b. Remote Control Unit Software Upgrade
Software upgrade in progress. Please wait.

Firmware Update Procedure Do not remove the USB storage device or
turn the TV off while upgrade is in progress.
Note: There are two states (the User Upgrade and
the Factory Upgrade) in firmware update. Current Version: *******-***-*-***-****
New Version: *******-***-*-***-****
User Upgrade Upgrade the firmware only.
The setting values are not *1 Downloading...
0%
initialized.
Factory Upgrade Upgrade the firmware and
Note: If the above screen isnt displayed, repeat from
(Firmware initialize the setting values.
step 1.
upgrade)
Factory Upgrade Upgrade the firmware and The appearance shown in *1 is described as follows.
(Flash upgrade) initialize the setting values Appearance State
along with the setting data Downloading the firmware from
adjusted at the factory such as Downloading...
the USB storage device.
White Balance, etc.
Writing the downloaded firmware
Writing...
The identification of User Upgrade and Factory in flash memory.
Upgrade are done by the filename. Checking... Checking the new firmware.
1. Turn the power off and unplug the AC Cord.
2. Insert the USB storage device to the USB port as 5. When the firmware update is completed, the
shown below. following will appear on the screen.
Software Upgrade
Rear Cabinet
USB port
USB storage
device
The software upgrade is completed.

Remove USB storage device, turn TV off then on again.
Remove the USB storage device from the USB

port.
Turn the power off and turn the power on again.
Note:
When the Factory Upgrade is used, after
3. Plug the AC cord in the wall outlet and turn the restarting TV, shift to initial screen menu in service
power on. mode. "INITIALIZED" will appear on the upper
right of the screen. "INITIALIZED" color will
change to green from red when initializing is
completed.
7-1 FL11.4FW
TROUBLESHOOTING
[Power Supply Section]
FLOW CHART NO.1
The power cannot be turned on.
No
Is the fuse (F601) normal? See FLOW CHART No.2 <The fuse blows out.>
Yes
Is normal state restored when once unplugged No

power cord is plugged again after several seconds? Check if there is any leak or short-circuiting on the
Yes primary circuit component, and service it if defective.
No (D600, D601, D602, D603, Q600, Q601, T600)
Is the P-ON+24V line voltage normal?
Yes
Check each rectifying circuit of the secondary

circuit and service it if defective.
FLOW CHART NO.2

The fuse blows out.
Check the presence that the primary component Check the presence that the rectifying diode or circuit
is leaking or shorted and service it if defective. is shorted in each rectifying circuit of secondary side,
and service it if defective.
After servicing, replace the fuse.
FLOW CHART NO.3

When the output voltage fluctuates.
Does the photocoupler circuit on the No Check IC601, D648, Q631, Q634 and their periphery
secondary side operate normally? circuit, and service it if defective.
Yes
Check IC601, D607, D609 and their periphery circuit,

and service it if defective.
FLOW CHART NO.4

When buzz sound can be heard in the vicinity of power circuit.
Check if there is any short-circuit on the rectifying diode and the circuit in each rectifying circuit of the secondary side,
and service it if defective. (IC202, Q212, Q213, Q221, Q222, Q636, D634, D637, D642, D643, D644, D646, D660)
8-1 FL11.4ATR
FLOW CHART NO.5
P-ON+24V is not output.
Is approximately +24V voltage supplied to the No Check C648, D637, D644, D646, D648 and their
cathode of D637? periphery circuit, and service it if defective.
Yes
Check if there is any leak or short-circuit on
the loaded circuit, and service it if defective.
FLOW CHART NO.6

LCD+24.5V is not output.
No
Is approximately +35V voltage supplied to the collector Check C647, D660 and their periphery circuit,
of Q212? and service it if defective.
Yes
No
Is approximately +25V voltage supplied to the base Check Q210, Q211, D207, P-ON-H1 line and their
of Q212? periphery circuit, and service it if defective.
Yes
Replace Q212.
FLOW CHART NO.7

PANEL+15.8V is not output.
No
Is approximately +22V voltage supplied to the Check C637, D640, D645 and their periphery circuit,
collector of Q221? and service it if defective.
Yes
No
Is approximately +16V voltage supplied to the Check Q210, Q211, D202, D221, D222, P-ON-H1
base of Q221? line and their periphery circuit, and service it if defective.
Yes
Replace Q221.
FLOW CHART NO.8

AMP+24V is not output.
No
Is approximately +24V voltage supplied to the cathode Check C631, D634 and their periphery circuit,
of D634? and service it if defective.
Yes
Check if there is any leak or short-circuit on

the loaded circuit, and service it if defective.
8-2 FL11.4ATR
FLOW CHART NO.9
AL+5V is not output.
No
Is approximately +24V voltage supplied to the See FLOW CHART No.5 <P-ON+24V is not output.>
collector of Q636?
Yes
No
Is approximately +5.6V voltage supplied to the Check D656 and their periphery circuit, and service
base of Q636? it if defective.
Yes
Replace Q636.
FLOW CHART NO.10

P-ON+3.3V is not output.
No
Is approximately +8.5V voltage supplied to Pin(1) of Check C639, D643 and their periphery circuit, and
IC202? service it if defective.
Yes
No
Is approximately +7.5V voltage supplied to Pin(2) of Check Q207, Q208 P-ON-H2 line and their periphery
IC202? circuit, and service it if defective.
Yes
Replace IC202.
FLOW CHART NO.11

LCD-6V is not output.
No
Is approximately -9.5V voltage supplied to the anode Check C638, D642 and their periphery
of D642? circuit, and service it if defective.
Yes
No
Is approximately -9V voltage supplied to the base of Check Q210, Q211, D208, P-ON-H1 line and their
Q213? periphery circuit, and service it if defective.
Yes
Replace Q213.
8-3 FL11.4ATR
[Video Signal Section]
FLOW CHART NO.1
The key operation is not functioning.
No
When pressing each switches (SW4001~SW4007) Replace the Function CBA Unit.
do the voltage of Pin(2) of CN4001 decrease?
Yes
Replace Digital Main CBA Unit.
FLOW CHART NO.2

No operation is possible from the remote control unit.
Operation is possible from the unit.
No
Is approximately +3.3V voltage supplied to Pin(3) Check AL+3.3V line and service it if defective.
terminal of the remote control receiver (RS4051)?
Yes
No
Is the "L" pulse sent out Pin(1) terminal of remote Replace the IR Sensor CBA Unit
control receiver (RS4051) when the infrared remote or the remote control unit.
control is activated?
Yes
No
Is the "L" pulse supplied to Pin(2) of CN4052? Replace the IR Sensor CBA Unit.
Yes
Replace Digital Main CBA Unit.
FLOW CHART NO.3

Picture does not appear normally.
No
Is approximately +5.7V voltage supplied to Pin(11) of See FLOW CHART NO.9 <AL+5V is not output.
CN632? [Power Supply Section]>
Yes
No
Is approximately +24V voltage supplied to Pin(13, 14) See FLOW CHART NO.8 <AMP+24V is not output.
of CN632? [Power Supply Section]>
Yes
No
Is approximately +24V voltage supplied to Pin(16, 17) of See FLOW CHART NO.5 <P-ON+24V is not output.
Yes
CL3005, Digital Main CBA Unit or LCD Module

Assembly may be defective.
Check and replace these parts.
8-4 FL11.4ATR
[Audio Signal Section]
FLOW CHART NO.1
Audio is not outputted normally.
No
Is approximately +5.7V voltage supplied to Pin(11) of See FLOW CHART NO.9 <AL+5V is not output.
Yes
No
Is approximately +24V voltage supplied to Pin(13, 14) See FLOW CHART NO.8 <AMP+24V is not output.
of CN632? [Power Supply Section]>
Yes
No
Is approximately +24V voltage supplied to Pin(16, 17) of See FLOW CHART NO.5 <P-ON+24V is not output.
Yes
No
Are the audio signals outputted to Pin(1) of CN3801 Replace Digital Main CBA Unit.
and Pin(1) of CN3802?
Yes
SP3801, SP3802, CL3801 or CL3802 may be

defective. Check and replace these parts.
8-5 FL11.4ATR
FUNCTION CBA UNIT
IC3005
(MAIN MICRO CONTROLLER)
CN3101 CN4001
KEY-IN1 A15 2 KEY-IN1 2 KEY SWITCH
REMOTE C14
LED1 J16
Q3501
LED DRIVE
RS4051
REMOTE
SENSOR
CN3102 CN4052 D4051

2 REMOTE 2 STANDBY
TO AUDIO-MUTE 5 LED1 5
VIDEO/AUDIO G13 AUDIO-MUTE AL+3.3V
BLOCK DIAGRAM AL+3.3V
IR SENSOR CBA UNIT

1. System Control Block Diagram
P-ON-H2 B16 Q3006
Q3005
9-1
CN3701 CN632
P-ON-H2
7 P-ON-H2 7
P-ON-H1
P-ON-H1 C1 6 P-ON-H1 6 TO
PROTECT1
PROTECT1 C13 5 PROTECT1 5 POWER SUPPLY
VCOM-PWM BLOCK DIAGRAM
VCOM-PWM F2 1 VCOM-PWM 1 DRIVE
IC3006 (MEMORY) PROTECT3
IC200, Q202,
BACKLIGHT-SW TO VIDEO/AUDIO Q203, Q204
SCK 6 T11 SFCX BLOCK DIAGRAM
CN3701 CN632
SI 5 P11 SFTX PROTECT3
BLOCK DIAGRAMS
PROTECT3 B13 4 PROTECT3 4

SO 2 R11 SFRX BACKLIGHT-SW TO INVERTER
BACKLIGHT-SW E2 2 BACKLIGHT-SW 2 BLOCK DIAGRAM
CS 1 P12 SFCS-N BACKLIGHT-ADJ
BACKLIGHT-ADJ F3 3 BACKLIGHT-ADJ 3
TU3401 (TUNER UNIT)
SCL R12 4 SCL POWER SUPPLY CBA

SDA T12 3 SDA
X3001
25MHz H15 XIN25
OSC H16 XOUT25
DIGITAL MAIN CBA UNIT
FL11.4ABLS
VIDEO SIGNAL AUDIO SIGNAL
VGA-R-IN
1
VGA-G-IN
2 VGA-B-IN
VGA-HSYNC
JK3001 3
VGA-VSYNC
PC-RGB IC3013
13 BUFFER GATE PC-SCL
IN
IC3014 PC-SDA
14 BUFFER GATE
TU3401 (TUNER UNIT)
15
DIF-OUT1
12 DIF-OUT1 6
DIF-OUT2
DIF-OUT2 7
IF-AGC
IF-AGC 5
WF1
JK3701
COM-VIDEO-Y/VIDEO-IN
COMPONENT COM-VIDEO-Pb-IN
-Y/VIDEO-IN WF2
COM-VIDEO-Pr-IN
COMP-DET
COMPONENT
-Pb-IN WF3
2. Video/Audio Block Diagram
COMPONENT
-Pr-IN
TO DIGITAL
SIGNAL PROCESS
BLOCK DIAGRAM
WF4
9-2
JK3701 Q3702
AUDIO(L)
BUFFER
AUDIO(L)-IN AUDIO(R)
Q3703
BUFFER
AUDIO(R)-IN
Q3701
JK3702 SPDIF
DIGITAL BUFFER
AUDIO-OUT
(COAXIAL)
IC3801 (AUDIO AMP)
AMP(L)-OUT
11,12 DRIVE PWM 19
AMP(R)-OUT
39,40 DRIVE PWM 32
CN3801
SP3801 SP(L) 1 Q3802 AUDIO-MUTE
SPEAKER GND 2 MUTE CONTROL 34
L-CH Q3804
STANDBY 17 P-ON+5V TO SYSTEM CONTROL
BLOCK DIAGRAM
Q3803 BACKLIGHT-SW
CN3802
SP3802 SP(R) 1
SPEAKER GND 2
R-CH
FL11.4ABLV
LCD MODULE
IC3005 (DIGITAL SIGNAL PROCESS) ASSEMBLY
VGA-HSYNC
A14 HSIN
VGA-VSYNC CN3005
B14 VSIN
P14 23 LLV0(+)
VGA-R-IN P13 22 LLV0(-)
C11
VGA-G-IN N16 21 LLV1(+)
A9
VGA-B-IN N15 20 LLV1(-)
C7
COM-VIDEO-Y/VIDEO-IN A/D P16 19 LLV2(+)
C9 SW
COM-VIDEO-Pb-IN CONVERTER P15 18 LLV2(-)
D8 LVDS TX
COM-VIDEO-Pr-IN T16 13 LLV3(+)
TO B11
VIDEO/AUDIO T15 12 LLV3(-)
C10
BLOCK DIAGRAM R14 11 LLV4(+)
DIF-OUT1 T14 10 LLV4(-)
A12 DEMODULATOR
DIF-OUT2 R13 9 LLV5(+)
B12 /MPEG DECODER
T13 8 LLV5(-)
IF-AGC
A16 IF-AGC R16 16 LLVCLK(+)
COMP-DET
N12 COMP-DET R15 15 LLVCLK(-)
AUDIO(L) TP L13 6 TP
A8 POL M15 5 POL
AUDIO(R)
B8 CPV L16 4 CPV
SPDIF
N10 AUDIO I/F OE L15 3 OE1
AMP(L)-OUT
B7 STV M14 1 STV
AMP(R)-OUT
A7
JK3003
HDMI-IN1 IC3018 (HDMI SW)
TMDS-D0(+)
7 42
TMDS-D0(-)
9 41
TMDS-D1(+)
4 45 AUDIO DIGITAL
TMDS-D1(-) SIGNAL
6 44 DECODER
TMDS-D2(+) PROCESS
9-3
1 48
TMDS-D2(-)
3 47
TMDS-CLOCK(+)
10 39
TMDS-CLOCK(-)
12 38 26 B4
3. Digital Signal Process Block Diagram
SDA
16 36 27 A4
SCL
15 37 23 B3
24 A3
JK3002 HDMI HDMI
SW 20 B2 I/F
HDMI-IN2
21 A2
TMDS-D0(+) 17 B1
7 8
TMDS-D0(-) 18 A1
9 7
TMDS-D1(+)
4 11
TMDS-D1(-)
6 10
TMDS-D2(+)
1 14
TMDS-D2(-) IC3002
3 13 VIDEO (DDR2 SDRAM)
TMDS-CLOCK(+)
10 5 DECODER
TMDS-CLOCK(-)
12 4 N4,N7,N8,P3,P4, B1,B9,C2,C8,
SDA D1,D3,D7,D9,
16 1 P6-P8,R3,R4,R6,
SCL R8,T2-T5 F1,F9,G2,G8, DATA(0-15)
15 2 H1,H3,H7,H9
M2,M3,M7,M8,
H1,H2,J1,J2,J4,K1, N2,N3,N7,N8, ADDRESS(0-12)
IC3011 K3,L1,L2,M1-M3,N1 P2,P3,P7,P8,R2
(HDMI SERIAL EEPROM)
2 SCL1
3 SDA1 SCL0 7 G14 HDMI-SCL
10 SCL3 SDA0 6 F14 HDMI-SDA
11 SDA3
TO PC-SCL
VIDEO/AUDIO 15 SCL2
PC-SDA
BLOCK DIAGRAM 14 SDA2
FL11.4ABLD
CN1100
T1100 1 BACK
2 LIGHT
2 8
4 7
1 6
3 5
+24V
IC1200
(PWM CONTROL)
Q1300 Q1303
+24V +12V REG. 7 STB
Q1700
21 SWITCHING CN1101
T1101 1 BACK
2 LIGHT
24
4. Inverter Block Diagram
Q1301 Q1701 2 8
4 7
12 DUTY SWITCHING
BACKLIGHT-SW LOGIC OUTPUT
TO SYSTEM CONTROL BACKLIGHT-ADJ Q1201 1 6
BLOCK DIAGRAM PROTECT3 Q1702
3 5
17 4 SWITCHING
FEED
BACK PWM
16 2
Q1703
SWITCHING
9-4
CN1102
PROTECT
T1102 1 BACK
2 LIGHT
2 8
13 18
4 7
1 6
3 5
Q1202
LCD MODULE
POWER SUPPLY CBA ASSEMBLY
FL11.4BLINV
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. NOTE:
CAUTION ! : For continued protection against risk of fire,
If Main Fuse (F601) is blown , check to see that all components in the power supply The voltage for parts in hot circuit is measured using
replace only with same type 4 A, 125V fuse.
circuit are not defective before you connect the AC plug to the AC power supply. 4A/125V hot GND as a common terminal.
ATTENTION : Utiliser un fusible de rechange de mme type de 4A, 125V.
Otherwise it may cause some components in the power supply circuit to fail.
HOT CIRCUIT. BE CAREFUL.
LCD MODULE ASSEMBLY
*2 Q213 CN200
CN601 SW-9.5V 8 LCD-6V
AC600 2,3 PANEL+15.8V
AC CORD *1 F601 L600 L601 D600- D603 T600 Q200, Q201,
CN600 4A/125V Q212 Q206 6,7 P-ON+3.3V
2 LINE LINE BRIDGE 3 9 SW+24V SW 4 VGH
1 FILTER FILTER RECTIFIER 10 VCOM
10
CN632 CN3701
4A/125V Q210,Q211 13,14 AMP+24V 13,14 AMP+24V
4 SWITCHING 11 AL+5V 11 AL+5V
*1 LC320EM2 (Serial No. : DS1),
32MF301B/F7 (Serial No. : DS1), 11 16,17 P-ON+24V 16,17 P-ON+24V
LC320SS2 (Serial No. : DS1)
*2 LC320EM2 (Serial No. : DS3,TH1), DIGITAL MAIN CBA UNIT

