TRANS-AMF

AUTOMATIC MAINS FAILURE UNIT

1. Introduction
1.1 General Specifications
The unit provides for automatic transfer of a load from mains to generator in the event of a mains
failure. Intended for unattended operation, it is able to detect failure of any phase of the mains and to
start and switch over to a generator if the mains voltage goes outside pre-set limits. Both automatic
and manual control is possible. A test mode is also available which allows the generator to be run
without taking the load.
The unit has Dual Working feature. In the event of a mains failure, group with high priority starts and
takes the load. If both groups has no priority, the group with less working hour will start and take the
load. To use Dual Working feature Dual Set expansion module must be used.
The unit calculates engine RPM from Magnetic Pickup sensor (MPU) and/or generator voltage signal.
The unit monitors J1939 ECU messages and provides remote start/stop control via J1939 protocol
(supported ECUs: Volvo EMS2, Volvo EDC4, Perkins, Scania S6, MAN MFR and standard messages).
The unit monitors generator operation and gives warning of any faults that are detected.
The configurable input-3 can be used as the water level sensing input.
The configurable input-7 can be used as the cabin temperature analog input.

1.2 Warranty
EMKO Elektronik warrants that the equipment delivered is free from defects in material and workmanship.
This warranty is provided for a period of two years. The warranty period starts from the delivery date. This
warranty is in force if duty and responsibilities which are determined in warranty document and instruction
manual performs by the customer completely.

1.3 Maintenance
Repairs should only be performed by trained and specialized personnel. Cut power to the device before
accessing internal parts.
Do not clean the case with hydrocarbon-based solvents (Petrol, Trichlorethylene etc.). Use of these
solvents can reduce the mechanical reliability of the device. Use a cloth dampened in ethyl alcohol or
water to clean the external plastic case.
Introduction Brochure. ENG TRANS-AMF 01 V22 02/15
 2. Installation
indekiler

! Before beginning installation of this product, please read the instruction

manual and warnings below carefully.

A visual inspection of this product for possible damage occured during shipment is
recommended before installation. It is your responsibility to ensure that qualified mechanical
and electrical technicians install this product.

If there is danger of serious accident resulting from a failure or defect in this unit , power off
the system and seperate the electrical connection of the device from the system.

Keep the power off until all of the wiring is completed so that electric shock and trouble with
the unit can be prevented.

2.1 Unit Configuration

indekiler

The unit can be programmed using the buttons and LCD display on the front panel or PC
Software.

2.2 Panel Mounting

indekiler

The unit is designed for panel mounting. Fixing is by two screw fixings.
1- Insert the unit in the panel cut-out from the front.
2- Insert the fixings in the slotted at the corners of the unit and tighten the fixing screws to secure
the unit against the panel.

! During the equipment is putted in hole on the metal panel while mechanical
installation some metal burrs can cause injury on hands, you must be careful.

152mm

135mm

182mm
229mm

Figure 2.1 Front View Figure 2.2 Panel Cut-Out

2
2.3 Electrical Connection
TRANS-AMF three phase connections schematic

BATTERY -

22 21
17 18 19 20
-(SCR) +

USB
MPU

!
!

1
3
FUSE-7
BATTERY +

H(+) L(-) SCR

J1939 ECUs

! 2
N
L1
L2
L3
GENERATOR

! 4

11 12 13 14 15 16

27 26 25 24 23
Configurable Analog Input-2

* * * *
Oil Sender

Temperature Sender

FROM THE PROGRAM

AS A DIGITAL INPUT
IT CAN BE USED
Level Sender or

BY SELECTING
Configurable Analog Input-1

PARAMETERS
To Engine
Sender Common Earth

BATTERY -
*
Max. 300VV
5

FUSE-6 Emergency Stop or

4

Configurable Input-1

35 34 33 32 31 30 29 28
FUSE-5
Configurable Input-2
3

FUSE-4 Water Level or

Configurable Input-3
2

Low Oil Pressure or

Configurable Input-4
Mechanical interlock

8A High Temperature or
1

Configurable Input-5
Generator Configurable Input-6
Contactor
Relay
G

Cabin Temperature or
Electrical interlock

Configurable Input-7
D+(W.L.)
LOAD

Charge Alt.
BATTERY +
M

Mains Fuel Or
TRANSISTOR OUTPUTS

Contactor Configurable Output-1

39 38 37 36

Relay Crank Or
10

Configurable Output-2
8A
Configurable Output-3
MAX. 1 A

FUSE-3
Configurable Output-4
9
Max. 300VV

FUSE-2
8

FUSE-8 BATTERY +
42 41 40

FUSE-1
7

5A
Configurable Output-5
MAINS

5A
Configurable Output-6
L1
L2
L3
N

FUSE-1, FUSE-2, FUSE-5, FUSE-6 2 A. T FUSE-3, FUSE-4 8 A. T

FUSE-7 6 A. T
FUSE-8 Max. 10 A. T
1- Connect the unit as shown in the appropriate diagram. Be sure to connect the battery

!
supply the right way round and battery negative should be grounded.
2- The CAN interface requires that a 120 Ohms terminator is fitted to each end of the
communications link. This termination resistor is fitted internally into the unit. So it is not
required externally. The screen is grounded at one end ONLY.
3- Screened cable must be used for connecting the Magnetic Pickup, ensuring that the
screen is grounded at one end ONLY.
4- Current transformers secondary should be grounded.
3
3. Changing And Saving Parameters Values
Operation Screen
MAINS PROGRAM
V12: 380V V1: 220V Operator setting Press the Up or
V23: 380V V2: 220V Technician setting Down buttons to
V31: 380V V3: 220V Factory adjustment
Wait for start select the section
you wish to
view/change.
When the Prog button is
pressed, the parameters
section is asked for
accessing to parameters.

PROGRAM TECHNICIAN SETTING

Operator setting Password
Technician setting
Factory adjustment 0000 Enter password
Press the with cursor (Right,
Enter Left, Up and
button. Down) buttons.

TECHNICIAN SETTING TECHNICIAN SETTING

Password System Press the Up or
Mains Down buttons to
0162 Generator
Engine select the main
parameter group
Press the Enter button to confirm you wish to
Note1: If Enter button is pressed password. If the password is view/change.
and the technician password is incorrect, the unit will drop out of
zero, Password screen is ignored. program mode.

TECHNICIAN SETTING GENERATOR

System Volt level
Mains Frequency level
Generator Current level & act.
Engine Power level
Press Enter button to access to
all parameters page in currently Press Enter button to
main parameter group. access to all parameters in
currently parameter page.

GENERATOR VOLT LEVEL GENERATOR VOLT LEVEL

Under volt shutdown Under volt shutdown Parameter can be
Under volt prealarm 320 Vac changed with Up
Under volt reset and Down buttons.
Over volt shutdown
Press the Enter
button to view
parameter value.

GENERATOR VOLT LEVEL GENERATOR VOLT LEVEL

Under volt shutdown Under volt shutdown
325 Vac Under volt prealarm
Under volt reset
Over volt shutdown
Press Enter button to
confirm the changed value. To exit from
programming mode any
time, press Prog button.
When the Escape button is
GENERATOR pressed any time, previous MAINS Operation
Volt level page can be accessed. V12: 380V V1: 220V Screen
Frequency level V23: 380V V2: 220V
Current level & act. V31: 380V V3: 220V
Power level Wait for start

4
4. Parameters
4.1 Operator Parameters
4.1.1 Mains

MAINS VOLT LEVEL (Mains->Volt level) Min Max Default Unit

Under volt trip Mains Under Voltage 60 600 320 VV
Under volt reset Mains Under Voltage Reset 60 600 340 VV
Over volt trip Mains Over Voltage 60 600 440 VV
Over volt reset Mains Over Voltage Reset 60 600 420 VV

MAINS FREQ. LEVEL (Mains->Frequency level) Min Max Default Unit

Under freq trip Mains Under Frequency 20.0 75.0 45.0 Hz
Under freq reset Mains Under Frequency Reset 20.0 75.0 48.0 Hz
Over freq trip Mains Over Frequency 20.0 75.0 55.0 Hz
Over freq reset Mains Over Frequency Reset 20.0 75.0 52.0 Hz

4.1.2 Generator

GENERATOR VOLT LEVEL (Generator->Volt level) Min Max Default Unit

Under volt shutdown Generator Under Voltage Shutdown 60(dis) 600 320 VV
Under volt prealarm Generator Under Voltage Pre-Alarm 60(dis) 600 340 VV
Under volt reset Generator Under Voltage Pre-Alarm Reset 60 600 350 VV
Over volt shutdown Generator Over Voltage Shutdown 60 600 440 VV
Over volt prealarm Generator Over Voltage Pre-Alarm 60(dis) 600 420 VV
Over volt reset Generator Over Voltage Pre-Alarm Reset 60 600 400 VV
Shutdown delay time Generator Voltage Shutdown Delay Time 0.0 10.0 1.0 Sec

GENERATOR FREQ LEVEL (Generator->Frequency level) Min Max Default Unit

Nominal frequency Nominal Alternator Frequency 30.0 75.0 50.0 Hz
Under freq shutdown Generator Under Frequency Shutdown 30.0(dis) 75.0 43.0 Hz
Under freq prealarm Generator Under Frequency Pre-Alarm 30.0(dis) 75.0 45.0 Hz
Under freq reset Generator Under Frequency Pre-Alarm Reset 30.0 75.0 46.0 Hz
Over freq shutdown Generator Over Frequency Shutdown 30.0(dis) 75.0 58.0 Hz
Over freq prealarm Generator Over Frequency Pre-Alarm 30.0(dis) 75.0 55.0 Hz
Over freq reset Generator Over Frequency Pre-Alarm Reset 30.0 75.0 54.0 Hz
Shutdown delay time Generator Frequency Shutdown Delay Time 0.0 10.0 1.0 Sec

