Manual Peugeot 307 PDF

YOUR 307 AT A GLANCE 1
Pages
Seats 92 - 101
Steering wheel controls 110 - 116
Instrument dials 28 - 29
Heating, air conditioning 84 - 91
Mirrors 118 - 119
Pages
Checks 143 - 151
Access 106 - 109
Fuel filler flap 109
Changing a bulb 158 - 160
Changing a wheel 152 - 157
Each model may only be fitted with some of the equipment shown, according to its specification and the technical
requirements in the country of first registration of the vehicle.
Estate: model available according to country.
29-09-2003
2 YOUR 307 AT A GLANCE
29-09-2003
1- Driver's air bag. 15 - Side adjustable heating/

Horn. ventilation vent and air flow
regulation.
2- Lights and direction
indicators stalk. 16 - Passenger air bag.
30 - Coin storage.
3- Audio remote control stalk. 17 - Glove box. Passenger air bag
disarming switch*.
4- Instrument dials. 18 - RB3, RD3 or RT3
audio/telephone 31 - Steering lock and ignition.
5- Windscreen wash-wipe equipment.
stalk. 32 - Bonnet opening control
Trip computer stalk.
19 - Heated seat switches. 33 - Steering wheel adjustment
6- Alarm button. control.
20 - CD changer.
7- Central locking button. 34 - Fuse box.
21 - Heating/air conditioning
8- Hazard warning lights controls. 35 - Electric mirror controls.
switch. Window controls.
22 - Front ashtray. Rear window disarming
control.
9- Multi-function display.
23 - Side air bags.
36 - Headlamp height
10 - Electronic stability control adjustment.
(ESP/ASR) button. 24 - Rear footwell heating vent.
37 - Cruise control/speed
11 - Central adjustable 25 - 12 V accessories socket. limiter** control.
heating/ventilation vent and
air flow regulation.
26 - Gear lever.
12 - Windscreen demisting
vents. 27 - Can holder.
13 - Speaker (tweeter). 28 - Handbrake. * According to destination.

** During the year, according to
14 - Side window demisting vent. 29 - Waste container. engine.
29-09-2003
The remote control key Unlocking

Locking Press button B to unlock the vehi-
Press button A to lock the vehicle. cle.
This is confirmed by
This is confirmed by fixed lighting rapid flashing of the
of the direction indicators for direction indicators.
approximately two seconds.
Note: a long press on button A, Note: If the vehicle is 102
in addition to locking, automati- locked and unlocking
THE KEYS cally closes the windows and the is activated inadvertently, unless
sunroof. the doors are opened within 30
The keys allow you to switch on seconds, the vehicle will lock auto-
the ignition and operate the pas- Vehicles fitted with matically.
senger air bag disarming switch deadlocking
as well as to independently oper- STARTING
ate the locks on the front doors, Deadlocking renders the
the fuel filler cap and the glove internal and external STOP position:
box. door locking controls The ignition is off.
inoperative. 1st notch, Accessories position:
Press button A to dead- The ignition is off but the acces-
Central locking lock the vehicle. sories can be used.
From the driver's door, the keys This is confirmed by fixed lighting 2nd notch, Running position:
allow you to lock, deadlock or of the direction indicators for The ignition is on.
unlock the doors and the tailgate approximately two seconds. Starting position:
as well as to fold back the exterior Operates the starter.
mirrors. Note: a long press on button A
permits automatic closing of the
If one of the doors or the boot is windows and the sunroof, in
open, it is impossible to operate addition to deadlocking.
the central locking; an audible A second press on button A in
signal indicates this when lock- the five seconds following dead-
ing by remote control. locking, changes deadlocking to
The remote control performs normal locking.
the same functions at a This is confirmed by fixed lighting
distance. of the direction indicators for
approximately two seconds.
29-09-2003
STEERING WHEEL Vehicles fitted with a rear fog

STALKS lamp (ring B) WINDSCREEN WIPERS
Front
LIGHTING Rear fog lamp (rotation
of the ring forwards) 2 Rapid wipe
Front and rear lights (ring A) (heavy rain).
1 Normal wipe
(moderate rain).
Lights off. AUTO Automatic wipe.
Vehicles fitted with front fog
lamps and a rear fog lamp 0 Off.
(ring C) Single wipe.
Side lights. Windscreen wash-wipe: pull the
stalk towards you.
Front fog lamps Automatic wipe
Dipped/main (first rotation of the ring In the AUTO position,
beam headlamps. forwards) the wiper operates auto-
matically and adjusts
Automatic its speed to the inten-
switching on Front fog lamps and sity of the rainfall. 112
of the lights. rear fog lamp
(second rotation of
the ring forwards) Rear
Automatic switching on
of the lights Off Intermittent Windscreen
To activate or deactivate the wipe wash-wipe
Switching off: rotation of
function, place the key in the the ring backwards.
accessories position, the lights
stalk in position 0 and press the 110
end of the lights stalk for more
than two seconds.
29-09-2003
FRONT SEATS
1- Forwards-backwards
adjustment.
2- Access to rear seats
(3 door).
3- Seat back angle adjustment.
4- Driver or passenger seat
height adjustment.
5- Heated seats switch.
6- Front removable armrest
(5 door).
7- Head restraint height and
angle adjustment.
To raise or lower the head
restraint, pull it forwards,
sliding it at the same time.
Never drive with the

head restraints removed.
8- Storage drawer.
92
29-09-2003
REAR SEATS
To fold down the rear left seat (2/3 part) or right seat (1/3 part),
always start with the cushion, never with the seat back (there is a risk of damage):
Move the front seat(s) forward if necessary,
Tilt the seat cushion 1 against the front seat(s),
Estate: tilt using the handle.
Check that the seat belt is in the correct position on the side of the seat back,
Pull control 2 forwards to unlock the seat back 3,
Place the head restraints in the low position,
Tilt the seat back 3.
Note: the seat cushion 1 can be removed to increase the volume of the load space.
When refitting:
Fold the seat back and lock it (the red marker of control 2 must no longer be visible),
Fold back the seat cushion.
Take care not to trap the seat belts. 94
29-09-2003
AIR BAGS Disarming the passenger Disarming check

air bag*
The air bag system has been With the ignition off, insert With the ignition switched
designed to maximise the safety the ignition key into the pas- on (2nd notch), illumina-
of the occupants in the event of senger air bag slot 1 and turn tion of this warning light,
serious collisions. It works in con- it to the "OFF" position. accompanied by an audi-
junction with the force limiting ble signal and the message
seat belts. "Passenger air bag deactivated"
As soon as you remove the child on the multi-function display, indi-
seat, turn the air bag switch to the cates that the passenger air bag
"ON" position, to activate the air is disarmed (slot in the "OFF"
Front air bags bag again. position).
These are folded in the centre of The warning light remains on
the steering wheel for the driver throughout the disarming process.
and in the fascia for the front pas-
senger. They are deployed simul-
taneously, except in cases where Side air bags*
the passenger air bag is disarmed. and curtain air bags*
Side air bags are incorporated
into the front seat back frame, on
Precautions regarding the door side.
the passenger air bag
Curtain air bags are incorporated
into the door pillars and the top of
disarm the air bag if you the passenger compartment.
install a rear-facing child seat, They are deployed independently
activate the air bag for an of each other, on whichever side
adult passenger. the collision occurs.
* According
140 to destination. 141
29-09-2003
ELECTRIC WINDOWS STEERING WHEEL

