Scribd
Upload
3K views

RVC-12 Power Factor Controller Programing

The RVC is a user-friendly power factor controller with the following features: 1. It provides easy commissioning through automatic setting of parameters like phase shift, starting current, number of outputs, and switching sequence. 2. It has a highly efficient switching strategy that reduces capacitor switching and avoids unnecessary intermediate steps to increase capacitor lifetime. 3. It is suitable for environments up to 70°C and is insensitive to voltage fluctuations and harmonics in the system.

Uploaded by

Ronald H Santos
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
3K views

RVC-12 Power Factor Controller Programing

The RVC is a user-friendly power factor controller with the following features: 1. It provides easy commissioning through automatic setting of parameters like phase shift, starting current, number of outputs, and switching sequence. 2. It has a highly efficient switching strategy that reduces capacitor switching and avoids unnecessary intermediate steps to increase capacitor lifetime. 3. It is suitable for environments up to 70°C and is insensitive to voltage fluctuations and harmonics in the system.

Uploaded by

Ronald H Santos
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Power Factor Controller RVC

The user-friendly PF controller


RVC : The user-friendly PF controller

LCD Display Indicates a demand for


switching on/off a capacitor
step

Special features icons

Active outputs

Inductive/capacitive PF
Alarm Programmable parameters :
Overtemperature
Target Power Factor (cos )
C/k (starting current)
Phase shift (for special connections)
Switching delay times
Number of active outputs
Switching sequence
Key pad

Automatic / manual set mode

Automatic setting of : Easy commissioning with automatic recognition of :


Phase shift Special connections (single-phase, CT leads)
C/k Number of outputs
Number of outputs Type of switching sequence
Type of switching sequence

Powerful features
Easy commissioning.
Complete auto set-up (starting current-C/k, number of active outputs, type of switching sequence, phase
shift, special connections).
Easy to use thanks to a user-friendly interface and ease of access to parameters for manual setting.
Highly efficient switching strategy combining integral, direct and circular switching.
This allows to : control the cos in presence of rapidly varying loads,
reduce the number of switching,
avoid unnecessary intermediary switchings,
increase the lifetime of the capacitors and contactors.
Suitable for hot environments thanks to max. ambient temperature rating of 70C.
Insensitivity to the presence of harmonics.
Overvoltage and undervoltage protection.
Alarm : an alarm contact is closed when the target cos is not reached within 6 minutes after all outputs
have been switched on, the internal temperature of the RVC rises above 85C or the power supply is out of
range.

2
Easy commissioning

The AUTO SET mode allows the RVC commissioning in only 2 simple steps :

Activation of the automatic setting of : Setting


Phase shift of the target cos
C/k
Number of outputs
Switching sequence

and or

Easy programming

All parameters are easily accessible


for manual setting.

3
Technical specification

Measuring system: Mode of switching:


micro-processor system for balanced three-phase networks or single- the mode of switching for all the programmable switching sequences is
phase networks. integral, direct, circular or linear.
Operating voltage: Saving-function:
100V to 120V, 220V to 240V, 380V to 440V depending on type of RVC. all programmed parameters and modes are saved in a non-volatile
Voltage tolerance: memory.
+/- 10% on indicated operating voltages. Power outage release:
Frequency range: quick automatic disconnection in less than 20ms (50Hz) in case of power
50 or 60 Hz +/- 5% (automatic adjustment to network frequency). outage or voltage drop.
Current input: Power outage reset delay time:
5A (RMS). 40 s.
Current input impedance: Alarm contact:
<0.1 Ohm. - normally closed contact;
Consumption: - max. continuous current : 5A;
15 VA max. - rated/max. breaking voltage: 250Vac/440Vac.
Output contact rating: Overvoltage and undervoltage protection
-max. continuous current: 1.5 A; Autoadaptation to the phase-rotation of the network and the
-max. peak current: 5 A; CT-terminals.
-max. voltage: 440 Vac; Insensitivity to harmonics.
-terminal A is rated for a continuous current of 16 A. Working with generative and regenerative loads.
Power Factor setting: LCD contrast automatically compensated with temperature.
from 0.7 inductive to 0.7 capacitive. Operating temperature:
Starting current setting (C/k): -10 C to 70 C.
0.05 to 1A. Storage temperature:
Automatic measurement of C/k. - 30 C to 85 C.
Number of outputs: Mounting position:
RVC-3 (400V only): programmable up to 3 outputs. vertical panel mounting.
RVC-6: programmable up to 6 outputs.
RVC-8 (400V only): programmable up to 8 outputs. Dimensions:
RVC-10 (400V only): programmable up to 10 outputs. 144x144x80 mm (hxwxd).
RVC-12: programmable up to 12 outputs. Weight:
Switching time between steps: 0.8 kg (unpacked).
programmable from 1s to 999s (independent of reactive load). Connector:
Switching sequences: WAGO.
1:1:1:1:1:...:1 1:2:2:2:2:...:2 Front plate protection:
1:2:4:4:4:...:4 1:2:4:8:8:...:8 IP40.
1:1:2:2:2:...:2 1:1:2:4:4:...:4 Relative humidity:
1:1:2:4:8:...:8 1:2:3:3:3:...:3 maximum 95%, non-condensing.
1:2:3:6:6:...:6 1:1:2:3:3:...:3 CE Marked.
1:1:2:3:6:...:6

Wiring diagram

k, l: leads of the current transformer


L2, L3: 2 of the 3 phases (not monitored by the CT)
M1, M2: leads of the normally closed contact
A: output relay common source
1-12: outputs
2GCS301015A0050

While all care has been taken to ensure that the information contained in this publication is correct, no responsibility can be accepted
for any inaccuracy. We reserve the right to alter or modify the information contained herein at any time in the light of technical or other
developments. Technical specifications are valid under normal operating conditions only. We do not accept any responsibility for
www.abb.com/lowvoltage any misuse of the product and cannot be held liable for indirect or consequential damages.

You might also like