GENERATOR CUR LEVEL (Generator->Current level) Min Max Default Unit

Under cur. set Generator Under Current Set 0 9999 1 AV
Under cur. prealarm Generator Under Current Pre-Alarm 0(dis) 9999 dis AV
Under cur. reset Generator Under Current Pre-Alarm Reset 0 9999 5 AV
Over cur. IDMT alarm Generator Over Current IDMT Alarm ENABL/DISBL DISBL
Over cur. set Generator Over Current Set 0 9999 9999 AV
Over cur. prealarm Generator Over Current Pre-Alarm 0(dis) 9999 9990 AV
Over cur. reset Generator Over Current Pre-Alarm Reset 0 9999 9980 AV

Note: dis = disable

5
GEN POWER LEVEL (Generator->Power level) Min Max Default Unit
Under power set Generator Under Power Set 0 9999 0 kVA
Under power prealarm Generator Under Power Pre-Alarm 0(dis) 9999 dis kVA
Under power reset Generator Under Power Pre-Alarm Reset 0 9999 5 kVA
Over power set Generator Over Power Set 0 9999 0 kVA
Over power prealarm Generator Over Power Pre-Alarm 0(dis) 9999 dis kVA
Over power reset Generator Over Power Pre-Alarm Reset 0 9999 0 kVA
Reverse power set Reverse Power Set -9999 0 0 kW

GEN WORKING CALENDAR (Generator->Working calendar) Min Max Default Unit

Disable/enable select Working Calendar Disable or Enable DISBL/ENABL DISBL
Start time on monday Working Calendar Work Start Time on Monday 0.00 23.59 0.00 H.Min
Stop time on monday Working Calendar Work Stop Time on Monday 0.00 23.59 23.59 H.Min
Start time on tues. Working Calendar Work Start Time on Tuesday 0.00 23.59 0.00 H.Min
Stop time on tuesday Working Calendar Work Stop Time on Tuesday 0.00 23.59 23.59 H.Min
Start time on wednes. Working Calendar Work Start Time on Wednesday 0.00 23.59 0.00 H.Min
Stop time on wednes. Working Calendar Work Stop Time on Wednesday 0.00 23.59 23.59 H.Min
Start time on thurs. Working Calendar Work Start Time on Thursday 0.00 23.59 0.00 H.Min
Stop time on thursday Working Calendar Work Stop Time on Thursday 0.00 23.59 23.59 H.Min
Start time on friday Working Calendar Work Start Time on Friday 0.00 23.59 0.00 H.Min
Stop time on friday Working Calendar Work Stop Time on Friday 0.00 23.59 23.59 H.Min
Start time on satur. Working Calendar Work Start Time on Saturday 0.00 23.59 0.00 H.Min
Stop time on saturday Working Calendar Work Stop Time on Saturday 0.00 23.59 23.59 H.Min
Start time on sunday Working Calendar Work Start Time on Sunday 0.00 23.59 0.00 H.Min
Stop time on sunday Working Calendar Work Stop Time on Sunday 0.00 23.59 23.59 H.Min

4.2 Technician Parameters

4.2.1 System

SYSTEM NETWORK (System->Network) Min Max Default Unit

CT ratio Current Transformer Ratio 1 9999 100
Earth fault CT ratio Earth Fault Current Transformer Ratio 1 9999 100
PT ratio Voltage Transformer Ratio 1 100 1
Type of AC system Select AC system; 0- 1 Phase 2 Wire 0 3 1
1- 3 Phase 4 Wire
2- 2 Phase 3 Wire L1-L2
3- 2 Phase 3 Wire L1-L3
Phase sequence Generator Phase Sequence (dis, L123 or L321) DISBL, L123, L321 DISBL
Generator kVA rating Generator kVA rating set 0 9999 300 kVA
Power unit Power unit kVA/kW kVA
kVA,kW,kVAr point kVA, kW, kVAr point position; 0-> 0 0 3 0
1-> 0.0
2-> 0.00
3-> 0.000

Note: dis = disable

6
BREAKERS (System->Breakers) Min Max Default Unit
Type of Breaker Hardware Breaker Selection 0 2 0
Gen.brk.cls.contact Gen Close Breaker Contact Type NO / NC 0
Gen.brk.cls.relay Gen Close Breaker Relay Type NOR / PULS 0
Gen.brk.cls.time Gen Close Timer 1 250 5 Sec
Gen.brk.open relay Gen Open Breaker Relay Type NOR / PULS 0
Gen.brk.open time Gen Open Timer 1 250 5 Sec
Mains.brk.cls.contact Mains Close Breaker Contact Type NO / NC 0
Mains.brk.cls.relay Mains Close Breaker Relay Type NOR / PULS 0
Mains.brk.cls.time Mains Close Timer 1 250 5 Sec
Mains.brk.open relay Mains Open Breaker Relay Type NOR / PULS 0
Mains.brk.open time Mains Open Timer 1 250 5 Sec
Break.close puls.time Breaker Close Pulse Time 0.0 10.0 0.5 Sec
Break.open pulse time Breaker Open Pulse Time 0.0 10.0 0.5 Sec
Transfer time Transfer Time 0 250 2 Sec
Spring loading time Spring Loading Time 1 250 3 Sec
Retry number Retry Number 1 250 5

LCD DISPLAY (System->LCD display) Min Max Default Unit

Language Language Selection ENGLISH/CHINESE ENGLISH
Contrast Contrast Setting 4 9 5
Auto backlight off Auto Backlight Off ENABL/DISBL DISBL
Auto scroll time Auto Scroll Time 0 (dis) 250 0 Sec
Auto scroll number Auto Scroll Number 1 24 5
Err. mesg scroll time Scroll Time For Error Messages 1 250 2 Sec

COMMUNICATION (System->Communication) Min Max Default Unit

Slave address Slave Address 1 247 1
Baud rate Baud Rate: 0 - 1200 baud 0 5 3
1 - 2400 baud
2 - 4800 baud
3 - 9600 baud
4 - 19200 baud
5 - 38400 baud
Parity Parity: 0 - NONE 0 2 0
1 - ODD
2 - EVEN
Stop bit Stop Bit (0-> 1 stop bit,1-> 2 stop bit) 0 1 0
Datalog period Datalog Period 0.0(dis) 999.9 1.0 Min
Timeout Timeout 0(dis) 999 dis Min

DATE & TIME SET (System->Date & time set) Min Max Default Unit
Year Year 0 99
Month Month 1 12
Day Date 1 31
Week Day of week 1 7
Hour Hour 0 23
Minute Minute 0 59
Second Second 0 59
Note:
NO / NC : Normally Open / Normally Close
NOR / PULS : Normal / Pulse
dis = disable

7
DEFAULT SETTINGS (System->Default settings) Min Max Default Unit
Save setting to def. Save setting to default YES / NO NO
Reset default sets Reset default sets YES / NO NO
Reset factory sets Reset factory sets YES / NO NO

PASSWORD SETTINGS (System->Password settings) Min Max Default Unit

Operator password Operator Password 0 9999 0
Technician password Technician Password 0 9999 0

4.2.2 Mains
MAINS VOLT LEVEL (Mains->Volt level) Min Max Default Unit
Under volt trip Mains Under Voltage 60 600 320 VV
Under volt reset Mains Under Voltage Reset 60 600 340 VV
Over volt trip Mains Over Voltage 60 600 440 VV
Over volt reset Mains Over Voltage Reset 60 600 420 VV

MAINS FREQ. LEVEL (Mains->Frequency level) Min Max Default Unit

Under freq trip Mains Under Frequency 20.0 75.0 45.0 Hz
Under freq reset Mains Under Frequency Reset 20.0 75.0 48.0 Hz
Over freq trip Mains Over Frequency 20.0 75.0 55.0 Hz
Over freq reset Mains Over Frequency Reset 20.0 75.0 52.0 Hz

MAINS ACTIONS (Mains->Actions) Min Max Default Unit

Mains failure detect Mains Failure Detection En/Dis ENABL/DISBL ENABL
Mains fail.stop mode Look Mains Failure at Stop Mode En/Dis ENABL/DISBL ENABL
Always return delay Always Look Mains Return Delay ENABL/DISBL DISBL

4.2.3 Generator
GENERATOR VOLT LEVEL (Generator->Volt level) Min Max Default Unit
Under volt shutdown Generator Under Voltage Shutdown 60(dis) 600 320 VV
Under volt prealarm Generator Under Voltage Pre-Alarm 60(dis) 600 340 VV
Under volt reset Generator Under Voltage Pre-Alarm Reset 60 600 350 VV
Over volt shutdown Generator Over Voltage Shutdown 60 600 440 VV
Over volt prealarm Generator Over Voltage Pre-Alarm 60(dis) 600 420 VV
Over volt reset Generator Over Voltage Pre-Alarm Reset 60 600 400 VV
Shutdown delay time Generator Voltage Shutdown Delay Time 0.0 10.0 1.0 Sec