1. Driver's electric window. HEIGHT AND DEPTH
2. Passenger's electric window. ADJUSTMENT
3. Rear right electric window.
4. Rear left electric window.
5. Disarming the rear window switches.
When stationary, pull handle A
to unlock the steering wheel.
Manual operation: Automatic operation:
Adjust the height and depth of
Press or pull the switch lightly. Press or pull the switch firmly. the steering wheel.
The window stops as soon as One touch completely opens Lock it by pushing handle A in
the switch is released. or closes the window. fully.
Safety auto-reverse: When the window is rising and meets

an obstacle, it stops and lowers again.
117
ELECTRIC MIRRORS
Slide switch 6 to the right or When parking the vehicle, the
left to select the corresponding mirrors can be folded back, elec-
mirror. trically by pulling
Then move button 7 in all four button 6 rearwards or
directions to adjust. automatically on locking
the vehicle.
Return switch 6 to the centre
position. 118 120
29-09-2003
Memorising a speed
When you reach the required
speed, press button 2 or 3. The
speed is memorised and will be
maintained automatically.
Note: it is possible to accelerate
temporarily without deactivating
the cruise control.
Deactivating the memorised
CRUISE CONTROL speed REAR PARKING
If you wish to deactivate the ASSISTANCE
The cruise control makes it possi-
ble to maintain a constant vehicle memorised speed: This system, installed in the rear
speed, programmed by the driver, press button 4 or the brake or bumper, detects any obstacle
irrespective of the profile of the clutch pedal. (person, vehicle, tree, barrier,
road and without any action on the etc) behind the vehicle.
accelerator or the brake pedals. Recalling the memorised
speed Activation
In order for the vehicle speed to
be memorised, it must be greater With the engine running, the sys-
than 25 mph (40 km/h) (manual After deactivation, press button 4. tem is activated when reverse
gearbox) or 37 mph (60 km/h), Your vehicle reverts to the last gear is engaged; a bleep indi-
(automatic gearbox), with at least memorised speed. cates that it is active.
4th gear engaged (2nd gear for Cancelling the stored speed The proximity information is given
the automatic gearbox). by an audible signal, consisting of
Place knob 1 in the OFF posi-
Activation tion or switch off the ignition. bleeps which become faster as
the vehicle approaches the
Place knob 1 in the ON position. obstacle.
A speed can now be memorised. When the distance between the rear
of vehicle and the obstacle is less
Place knob 1 in the OFF posi- than thirty centimetres, the audible
tion to deactivate the system. signal becomes continuous.
Do not use the cruise
control on slip- In neutral, the system
pery roads or in becomes inactive again.
heavy traffic.
135 139
29-09-2003
OPENING THE BONNET
FILLING WITH FUEL Inside the vehicle: Push the

handle on the left-hand side,
This operation must be carried out with the engine switched off. under the fascia.
Open the fuel filler flap.
Insert the key then turn it to the left.
Remove the cap and hook it onto the clip on the inside of the flap.
A label on the inside of the flap shows which type of fuel to use.
When you fill your tank, do not continue after the 3rd cut-off of the pump.
This could cause a malfunction.
The capacity of the tank is approximately 60 litres.
After filling the tank, lock the cap and close the flap.
Outside the vehicle: Lift

Low fuel level warning light the catch, raise the
bonnet and secure the
From the time this light comes on, you have enough fuel strut to keep the bonnet
remaining to drive for approximately 30 miles (50 km). 109 open. 109
29-09-2003
AUTOMATIC GEARBOX "PORSCHE TIPTRONIC SYSTEM"

The four-speed automatic gearbox offers a choice between the comfort
of automatic integral regulation enhanced by a sport and snow pro-
gramme, or the pleasure of manual gear changing.
Gear selection gate
Moving Off
Move the lever in the gate to select one of the functions.
Once the function is selected, the indicator light for that function is dis- With the engine running, to move
played on the instrument panel screen. off from position P:
It is essential to press the
brake pedal to exit position P,
S: sport programme. Select the function R, D or M,
then gradually release the
: snow programme. pressure on the brake pedal;
Park: to immobilise the vehicle or to start the the vehicle will move off imme-
engine, with the handbrake on or off. diately.
You can also move off from posi-
Reverse: to reverse (select this function with the tion N:
vehicle stationary and the engine at idle).
Release the handbrake, with
Neutral: to start the engine or to park, with the your foot on the brake.
handbrake on. Select function R, D or M,
Note: if position N is engaged by mistake while then gradually release the
the car is moving, allow the engine to return to pressure on the brake pedal;
idling speed before engaging function D to accel- the vehicle will move off
erate. immediately.
Drive: for automatic gear changing. When the engine is idling
Manual: for manual gear changing. with the brakes not
applied, if function R, D
or M is selected, the vehi-
cle moves without the
To change the four gears manually: accelerator being pressed.
Push the lever to the + symbol to change up a gear and pull the lever For this reason, do not
towards the symbol to change down a gear. leave children unsuper-
Note: the S (sport) and (snow) programmes do not operate when in vised inside the vehi-
manual mode. cle, with the engine
running. 130
29-09-2003
HEATING/AIR CONDITIONING
N Symbol Function
Setting the
1
air distribution.
Air intake
2
control.
86
Temperature
3
adjustment.
Demisting
4 the rear screen
and mirrors.
Air flow
5
adjustment.
Air conditioning
6
control.
88
29-09-2003
AUTOMATIC AIR CONDITIONING
N Symbol Function
1 Air flow adjustment.
Setting
2
the air distribution.
Air intake
3
control.
Air conditioning
4 control.
Demisting
5 the rear screen
and mirrors.
6 Switching off.
Temperature
7
adjustment.
Automatic comfort
8
programme.
Automatic visibility
9
90 programme.
29-09-2003
18
PEUGEOT SERVICING
PEUGEOT SERVICING
Your vehicle benefits from extended service intervals.
For petrol engines: every 20,000 miles (30 000 km) or every two years.
For direct injection diesel engines: every 12,000 miles (20 000 km) or every two years.
The service indicator informs you when each service is due; the point at which it is due is calculated from the last indicator
zero reset (see corresponding section).
This point is determined by two parameters:

the distance travelled,
the time elapsed since the last service.
Note: the distance remaining may be weighted by the time factor, in accordance with the driver's style of driving.
The extension of the service intervals means that the engine oil level must be checked regularly: topping up of the
oil between oil changes is normal.
It is for this reason that the PEUGEOT network invites you to an intermediate visit between regular services.
The date of this service is not shown by the service indicator. It is to be carried out at least every 10,000 miles
(15 000 km) for petrol engines and every 6,000 miles (10 000 km) for direct injection diesel engines.
A PEUGEOT dealer will carry out a quick check, and will top up the levels if necessary (oil, coolant, screenwash up
to 2 litres).
If the oil level is too low there is a risk of serious damage to the engine: check the engine oil level at least every
2,000 miles (3 000 km) or 3,000 miles (5 000 km), depending on the conditions of use.
The extended service intervals have been made possible by technical modifications to the vehicles and lubricants:
THUS IT IS ESSENTIALTO ONLY USE LUBRICANTS WHICH ARE SUITED TO YOUR ENGINE AND RECOMMENDED
BY THE MANUFACTURER (see pages on "Lubricants").
29-09-2003
20
PEUGEOT SERVICING
SERVICE INDICATOR 5 seconds after the ignition was swit- The service is overdue.
ched on, the distance recorder
resumes its normal operation and The service spanner flashes for
This indicates when the next service 5 seconds after the ignition is swit-
is due in accordance with the manu- the display indicates the total and trip
distance. ched on.
facturer's servicing schedule.
Example: the service is overdue by

300 km, your vehicle must be servi-
Operation ced as soon as possible.
For 5 seconds after the ignition is For 5 seconds after the ignition is
switched on, the spanner symboli- switched on, the display indicates:
sing the servicing operations comes
on; the distance recorder display
indicates the number of miles [kilo-
metres] (rounded off) remaining until
the next service.
The distance remaining to the
next service is less than 1,000 km.
Example: 900 km remain before the
Example: 4,800 km remain before next service.
the next service. For five seconds
after the ignition is switched on, the For 5 seconds after the ignition is
display indicates: switched on, the indicator displays:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the service spanner remains lit. The
display indicates the total and trip
distance.
Note: the service spanner may also

5 seconds after the ignition was swit- come on if more than two years have
ched on, the distance recorder elapsed since the last service (refer to
resumes its normal operation and the "PEUGEOT Servicing" section).
the spanner remains lit.
It indicates that a service must be
carried out soon. The display indi-
cates the total and trip distance.
29-09-2003
21
PEUGEOT SERVICING
Zero re-set MAINTENANCE OF PARTS SUBJECT TO WEAR and a check of

