Step 2 continued (PPPoA or PPPoE) Step 2 continued (DHCP-RFC 1483) Step 2 continued (Manual-RFC 1483) Step 3: Next steps

Step 2 continued (Manual-RFC 1483) Step 3: Next steps CallSwitch IP

A) Troubleshooting
Fast Installation Guide
H) Select the option given by your broadband supplier and click on the Next If your broadband type is DHCP and you have selected this option. If your broadband type is Manual and you have selected this option.
key. Your CallSwitch IP has an activity status panel at the front of your system. The status
These steps should be followed. These steps should be followed.
of the lights (LEDS) will help you see if all your connections are properly installed.
Enter all the details provided by your
broadband supplier in the boxes provided. Page

RED Solid Green Flashing Green OFF

Click on “Next”. Power
Select the RFC 1483 Mode that your Power LED
Power or Power ON - Power OFF
broadband has provided you with. device malfunction
Ethernet

Click on “Next”. DSL

Powered device
connected to the No cable connection
Ethernet LED - -
CallSwitch IP LAN or
Internet no powered device
By default your CallSwitch IP is programmed with the PPPoA option. As an
Enter your broadband service Username
example you can see below how to continue programming this option. and Password. Wireless DSL line connected DSL attempting
- and synchronised. to synchronise -
Note: PPPoE follows the same steps for programming as PPPoA. DSL LED
(Occasional flicker)
Note: In some cases a Password may
Enter your broadband service Username not be required. In this case just enter Username/password IP connected. IP connected DSL line
and Password. the Username. Internet LED incorrect. (No traffic detected) (Traffic detected) not connected
VPI/VCI incorrect

Note: In some cases a Password may Enter the VPI and VCI settings Click on “Next”.
not be required. In this case just enter as supplied by your broadband
- Wireless LAN Wireless LAN Wireless LAN
the Username. supplier. Wireless LED activity present
enabled disabled

Click on “Next”. Click on “Next”.

Enter the VPI and VCI settings
as supplied by your broadband
supplier.
Note: If the Power led flashes red, it means CallSwitch IP is in DECT registration
Click on “Next”. mode.
Enter the VPI and VCI settings
as supplied by your broadband C) Quick Reference Guide
supplier. Confirm the configuration by
Use this to get the most from the telephone features of your CallSwitch IP.
selecting “Confirm Changes”.
Click on “Next”.
For example, you can use your CallSwitch IP to take messages when you
are not available to answer your phone. (Voicemail).

D) Owner’s Manual
This completes the ADSL programming (DHCP type).
Confirm the configuration by
selecting “Confirm Changes”. The Owner’s Manual is contained in the Documentation CD. Use it to CallSwitch IP
learn how to access the advanced capabilities of your CallSwitch IP.
For example, you can connect your PC to the CallSwitch IP LAN without
needing to have them connected via a cable. (Wireless LAN). You can Phones, Broadband and Wireless
Confirm the configuration by This completes the ADSL programming (PPPoA or PPPoE type).
also use your CallSwitch IP to make calls over the Internet. (VoIP).
all in one box
selecting “Confirm Changes”. NOTE: More information can be obtained of how to program your
ADSL Modem from the Owner’s Manual. It may take several minutes for the DSL to synchronise. Fast Installation Guide
Your CallSwitch IP is ready to browse the Internet once the DSL LED

This completes the ADSL programming (PPPoA or PPPoE type).

6 7 has gone solid green with an occasional flicker, and the Internet LED
is solid or flashing green.
8 PN LR2770.01010-1
Welcome Step 1: Connect your telephones Step 1 continued Step 2: Connect to the Internet Step 2 continued

D) Plug the other end of the Line Cable (grey) into the phone connector of A) Connect the LAN Cable (yellow) from the LAN port of your PC to any of the This will open the programming interface Welcome screen.
Welcome to your new CallSwitch IP. Your pack should contain the items pictured the splitter supplied with your DSL service. Plug the splitter into the BT wall ETHERNET sockets of your CallSwitch IP (yellow).
It allows you to programme the PBX and Router configuration.
below. These instructions show you how to connect telephones and the telephone telephone outlet.
line to the system so you can make and receive calls. They also show how to Plug one end of the DSL cable (violet) into the ADSL Modem connector of the
connect to the Internet over your DSL Line so you can browse the web, use email, splitter supplied with your DSL sevice. E) Click on the Router Configuration option to program the ADSL Modem as required
or even make telephone calls over the Internet.
by your broadband supplier. Once you finish your configuration, you will be able to
browse the Internet.
A
r
Powe

D
net
Ether
DSL

net
Inter

less
Wire H
Hold Program Message Directory

1 Featurephone A) If your CallSwitch IP came with a Featurephone please plug this into
C
(Optional) the EXTN 20 socket on the back of the CallSwitch IP. Otherwise plug a standard E) Connect the other end of the DSL cable (violet) to the DSL connector of your A
Line 1 Line 2 Line 3 Line 4
No.

Ext.

phone into the EXTN 20 socket. CallSwitch IP.

F) Connect the Power Supply Unit to the CallSwitch IP and the mains power outlet.
It is possible to connect up to three other phones to the CallSwitch IP. These
should be plugged into any remaining extension sockets. (EXTN 21-23).
1 CallSwitch IP 1 Cable Cover

DSL
Click
B) Open a web browser, such as Internet Explorer or similar, on your PC.
E E
B F
1 Documentation Pack:
1 Line Cable (grey)
(1 CD incl. Owner’s Manual) A C) Open the CallSwitch IP Management Application by entering the following
address into your web browser: http://192.168.1.1
(1 Phone Quick Reference Guide)
(1 Fast Installation Guide) F) Wait approximately one minute for the system to initialise. You can now make
B) Plug the Line Cable (grey) into the Line 1 socket on the back of the CallSwitch IP. telephone calls. C F) Click on the ADSL Modem option to view and select your broadband type of access
Note: This information is given by your broadband supplier.
*****Do not proceed beyond this stage until calls can be made and received*****
1 DSL Cable (violet) 1 AC Adapter
G) Set up and register the DECT Handset(s) that are supplied with your CallSwitch IP D) Enter the Username (admin) and the Password (admin) and press OK.
by following the instructions supplied with the handset.

Note:
1 LAN Cable (yellow)
C C) Fit the Cable Cover over the phone
connections.
NOTE: After powering on the DECT Handsets for the first time, the batteries
should be charged for 14 hours to get maximum battery performance. (If this screen does not appear, check
DECT Handset your PC settings for automatically
& Charger NOTE: If you wish to have any of your phones located away from the CallSwitch IP
obtaining an “IP address” or ensure Click
(includes separate please see the Owner’s Manual for cabling instructions.
that the PROXY server setting is F
instruction sheet) 1 ADSL Splitter
NOTE: Voice features can be programmed from the V8 featurephone turned OFF. Refer to Appendix E in
1 2 on extension 20. For instructions refer to Apendix C in the Owner’s Manual
on the Documentation CD.
3 D Owner’s Manual on the Documentation
CD).
4 5