32MF301B/F7 (Serial No. : DS2,TH1),
LC320SS2 (Serial No. : DS2,TH1)
12
5 Q214
13
Q221, Q222,
5. Power Supply Block Diagram
D221
8 14 SW+16V
9-5
Q600 7 15
SWITCHING
Q636
+5V REG.
VCOM-PWM
P-ON-H1 TO SYSTEM
P-ON-H2 CONTROL
IC202 BLOCK
PROTECT1
IC601 +3.3V REG. DIAGRAM
PROTECT3
4 1
Q601
Q207,Q208
SWITCHING
3 2 SWITCHING
CONTROL
Q634
FEED
BACK
+24V
Q635
Q631
Q632
HOT COLD
POWER SUPPLY CBA
FL11.4ABLP
SCHEMATIC DIAGRAMS / CBA AND TEST POINTS
Standard Notes
WARNING
Many electrical and mechanical parts in this chassis
have special characteristics. These characteristics
often pass unnoticed and the protection afforded by
them cannot necessarily be obtained by using
replacement components rated for higher voltage,
wattage, etc. Replacement parts that have these
special safety characteristics are identified in this
manual and its supplements; electrical components
having such features are identified by the mark # in
the schematic diagram and the parts list. Before
replacing any of these components, read the parts list
in this manual carefully. The use of substitute
replacement parts that do not have the same safety
characteristics as specified in the parts list may create
shock, fire, or other hazards.
Notes:
1. Do not use the part number shown on these
drawings for ordering. The correct part number is
shown in the parts list, and may be slightly
different or amended since these drawings were
prepared.
2. All resistance values are indicated in ohms
(K = 103, M = 106).
3. Resistor wattages are 1/4W or 1/6W unless
otherwise specified.
4. All capacitance values are indicated in F
(P = 10-6 F).
5. All voltages are DC voltages unless otherwise
specified.
6. This schematic diagrams are masterized version
that should cover the entire FL11.4 chassis models.
Thus some parts in detail illustrated on this
schematic diagrams may vary depend on the
model within the FL11.4 chassis.
Please refer to the parts lists for each models.
7. The Circuit Board layout illustrated on this service
manual is the latest version for this chassis at the
moment of making this service manual.
Depend on the mass production date of each
model, the actual layout of each Board may differ
slightly from this version.
10-1 FL11.4SC
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON
THE FOLLOWING PAGES:
1. CAUTION:
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME
TYPE_A,_V FUSE.
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MME TYPE DE_A,_V.
2. CAUTION:
Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F601) is blown, first check to see that all components in the power supply circuit are not
defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components
in the power supply circuit to fail.
3. Note:
1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since the drawings were prepared.
2. To maintain original function and reliability of repaired units, use only original replacement parts which are
listed with their part numbers in the parts list section of the service manual.
4. Voltage indications on the schematics are as shown below:

Plug the TV power cord into a standard AC outlet.:
1 2 3
(Unit: Volt) 5.0 5.0 Power on mode
Voltage Indicates that the voltage

is not consistent here.
5. How to read converged lines

1-D3
Distinction Area 3 1-B1
Line Number AREA D3
(1 to 3 digits)
2 AREA B1
Examples:
1. "1-D3" means that line number "1" goes to the line number
"1" of the area "D3". 1 1-D3
2. "1-B1" means that line number "1" goes to the line number
"1" of the area "B1". A B C D
6. Test Point Information

: Indicates a test point with a jumper wire across a hole in the PCB.
: Used to indicate a test point with a component lead on foil side.
: Used to indicate a test point with no test pin.
: Used to indicate a test point with a test pin.
The reference number of parts on Schematic Diagrams/CBA can be retrieved by

application search function.
10-2 FL11.4SC
Power Supply 1 Schematic Diagram
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
CAUTION ! : For continued protection against risk of fire, NOTE:
If Main Fuse (F601) is blown , check to see that all components in the power supply
replace only with same type 4 A, 125V fuse. The voltage for parts in hot circuit is measured using
circuit are not defective before you connect the AC plug to the AC power supply.
4A/125V ATTENTION : Utiliser un fusible de rechange de mme type de 4A, 125V. hot GND as a common terminal.
HOT CIRCUIT. BE CAREFUL. CONTINUE

21.9 15.8 POWER 2
F601 PANEL+15.8V
AC600 CN600 4A/125V D661 D662 R233 Q222 R239
AC CORD OPEN OPEN WIRE 2SA950-O 21.9 8.2/1W P-ON+3.3V
2 D640 (SW+15.8V)
SK2B-TR JS660 21.9 15.8 LCD-6V
1
R601 4A 125V R235 R234 Q221 C220
LCD+24.5V
1.2M/1/2W C637 D645
470/25V 1ZB22BB R269 WIRE 2.2 16.0 2SC2120-Y 470/25V C222
OPEN
OR 12K /1/2W (SW+15.8V) R236 R265 R265A
CN601 SA601 11K C229 8.2K OPEN
2 SURGE R247 R237 Q214 R248 OPEN
ABSORBER 100K D222 R270 C221 750 KTC3875S-Y-RTK/P R268A 56K
OPEN
4 1
C600
0.47/250V R611
2.2/5W
C610
1000P/250V
R246
3.9K
R240
3.9K
1.5K 0.01
D221
KIA431-AT/P
2.2 (SWITCHING)
R238 0
2.2K
0.7
R268
47K
R241
6.8K
R249
6.8K
D212
D211
L600
LINE FILTER D611 R602 C611 D202 R242
1ZB220 2.2/5W 1000P/250V R266A R267 2.7K
-YBB OPEN R266 47K
R650 D649 D650 R642 R643 47K
1 SK16-T/R 5V6BSB-T26 43K 47K
C601 D601 D602
0.47/250V 1N5406-BU 1N5406-BU
C641 C644
2200P/1KV 1/50V C633
L601 OPEN 2.6 CONTINUE
LINE D600 D603 C612 D637 -3.5 R263 POWER 3
FILTER 1N5406-BU 1N5406-BU 1000P/250V SB3150BH 470 C228 R264 D210
Q633 Q213 2.2/50V 15K 6V2BSB-T26 +24V
D646 KTC3875S-Y-RTK/P 0 KTC3875S-Y-RTK/P R263A
SB3150BH (RESET) (SW-9.5V) OPEN
-9.6 D652
D644 D648 31.9 37.8 D208 -8.9 Q212
SB3150BH C648 C649 KTC3875S-Y-RTK/P
T600 2200/35V 2200/35V 1ZB30BB Q210 R260 R255
390 (SW+24V)
POWER TRANS 37.1 2SA1576UBTLQ 47K -9.6 TO DIGITAL MAIN
D634 (SWITCHING) 35.2 24.2 CN632 CBA UNIT CN3701
SB3150BH R261 R255A 0 19
3 15 22K D207 OPEN 24.8 GND
C603 C602 C604 R613 R612 C613 C614 C631
1000/35V R631
R251
22k R252 R256 0 18 GND
D612
OPEN
270 390 270 68K 68K 2200P OPEN 15K 39K WIRE
/200V /200V /200V /1W /1W /1KV 4 14 Q211
24.0 17 P-ON+24V
R603 D642 0.1 KTC3875S-Y-RTK/P R253 24.0 16 P-ON+24V
220K D613 SK16-T/R (SWITCHING) 22K
3 R604
220K
R600
220K
BC602
BEAD
BC601
BEAD
FR155-B/P 5 13
12
C638
100/25V 0 0.7 R254
22K
R258
2.7K
R258A R257
8.2K
R257A
OPEN C227 D205
24BSC-T26
C635
0.1
0 15
24.4 14
24.4 13
0 12
GND
AMP+24V
AMP+24V
OPEN 22/50V GND
D639 D206 5.7 11
7 11 AL+5V
R606A R605A D643 R259 C636 0 10 GND
Q600 OPEN OPEN SK16-T/R OPEN 0.1
TK10A50D 10 R262 0.6 9 OE2
165.8 D 12K R259A D663 2.6 8
(SWITCHING) C605 R606 R605 D660 OPEN RESET
G 3.7 0.1 180 220 RS1GJTB R664 10K 3.4 7
8 9 P-ON-H2
0.1 S C647 R663 C639 3.3 6 P-ON-H1
100/50V 39K 100 D641
R607A /10V 3.1 5 PROTECT1
C606 OPEN D609 3.1 4
1200P C231 C634 D632 PROTECT3
3.7 R607 R657A 0.1 0.1 5V6BSB-T26 0.7 3
0.4 1.2K OPEN BACKLIGHT-ADJ
0.9 2 BACKLIGHT-SW
D604 0 D605 R636A R635A R657 D638 1.6 1
27BSB-T26 4V3BSB-T26 OPEN OPEN 15 VCOM-PWM
24.0 6.4 D657 10BSB-T26
C607 Q601 IC601 C632
2SC2120-Y R636 R635 1000/35V D655 Q636
820P SWITCHING TLP781F 120 120 3V3BSB-T26 5.6 KTC3199-GR-AT/P
/2KV R610A R610 (D4-FUNBLL F) R645 (SW+6V)
CONTROL OPEN 270 27K
ERROR
VOLTAGE DET R637 R644 R647 R660 R634 R634A
14.0 23.7 10K 18K C645 27K WIRE WIRE OPEN
2200P R662 R656 R658 R659
4 1 220 220 220 220
2 C609
1500P 0.4 3 2 22.7
D631
5V6BSB-T26
Q631
KTC3875S-Y-RTK/P
R649A
OPEN
R649
3.9K
Q634
KTC3875S-Y-RTK/P
22.7 (FEED BACK)
R662A R656A R658A R659A
OPEN OPEN OPEN OPEN
D656
R633 R633A
WIRE OPEN
R641
22K
CONTINUE
POWER 2
PROTECT3
VCOM-PWM
19.3 (SWITCHING) 6.2 R651 5V6BSB-T26 OE2
5.6 820
0.1 P-ON-H1
0 R632 R652
D607 47K D654 18K P-ON-H1-1
*2 5V6BSB-T26
IC202
R608 PQ200WNA1ZPH
0.18 D610 D606 D609A R609 C608 (+3.3V REG.) R654 CONTINUE
1ZB36BB OPEN OPEN 3.9K 0.068 0.1 10K POWER 3
/2W 0.6
VIN
ADJ
GND
BACKLIGHT-SW
VC
VO
0 Q635 R655 D635 C646

1 2 3 4 5 KTC3875S-Y-RTK/P 47K D636 D658 D659 1ZB7.5BB 100/10V BACKLIGHT-ADJ
(SWITCHING) OPEN OPEN
PROTECT3
8.5 7.4 3.3 1.3 0
D633
C230 5V6BSB-T26
C223 100/10V R245A
OPEN
R245
OPEN
1 D651
2 NOTE
C216 C217 Q207
0.1 10/50V 2SA1576UBTLQ You cannot mix components under Type 1 with
R228 (SWITCHING)
4.7K 8.6 8.6 the ones under Type 2.
1 C225
0.1
R227
47K
*2
R226
330
R243
240
7.9 R229
22K R230
10K
0.1
R232
10K 1.6
0.1
Refer to Parts List of LC320EM2(Serial No.: DS1).
Type 1 Type 2
*2 0.7 0 Q632
KTC3875S-Y-RTK/P R638 IC202 KIA78R000ZF-RTF/P PQ200WNA1ZPH
C224 R244 0 Q208 R231 C226 (SWITCHING) 22K
OPEN 2.2K KTC3875S-Y-RTK/P 47K 3.3/50V
(SWITCHING) R226 1.4k 330
HOT COLD POWER SUPPLY CBA R244 1k 2.2k
UNLESS OTHERWISE SPECIFIED:

DIODES ARE 1SS133.
A B C D E F
10-3 FL11.4SCM1
POWER SUPPLY CBA
CONTINUE
POWER 1
4 PANEL+15.8V
P-ON+3.3V
LCD-6V
LCD+24.5V
CONTINUE
POWER 1
PROTECT3
D201
R225 1SS133 VCOM-PWM
10K
OE2
P-ON-H1
C200 C212 P-ON-H1-1
0.1 R209A R209 0.1 R217
OPEN 10 10K
C211 15.7
1000P 7.3
Q202 7.0
KTC3875S-Y-RTK/P
(V-COM DRIVE)
R210 R207
0 1
C208 C209 C210
22/50V
3 R212
100K
R214
OPEN
Q203
2SA1576UBTLQ
(V-COM DRIVE)
7.3
7.0
0
J200
OPEN
OPEN OPEN
R220
OPEN Q205
OPEN
R211 R211A C215
R213 10 OPEN R221
0 OPEN OPEN
R216
1.2K
TO LCD MODULE R224 C213 R218
47K C214 R215 15K
ASSEMBLY CN200 15.87.4 7.0 7.0 1 47/25V 12K
GND 1 0 8 7 6 5
LCD+15.8V 2 15.8 VCC 7.0 R219
IC200
LCD+15.8V 3 15.8 TL3472CDR 0.2 1K
VGH 4 20.0 (COMPARATOR) VEE 0 Q204
C218
GND 5 0 OPEN 1 2 3 4 KTC3875S-Y-RTK/P
(V-COM DRIVE)
P-ON+3.3V 6 3.3 0 0 0 0
P-ON+3.3V 7 3.3
LCD-6V 8 -6.1
C201 C202 C675
9 0
2 GND
VCOM
GND
10 7.0
11 0
0.1 0.1 OPEN R208
0
R202
OPEN
19.9 23.9
Q200
C207 C206 R204 R203 2SA1576UBTLQ
R203A (SWITCHING) 23.5 R200 C204 D200 C203
OPEN OPEN OPEN 560 2K 100K OPEN 1SS133 2.2/50V
JS200
R223
OPEN
R201
1K
0.6 R222
1.2 10K
Q201 0.6 Q206

KTC3875S-Y-RTK/P C205 KTC3875S-Y-RTK/P
18.4 (SWITCHING) R205 0.1 (SWITCHING)
1K
0.4 R206
0 100K
G H I J K L
10-4 FL11.4SCM2
4 POWER SUPPLY CBA

CONTINUE CN1100
POWER 1
+24V 1 BACK
Q1300 C1700 C1709 R1301 C1701 C1104 D1503 2 LIGHT
2SA1576UBTLQ 2200/35V 2200/35V 47K OPEN C1702 C1710 10P/6.3KV R1100 R1101 DAN202U
1 1 39K 0
R1305 (SW+12V) 24.0
510/2W 12.0 12.0 R1302 D1700 D Q1700 C1105 C1118 R1102
51K R1700 1SS133 TK50P04M1 330P 330P 2.2K
C1304 C1305 C1303 C1302 100 21.2 G (SWITCHING) R1103A OPEN
220/35V 0.1 11.2 0.1 10/50V T1100
R1309 INVERTER R1104 R1105
10K D1701 C1703 R1701 17.5 S TRANS R1143 OPEN 100 13 D1506
15BSB-T26 1000P 10K DAN202U
D1300 R1300 C1300 C1100 2.2 R1103 470
5V6BSB-T26 10K 0.1 2 8
R1222 R1704 R1106A OPEN
D1301 10 4.7/1W C1101 2.2 4 7
5V6BSB-T26 R1107 R1108
C1705 R1146 OPEN 100 13
0.022 C1102 2.2 1 6
Q1303 17.5 D Q1701 R1106 470
2SA1576UBTLQ R1702 D1702 TK50P04M1 3 5
(SW+12V) 100 1SS133 C1103 2.2
1.6 G (SWITCHING) R1109 R1110
12.0 11.9 39K 0
D1703 C1704 R1703 0 S C1116 2.2
R1304 15BSB-T26 1000P 10K C1106 C1107 C1119 R1111
R1307 11.2 4.7K 10P/6.3KV 330P 330P 2.2K
1K 24.0 C1117 2.2
3 R1306
10K
0.1
4.7K
Q1301
R1303
R1308 4.7K
C1301
1000P R1705
100
D1705
D1704
1SS133
C1706
21.2 G
D Q1702
R1706 17.5 S
TK50P04M1
(SWITCHING)
0.7 KTC3875S 15BSB-T26 1000P 10K CN1101

C1311 R1310 -Y-RTK/P 1
0 (SWITCHING) BACK
1000P 22K R1223 C1108 2 LIGHT
10 R1709 10P/6.3KV R1112 R1113 D1504
4.7/1W 39K 0 DAN202U
17.5 D Q1703 C1708 C1109 C1120 R1114