Your PEUGEOT dealer carries out consumables
this operation after each service. Certain essential components on your vehicle are subject to checks at specific
However, if you carry out the service frequencies:
yourself, the re-set procedure is as
follows: The brake fluid is to be replaced at a maximum of every 36,000/40,000 miles
Switch off the ignition, (60 000 km) or every two years.
Press and hold the trip recorder The passenger compartment filter must be checked at each service by a
re-set button, PEUGEOT dealer (services and intermediate visits) or more often, depending
Switch on the ignition. on the environment (dust, pollution, etc.)
The display begins a countdown. Replacement of the timing belt: consult a PEUGEOT dealer.
When the display shows "0000.0", For the 2 litre HDI turbo diesel engines (110 bhp and 16V), maintenance of
release the button; the service the particulate emission filter and topping up of the additive reservoir must
symbol disappears. be carried out at a maximum of every 72,000 miles (120 000 km), by a
PEUGEOT dealer. If the message "Diesel additive minimum level" is
Important: after this operation, if you displayed on the multi-function display accompanied by an audible signal,
wish to disconnect the battery, lock contact a PEUGEOT dealer who will top up the additive reservoir.
the vehicle and wait for at least five The check on tyre inflation pressure must be carried out cold at least once
minutes, otherwise the zero re-set a month.
will not be registered.
29-09-2003
22
PEUGEOT SERVICING
TYPES OF SERVICE
Each vehicle has its own servicing cycle, based upon the engine type.
This cycle consists of alternating two types of service, A and C, intermediate visits and a few additional operations depending
on your vehicle; these correspond to key stages in the life of your vehicle.
When the first service is carried out and at each subsequent service, your dealer will advise you of the type and
content of the next service due.
MAINTENANCE CYCLE FOR YOUR 307 PETROL ENGINE

Service every 2 years or 20,000 miles (30 000 km) maximum
MILES (KM) 20,000 (30 000) 40,000 (60 000) 60,000 (90 000)
1st service at 6,000 miles
(10 000 km) or 6 months*.
This is necessary in order to
benefit from the warranty.
80,000 (120 000) 100,000 (150 000) 120,000 (180 000) 140,000 (210 000) 160,000 (240 000)
These services are to be carried out with 10W40 synthetically based oil minimum.
5W40 synthetic oil or 5W30 fuel economy oil may also be used.
Arduous conditions of use (see corresponding section).
Intermediate visit included

in the Fixed Services.
* Whichever comes first.
29-09-2003
23
PEUGEOT SERVICING
MAINTENANCE CYCLE FOR YOUR 307 DIESEL

Service every 2 years or 12,000 miles (20 000 km) maximum
MILES (KM) 12,000 (20 000) 24,000 (40 000) 36,000 (60 000) 48,000 (80 000) 60,000 (100 000)
1st service at 6,000 miles

(10 000 km) or 6 months*.
This is necessary in order
to benefit from the warranty.
72,000 (120 000) 84,000 (140 000) 96,000 (160 000) 108,000 (180 000) 120,000 (200 000) 132,000 (220 000) 144,000 (240 000)
+ maintenance of particulate + maintenance of particulate

emission filter for 2.0 litre emission filter for 2.0 litre
HDI 110 bhp and 2.0 litre HDI 110 bhp and 2.0 litre
HDI 16V engines HDI 16V engines
These services are to be carried out:

imperatively with 5W40 synthetic oil for HDI Turbo Diesel engines fitted with a particulate emissions filter,
with synthetically based oil, synthetic oil or Fuel Economy oil for the other HDI Turbo Diesel engines,
imperatively with 5W40 synthetic oil or Fuel Economy Oil for the 1.4 litre HDI Turbo Diesel engine.
Arduous conditions of use (see corresponding section).
Intermediate visit included

in the Fixed Services.
* Whichever comes first.
29-09-2003
24
PEUGEOT SERVICING
ARDUOUS CONDITIONS OF USE
Continuous door-to-door use.

Town use (e.g. taxi).
Repeated short journeys, with the engine cold at low temperatures.
A prolonged stay under the following conditions:
countries with temperatures often above +30 C,
countries with temperatures often below 15 C,
countries with a dusty atmosphere,
countries whose lubricants or fuels do not conform to our recommendations.
It is necessary to follow an "Arduous Conditions" servicing schedule which has shorter service intervals:
Every 12,000 miles (20 000 km) or every year for Petrol engine vehicles.
Every 10,000 miles (15 000 km) or every year for Diesel engine vehicles.
29-09-2003
25
PEUGEOT SERVICING
A AND C SERVICE LEVELS AND THE INTERMEDIATE VISIT
Level
Operations Description of operation 1st service
A C Intermediate
Engine oil
DRAIN/REFILL Bleed fuel filter (diesel)
Oil filter
Fuel filter* (petrol)
REPLACE Fuel filter element (diesel)
Air filter element
Spark plugs (petrol)
Engine oil (check + top-up)
Battery (check + top-up) if cap is removable
LEVEL Screen wash (check + top-up)
Coolant (check + top-up)
Brake fluid (check + top-up)
Power steering fluid (check + top up according to specification)
Operation of lights and indicators
Condition of glass, headlamp and light lenses and mirrors
Horn
Windscreen washer jets
Condition of wiper blades
Condition and tension of the ancillary drive belts
Handbrake
Condition of hydraulic circuits (hoses and covers) .
CHECK Condition of rubber boots and gaiters
Brake pads
Play in hubs, link rods, ball joints, flexible mountings
Shock absorbers .
Rear drum brake lining wear
Condition and pressure of tyres (including spare wheel)
Emission control check as per current legislation
Smoke opacity (diesel)
Passenger compartment filter (according to specification)
Visual check of the whole vehicle
SERVICE* Courtesy vehicle
ROAD TEST
29-09-2003 : All driving conditions : Arduous conditions * According to destination.
26
TRADE NAMES OF RECOMMENDED ENGINE LUBRICANTS IN EUROPE(1)
P E T R O L D I E S E L D I E S E L P E T R O L
(1) Minimum grade: Petrol engines ACEA A3 and API SH/SJ; Diesel engines: ACEA B3 and API CF/CD
ACEA = Association des Constructeurs Europens Automobiles (Association of European Automobile Manufacturers) -
API = American Petroleum Institute.
If oil is used which does not conform to the ACEA A3-B3 standards, this requires the "Arduous Conditions"
servicing schedule to be followed, which involves shorter intervals between services.
* This Fuel Economy oil can only be used in engines designed for its use.
Use 5W40 synthetic oil only for HDI Turbo Diesel engines fitted with a particulate emission filter.
29-09-2003
27
PEUGEOT SERVICING
Recommendations for
approved lubricants
The oils which appear in the table
opposite are suitable for most
purposes.
The diagram opposite states the
optimum range of viscosity
depending on the temperatures at
which the oils are to be used.
It is also possible to use "superior
quality" synthetic oils.
In the absence of semi-synthetic or
synthetic oils, oils of API SH/SJ
quality (for petrol engines), or CD/CF
quality (for diesel engines) may be
used by following the "Arduous
Conditions" servicing schedule,
which specifies shorter intervals.
Do not hesitate to ask for advice ONLY ONLY
from a PEUGEOT dealer to maintain Manual Gearbox ESSO Gear Oil BV TOTAL TRANSMISSION BV
driving pleasure and to minimise the 75W-80 PR 9736.41 75W-80 PR 9730.A2
maintenance cost of your vehicle.
For countries outside Europe, please ONLY
contact a local PEUGEOT dealer. Automatic ESSO ATF 4HP20-AL4
Gearbox PR 9736.22
Other recommended products
Power steering FLUIDE DA PR 9730.A1
Brake fluid PEUGEOT DOT4

Coolant ONLY PROCOR TM108/GLYSANTIN G33 or REVKOGEL 2000
Protection to minus 35 C
29-09-2003
28
INSTRUMENTS AND CONTROLS
13 - ABS warning light.

