PDS-POLYKEN-1027-V1-AUG17 - AARPS-0972 Prymer

PRODUCT DATA SHEET
POLYKEN 1027
Product properties
Product Information Property Typical values
Product description: Polyken liquid adhesive systems are Base Rubber/Resins

recommended for use with only Polyken coating systems. The liquid Solvent V.M. & P Naptha
adhesive systems consist of butyl based elastomers blended with Total Solids 30 %
polymeric resins dissolved in an organic solvent system. They can be
Weight/Gallon 6.76 lb
used for machine or hand brush applications and provide excellent
Weight/Liter 0.81 kg
adhesion to the pipe substrate and cathodic disbondment resistance.
Viscosity Medium Syrup
Liquid adhesive system is ideal for hand brush application to rough, Flash Point 4C (40F)
reconditioned, or grit-blasted pipe surfaces. It provides a uniformly VOC 0.59 kg/l (4.9 lb/gal)
smooth, instant tack surface for Polyken coating systems. Shelf Life 3 years
Coverage rate 300 ft/gallon
Caution: (estimated/varies) 7.38 m/liter
Store away from heat source. Read all label instructions prior to use.
Properly stored, all Polyken liquid coating systems have a shelf life of
3 years. Please request an application specification and storage
guideline from Seal For Life.
Polyken liquid adhesive systems are FLAMMABLE MIXTURES.
Features:
Excellent adhesion
Excellent cathodic disbondment resistance
Conforms to local and national standards
Benefits:
Ensures permanent bond of coating system
Provides long term corrosion prevention
Product selection guide

Max. operating temperature 93C (200F)
Additional mechanical layer Subsequent Polyken coating
systems
Compatible line coatings Carbon steel, PE, FBE, PP,CTE,
Tape,
Recommended pipe preparation SSA-ST2 (SSPC-SP3) or
SSA-SA 2 (SSPC-SP6)
1 3 mil anchor profile
(25 76 micron anchor profile)
Performance AWWA, DIN, EN standards
Product construction
1027
Adhesive color Black
Ordering information
Description
1027-LIQUID ADH 1 quart
1027-LIQUID ADH 1 gallon
1027-LIQUID ADH-4.75 gallon-18L
1027-LIQUID ADH 55 gallon
For other ordering options please contact your Seal For Life representative.
PDS-POLYKEN-1027-V1-AUG17-AARPS-0972 Page 1 / 2
PRODUCT DATA SHEET POLYKEN 1027
Application instruction: Job preparation Handling and commissioning

Tools, equipment Temperature gauge, DFT/WFT gauge Primer Exposure to loads Objects coated with Polyken 1027 should not
and auxiliaries application equipment/agitator, be exposed to loads e.g. from supports- or lifting
Additional coating Subsequent Polyken coating systems, 933-25, equipment.
materials 931, 939 Backfill Backfill is possible immediately after completion
High humidity Polyken 1027 can be applied in a humid of the coating application and after the
atmosphere. The substrate should be free from subsequent Polyken coating system has been
condensing water which can be reached by applied. Consult application guidelines for
keeping the temperature at least 5F (3C) specific instructions. Backfill should be clean and
above dew point. not contain any foreign items that can cause
Work area and The substrate surface should be dry, clean and damage to the coating system.
substrate protected against negative weather influences.
Product conditions The Polyken 1027 shall be stored and/or Information
transported in a dry, ventilated location. Storage Documentation Extensive information is available on our web-
temperature shall be a minimum of 60F (16C) site. Application instructions and other
and a maximum of 125F (52C).The minimum documentation can be obtained by contacting
primer temperature for application will be 60F our offices, from our local distributor or by
(16C). sending an email to [email protected]
Certified staff Application of the described coating system
Application instruction: Surface preparation should be carried out by certified personnel.
General The area to be coated has to be clean, dry, and
free from oil, grease and dust. All contamination
including mill-scale has to be removed.
Degreasing Degrease surfaces with Toluene or Heptane and
e.g. a lint-free cloth.
Preventing Prior to and during the application, the
condensation of temperature of the substrate(s) must be at least
water 5F (3C) above the dew point.
Substrate Temperature of the substrate should preferably
temperature be between +68F and +104F (+20C / +40C).
Preheating may be required.
Application instruction: Brief version

Step 1 Clean substrate to SSA-ST2, SSPC-SP3 (power
wire brush) or SSA-SA 2, SSPC-SP6
(commercial blast). Surface (anchor) profile
depth shall be no less than 1.0 mils (25 micron)
and no greater than 3 mils (76 micron).
Step 2 Uniform primer application achieving 2 to 3 mil
WFT. Primer should be dry to touch before
application of inner layer.
* For further detailed information, please view the corresponding Application
Guideline *
PDS-POLYKEN-1027-V1-AUG17-AARPS-0972

PDS-POLYKEN-1027-V1-AUG17 - AARPS-0972 Prymer

Uploaded by

Copyright:

Available Formats

PDS-POLYKEN-1027-V1-AUG17 - AARPS-0972 Prymer

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

PDS-POLYKEN-1027-V1-AUG17 - AARPS-0972 Prymer

Uploaded by

Copyright:

Available Formats

PRODUCT DATA SHEET

Product description: Polyken liquid adhesive systems are Base Rubber/Resins

Product selection guide

Application instruction: Job preparation Handling and commissioning

Application instruction: Brief version

You might also like