Projector Manual 4854

Download as pdf or txt
Download as pdf or txt
You are on page 1of 50

Operating Instructions

DLPBased Projector Commercial Use

Model No. PT-DZ6710U


PT-DZ6700U
PT-DW6300U
PT-D6000U

STANDBY(RED)/ LAMP TEMP FILTER


ON(GREEN)

Before operating this product, please read the instructions carefully and save this manual for future use.
The information of these instructions are shared use with multiple models of DZ6710 series, DZ6700 series, DW6300 series
and D6000 series.

TQBJ0295

ENGLISH
Important Safety Notice
Information
Important

Dear Panasonic Customer:


The following information should be read and understood as it provides details, which will enable you to operate the
projector in a manner which is both safe to you and your environment, and conforms to legal requirements regarding
the use of projectors. Before connecting, operating or adjusting this projector, please read these instructions
completely and save this booklet with the projector for future reference. We hope it will help you to get the most out
of your new product, and that you will be pleased with your Panasonic DLPBased Projector.
The serial number of your product may be found on its bottom. You should note it in the space provided below and
retain this booklet in case service is required.

Model number: PT-DZ6710U/PT-DZ6700U/PT-DW6300U/PT-D6000U

Serial number:

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DONOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.

Power Supply: This LCD Projector is designed to operate on 100 V - 240 V, 50 Hz/60 Hz AC, house current
only.

CAUTION: The AC power cord which is supplied with the projector as an accessory can only be used for
power supplies up to 125 V, 7 A. If you need to use higher voltages or currents than this, you will
need to obtain a separate 250 V power cord. If you use the accessory cord in such situations, fire
may result.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the
user to the presence of uninsulated dangerous voltage within the products enclosure that may
be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature accompanying the
product.

CAUTION: This equipment is equipped with a three-pin grounding-type power


plug. Do not remove the grounding pin on the power plug. This plug
will only fit a grounding-type power outlet. This is a safety feature. If
you are unable to insert the plug into the outlet, contact an electrician.
Do not defeat the purpose of the grounding plug.
Do not remove

Pursuant to at the directive 2004/108/EC, article 9(2)


Panasonic Testing Center
Panasonic Service Europe, a division of Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, F.R. Germany

ENGLISH - 2
Important Safety Notice

Information
Important
NOTICE:
A This product has a High Intensity Discharge (HID) lamp that contains mercury. Disposal may be regulated in
your community due to environmental considerations. For disposal or recycling information, please contact
your local authorities, or the Electronic Industries Alliance: http://www.eiae.org

WARNING:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION: To assure continued compliance, follow the attached installation instructions and use only
shielded interface cables when connecting to computer and/or peripheral devices. Any
changes or modifications not expressly approved by Panasonic Corp. of North America could
void the user's authority to operate this device.

WARNING:
A Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/Data
Processing Equipment, ANSI/NFPA 75.
A For permanently connected equipment, a readily accessible disconnect device shall be incorporated in the
building installation wiring.
A For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily
accessible.

Declaration of Conformity
Model Number: PT-DZ6710U/PT-DZ6700U/PT-DW6300U/PT-D6000U
Trade Name: Panasonic
Responsible party: Panasonic Corporation of North America
Address: One Panasonic Way, Secaucus, New Jersey 07094
Telephone number: (888) 411 - 1996
E-mail: projectorsupport@us.panasonic.com
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.

ENGLISH - 3
Important Safety Notice
Information
Important

Information on Disposal in other Countries outside the European


These symbols are only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and ask for the correct
method of disposal.

ENGLISH - 4
Contents

Information
Important
J Quick steps
Getting Started
1. Set up your projector Setting up.................................................................. 16
Projection method........................................................... 16
See Setting up on page 16. Removing and attaching the projection lens................... 17
Power cord ..................................................................... 18

Basic Operation
Projecting.................................................................. 19

Preparation
2. Connect with other devices Projecting a image.......................................................... 19
See the functional instructions in the Remote control operation........................................ 21
Operating range.............................................................. 21
CD-ROM that is provided with the Setting up the image position automatically ................... 21
projector. Switching the input signal ............................................... 22
Stopping the projection................................................... 22
Clearing the screen ........................................................ 22
Changing the picture aspect ratio................................... 22
Displaying the internal test pattern ................................. 22
Using an assigned function ............................................ 23
Displaying the status of the projector ............................. 23

Getting Started
3. Prepare the Remote control Resetting to the factory default....................................... 23
See Remote control on page 14. Menu Navigation....................................................... 24
Main menu and Sub-menu ............................................. 24
Navigating through the menu ......................................... 27

Maintenance
Monitor Lamp indicators ......................................... 28
4. Start projecting Managing the indicated problems................................... 28
See Projecting on page 19. Replacement ............................................................. 30
Replacing the Lamp unit................................................. 30

Basic Operation
Replacing the Auto Cleaning Filter (ACF) ...................... 31
Troubleshooting ....................................................... 33

Appendix
Technical Information .............................................. 34
List of compatible signals ............................................... 34
5. Adjust the image Specifications ................................................................. 36
See Menu Navigation on page 24. Dimensions..................................................................... 38
Trademark acknowledgements ...................................... 38
Index .......................................................................... 39
Avis important concernant la scurit ................... 41 Maintenance
Prcautions de scurit........................................... 43
Important Information AVERTISSEMENT ......................................................... 43
MISES EN GARDE......................................................... 44
Important Safety Notice ..............................................2 Prcautions lors du transport.......................................... 45
Precautions with regard to safety .............................6 Prcautions lors de l'installation ..................................... 46
WARNINGS ...................................................................... 6 Prcautions lors de l'utilisation ....................................... 46
CAUTIONS ....................................................................... 7 Autres ............................................................................. 46
Cautions when transporting .............................................. 9 Scurit .......................................................................... 47
Cautions when installing ................................................... 9 Remplacement.......................................................... 48
Cautions on use ................................................................ 9
Others ............................................................................. 10
Security ........................................................................... 10
Accessories..................................................................... 11
Appendix

Preparation
About Your Projector................................................12
Projector body................................................................. 12
Remote control................................................................ 14

ENGLISH - 5
Precautions with regard to safety
Information
Important

WARNINGS
If you notice smoke, strange smells or noise coming Insert the power plug securely into the wall outlet.
from the projector, disconnect the power plug from Do not use other than the provided power cord.
the wall outlet. If the plug is not inserted correctly, electric shocks or
Do not continue to use the projector in such cases, overheating could result.
otherwise fire or electric shocks could result. Do not use plugs which are damaged or wall outlets
Check that no more smoke is coming out, and then which are coming loose from the wall.
contact an Authorized Service Center for repairs.
Do not attempt to repair the projector yourself, as this Do not place the projector on top of surfaces which
can be dangerous. are unstable.
If the projector is placed on top of a surface which is
Do not install this projector in a place which is not sloped or unstable, it may fall down or tip over, and
strong enough to take the full weight of the injury or damage could result.
projector.
If the installation location is not strong enough, it may Do not place the projector into water or let it become
fall down or tip over, and severe injury or damage wet.
could result. Failure to observe this may result in fire or electric
shocks.
Installation work (such as ceiling suspension)
should only be carried out by a qualified technician. Do not do anything that might damage the power
If installation is not carried out correctly, there is the cord or the power plug.
danger that injury or electric shocks may occur. Do not damage the power cord, make any
Do not use other than an authorized ceiling mount modifications to it, place it near any hot objects, bend
bracket. it excessively, twist it, pull it, place heavy objects on
top of it or wrap it into a bundle.
If foreign objects or water get inside the projector, or If the power cord is used while damaged, electric
if the projector is dropped or the cabinet is broken, shocks, short-circuits or fire may result.
disconnect the power plug from the wall outlet. Ask an Authorized Service Center to carry out any
Continued use of the projector in this condition may repairs to the power cord that might be necessary.
result in fire or electric shocks.
Contact an Authorized Service Center for repairs. Do not place the projector on soft materials such as
carpets or sponge mats.
The wall outlet shall be installed near the equipment Doing so may cause the projector to overheat, which
and shall be easily accessible. can cause burns, fire or damage to the projector.
Unplug the power plug from the wall outlet
immediately when problem occurred. Do not place liquid containers on top of the
projector.
Do not overload the wall outlet. If water spills onto the projector or gets inside it, fire
If the power supply is overloaded (for example, by or electric shocks could result.
using too many adapters), overheating may occur If any water gets inside the projector, contact an
and fire may result. Authorized Service Center.

Never attempt to modify or disassemble the Do not insert any foreign objects into the projector.
projector. Do not insert any metal objects or flammable objects
High voltages can cause fire or electric shocks. into the projector or drop them onto the projector, as
For any inspection, adjustment and repair work, doing so can result in fire or electric shocks.
please contact an Authorized Service Center.
Do not allow the + and - terminals of the batteries to
Clean the power plug regularly to prevent it from come into contact with metallic objects such as
becoming covered in dust. necklaces or hairpins.
If dust builds up on the power plug, the resulting Failure to observe this may cause the batteries to
humidity can damage the insulation, which could leak, overheat, explode or catch fire.
result in fire. Pull the power plug out from the wall Store the batteries in a plastic bag and keep them
outlet and wipe it with a dry cloth. away from metallic objects.
If not using the projector for an extended period of
time, pull the power plug out from the wall outlet.

Do not handle the power plug with wet hands.


Failure to observe this may result in electric shocks.

ENGLISH - 6
Precautions with regard to safety

Information
Important
Do not touch the leaked liquid from the batteries. When replacing the lamp, allow it to cool for at least
If you touch the leaked liquid, it may hurt your skin. one hour before handling it.
Immediately wash away the liquid with water and The lamp cover gets very hot, and touching it can
seek medical advice. cause burns.
If you get the leaked liquid in your eye, it may cause
blindness or damage. Never rub your eye, and Before replacing the lamp, be sure to disconnect the
immediately wash away the liquid with water and power plug from the wall outlet.
seek medical advice. Electric shocks or explosions can result if this is not
done.
During a thunderstorm, do not touch the projector or
the cable. Do not allow infants or pets to touch the remote
Electric shocks can result. control unit.
Keep the remote control unit out of the reach of
Do not use the projector in a bath or shower. infants and pets after using it.
Fire or electric shocks can result.
After removing the battery from remote control unit,
Do not place your skin into the light beam while the keep it away from the reach of children.
projector is being used. The battery can cause death by suffocation if
Strong light is emitted from the projectors lens. If you swallowed.
place directly into this light, it can hurt or damage If the battery is swallowed, seek medical advice
your skin. immediately.

Do not look into the lens while the projector is being Insulate the battery using tape or similar before
used. disposal.
Strong light is emitted from the projectors lens. If you If the battery comes into contact with metallic objects
look directly into this light, it can hurt and damage or other batteries, it may catch fire or explode.
your eyes.
When installing to a ceiling, be sure to use the
Do not disassemble the lamp unit. accessory wire (install in a different location to the
If the lamp section breaks, it may cause injury. ceiling mount bracket) and the eye bolts as an extra
preventative measure to stop the projector from
Do not place your hands or other objects close to the falling down.
air outlet port. If the projector is not secure enough, accidents may
Heated air comes out of the air outlet port. Do not result.
place your hands or face, or objects which cannot
withstand heat close to this port [allow at least Do not place sets directly on top of each other.
50 cm (20") of space], otherwise burns or damage If this is not observed, accidents may result.
could result.
Do not use the projector while the projection lens
Replacement of the lamp should be carried out by a cover is still attached to the projection lens.
qualified technician. If this is not observed, fire may occur.
The lamp has high internal pressure. If improperly
handled, explosion might result.
The lamp can easily become damaged if struck
against hard objects or dropped, and injury or
malfunctions may result.

CAUTIONS
Do not cover the air inlet port or the air outlet port. Do not set up the projector in humid or dusty places
Doing so may cause the projector to overheat, which or in places where the projector may come into
can cause fire or damage to the projector. contact with oily smoke or steam.
Do not place the projector in narrow, badly ventilated Using the projector under such conditions may result
places such as closets or bookshelves. in fire, electric shocks or plastic deterioration. The
Do not place the projector on cloth or papers, as plastic deterioration may cause the falling down of
these materials could be drawn into the air inlet port. the projector which is mounted on the ceiling.

ENGLISH - 7
Precautions with regard to safety
Information
Important

Do not set up the projector in a high temperature If not using the projector for an extended period of
environment, such as near a heater or in direct time, disconnect the power plug from the wall outlet
sunlight. and remove the batteries from the remote control.
Failure to observe this may result in fire, malfunction If dust builds up on the power plug, the resulting
or plastic deterioration. humidity may damage the insulation, which could
result in fire.
Do not set up the projector outdoors. Keeping or leaving the remote control with batteries
The projector is designed for indoor use only. inside may cause insulation deterioration, electrical
leakage or explosion which could result in fire.
When disconnecting the power cord, hold the plug,
not the cord. Do not use the old lamp unit.
If the power cord itself is pulled, the cord will become The lamp section may break.
damaged, and fire, short-circuits or serious electric
shocks may result. Do not put your weight on this projector.
You could fall or the projector could break, and injury
Always disconnect all cables before moving the may result.
projector. Be especially careful not to let young children stand
Moving the projector with cables still attached can or sit on the projector.
damage the cables, which could cause fire or electric
shocks to occur. Disconnect the power plug from the wall outlet as a
safety precaution before carrying out any cleaning.
Do not place any heavy objects on top of the Electric shocks can result if this is not done.
projector.
Failure to observe this may cause the projector to If the lamp has broken, ventilate the room
become unbalanced and fall, which could result in immediately. Do not touch or bring your face close
damage or injury. to the broken pieces.
Failure to observe this may cause the user to absorb
Do not short-circuit, heat or disassemble the the gas which was released when the lamp broke and
batteries or place them into water or fire. which contains nearly the same amount of mercury
Failure to observe this may cause the batteries to as fluorescent lamps, and the broken pieces may
overheat, leak, explode or catch fire, and burns or cause injury.
other injury may result. If you believe that you have absorbed the gas or that
the gas has got into your eyes or mouth, seek
When inserting the batteries, make sure the medical advice immediately.
polarities (+ and -) are correct. Ask your dealer about the replacement of the lamp
If the batteries are inserted incorrectly, they may unit and check the inside of the projector.
explode or leak, and fire, injury or contamination of
the battery compartment and surrounding area may Ask an Authorized Service Center to clean inside the
result. projector at least once a year.
If dust is left to build up inside the projector without
Use only the specified batteries. being cleaned out, it can result in fire or problems
If incorrect or different kind of batteries are used, they with operation.
may explode or leak, and fire, injury or contamination It is a good idea to clean the inside of the projector
of the battery compartment and surrounding area before the season for humid weather arrives. Ask
may result. your nearest Authorized Service Center to clean the
projector when required. Please discuss with the
Do not mix old and new batteries.
Authorized Service Center regarding cleaning costs.
If the batteries are used mixing old and new, they
may explode or leak, and fire, injury or contamination Do not use chemical treated wipes when cleaning.
of the battery compartment and surrounding area Using chemical treated wipes may result in plastic
may result. distortion or deterioration.
Remove the used batteries from the remote control
promptly.
If you leave used batteries in the remote control for
an extended period of time, it may cause liquid
leaking, abnormal internal temperature rising or
explosion.