14 - Air bag warning light.
15 - Passenger air bag disarming
indicator light.
16 - Speedometer.
17 - Service indicator, oil
level and total distance
recorder.
18 - Trip recorder zero reset.
19 - Rear fog lamp indicator light.
20 - Electronic stability control
(ESP/ASR) warning light.
21 - Front fog lamps indicator
PETROL/DIESEL INSTRUMENT PANEL DIALS: MANUAL GEARBOX light.
1 - Rev counter. 22 - Diesel engine preheating

7 - Battery charge warning light.
light.
2 - Seat belt not fastened warning 8 - Central (STOP) warning
23 - Main beam headlamps indicator
light. light.
light.
3 - Engine diagnostics warning light. 9 - Engine oil pressure warning
24 - Low coolant level warning light
light.
4 - Handbrake and low brake (Diesel).
fluid level warning light. 10 - Low fuel level warning 25 - Dipped beam headlamps
light. indicator light.
5 - Left-hand direction
indicator. 11 - Right-hand direction 26 - Water in diesel filter warning
indicator. light (Diesel).
6 - Coolant temperature
indicator. 12 - Fuel gauge. 27 - Lighting rheostat.
29-09-2003
29
13 - ABS warning light.
14 - Air bag warning light.
15 - Passenger air bag disarming

indicator light.
16 - Speedometer.
17 -Service indicator, oil level and

total distance recorder.
18 - Trip recorder zero reset.
19 - Rear fog lamp indicator light.
20 - Electronic stability control

(ESP/ASR) warning light.
PETROL INSTRUMENT PANEL DIALS: AUTOMATIC GEARBOX 21 - Front fog lamps indicator light.
1 - Rev counter. 7 - Battery charge warning light. 22 - Main beam headlamps indicator
2 - Seat belt not fastened warning 8 - Central (STOP) warning light.
light. light. 23 - Dipped beam headlamps
3 - Engine diagnostics warning light. 9 - Engine oil pressure warning indicator light.
light.
4 - Handbrake and low brake fluid 24 - Lighting rheostat.
level warning light. 10 - Low fuel level warning
light. 25 - Sport programme indicator light.
5 - Left-hand direction
indicator. 11 - Right-hand direction 26 - Snow programme indicator
indicator. light.
6 - Coolant temperature
indicator. 12 - Fuel gauge. 27 - Gear lever position indicator.
29-09-2003
30
INSTRUMENTS AND CONTROLS Engine oil pressure Warning: Allow the engine to cool
warning light before topping up.
A permanently lit warning light or The cooling system is pressurised.
one that flashes with the engine Linked to the central STOP
running, indicates an operating warning light. To prevent the risk of scalding,
fault in the relevant unit. Some If it comes on with the engine run- unscrew the cap by two turns to allow
warning lights may be linked to ning, it is accompanied by an audible the pressure to drop.
buzzers and a message on the signal and the message ''Oil pres- Once the pressure has dropped,
multi-function display. Do not sure insufficient'' or ''Top up engine remove the cap and top up the level.
ignore this warning: contact a oil level'' on the multi-function dis- Contact a PEUGEOT dealer.
PEUGEOT dealer as soon as pos- play.
sible. If the Central STOP warning Stop immediately.
light comes on when you are driv-
ing, stop immediately where it is If there is a lack of oil in the lubrica-
safe to do so. tion circuit, top up the level.
Handbrake and
Contact a PEUGEOT dealer without low brake fluid
delay.
level warning
light
Linked to the central STOP warning light.
This comes on each time the ignition
is switched on.
Central STOP Diesel engine low
warning light coolant level Illumination of this light is accompa-
warning nied by an audible signal and a mes-
This light comes on light sage on the multi-function display
each time the ignition is indicating the cause of the warning:
switched on. Linked to the central STOP warning ''Handbrake on'', if the handbrake is
It is linked to the "engine oil pressure", light. applied or has not been released cor-
''coolant level low'', ''brake fluid This comes on for approximately rectly,
level'', "electronic brake force distri- 3 seconds each time the ignition is ''Brake fluid level low'' if there is an
bution fault" warning lights and the switched on. excessive drop in the brake fluid (if
coolant temperature gauge. This warning light is accompanied by the light remains on even with the
Stop immediately if it flashes with an audible signal and the message handbrake released),
the engine running. "Top up engine coolant level" on ''Braking fault'' is displayed simulta-
Contact a PEUGEOT dealer. the multi-function display. neously with the ABS light, indicating
Stop immediately. a malfunction of the electronic brake
force distribution.
Stop immediately.
Contact a PEUGEOT dealer.
29-09-2003
31
Battery charge Electronic stability To regenerate the filter, you are

warning light programme (ESP/ASR) advised to drive, as soon as possible
warning light when traffic conditions permit, at a
This comes on each time speed of 35 mph (60 km/h) or above
the ignition is switched on. This comes on for 3 sec- for at least five minutes (until the
If it comes on with the engine running, onds each time the ignition is warning light goes out).
it is accompanied by an audible signal switched on. If the warning light remains on, con-
and a message "Battery charge If the light remains on or comes on tact a PEUGEOT dealer.
fault" on the multi-function display. when the engine is running and the
It can indicate: vehicle is moving, it is accompanied Note: following prolonged operation
by an audible signal and the message of the vehicle at very low speed or at
faulty operation of the charging cir- ''ESP/ASR system not functioning'' idle, you may, in exceptional circum-
cuit, on the multi-function display; contact a stances, notice emissions of water
loose battery or starter terminals, PEUGEOT dealer. vapour at the exhaust on accelera-
When the engine is running and the tion. This does not have any effect
a cut or slack alternator belt, vehicle is moving, it flashes if the sys- on the vehicle's performance or on
tem is activated. the environment.
an alternator fault.
Contact a PEUGEOT dealer. It is lit continuously when the system If it flashes when the engine is run-
is disarmed. ning, accompanied by an audible
signal and the message ''Catalytic
converter fault'' on the multi-func-
tion display, it indicates a malfunction
Anti-lock braking Engine diagnostics in the injection or ignition system.
system (ABS) warning warning light There is a risk of damage to the cat-
light This comes on each time alytic converter (petrol engines only).
This light comes on for 3 the ignition is switched on. Contact a PEUGEOT dealer as soon
seconds each time the ignition is If it comes on with the engine running, as possible.
switched on. accompanied by an audible signal
If it remains on or comes on above 8 and the message on the multi-func-
mph (12 km/h), this indicates a mal- tion display:
function of the ABS. ''Antipollution fault'', it indicates a
However, the vehicle retains conven- malfunction in the emission control
tional servo-assisted braking. system.
Illumination of this light is accompa- ''Unblock diesel filter'' indicates
nied by an audible signal and the the start of saturation of the partic-
message ''ABS fault'' on the multi- ulate emission filter (due to excep-
function display. tionally prolonged urban driving
conditions: reduced speed, long
Contact a PEUGEOT dealer. traffic jams, ...).
29-09-2003
32
Diesel Passenger air bag Seat belt not

pre-heat disarmed indicator fastened warning
light light light
This comes on each time the ignition Illumination of this warning light is With the engine running, this indica-
is switched on. accompanied by an audible signal tor light comes on when the driver's
Wait until it goes out before trying the and the message "Passenger air bag seat belt is not fastened.
starter. deactivated" on the multi-function
display.
If the passager air bag is disarmed,
the indicator light comes on when
the ignition is switched on and
remains on.
In all cases, if the warning light flash-
es; contact a PEUGEOT dealer.
Water in diesel filter Air bag warning light Low fuel level
warning light warning
(according to country) This light comes on for a light
few seconds when the igni-
Illumination of this warning light is tion is switched on. The warning light comes on for three
accompanied by an audible signal Illumination of this warning light, with seconds when the ignition is
and the message ''Water in diesel the engine running, is accompanied switched on.
fuel filter'' on the multi-function dis- by an audible signal and the message When this light comes on with the
play. "Air bag fault" on the multi-function engine running, it is accompanied by
There is a risk of damage to the display indicating: an audible signal and the message
injection system. a fault in the front air bags, "Fuel level low" on the multi-func-
Contact a PEUGEOT dealer a soon or tion display.
as possible. a fault in the side air bags or cur- When the warning light comes on,
tain air bags. you have enough fuel to drive
Contact a PEUGEOT dealer. approximately 30 miles (50 km).
The tank capacity is approximately
60 litres.
This light flashes to indicate a mal-
function of the fuel gauge.
29-09-2003
33
Selector lever positions on the Automatic gearbox indicator

automatic gearbox display lights
Park "SPORT" indicator light

This comes on when the
"SPORT" programme on
the automatic gearbox is
Reverse selected.
"SNOW" indicator light