R1707 D1706 TK50P04M1 0.022 330P 330P 2.2K
100 1SS133 R1115A OPEN
1.6 G (SWITCHING) T1101
INVERTER R1116 R1117
R1220 R1145 OPEN
OPEN D1707 C1707 R1708 0 S TRANS 100 13 D1507
15BSB-T26 1000P 10K R1115 470 DAN202U
IC1200 2 8
BD9244AFV R1118A OPEN
(PWM CONTROL) D1200 D1202 4 7
D1201 1SS133 1SS133 R1148 OPEN R1119 R1120
CONTINUE 1SS133 1 6 100 13
POWER 1 0 1 24 1.8 R1216 R1221 R1118 470
BACKLIGHT-SW 100 1 R1501 100K 3 5
1.8 2 REG 23 7.6 R1121 R1122
BACKLIGHT-ADJ C1204 C1205 D1500 R1502 100K 39K 0
PROTECT3 23.8 3 22 24.1 0.1 2.2 R1229 DAN202U
OUTPUT JS1200 0 R1503 100K C1110 C1111 C1121 R1123
10P/6.3KV 330P 330P 2.2K
C1208 21.8 4 21 21.2 C1209
0.47 0.47 C1500 R1500 R1504 100K
2 C1206 C1201
17.8 5
11.9 6 VCC
LOGIC
20 16.9
VLO 19 2.2
Q1203
OPEN
(SWITCHING) 0
7.6
5.1
R1225
R1227
OPEN
R1228
OPEN
0.01 1M
D1501
DAN202U
R1505
R1506
100K
100K
CN1102
10/50V 0.1 5.9 7 STB OPEN
PWM 18 0.2 5.1 R1507 100K 1 BACK
R1205 R1204 R1226 0.2 LIGHT
560K 75K 2.0 8 C1112 2
17 0.8 OPEN
0 Q1204
R1508 100K 10P/6.3KV R1124
39K
R1125
0
D1505
DAN202U
C1213 FEED OPEN
0.01 BACK R1509 100K
9 OSC 16 1.2 (SWITCHING) C1113 C1122 R1126
R1202 C1203 D1502 R1510 100K 330P 330P 2.2K
0 10 GND 6800P
130K 15 1.1 DAN202U T1102 R1127A OPEN
R1213 R1214 C1202 R1511 100K INVERTER R1128 R1129
4.7K 0 0 11
R1203
8.2K 14 0 6800P TRANS R1147 OPEN 100 13 D1508
DUTY PROTECT R1512 100K R1127 470 DAN202U
3.1 12 13 0 2 8
R1209
4.7K
C1207
1000P 4 7
R1130A OPEN
R1131 R1132
LCD
C1210
0.47 1 6
R1150 OPEN 100 13 MODULE
3 5
R1130 470
R1133 R1134
ASSEMBLY
39K 0
R1215 R1212 3.1 C1114 C1115 C1123 R1135
10K 10K 0.1 10P/6.3KV 330P 330P 2.2K
Q1201
C1211 R1208 KTC3875S-Y-RTK/P
1 OPEN
3.1
22K 0 (SWITCHING)
R1206
10K
D1203
1SS133
R1201
68K
C1501
1000P
R1513
1M
-0.2 R1515 R1516
27K 6.8K
0 Q1202 R1207 C1200 C1212 R1200 C1214
KTC3875S-Y-RTK/P 33K OPEN 0.47 68K OPEN C1502 R1514
3300P 39K
(SWITCHING)
M N O P Q R
10-5 FL11.4SCM3
Function Schematic Diagram IR Sensor Schematic Diagram
(NO CONNECTION) CN4002

R4051 R4052 C4054
GND 1 0.1
56 6.8K
2
KEY-IN1 2
2 R4054
1K
CN4052
1
2
TO DIGITAL MAIN
CBA UNIT CN3102
GND
REMOTE
RS4051 C4055 3 AL+3.3V
GP1USC32XP OPEN
TO DIGITAL MAIN 4 P-ON+5V
CBA UNIT CN3101 CN4001 (REMOTE SENSOR)
R4055 R4059 5 LED1
GND 1 IC4051 OPEN OPEN
VOUT
OPEN 6 KEY-IN1
VCC
GND
KEY-IN1 2 D4051 (LIGHT SENSOR) 7 LIGHT
3 2 1 19-21SURC
/S530-A2/TR 1 6
STANDBY AMP
R4057 2 GND 5
R4006 R4007 R4005 R4004 R4003 R4002 R4001 OPEN LOGIC
0 2.2K 2.2K 2.7K 4.7K 8.2K 18K 3 VCC NU 4
D4052 C4057 R4058 R4056
C4004 C4002 D4001 C4051 C4056 C4052 R4060 R4053 OPEN OPEN OPEN OPEN
OPEN 0.1 EDZTE615.6B 10 10 1000P OPEN 4.7K
SW4006 SW4007 SW4005 SW4004 SW4003 SW4002 SW4001 D4002
POWER CH UP CH MENU SOURCE VOL VOL OPEN
DOWN UP DOWN C4053
0.1
CN4051 (NO CONNECTION)
1 1 1 GND
2 KEY-IN1
FUNCTION CBA UNIT IR SENSOR CBA UNIT

UNLESS OTHERWISE SPECIFIED:
SWITCHES ARE SKRMABE010.
A B C A B C
10-6 FL11.4SCF_IR
Digital Main 1 Schematic Diagram
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3005.
IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.
CONTINUE
DIGITAL 4
VCOM-PWM CONTINUE
OE2 DIGITAL 4
R3045 R3026 R3021 C3054 Q3002 R3025 R3027 C3751 C3752 C3753 P-ON+24V
OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN
P-ON+3.3V
4 (NO CONNECTION)
LCD+12V
LCD+12V
CN3011
31
30
R3047
OPEN
R3044
OPEN
R3046
OPEN
C3058
OPEN
C3057
OPEN
R3034
OPEN
1
2
3
8
7
6
C3047
OPEN
C3061
OPEN
C3045
OPEN
R3038
OPEN
R3037
OPEN CN3006
30
(NO CONNECTION)
LCD+21V
LCD+12V 29 D3004 29 LCD+21V
OPEN
GND 28 R3048 4 5 28 GND
OPEN Q3007 R3023
GND 27 OPEN OPEN Q3001 27 VCOM-PWM
LCD+12V 26 OPEN R3039 26 PWR-CTRL
C3077 R3022 OPEN
LCD+12V 25 OPEN OPEN R3035 25 P-ON+3.3V
OPEN
GND 24 24 GND
NU 23 23 LLV0(+)
NU 22 R3028 22 LLV0(-)
OPEN
D0(-) 21 21 LLV1(+)
D0(+) 20 20 LLV1(-)
D1(-) 19 19 LLV2(+)
D1(+) 18 18 LLV2(-)
GND 17 17 GND
D2(-) 16 16 LLVCNK(+)
D2(+) 15 15 LLVCLK(-)
GND 14 14 GND
CK(-) 13 13 LLV3(+)
3 CK(+)
D3(-)
D3(+)
12
11
10
12
11
10
LLV3(-)
LLV4(+)
LLV4(-)
NU 9 9 LLV5(+)
NU 8 8 LLV5(-)
GND 7 7 GND
GND 6 6 TP
GND 5 5 POL
GND 4 *1 4 CPV
NU 3 IC3005(1/6) 3 OE1
R8A05011BG-U0
NU 2 DIGITAL SIGNAL PROCESS 2 XA0
NU 1 /MAIN MICRO CONTROLLER 1 STV
C3352 0.5P TO LCD MODULE

R16 CN3005 ASSEMBLY
R15 24 GND
P14 C3349 0.5P 23 LLV0(+)
P13 22 LLV0(-)
N16 C3350 0.5P 21 LLV1(+)
2 LVDS
TX
N15
P16
P15
C3351 0.5P
C3353 0.5P
20
19
18
LLV1(-)
LLV2(+)
LLV2(-)
T16 17 GND
T15 16 LLVCNK(+)
R14 C3354 0.5P 15 LLVCLK(-)
T14 14 GND
R13 C3355 0.5P 13 LLV3(+)
T13 12 LLV3(-)
11 LLV4(+)
10 LLV4(-)
9 LLV5(+)
TO DIGITAL 8 LLV5(-)
MAIN 2
IC3005(2/6) 7 GND
TP L13 6 TP
POL M15 5 POL
CPV L16 4 CPV
OE L15 3 OE1
R3152 1K
STV M14 2 XA0
OE2 L14 1 STV
1 NU M16
100P
100K
100K
100K
100K
100K
47P
47P
47P
47P
NU M13 R3511
22 CN3702 (NO CONNECTION)
CELL-PWR-CTRL N14
R3041
R3161
R3162
R3163
R3164
C3161
C3162
C3163
C3164
C3165
NU N13 R3088 1 LCD+21V

7.5K 2 LCD+21V
NU K15
3 GND
4 GND
A B C D E F
10-7 FL11.4SCD1
1 NOTE:
TU3401 TUNER UNIT DIGITAL MAIN CBA UNIT

IC3013
DIF-OUT1
DIF-OUT2
74LVC1G126GW CONTINUE
IF-AGC
(BUFFER GATE) DIGITAL 6
+3.3V
GND
SDA
SCL
1 VCC 5 HDMI-33V
C3214
1 2 3 4 5 6 7 2 0.1
4 C3402 0.1
C3403 0.1
3 GND 4 CONTINUE
DIGITAL 6
PC-SDA
PC-SCL
C3408 D3401 R3406 0 IC3014 PC+5V
OPEN EDZTE615.6B 74LVC1G126GW
R3404 0 (BUFFER GATE)
1 VCC 5 CONTINUE
L3401 DIGITAL 4
BLM21PG221SN1D
2 P-ON+3.3V
C3410 C3407 C3401 C3409 C3406 C3175 C3176 R3204 P-ON+5V
10P 0.1 10 0.1 33P OPEN OPEN 4.7K 3 GND 4
R3409 D3027
OPEN D3403 D3402 R3203 1SS400
EDZTE615.6B EDZTE615.6B C3405 4.7K
33P
R3298 R3296
*1 C3411 C3404 R3417 D3404 100 100
IC3005(2/6) 10P 1000P OPEN EDZTE615.6B R3326 R3321
R8A05011BG-U0 4.7K 4.7K JK3001(REAR)
DIGITAL SIGNAL PROCESS L3024 C3243 R3369 PC-RGB-IN
/MAIN MICRO CONTROLLER OPEN OPEN OPEN
R3206 22
SCL R12 R3361
R3207 22 OPEN D3041 D3054
SDA T12 R3354 OPEN OPEN 11 6 1
TO DIGITAL 0
B12
MAIN 5 DEMODULATOR R3338 C3226
IC3005(5/6) 0 OPEN L3022 C3235 D3040 12 7 2
/MPEG
3 DECODER
A12
R3337
0
C3225
OPEN
OPEN OPEN
R3353
0
R3360
OPEN
1SS400
R3343
100
R3376
100 13 8 3
R3202 R3194 R3358 D3050 14 9 4

2.7K 1K 10K OPEN
IF-AGC A16 L3023 C3242 R3368 R3339
R3205 C3178 C3177 OPEN OPEN OPEN 100
NU D1 18K 0.1 OPEN 15 10 5
R3347 D3045
10K OPEN
R3284
47
HSIN A14 D3049
R3356 OPEN
VSIN B14 R3285 75
C3194 0.1 47
A9
C3195 0.1 R3364 D3053
C7 R3286 75 OPEN
C3196 0.1 47
C11
R3377 D3055
SW C3198 0.01 75 OPEN
C10
C3199 0.1 R3327 10
C9
C3200 0.1 R3328 10 CONTINUE
D8 DIGITAL 3
C3201 0.1 R3329 10
B11 COMP-DET
A/D NU A10
33P
33P
33P
33P
33P
33P
CONVERTER
NU C8
2 NU D9
C3287
C3288
C3289
C3291
C3292
C3293
NU B9 R3403
0
WF1 JK3701(REAR)
COMPONENT
C3701 R3701 -Y/VIDEO-IN
DIGITAL R3402 39P 75 WF2
SIGNAL 0
PROCESS COMPONENT
C3702 R3702 -Pb-IN
R3401 39P 75 WF3
0
COMPONENT
Q3702 C3703 R3703 -Pr-IN
2SC4081UBTLQ R3713 R3706 39P 75 WF4
(BUFFER) 75K 51K
C3704 AUDIO(L)-IN
C3197 C3335 R3719 C3710 R3714 1 R3704
0.1 2.2 C3285 0.1 OPEN 100P 100K R3707 100K
TO DIGITAL TO DIGITAL NU B10 51K
MAIN 6 MAIN 1 C3286 0.1
IC3005(6/6) IC3005(1/6) NU A11 R3717 AUDIO(R)-IN
C3336 1 2.2K C3705 R3705
NU D10 1 100K
L3701 Q3703
BK1608HS601-T 2SC4081UBTLQ
(BUFFER)
C3714 C3708 C3713 R3715 C3712 CONTINUE
10 0.1 0.1 75K 0.1 R3716 DIGITAL 5
1 9.2
3.8
4.3
Q3701
R3710
100
R3711
7.5K
R3712
C3707
1
R3718
2.2K
R3720
OPEN
C3711
100P 100K AUDIO(L)-IN
AUDIO(R)-IN
2SC4081UBTLQ 10K C3716

JK3702(REAR) C3706 R3709 (BUFFER) OPEN
DIGITAL 1 220 CONTINUE
DIGITAL 5
AUDIO-OUT
(COAXIAL) C3709 C3715 R3708 SPDIF
100P OPEN 110
G H I J K L
10-8 FL11.4SCD2
1 NOTE:
*1
C3009 IC3005(3/6)
0.1 R8A05011BG-U0
DIGITAL SIGNAL PROCESS
R3064 C3050 /MAIN MICRO CONTROLLER C3184
100 0.1 16P
M5 SD-VREF0 XIN25 H15
R3065 C3051 N3 GND XOUT25 H16 X3001
100 0.1 25MHz
R3223 C3183 CN3012 (NO CONNECTION)
4 IC3002
SD-DQ15
SD-DQ14
R8
N8
SD-DQ15
SD-DQ14
ASEBRKAK-N F15
1K 16P 1
2
3
AL+3.3V
GND
ASEBRKAK-N
K4T51163QI-HCF7 SD-DQ13 ASEMD0 F16 4 ASEMD0
(DDR2 SDRAM) P7 SD-DQ13 TRST-N E16 5 TRST-N
SD-DQ12 R6 SD-DQ12
C3029 OPEN TCK E15 6 TCK
*A VDD SD-DQ11 P6 SD-DQ11
C3030 0.1 VREF J2 TDI D16 7 TDI
C3010 SD-DQ10 N7 SD-DQ10
C3031 OPEN 0.1 TDO D15 8 TDO
SD-DQ9 T5 SD-DQ9
C3032 0.1 TMS E14 9 TMS
CKE K2 SD-DQ8 P8 SD-DQ8
C3033 OPEN R3522 10 CPU-RESET-N
E2 NU CK J8 SD-DQ7 P4 SD-DQ7 10K
C3034 0.1
A2 NU CK K8 SD-DQ6 T3 SD-DQ6 CN3010 (NO CONNECTION)
C3035 OPEN R3395 4.7K
R8 NU CS L8 SD-DQ5 R4 SD-DQ5 1 P-ON+5V
C3036 0.1 R3468 100
R7 NU RAS K7 SD-DQ4 T2 SD-DQ4 TXD0 G15 2 UART0-TX
C3037 OPEN R3469 100
R3 NU CAS L7 SD-DQ3 P3 SD-DQ3 RXD0 G16 3 UART0-RX
C3038 0.1 R3396 4.7K C3253
WE K3 SD-DQ2 T4 SD-DQ2 NU G1 OPEN 4 GND
C3039 OPEN
1-O3 B7 UDQS BA2/NU L1 SD-DQ1 R3 SD-DQ1
C3040 0.1
2-O3 A8 UDQS/NU BA1 L3 SD-DQ0 N4 SD-DQ0 NU G2
C3041 OPEN CONTINUE
3-O3 B3 UDM BA0 L2 3-M3 T6 SD-UDM DIGITAL 2
SD-DQ15 B9 DQ15 A12 R2 6-M3 R5 SD-LDM COMP-DET
R3516 100
SD-DQ14 2-M3 BACKLIGHT-ADJ F3
3 SD-DQ13
SD-DQ12
SD-DQ11
B1
D9
D1
D3
DQ14
DQ13
DQ12
DQ11
A11
A10/AP
A9
A8
P7
M2
P3
P8
R3049
100
1-M3
5-M3
4-M3
T7
R7
N5
P5
SD-UDQSN
SD-UDQS
SD-LDQSN
SD-LDQS
VCOM-PWM F2
GND J14
R3517 100 CONTINUE
DIGITAL 5
CPU-RESET-N
BACKLIGHT-SW
SD-DQ10 D7 DQ10 A7 P2
SD-DQ9 C2 DQ9 A6 N7 R3050 15
SD-DQ8 L4 SD-WE CONTINUE
C8 DQ8 A5 N3 R3024 6.8 NU F13 DIGITAL 4
4-O3 F7 LDQS A4 N8 R1 SD-CLKN GPY10 E13 GPY10
R3015 6.8
5-O3 E8 LDQS/NU A3 N2 R2 SD-CLK CPU-RESET-N
R3016 15 R3211 100
6-O3 F3 LDM A2 M7 L3 SD-CKE P-ON-H2 B16 P-ON-H2
R3040 15 R3514 100
SD-DQ7 F9 DQ7 A1 M3 H2 SD-A8 DTV-ON-H2 K14 DTV-ON-H2
R3029 15 R3210 100
SD-DQ6 F1 DQ6 A0 M8 H1 SD-A4 DTV-ON-H1 K16 DTV-ON-H1
R3020 15
SD-DQ5 H9 DQ5 ODT K9 N2 SD-BA0 P-ON-H1 C1 P-ON-H1
R3070 150
SD-DQ4 H1 DQ4 H4 NU BACKLIGHT-ADJ
SD-DQ3 R3030 15x4 M2 SD-A12 R3188 22
H3 DQ3 VSS *B BACKLIGHT-SW E2 BACKLIGHT-SW
SD-DQ2 H7 DQ2 *A:A1,A9,C1,C3,C7,C9,E1,E9, N1 SD-A7 VCOM-PWM
R3503
SD-DQ1 G2 DQ1 G1,G3,G7,G9,J1,J9,M9,R1 M3 SD-A3 10K
SD-DQ0 G8 DQ0 *B:A3,A7,B2,B8,D2,D8,E3,E7, P1 SD-BA2 CONTINUE
F2,F8,H2,H8,J3,J7,N1,P9 R3031 15x4 K2 SD-ODT DIGITAL 5
R3515 4.7K
L2 SD-A9 LED1 J16 LED1
R3233 22
M1 SD-A5 AUDIO-MUTE G13 AUDIO-MUTE
R3213 22
2 R3032 15x4
L1
J2
K3
SD-A1
SD-A11
SD-A6
REMOTE C14
R3234
OPEN
REMOTE
K1 SD-A2
CONTINUE
J1 SD-A0 DIGITAL 4
R3033 15x4 J3 SD-RAS R3201 P-ON+1.8V
IC3006 R3215 22 33K
MX25L3205DM2I-12G R3102 H3 SD-CAS SFWP-N N12 P-ON+3.3V
(MEMORY) 10K
J4 SD-A10 AL+3.3V
1 CS VCC 8 K4 SD-BA1 P-ON+5V
R3107 C3073
10K 0.1
2 SO NU 7
R3089 47
P12 SFCS-N
3 WP SCK 6 R3092 47
R11 SFRX
R3093 47
4 GND SI 5 P11 SFTX C3072 10
R3094 47 NU H14
R3479 T11 SFCX C3071 0.1
10K R3095 22
T9 VBUS-EN
R3096 0
R9 VBUS-ST
C3246 D3052 C3348 R10 USBDP
(USB JACK) CN3009 1 OPEN 100/16V
T10 USBDN
BUS-POWER 1 R3099 5.6K
P10 NU
USBDN 2 IC3019
1 USBDP
GND
3
4 L3025
EXC24CG900U
C3327
0.1
BD2224G-TR
(EEPROM)
1 VIN VOUT 5
2 GND
3 /EN /OC 4
R3480 L3041
10K BLM21PG221SN1D
M N O P Q R
10-9 FL11.4SCD3
1 NOTE:

CONTINUE
*1 DIGITAL 3
IC3005(4/6) R3221 P-ON+1.8V
R8A05011BG-U0 100
DIGITAL SIGNAL PROCESS P-ON+3.3V
/MAIN MICRO CONTROLLER
4 VCC33STB F12
VCC33STB G12 C3160
0.1
R3220
0
C3182
0.1
G
R3222
10K L3027
MPZ1608S221AT
R3464
R3106
22K
R3100
22K
AL+3.3V
P-ON+5V
VDD12STB E12 D S OPEN D3105 CONTINUE

L3030 Q3006 R3105 Q3101 OPEN IC3004 DIGITAL 6
BEAD Q3013 2SA1576UBUBTLQ 1K 2SC4081UBTLQ BD7820FP-E2 P-ON+3.3V
SSM3K309T (SWITCHING) (SWITCHING) R3424 D3103 (+1.2V REG.)
C3181 (SW+12V) 100 1SS400 AL+3.3V
0.1
R3465 R3423 C3265 P-ON+3.3V(1)
CTL
VCC
GND
OUT
L3017 0 47K 10
C
BLM21PG221SN1D
R3097 1 2 3 4 5 CONTINUE
L3015 2.2K DIGITAL 2
BLM21PG221SN1D
VDD12 *A Q3005 P-ON+3.3V
C3121 C3122 C3123 C3124 C3125 C3126 2SC4081UBTLQ D3104 L3001 C3023 C3024 C3027 R3060 R3061 C3019
OPEN OPEN 0.1 0.1 OPEN 0.1 (SWITCHING) 1SS400 BLM21PG221SN1D C3108 OPEN 10 0.1 20K 33K 0.022 P-ON+5V
100/16V
D3101 D3106 R3059 R3062
1SS400 1SS400 1K 1.8K CONTINUE
C3127 C3128 C3129 C3134 C3132 C3133 D3102 DIGITAL 1
OPEN 0.1 OPEN 10 10 10 1SS400 R3043 C3049 C3263 C3086 P-ON+24V
L3020 R3084 R3086 180 100/4V 2.2 10
BLM21PG221SN1D 2.2K 2.2K P-ON+3.3V
AVDD12 M10 C3131 IC3007
C3135 Q3003 1 BD7820FP-E2
0.1 L3021 R3077 2SC4081UBTLQ (+1.8V REG.)
BLM21PG221SN1D 10K (SWITCHING)
AVDD12 E8
CTL
VCC
GND
OUT
C3136 C3137 C3155 C3156 Q3004 CONTINUE
3 AVDD12 F8 R3079
C
0.1 1 1 1 10K 2SC4081UBTLQ DIGITAL 5
AVDD12 F9 (SWITCHING) 1 2 3 4 5 RESET
L3028 L3003 PROTECT1
BLM21PG221SN1D BLM21PG221SN1D
VDDCLK G11 PROTECT3
C3139 R3110 R3111 C3075
0.1 C3076 C3066 C3068 C3069 C3070 56K 42.2K 0.022 CONTINUE
L3014 10 220/6.3V OPEN 10 0.1 R3109 R3103 DIGITAL 1
BLM21PG221SN1D 4.7K 1.8K VCOM-PWM
VCCQ18 H5
VCCQ18 J5 C3326 C3325 C3324 C3343 C3266 C3264 R3042 C3079 C3087 C3084 OE2
OPEN 10 10 10 100/4V 0.01 OPEN 100/4V 10 2.2
VCCQ18 M4 CONTINUE
DIGITAL 5
VCCQ18 T1 AL+3.3V
C3322 C3321 C3320 C3319 C3114 C3318
VCCQ18 M6 10 10 10 10 10 10 P-ON+5V
VCCQ18 N6 P-ON+3.3V(1)
VCCQ18 M7 C3140 C3141 C3142 C3143 C3144 C3145 AMP+24V
VCCQ18 M8 1 0.1 1 0.1 1 0.1 C3081 C3082 C3080 C3103 C3166 C3167 C3012 C3007 C3002 C3102 C3168 C3169 C3001
1 0.1 4.7 4.7 OPEN OPEN 0.1 1 4.7 4.7 OPEN OPEN 100/35V
IC3008 IC3001
MP2303ADNLFZ R3133 MP2303ADNLFZ
L3019 (DC-DC CONVERTER) C3083 (DC-DC CONVERTER) C3013 CONTINUE
BLM21PG221SN1D 10K C3109 C3110 DIGITAL 3
AVDD33 E10 C3091 0.015 C3092 0.047 10 OPEN GPY10
C3147 C3148 C3149 C3150 C3117 1000P 1 BST SS 8 1000P 1 BST SS 8
AVDD33 C2 0.1 0.1 1 0.1 0.1 CPU-RESET-N
AVDD33 C3 R3141 2 VIN EN 7 R3057 2 VIN EN 7 C3111 C3112 P-ON-H2
10 C3085 R3134 C3090 10 C3014 OPEN 10
AVDD33 E11 L3026 0.1 10K 1 0.1 DTV-ON-H2
BLM21PG221SN1D 3 SW COMP 6 3 SW COMP 6
2 AVDD33
AVDD33 E6
D6
C3151
L3029 C3154
BEAD 0.1
C3152
L3009
22uH
4 GND FB 5
R3137
6.8K
C3088
0.015 L3002
22uH
4 GND FB 5
R3001
39K
C3017
0.015
R3014
180
DTV-ON-H1
P-ON-H1
BACKLIGHT-ADJ
0.1 0.1 BACKLIGHT-SW
5.6K
C3089 D3001 C3094 C3067 C3097 C3096 R3149 C3099 C3065 C3093 D3002 C3020 C3101 C3021 R3004 C3059 C3060
100
100
100
100
100
R3008 100
R3053 100
L3016 OPEN OPEN 330/4V 330/4V 10 10 300 10 10 OPEN OPEN 220/6.3V 10 10 47K 10 10 VCOM-PWM
BLM21PG221SN1D
VCCQ33 G4 R3056 R3145 R3058 R3003
OPEN 8.2K OPEN 620
R3052
R3051
R3068
R3013
R3009
R3011
VCCQ33 F5 C3157 C3158 C3159 D3006 D3005
0.1 OPEN 0.1 EDZTE615.6B EDZTE615.6B TO POWER SUPPLY
VCCQ33 L12 CN3701 CBA CN632
R3143 R3002
VCCQ33 K13 16K 15K 1 VCOM-PWM
VCCQ33 J12 2 BACKLIGHT-SW
AVDD33 N11 3 BACKLIGHT-ADJ
C3026 C3025 C3022 C3105 C3170 C3171 R3018 D3008 IC3601 4 PROTECT3
0.1 1 4.7 4.7 OPEN OPEN 47K EDZTE6115B AKP2121AK
IC3003 (+3.3V REG.) 5 PROTECT1
VSS *B MP2303ADNLFZ
(DC-DC CONVERTER) C3028 6 P-ON-H1
VOUT
VIN
GND
0.047 R3019 R3063 Q3008 7 P-ON-H2
CE
NU
C3095 1 BST SS 8 10K 2SA1576UBTLQ
2.2K (SWITCHING)
*A:G5,G6,H6,J7,J11,J13,K6,K7, 1000P R3066 8 RESET
K11,L8,L9,M9,N9,P9,M11. 1K 1 2 3 4 5
*B:D2~D5,D12,E3~E5,E7,E9,F4,F6, R3054 2 VIN EN 7 9 OE2
0.1 C3042 C3018 R3067
F7,F10,F11,G7~G10,H7~H13,J6, 0.1 Q3009 OPEN 1K 10 GND
J8~10,K5,K8~K10,K12,L5~L7, 3 SW COMP 6 2SC4081UBTLQ R3010
L10,L11,P2,T8 R3005 (SWITCHING) 10K 11 AL+5V
6.8K C3601 C3602 C3603 C3015 C3016
4 GND FB 5 0.1 100/4V 1 10 0.1 12 GND
R3017 R3072
1 C3098 D3003
L3005
22uH
C3053 C3074
C3043
0.015
C3056 R3012 C3104 D3007

47K 100
C3044 C3011 C3046

13
14
15
AMP+24V
AMP+24V
GND
1000P
1000P
1000P
1000P
1000P
1000P
C3064 1000P
100P
C3003 100P
OPEN OPEN 220/6.3V 10 10 51K 10 EDZTE616.8B 0.1 1 1 16 P-ON+24V
R3055 R3007
OPEN 2.4K 17 P-ON+24V
C3055
C3063
C3062
C3048
C3008
C3004
C3006
18 GND
R3006 C3146 C3138 C3153
10K 0.1 1 1 19 GND
S T U V W X
10-10 FL11.4SCD4
1 NOTE:
CONTINUE
DIGITAL 4
AL+3.3V
P-ON+5V
P-ON+3.3V(1) R3183 *1
OPEN Q3010 IC3005(5/6)
AMP+24V OPEN R8A05011BG-U0
C3557 C3558 DIGITAL SIGNAL PROCESS
OPEN OPEN /MAIN MICRO CONTROLLER
CONTINUE
DIGITAL 3 R3185
LED1 OPEN R3312 10K
D13 NU
4 AUDIO-MUTE
REMOTE
TO IR SENSOR
R3184
OPEN
R3186
OPEN
CBA UNIT CN4052 CN3102

GND 1 R3552 C3554
100 0.1
REMOTE 2
AL+3.3V 3 C3553
R3317 10K
R3318 10K
R3319 10K
100P
P-ON+5V 4 R3551 R3555
100 OPEN
LED1 5
KEY-IN1 6
R3553
1000P
1000P
LIGHT 7 100
OPEN
OPEN
OPEN
OPEN
C3556 C3559 Q3501
100P 1000P 2SC4081UBTLQ
(NO CONNECTION) CN3103
C3222
C3221
C3233
R3500
C3232
R3499
P-ON+5V 1 (LED DRIVE)
GND 2 C3555
1000P D3107
1SS400
TO FUNCTION C3323 1000P
CBA UNIT CN4001 CN3101
GND 1 R3554 R3340 10K
0 R3313 100 NU D11
KEY-IN1 2 A15 KEY-IN1 C3219 10
R3314 22 NU D7
C3552 B13 PROTECT3 C3220 10
3 CONTINUE
DIGITAL 4
RESET
1000P
C3231 0.22
R3315
R3316
R3341
OPEN
22
0
A13
C13
C12
LIGHT-SENS
PROTECT1
LPF
NU
NU
NU
NU
C6
C5
B6
A6
C3216 10
PROTECT1
PROTECT3 C3328
OPEN
CONTINUE
DIGITAL 2 R3335 100 C3217 10
AUDIO(L)-IN A8 CONTINUE
R3336 100 C3218 10 DIGITAL 2
AUDIO(R)-IN B8 AUDIO R3209 100
R3224 0 C3223 1 I/F N10 SPDIF
B7
R3225 0 C3224 1
A7
R3322
2.7K TO DIGITAL TO DIGITAL
MAIN 2 MAIN 6
R3501 C3227 C3804 IC3005(2/6) IC3005(6/6)
100K 2200P 1 CONTINUE
R3191 100 DIGITAL 3
C3814 10 C3815 10 CPU-RESET-N J15 CPU-RESET-N
D3111 IC3009
2 R3810
10K
C3813 1
30 29 28 27 26 25 24 23 22 21
R3809 27K OPEN R3178
10K
PST8420UR
(RESET)
1 GND OUT 4
C3116
R3182
4.7K
C3120
D3109
1SS400
BL-SW
VREFF
PROT
AVCC
ROSC
GND
GND
GND
GND
GND
NU
OPEN 0.01 D3110

R3817 C3816 2 VDD CD 3 1SS400
OPEN 10 D3108 C3106 C3252
31 GND CBIAS 20 EDZTE615.6B 0.1 OPEN
C3805 C3113
1 0.033
32 19
R3325 R3502 C3229
2.7K 100K 2200P 33 18 R3808 Q3804
OPEN R3821 2SA1576UBTLQ
10K (SWITCHING)
34 CONTROL 17
R3805 R3812 LOGIC C3832 R3804
39K 33K C3817 R3807 R3806 0.1 R3822 R3820 22K
0.1 0 35 GND GND 16 OPEN 100K 22K
R3818
36 GND GND 15 R3819 22K
10K
37 VDD PWM PWM VDD 14 C3819
GENE. GENE. 100/35V
C3823 C3829 Q3803
100/35V OPEN 38 VDD VDD 13 2SC4081UBTLQ C3830
(SWITCHING) L3801 100/35V CN3801
22uH SP3801
R3826 Q3802 39 12 1 SP(L)
10K 2SC4081UBTLQ D3801 C3807 C3822 C3828 SPEAKER
CRZ33 R3803 0.1 0.1 R3828 1000P 2 SP-GND L-CH
(AUDIO-MUTE) 40 11 22 OPEN
C3802 C3818
DVDD1
R3811 1000P 100/35V R3824
1
GND
HB2
GND
GND
GND
GND
GND
HB1
GND
10K OPEN
IC3801
R2A15122FP 1 2 3 4 5 6 7 8 9 10 L3802 C3806 CN3802
(AUDIO AMP) 22uH 100/35V SP3802
C3809 1 SP(R)
D3802 SPEAKER
R3830 0.1 CRZ33 R3802 C3808 C3821 C3803 2 SP-GND R-CH
0 C3810 C3825 22 0.1 0.1 1000P
0.1 10 C3801
1000P R3823
OPEN
Q3805 C3833 R3825 R3827
C3824 C3812 C3826 C3811 OPEN OPEN OPEN OPEN
100/35V 0.1 100/35V 0.1
Y Z AA BB CC DD
10-11 FL11.4SCD5
1 NOTE:
CONTINUE
DIGITAL 4 L3046 HDMI-
BLM21PG221SN1D JK3002 CONNECTOR-2
P-ON+3.3V
C3316 C3300 C3301 C3302 C3303 C3304 1 TMDS-D2(+)
AL+3.3V 10 0.1 OPEN 0.1 OPEN 0.1 2 D-SHIELD0
P-ON+3.3V(1)
3 TMDS-D2(-)
C3305 C3306 C3307 C3308 C3309 4 TMDS-D1(+)
OPEN 0.1 OPEN 0.1 OPEN
5 D-SHIELD1
6 TMDS-D1(-)
C3310 C3311 C3312 C3313 C3314 7 TMDS-D0(+)
0.1 OPEN OPEN OPEN 0.1
4 *1
IC3005(6/6)
R8A05011BG-U0
DIGITAL SIGNAL PROCESS
C3315
OPEN
C3331
0.1
C3332
OPEN
C3333
0.1
C3334
OPEN
8
9
10
11
D-SHIELD2
TMDS-D0(-)
TMDS-CLOCK(+)
C-SHIELD0
/MAIN MICRO CONTROLLER Q3014
2SK3018T106 R3405 12 TMDS-CLOCK(-)
(BUFFER) 100
13 HDMI-CEC
TO DIGITAL TO DIGITAL R3415 14 NU
MAIN 2 MAIN 5 82K
IC3005(2/6) IC3005(5/6) D3057 R3486 15 HDMI-CLOCK
RB751S-40 4.64K 16 HDMI-DATA
VIDEO AUDIO IC3018 R3275 R3278 17 GND
DECODER DECODER 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 BU16029KV-E2 47K 47K
R3237 (HDMI SW) 18 +5V
GND
VCC
GND
VCC
GND
NU
27K C3262 R3411 R3370 19 HOT PLUG DETECT
HDMI-CEC B15 1 2.7K 1K
17 HOT-PLUG- 64 R3371
DETECT3 R3412 OPEN
18 63 OPEN
Q3030
B1 R3489 19 VCC 62 R3408 2SC4081UBTLQ
10K 1K (SWITCHING)
A1 D3067
20 VCC 61 1SS400 R3386
B2 10K
A2 21 60
HDMI
I/F B3
22 GND 59
A3
B4 23 GND 58
A4
3 24
25 VCC
26
HDMI SW 57
56
VCC 55
27 54
R3488 R3487
4.7K 4.7K
28 GND 53
HDMI1-SCL C16 29 SCL-SINK 52
HDMI1-SDA C15 30 SDA-SINK 51
HDMI1-HPD D14 31 HOT-PLUG-
DETECT-SINK
HOT-PLUG- 50
DETECT2
R3508
22
HOT-PLUG-
HDMI-SEL0 G3 32 HDMI-
SEL0 NU 49
DETECT1
R3496
HDMI-
4.7K
SEL1
HDMI-SEL1 F1
VCC
GND
VCC
NU
R3509 R3497
22 4.7K 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
HDMI-
R3236 C3185 R3270 C3187 JK3003 CONNECTOR-1
560 0.01 2.2K 2.2 1 TMDS-D2(+)
EXT-RES C4 C3186 2 D-SHIELD0
2 PLL-XFC-A B5
PLL-XFC-P A5
4700P
R3271 C3188
3K 2200P
3
4
5
TMDS-D2(-)
TMDS-D1(+)
D-SHIELD1
6 TMDS-D1(-)
7 TMDS-D0(+)
8 D-SHIELD2
PWR M12 9 TMDS-D0(-)
R3510 22 10 TMDS-CLOCK(+)
M32-TCK E1 11 C-SHIELD0
12 TMDS-CLOCK(-)
HDMI-SDA F14 13 HDMI-CEC
HDMI-SCL G14 14 NU
15 HDMI-CLOCK
16 HDMI-DATA
R3293 R3302 D3066 R3273 R3276 17 GND
10K 10K 1SS400 47K 47K
18 +5V
R3301 R3372 19 HOT PLUG DETECT
33K C3261 R3410 1K
1 2.7K
R3373
C3213 R3413 OPEN
IC3011 0.1 OPEN
BU9883FV-WE2
(HDMI SERIAL EEPROM)
Q3031
1 VCC1 VCC2 16 R3407 2SC4081UBTLQ
C3190 1K (SWITCHING)
1 2 SCL1
3 SDA1
4 WPB
SCL2 15
SDA2 14
NU 13
0.1
R3383
10K
R3523 C3192 0.1 CONTINUE