GENERATOR FREQ LEVEL (Generator->Frequency level) Min Max Default Unit

Nominal frequency Nominal Alternator Frequency 30.0 75.0 50.0 Hz
Under freq shutdown Generator Under Frequency Shutdown 30.0(dis) 75.0 43.0 Hz
Under freq prealarm Generator Under Frequency Pre-Alarm 30.0(dis) 75.0 45.0 Hz
Under freq reset Generator Under Frequency Pre-Alarm Reset 30.0 75.0 46.0 Hz
Over freq shutdown Generator Over Frequency Shutdown 30.0(dis) 75.0 58.0 Hz
Over freq prealarm Generator Over Frequency Pre-Alarm 30.0(dis) 75.0 55.0 Hz
Over freq reset Generator Over Frequency Pre-Alarm Reset 30.0 75.0 54.0 Hz
Shutdown delay time Generator Frequency Shutdown Delay Time 0.0 10.0 1.0 Sec

Note: dis = disable

8
GEN CUR LEVEL & ACT (Generator->Current level & act.) Min Max Default Unit
Under cur. set Generator Under Current Set 0 9999 1 AV
Under cur. prealarm Generator Under Current Pre-Alarm 0(dis) 9999 dis AV
Under cur. reset Generator Under Current Pre-Alarm Reset 0 9999 5 AV
Under cur. act. Generator Under Current Actions 0(dis) 3 dis
0 - Disable
1 - Warning (Alarm Only, No Shutdown)
2 - Electrical Trip (Alarm/Off Load Generator
Followed By Shutdown After Cooling)
3 - Shutdown (Alarm And Shutdown)
Under act. delay time Generator Under Current Actions Delay Time 0 99 2 Sec
Over cur. IDMT alarm Generator Over Current IDMT Alarm ENABL/DISBL DISBL
Over cur. set Generator Over Current Set 0 9999 9999 AV
Over cur. prealarm Generator Over Current Pre-Alarm 0(dis) 9999 9990 AV
Over cur. reset Generator Over Current Pre-Alarm Reset 0 9999 9980 AV
Over cur. act. Generator Over Current Actions 0(dis) 3 dis
0 - Disable
1 - Warning (Alarm Only, No Shutdown)
2 - Electrical Trip (Alarm/Off Load Generator
Followed By Shutdown After Cooling)
3 - Shutdown (Alarm And Shutdown)
Over act. delay time Generator Over Current Actions Delay Time 0 99 2 Sec
Short circuit cur. Generator Short Circuit Current Set 0 9999 9999 AV
Earth fault cur. Generator Earth Fault Current Set 0 9999 100 AV
Earth fault cur. act. Generator Earth Fault Current Actions 0(dis) 3 dis
0 - Disable
1 - Warning (Alarm Only, No Shutdown)
2 - Electrical Trip (Alarm/Off Load Generator
Followed By Shutdown After Cooling)
3 - Shutdown (Alarm And Shutdown)
E.F. act. delay time Generator Earth Fault Current Actions Delay Time 0 99 2 Sec
Unbalance load set Unbalance Load Set 0 9999 0 AV
Unbalance load act. Unbalance Load Actions 0(dis) 3 dis
0 - Disable
1 - Warning (Alarm Only, No Shutdown)
2 - Electrical Trip (Alarm/Off Load Generator
Followed By Shutdown After Cooling)
3 - Shutdown (Alarm And Shutdown)
Unbalance act. delay Unbalance Load Actions Delay Time 0 99 2 Sec

9
GEN POWER LEVEL (Generator->Power level) Min Max Default Unit
Under power set Generator Under Power Set 0 9999 0 kVA
Under power prealarm Generator Under Power Pre-Alarm 0(dis) 9999 dis kVA
Under power reset Generator Under Power Pre-Alarm Reset 0 9999 5 kVA
Under power act. Generator Under Power Actions 0(dis) 3 0(dis)
0 - Disable
1 - Warning (Alarm Only, No Shutdown)
2 - Electrical Trip (Alarm/Off Load Generator
Followed By Shutdown After Cooling)
3 - Shutdown (Alarm And Shutdown)
Under act. delay time Generator Under Power Action Delay Time 0 99 2 Sec
Over power set Generator Over Power Set 0 9999 0 kVA
Over power prealarm Generator Over Power Pre-Alarm 0(dis) 9999 dis kVA
Over power reset Generator Over Power Pre-Alarm Reset 0 9999 0 kVA
Over power act. Generator Over Power Actions 0(dis) 3 0(dis)
0 - Disable
1 - Warning (Alarm Only, No Shutdown)
2 - Electrical Trip (Alarm/Off Load Generator
Followed By Shutdown After Cooling)
3 - Shutdown (Alarm And Shutdown)
Over act. delay time Generator Over Power Action Delay Time 0 99 2 Sec
Reverse power set Reverse Power Set -9999 0 0 kW
Reverse power act. Reverse Power Actions 0(dis) 3 0(dis)
0 - Disable
1 - Warning (Alarm Only, No Shutdown)
2 - Electrical Trip (Alarm/Off Load Generator
Followed By Shutdown After Cooling)
3 - Shutdown (Alarm And Shutdown)
Rv.pow.act.delay time Reverse Power Action Delay Time 0 99 2 Sec

GEN WORKING CALENDAR (Generator->Working calendar) Min Max Default Unit

Disable/enable select Working Calendar Disable or Enable DISBL/ENABL DISBL
Start time on monday Working Calendar Work Start Time on Monday 0.00 23.59 0.00 H.Min
Stop time on monday Working Calendar Work Stop Time on Monday 0.00 23.59 23.59 H.Min
Start time on tues. Working Calendar Work Start Time on Tuesday 0.00 23.59 0.00 H.Min
Stop time on tuesday Working Calendar Work Stop Time on Tuesday 0.00 23.59 23.59 H.Min
Start time on wednes. Working Calendar Work Start Time on Wednesday 0.00 23.59 0.00 H.Min
Stop time on wednes. Working Calendar Work Stop Time on Wednesday 0.00 23.59 23.59 H.Min
Start time on thurs. Working Calendar Work Start Time on Thursday 0.00 23.59 0.00 H.Min
Stop time on thursday Working Calendar Work Stop Time on Thursday 0.00 23.59 23.59 H.Min
Start time on friday Working Calendar Work Start Time on Friday 0.00 23.59 0.00 H.Min
Stop time on friday Working Calendar Work Stop Time on Friday 0.00 23.59 23.59 H.Min
Start time on satur. Working Calendar Work Start Time on Saturday 0.00 23.59 0.00 H.Min
Stop time on saturday Working Calendar Work Stop Time on Saturday 0.00 23.59 23.59 H.Min
Start time on sunday Working Calendar Work Start Time on Sunday 0.00 23.59 0.00 H.Min
Stop time on sunday Working Calendar Work Stop Time on Sunday 0.00 23.59 23.59 H.Min

GENERATOR GENERAL (Generator->General) Min Max Default Unit

Sens.option gen.freq Sensing Options Generator Frq En/Dis ENABL/DISBL ENABL
Sens.opt.pickup&flywh Sensing Opt Pickup En/Dis & Flywheel 0(dis) 1000 DISBL
All warning are latch All Warnings Are Latched En/Dis ENABL/DISBL DISBL

10
4.2.4 Engine

ENGINE START OPTIONS (Engine->Starting options) Min Max Default Unit

Horn prior start Audible Alarm Prior To Starting En/Dis ENABL/DISBL DISBL
No. of crank attemp Number Of Start Attempts 1 10 3
Cranking time Cranking Time 1 99 5 Sec
Crank rest time Crank Rest Time 5 99 10 Sec
Pickup fail dely Pickup Sensor Fail Delay 0.1 10.0 1.0 Sec

ENG. CRANK DISCONNECT (Engine->Crank disconnect) Min Max Default Unit

Generator frequency Crank Disconnect On Gen. Frequency 10.0 75.0 30.0 Hz
Engine speed Crank Disconnect On Engine RPM 100 6000 500 RPM
Generator volt Crank Disconnect On Gen. Voltage 60 (dis) 600 300 VV
Charge alt. volt Crank Disconnect On Charge Alt. Voltage 6.0 (dis) 30.0 dis VZ
Oil pres. enab./dis. Crank Disconnect On Oil Pressure En/Dis ENABL/DISBL DISBL
Oil pressure value Crank Disconnect On Oil Pressure Value 1.0 30.0 1.0 BAR
Check oil befor.start Check Oil Pressure Before Start ENABL/DISBL ENABL

ENGINE SPEED SETS (Engine->Speed settings) Min Max Default Unit

Nominal speed Nominal Speed 500 5000 1500 RPM
Under speed shutdown Engine Under Speed Shutdown 500(dis) 5000 dis RPM
Under speed prealarm Engine Under Speed Prealarm 500(dis) 5000 dis RPM
Under speed reset Engine Under Speed Prealarm Reset 500 5000 500 RPM
Over speed shutdown Engine Over Speed Shutdown 500(dis) 5000 dis RPM
Over speed prealarm Engine Over Speed Prealarm 500(dis) 5000 dis RPM
Over speed reset Engine Over Speed Prealarm Reset 500 5000 500 RPM
Shutdown delay time Engine Speed Shutdown Delay Time 0.0 10.0 1.0 Sec

ENGINE PLANT BATTERY (Engine->Plant battery) Min Max Default Unit

Under volt shutdown Battery Undervolts Shutdown 6.0(dis) 30.0 dis VZ
Under volt warning Battery Undervolts Warning 6.0(dis) 30.0 10.0 VZ
Under volt reset Battery Undervolts Warning Reset 6.0 30.0 10.5 VZ
Under volt delay Battery Undervolts Volts Delay 0.0 9.9 1.0 Sec
Over volt shutdown Battery Overvolts Shutdown 6.0(dis) 30.0 dis VZ
Over volt warning Battery Overvolts Warning 6.0(dis) 30.0 30.0 VZ
Over volt reset Battery Overvolts Warning Reset 6.0 30.0 29.5 VZ
Over volt delay Battery Overvolts Delay 0.0 9.9 1.0 Sec
Alt. chg. warning Charge Alternator Warning 6.0(dis) 30.0 dis VZ

