Scribd
Upload
103 views

Incremental Encoder Output Signal Overview

The document discusses different types of incremental encoder output signals, including push-pull output, RS422 output, and quadrature output signals. Push-pull output provides signal levels equal to the supply voltage, while RS422 uses balanced differential line drivers for noise immunity. Quadrature encoder outputs use the 90 degree phase shift between channels A and B to determine shaft rotation direction and velocity.

Uploaded by

mica
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
103 views

Incremental Encoder Output Signal Overview

The document discusses different types of incremental encoder output signals, including push-pull output, RS422 output, and quadrature output signals. Push-pull output provides signal levels equal to the supply voltage, while RS422 uses balanced differential line drivers for noise immunity. Quadrature encoder outputs use the 90 degree phase shift between channels A and B to determine shaft rotation direction and velocity.

Uploaded by

mica
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Incremental Encoder Output

Signal Overview

Introduction Push-Pull Output

The output signals of incremental rotary encoders The Push-Pull type output is an option that provides
incorporate two channels to indicate rotation of the encoder output signal levels that are equal to the
encoder shaft plus a zero marker pulse channel. voltage supply in amplitude and referenced to the
These A and B channels (quadrature) are defined as power supply common voltage (0V) level. These
pulses per revolution (ppr) and define the smallest signals are driven by transistor outputs such that
rotational angular position of the shaft that can be a high level output is equal to the power supply
resolved. Since these signals are in quadrature level (+Ub), in effect pushing or sourcing the output
mode, 90-degree phase shift relative to each other, signal to the load. The low level output is equal
they can also be used to determine the direction of to the power supply common voltage (0V) level, in
the encoder shaft. The zero marker pulse channel, Z effect pulling or sinking the load. The power supply
or 0, is a once-per-revolution pulse that can be used levels for push-pull type encoders are typically in the
to indicate a zero or home position relative to a single range of 10 to 30 VDC. The T-Line encoder series
revolution of the encoder. with push-pull output can be powered in the range
of 4.75 to 30 VDC, giving the user further flexibility in
powering the encoder device. Push-pull output types
can be connected as single ended (A, B, Z) or as
differential connections (A /A, B /B, Z /Z).

+Ub

B
B

+Ub

+Ub
B

0V

0V
Part No. TDOCT-B0C7_ENG

1
Incremental Encoder Output
Signal Overview

RS422 Output

RS422 output types are typically referred to as


balanced differential line driver outputs, whose
characteristics are determined by the EIA standard
that defines the electrical specification and signal
characteristics (voltage levels, slew rates, etc.) as
well as transmission rates. This signal type is always
used as differential pairs of signals (A,/A;) (B,/B;)
(Z,/Z) and the encoder output signal is generated
by components that conform to the RS422 standard.
Differential RS422 line driver outputs inherently
provide a level of noise immunity since the encoder
signals are evaluated at the receiver end as
differential levels. Therefore, common mode noise
imposed on the signals will be cancelled via this
differential mode evaluation of the receiving circuitry.
Signal levels with this type of interface circuitry are
defined as high output signal when output is 2.5 V,
and low output signal, when output is 0.5 V when
referenced to power supply common. Along with the
inherent noise immunity of RS422 line driver outputs,
these outputs also offer the advantages of higher
output frequencies because of the driver/receiver
requirements and cabling characteristics.

/A

A
Noise imposed on the signal
levels is effectively cancelled by
Part No. TDOCT-B0C7_ENG

the line receiver input circuit.


/A

2
Incremental Encoder Output
Signal Overview

Quadrature Output Signals

The output from incremental rotary encoders is


known as a quadrature signal. Quadrature en-
coder output signals are defined by the phase
shift relationship between the A channel and the B
channel signals. This phase relationship (90 phase
shift) provides the information required so that the
encoder shaft direction as well as the velocity of
the encoder shaft can be determined. The direction
of the encoder shaft can be determined by evalua-
tion of the A or B signal level. The direction CW or
CCW can be determined by evaluating the signal
levels relative to the alternate channel at the time of
the rising edge.

A A

B B

t t
Channel A rising edge occurs Channel B rising edge occurs before
before Channel B rising edge (Ch B Channel A rising edge. (Ch A is low
is low value on CH A rising edge) value on CH B rising edge)

David Rubinski
Product Marketing Manager
Sensors/Installation Products
Pepperl+Fuchs
Twinsburg, OH
330-486-0001
www.pepperl-fuchs.us
[email protected]
Part No. TDOCT-B0C7_ENG

You might also like