Pulse Compression

Pulse compression is a generic term that is used to describe a waveshaping process that is
produced as a propagating waveform is modified by the electrical network properties of the
transmission line. The pulse is frequency modulated, which provides a method to further
resolve targets which may have overlapping returns. Pulse compression originated with the
desire to amplify the transmitted impulse (peak) power by temporal compression. It is a
method which combines the high energy of a long pulse width with the high resolution of a
short pulse width. The pulse structure is shown in the figure 1.

Figure 1: separation of frequency modulated pulses

Since each part of the pulse has unique frequency, the returns can be completely separated.

This modulation or coding can be either

• FM (frequency modulation)
o linear (chirp radar) or
o non-linear or
• PM (phase modulation).

Now the receiver is able to separate targets with overlapping of noise. The received echo is
processed in the receiver by the compression filter. The compression filter readjusts the
relative phases of the frequency components so that a narrow or compressed pulse is again
produced. The radar therefore obtains a better maximum range than it is expected because of
the conventional radar equation.

Figure 2: short pulse (blue) and a long pulse with intrapulsemodulation (green)

The ability of the receiver to improve the range resolution over that of the conventional
system is called the pulse compression ratio (PCR). For example a pulse compression ratio of
50:1 means that the system range resolution is reduced by 1/50 of the conventional system.
The pulse compression ratio can be expressed as the ratio of the range resolution of an
unmodulated pulse of length τ to that of the modulated pulse of the same length and
bandwidth B.

(c0 · τ /2)
PCR = = B · τ (1)
(c0 / 2B)

This term is described as Time-Bandwidth-product of the modulated pulse and is equal to the
Pulse Compression Gain, PCG, as the gain in SNR relative to an unmodulated pulse.
Alternatively, the factor of improvement is given the symbol PCR, which can be used as a
number in the range resolution equation, which now achieves:

Rres = c0 · (τ / 2) · PCR = c0 /2 B (2)

The compression ratio is equal to the number of sub pulses in the waveform, i.e., the number
of elements in the code. The range resolution is therefore proportional to the time duration of
one element of the code. The radar maximum range is increased by the fourth root of PCR.

The minimum range is not improved by the process. The full pulse width still applies to the
transmission, which requires the duplexer to remained aligned to the transmitter throughout
the pulse. Therefore Rmin is unaffected.

Advantages Disadvantages
lower pulse-power high wiring effort
therefore suitable for Solid-State-amplifier
higher maximum range bad minimum range
good range resolution time-sidelobes
better jamming immunity
difficulter reconnaissance

Table 1: Advantages and disadvantages of the pulse compression

Pulse compression with linear FM waveform

At this pulse compression method the transmitting pulse has a linear FM waveform. This has
the advantage that the wiring still can relatively be kept simple. However, the linear frequency
modulation has the disadvantage that jamming signals can be produced relatively easily by so-
called „Sweeper”.

The block diagram on the picture illustrates, in more detail, the principles of a pulse
compression filter.
 Figure 3: Block diagram (an animation as explanation of the mode of operation

The compression filter are simply dispersive delay lines with a delay, which is a linear
function of the frequency. The compression filter allows the end of the pulse to „catch up” to
the beginning, and produces a narrower output pulse with a higher amplitude.

Filters for linear FM pulse compression radars are now based on two main types.

• Digital processing (following of the A/D- conversion).

Figure 4: View of the Time-Side-Lobes

Time-Side-Lobes

The output of the compression filter consists of the compressed pulse accompanied by
responses at other times (i.e., at other ranges), called time or range sidelobes. The figure
shows a view of the compressed pulse of a chirp radar at an oscilloscope and at a ppi-scope
sector.Amplitude weighting of the output signals may be used to reduce the time sidelobes to
an acceptable level. Weighting on reception only results a filter „mismatch” and some loss of
signal to noise ratio.

The sidelobe levels are an important parameter when specifying a pulse compression radar.
The application of weighting functions can reduce time sidelobes to the order of 30 db's.

Pulse compression with non-linear FM waveform

The non-linear FM waveform has several distinct advantages. The non-linear FM waveform
requires no amplitude weighting for time-sidelobe suppression since the FM modulation of
the waveform is designed to provide the desired amplitude spectrum, i.e., low sidelobe levels
of the compressed pulse can be achieved without using amplitude weighting.

Matched-filter reception and low sidelobes become

A symmetrical waveform has a frequency that increases

The disadvantages of the non-linear FM waveform are

• Greater system complexity

Figure 6: A symmetrical waveform (Output of the

Figure 7: non-symetrically
waveform
Phase-Coded Pulse Compression

Figure 8: diagram of a phase-coded pulse compression

Phase-coded waveforms differ from FM waveforms in that the long pulse is sub-divided into
a number of shorter sub pulses. Generally, each sub pulse corresponds with a range bin. The
sub pulses are of equal time duration; each is transmitted with a particular phase. The phase of
each sub-pulse is selected in accordance with a phase code. The most widely used type of
phase coding is binary coding.

The binary code consists of a sequence of either +1 and -1. The phase of the transmitted
signal alternates between 0 and 180° in accordance with the sequence of elements, in the
phase code, as shown on the figure. Since the transmitted frequency is usually not a multiple
of the reciprocal of the sub pulsewidth, the coded signal is generally discontinuous at the
phase-reversal points.

Length of Peak-sidelobe
Code elements
code n ratio, dB
2 +- -6.0
3 ++- -9.5
4 ++-+ , +++- -12.0
5 +++-+ -14.0

7 +++--+- -16.9

11 +++---++--+- -20.8
13 +++++--++-+-+ -22.3

Table: Barker Codes

The selection of the so called random 0, π phases is in fact critical. A special class of binary
codes is the optimum, or Barker, codes. They are optimum in the sense that they provide low
sidelobes, which are all of equal magnitude. Only a small number of these optimum codes
exist. They are shown on the beside table. A computer based study searched for Barker codes
up to 6000, and obtained only 13 as the maximum value.
It will be noted that there are none greater than 13 which implies a maximum compression
ratio of 13, which is rather low. The sidelobe level is -22.3 db.