Coolant temperature Neutral
This comes on when the
indicator "SNOW" programme on the
When the needle is in zone A, the automatic gearbox is selected.
temperature is correct. Drive
When the needle is in zone B, the tem-
perature is too high. The central STOP
warning light flashes, accompanied by
an audible signal and the message
"Engine coolant temperature high" Manual mode: Operating fault
on the multi-function display. This is displayed when an
You must stop immediately. 1st gear engaged operating fault occurs, accom-
Warning: wait for the engine to cool panied by the message
before topping up the level. "Automatic gear fault" on the
multi-function display, an audi-
The cooling system is pressurised. 2nd gear engaged ble signal and flashing of the Sport and
In order to avoid any risk of scalding, Snow indicator lights on the instrument
unscrew the cap two turns to allow panel.
the pressure to drop.
When the pressure has dropped, 3rd gear engaged
remove the cap and top up the level.
4th gear engaged
29-09-2003
34
Instrument panel display Lighting

rheostat
After switching on the ignition, three functions are shown in succession:
service indicator (see corresponding section), With the lights on,
press the button to
engine oil level indicator, vary the intensity of
total distance recorder (total and trip distances). the lighting of the
Note: the total and trip distances are displayed for 30 seconds when the ignition instruments and con-
is switched off, on opening the driver's door, as well as on locking and unlocking trols. When the light-
the vehicle. ing reaches the minimum (or maxi-
mum) setting, release the button then
press it again to increase (or reduce)
Engine oil level indicator the brightness.
When the ignition is switched on, the engine oil level is indicated for approxi- As soon as the lighting is of the
mately 10 seconds, after the servicing information. required brightness, release the button.
Surplus oil
Flashing indicates a surplus of oil which can cause damage to the
engine.
If the surplus of oil is confirmed by checking using the dipstick,
contact a PEUGEOT dealer without delay.
Trip recorder
zero
No oil reset
Flashing indicates a lack of oil which can cause damage to the With the ignition on,
engine. press the button.
If the lack of oil is confirmed by checking using the dipstick, it is
essential to top up the level.
Oil level gauge fault

Check the oil level using the dipstick.
If the level is correct, the flashing indicates a true engine oil level
gauge fault.
The value obtained by checking the level using the dipstick is only correct if the
vehicle has been on level ground, with the engine off, for more than 10 minutes.
29-09-2003
35
YOUR 307 IN DETAIL
MULTI-FUNCTION Monochrome screen CT and

SCREENS colour screen DT
These two systems are controlled
Presentation by the RT3 GPS audio/telephone
keypad.
They enable the following informa-
tion to be displayed:
the time,
the date, Monochrome screen CT
the outside temperature (a mes-
sage warns you when there is a Main menu
risk of ice),
the audio source displays (radio,
Monochrome screen B CD, ...),
This enables the following information the telematic system displays
to be displayed: (telephone, services, ...),
the time, the status of the openings (doors,
the date, bonnet, ...),
the warning messages (e.g. "Fuel Press the RT3 audio/telephone
the outside temperature (the C level low") and vehicle functions "MENU" button to access the main
symbol flashes when there is a risk status messages (e.g. "Passenger menu and select one of the following
of ice), air bag deactivated") displayed applications:
the radio displays, temporarily, navigation - guidance (see section
the status of the openings (doors, the trip computer display (see cor- "Satellite navigation system"),
bonnet...), responding section),
audio (see "RT3 Audio/telephone"
the warning messages (e.g. the satellite navigation system dis- section),
"Battery charge fault") or plays (see corresponding section).
information messages (e.g. trip computer (see corresponding
"Passenger air bag deactivated") Note: to enable you to use all of your section),
displayed temporarily can be system's functions, you have two CD directory (see "RT3 audio/tele-
cleared by pressing button 1 or 2, ROMs: one, "Configuration", con- phone" section),
the trip computer (see corresponding tains the software and the various
section). display and spoken information lan- telematics (see "RT3 audio/tele-
guages, the other, "Navigation", con- phone" section),
tains the satellite navigation system configuration (see corresponding
map data. section).
29-09-2003
36
YOUR 307 IN DETAIL
telematics (see "RT3 audio/ Parameter configuration

telephone" section),
configuration (see corresponding
section),
map (see section "Satellite
navigation system"),
video (see corresponding
section).
Colour screen DT
A few definitions Monochrome screen B
General menu
Press button 1 for two seconds to
Superimposed display: gain access to the settings.
a window appears over the current Then, each press of this button
application for a short while, to permits scrolling of the various
announce a change of status of parameters.
another application. language of the information dis-
played,
Permanent application: unit of speed (km or miles),
main application currently in use, unit of temperature (degrees
displayed in the main screen Celsius or Fahrenheit),
window. time format (12 or 24 hours),
Press the RT3 audio/telephone hour,
"MENU" button to access the general
menu and select one of the following Contextual menu: minute,
applications: limited menu associated with the year,
navigation - guidance (see section main application currently in use, month,
"Satellite navigation system"), displayed in the main screen day.
window.
audio (see "RT3 audio/telephone" Pressing button 2 enables you to
section), change the parameter selected.
trip computer (see corresponding Continue pressing the button for
section), rapid scrolling.
directory (see "RT3 audio/ After ten seconds without action, the
telephone" section), screen returns to the usual display,
the modified data are recorded.
29-09-2003
37
YOUR 307 IN DETAIL
CT monochrome screen
The "Configuration" menu gives
access to the following parameters:
"Adjust the brightness": display
brightness setting. DT colour screen Video
"Sound": voice synthesiser setting The "Configuration" menu gives It is possible to connect video equip-
(for the masculine/feminine voice access to the following parameters: ment (a camcorder, digital camera, ...)
parameter: insert the configuration using the three video sockets situated
CD-Rom); setting of the spoken "Choose colours": selection from inside the glovebox.
commands, the palette of colours available for
display, It is only possible to display
"International parameters": choice video images when the vehicle is
"Adjust the brightness": display
of the language of the display, infor- brightness setting. stationary.
mation and spoken commands Select the "Video" menu from the
(German, English, Spanish, "Sound": voice synthesiser setting main menu:
French, Italian, Dutch, Portuguese: (for the masculine/feminine voice
parameter: insert the configuration "Display external video source" to
insert the configuration CD-Rom); activate/cancel the video function,
date and time setting (12 or 24 hour CD-Rom); setting of the spoken
mode, adjustment of the minutes on commands, "Video parameters" to adjust the
GPS); units setting (l/100 - C or display format, the brightness,
"International parameters": choice contrast and colour.
mpg - F). of the language of the display, Press "MODE" or "DARK" to exit
information and spoken commands video mode.
(German, English, Spanish,
French, Italian, Dutch, Portuguese: Successive presses on the "SOURCE"
insert the configuration CD-Rom); button allow you to select another audio
date and time setting (12 or 24 source other than the video.
hour mode, adjustment of the min-
utes on GPS); units setting (l/100 - For safety reasons, con-
C or mpg - F). figuration of the multi-
function screens by the
driver must be carried out
when stationary.
29-09-2003
38
YOUR 307 IN DETAIL
AUDIO RB3
Stalk movement Function