11
CANBUS ECU (Engine->CanBus ECU) Min Max Default Unit
Baud rate Baud Rate: 0 7 4 kBaud
0 - 20
1 - 50
2 - 100
3 - 125
4 - 250
5 - 500
6 - 800
7 - 1.000
J1939 ECU type J1939 ECU Type Selection: 0(dis) 13 0
0 - Disable
1 - Standard
2 - Volvo EMS1
3 - Volvo EMS2
4 - Volvo EMS2b
5 - Volvo EDC3
6 - Volvo EDC4
7 - Deutz EMR2
8 - Deutz EMR3
9 - Perkins 1300
10 - Perkins ADEM3
11 - Perkins ADEM4
12 - Scania S6
13 - MAN MFR
Device address Device Address 0 255 17
SPN version SPN version 1 3 1
ECU remote control ECU Remote Control via J1939 ENABL/DISBL ENABL
Speed control enable Speed Control via J1939 ENABL/DISBL ENABL
Oil pres cont. enab Oil Pressure Control via J1939 ENABL/DISBL DISBL
Temp. control enable Coolant Temperature Control via J1939 ENABL/DISBL DISBL
Speed set point Speed Set Point Selection 1500 / 1800 1500 RPM
Speed correction Speed Correction Value 0 100 50 %

Note: dis = disable

12
CANBUS ERROR SET (Engine->CanBus error set) Min Max Default Unit
CAN fault actions Can Fault Actions:
0- Disable
1- Warning Non-Latching
2- Warning (Alarm Only, No Shutdown)
3- Electrical Trip (Alarm/Off Load Generator
Followed By Shutdown After Cooling)
4- Shutdown (Alarm And Shutdown) 0(dis) 4 0

CAN fault activation Can Fault Activation: 0 2 0

0- Active From Starting
1- Active From Safety On
2- Always Active

CAN fault delay Can Fault Delay 2 250 10 Sec

Amber warn.actions J1939 Amber Warning Lamp Actions:
0- Disable
1- Warning Non-Latching
2- Warning (Alarm Only, No Shutdown)
3- Electrical Trip (Alarm/Off Load Generator
Followed By Shutdown After Cooling)
4- Shutdown (Alarm And Shutdown) 0(dis) 4 0

Amber warn.activation J1939 Amber Warning Lamp Activation: 0 2 2

0- Active From Starting
1- Active From Safety On
2- Always Active

Amber warn.delay J1939 Amber Warning Lamp Delay 0 250 2 Sec

Red stop actions J1939 Red Stop Lamp Actions:
0- Disable
1- Warning Non-Latching
2- Warning (Alarm Only, No Shutdown)
3- Electrical Trip (Alarm/Off Load Generator
Followed By Shutdown After Cooling)
4- Shutdown (Alarm And Shutdown) 0(dis) 4 0

Red stop activation J1939 Red Stop Lamp Activation: 0 2 2

0- Active From Starting
1- Active From Safety On
2- Always Active

Red stop delay J1939 Red Stop Lamp Delay 0 250 2 Sec

Note: dis = disable

13
ENGINE MAINTENANCE (Engine->Maintenance) Min Max Unit
Default
Running hour interval Running Hours Interval 0(dis) 9999 5000 Hour
Maint. date interval Maintenance Date Interval 0(dis) 12 6 Month
Eng. stop when maint Force Engine Shutdown When Maintenance Is Due ENABL/DISBL DISBL
Eng. running hour(lsb) Engine Running Hour (Lsb) 0 255 0
Eng. running hour Engine Running Hour 0 255 0
Eng. running hour(msb) Engine Running Hour(Msb) 0 14 0
Maintenance okay Maintenance Okay YES/NO NO

LOAD TEST (Engine->Load test) Min Max Default Unit

Disable/enable select Disable, No Load or On Load Selection 0-DISABLE 1-NO LOAD
1-NO LOAD
2-ON LOAD

EXERCISE (Engine->Exercise) Min Max Default Unit

Disable/enable select Exercise Disable or Enable DISBL/ENABL DISBL
Start time1 on monday Exercise Start Time 1 on Monday 0.00 23.59 0.00 H.Min
Stop time1 on monday Exercise Stop Time 1 on Monday 0.00 23.59 0.00 H.Min
Start time2 on monday Exercise Start Time 2 on Monday 0.00 23.59 0.00 H.Min
Stop time2 on monday Exercise Stop Time 2 on Monday 0.00 23.59 0.00 H.Min
Start time3 on monday Exercise Start Time 3 on Monday 0.00 23.59 0.00 H.Min
Stop time3 on monday Exercise Stop Time 3 on Monday 0.00 23.59 0.00 H.Min
Start time4 on monday Exercise Start Time 4 on Monday 0.00 23.59 0.00 H.Min
Stop time4 on monday Exercise Stop Time 4 on Monday 0.00 23.59 0.00 H.Min
Start time1 on tues. Exercise Start Time 1 on Tuesday 0.00 23.59 0.00 H.Min
Stop time1 on tuesday Exercise Stop Time 1 on Tuesday 0.00 23.59 0.00 H.Min
Start time2 on tues. Exercise Start Time 2 on Tuesday 0.00 23.59 0.00 H.Min
Stop time2 on Tuesday Exercise Stop Time 2 on Tuesday 0.00 23.59 0.00 H.Min
Start time3 on tues. Exercise Start Time 3 on Tuesday 0.00 23.59 0.00 H.Min
Stop time3 on tuesday Exercise Stop Time 3 on Tuesday 0.00 23.59 0.00 H.Min
Start time4 on tues. Exercise Start Time 4 on Tuesday 0.00 23.59 0.00 H.Min
Stop time4 on tuesday Exercise Stop Time 4 on Tuesday 0.00 23.59 0.00 H.Min
Start time1 on wednes. Exercise Start Time 1 on Wednesday 0.00 23.59 0.00 H.Min
Stop time1 on wednes. Exercise Stop Time 1 on Wednesday 0.00 23.59 0.00 H.Min
Start time2 on wednes. Exercise Start Time 2 on Wednesday 0.00 23.59 0.00 H.Min
Stop time2 on wednes. Exercise Stop Time 2 on Wednesday 0.00 23.59 0.00 H.Min
Start time3 on wednes. Exercise Start Time 3 on Wednesday 0.00 23.59 0.00 H.Min
Stop time3 on wednes. Exercise Stop Time 3 on Wednesday 0.00 23.59 0.00 H.Min
Start time4 on wednes. Exercise Start Time 4 on Wednesday 0.00 23.59 0.00 H.Min
Stop time4 on wednes. Exercise Stop Time 4 on Wednesday 0.00 23.59 0.00 H.Min
Start time1 on thurs. Exercise Start Time 1 on Thursday 0.00 23.59 0.00 H.Min
Stop time1 on thurs. Exercise Stop Time 1 on Thursday 0.00 23.59 0.00 H.Min
Start time2 on thurs. Exercise Start Time 2 on Thursday 0.00 23.59 0.00 H.Min
Stop time2 on thurs. Exercise Stop Time 2 on Thursday 0.00 23.59 0.00 H.Min
Start time3 on thurs. Exercise Start Time 3 on Thursday 0.00 23.59 0.00 H.Min
Stop time3 on thurs. Exercise Stop Time 3 on Thursday 0.00 23.59 0.00 H.Min
Start time4 on thurs. Exercise Start Time 4 on Thursday 0.00 23.59 0.00 H.Min
Stop time4 on thurs. Exercise Stop Time 4 on Thursday 0.00 23.59 0.00 H.Min

Note: dis = disable

14
Start time1 on friday Exercise Start Time 1 on Friday 0.00 23.59 0.00 H.Min
Stop time1 on friday Exercise Stop Time 1 on Friday 0.00 23.59 0.00 H.Min
Start time2 on friday Exercise Start Time 2 on Friday 0.00 23.59 0.00 H.Min
Stop time2 on friday Exercise Stop Time 2 on Friday 0.00 23.59 0.00 H.Min
Start time3 on friday Exercise Start Time 3 on Friday 0.00 23.59 0.00 H.Min
Stop time3 on friday Exercise Stop Time 3 on Friday 0.00 23.59 0.00 H.Min
Start time4 on friday Exercise Start Time 4 on Friday 0.00 23.59 0.00 H.Min
Stop time4 on friday Exercise Stop Time 4 on Friday 0.00 23.59 0.00 H.Min
Start time1 on satur. Exercise Start Time 1 on Saturday 0.00 23.59 0.00 H.Min
Stop time1 on satur. Exercise Stop Time 1 on Saturday 0.00 23.59 0.00 H.Min
Start time2 on satur. Exercise Start Time 2 on Saturday 0.00 23.59 0.00 H.Min
Stop time2 on satur. Exercise Stop Time 2 on Saturday 0.00 23.59 0.00 H.Min
Start time3 on satur. Exercise Start Time 3 on Saturday 0.00 23.59 0.00 H.Min
Stop time3 on satur. Exercise Stop Time 3 on Saturday 0.00 23.59 0.00 H.Min
Start time4 on satur. Exercise Start Time 4 on Saturday 0.00 23.59 0.00 H.Min
Stop time4 on satur. Exercise Stop Time 4 on Saturday 0.00 23.59 0.00 H.Min
Start time1 on sunday Exercise Start Time 1 on Sunday 0.00 23.59 0.00 H.Min
Stop time1 on sunday Exercise Stop Time 1 on Sunday 0.00 23.59 0.00 H.Min
Start time2 on sunday Exercise Start Time 2 on Sunday 0.00 23.59 0.00 H.Min
Stop time2 on sunday Exercise Stop Time 2 on Sunday 0.00 23.59 0.00 H.Min
Start time3 on sunday Exercise Start Time 3 on Sunday 0.00 23.59 0.00 H.Min
Stop time3 on sunday Exercise Stop Time 3 on Sunday 0.00 23.59 0.00 H.Min
Start time4 on sunday Exercise Start Time 4 on Sunday 0.00 23.59 0.00 H.Min
Stop time4 on sunday Exercise Stop Time 4 on Sunday 0.00 23.59 0.00 H.Min

