Scribd
Upload
100 views3 pages

TutoRFID2 Ino

This document contains code for reading RFID tags using an MFRC522 module connected to an Arduino board. It initializes the MFRC522 module, reads the UID from tags, compares it to a list of authorized tags, and lights an LED green if authorized or red if unauthorized. The code prints the tag UID to the serial monitor and halts reading after 2 seconds.

Uploaded by

Younj'a
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
100 views3 pages

TutoRFID2 Ino

This document contains code for reading RFID tags using an MFRC522 module connected to an Arduino board. It initializes the MFRC522 module, reads the UID from tags, compares it to a list of authorized tags, and lights an LED green if authorized or red if unauthorized. The code prints the tag UID to the serial monitor and halts reading after 2 seconds.

Uploaded by

Younj'a
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 3

/*

*
-----------------------------------------------------------------------------------
---------------------------------
* Example sketch/program showing how to read new NUID from a PICC to serial.
*
-----------------------------------------------------------------------------------
---------------------------------
* This is a MFRC522 library example; for further details and other examples see:
https://github.com/miguelbalboa/rfid
*
* Example sketch/program showing how to the read data from a PICC (that is: a RFID
Tag or Card) using a MFRC522 based RFID
* Reader on the Arduino SPI interface.
*
* When the Arduino and the MFRC522 module are connected (see the pin layout
below), load this sketch into Arduino IDE
* then verify/compile and upload it. To see the output: use Tools, Serial Monitor
of the IDE (hit Ctrl+Shft+M). When
* you present a PICC (that is: a RFID Tag or Card) at reading distance of the
MFRC522 Reader/PCD, the serial output
* will show the type, and the NUID if a new card has been detected. Note: you may
see "Timeout in communication" messages
* when removing the PICC from reading distance too early.
*
* @license Released into the public domain.
*
* Typical pin layout used:
*
-----------------------------------------------------------------------------------
------
* MFRC522 Arduino Arduino Arduino Arduino
Arduino
* Reader/PCD Uno/101 Mega Nano v3 Leonardo/Micro Pro
Micro
* Signal Pin Pin Pin Pin Pin Pin
*
-----------------------------------------------------------------------------------
------
* RST/Reset RST 9 5 D9 RESET/ICSP-5 RST
* SPI SS SDA(SS) 10 53 D10 10 10
* SPI MOSI MOSI 11 / ICSP-4 51 D11 ICSP-4 16
* SPI MISO MISO 12 / ICSP-1 50 D12 ICSP-1 14
* SPI SCK SCK 13 / ICSP-3 52 D13 ICSP-3 15
*/

#include <SPI.h>
#include <MFRC522.h>

#define SS_PIN 53
#define RST_PIN 5

MFRC522 rfid(SS_PIN, RST_PIN); // appel de la classe

#define PIN_LED_VERTE 8
#define PIN_LED_ROUGE 9

// liste cls valides


String keyOk[]={"15 c4 2d 5","15 c4 2d 6"};
void setup() {
Serial.begin(57600);
SPI.begin(); // Init SPI bus
rfid.PCD_Init(); // Init MFRC522

pinMode(PIN_LED_VERTE,OUTPUT);
pinMode(PIN_LED_ROUGE,OUTPUT);

// led eteintes a l'init


digitalWrite(PIN_LED_VERTE,LOW);
digitalWrite(PIN_LED_ROUGE,LOW);
}

void loop() {

// Si on ne detecte pas une carte on reboucle au debut


if ( ! rfid.PICC_IsNewCardPresent())
return;

// as t'on lu la carte
if ( ! rfid.PICC_ReadCardSerial())
return;

// recuperation de l'UID et concatnation de sa valeur en hex dans un string


String myKey=String(rfid.uid.uidByte[0],HEX) + " " +
String(rfid.uid.uidByte[1],HEX) + " " + String(rfid.uid.uidByte[2],HEX) + " " +
String(rfid.uid.uidByte[3],HEX);

// j'affiche la valeur de la carte sur le serial


Serial.println(myKey);

bool accessOk = 0;
// je boucle sur toutes les valeurs des cls autoriss et si je la trouve accesOK
=> 1
for(int y = 0; y < (sizeof(keyOk)/sizeof(String)) ; y++){

if(keyOk[y] == myKey){
accessOk = 1;
}

// Halt PICC, fin de lecture de carte


rfid.PICC_HaltA();

// Stop encryption on PCD


rfid.PCD_StopCrypto1();

// La carte as t'elle acces , si oui led verte , si non led rouge


if(accessOk == 1){
digitalWrite(PIN_LED_VERTE,HIGH);
}
else{
digitalWrite(PIN_LED_ROUGE,HIGH);
}
// on eteind les led apres un delais
delay(2000);
digitalWrite(PIN_LED_VERTE,LOW);
digitalWrite(PIN_LED_ROUGE,LOW);

You might also like