ENGLISH - 8
Precautions with regard to safety

Information
Important
Do not reach for the openings beside the optical Replacement of the lamp unit should only be carried
lens, during horizontal or vertical movements of the out after it has completely cooled off.
lens. Failure to observe this may cause burns.
Failure to observe this may cause injury.

We are constantly making efforts to preserve and maintain a clean environment. Please take non repairable
units back to your dealer or a recycling company.

Cautions when transporting


Do not subject the projector to excessive vibration When transporting the projector, hold the body at
or shocks. the bottom securely.
The projector lens need to be handled with care. Do not hold the adjuster legs or the top cover to move
Cover the lens with the lens cover when transporting the projector, as this may damage the projector.
the projector.
Be sure to always remove the lens during transport.
The projection lens is susceptible to vibrations and
impacts.

Cautions when installing


Avoid setting up in places which are subject to If installing the projector to the ceiling, ask a
vibration or shocks. qualified technician to carry out all installation work.
The internal parts can be damaged, which may cause You will need to purchase the separate installation kit
malfunctions or accidents. (Model No. ET-PKF100H, ET-PKF100S).
Furthermore, all installation work is should only be
Avoid setting up in places which are subject to carried out by a qualified technician.
sudden temperature changes, such as near an air
conditioner or lighting equipment. If using this projector at high elevations 1 400 -
The life of the lamp may be shortened or the projector 2 700 m (4 593 - 8 858 ft) sea level, set the HIGH
may be turned off. See TEMP indicator on page 28. ALTITUDE MODE to ON.
Failure to observe this may result in malfunctions or
Do not set up the projector near high-voltage power the life of the lamp or the other components may be
lines or near motors. shortened.
The projector may be subject to electromagnetic
interference. Be sure to install the projection lens cover after
installing the projection lens.
If this not done, dust will collect inside the projector
and problems with the projector will result.

Cautions on use
In order to get the best picture quality Do not touch the surfaces of the lens or the front
Draw curtains or blinds over any windows and turn off glass with your bare hands.
any lights near the screen to prevent outside light or If the surface of the lens becomes dirty from
light from indoor lamps from shining onto the screen. fingerprints or anything else, this will be magnified
In rare cases, wafture can occur on the screen and projected onto the screen. Moreover, when not
affected by the warm air from the exhaust port using the projector, close the front panel cover.
depending on the environment. Make sure that there
is no equipment in front of the set which will
recirculate the exhaust air from the set or other
nearby equipment.

ENGLISH - 9
Precautions with regard to safety
Information
Important

The projector has a high pressure mercury lamp and Optical components
that is characterized as follows. If you use the projector consecutively 22 hours every
The brightness of the lamp depends on the duration day, the optical components may need to be replaced
of use. in less than 1 year.
The lamp may explode or shorten the lamp life by
shocks or chipping damage. Do not use projectors with the adjustable feet or
The lamp may explode only occasionally after using projection lens cover removed.
the projector. If this is not observed, the sets may not operate
The lamp may explode if using the projector after the correctly or accidents may result.
instructed lamp replacement timing.
When the lamp exploded, it emits internal smoke-like DLP chips
gas. The DLP chips are made using extremely high-
The lamp life is depends on individual lamp precision technology. Note that in rare cases, pixels
characteristics, usage condition and the installation may be missing or always lit, but this is not a
environment. Especially the consecutive use of the malfunction.
projector for more than 22 hours, or the frequent
switching on or off may greatly affect on the lamp life.
Provide a lamp for replacement in advance.

Others
Disposal Connection to external device
When disposing of the product, contact your nearest When connecting the projector to a computer or
municipality or dealer to confirm the correct external device, use the power cord supplied with the
procedure for disposal. corresponding device and a commercially available
shielded interface cable.

Security
Take the safety measures for use of the projector Security instruction
that should cover the following envisioned The connecting network must be secured by firewall
incidents. or others.
The leakage of your personal registered information. Change your password regularly.
Dishonest operation by an untrusted third party. Do not use password too simple to guess.
Locking out or prevent anyone else from using the The Authorized Service Center will never ask you for
projector by an untrusted third party. the password.
Do not share your password with anyone else.
Password the projector and restrict access to
authorized users only.

ENGLISH - 10
Precautions with regard to safety

Information
Important
Accessories
Make sure the following accessories are provided with your projector.

Remote control (x1) AA batteries for remote Safety cable Power cord (x1)
N2QAYB000371 control (x2) TTRA0214 K2CG3FZ00008
Attachment screw (x1)
Safety cable (x1)

Projector lens cover (x1)


TKKL5244-1

CD-ROM (x1)
TQBH9013

Power cord secure lock


(x1)
TTRA0182

* The protectors for enclosed products, such as a plug cover or foam cartons, must be treated properly.
* Contact to an Authorized Service Center for lost accessories.

ENGLISH - 11
About Your Projector
Projector body
J Top, front and bottom view
Indicators
Lamp unit compartment (page 30)
Power indicator
Preparation

Lamp1 (LAMP1) indicator (page 28) Air exhaust port


Lamp2 (LAMP2) indicator (page 28)
Temperature (TEMP) indicator (page 28)
Filter (FILTER) indicator (page 29)

STANDBY(RED)/ LAMP TEMP FILTER


ON(GREEN)

Projection lens
Focus ring
MENU button
Displays and clears the main
STANDBY(RED)/ LAMP TEMP FILTER
ON(GREEN)

POWER ON button menu, and returns to the


Starts the projection while previous menu when the menu
in the standby mode. is displayed. (page 27)
(page 20) LENS button
POWER STANDBY This button is used together with
Remote control signal F G I H to adjust focus, zoom
button
receptor (page 21) and shift by the projection lens.
Returns to the standby
mode. (page 20) (page 19)
Front leg adjusters
Screw up/down to adjust the
projection angle.
Navigation and
ENTER buttons
Navigate through
Burglar hook port Input select buttons the menu items
Attach a commercial burglar These buttons select the with F G I H,
prevention cable. RGB1, RGB2, DVI-D, VIDEO, and activate them
S-VIDEO and SDI with the ENTER
(PT-DZ6710U only) terminals. button. (page 27)
(page 19)

AUTO SETUP button


Pressing this button while projecting an image
automatically corrects the picture positioning on
the screen. While the auto setup feature is active,
a message PROGRESS appears on the screen.
(page 21)
Remote control signal receptor (page 21)
SHUTTER button
Pressing this button toggles the projectors
internal mechanical shutter to black out the
projector. (page 22)

NOTE:
Do not cover the ventilation openings or place anything within 50 cm (20") of them as this may cause damage or injury.
While the projector is not in use, keep the projector lens cover attached to protect the lens.

ENGLISH - 12
About Your Projector
J Side views
S-VIDEO IN
RGB 1 IN
Connect an S-VIDEO signals.
Connect an RGB or YPBPR signals.
(Mini DIN 4 pin)
(3, 4 or 5 wire BNC)
VIDEO IN
RGB 2 IN
Connect a video signals.
Connect an RGB or YPBPR signals.
(BNC)
(D-SUB 15 pin female)

Preparation
LAN
DVI-D IN
Connect a LAN cable for network
Connect a single link DVI-D signals.
connection.
(10BASE-T/100BASE-TX)

REMOTE 1 IN/OUT REMOTE 2 SERIAL IN/SERIAL OUT SDI IN (PT-DZ6710U only)


Connect a cable from the Connect a cable from an Connect an RS-232C cable Connect a cable from a
remote control or another external control circuit. from/to a computer. computer.
projector. (D-sub 9 pin female)
(M3 jack)

Air intake port Air intake port

AC IN terminal
Connect the power cord to supply
POWER button electronic power to the projector.
Switch the projector on/off. (page 20) (page 20)
Security lock
Attach the commercial shackle lock, manufactured
by Kensington, to protect your projector.
Compatible with the Kensington MicroSaver
Security System.

Auto Cleaning Filter (ACF) compartment (page 31)

NOTE:
Switch on the POWER button of the projector body that is located near the terminals before using the control buttons.
Do not cover the ventilation openings or place anything within 50 cm (20") of them as this may cause damage or injury.

ENGLISH - 13
About Your Projector

Remote control
POWER ON and POWER STANDBY Remote control indicator
buttons Flashes by pressing any buttons.
POWER ON: Starts (page 21)
the projection while in AUTO SETUP
the standby mode. Pressing this button while
Preparation

POWER STANDBY: Returns to the projecting an image


standby mode. (page 19) automatically corrects the
INPUT SELECT buttons picture positioning on the screen.
These buttons While the auto setup feature is active,
select the RGB1, a message PROGRESS appears on
RGB2, DVI-D, the screen. (page 21)
VIDEO, S-VIDEO SHUTTER button
and SDI terminals. (page 22) Pressing this button toggles
MENU buttons the projectors internal
Displays and clears the main mechanical shutter to black out
menu, and returns to the the projector. (page 22)
previous menu when the menu ASPECT button
is displayed. (page 27) Switches the image aspect
ON SCREEN button ratio. (page 22)
Displays and clears the on
LENS buttons
screen indications. (page 22)
These buttons
TEST PATTERN button are used
Displays the test pattern. together with
(page 22) F G I H to adjust focus, zoom and
Numeric (0 - 9) buttons shift by the projection lens. (page 19)
Enter ID number of the remote control, FUNCTION button
adjustment values of menu items and Assign the frequently use
by service personnel. (page 15) functions from options for
STATUS button shortcut. (page 23)
Displays projector DEFAULT button
information. (page 23) Restores the default factory
Navigation and ENTER buttons setting. (page 23)
Navigate through the ID buttons
menu items with F G ALL: Makes the remote
I H, and activate them control available to
with the ENTER button. control any ID
(page 27) projectors.
SET: Specifies the ID of the remote
control. (page 15)

A
Top view Bottom view
Remote control signal emitters Remote control wired terminal Battery compartment
1.Press the tab and lift up the cover.
2.Insert the batteries according to the polarity
diagram indicated inside.

NOTE:
Switch on the POWER button of the projector body that is located near the terminals before using the remote control.
Do not drop the remote control.
Avoid contact with liquids or moisture.
Use manganese batteries or alkaline batteries with the remote control.
Do not attempt to modify or disassemble the remote control. Contact an Authorized Service Center for repairs.
Do not keep pressing the remote control buttons as this may shorten battery life.
See Remote control operation on page 21.

ENGLISH - 14
About Your Projector
J Setting projector ID number to J Using a wired remote control
remote control When multiple projectors are connected as part of the
system, connect to units with a M3 stereo mini jack
Each projector can be assigned a unique 2 digits ID
commercial cable to simultaneously control multiple main
number, and the remote control 2 digits ID number must
units with a single remote control through the REMOTE 1
be set to match the intended projector. The default
IN/OUT terminal. It is effective to use the wired remote
setting of the projector ID is ALL. Set the ID of the
control in the environment in which an obstacle stands in
projector in advance from the menu items.
the light path or where devices are susceptible to outside

Preparation
1.Press the ID SET button.
light.
Displays the projector ID number on the screen.
2.Within 5 seconds, enter the same number of the required
projector by pressing the numeric buttons.
ID number range: 01 - 64

NOTE:
Do not press the ID SET button accidentally or carelessly
because the ID number on the remote control can be set even
when no projector is around.
If you do not enter the 2 digits ID number within 5 seconds
after the ID SET button has been pressed, the ID will remain at
the number that was set before the ID SET button was
pressed.
Your specified ID will be erased if the batteries of the remote
control are left exhausted. When the batteries are replaced, Connect to another
set the same ID number again. projector

M3 stereo mini jack


(commercial)

Connect to the remote


control wired terminal

NOTE:
Use 2 core shielded cable of length of 15 m or less. If the
length of the cable exceeds 15 m (49'2"), the shielding of the
cable may not be sufficient and the remote control may not
work.