1 - Press (behind) Increase volume.
2 - Press (behind) Decrease volume.
1 + 2 - Simultaneous press Sound cut-off (mute); restoring of the sound by pressing any button.
3 - Press Automatic search of higher frequencies (radio) -
Selection of the next track (CD).
4 - Press Automatic search of lower frequencies (radio) -
Selection of the previous track (CD).
5 - Press the end Change of source (radio/cassette/CD changer).
6 - Rotation Selection of next station stored in the memory (radio) -
(clockwise) Selection of next CD.
7 - Rotation Selection of previous station stored in the memory (radio) -
(anti-clockwise) Selection of previous CD.
29-09-2003
39
YOUR 307 IN DETAIL
Button Function
A Radio on/off.
B Decrease volume.
C + Increase volume.
D RDS RDS function on/off.
Press for more than 2 seconds: regional following mode on/off.
E TA Traffic information priority on/off.
F Press fully: cassette rewind.
G Press fully: fast forward.
F+G j k Press half way: reversal of direction of play of the cassette.
jj kk Press fully: ejection of the cassette.
H
Selection of bass, treble, loudness, sound distribution and automatic
volume correction.
I Increase setting of functions associated with button H.
J Decrease setting of functions associated with button H.
K SRC Selection of source: radio, cassette or CD changer.
Press for more than 2 seconds: CD shuffle.
L kk Manual and automatic search of higher frequency.
Selection of next CD track and PTY (radio).
M MAN Manual/automatic operation of buttons L and N in radio mode.
N jj Manual and automatic search of lower frequency.
Selection of previous CD track and PTY (radio).
O BND Selection of FM1, FM2, FMast and AM wavebands.
AST Press for more than 2 seconds: automatic storing of stations in the memory (autostore).
1 to 6 123456 Selection of station stored in the memory.
Press for more than 2 seconds: storing of a station in the memory.
1 to 5 12345 Selection of a CD changer disc.
29-09-2003
40
YOUR 307 IN DETAIL
AUDIO RD3

1 + 2 - Simultaneous press Sound cut-off (mute); restoring of the sound by pressing any button.
3 - Press Automatic search of higher frequencies (radio) -
Selection of the next track (CD).
4 - Press Automatic search of lower frequencies (radio) -
Selection of the previous track (CD).
5 - Press the end Change of source (radio/CD/CD changer).
6 - Rotation Selection of next station stored in the memory (radio) -
(clockwise) Selection of following CD.
7 - Rotation Selection of previous station stored in the memory (radio) -
(anti-clockwise) Selection of previous CD.
29-09-2003
41
YOUR 307 IN DETAIL
Button Function
A Radio on/off.
B Decrease volume.
C + Increase volume.
D RDS RDS function on/off.
E TA Traffic information priority on/off.
Press for more than 2 seconds: PTY function on/off.
H
Selection of bass, treble, loudness, sound distribution and automatic
volume correction.
I Increase setting of functions associated with button H.
J Decrease setting of functions associated with button H.
L kk Manual and automatic search of higher frequency.
Selection of next CD track and PTY (radio).
M MAN Manual/automatic operation of buttons L and N.
N jj Manual and automatic search of lower frequency.
Selection of previous CD track and PTY (radio).
P CH. CD Selection of the CD changer.
Press for more than 2 seconds: shuffle.
Q CD Selection of the CD.
Press for more than 2 seconds: shuffle.
R Radio Selection of the radio. Selection of FM1, FM2, FMast, AM wavebands.
Press for more than 2 seconds: automatic storing of stations in the memory (autostore).
S i Ejection of the CD.
1 to 6 123456 Selection of station stored in the memory.
Press for more than 2 seconds: storing of a station in the memory.
1 to 5 12345 Selection of a CD changer disc.
29-09-2003
42
YOUR 307 IN DETAIL
GENERAL FUNCTIONS
On/off
With the ignition key in the accessories or ignition position, press button A to switch the set on or off.
The set can operate for 30 minutes without the vehicle ignition being switched on.
Anti-theft system
The audio system is coded in such a way that it can operate only on your vehicle. It would not function if fitted to another
vehicle.
The anti-theft system is automatic and requires no action on your part.
ADJUSTING THE VOLUME

Press button C to increase the volume, or button B to decrease it.
Continuous pressure on buttons C and B allows a gradual adjustment of the volume.
AUDIO SETTINGS
Press button H several times in succession to access the bass (BASS), treble (TREB), loudness (LOUD),
fader (FAD), balance (BAL) and automatic volume correction settings.
Exit from audio mode is automatic after a few seconds without pressing any button, or by pressing button H
after configuration of the automatic volume correction.
Note: bass, treble and loudness settings are specific to each source. It is possible to set them differently for
radio, cassette (RB3), CD (RD3) and CD changer.
29-09-2003
43
YOUR 307 IN DETAIL
Adjusting the bass

When "BASS" is displayed, press button I or J to vary the setting.
"BASS 9" for a minimum bass setting,
"BASS 0" for a normal setting,
"BASS +9" for a maximum bass setting.
Adjusting the treble

When "TREB" is displayed, press button I or J to vary the setting.
"TREB 9" for a minimum treble setting,
"TREB 0" for a normal setting,
"TREB +9" for a maximum treble setting.
Adjusting the loudness
This function automatically emphasises bass and treble tones. Press button I or J to switch the function on or off.
Adjusting the front/rear sound distribution (Fader)
When "FAD" is displayed, press button I or J.
Button I increases the volume in the front.
Button J increases the volume in the rear.
Adjusting the right/left sound distribution (Balance)
When "BAL" is displayed, press button I or J.
Button I increases the volume on the right-hand side.
Button J increases the volume on the left-hand side.
Automatic volume correction
This function enables the volume to be automatically adjusted depending on the level of noise produced by the speed of the
vehicle.
Press buttons I or J to switch the function on or off.
29-09-2003
44
YOUR 307 IN DETAIL
RADIO
Notes on radio reception
Your car radio is subject to phenomena which do not affect domestic radio sets. Both AM (MW/LW) and FM reception are
subject to various forms of interference. This is no reflection on the quality of the equipment, but is due to the nature of the
signals and the way in which they are transmitted.
On MW/LW, interference may be noticed when passing under high voltage power lines or bridges, or in tunnels.
On FM, interference may be the result of increasing distance from the transmitter, deflection of the signals by obstacles
(mountains, hills, buildings, etc.), or of being in an area which is not covered by a transmitter.
Selecting radio mode
Audio RB3: press the "SRC" button several times in succession.
Audio RD3: press button R.
Selecting a waveband
Audio RB3: briefly press the "BND/AST" button to select the FM1, FM2, FMast and AM wavebands.
Audio RD3: briefly press button R to select the FM1, FM2, FMast and AM wavebands.
Automatic station search

Briefly press button L or N to search for the station immediately above or below. By continuing to
press the button in the direction selected, you will obtain continuous scrolling of the frequency.
The scrolling stops at the first station found as soon as the button is released.
If the TA traffic programme is selected, only stations broadcasting this type of programme are selected.
Searching for a station occurs first in "LO" sensitivity (selection of the most powerful transmitters) during scanning of the
waveband, then in "DX" sensitivity (selection of the weakest and most distant transmitters).
To make a direct search in "DX" sensitivity, press button L or N twice.
29-09-2003
45
YOUR 307 IN DETAIL
Manual station search

Press the "MAN" button.
Briefly press button L or N to increase or decrease the frequency displayed.
By continuing to press the button in the direction selected, you will obtain continuous scrolling of the frequency.
The scrolling stops as soon as the button is released.
Pressing the "MAN" button again returns you to automatic station search.
Manual storing of stations in the memory

Select the station required.
Press one of the buttons "1" to "6" for more than two seconds.
The sound stops then becomes audible again, confirming that the station has been stored in the memory.
Automatic storing of FM stations in the memory (autostore)
Audio RB3: press and hold the "BND/AST" button for more than two seconds.
Audio RD3: press and hold button R for more than two seconds.
Your radio automatically stores the 6 stations with the strongest signal in FM. These stations are stored in the FMast
waveband.
If it is not possible to find 6 stations, the remaining memories are empty.
Recalling stations stored in the memory