ENGINE GENERAL (Engine->General) Min Max Default Unit

Fuel selection Engine Fuel Selection 0-GAS 1-DIESEL
1-DIESEL
2-GASOLINE
Stop solenoid time Stop Solenoid Time 5 99 20 Sec
Ignition delay Ignition Delay 1 99 5 Sec
Gas valve delay Gas Valve Delay 1 99 5 Sec
Min. of ignition speed Minimum Ignition Speed 10 1500 200 RPM
Choke time Choke Time 0.0 30.0 0.8 Sec

Note: dis = disable

15
4.2.5 Inputs

SENDER INPUTS (Inputs->Sender inputs) Min Max Default Unit

Oil pressure unit Oil Pressure Unit BAR/PSI/KPA BAR
Oil press. input type Oil Pressure Input Type 0 - Not Used (Disable) 0 (dis)
1 - Digital NC
2 - Digital NO
3 - VDO 5 BAR
4 - VDO 7 BAR
5 - VDO 10 BAR
6 - DATCON 5 BAR
7 - DATCON 7 BAR
8 - MURPHY 7 BAR
9 - User Configured
Oil pressure prealarm Oil Pressure Pre-Alarm 0.0 (dis) 30.0 1.2 BAR
Oil pressure reset Oil Pressure Pre-Alarm Reset 0.0 30.0 1.4 BAR
Oil pressure shutdown Oil Pressure Shutdown 0.0 30.0 1.0 BAR
Temperature unit Coolant Temperature Unit C/F C
Temp. input type Coolant Temperature Input Type 0 - Not Used (Disable) 0 (dis)
1 - Digital NC
2 - Digital NO
3 - VDO 120 C
4 - VDO 150 C
5 - DATCON
6 - MURPHY
7 - PT100
8 - User Configured
Temp. sensor break Temperature Sensor Break DISBL/ENABL DISBL
High temp. prealarm High Temperature Pre-Alarm 0 (dis) 300 90 C
High temp. reset High Temp. Pre-Alarm Reset 0 300 88 C
High temp. shutdown High Temperature Shutdown 0 300 95 C
Low temp. warning Low Temperature Warning 0 (dis) 70 0 (dis) C
Heater control ON Coolant Heater Control On 0 (dis) 300 0 (dis) C
Heater control OFF Coolant Heater Control Off 0 300 45 C
Water pump on time Water Pump On Time 0 9999 5 Sec
Water pump off time Water Pump Off Time 0 9999 5 Sec
Conf. AI1 unit Configurable Analog Input-1 Unit BAR/PSI/KPA/C/F/%/Lt %
Conf. AI1 type Configurable Analog Input-1 Type 0 - Not Used (Disable) 0 (dis)
1 - Digital NC
2 - Digital NO
3 - VDO OHM (10-180)
4 - VDO TUBE (90-0)
5 - US OHM (240-33)
6 - EMS OHM (0-190)
7 - FORD (73-10)
8 - User Configured
Conf. AI1 low prealrm Configurable Analog Input-1 0 (dis) 3000 0 (dis) %
Low Pre-Alarm
Conf. AI1 low reset Configurable Analog Input-1 0 3000 60 %
Low Reset
Conf. AI1 low shutdwn Configurable Analog Input-1 0 (dis) 3000 0 (dis) %
Low Shutdown
Conf. AI1 high prealr Configurable Analog Input-1 0 (dis) 3000 0 (dis) %
High Pre-Alarm
Conf. AI1 high reset Configurable Analog Input-1 0 3000 90 %
High Reset

16
Conf. AI1 high shutd. Configurable Analog Input-1 0 (dis) 3000 0 (dis) %
High Shutdown
Conf. AI1 control ON Configurable Analog Input-1 0 (dis) 3000 0 (dis) %
control ON
Conf. AI1 control OFF Configurable Analog Input-1 0 3000 75 %
control OFF
Conf. AI2 unit Configurable Analog Input-2 Unit BAR/PSI/KPA/C/F/%/Lt C
Conf. AI2 type Configurable Analog Input-2 Type 0 - Not Used (Disable) 0 (dis)
1 - Digital NC
2 - Digital NO
3 - VDO 120 C
4 - VDO 150 C
5 - DATCON
6 - MURPHY
7 - PT100
8 - User Configured
Conf. AI2 low prealrm Configurable Analog Input-2 0 (dis) 300 0 (dis) C
Low Pre-Alarm
Conf. AI2 low reset Configurable Analog Input-2 0 300 60 C
Low Reset
Conf. AI2 low shutdwn Configurable Analog Input-2 0 (dis) 300 0 (dis) C
Low Shutdown
Conf. AI2 high prealr Configurable Analog Input-2 0 (dis) 300 0 (dis) C
High Pre-Alarm
Conf. AI2 high reset Configurable Analog Input-2 0 300 90 C
High Reset
Conf. AI2 high shutd. Configurable Analog Input-2 0 (dis) 300 0 (dis) C
High Shutdown
Configurable Analog Input-2 0 (dis) 300 0 (dis) C
Conf. AI2 control ON
control ON
Configurable Analog Input-2 0 300 75 C
Conf. AI2 control OFF
control OFF

Note: dis = disable

17
SENDER LINEARISATION (Inputs->Sender linearisation) Min Max Default Unit
Oil pressure sender 1 Oil Pressure Sender Point-1 0 1300 15 R
Oil pressure 1 Oil Pressure Point-1 0.0 30.0 0.0 BAR
Oil pressure sender 2 Oil Pressure Sender Point-2 0 1300 31 R
Oil pressure 2 Oil Pressure Point-2 0.0 30.0 1.0 BAR
Oil pressure sender 3 Oil Pressure Sender Point-3 0 1300 49 R
Oil pressure 3 Oil Pressure Point-3 0.0 30.0 2.0 BAR
Oil pressure sender 4 Oil Pressure Sender Point-4 0 1300 66 R
Oil pressure 4 Oil Pressure Point-4 0.0 30.0 3.0 BAR
Oil pressure sender 5 Oil Pressure Sender Point-5 0 1300 85 R
Oil pressure 5 Oil Pressure Point-5 0.0 30.0 4.0 BAR
Oil pressure sender 6 Oil Pressure Sender Point-6 0 1300 101 R
Oil pressure 6 Oil Pressure Point-6 0.0 30.0 5.0 BAR
Oil pressure sender 7 Oil Pressure Sender Point-7 0 1300 117 R
Oil pressure 7 Oil Pressure Point-7 0.0 30.0 6.0 BAR
Oil pressure sender 8 Oil Pressure Sender Point-8 0 1300 132 R
Oil pressure 8 Oil Pressure Point-8 0.0 30.0 7.0 BAR
Oil pressure sender 9 Oil Pressure Sender Point-9 0 1300 149 R
Oil pressure 9 Oil Pressure Point-9 0.0 30.0 8.0 BAR
Oil pressure sender 10 Oil Pressure Sender Point-10 0 1300 178 R
Oil pressure 10 Oil Pressure Point-10 0.0 30.0 10.0 BAR
Temperature sender 1 Temperature Sender Point-1 0 1300 579 R
Temperature 1 Temperature Point-1 0 300 28 C
Temperature sender 2 Temperature Sender Point-2 0 1300 404 R
Temperature 2 Temperature Point-2 0 300 35 C
Temperature sender 3 Temperature Sender Point-3 0 1300 342 R
Temperature 3 Temperature Point-3 0 300 40 C
Temperature sender 4 Temperature Sender Point-4 0 1300 250 R
Temperature 4 Temperature Point-4 0 300 50 C
Temperature sender 5 Temperature Sender Point-5 0 1300 179 R
Temperature 5 Temperature Point-5 0 300 60 C
Temperature sender 6 Temperature Sender Point-6 0 1300 136 R
Temperature 6 Temperature Point-6 0 300 70 C
Temperature sender 7 Temperature Sender Point-7 0 1300 103 R
Temperature 7 Temperature Point-7 0 300 80 C
Temperature sender 8 Temperature Sender Point-8 0 1300 77 R
Temperature 8 Temperature Point-8 0 300 90 C
Temperature sender 9 Temperature Sender Point-9 0 1300 67 R
Temperature 9 Temperature Point-9 0 300 95 C
Temperature sender 10 Temperature Sender Point-10 0 1300 63 R
Temperature 10 Temperature Point-10 0 300 98 C
Conf. AI1 sender 1 Configurable Analog Input-1 Sender Point-1 0 1300 10 R
Conf. AI1 value 1 Configurable Analog Input-1 Point-1 0 3000 0 %
Conf. AI1 sender 2 Configurable Analog Input-1 Sender Point-2 0 1300 30 R
Conf. AI1 value 2 Configurable Analog Input-1 Point-2 0 3000 11 %
Conf. AI1 sender 3 Configurable Analog Input-1 Sender Point-3 0 1300 50 R
Conf. AI1 value 3 Configurable Analog Input-1 Point-3 0 3000 22 %
Conf. AI1 sender 4 Configurable Analog Input-1 Sender Point-4 0 1300 70 R
Conf. AI1 value 4 Configurable Analog Input-1 Point-4 0 3000 33 %
Conf. AI1 sender 5 Configurable Analog Input-1 Sender Point-5 0 1300 90 R
Conf. AI1 value 5 Configurable Analog Input-1 Point-5 0 3000 44 %