ENGLISH - 15
Setting up
Projection method
You can use the projector with any of the following 4 projection methods. To set the desired method in the projector,
J Setting on a desk/floor and J Setting on a desk/floor and
projecting from front projecting from rear

INSTALLATION: FRONT/FLOOR INSTALLATION: REAR/FLOOR


Getting Started

COOLING CONDITION: FLOOR SETTING COOLING CONDITION: FLOOR SETTING


J Mounting on the ceiling and J Mounting on the ceiling and
projecting from front projecting from rear

INSTALLATION: FRONT/CEILING INSTALLATION: REAR/CEILING


COOLING CONDITION: CEILING SETTING COOLING CONDITION: CEILING SETTING

NOTE:
A translucent screen is required for rear projection.
See more detailed setting up instructions, INSTALLATION and COOLING CONDITION in PROJECTOR SETUP menu on the functional
instructions in the CD that is provided with the projector.
Do not place or use a projector on top of another projector.
Do not cover the ventilation openings or place anything within 50 cm (20") of them as this may cause damage or injury.

ENGLISH - 16
Setting up

Removing and attaching the projection lens


J Removing the projection lens J Attaching the projection lens to
from the projector the projector
1. Switch off the POWER button on the projector. 1. Switch off the POWER button on the projector.
2. Rotate the lens cover counterclockwise and remove. When the lens cover is attached, rotate counterclockwise
and remove.
2. Align the guide of the projection lens with the guide
groove in the projector, and then insert the lens.
Lens cover

Getting Started
3. While pressing the lens release button, rotate the 3. Rotate the projection lens clockwise until it clicks into
projection lens counterclockwise, and remove the place.
projection lens.

4. Place the lens cover back to the projector, and rotate


clockwise to attach.
Lens release button Projection lens

NOTE:
Do not touch the lens signal contact. Dust or dirt may cause
defective contact.
Do not touch the surface of the projection lens with your bare
hands.
Store the replaced lens where it will be free from vibration and
impact.

NOTE:
Make sure the projection lens is attached securely by rotating
the projection lens counterclockwise.

ENGLISH - 17
Setting up

Power cord
J Connecting J Disconnecting
1. Make sure the shape of the power plug and the AC IN 1. Unplug the power cord from the wall outlet.
terminal on the back of the projector match, then push 2. Depress the latch and slide the cover off.
the plug all the way in.

Latch

2. Align the side of the power cord secure lock with the side
guide rail of the AC IN terminal of the projector and slide 3. Slide the power cord secure lock up along the side guide
it in. rail and remove.
Getting Started

Rail guide Rail guide

3. Place the latch to the latch catcher and press until it


4. Hold the plug and unplug the power cord from the AC IN
clicks.
terminal on the back of the projector.
Power indicator lights in orange if the internal cooling fan is
still operating by internal power supply.

Latch
4. Connect the power cord to a wall outlet.

NOTE:
Do not use other than the provided power cord.
Ensure all the input devices are connected and turned off before connecting the power cord.
Do not force the connector as this may damage the projector and/or the power cord.
Dirt or dust build-up around plugs may cause fire or electrical hazards.
Switch off the power to the projector when not in use.
If the projector is switched on again while the internal cooling fan is still operating by the internal power supply, it may take a while to start
the projection.

ENGLISH - 18
Projecting
Projecting a image
J Switching on the projector J Making adjustment and selection
When using an optional lens, install a projection lens It is recommended that the projector be allowed to warm
before switch on the projector. up for at least 30 minutes before any adjustments are
1. Connect the supplied power cord (220 - 240 V AC, made to the focus.
50 Hz/60 Hz) to the AC IN terminal. 1. Roughly adjust the focus of the lens.
2. Remove the projection lens cover from the lens. 2. Select and set the projection scheme of
3. Switch the POWER switch on that is on the side of the INSTALLATION setting in PROJECTOR SETUP menu.
projector. 3. Select the input signal by pressing the INPUT SELECT
The power indicator lamp on the projector will flash in red. buttons.
After a short period, the indicator will illuminate and the 4. Adjust the vertical tilt of the projector with the front leg
projector will enter standby mode. adjusters.
5. Adjust the shift position of the projection.
If the input signal is RGB signal, additionally press the
AUTO SETUP button to adjust the position of the image.
6. Zoom the lens so the image fills the screen.
7. Readjust the focus.
8. Readjust the zoom so that the image size fits in the
screen.

POWER switch AC IN terminal


Q Adjusting focus, zoom and shift
4. Press the POWER ON button Pressing the LENS button changes the
The power indicator lamp illuminates in green and soon the Control buttons of the
setup screen in order of FOCUS, ZOOM
image is projected on the screen. projector
and SHIFT. Press F G I H to adjust.

Basic Operation
Press FOCUS, ZOOM or SHIFT button
POWER ON button Remote control buttons to display the setup screen. Press F G
I H to adjust.

INPUT SELECT buttons

NOTE: LENS button


If the projector is powered up at about 0 C (32 F), a warm-
up period of approximately 5 minutes may be necessary to
start projection. The temperature monitor (TEMP) lamp lights
up during the warm-up period. When the warm-up is CAUTION:
completed, the temperature monitor (TEMP) lamp turns off
Be careful not to catch your fingers between the lens and
and the image is projected on the screen.
shroud when shifting the lens.
If the temperature of the operating environment is low and
warm-up takes more than 5 minutes, the projector will judge NOTE:
that a problem has occurred and the power will be turned off The setup screen will be displayed with the optional fixed lens
automatically. If this happens, increase the temperature though, it will not be functioning.
around the projector so that it is 0 C (32 F) or higher, and Pressing F G I or H for 3 seconds or more, performance
then turn on the POWER switch and press the POWER ON the adjustment faster.
button again.

ENGLISH - 19
Projecting
J Switching off the projector J Lens home position
1. Press the POWER STANDBY button. 1. Press and hold the LENS button of the control button on
The confirmation screen will be displayed. the projector or SHIFT button of the remote control for
3 seconds or more.
POWER STANDBY button The HOME POSITION setup screen will be displayed for
5 seconds.
2. Press the ENTER button before the setup screen
disappeared.
While the lens returning to the home position, a message
PROGRESS appears on the screen.

NOTE:
The home position for the projection lens is the lens position
when the lens is being replaced or when the projector is being
stored away, and it is not the optical center of the screen.

J Adjustment range after lens


position (optical shift)
2. Select OK and press the ENTER button, or press the Do not move the lens beyond the bounds of the shift
POWER STANDBY button again. range as this may cause a change in the focus. This
The projection of the image stops, and the power indicator limitation is to protect the parts of the projector. Using the
of the projector lights up orange. The cooling fan keeps standard projection position as the reference, the optical
running. axis shift function makes it possible to adjust the
3. When the power indicator of the projector turns to red, projection position in the ranges shown in the figures
switch the POWER switch to OFF. below.
When the power indicator of the projector turns to red, the
Basic Operation

cooling fan stops.


While the cooling fan is still running, never turn off the
Q PT-DZ6710U/PT-DZ6700U/PT-D6000U
POWER switch, nor unplug the power cord from the wall
outlet. Standard projection position

NOTE:
In the cooling state after the power is turned off, the lamp will
not light up even if the power is turned on. To light up the lamp,
turn on the power supply again when the lamp has been
cooled sufficiently. Failure to observe this may shorten the
lamp life.

J Direct power off function


The power supplied internally causes the cooling fan to
continue operating and cool off in the event that the
power has failed or even after the power cord is
accidentally disconnected immediately after the power
has been turned off.
Q PT-DW6300U
NOTE:
When the lamp has been cooled by the direct power off Standard projection position
function, it sometimes takes longer than usual for the lamp to
light up again.
While the cooling fan is operating, do not place the projector
inside a box or bag.

ENGLISH - 20
Remote control operation
Shutter button Operating range
Auto setup button
You can operate the projector with the remote control within the
remote range 30 m (98'5"), approximately 30 horizontally
and 15 vertically.
Input select buttons Q Facing to the projector
Ensure the remote control emitter is facing to the remote
control signal receptor on front/back of the projector and
press the required buttons to operate.

Q Facing to the screen


On screen button Ensure the remote control emitter is facing to the screen
and press the required buttons to operate the projector.
Test pattern button The signal will be reflected off the screen. The operating
range may differ due to the screen material. This
function may not be effective with a translucent screen.

Status button NOTE:


Do not let strong light shine onto the signal receptor. The
remote control may malfunction under strong light such as
fluorescent.
If there are any obstacles between the remote control and the
Function button remote control signal receptor, the remote control may not
Aspect button operate correctly.

Basic Operation
Setting up the image position automatically
The automatic setup function can be used to automatically adjust the resolution, clock phase and picture position when
analogue RGB signals consisting of bitmap images such as computer signals are being input, or to automatically adjust
the picture position when DVI-D signals are being input.
1. Input an analogue RGB image signal.
2. Press the AUTO SETUP button.
3. Displays a message PROGRESS.
4. Displays a message COMPLETE when ended.
When the performance is not completed and ended, displays INCOMPLETE.

NOTE:
The automatic setup function does not work with video format signals such as signals output from a DVD player.
It is recommended to supply images with a bright white frame at the outermost periphery containing characters etc. that are clear in white
and black contrast when the system is in automatic adjustment mode.
Avoid supplying images that involve halftones or gradation such as photographs and computer graphics.
The clock phase adjustment may have been shifted even when the adjustment ended normally. In this case, manually adjust CLOCK
PHASE in POSITION menu.
If an image with blurred edges or a dark image is input, INCOMPLETE may appear or adjustment may not be performed properly even
if COMPLETE appears. In this case, manually adjust INPUT RESOLUTION in ADVANCED MENU, CLOCK PHASE and SHIFT in
POSITION menu.
For specific signals and landscape signals such as 16:9, see AUTO SETUP in DISPLAY OPTION menu of the functional instructions
that is in the provided CD-ROM.
Automatic adjustment may not be available depending on the machine type of the computer.
Automatic adjustment may not be available for synchronisation signal of C-SYNC and G-SYNC.
Image may be distorted for several seconds during automatic adjustment. This is not a malfunction.
For every supplied signal, adjustment is required.
Automatic adjustment can be cancelled by pressing the MENU button during the course of automatic adjustment.
Even for an RGB signal for which automatic setup is possible, if automatic setup is performed while moving images are being input,
INCOMPLETE may appear, or adjustment may not be performed properly even if COMPLETE appears.

ENGLISH - 21
Remote control operation

Switching the input signal


You can use the remote control to switch
RGB1 Switches to RGB 1 IN.
the signals that are being input and
projected. RGB2 Switches to RGB 2 IN.
DVI-D Switches to DVI-D IN.
VIDEO Switches to VIDEO IN.
S-VIDEO Switches to S-VIDEO IN.

SDI*1 Switches to SDI IN.

*1. SDI is only for PT-DZ6710U.

Stopping the projection


If the projector is not used for a certain period of time during the meeting intermission, for example, a shutter mode is
available that allows the user to hide images temporarily.
Press the SHUTTER button to block the projected light by the internal shutter, and press again to resume.

Clearing the screen


Press the ON SCREEN button to electronically mute the on-screen menus to avoid disrupting the program.
Press the ON SCREEN button again to displays

Changing the picture aspect ratio


Basic Operation

You can toggle through an appropriate set of aspect ratios for a given input signal. The setting will change each time the
ASPECT button is pressed.

Q Appearance sample
S-VIDEO signal
VID AUTO H S1 AUTO H VID AUTO(PRI.) H THROUGH H 16:9 H 4:3 H H-FIT H V-FIT H HV-FIT H VID AUTO

NOTE:
The appearance of setting options vary according to input signals. See ASPECT in POSITION menu of the functional instructions that is
in the provided CD-ROM.

Displaying the internal test pattern


The projector has 7 types of internal test patterns to check the condition of the set.

1. Display an input signal image.


2. Press the TEST PATTERN button.
3. Press I H to select the required test pattern.

NOTE:
See TEST PATTERN menu of the functional instructions that is in the provided CD-ROM.

ENGLISH - 22
Remote control operation

Using an assigned function


You can assign a selected function to the FUNCTION button. Following functions are assignable.

Options Functions
NOTE:
DISABLE Deactivate the FUNCTION button. See FUNCTION in PROJECTOR SETUP menu and each
SUB MEMORY LIST Display the assigned SUB MEMORY LIST. corresponding menu items of the functional instructions that is
SYSTEM SELECTOR Switches the SYSTEM SELECTOR options. in the provided CD-ROM.
SYSTEM DAYLIGHT Switches the SYSTEM DAYLIGHT VIEW
VIEW setting.
FREEZE Freezes the image.
SIDE BY SIDE Start the SIDE BY SIDE mode.

Displaying the status of the projector


Pressing this button displays several pages of projector status information.

NOTE:
See STATUS in PROJECTOR SETUP menu and Accessing with the web browser in Technical Information of the functional instructions
that is in the provided CD-ROM.

Resetting to the factory default

Basic Operation
If an adjustment item is selected and press the DEFAULT button, the adjustment value will return to the factory default
setting.

