Scribd
Upload
68 views

Material Science 1 Assignment 2

The document discusses various topics in materials science: 1) It describes TTT diagrams and how they relate the critical cooling rate to the hardenability of steel. Titanium alloys are discussed for their strength, toughness, and corrosion resistance. 2) Surface hardening processes for low-carbon steel include case hardening and nitriding. Brine provides benefits over water for quenching. Additives can modify aluminum and silicon alloys. 3) S-N curves relate stress levels to the number of cycles to failure in fatigue testing of materials.

Uploaded by

Mehul Bansal
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
68 views

Material Science 1 Assignment 2

The document discusses various topics in materials science: 1) It describes TTT diagrams and how they relate the critical cooling rate to the hardenability of steel. Titanium alloys are discussed for their strength, toughness, and corrosion resistance. 2) Surface hardening processes for low-carbon steel include case hardening and nitriding. Brine provides benefits over water for quenching. Additives can modify aluminum and silicon alloys. 3) S-N curves relate stress levels to the number of cycles to failure in fatigue testing of materials.

Uploaded by

Mehul Bansal
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

Material Science 1

Assignment 2

Ans. 1) a) TTT Curve Diagrams: When plain carbon steel in the austenitic state is quenched to room
temperature, it changes very quickly to martensite. However quenching to temperatures in the 250 o
– 550oC range, give structures intermediate between martensite and pearlite since there is
insufficient atomic mobility to form the cementite laminations of pearlite. The carbide is then
precipitated as fine platelets.

In each case there is a time lag or incubation period before the austenite starts to transform, and the
transformation itself takes a definite time. This is shown by an TTT Curve diagrams which is the
critical cooling rate. The slower the critical cooling rate the better is the hardenability of the steel.

b) Advantages of Titanium alloys: Such alloys have very high tensile strength and toughness (even at


extreme temperatures), light weight, extraordinary corrosion resistance, and ability to withstand
extreme temperatures.
For most applications titanium is alloyed with small amounts of aluminium and vanadium, typically
6% and 4% respectively, by weight. This mixture has a solid solubility which varies dramatically with
temperature, allowing it to undergo precipitation strengthening

Applications: Used for military , aircraft, spacecraft, medical devices, connecting rods on


expensive sports cars and some premium sports equipment and consumer electronics

c) Surface hardening of plain low carbon steel: Since such steels have low carbon content, they must
have a hard surface or ‘skin’ induced around them by a method known as ‘case hardening’.

The steel to be case hardened is packed in a box containing a carbon rich compound and heated in a
furnace. After soaking, the part is quenched with the resulting structure having a very tough core
and a hard outer case.

d) Nitriding: It is a process which introduces nitrogen into the surface of a material which requires the
use of special steels- nitralloy steels eg. Al, Cr, V.

Processes are named by the medium used to donate nitrogen. The three main methods used are:

 Gas nitriding
 Liquid or salt bath nitriding
 Ion or plasma nitriding

Gas nitriding

In gas nitriding the donor is a nitrogen rich gas usually ammonia (NH 3). When ammonia comes into
contact with the heated work piece it disassociates into nitrogen and hydrogen. The nitrogen then
diffuses from the surface into the core of the material.

Salt bath nitriding

In salt bath nitriding the nitrogen donating medium is a nitrogen containing salt such as cyanide salt.
The salts used also donate carbon to the workpiece surface making salt bath a nitrocarburising
process. The temperature used is typical of all nitrocarburising processes; 550-590 oC.
Plasma nitriding

For this process an ionized gas like nitrogen is used in a vacuum chamber at a low pressure when
the electronic characteristics of the gas come into act making it penetrate the surface of the material
being treated.

e) Advantage of using brine: Brine is the result of dissolving common rock salt in water. This mixture
reduces the absorption of atmospheric gases that, in turn, reduces the amount of bubbles. As a
result, brine wets the metal surface and cools it more rapidly than water. In addition to rapid and
uniform cooling, the brine removes a large percentage of any scale that may be present.

f) Modification with respect to aluminium and silicon alloys: It means to impart the desired
properties in aluminium and silicon alloys with the addition of compounds such as p-
bis(dimethylsilyl) benzene, tris(dimethylsilyl) amine, triethylsilane, etc. They increases the tensile
strength of the alloys.

They reduce the scrap rate and help increase the productivity by:-

 Improving mechanical properties


 Improving machinability
 Reducing hot tearing
 Reducing the time required for heat treatment processes
 Controlling porosity distribution
 Reducing the standard deviation
 Reducing die sticking
 Suppressing primary silicon formation
g) Interstitial as applied to metallic lattice structure:  is related to a crystalline compound in which
usually small atoms or ions of a non-metal occupy holes between the larger metal atoms or ions in
the crystal lattice. So it is the space available for the impurities between the crystalline lattice
structures.

h) Unsuitability of tough pitch copper for welding: Since it contains 0.02-0.05% oxygen (as cuprous
oxide Cu2O), using it in reducing atmosphere above 400 oC as in gas welding, makes the oxygen
present to give steam which cannot escape (molecules too large for diffusion) and therefore causes
porosity known as ‘gassing’.

i) Advantages of grey cast iron:

 Good compression strength and damping capacity (ability to absorb vibrations).


 Easily machinable and is easier and cheaper to cast than steel (MP about 1150 oC as against
1550oC for steel).

Applications:

 Machines bases and frames


 Engine blocks
 Manholes and drain covers

j) S-N Curves: S-N curves are derived from tests on samples of the material to be characterised,
where a regular sinusoidal stress is applied by a testing machine which also counts the number of
cycles to failure. These curves show that how the stress levels in the test specimen decrease with the
increases in the number of cycles.

Ans. 2) a) ii) Phase changes for a 80% Cu, 20% Zn composition alloy: A 80% Cu, 20% Zn composition
alloy starts its transformation from a liquid state into a liquid + alpha region at around 1050oC which
completes at 1000oC where it completely transforms into an alpha state.

iii) Unsuitability of gamma phase for commercial purposes:

 Brass undergoes maximum elongation at 30% Zn concentration.


 The ultimate tensile strength is maximum at about 46% Zn concentration.
 A good combination of strength and elongation is achieved at 40% Zn concentration.
But, the gamma phase in brass is present when the concentration of Zn exceeds beyond 49% making
it loose both its strength and the ability to withstand elongation which makes it unsuitable for
commercial applications.

iv) Addition of lead to improve the machinability: The addition of lead upto 5% helps the chips to
break easily during the machining of brass as it precipitates into soft inclusions which provide
lubrication and weak points in the chips.

v) Alloying elements that are added to Cu Zn alloys to form high tensile brasses:

 Manganese
 Aluminium
 Tin
 Iron
 Nickel

You might also like