For each waveband, briefly press buttons "1" to "6" to recall the corresponding station.
29-09-2003
46
YOUR 307 IN DETAIL
RDS
Using the RDS (Radio Data System) function on FM
Radio Data System allows you to continue listening to the same station, whatever frequency it is using for the region you are
going through.
Briefly press the "RDS" button to switch the function on or off.
The multi-function display will show:
"RDS" if the function is selected.
"(RDS)" if the function is selected but not available.
RDS station following

The display indicates the name of the station selected. The radio is continually searching for the station which has the best
reception and which is transmitting the same programme.
Traffic information programme

Press the "TA" button to switch the function on or off.
The multi-function display will show:
"TA" if the function is selected,
"(TA)" if the function is selected but not available.
Any traffic information flash will be given priority, whatever source you are listening to (radio, cassette or CD changer).
If you wish to interrupt a message, press the "TA" button; this switches the function off.
Note: the volume of traffic information announcements is independent of the volume of normal radio listening.
You can adjust it using the volume button. The setting will be stored and will be used when the next messages
are broadcast.
Regional following mode

When they are part of a network, certain stations broadcast regional programmes in the various areas they serve. With
regional following mode you can keep listening to the same programme.
Press the "RDS" button for more than two seconds to switch the function on or off.
29-09-2003
47
YOUR 307 IN DETAIL
PTY function: Audio RD3

This allows you to listen to stations broadcasting a specific type of programme (news, culture, sport, rock etc.).
With FM selected, press the "TA" button for two seconds to switch this function on or off.
To search for a PTY programme:

select the PTY function,
briefly press button L or N to scroll down the list of the various types of programmes offered.
when the programme of your choice is displayed, keep button L or N pressed for two seconds
to carry out an automatic search (after an automatic search the PTY function is switched off).
In PTY mode the different types of programmes can be stored in the memory. To do this, press the preselection buttons "1"
to "6" for two seconds. Briefly press the corresponding button to recall the type of programme stored in the memory.
EON system: Audio RD3

This connects stations which are part of the same network. It enables the broadcast of traffic information or a PTY pro-
gramme, by a station that is part of the same network as the station to which you are listening.
This service is available when you have selected the TA traffic information programme or the PTY function.
29-09-2003
48
YOUR 307 IN DETAIL
CASSETTE: AUDIO RB3

Selecting cassette mode
When a cassette is inserted, the cassette player will start automatically.
If a cassette is already inserted, press the "SRC" button until cassette mode is selected.
Note: before inserting the cassette, ensure that the tape is taut.
Ejecting the cassette

Fully press buttons F and G to eject the cassette from the player.
Direction of play
The player will play sides 1 and 2 of the cassette alternately, by automatically reversing the direction of play at the end of a
side.
To manually reverse the direction of play, press buttons F and G half-way.
Fast forward/rewind
Fully press button F or G to fast forward or rewind the cassette. At the end of the fast forward/rewind, the set plays the cur-
rent side.
Recommendations for using cassettes

Use good quality cassettes.
Avoid the use of cassettes which play for longer than 90 minutes.
Never expose the cassettes to heat or the direct rays of the sun.
Re-tighten the tape if necessary before inserting the cassette into the player.
Clean the playing head regularly with a damp-type cleaning cassette.
29-09-2003
49
YOUR 307 IN DETAIL
COMPACT DISC: AUDIO RD3

Selecting CD mode
After insertion of a disc, printed face upwards, the player starts automatically.
If a disc is already inserted, press button Q.
Ejection of a disc
Press button S to eject the disc from the player.
Selecting a track
Press button L to select the next track.
Press button N to return to the start of the current track or to select the previous track.
Accelerated play
Press and hold button L or N for forwards or backwards accelerated play.
Accelerated play stops as soon as the button is released.
Shuffle (RDM)
When the CD player is selected, press and hold button Q for two seconds. The tracks will be played in random sequence.
Pressing the button again for two seconds returns you to normal play.
Shuffle mode is de-activated each time the set is switched off.
The use of copied compact discs may cause faults.

Insert circular compact discs only.
29-09-2003
50
YOUR 307 IN DETAIL
CD CHANGER
Selecting CD changer mode
Audio RB3: press the "SRC" button several times in succession.
Audio RD3: press button P.
Selecting a disc
Press buttons "1" to "5" on the radio to select the corresponding disc.
Selecting a track
Press button L to select the next track.
Accelerated play
Press and hold button L or N for forwards or backwards accelerated play.
Shuffle (RDM)
When the CD changer is selected:
audio RB3: press and hold the "SRC" button for two seconds;
audio RD3: press and hold button P for two seconds.
The tracks will be played in random sequence. Pressing the button again for two seconds returns you to normal play.
29-09-2003
51
YOUR 307 IN DETAIL
GPS AUDIO/TELEPHONE RT3

1 + 2 - Press together Switch off sound (mute); restore sound by pressing any button.
3 - Press Automatic search of upper frequencies (radio) - Selection of next track (CD/CD changer)
Continuous pressure until release: fast forwards (CD/CD changer).
4 - Press Automatic search of lower frequencies (radio) - Selection of previous track (CD/CD chang-
er) Continuous pressure until release: rewind (CD/CD changer).
5 - Press end Change source (radio/CD/CD changer) - Confirmation of selection (on a menu or screen) -
Call connect/Call disconnect (Tel./incoming call - Call disconnect (Tel./Engaged).
Press for more than 2 seconds: display contextual menu (Tel./Not engaged).
6 - Rotation Selection of higher station stored in memory or storing in memory in position 1 for station not in
(clockwise) memory (radio) - Selection of following CD - Selection of following item on a menu or screen.
7 - Rotation Selection of lower station stored in memory or storing in memory in position 6 for station not
(anti-clockwise) in memory (radio) - Selection of previous CD - Selection of previous item on a menu or screen.
29-09-2003
52
YOUR 307 IN DETAIL

A Press: audio/telephone on/off.
Rotation: volume adjustment - Audio settings: sound ambience, bass, treble, loudness, fader (front/rear
balance), balance (left/right balance), automatic volume.
B Ejection of CD.
C SOURCE Selection of source: radio, CD, CD changer or Aux.
D Call connect (Tel./Incoming call) - Display contextual menu (Tel./Not engaged).
E Access "PEUGEOT" services menu.
Press for between 2 and 8 seconds: call "PEUGEOT Assistance" direct.
Press for more than 8 seconds: cancellation of the call made.
F MODE Change display.
Press for more than 2 seconds: display general information.
G Press: display contextual menu of display - Confirm inputting or adjustment.
Rotation: move within a menu - Select function/parameter - Adjust.
H Adjust higher frequency, step by step or continuous (long press).
Select previous CD (CD changer) - Movement on map (navigation).
I Adjust lower frequency, step by step or continuous (long press).
Select following CD (CD changer) - Movement on map (navigation).
J Infra-red window (IrDA)*.
K ESC Cancel current operation.
Press for more than 2 seconds: clear all superimposed displays and return
to permanent application.
L SIM card cover.
M kk Automatic search of higher frequency - Selection of following CD track.
Movement on map (navigation).
Double press: change from LO mode to DX mode.
Press for more than 2 seconds: CD accelerated forwards play.
29-09-2003
53
YOUR 307 IN DETAIL

N jj Automatic search of lower frequency - Selection of previous CD track.
Movement on map (navigation).
Double press: change from LO mode to DX mode.
Press for more than 2 seconds: CD accelerated backwards play.
O DARK 1st press: display top band (remainder of screen is black) - 2nd press: brightness removed (black
screen) - 3rd press: return to normal screen.
Press for more than 5 seconds: reinitialisation of the system.
P MENU Display general menu - Press for more than 2 seconds: display help screen and list
of voice commands.
Q Disconnect.
Press for more than 2 seconds: activation/deactivation of the transfer of the call to the voice mail or
to a call diversion number.
R BAND Select FM1, FM2, FMast, AM wavebands.
AST Press for more than 2 seconds: automatic storing of stations (autostore).
S TA/PTY Traffic information priority on/off.
Press for more than 2 seconds: PTY function on/off.
T RDS RDS function on/off.
U AUDIO Display window for adjusting sound ambience, bass, treble, loudness, sound distribution and automatic
correction of volume.
V SOS Press between 2 and 8 seconds: emergency call.
Press for more than 8 seconds: cancellation of the call made.
1 to 6 1 2 3 4 5 6 Select station in memory.
Press more than 2 seconds: store station being listened to in memory.
1 to 5 12345 Selection of CDs in the CD changer.
0 to 9* # 0 1 2 3 4 5 Alphanumeric keypad for entering text and telephone numbers.
6 7 8 9* #
* During the year.