R3192 R3193 10K 5 VCC-OUT GND 12 DIGITAL 2
4.7K 4.7K R3282 PC-SDA
100
R3281 6 SDA0 SDA3 11 PC-SCL
100
CONTINUE 7 SCL0 SCL3 10 PC+5V
DIGITAL 2
HDMI-33V 8 VCC0 VCC3 9
C3271
C3272
OPEN OPEN C3191
0.1
C3212
0.1 DIGITAL MAIN CBA UNIT
EE FF GG HH II JJ
10-12 FL11.4SCD6
Power Supply CBA Top View [TYPE A]
Because a hot chassis ground is present in the power supply
circuit, an isolation transformer must be used when repairing.
CAUTION ! Also, in order to have the ability to increase the input slowly,
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. when troubleshooting this type of power supply circuit,
If Main Fuse (F601) is blown , check to see that all components in the power supply CAUTION ! : For continued protection against risk of fire,
a variable isolation transformer is required.
circuit are not defective before you connect the AC plug to the AC power supply. replace only with same type 4 A, 125V fuse.
4A/125V ATTENTION : Utiliser un fusible de rechange de mme type de 4A, 125V. NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
CN1100 CN1101 CN1102
C1104 C1110 C1108 C1114
4
BA17F1F0102 2 TOOL NO.
1 2 3 4 5 6 7 8 9 10
C1106
C1112
C7A3 A3
PROT6
IS6
PROT3
IS3
IS1
J1003 SW2
J1005
J1004
SW2
SW2
SW2
PROT1
J1164
J1162
J1163
PROT4
J1154
J1153
IS4
J1169
J1161
C1701
J1033
J1152
GND T1102
J1002
J1006
T1100 T1101
1
R1704
2
GND
J1157 J1007
GND SW2
C1709
C1700
IS2
R1709
SW2
IS4
J1008
PROT4
IS1
J1132
GND
SW2
SW2
PROT1
J1156
J1019
J1009
GND
J1017
PROT6
J1016
PROT3
J1155
J1015
IS3
GND
J1018
J1012
R1146
R1106
CN200
R1130
R1150
INV+24V
J1011
INV+24V
INV+24V
J1010
INV+24V
J1047
J1070
J1149
11
10
J1130
J1024 J1020
A17F1MPW GND
J1014
J1013
D1705
PROT5
D1703
J1124
GND
D1700
E234498
D1702
D1707
J1032
D1704
J1022
R1143
R1103
VS2 PROT6
J1025
J1072
D1706
D1701
GND
VS6
LN1
R1148
J1026
J1027
INV+24V
INV+24V
INV+24V
INV+24V
R1145
J1165
HN1
J1168
J1167
J1166
J1029
R1118
R1115
LN1 J1021
R1147
R1127
J1030
VSEN
J1028
J1049
3 COLD
J1048
J1041
GND
PROT4
PROT1
PROT3
BL-SW
LN1
IS5
LN2
HN2
SW2
HN1
C649 J1043 C1206
J1151
J1039
J1037
J1038
J1036
J1031
J1040
J1035
INV-GND
VSEN
J1046
J1034 J1069
J1045 J1059 DC-12V
SW2
STB GND GND
GND
GND
GND
GND
GND
J1094
J1058
J1023
J1159
J1092
INV-GND
D1301
J1042
J1050
D1300
NH1 C1302
ISEN
VSEN
J1053
J1054
J1055
C611
NH1
C604 J1052 PROT2
HOT
C603
C612
J1056 D1201
JS1200 PROT
DC-12V J1064
D602 DUTY
PROT J1057 J1062
REG-7.5V
J1061
J1060
LN1
REG-7.5V
J1150
SW1
J1051
PROT5
C648
D603
D1203
D600
C1304
J1071
J1067
PROT
D601 DUTY
J1001
D1200
GND
5
C602 30
GND
D612 D1202 R1
J1170
GND
J1158
J1063
C641
J1073
2
D644 GND
R61
VLO
J1068
GND
D648
R602
D633
37
J1066
46
GND
D6
D6
C632
J1074
Q1202-B
J1076
C610
GND
J1075
BL-ADJ
D201
3
START
D606
R61
PANEL+15.8V
J1079
J1078
3
C61
D610
24V
PANEL24V
P-ON+24V
P-ON+24V
C607 PROTECT3
C203
R265
J1077
J1083
J1090
C208
J1080 BL-ADJ
R611
L601
R255
R608 C614
J1084
GND
J1081
J1082
R203
GND
J1086
C601 D611 D200 J1065
C638
P-ON-H1
GND
R256
D604
T600 J1088
2 GND
J1087
D207
D208
Q600-S
J1091
P-ON-H1
D202
Q600
J1089
C215
C229
R209
PROTECT1
R258
R259
R257
J1093
R211
R235
R246
R240
D613
J1095
C637
D206
JS660
D205
D607
Q601
C227
R606
R233
D222
D63
D212
J1098
R609
L600
4
D221 C214
Q213-C
D645
BC602
BC601
R263
J1099
R234
-7.5V
J1102
J1101
DRIVE
J1100
C631
AMP24V
J1105
J1104
+17V
J1103
P-ON+24V
P-ON+24V
+36V PROTECT1
FB
Q221 J200
J1096
J1097
C639 Q222 C220 VCOM2
C644
J1106 +16V
CN600
J1110
J1107
GND
P-ON+24V
AMP24V
D651
AMP24V
D641
GND
J1111
R607
R605
R239
J1112
P-ON+24V
GND
J1114
PANEL15.8V
PANEL-6V
GND
GND
J1109
PROTECT1
J1108
J1118
J1113
D650
J1115
D609
D605
D659
C600
D658
C228
HOT
VCOM-PWM
Q207-B J1119
J1116
J1117
D210
R610
IC601
D655
C217
J1120
J1122
GND
OVL
SA601
J1123 PANEL-6V
J1121
D638
COLD
D657
D636
R268
CN601
R245
R657 J1125 PANEL+3.3V
R662
R656
C647
J1126
R601
GND
C230
1 D652
J1127
D639
R266
J1139
GND
Q636
F601
C675
J1131 P-ON-H2 GND
4A/125V
D654
D663
R634
R633
J1044
R659
R660
R658
GND
J1135 OVL C226
D631
P-ON-H2 J1129 J1133
PROTECT1
D211
J1138
R636
J1141 GND J1137 J1136 PANEL+3.3V

J1085 P-ON-H2
GND
R635
R649
J1171 ALL5V
J1142
D632
ALL5V
BL-ADJ
J1128
FH601 GND
FH602
D656
GND
J1144
VCOM-PWM
GND 1 J1143 D635 PROTECT3
J1134
JS200
J1145
RISK OF FIRE-
J1147
BL-SW
J1146
GND
J1140 19 ALL5V
C646
P-ON-H2
J1148
REPLACE FUSE AS MARKED 18
CN632
2
OE2
A B C D E F
10-13 BA17F1F01022
BA17F1F01022
Also, in order to have the ability to increase the input slowly,

when troubleshooting this type of power supply circuit,

1
4
C612
CN600
D603
J1157
J1169
GND
GND
J1132
CN601
GND
C1106
R1111
R1110
R1109 C1119
D600
C1107
C600
COLD
IS2 J1009
C601
FH601
L601
A
F601
D602
R1146
4A/125V
NOTE:
R1106
CN1100
HOT
R611
L600
R1107
D601
J1022
D1506
D611
FH602
R1108
T1100
VS2
R1105
SA601
C611
R601
R1104
C603
R1143
R608
C1100 D604
R1103
C1101 R609
C606
Q601
D1503 C609
R600
C608
R1102 R1101 C605 R606 J1100
START J1077 R605
R602
R610
C1105 R1100 D610 DRIVE
J1012 J1091 D607
J1103
J1161 C1118
IS1 FB
IS1 J1018 Q600-S
D609
J1162 PROT1 J1012 R604 D605
PROT1 R636
R603
Q600 R607
D606
BC602 R637
C602
J1142
C1104
IC601
R1704 GND
BC601
D1703
B
R635
HOT
C1705 D613
C1704 D654 R649
R645
C607
R1703
2
R61
Q1701
J1007
J1008
3 Q634
R1702 R61
R647
D631
R651
C614
C604
3
SW2
C61
SW2
D1702 C645
J1027
R652
HN1
D1701 Q631 R655

J1134
D612
C610
C1703 GND
T600
R632
R1701
Q635
Q1700
R1700
P-ON-H2
J1140
R644
D1700
J1092 R654
C1702 GND
J1094
J1025
LN1
GND J1127
C1110
C1111 J1159
COLD
GND
C
R1121 J1058 GND
C1121 GND
J1023 C641
J1163 PROT4 J1015 GND
PROT4 R1122 J1078
R1123 24V
IS4 D1504 D640
10-14
J1164 J1017 R650
D644 D660
IS4
C1700 J1028
R1120
VSEN D645 D643
D648
C647
R1148 D649
R1119
CN1101
R1118
C639
D1507 J1030
D642
J1135
D650
C1102
R1116 R1115 J1126
C1103 37 C644
19
18
R1117 D6 GND
R1145
P-ON-H2
R663
J1144
GND J1141
J1047 J1168 C637 4 J1122 C634
D63 C631
INV+24V INV+24V R631 OVL
R642
J1171
J1070 J1167
T1101
C648
GND
INV+24V INV+24V
GND
J1131
J1149 J1166 C231
OVL
C635
Q633
INV+24V INV+24V
J1130 J1165
46
C649
INV+24V INV+24V D6 R643

J1053 R1301 GND
ISEN J1116
C1120 R1112 J1054 J1150 GND J1117 R664
VSEN R1226 REG-7.5V
C1109 R1113 R1302 C638 C633 D639
SW2 J1003 HN1 J1039 AMP24V J1109
R1225 Q1204 C632
J1004 AMP24V J1108 D663
1
R1114 PROT4 J1040 R1227 R1300 R641 Q632
2
P-ON+24V J1113
CN632
SW2 J1104
C1709
C1500 R269 D638 R634
J1085
PROT3 J1035 R638
AMP24V J1114
JS1200
PROT
R1500 J1001 J1086

IS3 J1033 Q1203 R1228 GND D657 R633
J1143
ALL5V
Q636
PROT1 P-ON+24V
D
J1013 J1151 R1229 J1110
IS3 GND
D655
P-ON-H2
PROT3 JS660 GND
R657
J1014 R1503 J1067 R659
J1101
D656
C1108
PROT3 J1152 PROT +36V

C1710 R1502 D1502 R660
J1029
LN1
R1501 PROT D1500 J1074 D659

R262
J1052
D661
J1062 J1057
C1708 GND J1096 R658
4A/125V
R1512 R1511 R662

D1707 P-ON+24V
R1507 R1510 C636
PROT5
R1509 J1097 R656
J1137
ALL5V
VSEN
J1043
R1709 D662 P-ON+24V D658
J1139
R1506
Q1301
J1112
P-ON-H2
D636
R1708 P-ON+24V J1081
PROT2
Q208
D1501
R1505
Q1703
BA17F1F0102 2
C1707 R1508 P-ON+24V J1082 GND

R1504 R1308
R1310 D641 R229 R230 C646
R1307
Q1303
J1099
-7.5V
R1306
J1118
SW2 R232
J1010 R1707 R1220
D635
D1706 GND J1087 R231
J1056
H.V. CAUTION
Q207-B
LN2 J1037 C1311
SW2
J1011 D651
HN2 J1038 R1304 R1303
C226
R251
R235
R233
J1050
Q207
NH1
SW2 J1036 C1301 Q210
D1705 R252 J1102
DC-12V
D1201
C217
R228
J1136
ALL5V
C229 +17V
J1051 C1209
J1129
C1706 SW1 C225 C216
Q1702
R1706 R1222 R254 R227

IC202
GND
R1705 J1055 R234 J1145
R1223 Q211
D1202
NH1 R255 R261 GND

Q222
R244
J1133
J1061 J1066
REG-7.5V
PANEL+3.3V
D1704 C223
D1200
D208 R260 R226
J1046 GND
C1701 SW2 C1208 Q212 R243
J1041 R1221 J1158
Power Supply CBA Bottom View [TYPE A]
D207 C224
GND R1516 Q213
LN1 J1107 R245

C1114
J1031 R1216
C230
R256 R258 GND
C1205 J1073
E
INV-GND J1060
J1042 LN1 R265
R259 R267 VCOM-PWM
J1098
Q213-C
J1153 INV-GND VLO
D200
C227 J1146
C203
PROT6 R1204 C1300
R257
C228
J1154 J1016 C1204 Q214
IS6 IC1200 R1213
J1105
PROT6 R200 C675 J1147
1
J1045
C1213
24
PROTECT1
STB
J1032
J1005 R1133 R1514 BL-SW
PROT6
R1205 C204
D202
SW2 C1201 R1515 R1513 R248 R201 D206 BL-ADJ J1148
J1106
C1123 R202 J1115 R266
SW2 R1202 C1501
J1006 C1115 R249 J1089
12
13
C1502 R223 D205 R263 PANEL-6V R268 D632
R1135 R1134 PROTECT1 PROTECT1 J1121 J1138
+16V
R1203 R1214 C1210 C1203
D212
J1019 J1026 C1202 PROTECT1
C205
PANEL24V
VS6 Q200 R246
R239
J1080
C1207
C1206
C1214
D652
J1063
Q221
R1130 R1209 Q201 R205
GND
R240 D222 R264
D1505
DUTY
D210
JS200
J1071
OE2
R1150 GND J1068 Q206 C222
J1059
C206 R236
D1508 R1147 J1093
T1102
R247
DUTY
J1064
R203
C1302
J1125
R1131 R204 R237
J1123
Q1201 P-ON-H1 C221
DC-12V
R1132 R1201 R1212 C207
R1127 R206
R238
PROTECT3
R253
J1128
R1129 R1128 R1215
C1117 R1208 C208 R222
R1124
C220
J1075 R270
PANEL+3.3V
C1113
J1111
PANEL-6V
C1211
PANEL15.8V
BL-ADJ R209
C1122
D221
J1090 C210
R1125
CN1102
C1212 PANEL+15.8V Q202