ENGLISH - 23
Menu Navigation
Main menu and Sub-menu
The menu options are structured and categorized. You can CLOCK PHASE
navigate through the menu with F G I H buttons. See
(Default: 16)
Navigating through the menu on page 27.
Some default settings vary by the selected input signal. GEOMETRY
Sub-menu items vary according to the selected input signal. (PT-DZ6710U only)
Some settings are adjustable without any signals. OFF KEYSTONE
See the functional indications in the CD-ROM that is CURVED PC
provided with the projector.
GEOMETRY:KEYSTONE
VERTICAL KEYSTONE
VERTICAL SUB KEYSTONE
PICTURE HORIZONTAL KEYSTONE
HORIZONTAL SUB KEYSTONE
LINEARITY
PICTURE MODE
STANDARD CINEMA GEOMETRY:CURVED
NATURAL DYNAMIC LENS THROW RATIO
GRAPHIC VERTICAL KEYSTONE
HORIZONTAL KEYSTONE
CONTRAST VERTICAL ARC
(Default: 0) HORIZONTAL ARC
BRIGHTNESS VERTICAL BALANCE
HORIZONTAL BALANCE
(Default: 0)
COLOR KEYSTONE
(PT-DZ6700U/PT-DW6300U/PT-D6000U
(Default: 0)
only)
TINT VERTICAL KEYSTONE
(Default: 0) VERTICAL SUB KEYSTONE
LINEARITY
COLOR TEMPERATURE
Settings

DEFAULT USER
MIDDLE HIGH
WHITE GAIN ADVANCED MENU
(Default: 10)
DIGITAL CINEMA REALITY
SYSTEM DAYLIGHT VIEW AUTO OFF
OFF 1 25p FIXED 30p FIXED
2 3
BLANKING
SHARPNESS UPPER LOWER
(Default: 6) LEFT RIGHT
NOISE REDUCTION INPUT RESOLUTION
1 2 TOTAL DOTS DISPLAY DOTS
3 OFF TOTAL LINES DISPLAY LINES
AI CLAMP POSITION
ON OFF
EDGE BLENDING
SYSTEM SELECTOR OFF ON
AUTO NTSC NTSC 4.43 PAL
GAMMA
PAL-M PAL-N SECAM PAL60
2.2 1.8 2
RGB YCBCR VGA60 480p
480pRGB YPBPR 108060i 103560i BRIGHT ADJUST
72060p 108024p 108050i 108030p BRIGHT INSIDE BRIGHT OUTSIDE
108025p 108024sF 72050p 480i OUTSIDE AREA
576i RASTER POSITION
VERTICAL HORIZON

POSITION
DISPLAY LANGUAGE
SHIFT
ASPECT
DEFAULT VID AUTO S1 AUTO
VID AUTO(PRI.) THROUGH
16:9 4:3 H-FIT
V-FIT HV-FIT
ZOOM
INTERNAL FULL

ENGLISH - 24
Menu Navigation
INSTALLATION
DISPLAY OPTION FRONT/FLOOR FRONT/CEILING
REAR/FLOOR REAR/CEILING
COLOR MATCHING HIGH ALTITUDE MODE
OFF 3 COLORS OFF ON
7 COLORS MEASURED
COOLING CONDITION
COLOR CORRECTION FLOOR SETTING
OFF USER VERTICAL DOWN SETTING
CONTRAST MODE CEILING SETTING
NORMAL HIGH VERTICAL UP SETTING

SCREEN SETTING LAMP SELECT


DUAL SINGLE
SCREEN FORMAT LAMP1 LAMP2
16:10 16:9 4:3
LAMP RELAY
SCREEN POSITION OFF 00:00 - 23:00
AUTO SIGNAL LAMP POWER
ON OFF HIGH LOW
AUTO SETUP STANDBY MODE
DEFAULT WIDE NORMAL ECO
USER
RS-232C
DVI-D IN (IN) BAUDRATE
DVI EDID (IN) PARITY
(OUT) BAUDRATE
EDID3 EDID1 EDID2(PC)
(OUT) PARITY
DVI SIGNAL LEVEL RESPONSE(ID ALL)
0-255:PC 16-235 GROUP
SDI IN RESPONSE(ID GROUP)
64-940 4-1019 REMOTE2 MODE

Settings
DEFAULT USER
ON-SCREEN DISPLAY
OSD POSITION
STATUS
1 2 3 FILTER COUNTER RESET
4 5 6
7 8 9
NO SIGNAL SHUT-OFF
DISABLE
OSD DESIGN 15 MIN. 20 MIN. 25 MIN. 30 MIN.
1 2 3 35 MIN. 40 MIN. 45 MIN. 50 MIN.
4 5 6 55 MIN. 60 MIN.
OSD MEMORY FUNCTION BUTTON
ON OFF DISABLE
INPUT GUIDE SUB MEMORY LIST
ON OFF SYSTEM SELECTOR
SYSTEM DAYLIGHT VIEW
WARNING MESSAGE FREEZE
ON OFF SIDE BY SIDE
BACK COLOR DAY AND TIME
BLACK BLUE TIME ZONE ADJUST CLOCK
LOGO1 LOGO2
SAVE ALL USER DATA
STARTUP LOGO LOAD ALL USER DATA
LOGO2 NONE
LOGO1 INITIALIZE
FREEZE SERVICE PASSWORD
SIDE BY SIDE
VIDEO S-VIDEO
RGB1 RGB2 TEST PATTERN
DVI-D SDI
OFF
TEST PATTERN

PROJECTOR SETUP SIGNAL LIST


PROJECTOR ID REGISTERED SIGNAL STATUS
ALL 1 - 64
SUB MEMORY LIST

ENGLISH - 25
Menu Navigation

SECURITY NETWORK
SECURITY PASSWORD NETWORK SETUP
OFF ON
HOST NAME DHCP
SECURITY PASSWORD CHANGE IP ADDRESS SUBNET MASK
DISPLAY SETTING DEFAULT GATEWAY STORE
OFF TEXT NETWORK CONTROL
LOGO1 LOGO2 WEB CONTROL
TEXT CHANGE PJLink CONTROL
COMMAND CONTROL
MENU LOCK COMMAND PORT
OFF ON STORE
MENU LOCK PASSWORD NETWORK STATUS
CONTROL DEVICE SETUP DHCP IP ADDRESS
SUBNET MASK DEFAULT GATEWAY
CONTROL PANEL DNS1 DNS2
ENABLE DISABLE MAC ADDRESS
REMOTE CONTROLLER
ENABLE DISABLE
Settings

ENGLISH - 26
Menu Navigation

Navigating through the menu


J Displaying the Main menu J Operating procedure
Press the MENU button to display the main menu. 1. Press F G to scroll to the required main menu item and
press the ENTER button to select.
MAIN MENU
The selected item is highlighted in orange and the sub-
PICTURE
menu is displayed.
POSITION
See Main menu and Sub-menu on page 24.
ADVANCED MENU
DISPLAY LANGUAGE MAIN MENU

DISPLAY OPTION PICTURE


PROJECTOR SETUP POSITION
TEST PATTERN ADVANCED MENU
SIGNAL LIST DISPLAY LANGUAGE
SECURITY DISPLAY OPTION
NETWORK PROJECTOR SETUP
TEST PATTERN
SIGNAL LIST
MENU SELECT
SECURITY
ENTER SUB MENU
NETWORK

J Adjusting with the bar scale MENU SELECT

items ENTER SUB MENU

The triangle mark under the bar indicates factory 2. Press F G to scroll to the required sub-menu item and
default setting and the square indicates the current press I H or the ENTER button to adjust.
setting. The selected item is called up and the other menu items
disappear from the screen. Called up item will be disappear
Current setting after 5 seconds and return to the menu mode.
If there is a lower level, the next level will be displayed.

Settings
CONTRAST 0
POSITION
ADJUST SHIFT
ASPECT AUTO
Default ZOOM
CLOCK PHASE 0
J Returning to the previous menu GEOMETRY KEYSTONE

Press the MENU button to return to the previous menu. Press


repeatedly to escape from the menu mode and return to the
projection.

MENU SELECT
ENTER CHANGE

3. Press I H to adjust or set the selected item.


For items using a bar scale, the current settings are
displayed on the left of the bar scale.
You can cycle through the options of an item by pressing I
H.
CONTRAST 0

ADJUST

4. Press the MENU button to return to the previous menu.

ENGLISH - 27
Monitor Lamp indicators
Managing the indicated problems

Indicators
Power indicator
Lamp1 (LAMP1) indicator
Lamp2 (LAMP2) indicator
Temperature (TEMP) indicator
Filter (FILTER) indicator
STANDBY(RED)/ LAMP TEMP FILTER
ON(GREEN)

STANDBY(RED)/ LAMP TEMP FILTER


ON(GREEN)

If a problem should occur with the projector, the indicators will inform you. Manage the indicated problems as follow.
1. Confirm the status of all indicators and projector, and switch off the projector in proper way.
2. Find out the cause of the problem by status of each indicator.
3. Follow the instruction for each indication below and solve the problem.
4. Turn on the projector in the correct way and confirm the indicator is not indicating a problem any longer.

NOTE:
If no problem is found or the problem remains, do not turn on the projector. Instead contact an Authorized Service Center.

J LAMP1/LAMP2 indicator
Lamp
Information Check point Remedial measure
indication
Did you notice a REPLACE This lamp monitor lights up when the lamp
Indicates the time for LAMP message on the screen unit used hours have reached 1 800 hours.
Lighting in red
replacing the lamp unit when turning on the projector Request the dealer to replace the lamp unit.
power supply?
Check the lamp unit Install the lamp unit.
Blinking in red
Lamp unit is not installed. compartment. When lamp unit is installed and still having
once
the indicator lights, contact to the dealer.
Did you turn the power back on Wait until the lamp has cooled off, and then
immediately after turning it off? turn on the power.
Blinking in red Error is detected in the Some error has arisen in the Turn off the POWER switch of the projector
3 times lamp circuit. lamp circuit. in proper way and contact the dealer.
Check for fluctuation (or drop) in
the source voltage.

J TEMP indicator
Lamp
Information Check point Remedial measure
indication
Maintenance

Did you turn on the power when Wait about 5 minutes in the current status.
the ambient temperature was Install the unit in a location having an
Warm-up status
lower than approx. 0 C (32 F)? ambient temperature from 0 C (32 F) -
Lighting in red
45 C (113 F).
High temperature inside. Check the ventilation port is Remove the object that is blocking the
(WARNING) blocked. ventilation port.
Is the room air temperature too Move the projector to a temperature of 0 C
high? (32 F) - 45 C (113 F) and the humidity of
Blinking in red High temperature inside.
Was the temperature warning 20 % to 80 % (no condensation).
twice (Standby condition)
indication displayed? Turn off the POWER switch of the projector
in proper way and contact the dealer.
Blinking in red Cooling fan has been Turn off the POWER switch of the projector
3 times stopped. in proper way and contact the dealer.

ENGLISH - 28
Monitor Lamp indicators
J FILTER indicator
The FILTER indicates the Auto Cleaning Filter (ACF) unit status.
Lamp
Information Check point Remedial measure
indication
Check the REMAINING FILTER Replace the ACF unit.
Lighting in red The ACF unit has run out. of STATUS in PROJECTOR
SETUP menu.
The ACF unit is not Check the ACF unit Replace the ACF unit.
Blinking in red compartment.
installed.*1
The ACF unit remains Check the REMAINING FILTER Request the dealer to purchase the new
few. The remaining use of STATUS in PROJECTOR ACF unit.
Lighting in time of the ACF unit is SETUP menu.
orange approximately
200 hours.*2
Is foreign object blocking the Remove the foreign object from the ACF
Blinking in The ACF unit cannot ACF unit operation? unit.
orange operate properly. When the foreign object still remained,
contact the dealer.
*1. When the ACF unit is not installed, displays THE AIR FILTER HAS NOT BEEN INSTALLED PROPERLY. message and power off
with the indicator blinking in red.
*2. 200 hours is the roughly guided time.

NOTE:
When the FILTER indicator is flashing green, the Auto Cleaning Filter (ACF) is normally rolling up.
When the ACF unit is operating, operational sound may be heard.
In a dusty environment, the guided remaining use time will be shorter. Contact the dealer to purchase the new ACF unit earlier.
If using the projector at high elevations 1 400 - 2 700 m (4 593 - 8 858 ft) sea level and HIGH ALTITUDE MODE in PROJECTOR SETUP
menu is OFF, it may cause malfunction of the ACF unit.

Maintenance

ENGLISH - 29
Replacement
Replacing the Lamp unit
J Before replacing the Lamp unit
Turn off the POWER switch of the projector in proper way and disconnect the power plug from the wall outlet.
Wait for more than 1 hour and make sure the lamp unit and the surroundings are cooled enough.
Prepare a Phillips-head screwdriver.
Contact the dealer to purchase a replacement lamp unit (ET-LAD60:1 bulb unit, ET-LAD60W: 2 bulb units).
When the projector is mounted on the ceiling, do not work directly under the projector or put your face
closer to the projector.

CAUTION:
The lamp may explode or shorten the lamp life by shocks or chipping damage.
NOTE:
Prior to replacing the lamp unit, allow it to cool down to prevent the risk of burns, damage and other hazards.
Do not attempt replacement with an unauthorized lamp unit.

J When to replace the lamp unit


The lamp unit is consumable and the brightness decreases by duration of usage. The LAMP1/LAMP2
indicators will inform you of the replacement timing at 1 800 hours, and at 2 000 hours, the projector will be
turned off. Those figures are rough guidance and might be shortened by the usage conditions, characteristics
of the lamp unit, environmental conditions, and so on. You can check the duration of usage time using LAMP1/
LAMP2 of STATUS in the PROJECTOR SETUP menu.

On screen LAMP indicator

REPLACE LAMP
Indication

LAMP
REPLACE LAMP is displayed on the upper left
Over 1 800 hours of the screen for 10 minutes. Press any button to
clear the screen, or disappears after 10 minutes.
Lights in red
REPLACE LAMP is displayed on the upper left
Over 2 000 hours of the screen, and it will stay until you respond.
To clear the screen, press any button.

CAUTION:
If you keep using the lamp unit after 2 000 hours, it cause the damage of the projector. Automatically the projector will be powered off
after 10 minutes.
NOTE:
The guide times, 1 800 and 2 000 hours, are rough estimates based on certain conditions and are not a guaranteed time.
For more information about the lamp unit, such as guaranteed time, see the instructions which is provided with the lamp unit.
Maintenance

ENGLISH - 30
Replacement
J Replacement procedure
Q Removing and replacing the lamp unit
1. Use a Phillips-head screwdriver to loosen the 1 4. Hold the handle of the new lamp unit and replace it
lamp unit cover fixing screw on the back of the in correct direction.
projector until the screws turn freely, and remove 5. Press in the lamp unit until it clicks and make sure
the lamp unit cover. the unit is installed securely.
Slide the lamp unit cover to the buttons and pull to 6. Tighten the 3 lamp unit fixing screws securely with
remove. a Phillips-head screwdriver.