18
Conf. AI1 sender 6 Configurable Analog Input-1 Sender Point-6 0 1300 110 R
Conf. AI1 value 6 Configurable Analog Input-1 Point-6 0 3000 55 %
Conf. AI1 sender 7 Configurable Analog Input-1 Sender Point-7 0 1300 130 R
Conf. AI1 value 7 Configurable Analog Input-1 Point-7 0 3000 66 %
Conf. AI1 sender 8 Configurable Analog Input-1 Sender Point-8 0 1300 150 R
Conf. AI1 value 8 Configurable Analog Input-1 Point-8 0 3000 77 %
Conf. AI1 sender 9 Configurable Analog Input-1 Sender Point-9 0 1300 170 R
Conf. AI1 value 9 Configurable Analog Input-1 Point-9 0 3000 88 %
Conf. AI1 sender 10 Configurable Analog Input-1 Sender Point-10 0 1300 190 R
Conf. AI1 value 10 Configurable Analog Input-1 Point-10 0 3000 100 %
Conf. AI2 sender 1 Configurable Analog Input-2 Sender Point-1 0 1300 579 R
Conf. AI2 value 1 Configurable Analog Input-2 Point-1 0 300 28 C
Conf. AI2 sender 2 Configurable Analog Input-2 Sender Point-2 0 1300 404 R
Conf. AI2 value 2 Configurable Analog Input-2 Point-2 0 300 35 C
Conf. AI2 sender 3 Configurable Analog Input-2 Sender Point-3 0 1300 342 R
Conf. AI2 value 3 Configurable Analog Input-2 Point-3 0 300 40 C
Conf. AI2 sender 4 Configurable Analog Input-2 Sender Point-4 0 1300 250 R
Conf. AI2 value 4 Configurable Analog Input-2 Point-4 0 300 50 C
Conf. AI2 sender 5 Configurable Analog Input-2 Sender Point-5 0 1300 179 R
Conf. AI2 value 5 Configurable Analog Input-2 Point-5 0 300 60 C
Conf. AI2 sender 6 Configurable Analog Input-2 Sender Point-6 0 1300 136 R
Conf. AI2 value 6 Configurable Analog Input-2 Point-6 0 300 70 C
Conf. AI2 sender 7 Configurable Analog Input-2 Sender Point-7 0 1300 103 R
Conf. AI2 value 7 Configurable Analog Input-2 Point-7 0 300 80 C
Conf. AI2 sender 8 Configurable Analog Input-2 Sender Point-8 0 1300 77 R
Conf. AI2 value 8 Configurable Analog Input-2 Point-8 0 300 90 C
Conf. AI2 sender 9 Configurable Analog Input-2 Sender Point-9 0 1300 67 R
Conf. AI2 value 9 Configurable Analog Input-2 Point-9 0 300 95 C
Conf. AI2 sender 10 Configurable Analog Input-2 Sender Point-10 0 1300 63 R
Conf. AI2 value 10 Configurable Analog Input-2 Point-10 0 300 98 C

19
CONF. INPUT-X (Inputs->Conf. input-x) Min Max Default Unit
Dis,user conf.or list 0- Disable 0(dis) 2 in2,in1=2
3=1
1- User Configured in4, 5=2
2- Select From List in6=1
Polarity 0- Normally Open (Close To Activate) 0 1 in1, 3=1
in2, 4=0
1- Normally Close (Open To Activate) in5, 6=0
Indication If User Configured 0 4 in1=0
in2=0
0- Status in3=4
1- Warning Non-Latching in4=0
2- Warning Latching in5=0
3- Electrical Trip in6=0
4- Shutdown
Activation If User Configured 0 2 in1, 2=2
in3, 4=2
0- Active From Starting in5, 6=2
1- Active From Safety On
2- Always Active
Select from list If Select From List 0 in1=26 in1=25
0-Remote Start On Load in2=24 in2=3
in3=24 in3=4
1-Remote Start Off Load in4=26 in4=25
2-Auxiliary Mains Fail in5=25 in5=25
3-Simulate Lamp Test Button in6=24 in6=7
4-Simulate Horn Reset Button
5-Simulate Alarm Reset Button
6-Simulate Auto Button
7-Simulate Test Button
8-Simulate Manual Button
9-Simulate Start Button
10-Simulate Stop Button
11-Generator Closed Auxiliary
12-Generator Load Inhibit
13-Mains Closed Auxiliary
14-Mains Load Inhibit
15-Auto Restore Inhibit
16-Auto Start Inhibit
17-Panel Lock
18-Scheduled Runs(Exercise) Inhibited
19-Priority Select
20-Transfer To Generator/Open Mains
21-Transfer To Mains/Open Generator
22-Remote Inhibit
23-Being Found Alive
24-Generator is loaded in stop mode
25 - Emergency Stop (for only input-1)
25 - Low Oil Pressure (for only input-4)
25 - High Temperature (for only input-5)
26 - Low Oil Level (for only input-4)
26 - Emergency Stop No-Latching (for only input-1)
Active delay Input active delay 0 250 in1=0 Sec
in2, 3=5
in4, 5=0
in6=5

Note-1 : x = 1(input-1), 2(input-2), 3(input-3), 4(input-4), 5(input-5), or 6(input-6)

Note-2 : 25 - Emergency Stop (for only input-1)
25 - Low Oil Pressure (for only input-4)
25 - High Temperature (for only input-5)
26 - Low Oil Level (for only input-4)
26 - Emergency Stop No-Latching (for only input-1)
Note-3 : dis = disable

20
CONF. INPUT-7 (Inputs->Conf. input-7) Min Max Default Unit
Input type 0- Disable 0(dis) 3 3
1- User Configured (Digital)
2- Select From List (Digital)
3- Cabin Temperature (Anolog)
Polarity If Input Type is Digital 0 1 0
0- Normally Open (Close To Activate)
1- Normally Close (Open To Activate)
Indication If Input Type is User Configured 0 4 0
0- Status
1- Warning Non-Latching
2- Warning Latching
3- Electrical Trip
4- Shutdown
Activation If Input Type is User Configured 0 2 2
0- Active From Starting
1- Active From Safety On
2- Always Active
Select from list If Input Type is Select From List 0 24 8
0-Remote Start On Load
1-Remote Start Off Load
2-Auxiliary Mains Fail
3-Simulate Lamp Test Button
4-Simulate Horn Reset Button
5-Simulate Alarm Reset Button
6-Simulate Auto Button
7-Simulate Test Button
8-Simulate Manual Button
9-Simulate Start Button
10-Simulate Stop Button
11-Generator Closed Auxiliary
12-Generator Load Inhibit
13-Mains Closed Auxiliary
14-Mains Load Inhibit
15-Auto Restore Inhibit
16-Auto Start Inhibit
17-Panel Lock
18-Scheduled Runs(Exercise) Inhibited
19-Priority Select
20-Transfer To Generator/Open Mains
21-Transfer To Mains/Open Generator
22-Remote Inhibit
23-Being Found Alive
24-Generator is loaded in stop mode

Active delay Input active delay (If Input Type is Digital) 0 250 5 Sec
Cabin temp.low prealr Cabin temperature low prealarm -50(dis) 100 dis C
Cabin temp.low reset Cabin temperature low prealarm reset -50 100 0 C
Cabin temp.low shutd. Cabin temperature low shutdown -50(dis) 100 dis C
Cabin temp.high preal Cabin temperature high prealarm reset -50(dis) 100 dis C
Cabin temp.high reset Cabin temperature high prealarm -50 100 0 C
Cabin temp.high shutd Cabin temperature high shutdown -50(dis) 100 dis C

Note: dis = disable

21
CONF. EXP. INPUT-X (Inputs->Conf. exp. input-x) Min Max Default Unit
Dis,user conf.or list 0- Disable 0(dis) 2 1
1- User Configured
2- Select From List
Hardware type 0-> -Ve (Switched To Battery -) 0 1 0
1-> +Ve (Switched To Battery +)
Polarity 0- Normally Open (Close To Activate) 0 1 0
1- Normally Close (Open To Activate)
Indication If User Configured 0 4 0
0- Status
1- Warning Non-Latching
2- Warning Latching
3- Electrical Trip
4- Shutdown
Activation If User Configured 0 2 2
0- Active From Starting
1- Active From Safety On
2- Always Active
Select from list If Select From List 2 21 2
2-Auxiliary Mains Fail
3-Simulate Lamp Test Button
4-Simulate Horn Reset Button
5-Simulate Alarm Reset Button
6-Simulate Auto Button
7-Simulate Test Button
8-Simulate Manual Button
9-Simulate Start Button
10-Simulate Stop Button
11-Generator Closed Auxiliary
12-Generator Load Inhibit
13-Mains Closed Auxiliary
14-Mains Load Inhibit
15-Auto Restore Inhibit
16-Auto Start Inhibit
17-Panel Lock
18-Scheduled Runs Inhibited
19-Priority Select
20-Transfer To Generator/Open Mains
21-Transfer To Mains/Open Generator
Active delay Input active delay 0 250 5 Sec