C1116 R1200 R1206
J1076 R212 R213 D211
J1021
IS5
C1303
D1301
J1119
R1126 C209 R241
GND
Q1202-B
D1203 R210
Q1300 R207
J1024
J1155
PROT5
J1156
5
R214 C212
30
R1309 R1207 R242
C1305
R1
R208 C211 J1044
C1200
Q203
J1088
C1304 J1095 GND
R218
J1084 R217
8
J1124
1
Q204
P-ON-H1
GND
Q1202
D1300
F
D633 R211
R216
GND
GND
GND
IC200
4
C200
J200
5
R225 R220 R215
J1072
J1049
GND
GND
R221
J1002 R219 J1120
GND R224 VCOM-PWM
VCOM2
C1112
D201
J1034
J1170
C213
GND
PROTECT3
GND
CN200 Q205
J1079
1
BL-ADJ
C215
J1083
11
C214
C218
2 10
J1065
J1020
J1048
BL-SW
GND
GND
J1069
GND
C201
C202
CAUTION !
Power Supply CBA Top View [TYPE B]
CAUTION ! Also, in order to have the ability to increase the input slowly,
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. when troubleshooting this type of power supply circuit,
If Main Fuse (F601) is blown , check to see that all components in the power supply CAUTION ! : For continued protection against risk of fire,
circuit are not defective before you connect the AC plug to the AC power supply. replace only with same type 4 A, 125V fuse.
4A/125V ATTENTION : Utiliser un fusible de rechange de mme type de 4A, 125V. NOTE:
CN1100 CN1101 CN1102
C1104 C1110 C1108 C1114
4
BA17F8F0102 2 TOOL NO.
1 2 3 4 5 6 7 8 9 10
C1106
C1112
C7A3 A3
PROT6
IS6
PROT3
IS3
IS1
J1003 SW2
J1005
J1004
SW2
SW2
SW2
PROT1
J1164
J1162
J1163
PROT4
J1154
J1153
IS4
J1169
J1161
C1701
J1033
J1152
GND T1102
J1002
J1006
T1100 T1101
1
R1704
2
GND
J1157 J1007
GND SW2
C1700
C1709
IS2
R1709
SW2
IS4
J1008
PROT4
IS1
J1132
GND
SW2
SW2
PROT1
J1156
J1019
J1009
GND
J1017
PROT6
J1016
PROT3
J1155
J1015
IS3
GND
J1018
J1012
R1146
R1106
CN200
R1130
R1150
INV+24V
J1011
INV+24V
INV+24V
J1010
INV+24V
J1047
J1070
J1149
11
10
J1130
J1024 J1020
A17F8MPW GND
J1014
T
J1013
D1705
PROT5
D1703
J1124
GND
D1700
D1702
E234498
D1707
J1032
D1704
J1022
R1143
R1103
VS2 PROT6
J1025
J1072
D1706
D1701
GND
VS6
LN1
R1148
J1026
J1027
INV+24V
INV+24V
INV+24V
INV+24V
R1145
J1165
HN1
J1168
J1167
J1166
J1029
R1118
R1115
LN1 J1021
R1147
R1127
J1030
VSEN
J1028
J1049
3 COLD
J1048
J1041
GND
PROT4
PROT1
PROT3
BL-SW
LN1
IS5
LN2
HN2
SW2
HN1
C649 J1043 C1206
J1151
J1039
J1037
J1038
J1036
J1031
J1040
J1035
INV-GND
VSEN
J1046
J1034 J1069
J1045
SW2
J1059 DC-12V GND GND
STB
GND
GND
GND
GND
GND
J1094
J1058
J1023
J1159
J1092
INV-GND
D1301
J1042
J1050
D1300
NH1 C1302
ISEN
VSEN
J1053
J1054
J1055
C611
NH1
C604 J1052 PROT2
HOT
C603
C612
J1056 D1201
JS1200 PROT
DC-12V J1064
D602 DUTY
PROT J1057 J1062
REG-7.5V
J1061
J1060
LN1
REG-7.5V
J1150
SW1
J1051
PROT5
C648
D603
D1203
D600
C1304
J1071
J1067
PROT
D601 DUTY
J1001
D1200
GND
5
C602 30
GND
D612 D1202 R1
J1170
GND
J1158
J1063
C641
2
J1073
GND
D644
R61
VLO
J1068
GND
D648
R602
D633
37
J1066
46
GND
D6
D6
C632
J1074
Q1202-B
J1076
C610
GND
J1075
BL-ADJ
3
D201
START
D606
R61
PANEL+15.8V
J1079
J1078
3
D610
C61
24V
PANEL24V
P-ON+24V
P-ON+24V
C607 PROTECT3
C203
R265
J1077
J1083
J1090
C208
J1080 BL-ADJ
R611
L601
R255
R608
C614
J1084
GND
J1081
J1082
R203
GND
J1086
C601 D611 D200 J1065
C638
P-ON-H1
GND
R256
D604
T600 J1088
2 GND
J1087
D207
D208
Q600-S
J1091
P-ON-H1
D202
Q600
J1089
C215
C229
R209
PROTECT1
R258
R259
R257
J1093
R211
R235
R246
R240
D613
J1095
C637
D206
JS660
D205
D607
Q601
C227
R606
R233
D222
D63
D212
J1098
R609
L600
4
D221 C214
Q213-C
D645
BC602
BC601
R263
J1099
R234
-7.5V
J1102
J1101
DRIVE
J1100
C631
AMP24V
J1104
J1105
+17V
J1103
P-ON+24V
P-ON+24V
+36V
PROTECT1
FB
Q221 J200
J1096
J1097
C639 Q222 C220 VCOM2
C644
J1106 +16V
CN600
J1110
J1107
GND
P-ON+24V
AMP24V
D651
AMP24V
D641
GND
J1111
R607
R605
R239
J1112
P-ON+24V
GND
J1114
PANEL15.8V
PANEL-6V
GND
GND
J1109
PROTECT1
J1108
J1118
J1113
D650
J1115
D609
D605
D659
C600
D658
C228
HOT
VCOM-PWM
Q207-B J1119
J1116
J1117
D210
R610
IC601
D655
C217
J1120
J1122
GND
OVL
SA601
J1123 PANEL-6V
J1121
D638
COLD
D657
D636
R268
CN601
R245
R657 J1125 PANEL+3.3V
R662
R656
C647
J1126
R601
GND
C230
1 D652
J1127
D639
R266
J1139
GND
Q636
F601
C675
J1131 P-ON-H2 GND
D654
D663
4A/125V
R634
R633
J1044
R659
R660
R658
GND
J1135 OVL C226
D631
P-ON-H2 J1129 J1133
PROTECT1
D211
J1138
R636
J1141 GND J1137 J1136 PANEL+3.3V

J1085 P-ON-H2
GND
R635
R649
J1171 ALL5V
J1142
D632
ALL5V
BL-ADJ
J1128
FH601 GND
FH602
GND
D656
VCOM-PWM
J1144 GND 1 J1143 D635 PROTECT3
J1134
JS200
J1145
J1147
BL-SW
RISK OF FIRE-
J1146
GND
J1140 19 ALL5V
C646
P-ON-H2
J1148
REPLACE FUSE AS MARKED 18
CN632
2
OE2
A B C D E F
10-15 BA17F8F01022
BA17F8F01022
Also, in order to have the ability to increase the input slowly,

when troubleshooting this type of power supply circuit,

1
4
C612
CN600
D603
J1157
J1169
GND
GND
J1132
CN601
GND
C1106
R1111
R1110
R1109 C1119
D600
C1107
C600
COLD
IS2 J1009
C601
FH601
L601
A
F601
D602
R1146
4A/125V
R1106
CN1100
HOT
R611
L600
R1107
D601
J1022
D1506
NOTE:
D611
FH602
R1108
T1100
VS2
R1105
SA601
C611
R601
R1104
C603
R1143
R608
C1100 D604
R1103
C1101 R609
C606
Q601
D1503 C609
R600
C608
R1102 R1101 C605 R606 J1100
START J1077 R605
R602
R610
C1105 R1100 D610 DRIVE
J1091 D607 J1103
IS1 J1161 C1118
IS1 J1018 Q600-S FB
D609
J1162 PROT1 J1012 R604 D605
PROT1 R636
R603
Q600 R607
D606
BC602 R637
C602
J1142
C1104
IC601
R1704 GND
BC601
D1703 B
HOT
C1705 D613 R635

C1704 D654 R649
R645
C607
R1703
2
R61
Q1701
J1007
J1008
3 Q634
R1702 R61
R647
D631
R651
C614
C604
3
SW2
C61
SW2
D1702 C645
J1027
R652
HN1
D1701 Q631 R655
J1134
D612
C610
C1703 GND
T600
R632
R1701
Q635
Q1700
R1700
P-ON-H2
J1140
R644
D1700
J1092 R654
C1702 GND
J1094
J1025
LN1
GND
C1110
J1127
J1159
COLD
C1111
GND
C
R1121 J1058 GND
C1121 GND
J1023 C641
J1163 PROT4 J1015 GND
R1122 J1078
PROT4
R1123 24V
J1164 IS4 J1017 D1504 D640
R650 D660
D644
IS4
C1700 J1028
R1120
VSEN D645 D643
D648
C647
R1148 D649
CN1101
R1119
R1118
C639
D1507 J1030
D642
10-16
J1135
D650
C1102
R1116 R1115 J1126
C1103 37 C644
19
18
R1117 D6 GND
R1145
P-ON-H2
R663
J1144
GND J1141
J1047 J1168 C637 4 J1122 C634
D63 C631
INV+24V INV+24V R631 OVL
R642
J1171
J1070 J1167
T1101
C648
GND
INV+24V INV+24V
GND
J1131
J1149 J1166 C231
OVL
C635
Q633
INV+24V INV+24V
J1130 J1165
46
C649
INV+24V INV+24V D6 R643

J1053 R1301 GND
ISEN J1116
C1120 R1112 J1054 J1150 GND J1117 R664
VSEN R1226 REG-7.5V
C1109 R1113 R1302 C638 C633 D639
SW2 J1003 HN1 J1039 AMP24V J1109
R1225 Q1204 C632
J1004 AMP24V J1108 D663
1
R1114 PROT4 J1040 R1227 R1300 R641 Q632
2
P-ON+24V J1113
CN632
SW2 J1104
C1709
C1500 R269 D638 R634
J1085
PROT3 J1035 R638
AMP24V J1114
JS1200
PROT
IS3 J1033 R1500 J1001 J1086

Q1203 R1228 GND D657 R633
J1143
ALL5V
Q636
PROT1 P-ON+24V
D
J1013 J1151 R1229 J1110
IS3 GND
D655
P-ON-H2
PROT3 JS660 GND
R657
J1014 R1503 J1067 R659
J1101
D656
C1108
PROT3 J1152 PROT +36V

C1710 R1502 D1502 R660
J1029
LN1
D659
PROT D1500
R1501 J1074 R262

J1052
D661
J1062 J1057
C1708 GND J1096 R658

R1512 R1511 R662
D1707 P-ON+24V
R1507 R1510 C636
PROT5
R1509 J1097 R656
J1137
ALL5V
VSEN
J1043
R1709 D662 P-ON+24V D658
J1139
R1506
Q1301
J1112
P-ON-H2
D636
R1708 P-ON+24V J1081
PROT2
Q208
D1501
R1505
Q1703
BA17F8F0102 2
C1707 R1508 P-ON+24V J1082 GND

R1504 R1308
R1310 D641 R229 R230 C646
4A/125V
R1307
Q1303
J1099
-7.5V
R1306
J1118
SW2 R232
J1010 R1707 R1220
D635
D1706 GND J1087 R231
J1056
H.V. CAUTION
Q207-B
LN2 J1037 C1311
SW2
J1011 D651
HN2 J1038 R1304 R1303
C226
R251
R235
R233
J1050 Q207
NH1
SW2 J1036 C1301 Q210
D1705 J1102
DC-12V
R252
D1201
C217
R228
J1136
ALL5V
C229 +17V
J1051 C1209
J1129
C1706 SW1 C225 C216
Q1702
R1706 R1222 R254 R227
IC202
GND
R1705 J1055 R234 J1145
R1223 Q211
D1202
NH1 R255 R261 GND
Q222
R244
J1133
J1061 J1066
REG-7.5V
PANEL+3.3V
D1704
D1200
D208 R260 R226 C223
J1046 GND
C1701 SW2 C1208 Q212 R243
J1041 R1221 J1158 D207 C224
GND
LN1 R1516 Q213 J1107 R245

C1114
J1031 R1216
C230
R256 R258 GND
C1205
E
INV-GND J1060 J1073
J1042 LN1 R265
R259 R267 VCOM-PWM
J1098
Q213-C
J1153 INV-GND VLO
D200
C227 J1146
C203
PROT6 R1204 C1300
R257
C228
J1154 J1016 C1204 Q214
IS6 IC1200 R1213
J1105
PROT6 R200 C675 J1147
1
J1045
C1213
24
PROTECT1
STB
J1032
J1005 R1133 R1514 BL-SW
PROT6
R1205 C204
D202
Power Supply CBA Bottom View [TYPE B]
SW2 C1201 R1515 R1513 R248 R201 D206 BL-ADJ J1148
J1106
C1123 R202 J1115 R266
SW2 R1202 C1501
J1006 C1115 R249 J1089
12
13
C1502 R223 D205 R263 PANEL-6V R268 D632
R1135 R1134 PROTECT1 PROTECT1 J1121
+16V
R1203 R1214 C1210 C1203 J1138
D212
J1019 J1026 C1202 PROTECT1
C205
PANEL24V
VS6 Q200 R246
R239
J1080
C1207
C1206
C1214
D652
J1063
Q221
R1130 R1209 Q201 R205
GND
R240 D222 R264
D1505
DUTY
D210
JS200
J1071
OE2
R1150 GND J1068 Q206 C222
J1059
C206 R236
D1508 R1147 J1093
T1102 R247
DUTY
J1064
R203
C1302
J1125
R204 R237
J1123
R1131 Q1201 P-ON-H1 C221
DC-12V
R1132 R1201 R1212 C207
R1127 R206
PROTECT3
R253 R238
J1128
R1129 R1128 R1215
C1117 R1208 C208 R222
R1124
C220
J1075 R270
PANEL+3.3V
C1113
J1111
PANEL-6V
C1211
PANEL15.8V
BL-ADJ R209
C1122
D221
J1090 C210
CN1102
R1125 C1212 PANEL+15.8V Q202

C1116 R1200 R1206
J1076 R212 R213 D211
J1021
IS5
C1303
D1301
J1119
R1126 C209
GND
Q1202-B R241
D1203 R210
Q1300 R207
J1024
J1155
PROT5
J1156
5
R214 C212
30
R1309 R1207 R242
C1305
R1
R208 C211 J1044
C1200
Q203
J1088
C1304 J1095 GND
R218
J1084 R217
8
J1124
1
Q204
P-ON-H1
GND
Q1202
D1300
F
D633 R211
R216
GND
GND
GND
IC200
4
C200
J200
5
R225 R220 R215
J1072
J1049
GND
GND
R221
J1002 R219 J1120
GND R224 VCOM-PWM
VCOM2
C1112
D201
J1034
J1170
GND
C213
PROTECT3
GND
CN200 Q205
J1079
1
BL-ADJ
C215
J1083
11
C214
C218
2 10
J1065
J1020
J1048
BL-SW
GND
GND
J1069
GND
C201
C202
CAUTION !
WAVEFORMS
WF1 ~ WF4 = Waveforms to be observed at

Waveform check points.
(Shown in Schematic Diagram.)
Input: Component Color Bar Signal (480i, 480p, 720p or 1080i)

(with 1kHz Audio Signal)
WF1 JK3701(Y-IN)
VIDEO-Y 0.2V 20s
WF2 JK3701(Pb-IN)
VIDEO-Pb 0.2V 20s
WF3 JK3701(Pr-IN)
VIDEO-Pr 0.2V 20s
WF4 JK3701(AUDIO(L)-IN)
AUDIO 0.1V 0.5ms
11-1 FL11.4WF
COMPONENT
-Y/VIDEO-IN
TUNER UNIT
COMPONENT POWER SUPPLY CBA
-Pb-IN
CL3005 CN3005
COMPONENT CN1100 STV 1
CN3701 CL632 CN632
-Pr-IN 1 BACK XAO 2
1 VCOM-PWM 1
2 LIGHT OE1 3
2 BACKLIGHT-SW 2 HDMI-
3 BACKLIGHT-ADJ 3 CPV 4
CONNECTOR-1
AUDIO(L)-IN POL 5
4 PROTECT3 4
CN1101 TP 6
5 PROTECT1 5
1 BACK GND 7
AUDIO(R)-IN 6 P-ON-H1 6
2 LIGHT LLV5(-) 8
7 P-ON-H2 7
8 RESET 8 LLV5(+) 9 HDMI-
DIGITAL 9 OE2 9 LLV4(-) 10 CONNECTOR-2
AUDIO-OUT CN1102 LLV4(+) 11
10 GND 10
(COAXIAL) 1 BACK LLV3(-) 12
11 AL+5V 11
2 LIGHT LLV3(+) 13
12 GND 12
13 AMP+24V 13 GND 14
14 AMP+24V 14 LLVCLK(-) 15
CN200 CL200
15 GND 15 LLVCLK(+) 16 PC-RGB-IN
1 GND
16 P-ON+24V 16 GND 17
2 LCD+15.8V
17 P-ON+24V 17 LLV2(-) 18
3 LCD+15.8V
18 GND 18 LLN2(+) 19
4 VGH
19 GND 19 LLV1(-) 20
5 GND
LLV1(+) 21
12-1
6 P-ON+3.3V
LLV0(-) 22
7 P-ON+3.3V USB JACK
LLV0(+) 23
8 LCD-6V
GND 24
9 GND
10 VCOM
11 GND
LCD MODULE
CN4052 CL3102 CN3102 ASSEMBLY
1 GND 1
WIRING DIAGRAM
*1 CN600
2 REMOTE 2
3 AL+3.3V 3 AC600
*2 CN601
4 P-ON+5V 4 AC CORD
5 LED1 5 1
6 KEY-IN1 6 2
7 LIGHT 7
IR SENSOR CBA UNIT
*1 LC320EM2 (Serial No. : DS1),

32MF301B/F7 (Serial No. : DS1),
LC320SS2 (Serial No. : DS1)
CN3801 *2 LC320EM2 (Serial No. : DS3,TH1),

SP3801 32MF301B/F7 (Serial No. : DS2,TH1),
SP(L)- 1
CL3801 SPEAKER LC320SS2 (Serial No. : DS2,TH1)
SP(L)+ 2 L-CH
CN4001 CL3101 CN3101

1 GND 1
2 KEY-IN1 2 CN3802
SP3802
SP(R)- 1
CL3802 SPEAKER
SP(R)+ 2 R-CH
FUNCTION CBA UNIT
FL11.4AWI
EXPLODED VIEWS
Cabinet [TYPE A]
A1
B27
CL3005
Function CBA Unit

A15
CL3101 CL200
S6
A4 B66 X7
Digital Main CBA Unit
B72
A8
B66
B27 B18
CL3102
A42
A11
IR Sensor CBA Unit B66 A2

L19
B11 B64
L27
B5 CL3801 L27
LCD1 L27 B67
B66
SP3801
B11
B64 CL3802
B67 B67 L1
L19
SP3802
B67 L25
CL632 L1
L1
S6
L17
B22 L25
B41 A12
Power Supply CBA
L1
S6
L19
L19 B63 B22
See Electrical Parts List L27
for parts with this mark. L27 L15
LC320EM2 (Serial No.:DS1),
32MF301B/F7 (Serial No.:DS1),
LC320SS2 (Serial No.:DS1)
Stand Assembly
AC600 L28
13-1 FL11.4-A_CEX
Cabinet [TYPE B]
A1
CL3005
Function CBA Unit

A15
CL3101 CL200
S6
A4 X7
Digital Main CBA Unit
A8
B18
CL3102
A42
A11
IR Sensor CBA Unit A2