Lamp unit cover


fixing screw

Fan electric power


connector

Lamp unit cover

2. Use a Phillips-head screwdriver to remove the


3 lamp unit fixing screws.
3. Hold the handles of the lamp unit and pull the used 7. Attach the lamp unit cover and tighten the 1 lamp
lamp unit gently from the projector. unit cover fixing screw securely with a Phillips-
Lamp unit screws Handle head screwdriver.
Slide the lamp unit cover to the hinge side and push
in to attach securely.
Make sure the fan electric power connector of the
lamp unit cover is inserted securely to the projectors
connector.

Handle Lamp unit screws

Replacing the Auto Cleaning Filter (ACF)


J Before replacing the ACF
Wait until the cooling fan stops and turn off the POWER switch of the projector in proper way.
Maintenance

Disconnect the power cord from the wall outlet.


Contact an Authorized Service Center to purchase a replacement ACF (ET-ACF100).

J When to replace the ACF


The ACF unit is consumable product and effects on ventilation. The FILTER indicator will inform you of the
replacement timing. You can check the remaining amount of the ACF unit in REMAINING FILTER of STATUS
in PROJECTOR SETUP menu.

ENGLISH - 31
Replacement
J Replacement procedure
1. Loosen 1 ACF cover fixing screw until the screws J Resetting the REMAINING
turn freely and remove the ACF cover.
FILTER
1. Turn on the projector and display the FILTER
COUNTER RESET in PROJECTOR SETUP
menu.
2. Press the ENTER button.
The confirmation screen will be displayed.
3. Select OK by pressing I, then press the ENTER
button.
4. Display the STATUS in PROJECTOR SETUP
menu and confirm the REMAINING FILTER.

NOTE:
ACF cover fixing screw See FILTER COUNTER RESET and STATUS in
ACF cover PROJECTOR SETUP menu of the functional instructions that
is in the provided CD-ROM.
2. Slide out the ACF unit from the projector slowly.
When you replace the ACF unit, clean the
compartment and/or the air exhaust port if you need
to.
3. Insert the new ACF unit into the compartment in
correct direction and slightly push until it clicks.

ACF unit

4. Attach the ACF cover and tighten 1 ACF cover


fixing screw securely.

NOTE:
If the ACF and/or ACF cover are attached incorrectly, the
projector may not be turned on.
Do not switch the power on while the ACF cover removed.
The replacement timing of the ACF is 36 000 hours of use at
maximum and it depends on environment of usage.
Maintenance

ENGLISH - 32
Troubleshooting
Should any problem persist, contact your dealer.

Reference
Problem Cause
page*1
The power cord may not be connected. 18
The POWER switch is turned off. 20
No electric supply is at the wall outlet. 20
Power does not turn on. TEMP indicator is lit or flashes. 28
LAMP1/LAMP2 indicator is lit or flashes. 28
The lamp unit cover has not been securely installed. 31
The circuit breakers have tripped. -
The video signal input source may not be connected to a terminal CD-ROM
properly.
The input selection setting may not be correct. 22
No picture appears. The BRIGHTNESS adjustment setting may be at the minimum setting. CD-ROM
The input source which is connected to the projector may have a
problem.
The shutter function may be in use. 22
The lens focus may not have been set correctly. 19
The projector may not be at the correct distance from the screen. CD-ROM
The picture is fuzzy.
The lens may be dirty. -
The projector may be tilted too much. CD-ROM
COLOR or TINT adjustment may be incorrect. CD-ROM
The input source which is connected to the projector may not be -
The color is pale or grayish.
adjusted correctly.
RGB cable is damaged. -
CONTROL PANEL of CONTROL DEVICE SETUP in SECURITY
The control buttons of the menu is disabled. If you have a loss of the remote control while the
CD-ROM
projector do not operate. CONTROL PANEL is disabled, press and hold the MENU button for
2 seconds with pressing the ENTER button.

REMOTE CONTROLLER of CONTROL DEVICE SETUP in CD-ROM


SECURITY menu is disabled.
The batteries may be weak. -
The batteries may not have been inserted correctly. 14
The remote control does
The remote control signal receptor on the projector may be 21
not operate.
obstructed.
The remote control unit may be out of the operation range. 21
Strong light such as fluorescent shine onto the signal receptor. -
The remote control ID setting is incorrect. CD-ROM
The color format may not have been set correctly. CD-ROM
The picture does not
There may be a problem with the VCR or other signal source. -
display correctly. A signal which is not compatible with the projector is being input. 34
The cable may be longer than the optional cable. -
The external video output from a laptop computer may not be correct. -
Picture from a computer (You may be able to change the external output settings by pressing
Maintenance

does not appear. the [Fn] + [F3] or [Fn] + [F10] keys simultaneously. The actual method
varies depending on the type of computer; refer to the documentation
provided with your computer for further details.)
The graphic board driver of the computer needs to be updated to the -
Picture from a computer latest version.
DVI-D graphic board does DVI-D IN setting in DISPLAY OPTION menu may be incorrect setting. CD-ROM
not appear. The computer may need to be restarted after switching DVI-D IN -
setting in DISPLAY OPTION menu of the projector correctly.
*1. CD-ROM: See the functional instructions in the provided CD-ROM.

ENGLISH - 33
Technical Information
List of compatible signals
Scanning Dot clock
Display frequency frequency PnP*3
Picture
Mode resolution Format*4
quality*2 DVI-D DVI-D
(dots)*1 H (kHz) V (Hz) (MHz) RGB2
EIDI1 EIDI2
NTSC/NTSC 4.43/
720 x 480i 15.7 59.9 - A
PAL-M/PAL60 V/S
PAL/PAL-N/SECAM 720 x 576i 15.6 50.0 - A
525i (480i) 720 x 480i 15.7 59.9 13.5 A
R/Y
625i (576i) 720 x 576i 15.6 50.0 13.5 A
525p (480p) 720 x 483 31.5 59.9 27.0 A D
625p (576p) 720 x 576 31.3 50.0 27.0 A D
1 125 (1 080)/60i 33.8 60.0 74.3 AA*5 D
1 920 x 1 080i
1 125 (1 080)/50i 28.1 50.0 74.3 AA*5 D
1 125 (1 080)/24p 1 920 x 1 080 27.0 24.0 74.3 AA*5 D
1 125 (1 080)/24sF 1 920 x 1 080i 27.0 24.0 74.3 AA*5
D/R/Y
1 125 (1 080)/25p 28.1 25.0 74.3 AA*5 D
1 920 x 1 080
1 125 (1 080)/30p 33.8 30.0 74.3 AA*5
1 125 (1 080)/60p 67.5 60.0 148.5 AA*5 D
1 920 x 1 080p
1 125 (1 080)/50p 56.3 50.0 148.5 AA*5 D
750 (720)/60p 45.0 60.0 74.3 AA*6 D
1 280 x 720
750 (720)/50p 37.5 50.0 74.3 AA*6 D
31.5 70.1 25.2 A
VGA400 640 x 400
37.9 85.1 31.5 A
31.5 59.9 25.2 A D D D
35.0 66.7 30.2 A
VGA480 640 x 480 37.9 72.8 31.5 A D D
37.5 75.0 31.5 A D D
43.3 85.0 36.0 A
35.2 56.3 36.0 A D D
37.9 60.3 40.0 A D D
SVGA 800 x 600 48.1 72.2 50.0 A D D
46.9 75.0 56.3 A D D
53.7 85.1 56.3 A
MAC16 832 x 624 49.7 74.6 57.3 A D D
39.6 50.0 51.9 *7
AA
48.4 60.0 65.0 AA*7 D D
56.5 70.1 75.0 AA*7 D D
60.0 75.0 78.8 AA*7 D D D/R
XGA 1 024 x 768
65.5 81.6 86.0 AA*7
68.7 85.0 94.5 AA*7
80.0 100.0 105.0 AA*7
96.7 120.0 130.0 AA*7
64.0 71.2 94.2 A
MXGA 1 152 x 864 67.5 74.9 108.0 A
76.7 85.0 121.5 A
MAC21 1 152 x 870 68.7 75.1 100.0 A D D
39.6 49.9 65.3 AA*6
1 280 x 768 1 280 x 960
47.8 59.9 79.5 AA*6
41.3 50.0 68.0 AA*6
1 280 x 800 1 280 x 800
49.7 59.8 83.5 AA*6
MSXGA 1 280 x 960 60.0 60.0 108.0 A
Appendix

64.0 60.0 108.0 A D D


SXGA 1 280 x 1 024 80.0 75.0 135.0 A D D
91.1 85.0 157.5 A*8 D/R*9
65.2 60.0 122.6 A D D D/R
SXGA+ 1 400 x 1 050
82.2 75.0 155.9 A*8 D/R*9
WXGA+ 1 440 x 900 55.9 59.9 106.5 A D/R
UXGA 1 600 x 1 200 75.0 60.0 162.0 A*8 D D D/R*9

ENGLISH - 34
Technical Information
Scanning Dot clock
Display frequency frequency PnP*3
Picture
Mode resolution Format*4
quality*2 DVI-D DVI-D
(dots)*1 H (kHz) V (Hz) (MHz) RGB2
EIDI1 EIDI2
WSXGA+ 1 680 x 1 050 65.3 60.0 146.3 A
1 920 x 1 080*10 1 920 x 1 080 66.6 59.9 138.5 AA*5 D/R
WUXGA 1 920 x 1 200 74.0 60.0 154.0 AA*5 D D
*1. The i appearing after the resolution indicates an interlaced signal.
*2. The following symbols are used to indicate picture quality.
AA Maximum picture quality can be obtained.
A Signals are converted by the image processing circuit before picture is projected.
B Some loss of data occurs to make projection easier.
*3. Marked signals are indicated in
*4. The following symbols are used to indicate the format.
V = VIDEO, S = S-VIDEO, D = DVI, R = RGB, Y = YPBPR
*5. PT-DW6300U/PT-D6000U: A
*6. PT-DZ6710U/PT-DZ6700U/PT-D6000U: A
*7. PT-DZ6710U/PT-DZ6700U/PT-DW6300U: A
*8. PT-DW6300U/PT-D6000U: B
*9. RGB signals only and DVI-D is not compatible.
*10.VESA CVT-RB (Reduced Blanking) compatible.

NOTE:
Projecting an interlaced signal may cause flicker in screen.

J Display dots of each model


PT-DZ6710U 1 920 x 1 200

PT-DZ6700U 1 920 x 1 200

PT-DW6300U 1 280 x 800

PT-D6000U 1 024 x 768

Appendix

ENGLISH - 35
Technical Information

Specifications
Power supply AC 120 V 60 Hz
PT-DZ6710U/PT-DZ6700U: 820 W
Power consumption PT-DW6300U/PT-D6000U: 780 W
During standby (when fan is stopped): Approx. 8 W*1
PT-DZ6710U/PT-DZ6700U: 8 A
Amps
PT-DW6300U/PT-D6000U: 7.2 A
Panel size PT-DZ6710U/PT-DZ6700U: 0.67 type PT-DW6300U: 0.65 type
(diagonal) PT-D6000U: 0.7 type
PT-DZ6710U/PT-DZ6700U/PT-DW6300U: 16 : 10
Aspect ratio
PT-D6000U: 4:3
DLP chip
Display method 1 unit DLP chip, DLP type
PT-DZ6710U/PT-DZ6700U: 2 304 000 (1 920 x 1200)
Pixels PT-DW6300U: 1 024 000 (1 280 x 800)
PT-D6000U: 786 432 (1 024 x 768)
Motorized zoom 1.8 - 2.4:1 Lens is optional for the projectors that L
follows in model number.
Lens F 1.7 - 2.0, f 25.6 mm - 33.8 mm
Motorized focus PT-DZ6710U/PT-DZ6700U: f = 26.8 - 35.7
PT-DW6300U/PT-D6000U: f = 25.6 - 33.8
Lamp UHM lamp (300 W) x 2
PT-DZ6710U/PT-DZ6700U/ Lens is optional for the projectors that L
PT-DW6300U:6 000 lm (ANSI) follows in model number.
Luminosity*2 PT-D6000U: 6 500 lm (ANSI)
Average value of the lens that is provided with the
projector.
Temperature: 0 C - 45 C (32 F - 113 F)
Operating environment
Humidity: 20% - 80% (no condensation)
VIDEO/S-VIDEO H: 15.75 kHz/15.63 kHz, V: 50 Hz/60 Hz
H: 15 - 91 kHz, V: 50 - 85 Hz Panasonic Intelligent Auto Scanning (PIAS)
RGB Dot clock frequency
PT-DZ6710U/PT-DZ6700U: 162 MHz or less
PT-DW6300U/PT-D6000U: 150 MHz or less
480p, 576p, 720/60p, 720/59.94p, 720/50p, 1 080/60p, 1 080/59.94p,1 080/50p, 1 080/60i,
1 080/59.94i, 1 080/50i, 1 080/24sF, 1 080/23.98sF, 1 080/30p, 1 080/29.97p, 1 080/25p,
1 080/24p, 1 080/23.98p
DVI-D
Displayable resolution: VGA - WUXGA (non interlace)
Scanning
Dot clock frequency: 25 - 162 MHz
frequency*3 WUXGA signal is applicable with VESA CVT-RB (Reduced Blanking).
480i H: 15.73 kHz, V: 59.94 Hz 576i H: 15.63 kHz, V: 50 Hz
480p H: 31.5 kHz, V: 59.94 Hz 576p H: 31.25 kHz, V: 50 Hz
720/50p H: 37.5 kHz, V: 50 Hz 720/60p H: 45 kHz, V: 60 Hz
1 035/60i H: 33.75 kHz, V: 60 Hz 1 080/50i H: 28.13 kHz, V: 50 Hz
YPBPR 1 080/60i H: 33.75 kHz, V: 60 Hz 1 080/24p H: 27 kHz, V: 24 Hz
1 080/25p H: 28.13 kHz, V: 25 Hz 1 080/30p H: 33.75 kHz, V: 30 Hz
1 080/24sF H: 27 kHz, V: 48 Hz 1 080/50p H: 56.25 kHz, V: 50 Hz
1 080/60p H: 67.5 kHz, V: 60 Hz
HD/SYNC, VD terminals are not compliant with 3 value composite SYNC.
Color system 7 (NTSC/NTSC 4.43/PAL/PAL-M/PAL-N/PAL60/SECAM)

