Connecting Flexi Multiradio Extension System Module (FSMD/E) to th... https://intra-online.networks.nokia.com/pic/infocenterproxy/ru50_ep1_is...

WCDMA RAN, Rel. RU50 and RU50 EP1, Operating Documentation, Issue 07 (HTML) > Install > BTS > Flexi Multiradio 10 BTS >
Cabling Flexi Multiradio 10 Base Station

Connecting Flexi Multiradio Extension System Module (FSMD/E) to

the Master System Module (FSMF)
Purpose
Using FSME as an Extension System Module to FSMF is possible with the RAN2732 feature. For information on
the feature requirements, see RAN2732: Flexi System Module Extension, FSMF + FSMD/E.
Table: Connection requirements describes the interfaces that have to be connected between FSMF Master
System Module and the Extension System Module.

NOTICE: For OBSAI use two Multimode FSFL or FUFAS cables with 3 Gb SFP FOSG and a max distace of 2 m.
For more information on FSFL cables, see Table 103 Multi-mode fibers 90-90 OM2 in Flexi Multiradio Base Station and Flexi Multiradio 10 Base
Station Optional Items Description.

For more information on FOSG, see Table 110 3 Gb SFPs in Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items
Description.

Note: In this configuration, RF Modules and Remote Radio Heads must be connected to Master System Module RF/EXT ports: 1-3.

Table: Connection requirements

Connection number Master System Module port Extension System Module port

First connection (OBSAI) One of: One of:

EIF2*/RF/EXT6 OPT/EXT1

RF/EXT1, RF/EXT2, RF/EXT3 OPT/EXT2

First FBBA RF/EXT

Second FBBA RF/EXT

Second connection (OBSAI) One of: One of:

EIF2*/RF/EXT6 OPT/EXT1

RF/EXT1, RF/EXT2, RF/EXT3 OPT/EXT2

First FBBA RF/EXT

Second FBBA RF/EXT

Third connection (DC power)1 FPFD DC output DC input terminals on Flexi Power Distribution and
Fuses (FPFx) submodule

*Note that if ESM is connected to MSM EIF2 port, flag Enable FSM EIF2 as RP3-01 interface should be checked during commissioning.

1)Power supply can be also delivered from an external power source.

Before you start
WARNING! Invisible laser beam can cause eye damage.

Make sure that the laser beam is switched off when optical cables are installed.

WARNING! CAUTION! Risk of personal injury.

Always stop transmission before detaching the optical fiber from an optical fiber connector marked with a warning triangle.

NOTICE: NOTICE: Incorrect cables and seals may not provide appropriate ingress protection. Use only tested IP65 class outdoor cables with seals
provided by Nokia. This is required for both indoor and outdoor installations, including the outdoor cabinet.

NOTICE: NOTICE: Overbending damages the the optical fiber cables and can also cause connectors to detach or become damaged. Do not bend
optical fibre cables to a radius smaller than the minimum radius of 70 mm (2.76 inches) for cables with a diameter 7 mm (0.28 inches) or 50 mm (1.97

1 of 4 2/25/2016 12:25 PM
Connecting Flexi Multiradio Extension System Module (FSMD/E) to th... https://intra-online.networks.nokia.com/pic/infocenterproxy/ru50_ep1_is...

inches) for cables with a diameter 5 mm (0.20 inches).

NOTICE: Optical cables are fragile. Always route the optical cable according to the cables' natural alignment.

NOTICE: NOTICE: Optical fibers are sensitive. Possible contamination lowers the mechanical strength of the optical fiber, which dampens the
transmission of light in the fibers. Clean all optical fiber connectors before installation using an optical fibers connector cleaning kit.

NOTICE: NOTICE: RF module is required to be set into disabled state by way of Blocking RF unit or Base Station Site prior to new or replacement
SFP insertion to RF HW.

NOTICE: Changing OBSAI MSM-ESM connection port numbers in runtime is not supported at any end.

NOTICE: When FSMD/E is added as an extension module to the BTS, it is mandatory to reconfigure the BTS.

Procedure

1 Install the System Extension Module casing.

In stacked installations, the System Extension Module is installed on top of the module stack.

NOTICE: Risk of damage to the equipment. If you are reusing a Master System Module as a System Extension Module, remove the transmission
sub-module prior to installation.

Figure: Location of the System Extension Module in stacked installations

2 of 4 2/25/2016 12:25 PM
Connecting Flexi Multiradio Extension System Module (FSMD/E) to th... https://intra-online.networks.nokia.com/pic/infocenterproxy/ru50_ep1_is...

2 Install two optical transceivers to the Master System Module and two further optical transceivers to the System Extension Module (for the
first two connections described in Table: Connection requirements).

For further information on how to install the optical transceivers for System Module variant FSMF, see Connecting internal optical cables. For FSMD and
FSME variants, see Connecting internal optical cables in the Cabling Flexi Multiradio BTS LTE document.

3 Firstly, connect an optical cable from the Master System Module chosen optical port to the OPT-EXT1 or OPT-EXT2 port on the System
Extension Module, as described in Table: Connection requirements.

Make sure that all connector seals are secured firmly.

4 Repeat step for the second optical cable.

5 Connect one end of the DC cable to the System Extension M odule DC connector and the other end to the connector marked with EXT on
the System Module front panel.

Route the DC cable via external cable entries. Fix any excess cable on the sides of the module casings.

Note: Do not feed the power supply from the Extension Module to the RF modules as this can cause a power overload.

For information on connecting FMSF DC cables, see Connecting external power feed.

Result
Figure: Connecting System Extension Module cables shows the example cables connection between master and
extension module.

Figure: Connecting System Extension Module cables

3 of 4 2/25/2016 12:25 PM
Connecting Flexi Multiradio Extension System Module (FSMD/E) to th... https://intra-online.networks.nokia.com/pic/infocenterproxy/ru50_ep1_is...

Note: For more information on FSFL cables, see Table 103 Multi-mode fibers 90-90 OM2 in Flexi Multiradio Base Station and Flexi Multiradio 10
Base Station Optional Items Description.
For more information on FOSG, see Table 110 3 Gb SFPs in Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items
Description.

Id: DN09107822 2015 Nokia Solutions and Netw orks. All rights reserved.

4 of 4 2/25/2016 12:25 PM