L19
B11 L27
B5 CL3801 L27
LCD1 L27
SP3801
B11
CL3802
L42
L19
SP3802
L25
CL632 L42
L1
S6
L17
B22 L25
B41 A12
Power Supply CBA
L1
S6
L19
L19 B22
See Electrical Parts List L27
for parts with this mark. L27 L15
AC600
Stand Assembly
L28
13-2 FL11.4-B_CEX
Packing
L28
X3
X6 X2 Tape
X4
Stand
Assembly
S3
S7 X1
Packing Tape
S5
S4
Packing Tape Tape
S6
FR FR
ON ON
T T
S1
Some Ref. Numbers are

not in sequence.
13-3 FL11.4_PEX
TYPE A
PARTS LIST [32MF301B/F7 (Serial No.: DS1)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No.
# have special characteristics important to safety. S4 STYROFOAM BOTTOM A17F1UH 1EM027386
Before replacing any of these components, read S5 SET BAG A17F6UH 1EM330877
carefully the product safety notice in this service S6 SERIAL NO. LABEL A01PBUH ----------
manual. Don't degrade the safety of the product S7 STAND BAG A94F0UH 1EM428757
through improper servicing. ACCESSORIES
X1 BAG POLYETHYLENE 235X365XT0.03 0EM408420A
NOTE: Parts that are not assigned part numbers X2# OWNERS MANUAL A17F0UH 1EMN27701
(---------) are not available. X3 REMOTE CONTROL NF805UD NF805UD
X4 DRY BATTERY R03/2S XB0M451T0006
X6 QUICK START GUIDE A17F0UH 1EMN27702
Ref. No. Description Part No. X7 REGISTRATION CARD (MAGNAVOX) 1EMN27759
A17N0UH
STAND ASSEMBLY A17F1UH 1ESA27585
A1 FRONT CABINET A17F0UH 1EM226003
A2 REAR CABINET A17F1UH 1EM027006
A4 FUNCTION KNOB A17F1UH 1EM226223
A8 JACK HOLDER A17F1UH 1EM225384
A11 SENSOR LENS A17N1UH 1EM329957
A12# RATING LABEL A17F0UH ----------
A15 ENERGY STAR LABEL A91F2UH ----------
A42 ENERGY GUIDE LABEL A17F0UH ----------
AC600# AC CORD W/O A GND WIRE UL/CSA/1700/NO/ WAC1720LW005
BLACK
B5 STAND BRACKET A17F1UH 1EM225385
B11 SPEAKER HOLDER A17F1UH 1EM125714
B18 GASKET A8AF0UH 1EM425861
B22 WALL MOUNT BRACKET A84N0UH 1EM323797
B27 CLOTH(10X180XT0.5) L0336JG 0EM408827
B63 CONNECTOR COVER A17F1UH 1EM331137
B64 CLOTH(10X90XT1.0) A7120UH 1EM424258
B66 CLOTH(15X30XT1.0) B7507UH 0EM402452
B67 CUSHION A17F1UH 1EM435678
B72 CLOTH 15X10XT0.5 1EM420293
CL200 FFC WIRE ASSEMBLY 11PIN 11PIN/110MM WX1A17F1-101
CL3101 WIRE ASSEMBLY 2PIN 2PIN/250MM/BLACK WX1A17F1T205
RED
CL3102 WIRE ASSEMBLY 7PIN 7PIN/600MM/BLACK WX1A17F1T206
RED
CL3801 WIRE ASSEMBLY 2PIN 2PIN/150MM/BLACK WX1A17F1L301
RED
CL3802 WIRE ASSEMBLY 2PIN 2PIN/480MM/BLACK WX1A17F1R302
RED
L1 SCREW P-TIGHT 3X10 BIND HEAD+ GBHP3100
L15 DOUBLE SEMS SCREW M4X10 + BLK FPH34100
L19 ASSEMBLED SCREW ( D9 M3X6 ) A71F0UH 1EM424392B
L25 S-TIGHT SCREW M3X6 BIND HEAD+BLACK GBHS3060
L27 SCREW P-TIGHT M4X14 BIND HEAD+BLK GBHP4140
L28 STAND SCREW KIT A17F1UH 1ESA27587
LCD1 LCD MODULE 31.5INCH 31.5INCH UK32MXB
SP3801 SPEAKER MAGNETIC S0412F28A DS08130XQ001
SP3802 SPEAKER MAGNETIC S0412F28A DS08130XQ001
PACKING
S1 CARTON A17F0UH 1EM434844
S3 STYROFOAM TOP A17F1UH 1EM027385
2011/05/12 14-1 A17F0CA.fm

Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No.
# have special characteristics important to safety. C607 CERAMIC CAP. 820pF/2KV CA3D821PAN04
Before replacing any of these components, read C608 CHIP CERAMIC CAP. B K 0.068F/50V CHD1JK30B683
carefully the product safety notice in this service C609 CHIP CERAMIC CAP. B K 1500pF/50V CHD1JK30B152
manual. Don't degrade the safety of the product C610# SAFTY CAP. 1000pF/250V KX CA2E102MR101
through improper servicing. C611# SAFTY CAP. 1000pF/250V KX CA2E102MR101
C612# SAFTY CAP. 1000pF/250V KX CA2E102MR101
NOTES: C613 CERAMIC CAP. 2200pF/1KV CCD3AKA0R222
1. Parts that are not assigned part numbers (---------) C631 ELECTROLYTIC CAP. 1000F/35V M CE1GMZADL102
are not available. C632 ELECTROLYTIC CAP. 1000F/35V M CE1GMZADL102
C634 CHIP CERAMIC CAP.(1608) F Z 0.1F/50V CHD1JZ30F104
2. Tolerance of Capacitors and Resistors are noted C635 CHIP CERAMIC CAP.(1608) F Z 0.1F/50V CHD1JZ30F104
with the following symbols. C636 CHIP CERAMIC CAP.(1608) F Z 0.1F/50V CHD1JZ30F104
C637 ELECTROLYTIC CAP. 470F/25V M CE1EMASDL471
C.....0.25% D.....0.5% F.....1% C638 ELECTROLYTIC CAP. 100F/25V M CE1EMASDL101
G.....2% J......5% K.....10% C639 ELECTROLYTIC CAP. 100F/10V M CE1AMASDL101

C641 CERAMIC CAP. 2200pF/1KV CCD3AKA0R222
M.....20% N.....30% Z.....+80/-20% C644 ELECTROLYTIC CAP. 1F/50V M CE1JMASDL1R0
C645 CHIP CERAMIC CAP. B K 2200pF/50V CHD1JK30B222
DIGITAL ASSEMBLY C646 ELECTROLYTIC CAP. 100F/10V M CE1AMASDL101

C647 ELECTROLYTIC CAP. 100F/50V M CE1JMASDL101
Ref. No. Description Part No. C648 ELECTROLYTIC CAP. 2200F/35V M CE1GMZNDL222
DIGITAL ASSEMBLY A17F0MMA-004 C649 ELECTROLYTIC CAP. 2200F/35V M CE1GMZNDL222
Consists of the following
C1100 CHIP CERAMIC CAP. F Z 2.2F/50V CHF1JZ30F225
DIGITAL MAIN CBA UNIT A17F0MMA-004-DM
FUNCTION CBA UNIT A17F0MMA-004-FN
IR SENSOR CBA UNIT A17F0MMA-004-IR
C1104 CAP CERAMIC HV 10pF/6.3KV/SL/J CCC1000MR007
POWER SUPPLY CBA C1105 CHIP CERAMIC CAP. CH J 330pF/50V CHD1JJ3CH331
Ref. No. Description Part No.
C1107 CHIP CERAMIC CAP. CH J 330pF/50V CHD1JJ3CH331
POWER SUPPLY CBA A17F1MPW-001 C1108 CAP CERAMIC HV 10pF/6.3KV/SL/J CCC1000MR007
Consists of the following:
CAPACITORS
C203 ELECTROLYTIC CAP. 2.2F/50V M CE1JMASDL2R2
C205 CHIP CERAMIC CAP.(1608) B K 0.1F/50V CHD1JK30B104
C211 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C213 CHIP CERAMIC CAP.(1608) B K 1F/25V CHD1EK30B105
C223 CHIP CERAMIC CAP.(1608) B K 1F/25V CHD1EK30B105
C1202 CHIP CERAMIC CAP.(1608) B K 6800pF/50V CHD1JK30B682
C230 ELECTROLYTIC CAP. 100F/10V M CE1AMASDL101
C1208 CAP CHIP 3216 B K 0.47F/50V CA1J474TE142
C600# CAP METALIZED FILM 0.47F/300V K 3.5MM CT2F474DC004
C1209 CAP CHIP 3216 B K 0.47F/50V CA1J474TE142
C601# CAP METALIZED FILM 0.47F/300V K 3.5MM CT2F474DC004
C1210 CHIP CERAMIC CAP.(1608) B K 0.47F/16V CHD1CK30B474
C603 CAP ELECTROLYTIC 270F/200V CEA271DYG005
C1212 CHIP CERAMIC CAP.(1608) B K 0.47F/16V CHD1CK30B474
C604 CAP ELECTROLYTIC 270F/200V CEA271DYG005
C606 CHIP CERAMIC CAP. B K 1200pF/50V CHD1JK30B122
2011/05/12 14-2 A17F0EL.fm

Ref. No. Description Part No. Ref. No. Description Part No.
C1301 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102 D643 DIODE SK16-T/R ND1Z0000SK16
C1302 ELECTROLYTIC CAP. 10F/50V M CE1JMASDL100 D644 DIODE SCHOTTKY SB3150BH NDWZ00SB3150
C1303 CHIP CERAMIC CAP.(1608) B K 0.1F/50V CHD1JK30B104 D645 DIODE ZENER 1ZB22BB NDWZ0001ZB22
C1304 ELECTROLYTIC CAP. 220F/35V M CE1GMASDL221 D646 DIODE SCHOTTKY SB3150BH NDWZ00SB3150
C1305 CHIP CERAMIC CAP.(1608) B K 0.1F/50V CHD1JK30B104 D648 DIODE ZENER 1ZB30BB NDWZ0001ZB30
C1311 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102 D649 DIODE SK16-T/R ND1Z0000SK16
C1500 CHIP CERAMIC CAP.(1608) B K 0.01F/50V CHD1JK30B103 D650 DIODE ZENER 5V6BSB-T26 NDTB5R6BST26
C1501 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102 D651 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
C1700 ELECTROLYTIC CAP. 2200F/35V M CE1GMZNDL222 D654 DIODE ZENER 5V6BSB-T26 NDTB5R6BST26
C1702 CAP CHIP 3216 B K 1F/50V CA1J105TE142 D655 DIODE ZENER 3V3BSB-T26 NDTB3R3BST26
C1703 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102 D656 DIODE ZENER 5V6BSB-T26 NDTB5R6BST26
C1705 CHIP CERAMIC CAP.(1608) B K 0.022F/50V CHD1JK30B223 D658 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
C1706 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102 D660 DIODE FAST RECOVERY RS1GJTB ND1Z0RS1GJTB
C1708 CHIP CERAMIC CAP.(1608) B K 0.022F/50V CHD1JK30B223 D1200 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
C1709 ELECTROLYTIC CAP. 2200F/35V M CE1GMZNDL222 D1201 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
C1710 CAP CHIP 3216 B K 1F/50V CA1J105TE142 D1202 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
CONNECTORS D1203 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
CN200 FFC CONNECTOR IMSA-9615S-11A-PP-A JC96J11ER007 D1300 DIODE ZENER 5V6BSB-T26 NDTB5R6BST26
CN600# VH CONNECTOR PRINT OSU B2P3S- J3VH030JG002 D1301 DIODE ZENER 5V6BSB-T26 NDTB5R6BST26
VH(LF)(SN) D1500 SWITCHING DIODE DAN202U T106 QD1Z0DAN202U
CN632 FMN CONNECTOR TOP 19P IMSA-9615S-19A- JC96J19ER007 D1501 SWITCHING DIODE DAN202U T106 QD1Z0DAN202U
PP-A
D1502 SWITCHING DIODE DAN202U T106 QD1Z0DAN202U
CN1100# CONNECTOR/JACK 1747386-1 JB17J02AP002
DIODES
D200 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D205 DIODE ZENER 24BSC-T26 NDTC024BST26
D1701 DIODE ZENER 15BSB-T26 NDTB015BST26
D210 DIODE ZENER 6V2BSB-T26 NDTB6R2BST26
D221 IC SHUNT REGULATOR KIA431-AT/P NSZBA0TJY036
ICS
IC200 IC TL3472CDR NSZBA0TTY115
D600# DIODE GENERAL PURPOSE 1N5406-BU NDLZ1N5406BU
IC202 IC(REGULATOR) PQ200WNA1ZPH QSZBA0TSH072
IC601# IC PHOTOCOUPLER TLP781F(D4-FUNBLL F) QPEL781FBLLF
IC1200 IC INVERTER CONTROL BD9244AFV/SSOP/ QSCA0T0RM222
D603# DIODE GENERAL PURPOSE 1N5406-BU NDLZ1N5406BU 24PIN
D604# DIODE ZENER 27BSB-T26 NDTB027BST26
COILS
L600# COIL LINE FILTER ST0807ET28-009 10MH LLEG0Z0Y2029
D607# SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
L601# COIL LINE FILTER ST0807ET28-009 10MH LLEG0Z0Y2029
TRANSISTORS
D610# DIODE ZENER 1ZB36BB NDWZ0001ZB36
Q200 PNP TRANSISTOR SMD 2SA1576UBTLQ QQ1Q2SA1576U
D611 DIODE ZENER 1ZB220-YBB NDWZ01ZB220Y
Q201 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S
D613 DIODE FAST RECOVERY FR155-B/P NDWZ0FR155BP
D634 DIODE SCHOTTKY SB3150BH NDWZ00SB3150
D635 DIODE ZENER 1ZB7.5BB NDWZ001ZB7R5
D637 DIODE SCHOTTKY SB3150BH NDWZ00SB3150
D640 DIODE SCHOTTKY SMD SK2B-TR ND1Z00SK2BTR
D642 DIODE SK16-T/R ND1Z0000SK16
Q221 TRANSISTOR 2SC2120-Y(TE2 F T) QQSY2SC2120F
2011/05/12 14-3 A17F0EL.fm

Q222 TRANSISTOR 2SA950-O (TE2 F T) QQS002SA950F R251 RES CHIP 1608 1/10W J 22k RRXA223HH013
Q600# FET MOS TK10A50D QFWZTK10A50D R252 RES CHIP 1608 1/10W J 39k RRXA393HH013
Q601# TRANSISTOR 2SC2120-Y(TE2 F T) QQSY2SC2120F R253 RES CHIP 1608 1/10W J 22k RRXA223HH013
Q631 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S R254 RES CHIP 1608 1/10W J 22k RRXA223HH013
Q632 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S R255 RES CARBON FILM T 1/4W J 390 RCX4391T1001
Q633 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S R256 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
Q634 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S R257 RES CARBON FILM T 1/4W J 8.2k RCX4822T1001
Q635 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S R258 RES CARBON FILM T 1/4W J 2.7k RCX4272T1001
Q636 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P R260 RES CHIP 1608 1/10W J 47k RRXA473HH013
Q1300 PNP TRANSISTOR SMD 2SA1576UBTLQ QQ1Q2SA1576U R263 RES CARBON FILM T 1/4W J 470 RCX4471T1001
Q1303 PNP TRANSISTOR SMD 2SA1576UBTLQ QQ1Q2SA1576U R265 RES CARBON FILM T 1/4W J 8.2k RCX4822T1001
Q1700# FET MOS SMD TK50P04M1(T6RSS-Q) QF1ZK50P04M1 R266 RES CARBON FILM T 1/4W J 47k RCX4473T1001
Q1701# FET MOS SMD TK50P04M1(T6RSS-Q) QF1ZK50P04M1 R267 RES CHIP 1608 1/10W J 47k RRXA473HH013
Q1702# FET MOS SMD TK50P04M1(T6RSS-Q) QF1ZK50P04M1 R268 RES CARBON FILM T 1/4W J 47k RCX4473T1001
Q1703# FET MOS SMD TK50P04M1(T6RSS-Q) QF1ZK50P04M1 R269 RES CHIP 1608 1/10W J 12k RRXA123HH013
RESISTORS R270 RES CHIP 1608 1/10W J 1.5k RRXA152HH013
R200 RES CHIP 1608 1/10W J 100k RRXA104HH013 R600 RES CHIP 3216 1/4W J 220k RRX4224HH034
R201 RES CHIP 1608 1/10W J 1.0k RRXA102HH013 R601# RES. CARBON FILM J 1/2W J 1.2M RCX2125T1003
R203 RES CARBON FILM T 1/4W J 560 RCX4561T1001 R602# CEMENT RESISTOR 5W J 2.2 H 10MM RW052R2PAK10
R205 RES CHIP 1608 1/10W J 1.0k RRXA102HH013 R603 RES CHIP 3216 1/4W J 220k RRX4224HH034
R206 RES CHIP 1608 1/10W J 100k RRXA104HH013 R604 RES CHIP 3216 1/4W J 220k RRX4224HH034
R207 RES CHIP 1608 1/10W J 1.0 RRXA1R0HH013 R605 RES CARBON FILM T 1/4W J 220 RCX4221T1001
R208 RES CHIP 1608 1/10W 0 RRXA000HH014 R606 RES CARBON FILM T 1/4W J 180 RCX4181T1001
R209 RES CARBON FILM T 1/4W J 10 RCX4100T1001 R607 RES CARBON FILM T 1/4W J 1.2k RCX4122T1001
R210 RES CHIP 1608 1/10W 0 RRXA000HH014 R608# METAL OXIDE FILM RES. 2W J 0.18 RN02R18ZU001
R211 RES CARBON FILM T 1/4W J 10 RCX4100T1001 R609 RES CARBON FILM T 1/4W J 3.9k RCX4392T1001
R212 RES CHIP 1608 1/10W J 100k RRXA104HH013 R610 RES CARBON FILM T 1/4W J 270 RCX4271T1001
R213 RES CHIP 1608 1/10W 0 RRXA000HH014 R611# CEMENT RESISTOR 5W J 2.2 H 10MM RW052R2PAK10
R215 RES CHIP 1608 1/10W J 12k RRXA123HH013 R612 METAL OXIDE FILM RES. 1W J 68k RN01683ZU001
R216 RES CHIP 1608 1/10W J 1.2k RRXA122HH013 R613 METAL OXIDE FILM RES. 1W J 68k RN01683ZU001
R217 RES CHIP 1608 1/10W J 10k RRXA103HH013 R631 RES CHIP 1608 1/10W J 15k RRXA153HH013
R219 RES CHIP 1608 1/10W J 1.0k RRXA102HH013 R633 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
R222 RES CHIP 1608 1/10W J 10k RRXA103HH013 R634 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
R226 RES CHIP 1608 1/10W F 330 RTW3300HH008 R637 RES CHIP 1608 1/10W J 10k RRXA103HH013
R228 RES CHIP 1608 1/10W J 4.7k RRXA472HH013 R641 RES CHIP 1608 1/10W J 22k RRXA223HH013
R229 RES CHIP 1608 1/10W J 22k RRXA223HH013 R642 RES CHIP 1608 1/10W F 43.0k RTW4302HH008
R233 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 R647 RES CHIP 1608 1/10W F 27.0k RTW2702HH008
R234 RES. CARBON FILM J 1/2W J 2.2 RCX22R2T1003 R649 RES CARBON FILM T 1/4W J 3.9k RCX4392T1001
R235 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 R650 RES CHIP 1608 1/10W J 1.0 RRXA1R0HH013
R236 RES CHIP 1608 1/10W F 11.0k RTW1102HH008 R651 RES CHIP 1608 1/10W F 820 RTW8200HH008
R237 RES CHIP 1608 1/10W F 750 RTW7500HH008 R652 RES CHIP 1608 1/10W F 18.0k RTW1802HH008
R238 RES CHIP 1608 1/10W F 2.20k RTW2201HH008 R654 RES CHIP 1608 1/10W J 10k RRXA103HH013
R239 METAL OXIDE FILM RES. 1W J 8.2 RN018R2ZU001 R655 RES CHIP 1608 1/10W J 47k RRXA473HH013
R240 RES CARBON FILM T 1/4W J 3.9k RCX4392T1001 R656 RES CARBON FILM T 1/4W J 220 RCX4221T1001
R241 RES CHIP 1608 1/10W J 6.8k RRXA682HH013 R657 RES CARBON FILM T 1/4W J 15 RCX4150T1001
R242 RES CHIP 1608 1/10W J 2.7k RRXA272HH013 R658 RES CARBON FILM T 1/4W J 220 RCX4221T1001
R243 RES CHIP 1608 1/10W F 240 RTW2400HH008 R659 RES CARBON FILM T 1/4W J 220 RCX4221T1001
R244 RES CHIP 1608 1/10W F 2.20k RTW2201HH008 R660 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
R246 RES CARBON FILM T 1/4W J 3.9k RCX4392T1001 R662 RES CARBON FILM T 1/4W J 220 RCX4221T1001
R249 RES CHIP 1608 1/10W J 6.8k RRXA682HH013 R1100 RES CHIP 1608 1/10W F 39.0k RTW3902HH008
R1101 RES CHIP 1608 1/10W 0 RRXA000HH014
2011/05/12 14-4 A17F0EL.fm