Projection size 50" - 600" (1 270 mm - 12 700 mm)


PT-DZ6710U/PT-DZ6700U/PT-DW6300U: 16 : 10
Screen aspect ratio
PT-D6000U: 4:3
FRONT/FLOOR, FRONT/CEILING, REAR/FLOOR, REAR/CEILING
Installation
(Menu selection method)
Appendix

Contrast ratio 2 000 : 1 (When CONTRAST MODE in DISPLAY OPTION menu is set to HIGH)

ENGLISH - 36
Technical Information
1 set, Mini DIN 4p
S-VIDEO IN
Y: 1.0 V [p-p], C: 0.286 V [p-p], 75 , compatible with S1 signal
1 set, BNC pin jack
VIDEO IN
1.0 V [p-p], 75
1 set, BNC x 5
RGB signal
0.7 V [p-p], 75
G-SYNC: 1.0 V [p-p], 75
RGB 1 IN HD/SYNC: TTL high impedance, automatic positive/negative polarity compatible
VD: TTL high impedance, automatic positive/negative polarity compatible
YPBPR signal
Y: 1.0 V [p-p] Synchronisation signal included
PBPR: 0.7 V [p-p], 75
1 set of high density, D-sub 15p (female)
RGB signal
Terminals 0.7 V [p-p], 75 (G-SYNC: 1.0 V [p-p], 75 )
HD/SYNC: TTL high impedance, automatic positive/negative polarity compatible
RGB 2 IN
VD: TTL high impedance, automatic positive/negative polarity compatible
YPBPR signal
Y: 1.0 V [p-p] Synchronisation signal included
PBPR: 0.7 V [p-p], 75
DVI-D IN 1 set, DVI-D 24-pin (Single link), DVI 1.0 compatible, HDCP compatible

SERIAL 1 set, D-sub 9-pin (female), RS-232C compatible, computer control use
REMOTE1 1 set, M3 pin jack, wired remote control use, multiple connection use

REMOTE2 1 set, D-sub 9-pin, external control use


1 set, RJ-45, network connection use, PJLink compatible,
LAN
10 Base-T/100Base-TX
1 set, BNC pin jack SMPTE292M: 720/50p, 720/60p, 1 035/60i,
SDI SD-SDI (Y, CB, CR, 4:2:2) 1 080/50i, 1 080/60i, 1 080/25p, 1 080/24p,
SMPTE259M: 480i, 576i 1 080/24sF, 1 080/30p
Cabinet Moulded plastic

Power cord length 3.0 m (9'10")


Width 498 mm (19- 19/32")
Dimensions Height 175 mm (6 - 7/8")
Length 448 mm (17 - 5/8")
Weight Approx. 16 kg (35.3 lbs.)*4
Power supply 3 V DC (AA battery x 2)

Operating range Approx. 30 m (98'5") (when operated directly in front of signal receptor)

Remote Weight 120 g (4.2 ozs.) (including batteries)


control Width 51 mm (2')
Length 176 mm (6 - 29/32")
Dimensions
22.7 mm (-7/8") (not including surface projection
Height
parts)
Ceiling bracket ET-PKD56H (High ceiling), ET-PKD55S (Low ceiling)
Projection lens ET-DLE150, ET-DLE250, ET-DLE350, ET-DLE450, ET-DLE055
Options
Lamp unit ET-LAD60 (1 bulb), ET-LAD60W (2 bulbs)

ACF unit ET-ACF100

*1. When STANDBY MODE in PROJECTOR SETUP menu is NORMAL: Approx. 8 W


When STANDBY MODE in PROJECTOR SETUP menu is ECO: Approx. 0.2 W
*2. Measurement, measuring conditions and method of notation all comply with ISO21118 international standards.
*3. See List of compatible signals on page 34 for available signals.
*4. Average value. Each product has an individual variable in weight.
Appendix

ENGLISH - 37
Technical Information

Dimensions

Unit: mm (inch)

(16-5/8'')
423
(3-1/32'') (6-3/32'') (-21/32'') (-11/32'')
9
498

16.8
(19-19/32'')

155
77.5

(-13/16'')
21
(-3/16'')
5

(-25/32'')
20

Trademark acknowledgements
VGA and XGA are trademarks of International Business Machines Corporation.
S-VGA is a registered trademark of the Video Electronics Standards Association.
The font used in the on-screen displays is a Ricoh bitmap font, which is manufactured and sold by Ricoh
Company, Ltd.
All other trademarks are the property of the various trademark owners.
Appendix

ENGLISH - 38
Index
A L
Accessories .................................................................... 11 LAMP
Air exhaust port ............................................................... 12 Indicator status ........................................................... 28
Air intake port .................................................................. 13 Lamp unit compartment ............................................... 12
ASPECT LAMP1/LAMP2 indicators ............................................ 12
Remote control button ................................................. 14 Replacing .................................................................. 30
Remote control function ............................................... 22 LAN
Auto Cleaning Filter (ACF) .............................................. 13 Terminal .................................................................... 13
AUTO SETUP LENS
Control panel button .................................................... 12 Control panel button ....................................................
12
Remote control button ................................................. 14 Projection lens ............................................................
12
Remote control function ............................................... 21 Projector lens cover ....................................................
11
Remote control button .................................................
14
B Lens home position ........................................................ 20
Battery ............................................................................ 11 M
Compartment .............................................................. 14
Burglar hook port ............................................................ 12 Mains lead
AC IN terminal ............................................................ 13
C Accessories ............................................................... 11
Connecting ................................................................ 18
CD-ROM ......................................................................... 11
MENU
Accessories ................................................................ 11
CD-ROM ................................................................... 24
Menu ......................................................................... 24
Control panel button .................................................... 12
D Navigation ................................................................. 27
Remote control button ................................................. 14
DEFAULT Structure .................................................................... 24
Remote control button ................................................. 14
Remote control function ............................................... 23 N
Dimensions ..................................................................... 38 Navigation buttons
Direct power off ............................................................... 20 Control panel .............................................................. 12
DISPLAY LANGUAGE .................................................... 24 Navigation ................................................................. 27
DVI-D Remote control buttons ............................................... 14
Control panel button .................................................... 12 Numeric (0 - 9) buttons
Remote control button ................................................. 14 Remote control buttons ............................................... 14
Terminal .................................................................... 13
O
E
ON SCREEN
ENTER Remote control button ................................................. 14
Control panel button .................................................... 12 Remote control function ............................................... 22
Menu navigation ......................................................... 27
Remote control button ................................................. 14 P
F POWER
Switch ....................................................................... 13
FILTER Switching on/off .......................................................... 19
Compartment .............................................................. 13 Power cord secure lock
Indicator ..................................................................... 12 Accessories ............................................................... 11
Indicator status ........................................................... 29 Attaching ................................................................... 18
Replacing ................................................................... 31 POWER ON
FOCUS Control panel button .................................................... 12
Adjusting .................................................................... 19 Remote control button ................................................. 14
Remote control button ................................................. 14 Switching on/off .......................................................... 19
Focus ring ....................................................................... 12 POWER STANDBY
Front leg adjusters .......................................................... 12 Control panel button .................................................... 12
FUNCTION Remote control button ................................................. 14
Remote control button ................................................. 14 Projector lens cover
Remote control function ............................................... 23 Accessories ............................................................... 11
I R
ID Remote control ............................................................... 14
Remote control button ................................................. 14 Accessories ............................................................... 11
Setting ....................................................................... 15 Signal receptor ........................................................... 12
INPUT SELECT Wired connection ........................................................ 15
Appendix

Control panel button .................................................... 12 REMOTE1


Remote control buttons ................................................ 14 Terminal .................................................................... 13
Remote control function ............................................... 22 Wired connection ........................................................ 15
INSTALLATION REMOTE2
Projection method ....................................................... 16 Terminal .................................................................... 13

ENGLISH - 39
Index
RGB1
Control panel button .................................................... 12
Remote control button ................................................. 14
Terminal .................................................................... 13
RGB2
Control panel button .................................................... 12
Remote control button ................................................. 14
Terminal .................................................................... 13

S
Safety cable
Accessories ............................................................... 11
SDI
Control panel button .................................................... 12
Remote control button ................................................. 14
Terminal .................................................................... 13
Security lock ................................................................... 13
SERIAL
Terminal .................................................................... 13
SHIFT
Adjusting ................................................................... 19
Adjustment range ....................................................... 20
Remote control button ................................................. 14
SHUTTER
Control panel button .................................................... 12
Remote control button ................................................. 14
Remote control function ............................................... 22
Specifications ................................................................. 36
STATUS
Remote control button ................................................. 14
Remote control function ............................................... 23
S-VIDEO
Control panel button .................................................... 12
Remote control button ................................................. 14
Terminal .................................................................... 13

T
TEMP
Indicator .................................................................... 12
Indicator status ........................................................... 28
TEST PATTERN
Remote control button ................................................. 14
Remote control function ............................................... 22
Troubleshooting .............................................................. 33
V
VIDEO
Control panel button .................................................... 12
Remote control button ................................................. 14
Terminal .................................................................... 13

Z
ZOOM
Adjusting ................................................................... 19
Remote control button ................................................. 14
Appendix

ENGLISH - 40
Avis important concernant la scurit

Information
Importante
Cher client Panasonic:
Ce mode d'emploi vous donne toutes les informations concernant l'utilisation de ce projecteur. Nous esprons qu'il
vous aidera utiliser au mieux votre nouvel produit, et que vous serez satisfait de votre Projecteur puce DLP
Panasonic. Le numro de srie se trouve au bas de l'appareil. Le noter dans l'espace prvu cidessous et conserver
ce manuel pour le cas o des rparations seraient ncessaires l'avenir.
Numro de modle: PT-DZ6710U/PT-DZ6700U/PT-DW6300U/PT-D6000U

Numro de srie:

ADVERTENCIA: POUR REDUIRE LES RISQUES DE FEU OU DE CHOC LECTRIQUE, NE PAS


EXPOSER CE PRODUIT L'EAU OU L'HUMIDIT.

Alimentation: Ce projecteur LCD est conu pour fonctionner sur secteur de 100 V - 240 V, 50 Hz/60 Hz
seulement.

CAUTION: Le cordon d'alimentation secteur fourni avec le projecteur peut tre utilis uniquement pour une
alimentation lectrique de 125 V, 7 A maximum. Si on veut l'utiliser avec une tension ou un
courant plus forts, on doit se procurer un autre cordon d'alimentation de 250 V. Si on utilise le
cordon fourni sous ces conditions, risque de provoquer un incendie.

Le symbole de la flche en forme d'clair, dans un triangle, avertit l'usager de la prsence de


tensions dangereuses l'intrieur du produit qui peuvent tre de force suffisante pour constituer
un risque de choc lectrique aux personnes.

Le point d'exclamation dans un triangle avertit l'usager de la prsence d'instructions importantes


concernant l'utilisation et l'entretien (rparation) dans la littrature accompagnant le produit.

CAUTION: Cet appareil est quip d'une fiche de courant trois broches avec
mise la terre. Ne pas retirer la broche de mise la masse de la
fiche.
Cette fiche ne pourra tre utilise que dans une prise avec mise la
terre. Ceci est une prcaution scuritaire. S'il est impossible d'insrer
la fiche dans la prise, s'adresser un lectricien. Ne pas annuler la Ne pas retirer
protection de la fiche mise la terre.

Pursuant to at the directive 2004/108/EC, article 9(2)


Panasonic Testing Centre
Panasonic Service Europe, a division of Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, F.R. Germany

NOTICE:
A Ce produit possde une lampe dcharge haute intensit (DHI) qui contient du mercure. Son limination
peut tre rglemente dans votre s cause de considrations environnementales. Pour d'amples
informations sur la mise au rebut ou le recyclage, veuillez contacter vos autorits locales ou aller au site
Web de l'Electronics Industries Alliance: http://www.eiae.org

FRANAIS - 41
Avis important concernant la scurit
Information
Importante

AVERTISSEMENT:
Cet quipement a t soumis des tests qui ont dmontr que celui-ci respectait les limites spcifies pour les
appareils numriques de la classe B aux termes de la partie 15 des rgles de la FCC (Federal Communications
Commission U.S.A.). Ces limites ont pour objet de fournir une protection raisonnable contre les interfrences
nuisibles dans le cas d'une installation en milieu rsidentiel. Cet quipement produit, utilise et peut rayonner de
l'nergie de haute frquence, et s'il n'est pas install et utilis conformment aux instructions fournies avec celui-
ci, peut provoquer des interfrences nuisibles aux communications radio. En outre, mme en cas d'utilisation
conforme, il n'est pas garanti qu'aucune interfrence ne saurait survenir avec certaines installations. Si cet
quipement s'avre nuire la bonne rception d'missions de radiophonie ou de tlvision, ce que l'on pourra
dterminer en mettant l'quipement successivement hors tension puis sous tension, il est conseill de tenter de
remdier au problme par l'une des mthodes suivantes:
- Rorientez ou dplacez l'antenne du rcepteur;
- loignez l'quipement du rcepteur;
- Branchez l'quipement dans une prise de courant situe sur un circuit autre que celui qui alimente la prise de courant du
rcepteur;
- Demandez conseil votre distributeur ou un technicien de radio/tlvision expriment.
FCC CAUTION: Pour assurer la bonne conformit, utilisez uniquement des cbles d'interface blinds lorsque
vous connectez des ordinateurs ou des priphriques. Toute modification non autorise de cet
quipement annulera le droit de l'utilisateur utiliser cet quipement.
Si le port sriel est utilis pour connecter un ordinateur personnel afin de commander le
projecteur depuis l'extrieur, il faut utiliser le cble d'interface sriel en option RS-232C avec
une me en ferrite. Tout changement ou modification non autoris cet quipement annule
l'autorit de faire fonctionner cet appareil.