Note-1 : x = 1(exp. input-1), 2(exp. input-2), 3(exp. input-3), 4(exp. input-4), 5(exp. input-5), 6(exp.
input-6), 7(exp. input-7) or 8(exp. input-8)
Note-2 : dis = disable

22
4.2.6 Outputs
CONF. OUTPUT-1 (Outputs->Conf. output-1) Min Max Default Unit
Polarity 0- Normally Open (Close To Activate) 0 1 0
1- Normally Close (Open To Activate)
0-NOT USED
Function 1-AIR FLAP CONTROL 0 131 43
2-ALARM RESET
3-AUDIBLE ALARM
4-AUTO START INHIBIT
5-AUXILIARY MAINS FAILURE
6-BATTERY HIGH VOLTAGE
7-BATTERY LOW VOLTAGE
8-CALLING FOR SCHEDULED RUN(EXERCISE)
9-CAN ECU POWER
10-CAN ECU STOP
11-CHARGE ALTERNATOR FAILURE
12-COMMON ALARM
13-COMMON ELECTRICAL TRIP ALARM
14-COMMON SHUTDOWN ALARM
15-COMMON WARNING ALARM
16-COOLING FAN AFTER START
17-COOLING FAN AFTER STOP
18-COOLANT TEMPERATURE HIGH PRE-ALARM
19-COOLANT TEMPERATURE HIGH SHUTDOWN
20-COOLING DOWN TIMER IN PROGRESS
21-CRANK RELAY ENERGISED
22-DELAYED ALARMS ACTIVE
23-DIGITAL INPUT1 ALARM
24-DIGITAL INPUT2 ALARM
25-DIGITAL INPUT3 ALARM
26-DIGITAL INPUT4 ALARM
27-DIGITAL INPUT5 ALARM
28-DIGITAL INPUT6 ALARM
29-DIGITAL INPUT7 ALARM
30-EXPANSION INPUT1 ALARM
31-EXPANSION INPUT2 ALARM
32-EXPANSION INPUT3 ALARM
33-EXPANSION INPUT4 ALARM
34-EXPANSION INPUT5 ALARM
35-EXPANSION INPUT6 ALARM
36-EXPANSION INPUT7 ALARM
37-EXPANSION INPUT8 ALARM
38-EARTH FAULT
39-EMERGENCY STOP
40-FAIL TO START ALARM
41-FAIL TO STOP ALARM
42-CONF. AI1 CONTROL
43-FUEL RELAY ENERGISED
44-GAS ENGINE IGNITION OUTPUT
45-GENERATOR AT REST
46-GENERATOR AVAILABLE
47-GENERATOR CLOSED AUXILIARY
48-GENERATOR FAILED TO CLOSE
49-GENERATOR FAILED TO OPEN
50-GENERATOR HIGH FREQUENCY PRE-ALARM
51-GENERATOR HIGH FREQUENCY SHUTDOWN
52-GENERATOR HIGH VOLTAGE PRE-ALARM
53-GENERATOR HIGH VOLTAGE SHUTDOWN
54-GENERATOR LOAD INHIBIT
55-GENERATOR LOW FREQUENCY PRE-ALARM
56-GENERATOR LOW FREQUENCY SHUTDOWN
57-GENERATOR LOW VOLTAGE PRE-ALARM
58-GENERATOR LOW VOLTAGE SHUTDOWN
59-GENERATOR STOPPING
60-GENERATOR OPEN BREAKER
61-HORN OUTPUT LATCHED
62-HORN OUTPUT PULSED
63-LAMP TEST
64-CONF. AI2 CONTROL
65-LOSS OF MAGNETIC PICK-UP SPEED SIGNAL
66-LOW TEMPERATURE
67-MAINTENANCE DUE ALARM
68-MAINS CLOSED AUXILIARY
69-MAINS FAILED TO CLOSE
70-MAINS FAILED TO OPEN
71-MAINS FAILURE
72-MAINS HIGH FREQUENCY
73-MAINS HIGH VOLTAGE
74-MAINS LOAD INHIBIT
75-MAINS LOW FREQUENCY
76-MAINS LOW VOLTAGE
77-MAINS OPEN BREAKER
78-NO LOADING COMMAND
79-OIL PRESSURE LOW PRE-ALARM
80-OIL PRESSURE LOW SHUTDOWN
81-CONF.AI1.HIGH PREA
82-CONF.AI1.HIGH SHUT
83-OVER CURRENT PRE-ALARM
84-OVER CURRENT
85-OVER POWER PRE-ALARM
86-OVER POWER SHUTDOWN
87-OVERSPEED PRE-ALARM
88-OVERSPEED SHUTDOWN
89-PANEL LOCK
90-PRE-HEAT(during preheat timer)
91-PRE-HEAT(until end of cranking)
92-PRE-HEAT(until end of warming)
93-PRE-HEAT(until end safety on)
94-REMOTE START PRESENT
95-REMOTE STOP DELAY IN PROGRESS
96-SHORT CIRCUIT
97-SMOKE LIMITING
98-STARTING ALARM
99-STARTING ALARMS ARMED
100-STOP RELAY ENERGISED
101-SYSTEM IN AUTO MODE
102-SYSTEM IN MANUAL MODE
103-SYSTEM IN STOP MODE
104-SYSTEM IN TEST MODE
105-UNDER CURRENT PRE-ALARM
106-UNDER CURRENT
107-UNDER POWER PRE-ALARM
108-UNDER POWER SHUTDOWN
109-UNDERSPEED PRE-ALARM
110-UNDERSPEED SHUTDOWN
111-WAITING FOR GENERATOR
112-DUAL COMMUNICATION ERROR
113-LOAD SUPPLY FROM GENERATOR
114-LOAD SUPPLY FROM MAINS
115-CONFIGURABLE ANALOG INPUT 1 LOW PRE-ALARM
116-CONFIGURABLE ANALOG INPUT 1 LOW SHUTDOWN
117-CONFIGURABLE ANALOG INPUT 2 LOW PRE-ALARM
118-CONFIGURABLE ANALOG INPUT 2 LOW SHUTDOWN
119-CONFIGURABLE ANALOG INPUT 2 HIGH PRE-ALARM
120-CONFIGURABLE ANALOG INPUT 2 HIGH SHUTDOWN
121-CHOKE ACTIVE
122-REMOTE CONTROL ACTIVE
123-REVERSE POWER
124-CABIN TEMPERATURE LOW PRE-ALARM
125-CABIN TEMPERATURE LOW SHUTDOWN
126-CABIN TEMPERATURE HIGH PRE-ALARM
127-CABIN TEMPERATURE HIGH SHUTDOWN
128-HEATER CONTROL
129-REMOTE OUTPUT
130-UNBALANCE LOAD
131-WATER PUMP

23
CONF. OUTPUT-2 (Outputs->Conf. output-2) Min Max Default Unit
Polarity 0- Normally Open (Close To Activate) 0 1 0
1- Normally Close (Open To Activate)
Function The same as Configurable Output-1 options 0 131 21

CONF. OUTPUT-3 (Outputs->Conf. output-3) Min Max Default Unit

Polarity 0- Normally Open (Close To Activate) 0 1 0
1- Normally Close (Open To Activate)
Function The same as Configurable Output-1 options 0 131 62

CONF. OUTPUT-4 (Outputs->Conf. output-4) Min Max Default Unit

Polarity 0- Normally Open (Close To Activate) 0 1 0
1- Normally Close (Open To Activate)
Function The same as Configurable Output-1 options 0 131 9

CONF. OUTPUT-5 (Outputs->Conf. output-5) Min Max Default Unit

Polarity 0- Normally Open (Close To Activate) 0 1 0
1- Normally Close (Open To Activate)
Function The same as Configurable Output-1 options 0 131 10

CONF. OUTPUT-6 (Outputs->Conf. output-6) Min Max Default Unit

Polarity 0- Normally Open (Close To Activate) 0 1 0
1- Normally Close (Open To Activate)
Function The same as Configurable Output-1 options 0 131 12

CONF. EXP. OUTPUT-1 (Outputs->Conf. exp. output-1) Min Max Default Unit
Polarity 0- Normally Open (Close To Activate) 0 1 0
1- Normally Close (Open To Activate)
Function The same as Configurable Output-1 options 0 131 12

CONF. EXP. OUTPUT-2 (Outputs->Conf. exp. output-2) Min Max Default Unit
Polarity 0- Normally Open (Close To Activate) 0 1 0
1- Normally Close (Open To Activate)
Function The same as Configurable Output-1 options 0 131 12

CONF. EXP. OUTPUT-3 (Outputs->Conf. exp. output-3) Min Max Default Unit
Polarity 0- Normally Open (Close To Activate) 0 1 0
1- Normally Close (Open To Activate)
Function The same as Configurable Output-1 options 0 131 12

CONF. EXP. OUTPUT-4 (Outputs->Conf. exp. output-4) Min Max Default Unit
Polarity 0- Normally Open (Close To Activate) 0 1 0
1- Normally Close (Open To Activate)
Function The same as Configurable Output-1 options 0 131 12

CONF. EXP. OUTPUT-5 (Outputs->Conf. exp. output-5) Min Max Default Unit
Polarity 0- Normally Open (Close To Activate) 0 1 0
1- Normally Close (Open To Activate)
Function The same as Configurable Output-1 options 0 131 12