R1103 RES CARBON FILM T 1/4W G 470 RCX4471T1002 R1500 RES CHIP 1608 1/10W F 1.00M RTW1004HH008
R1104 RES CHIP 1608 1/10W F 100 RTW1000HH008 R1501 RES CHIP 1608 1/10W F 100k RTW1003HH008
R1105 RES CHIP 1608 1/10W F 13.0 RTW13R0HH008 R1502 RES CHIP 1608 1/10W F 100k RTW1003HH008
R1106 RES CARBON FILM T 1/4W G 470 RCX4471T1002 R1503 RES CHIP 1608 1/10W F 100k RTW1003HH008
R1107 RES CHIP 1608 1/10W F 100 RTW1000HH008 R1504 RES CHIP 1608 1/10W F 100k RTW1003HH008
R1108 RES CHIP 1608 1/10W F 13.0 RTW13R0HH008 R1505 RES CHIP 1608 1/10W F 100k RTW1003HH008
R1109 RES CHIP 1608 1/10W F 39.0k RTW3902HH008 R1506 RES CHIP 1608 1/10W F 100k RTW1003HH008
R1110 RES CHIP 1608 1/10W 0 RRXA000HH014 R1507 RES CHIP 1608 1/10W F 100k RTW1003HH008
R1113 RES CHIP 1608 1/10W 0 RRXA000HH014 R1510 RES CHIP 1608 1/10W F 100k RTW1003HH008
R1115 RES CARBON FILM T 1/4W G 470 RCX4471T1002 R1512 RES CHIP 1608 1/10W F 100k RTW1003HH008
R1116 RES CHIP 1608 1/10W F 100 RTW1000HH008 R1513 RES CHIP 1608 1/10W F 1.00M RTW1004HH008
R1117 RES CHIP 1608 1/10W F 13.0 RTW13R0HH008 R1514 RES CHIP 1608 1/10W F 39.0k RTW3902HH008
R1118 RES CARBON FILM T 1/4W G 470 RCX4471T1002 R1515 RES CHIP 1608 1/10W F 27.0k RTW2702HH008
R1119 RES CHIP 1608 1/10W F 100 RTW1000HH008 R1516 RES CHIP 1608 1/10W F 6.80k RTW6801HH008
R1120 RES CHIP 1608 1/10W F 13.0 RTW13R0HH008 R1700 RES CHIP 1608 1/10W J 100 RRXA101HH013
R1122 RES CHIP 1608 1/10W 0 RRXA000HH014 R1702 RES CHIP 1608 1/10W J 100 RRXA101HH013
R1124 RES CHIP 1608 1/10W F 39.0k RTW3902HH008 R1704 METAL OXIDE FILM RES. 1W J 4.7 RN014R7ZU001
R1125 RES CHIP 1608 1/10W 0 RRXA000HH014 R1705 RES CHIP 1608 1/10W J 100 RRXA101HH013
R1127 RES CARBON FILM T 1/4W G 470 RCX4471T1002 R1707 RES CHIP 1608 1/10W J 100 RRXA101HH013
R1128 RES CHIP 1608 1/10W F 100 RTW1000HH008 R1708 RES CHIP 1608 1/10W J 10k RRXA103HH013
R1129 RES CHIP 1608 1/10W F 13.0 RTW13R0HH008 R1709 METAL OXIDE FILM RES. 1W J 4.7 RN014R7ZU001
R1130 RES CARBON FILM T 1/4W G 470 RCX4471T1002 MISCELLANEOUS
R1131 RES CHIP 1608 1/10W F 100 RTW1000HH008 B41 HEAT SINK PNB ASSEMBLY A94F0UH 1EM428123
R1132 RES CHIP 1608 1/10W F 13.0 RTW13R0HH008 BC601 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
R1133 RES CHIP 1608 1/10W F 39.0k RTW3902HH008 BC602 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
R1134 RES CHIP 1608 1/10W 0 RRXA000HH014 F601# FUSE STC4A125V U/CT PAGE20CW3402
R1135 RES CHIP 1608 1/10W F 2.20k RTW2201HH008 FH601 FUSE HOLDER MSF-015 LF (B110) XH01Z00LY002
R1200 RES CHIP 1608 1/10W J 68k RRXA683HH013 FH602 FUSE HOLDER MSF-015 LF (B110) XH01Z00LY002
R1201 RES CHIP 1608 1/10W J 68k RRXA683HH013 JS200 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
R1202 RES CHIP 1608 1/10W F 130k RTW1303HH008 JS660 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
R1203 RES CHIP 1608 1/10W F 8.20k RTW8201HH008 JS1200 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
R1204 RES CHIP 1608 1/10W F 75.0k RTW7502HH008 L17 SCREW B-TIGHT D3X8 BIND HEAD+ GBJB3080
R1205 RES CHIP 1608 1/10W F 560k RTW5603HH008 SA601# SURGE ABSORBER 470V+-10PER NVQZ10D471KB
R1206 RES CHIP 1608 1/10W J 10k RRXA103HH013 T600# TRANS POWER 11714 LTT3PC0KT069
R1207 RES CHIP 1608 1/10W J 33k RRXA333HH013 When you replace one of the below Trans Inverters on this CBA, please
R1208 RES CHIP 1608 1/10W J 22k RRXA223HH013 replace with the one that has same parts number.
Do not mix different parts numbers Trans Inverter.
R1209 RES CHIP 1608 1/10W J 4.7k RRXA472HH013
T1100# TRANS INV HVT-325 LTZ3PZ0XB018
R1212 RES CHIP 1608 1/10W J 10k RRXA103HH013
or
T1100# TRANS INV TZ.7617A.101 LTZ3PZDAR014
R1216 RES CHIP 1608 1/10W J 100 RRXA101HH013
R1221 RES CHIP 1608 1/10W J 1.0 RRXA1R0HH013
R1300 RES CHIP 1608 1/10W F 10.0k RTW1002HH008
R1305 METAL OXIDE RES. 2W J 510 RN02511ZU001
2011/05/12 14-5 A17F0EL.fm

TYPE A
PARTS LIST [LC320EM2 (Serial No.: DS1)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTE: Parts that are not assigned part numbers
(---------) are not available.
Different parts from the original model

32MF301B/F7 (Serial No. : DS1)
X2# OWNERS MANUAL A17F1UH 1EMN27479
X3 REMOTE CONTROL NH001UD NH001UD
X7 REGISTRATION CARD (EMERSON) A17N1UH 1EMN27763
2011/05/12 14-6 A17F1CA.fm

Electrical Parts
NOTES:
1. Parts that are not assigned part numbers (---------)
are not available.
2. Tolerance of Capacitors and Resistors are noted
with the following symbols.
C.....0.25% D.....0.5% F.....1%

G.....2% J......5% K.....10%
M.....20% N.....30% Z.....+80/-20%

DIGITAL ASSEMBLY A17F1MMA-006
POWER SUPPLY CBA ----------

You cannot mix components under Type 1 with the ones under Type 2.
Type 1: (78R000ZF is engraved on Type 1 IC REGULATOR.)
IC202 IC REGULATOR KIA78R000ZF-RTF/P NSCA0T0JY016
R244 RES CHIP 1608 1/10W F 1k RTW1001HH008
Make sure to use this IC202 with R226 (1.4k )

and R244 (1k ).
or
Type 2: (200WNA1 is engraved on Type 2 IC REGULATOR.)
IC202 IC(REGULATOR) PQ200WNA1ZPH QSZBA0TSH072
R226 RES CHIP 1608 1/10W F 330 RTW3300HH008
Make sure to use this IC202 with R226 (330 )

and R244 (2.2k ).
2011/05/12 14-7 A17F1EL.fm

TYPE A
PARTS LIST [LC320SS2 (Serial No.: DS1)]
Mechanical Parts
NOTE: Parts that are not assigned part numbers
(---------) are not available.

X2# OWNERS MANUAL A17F2UH 1EMN27703
X7 REGISTRATION CARD (SYLVANIA) A017DUH 1EMN27080
2011/05/12 14-8 A17F2CA.fm

Electrical Parts
NOTES:
1. Parts that are not assigned part numbers (---------)
are not available.
2. Tolerance of Capacitors and Resistors are noted
with the following symbols.
C.....0.25% D.....0.5% F.....1%

G.....2% J......5% K.....10%
M.....20% N.....30% Z.....+80/-20%

2011/05/12 14-9 A17F2EL.fm

32MF301B/F7(A17F0UH)(Serial No.: DS2)
20110421
32MF301B/F7(A17F0UH)(Serial No.: DS2)
Different parts from the original model 32MF301B/F7(DS1)

Ref. No. Description Parts No.
MECHANICAL PARTS
A1 FRONT CABINET A17F0UH 1EM226003A
A2 REAR CABINET A17F1UH 1EM027006A
AC600! AC CORD W/O A GND WIRE UL/CSA/1730/NO/BLACK WAC1720LW006
B63 Not used
CL3101 WIRE ASSEMBLY 2PIN 2PIN/250MM/BLACK RED WX1A17F1T207
ELECTRICAL PARTS
POWER SUPPLY CBA A17F1MPWA002

CN600! Not used
CN601! CONNECTOR B2P3-VH(LF)(SN) J3VH020JG001
1 / 1 page
LC320EM2(A17F1UH)(Serial No.: DS3)
20110414
LC320EM2(A17F1UH)(Serial No.: DS3)

MECHANICAL PARTS
A12! RATING LABEL A17F1UH ----------
B63 Not used
X2! OWNERS MANUAL A17F1UH 1EMN27479
X7 REGISTRATION CARD (EMERSON) A17N1UH 1EMN27763
ELECTRICAL PARTS


CN600! Not used
1 / 1 page
LC320SS2(A17F2UH)(Serial No.: DS2)
20110414
LC320SS2(A17F2UH)(Serial No.: DS2)

MECHANICAL PARTS
A12! RATING LABEL A17F2UH ----------
B63 Not used
X2! OWNERS MANUAL A17F2UH 1EMN27703
X7 REGISTRATION CARD (SYLVANIA) A017DUH 1EMN27080
ELECTRICAL PARTS


CN600! Not used
1 / 1 page
LC320EM2(A17F8UT)(Serial No.: TH1)
20110421
LC320EM2(A17F8UT)(Serial No.: TH1)

MECHANICAL PARTS
STAND ASSEMBLY A17F8UT 1ESA28630
A12! RATING LABEL A17F8UT ----------
B11 SPEAKER HOLDER A17F1UH 1EM126473
B27 Not used
B63 Not used
B64 Not used
B66 Not used
B67 Not used
B72 Not used
L28 STAND SCREW KIT A17F8UT 1ESA28631
L42 SHOULDER SCREW A01Q0UF 1EM328277
SP3801 SPEAKER MAGNETIC S0412F28E DS08130XQ004
SP3802 SPEAKER MAGNETIC S0412F28E DS08130XQ004
S1 CARTON A17F8UT 1EM331060
S7 STAND BAG A01FKUT 1EM432498
X2! OWNERS MANUAL A17F8UT 1EMN28127
X6 QUICK START GUIDE A17F8UT 1EMN28128
X7 REGISTRATION CARD (EMERSON) A17N8UT 1EMN28129
ELECTRICAL PARTS

POWER SUPPLY CBA A17F8MPW-001

C600 CAP METALLIZED FILM 0.47UF/250V/K/MPX CTA474EUR001
C601 CAP METALLIZED FILM 0.47UF/250V/K/MPX CTA474EUR001
C602 CAP ELECTROLYTIC 390UF/200V CEB391DYG006
C603 Not used
C604 Not used
CN600! Not used
B41 HEAT SINK PNB ASSEMBLY A01FNUT 1EM432598
1 / 1 page
REVISION HISTORY
Chassis FL11.4
2011-02-08 LC320EM2 (Serial No. : DS1) added
2011-03-16 32MF301B/F7 (Serial No. : DS1) added
2011-03-16 LC320SS2 (Serial No. : DS1) added
TBD 32MF301B/F7 (Serial No. : TH1) added
TBD LC320SS2 (Serial No. : TH1) added
TBD 32MF301B/F7 (Serial No. : DS2) added
TBD LC320EM2 (Serial No. : DS3) added
TBD LC320SS2 (Serial No. : DS2) added
TBD LC320EM2 (Serial No. : TH1) added
15-1 FL11.4REV
COMPARISON LIST OF MODEL NAME
Chassis FL11.4
32MF301B/F7 (DS1) A17F0UH
(DS2) A17F0UH
(TH1) A17FAUT
LC320EM2 (DS1) A17F1UH

(DS3) A17F1UH
(TH1) A17F8UT
LC320SS2 (DS1) A17F2UH

(DS2) A17F2UH
(TH1) A17FBUT
FL11.4COM

FL11 4 Funi PDF

Uploaded by

Copyright:

Available Formats

FL11 4 Funi PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

FL11 4 Funi PDF

Uploaded by

Copyright:

Available Formats

32 LCD TV

This service manual contains information of different types of models.

2011 Funai Electric Co., Ltd.

The LCD panel is manufactured to provide many years of useful life.

< TUNER / ATSC >

< LCD PANEL >

< VIDEO >

< AUDIO >

Note: This table is unofficial and for reference only. Be

2. Leakage Current Test

Table 2: Leakage current ratings for selected areas

2. For other ICs, pin 1 and every fifth pin are

3. The 1st pin of every male connector is indicated as Fig. S-1-1

3. Bottom of the flat pack-IC is fixed with glue to the

Fine Tip Fig. S-1-8

1. Ground for Human Body

2. Ground for Workbench

<Correct> Grounding Band

[2] Rear Cabinet (S-2)

[1] Stand Assembly

Function [3] Digital Main

Power Supply CBA

IR Sensor CBA Unit To AC Cord

[2] Rear Cabinet (S-2)

[1] Stand Assembly

Function [3] Digital Main

[4] Power Supply CBA (S-6)

Power Supply CBA

Press "POWER" key to exit.

3. To cancel or to exit from the Purity Check Mode,

Software upgrade in progress. Please wait.

The software upgrade is completed.

Remove the USB storage device from the USB

Is normal state restored when once unplugged No

Check each rectifying circuit of the secondary

FLOW CHART NO.2

After servicing, replace the fuse.

FLOW CHART NO.3

Check IC601, D607, D609 and their periphery circuit,

FLOW CHART NO.4

FLOW CHART NO.6

FLOW CHART NO.7

FLOW CHART NO.8

Check if there is any leak or short-circuit on

FLOW CHART NO.10

FLOW CHART NO.11

Replace Digital Main CBA Unit.

FLOW CHART NO.2

Operation is possible from the unit.

Replace Digital Main CBA Unit.

FLOW CHART NO.3

CL3005, Digital Main CBA Unit or LCD Module

SP3801, SP3802, CL3801 or CL3802 may be

CN3102 CN4052 D4051

IR SENSOR CBA UNIT

P-ON-H2 B16 Q3006

PROTECT3 B13 4 PROTECT3 4

TU3401 (TUNER UNIT)

SCL R12 4 SCL POWER SUPPLY CBA