ADVERTENCIA:
A Ne peut tre utilis dans une salle d'ordinateurs telle que dfinie dans la norme ANSI/NFPA 75 Standard for
Protection of Electronic Computer/Data Processing Equipment.
A Pour l'quipement branch en permanence, un dispositif de dis connexion d'accs facile doit tre incorpor
dans le cble d'installation du btiment;
A Pour l'quipement bran chable, une prise secteur d'accs facile doit tre installe prs de l'quipement.

Dclaration de conformit
Modle n: PT-DZ6710U/PT-DZ6700U/PT-DW6300U/PT-D6000U
Dsignation commerciale:Panasonic
Fabricant responsable: Panasonic Corporation of North America
Adresse: One Panasonic Way, Secaucus, New Jersey 07094
Tlphone: (888) 411 - 1996
Email: projectorsupport@us.panasonic.com
Cet appareil est conforme la partie 15 des rgles de la FCC (Federal Communicaitions Commission U.S.A.) ce
qui signifie: (1) que l'appareil ne produit pas d'interfrences nuisibles, et (2) que l'appareil est capable de supporter
sans danger les interfrences reues, y compris celles susceptibles de perturber son fonctionnement.

Information relative l'limination des dchets dans les pays extrieurs l'Union europenne
Ce pictogramme n'est valide qu'l'intrieur de l'Union europenne. Pour connatre la procdure
applicable dans les pays hors Union Europenne, veuillez vous renseigner auprs des autorits locales
comptentes ou de votre distributeur.

FRANAIS - 42
Prcautions de scurit

Information
Importante
AVERTISSEMENT
Si l'on remarque une mission de fume, d'odeurs sus- Brancher la fiche du cordon d'alimentation fermement
pectes ou de bruits provenant du projecteur, dbrancher dans la prise de courant.
la fiche du cordon d'alimentation de la prise de courant. Ne pas utiliser de cordon d'alimentation autre que celui
Ne pas continuer d'utiliser le projecteur dans ces cas-l, foumi.
autrement cela peut entraner un incendie ou des chocs Si la fiche n'est pas compltement insre, cela peut
lectriques. entraner des chocs lectriques ou la faire surchauffer.
Aprs s'tre assur que de la fume ne se dgage plus, Si la fiche est endommage ou la plaque de la prise
s'adresser un centre technique agr et de-mander que desserre, celles-ci ne devraient pas tre utilises.
les rparations ncessaires soient faites.
Ne pas placer le projecteur sur des surfaces instables.
Le fait de rparer le projecteur soi-mme est trs dan-
gereux, et ne doit jamais tre fait. Si le projecteur est plac sur une surface qui est incline ou
instable, il risque de tomber ou de se renverser et cela peut
Ne pas installer ce projecteur dans un endroit qui n'est pas causer des blessures ou des dommages.
assez rsistant pour supporter le poids du projecteur.
Ne pas placer le projecteur dans l'eau ou ne pas le aisser
Si l'emplacement d'installation n'est pas assez rsistant, le
se mouiller.
projecteur risque de tomber et causer de gra-ves blessures
et (ou) des dommages. Sinon cela peut causer un incendie ou des chocs lec-
triques.
Demander un technicien qualifi d'installer le projecteur
par exemple s'il est install au plafond. Faire attention ne pas endommager le cordon
d'alimentation.
Si l'installation n'est pas faite correctement, cela peut
entraner des blessures ou des chocs lectriques. Ne pas endommager le cordon d'alimentation, ne pas le
modifier, ne pas le placer sous des objets lourds, ne pas le
Ne pas utiliser un support de montage au plafond qui n'est
chauffer, ne pas le placer prs d'objets chauffants, ne pas
pas agr.
le tordre, ne pas le plier ou le tirer excessivement et ne pas
Si de l'eau ou des objets trangers pntrent dans le pro- le rouler en boule.
jecteur, si le projecteur tombe, ou si le botier est endom- Si le cordon d'alimentation est endommag, cela peut
mag, dbrancher immdiatement la fiche du cordon entraner un incendie et des chocs lectriques.
d'alimentation de la prise de courant. Si le cordon d'alimentation est endommag, le faire rparer
Si l'on continue d'utiliser le projecteur dans cette condition, par un centre technique agr.
cela peut entraner un incendie ou des chocs lectriques.
Ne pas placer le projecteur sur des matriaux comme du
S'adresser un centre technique agr pour que les rpa-
tapis ou du tissu ponge.
rations ncessaires puissent tre faites.
Cela peut provoquer une surchauffe du projecteur, pouvant
La prise doit tre monte proximit de l'appareil et doit entraner des brlures, un incendie ou endommager le pro-
tre facilement accessible. jecteur.
Dbranchez immdiatement le cordon d'alimentation de la
Ne pas placer des rcipients de liquide sur le projecteur.
prise si un problme survient.
Si de l'eau se renverse sur le projecteur ou pntre dans
Ne pas surcharger la prise de courant. celui-ci, il y aura risque d'incendie ou d'lectrocution.
Si l'alimentation est surcharge (par exemple, par l'utilisa- Si de l'eau entre l'intrieur du projecteur, entrer en contact
tion de trop d'adaptateurs), cela risque de faire surchauffer avec un centre technique agr.
le projecteur et peut entraner un incendie.
Ne pas mettre d'objets trangers dans le projecteur.
Ne jamais entreprendre toute modification quelconque ou Ne pas insrer d'objets mtalliques ou inflammables dans
dmontage du projecteur. les orifices de ventilation ou les faire tomber sur le project-
Des hautes tensions qui peuvent causer de graves bles- eur, car cela peut causer un incendie ou des chocs lec-
sures sont prsentes l'intrieur du projecteur. triques.
Pour toute inspection, rglage ou rparation, s'adresser
Veiller ce que les bornes + et des piles n'entrent pas en
un centre technique agr.
contact avec des objets mtalliques tels que colliers ou
Nettoyer la fiche du cordon d'alimentation rgulirement pingles cheveux.
afin d'viter toute accumulation de poussire. Sinon, les piles risquent de fuir, de surchauffer, d'exploser
Si de la poussire s'accumule sur la fiche du cordon d'ali- ou de prendre feu.
mentation, l'humidit peut endommager l'isolant et Ranger les piles dans un sac en plastique, et ne pas les
entraner un incendie. Dbrancher la fiche du cordon d'ali- ranger proximit d'objets mtalliques.
mentation de la prise de courant et l'essuyer avec un tissu
sec.
Si le projecteur n'est pas utilis pendant une priode pro-
longe, dbrancher la fiche du cordon d'alimentation de la
prise de courant.
Ne pas manipuler le cordon d'alimentation avec les mains
mouilles.
Cela peut entraner des chocs lectriques.

FRANAIS - 43
Prcautions de scurit
Information
Importante

Ne jamais entrer en contact direct avec le liquide des piles. Lors du remplacement de la lampe, la laisser refroidir pen-
Le liquide risquerait en effet de causer de srieuses bles- dant au moins une heure avant de la manipuler.
sures cutanes. Rincer immdiatement l'eau courante Le couvercle de la lampe devient trs chaud, et on risque
toute trace du liquide des piles puis consulter au plus vite de se brler si on le touche.
un mdecin.
Avant de remplacer la lampe, veiller dbrancher la fiche
Toute pntration du liquide dans l'oeil risque de mme de
du cordon d'alimentation de la prise de courant.
causer la ccit ou d'autres lsions graves. Eviter dans ce
Il y a risque d'lectrocution ou d'explosion.
cas tout prix de vous frotter les yeux, et rincez-les imm-
diatement l'eau courante avant de consulter au plus vite Ne pas laisser des enfants ou des animaux domestiques
un mdecin. toucher la tlcommande.
Pendant un orage, ne pas toucher le projecteur ou le cble. Aprs avoir utilis la tlcommande, la ranger hors de
porte des enfants ou des animaux domestiques.
Il y a risque d'lectrocution.
Aprs avoir retir la pile de la tlcommande, la tenir hors
Ne pas utiliser l'appareil dans un bain ou une douche.
de porte des enfants.
Il y a risque d'incendie ou d'lectrocution.
La pile risque en effet de causer une mort par asphyxie si
Veillez ce que le faisceau lumineux n'claire pas directe- elle est avale.
ment votre peau pendant que vous utilisez le projecteur. Demander immdiatement l'avis d'un mdecin si la pile a
Une lumire intense est mise par l'objectif du projecteur. t avale par quelqu'un.
Si vous vous placez dans ce faisceau lumineux, celui-ci ris-
Isoler la pile avec du ruban adhsif ou autre matriau sim-
quera de vous blesser ou de vous abmer la peau.
ilaire avant de la mettre au rebut.
Ne pas regarder directement dans l'objectif pendant que le La pile risquerait en effet de prendre feu ou mme
projecteur fonctionne. d'exploser en cas de contact avec d'autres objetsmtal-
Une lumire intense est mise par l'objectif du projecteur. liques ou des piles.
Si l'on regarde directement dans cette lumire, elle risque
En cas d'installation au plafond, s'assurer d'utiliser le fil
de causer des blessures et de graves lsions aux yeux.
accessoire ( installer un endroit diffrent que le support
Veiller particulirement ce que les enfants ne regardent
de montage au plafond) ainsi que les oeillets correspon-
pas dans l'objectif. En outre, teindre le projecteur si on le
dants, en tant que mesure de scurit supplmentaire
laisse sans surveillance.
visant empcher toute chute du projecteur.
Ne pas placer les mains ou autres objets prs de l'orifice Des accidents pourraient en effet tre causs par une mau-
de sortie d'air. vaise fixation du projecteur.
De l'air chaud sort par l'orifice de sortie d'air. Ne pas placer
Ne pas placer plusieurs kits les uns sur les autres.
les mains, le visage ou d'autres objets qui ne peuvent
Des accidents pourraient tre causs par un non-respect
rsister la chaleur prs de cette sortie d'air [laisser un
de cette mise en garde.
espace d'au moins 50 cm], sinon des brlures ou des dom-
mages risqueraient de s'ensuivre. N'utilisez pas le projecteur lorsque le couvercle de l'objec-
tif est encore attach l'objectif.
Le remplacement de la lampe ne doit tre effectu que par
un technicien qualifi. Dans le cas contraire, un incendie risque de se produire.
La lampe a une pression interne leve. Si elle est manip-
ule incorrectement, une explosion peut s'ensuivre.
La lampe peut tre facilement endommage si elle est heu-
rte contre des objets durs ou si on la laisse tomber et des
blessures et des mauvais fonctionnements peuvent
s'ensuivre.

MISES EN GARDE
Ne pas obstruer les orifices d'entre et de sortie d'air. Ne jamais utiliser le projecteur dans un environnement
Cela risque de faire surchauffer le projecteur, et causer un hautes temprature, par exemple proximit d'un radia-
incendie ou endommager le projecteur. teur ou directement soumis aux rayons du soleil.
Ne pas installer le projecteur dans des endroits troits, mal Le non-respect de cette mise en garde riquerait de causer
ventils tels que des placards ou des tagres. un incendie, un dyfonctionnement ou une dtrioration du
Ne pas placer le projecteur sur des tissus ou du papier, ces plastique.
matriaux peuvent tre aspirs dans l'orifice d'entre d'air. Ne pas utiliser le projecteur l'air libre.
Ne pas installer le projecteur dans des endroits humides Ce projecteur a t conu pour une utilisation en intrieurs.
ou poussireux ou dans des endroits o le projecteur peut
Pour dbrancher le cordon d'alimentation, tenir la fiche et
entrer en contact avec des fumes grasses ou de la va-
non pas le cordon.
peur.
Si le cordon d'alimentation est tir, le cordon sera endom-
L'utilisation du projecteur dans de telles conditions peut
mag et cela peut causer un incendie, des courts-circuits
causer un incendie, des chocs lectriques ou une dtrio-
ou des chocs lectriques srieux.
ration du botier en plastique. Une dtrioration du plas-
tique risquerait en effet d'entraner une chute du projecteur
en cas d'installation au plafond.

