2-way Control Valves type H1F, Cast steel 2.4.

02-J
PN 40, DN 15/4 50 mm GB-1

Characteristics Dimensioning
Nominal pressure PN 40 For sizing of control valves and selection
k of actuators, please see "Quick Choice"
Regulating capability kvs > 25
vr
leaflet no. 9.0.00.
Single-seated, tight closing
Quadratic characteristic

Design
Applications The valve components - spindle, seat and
cone - are made of stainless steel.
Control valves type H1F are designed
The valve body is made of cast steel
for regulating hot water, steam and hot
GP240GH (GS-C25) with flanges drilled
oil systems.
according to EN 1092-1 or ANSI B16.5
The valves are used in conjunction with
Class 150. The thread for the actuator
our temperature or pressure differen-
connection is G1B ISO 228.
tial regulators for controlling industrial
The valves are single-seated and designed
processes, district or central heating
for tight closure. The leakage rate is less Function
plants or marine installations.
than 0.05% of the full flow (according to
Without the actuator being connected, the
VDI/VDE 2174).
valve is held in open position by means
of a spring. With pressure on the spindle
Pressure/Temperature Diagram the valve will close.
Quality assurance In connection with our thermostats or
All valves are manufactured under an ISO electronic actuators, the valves will close
Bar
9001 certification and are pressure and at rising temperatures. For cooling circuits
40
leakage tested before shipment. a reverse acting valve can be used.
For marine applications the valves can The quadratic characteristic will not cease
30
be supplied with relevant test certificates until the flow has dropped below 4% of
24
from recognized classification societies. the full flow.
20

10
Technical Data
Materials:
-10 120 200 300 350 oC
Valve body Cast steel
GP240GH
(GS-C25)
- trim Stainless steel
- bolts, nuts 24 CrMo 4/A4
Specifications Nominal pressure PN 40
Flange connection Opening kvs-value Lifting height Weight Seating Single seated
Type
DN in mm mm m3/h mm kg Flow characteristic Quadratic
k
15 / 4 H1F 15 4 0.20 6 3.3 Regulating capability kvs > 25
vr
15 / 6 H1F 15 6 0.45 6 3.3 Seat leakage 0.05% of kvs
15 / 9 H1F 15 9 0.95 6 3.4 Temperature range See diagram
15 / 12 H1F 15 12 1.7 6 3.4 Mounting See page 2
15 H1F 15 15 2.75 6 3.4 Flanges drilled
20 / 4 H1F 20 4 0.2 6.5 4.7 according to EN 1092-1 PN 40
20 / 6 H1F 20 6 0.45 6.5 4.7 or ANSI B16.5
20 / 9 H1F 20 9 0.95 6.5 4.7 Class 150
20 H1F 20 20 5 6.5 4.9 Counter flanges DIN 2635
25 H1F 25 25 7.5 7 6.1 Colour Green
32 H1F 32 32 12.5 8 9.0
40 H1F 40 40 20 9 10.8
50 H1F 50 50 30 10 15.5
Subject to changes without notice.

Clorius Controls A/S

Tempovej 27 DK-2750 Ballerup Denmark
Tel.: +45 77 32 31 30 Fax: +45 77 32 31 31
E-mail: [email protected]
Web: www.cloriuscontrols.com
2-way Control Valves type H1F, Cast steel 2.4.02-J
PN 40, DN 15/4 50 mm GB-2

Definition of kvs-value
The kvs-value is identical to the IEC flow Dimension sketch
coefficient kv and defined as the water
flow rate in m3/h through the fully open
G1B
valve by a constant differential pressure,
pv, of 1 bar.
b

Mounting H1
Up to 170C the valve can be installed
vertically as well as horizontally. For
media temperature above 170C, a D k
cooling unit of type KS has to be applied.
It must then be installed with actuator/
H2
thermostats downwards, and according d
to the following instructions:

Valve Cooling Suitable

L
Temperature Unit for

170C - 250C KS-4 All actuators

250C - 350C KS-5 Thermostats
250C - 350C KS-6 Valve Motors
Dimensions
EN 1092-1 ANSI B16.5 Class 150
Strainer
It is recommended to use a strainer in D k d mm D k d mm
L H1 H2 b
front of the control valve if the liquid con- Type (dia.) (dia.) dia. (dia.) (dia.) dia.
mm mm mm mm
tains suspended particles. mm mm (number) mm mm (number)
15 / 4 H1F 130 80 60 16 95 65 14x(4) 89 61 16x(4)
15 / 6 H1F 130 80 60 16 95 65 14x(4) 89 61 16x(4)
Accessories 15 / 9 H1F 130 80 60 16 95 65 14x(4) 89 61 16x(4)
Manual Adjusting Device
15 / 12 H1F 130 80 60 16 95 65 14x(4) 89 61 16x(4)
15 H1F 130 80 60 16 95 65 14x(4) 89 61 16x(4)
20 / 4 H1F 150 85 65 18 105 75 14x(4) 98 70 16x(4)
20 / 6 H1F 150 85 65 18 105 75 14x(4) 98 70 16x(4)
The device has a built-in stuffing box. For 20 / 9 H1F 150 85 65 18 105 75 14x(4) 98 70 16x(4)
sealing and manual operation of valves 20 H1F 150 85 65 18 105 75 14x(4) 98 70 16x(4)
when an actuator has not been fitted, e.g.
25 H1F 160 95 70 18 115 85 14x(4) 108 79 16x(4)
during periods of construction.
32 H1F 180 105 75 18 140 100 18x(4) 118 89 16x(4)
Cooling Unit KS-4 40 H1F 200 110 85 18 150 110 18x(4) 127 98 16x(4)
50 H1F 230 125 95 20 165 125 18x(4) 153 121 19x(4)

Cooling unit protecting the stuffing box

of the motor/thermostat. To be applied
at valve temperatures between 170C
and 250C.

Cooling Unit KS-5 Cooling Unit KS-6

Cooling units with built-in bellow glands, replacing stuffing box of thermostat (KS-5) or
valve motor (KS-6). Must be applied at valve temperatures above 250C. Subject to changes without notice.

Clorius Controls A/S

Tempovej 27 DK-2750 Ballerup Denmark
Tel.: +45 77 32 31 30 Fax: +45 77 32 31 31
E-mail: [email protected]
Web: www.cloriuscontrols.com