CONF. EXP. OUTPUT-6 (Outputs->Conf. exp. output-6) Min Max Default Unit
Polarity 0- Normally Open (Close To Activate) 0 1 0
1- Normally Close (Open To Activate)
Function The same as Configurable Output-1 options 0 131 12

24
CONF. EXP. OUTPUT-7 (Outputs->Conf. exp. output-7) Min Max Default Unit
Polarity 0- Normally Open (Close To Activate) 0 1 0
1- Normally Close (Open To Activate)
Function The same as Configurable Output-1 options 0 131 12

CONF. EXP. OUTPUT-8 (Outputs->Conf. exp. output-8) Min Max Default Unit
Polarity 0- Normally Open (Close To Activate) 0 1 0
1- Normally Close (Open To Activate)
Function The same as Configurable Output-1 options 0 131 12

4.2.7 Timers
START TIMERS (Timers->Start timers) Min Max Default Unit
Mains transient delay Mains Transient Delay 0.0 20.0 2.0 Sec
Mains fail start dely Mains Fail Start Delay 0 9999 0 Sec
Remote start delay Remote Start Delay 0 3600 4 Sec
Pre-heat Pre-Heat 0 250 3 Sec
Pre-heat bypass Pre-Heat Bypass 0 250 0 Min
Safety on delay Safety On Delay 0 99 5 Sec
Warming up time Warmup Time 0 250 3 Sec
Horn duration Horn Duration 0 (dis) 999 60 Sec
Chg. excitation time Charge Excitation Time 0 99(cont) 15 Sec
Cooling fan time Cooling Fan Time 0 250 180 Sec
Idle mode time Idle Mode Time (Smoke Limiting) 0 (dis) 3600 dis Sec
Idle mode time off Idle Mode Time Off (Smoke Limiting Off) 0 250 5 Sec

STOPPING TIMERS (Timers->Stopping timers) Min Max Default Unit

Mains return delay Mains Return Delay 0 3600 5 Sec
Remote stop delay Remote Stop Delay 0 250 4 Sec
Cooling time Cooling Time 0 (dis) 3600 60 Sec
Fail to stop delay Fail To Stop Time 15 99 30 Sec

4.2.8 Expansion Modules

IO (1-8) MODULE (Expansion modules->IO (1-8)) Min Max Default Unit
Disable/enable select Expansion I/O Module Selection ENABL/DISBL DISBL

DIAL-UP & ETHERNET (Expansion modules->Dial-up & Ethernet) Min Max Default Unit
Disable/enable select Expansion Dal-up&Ethernet Module Selection ENABL/DISBL ENABL
Call back selection Call Back Selection ENABL/DISBL DISBL

GSM MODULE (Expansion modules->GSM) Min Max Default Unit

Disable/enable select Expansion GSM Module Selection ENABL/DISBL ENABL
Call back selection Call Back Selection ENABL/DISBL DISBL
SMS SMS Feature Enable or Disable ENABL/DISBL DISBL

GPRS MODULE (Expansion modules->GPRS) Min Max Default Unit

Disable/enable select Expansion GPRS Module Selection 0-DISABLE 1-SERVER
1-SERVER
2-CLIENT
Call back selection Call Back Selection ENABL/DISBL DISBL
GPS GPS Feature Enable or Disable ENABL/DISBL DISBL

Note: dis = disable cont = continuous

25
DUAL SET MODULE (Expansion modules->Dual set) Min Max Default Unit
Disable/enable select Expansion Dual Set Module Selection ENABL/DISBL ENABL
Node ID Node Address 1 2 1
Working period Dual Working Period 0:00 9:59 1:00 H.Min
Early start time Early Start Time 0 250 15 Sec
Remote priority selct Remote Priority Selection: 0(dis) 2 dis
0- Disable, 1- Priority, 2- None Priority

WEB SERVER MODULE (Expansion modules->Web Server) Min Max Default Unit
Disable/enable select Web Server Module Selection ENABL/DISBL ENABL

GPRS WEB MODULE (Expansion modules->GPRS Web) Min Max Default Unit
Disable/enable select GPRS-Web Module Selection ENABL/DISBL ENABL

4.2.9 User Adjustment

MAINS VOLTAGE OFFSET (User adjustment->Mains voltage offset) Min Max Default Unit
Mains V1 offset Mains V1 Offset -20 20 0 VV
Mains V2 offset Mains V2 Offset -20 20 0 VV
Mains V3 offset Mains V3 Offset -20 20 0 VV

GEN. VOLTAGE OFFSET (User adjustment->Gen. voltage offset) Min Max Default Unit
Gen. V1 offset Generator V1 Offset -20 20 0 VV
Gen. V2 offset Generator V2 Offset -20 20 0 VV
Gen. V3 offset Generator V3 Offset -20 20 0 VV

CURRENT OFFSET (User adjustment->Current offset) Min Max Default Unit

Current I1 offset Current I1 Offset -20 20 0 AV
Current I2 offset Current I2 Offset -20 20 0 AV
Current I3 offset Current I3 Offset -20 20 0 AV
E/F. Current offset Earth current I3 Offset -20 20 0 AV

BATTERY&CHRG GEN.VOL (User adjustment->Battery&chrg gen.vol) Min Max Default Unit

Batt.volt offset Battery Voltage Offset -5.0 5.0 0 VZ
Gen.chg.volt offset Charge Generator Voltage Offset -5.0 5.0 0 VZ

SENDER INPUTS OFFSET (User adjustment->Sender inputs offset) Min Max Default Unit
Oil Pressure offset Oil Pressure Offset -2.0 2.0 0.0 BAR
Temperature offset Coolant Temperature Offset -20 20 0 C
Conf. AI1 offset Configurable Analog Input-1 Offset -200 200 0 %
Conf. AI2 offset Configurable Analog Input-2 Offset -20 20 0 C

Note: dis = disable

26
5. Specifications
Equipment use : Electrical control equipment for generating sets.
Housing & Mounting : 229 mm x 152 mm x 41 mm. (including connectors). Plastic
housing for panel mounting.
Panel Cut-Out : 182mm x 135mm.
Protection : IP65 at front panel.
Weight : Approximately 0,53 Kg.
Environmental rating : Standard, indoor at an altitude of less then 2000 meters
with non-condensing humidity.
Operating/Storage Temperature : -20C to +70C / -30C to +80C
Operating/Storage Humidity : 90 % max. (non-condensing)
Installation Over Volt. Category : II Appliances, portable equipment
Pollution Degree : II, Normal office or workplace, non conductive pollution
Mode of Operation : Continuous.
DC Battery Supply Voltage : 8 to 32 V Z. Max. operating current is 360 mA.
Cranking Dropouts : Battery voltage can be 0 VDC for max. 50 ms during
cranking (battery voltage should be at least nominal
voltage before cranking).
Battery Voltage Measurement : 8 to 32 V Z, accuracy: 1 % FS, resolution: 0,1 V
Mains Voltage Measurement : 3 to 300 VAC Ph-N, 5 to 99.9 Hz. Accuracy: 1 % FS,
Resolution: 1 V.
Mains Frequency : 5 to 99.9Hz (min. 20 VAC Ph-N) Accuracy: 0,25 % FS,
Resolution: 0,1 Hz.
Generator Voltage Measurement : 3 to 300 VAC Ph-N, 5 to 99.9 Hz. Accuracy: 1 % FS,
Resolution: 1 V.
Generator Frequency : 5 to 99.9Hz (min. 20 VAC Ph-N) Accuracy: 0,25 % FS,
Resolution: 0,1 Hz.
Magnetic Pickup Input : 35 to 10000 Hz (1 to 35 volts peak continuously).
Accuracy: 0,25 % FS.
CT secondary : 5A.
Charge Generator Excitation : 210mA @12V, 105mA @24V. Nominal 2.5W.
Charge Gen. Vol. Measurement : 8 to 32 V Z, accuracy: 1 % FS, resolution: 0,1 V.
Sender Measurement : 0 to 1300 ohm, accuracy: 1 % FS, resolution: 1 ohm.
Canbin Temp. Measurement : -50 to +100 C, accuracy: 1 % FS, resolution: 1 C.
Communication interface : USB programming and communication port,
CanBus communication with 1939 ECU
Optional Expansion I/O Module : Expansion I/O module including 8 inputs and 8 outputs.
Optional Comm. Modules : Ethernet/Dial-up, GSM/GPRS, RS-485, Dual Set,
Web Server and GPRS-Web modules.
Relay Outputs : Generator contactor relay output 8A@250VV
Mains contactor relay output 8A@250VV
Configurable output-5 5A@250VV
Configurable output-6 5A@250VV
Transistor Outputs : Fuel or Configurable output-1 1A at DC supply voltage
Crank or Configurable output-2 1A at DC supply voltage
Configurable output-3 1A at DC supply voltage
Configurable output-4 1A at DC supply voltage
All transistor ouputs supplied from DC supply terminal 22
27
6. Other Informations
Manufacturer Information:
Emko Elektronik Sanayi ve Ticaret A..
Demirta Organize Sanayi Blgesi Karanfil Sk. No:6 16369
BURSA/TURKEY

Phone : +90 224 261 1900

Fax : +90 224 261 1912

Repair and maintenance service information:

Emko Elektronik Sanayi ve Ticaret A..
Demirta Organize Sanayi Blgesi Karanfil Sk. No:6 16369
BURSA/TURKEY
Phone : +90 224 261 1900
Fax : +90 224 261 1912

Thank you very much for your preference to use Emko Elektronik
products, please visit our web page to download detailed user
Your Technology Partner manual. www.emkoelektronik.com.tr
28