FRANAIS - 44
Prcautions de scurit

Information
Importante
Dbrancher toujours tous les cbles avant de dplacer le Ne jamais rutiliser une lampe usage.
projecteur. La lampe risquerait en effet d'exploser.
Le fait de dplacer le projecteur avec des cbles branchs
Ne pas peser de tout son poids sur ce projecteur.
peut endommager les cbles, ce qui pourrait causer un
incendie ou des chocs lectriques. On risque de tomber ou de casser l'appareil, ce qui peut
causer des blessures.
Ne pas placer d'objets lourds sur le projecteur. Veiller tout particulirement ce que les enfants ne se tien-
Cela peut dsquilibrer le projecteur et le faire tomber, ce nent pas debout ou ne s'asseyent pas sur le projecteur.
qui peut entraner des dommages ou des blessures.
Dbrancher la fiche du cordon d'alimentation de la prise
Ne pas court-circuiter, chauffer ou dmonter les piles, et de courant comme mesure de scurit avant d'effectuer
ne pas les mettre dans l'eau ou dans le feu. tout nettoyage.
Si l'on insre des piles d'un type diffrent, elles risqueront Sinon cela peut causer des chocs lectriques.
d'exploser ou de fuir, ce qui peut causer un incendie, des
blessures ou une contamination du logement des piles et Si la lampe s'est casse, ventiler immdiatement la pice.
de la zone environnante. Ne pas toucher ni approcher le visage des morceaux
casss.
Lorsqu'on insre les piles, veiller ce que les polarits (+ Le non respect de cette consigne peut entraner l'absorp-
et ) soient bien respectes. tion du gaz par l'utilisateur. Ce gaz se dgage lorsque la
Si l'on insre les piles incorrectement, elles risqueront lampe est casse et il contient presque autant de mercure
d'exploser ou de fuir, ce qui peut causer un incendie, des qu'une lampe fluorescente, de plus les morceaux casss
blessures ou une contamination du logement des piles et peuvent provoquer des blessures.
de la zone environnante. Si vous pensez avoir inhal du gaz ou que du gaz a
Utiliser uniquement les piles spcifies. pntr dans votre bouche ou dans vos yeux, contactez un
mdecin immdiatement.
Si l'on insre des piles d'un type diffrent, elles risqueront
d'exploser ou de fuir, ce qui peut causer un incendie, des S'adresser au revendeur pour le remplacement de la lampe
blessures ou une contamination du logement des piles et et l'inspection de l'intrieur du projecteur.
de la zone environnante. Demander un centre technique agr de nettoyer
Ne jamais mlanger des piles neuves et usages. l'intrieur du projecteur au moins une fois par an.
Si des piles usages et neuves sont mlanges, elles ris- S'il n'est pas nettoy et que de la poussire s'accumule
quent d'exploser ou de fuir, ce qui peut causer un incendie, l'intrieur du projecteur, cela peut causer un incendie ou
des blessures ou une contamination du longement des des problmes de fonctionnement.
piles et de la zone environnante. Il est recommand de nettoyer l'intrieur du projecteur
avant l'arrive de la saison humide. Demander au centre
Retirer rapidement les piles de la tlcommande. technique agr le plus proche de nettoyer le projecteur
Si vous laissez des pile usages dans la tlcommande lorsque cela est requis. Se renseigner auprs du centre
pendant une longue priode, cela risque de provoquer des technique agr pour le cot du nettoyage.
fuites, une hausse anormale de la temprature interne ou
une explosion. Ne pas utiliser de chiffons traits chimiquement pour le
nettoyage.
Si le projecteur ne doit pas tre utilis pendant une longue L'utilisation de chiffons traits chimiquement peut provo-
dure dbrancher la fiche lectrique de la prise de courant quer la dformation ou la dtrioration du plastique.
et ter les piles de la tlcommande.
Si de la poussire s'accumule sur la fiche du cordon d'ali- Ne pas toucher les ouvertures situes derrires l'objectif
mentation, l'humidit ainsi cre risquera d'endommager pendant les mouvements horizontaux ou verticaux de ce-
l'isolation, ce qui peut provoquer un incendie. lui-ci.
Si les piles restent dans la tlcommande, il existe un ris- Sinon des blessures pourraient en rsulter.
que de dtrioration par insulation et de fuite lectrique ou Le remplacement de la lampe ne doit tre effectu
d'explosion pouvant causer un incendie. qu'aprs que celle-ci ait compltement refroidi.
Sinon des brlures pourraient en rsulter.

Nous faisons tous les efforts possibles afin de prserver l'environnement. Prire de rapporter l'appareil, s'il
n'est pas rparable, votre revendeur ou un centre de recyclage.

Prcautions lors du transport


Ne pas soumettre le projecteur des vibrations ou des Veillez toujours retirer l'objectif pendant le transport.
chocs excessifs. L'objectif de projection est sensible aux vibrations et aux
L'objectif du projecteur doit tre manipul avec soin. impacts.
Placer le couvercle sur l'objectif lors du transport du projec-
teur.
Lors du transport du projecteur, bien le tenir par le bas.
Ne pas tenir le projecteur par les pieds de rglage ou le
couvercle suprieur pour le dplacer car cela pourrait
l'endommager.

FRANAIS - 45
Prcautions de scurit
Information
Importante

Prcautions lors de l'installation


viter de l'installer dans les endroits sujets des vibra- Si le projecteur est install au plafond, demander a un
tions ou des chocs. technicien qualifi de faire tous les travaux d'installation.
Les pices internes peuvent tre endommages, ce qui Il faut acheter le kit d'installation spar (numro de
peut causer des pannes ou des accidents. modle: ET-PKF100H, ET-PKF100S). En outre, tous les
travaux d'installation doivent tre excuts uniquement par
viter d'installer le projecteur des endroits sujets des
un technicien qualifi.
changements de temprature brusques, proximit d'un
climatiseur ou d'un matriel d'clairage. Si l'on utilise ce projecteur un endroit lev 1 400 -
La dure de vie de la lampe risquerait d'tre rduite, ou le 2 700 m (4 593 - 8 858 ft), rgles MODE HAUTE ALTITUDE
projecteur risquerait de s'teindre. Indicateur TEMP la sur OUI.
page 41. Le non-respect de ces consignes peut entraner un dys-
fonctionnement ou peut raccourcir la dure de vie de la
Ne pas installer le projecteur prs de lignes d'alimentation
lampe ou d'autres composants.
lectrique haute tension ou de moteurs.
Le projecteur peut tre soumis des interfrences lectro- Veillez installer le couvercle de l'objectif de projection
magntiques. aprs avoir install l'objectif de projection.
Dans le cas contraire, de la poussire risquerait de s'accu-
muler l'intrieur du projecteur et de causer des prob-
lmes.

Prcautions lors de l'utilisation


Afin d'obtenir la meilleure qualit d'image Puces DLP
Fermer les rideaux ou les volets de toutes les fentres et Les puces DLP sont fabriques l'aide d'une technologie
teindre les lampes fluorescentes situes proximit de de trs haute prcision. Veuillez noter qu'en de rares cas,
l'cran afin que la lumire extrieure ou la lumire des lam- des pixels peuvent manquer ou tre toujours allums, mais
pes intrieures n'claire pas l'cran. il ne s'agit pas d'un dysfonctionnement.
Dans certains cas peu frquents, dpendant avant tout des
Ce projecteur est quip d'une lampe au mercure sous
conditions de projection, il est possible que des parasites
haute pression, dont les principales caractristiques ont:
se forment l'cran en raison de l'air chaud s'chappant du
La luminosit de la lampe dpend de la dure d'utilisation.
port d'vacuation d'air. S'assurer qu'il n'y a aucun appareil
capable de faire recirculer l'air chaud vacu du projecteur Les chocs et clats risquent d'endommager ou de rduire
en face de celui-ci ou d'un autre appareil proche. la dure de vie de la lampe.
Un risque d'explosion rduit existe pendant la dure d'utili-
Ne pas toucher aux surfaces de l'objectif ou du verre avant sation du projecteur.
avec les mains nues. La lampe risque d'exploser si son utilisation dpasse la
Si la surface de l'objectif est salie par des empreintes dure recommande de remplacement de la lampe.
digitales ou autre, celles-ci seraient agrandies et projetes Si la lampe explose, elle met un gaz interne semblable
sur l'cran. De plus, refermer le Couvercle du panneau de la fume.
avant lorsque le projecteur n'est pas utilis. La dure de vie de la lampe dpend de ses caractris-
Composants optiques tiques, des conditions d'utilisation et de l'environnement
En cas d'utilisation quotidienne du projecteur pendant d'installation. La dure de vie de la lampe peut tre par-
12 heures ou plus, les composants optiques devront tre ticulirement raccourcie par une utilisation continue de plus
remplacs en moins d'1 an. de 22 heures ou des mises en marche/arrt frquentes.
Prvoyez une lampe de rechange d'avance.
Ne jamais utiliser le projecteur lorsque les pieds rglables
ou l'objectif de projection sont retirs.
Sinon, l'appareil pourrait ne pas fonctionner correctement
ou des accidents pourraient en rsulter.

Autres
Mise au rebut Connexion un appareil externe
Lors de la mise au rebut du produit, contacter la municipal- Lors de la connexion du projecteur un ordinateur ou un
it ou le distributeur le plus proche afin de vrifier la proc- appareil externe, utilisez le cordon d'alimentation fourni
dure approprie de mise au rebut. avec l'appareil correspondant et un cble d'interface blind
disponible dans le commerce.

FRANAIS - 46
Prcautions de scurit

Information
Importante
Scurit
Suivez les mesures de scurit lors de l'utilisation du pro- Modifiez frquemment votre mot de passe.
jecteur pour prvenir les ventuels incidents suivants. Ne pas utiliser de mot de passe trop facile deviner.
La fuite d'informations enregistres personnelles. Le mot de passe ne vous sera jamais demand par le Cen-
Les activits malhonntes accomplies par une tierce partie tre de dpannage agr.
non digne de confiance. Ne jamais rvler votre mot de passe.
L'utilisation du projecteur par une tierce partie non de confi- Attribuer un mot de passe au projecteur et restreindre son
ance (pour viter une telle situation, vous pouvez verrouiller accs uniquement aux utilisateurs autoriss.
le projecteur).
Instructions de scurit
Instructions de scurit Le rseau de connexion doit tre scuris par un pare-feu
Le rseau de connexion doit tre scuris par un parefeu et et autres.
autres. Modifiez frquemment votre mot de passe.
Ne pas utiliser de mot de passe trop facile deviner.
Le mot de passe ne vous sera jamais demand par le Cen-
tre de dpannage agr.
Ne rvlez jamais votre mot de passe.
Attribuer un mot de passe au projecteur et restreindre son
accs uniquement aux utilisateurs autoriss.

FRANAIS - 47
Remplacement
Imformation
Importante

J Avant de remplacer le l'Unit de la lampe


Mettez l'POWER duprojecteur en position approprie et dbranchez la fiche de la prise du secteur.
Attendez plus d'1 heure et vrifiez que la lampe et l'environnement aient suffisamment refroidi.
Prparer un tournevis cruciforme.
Contactez le distributeur pour acheter une lampe de rechange (ET-LAD60 : 1 ampoule, ET-LAD60W :
2 ampoules).
Lorsque le projecteur est mont au plafond, ne travaillez pas directement sous le projecteur et n'en
approchez pas le visage.

ATTENTION:
Les chocs et clats risquent de rduire la dure de vie de la lampe ou de la faire exploser.
REMARQUE:
Avant de remplacer la lampe, laissez-la refroidir afin d'viter tout risque de brlure, de dgts ou d'autres dangers.
N'essayez pas de la remplacer par une lampe non agre.

J Dlai de remplacement de l'unit de la lampe


La lampe est un consommable et sa luminosit diminue mesure que la dure d'utilisation augmente. Les
tmoins LAMP1/LAMP2 vous informeront du moment de remplacement 1 800 heures, et 2 000 heures, le
projecteur s'teindra. Ces chiffres sont des valeurs approximatives et pourraient s'avrer infrieures selon les
conditions d'utilisation, les caractristiques de la lampe, les conditions environnementales, etc. Vous pouvez
vrifier la dure d'utilisation l'aide de LAMPE1/LAMPE2 de TAT dans le menu RGLAGE PROJECTEUR.

A l'cran LAMP Indicateur

REMPLACER LA LAMPE
Indication

LAMP
REMPLACER LA LAMPE est affich
dans la partie suprieure gauche de l'cran
Plus de 1 800 heures pendant 10 minutes. Appuyez sur n'importe
quelle touche pour effacer l'cran ou
s'efface aprs 10 minutes.
REMPLACER LA LAMPE est affich S'allume en rouge.
dans la partie suprieure gauche de l'cran
et y demeure jusqu' ce que vous
Plus de 2 000 heures
rpondiez.
Pour effacer l'cran, appuyez sur n'importe
quelle touche.

ATTENTION:
Si vous continuez utiliser la lampe au-del de 2 000 heures, elle endommagera le projecteur. Le projecteur sera mis hors tensions
aprs 10 minutes.
REMARQUE:
Les dures indiques, de 1 800 et 2 000 heures, sont des estimations bas sur certaines conditions et ne reprsentent en aucun cas des
dures garanties.
Pour de plus amples informations sur la lampe, telle que la dure de fonctionnement garantie, voir les instructions fournies avec la
lampe.

FRANAIS - 48
Remplacement

Information
Importante
J Procdure de remplacement
Q Retirer et remplacer la lampe
1. Utilisez un tournevis cruciforme pour desserrer la 4. Tenez la poigne de la nouvelle lampe et replacez-
vis de fixation du couvercle de la lampe l'arrire la dans la direction correcte.
du projecteur jusqu' ce que les vis tournent 5. Appuyez sur la lampe jusqu' ce qu'elle fasse
librement, puis retirez le couvercle de la lampe. entendre un dclic et vrifiez qu'elle est bien en
Faites glisser le couvercle de la lampe jusqu'aux place.
boutons et tirez dessus pour l'ter. 6. Serrez fermement les 3 vis de fixation de la lampe
l'aide d'un tournevis cruciforme.

Vis de fixation du
couvercle de la lampe

Connecteur d'alimentation
lectrique du ventilateur

Couvercle de la
lampe

2. Utilisez un tournevis cruciforme pour retirer les


3 vis de fixation de la lampe.
3. Tenez les poignes de la lampe et tirez doucement
la lampe usage hors du projecteur. 7. Montez le couvercle de la lampe et serrez
Vis de la lampe Poigne fermement la vis de fixation du couvercle de la
lampe l'aide d'un tournevis cruciforme.
Faites glisser le couvercle de la lampe du ct de la
charnire et poussez-le pour le monter fermement.
Vrifiez que le connecteur d'alimentation lectrique
du ventilateur est bien introduit sur le connecteur du
projecteur.

Poigne Vis de la lampe

FRANAIS - 49
NOTE:
This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material - special handling may
apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate.

Printed in Japan
S0209-1039B
TQBJ0295

You might also like