29-09-2003
54
YOUR 307 IN DETAIL
GENERAL FUNCTIONS
On/off
With the ignition switch in the accessories position or with the ignition on, press button A to switch the audio
function of the RT3 audio/telephone on or off.
Note: in the absence of an ignition key, press button A to switch the telematics system on or off.
The RT3 GPS audio/telephone can operate for 30 minutes without switching the vehicle ignition on.
Notes:
the SIM card must be removed only after the audio/telephone has been switched off,
following automatic switching off of the audio/telephone after 30 minutes it is possible to make a telephone call by pres-
sing button D,
after the ignition has been switched off, the audio/telephone can be switched on again by pressing buttons D, E, V or by
inserting a CD in the player.
Anti-theft system
The RT3 GPS audio/telephone is coded in such a way that it can operate only on your vehicle. If fitting it to another vehicle,
consult your PEUGEOT dealer for configuration of the system.
The anti-theft system is automatic and requires no action on your part.
ADJUSTING THE VOLUME

Turn button A clockwise to increase the volume of the audio/telephone or anti-clockwise to decrease it.
Note: the volume setting is specific to each source. It is possible to have different settings for radio, CD or CD changer.
AUDIO SETTINGS
Press button U to access the Sound Ambience, Bass, Treble, Loudness, Fader (front/rear balance),
Balance (left/right balance) and Automatic volume adjustment settings windows.
Exit from audio mode is automatic after a few seconds without any action, or by pressing the "ESC" button.
Note: bass, treble and loudness settings are specific to each source. It is possible to have different settings
for radio, CD or CD changer.
29-09-2003
55
YOUR 307 IN DETAIL
Sound ambience
This function permits the selection of a "Linear", "Rock", "Classical", "Jazz", "Vocal" or "Techno" sound
ambience.
Turn button A to select the sound ambience.
Selecting "Linear" permits access to all of the settings defined below. Selecting another ambience sets the
bass and treble automatically.
Bass setting
When "Bass" is displayed, turn button A to vary the setting.
"9" for minimum bass setting
"0" for normal setting
"+9" for maximum bass setting
Treble setting
When 'Treble' is displayed, turn button A to vary the setting.
"9" for minimum treble setting
"0" for normal setting
"+9" for maximum treble setting
Adjusting the loudness
This function automatically emphasises bass and treble tones when the volume is low. Rotate button A to switch the func-
tion on or off.
Setting the front/rear sound distribution (Fader)
When "Fader" is displayed:
Turn button A clockwise to increase the volume in the front.
Turn button A anti-clockwise to increase the volume in the rear.
Setting the right/left sound distribution (Balance)
When "Balance" is displayed:
Turn button A clockwise to increase the volume on the right.
Turn button A anti-clockwise to increase the volume on the left.
Automatic volume adjustment "CAV"
This function allows the volume to be adjusted automatically depending on the level of noise produced by the speed of the vehicle.
Press button A to switch the function on or off.
29-09-2003
56
YOUR 307 IN DETAIL
RADIO
Notes on radio reception
Car radio/telephone receivers are subject to phenomena which do not affect domestic radio sets. Both MW/LW and FM are
subject to various forms of interference. This is not a reflection on the quality of the equipment, but is due to the nature of
the signals and the way in which they are transmitted.
On MW/LW interference may be noticed when passing under high voltage power lines or bridges, or in tunnels.
On FM, interference may be the result of the increasing distance from the transmitter, deflection of the signals by obstacles
(mountains, hills, buildings etc.) or of being in an area which is not covered by a transmitter.
Selecting the radio
Press "SOURCE" several times.
Selecting a waveband
Briefly pressing button "BAND/AST" to select the FM1, FM2, FMast and AM wavebands.
Automatic station search

Briefly press button M or N to search for the station immediately above or below.
The search stops at the first station found.
If the TA traffic programme is selected, only the most powerful stations broadcasting this type of pro-
gramme are selected.
Searching for a station occurs first in "LO" sensitivity (selection of the most powerful transmitters) for scanning of the wave-
band, then in "DX" sensitivity (selection of the weaker and more distant transmitters).
To make a direct search in "DX" sensitivity, briefly press button M or N twice.
29-09-2003
57
YOUR 307 IN DETAIL
Manual station search
Briefly press button H or I to increase or decrease the frequency displayed.

By continuing to press the button in the direction selected, you will obtain continuous scrolling of the frequency.
Scrolling stops at the first station found as soon as the button is released.
Manual station storing

Select the station required.
Press one of the buttons "1" to "6" for more than two seconds.
An audible signal is emitted, confirming that the station has been stored in the memory.
Automatic storing of FM stations in the memory
Press the ''BAND/AST'' button for more than two seconds.
Your audio/telephone automatically stores the 6 stations with the strongest signal in FM. These stations are stored in the
FMast waveband.
If it is not possible to find 6 stations, the remaining memories are empty.
Recalling stations stored in the memory

For each waveband, briefly press the buttons "1" to "6" to recall the corresponding stored station.
29-09-2003
58
YOUR 307 IN DETAIL
RDS SYSTEM
Using the RDS (Radio Data System) function on FM
Radio Data System allows you to continue listening to the same station, whatever frequency it is using for the region you are
going through.
Briefly press the "RDS" button to switch the function on or off.
The multi-function screen will show:
RDS if the function is active
RDS crossed out or greyed out if the function is active but not available.
RDS station following

This display indicates the name of the station selected. The audio/telephone is continuously searching for the station which
has the best reception and which is transmitting the same programme. This search may cause slight interference with the
transmission.
Traffic information programme
Press the ''TA/PTY'' button to switch the function on or off.
TA if the function is selected
TA crossed out or greyed out if the function is selected but not available.
Any traffic information flash will be given priority, whatever source you are listening to (radio, CD or CD changer).
If you wish to interrupt the broadcasting of a message, press the ''TA/PTY'' button.
Note: the volume of the traffic information is independent of the volume of normal radio/telephone listening.
You can adjust it by using the volume button. The setting will be stored and will be used when the next messages are broadcast.
Regional following mode (REG)

When they are part of a network, certain stations broadcast regional programmes in the various areas they serve. With
regional following mode you can keep listening to the same programme.
To do this, press the "RDS" button for more than two seconds to switch the function on or off.
REG if the function is active,
REG crossed out or greyed out if the function is active but not available.
29-09-2003
59
YOUR 307 IN DETAIL
PTY function
This allows you to listen to stations broadcasting a specific type of programme (news, culture, sport, rock etc.)
When FM is selected, press button "TA/PTY" for more than two seconds to switch the function or or off.
To find a PTY programme:

select the PTY button,
turn button G to scroll down the different types of programmes offered, then confirm your choice,
when the programme of your choice is displayed press button M or N to carry out an automatic search
(after an automatic search the PTY function is switched off if no station has been found).
In PTY mode the different types of programmes can be stored in the memory. To do this, press the preselection buttons "1"
to "6'' for more than two seconds. To recall the type of programme stored in the memory, briefly press the corrresponding
button.
EON system
This system connects stations which are part of the same network. It enables the broadcast of traffic information or a PTY
programme, by a station that is part of the same network as the station to which you are listening.
The service is available when you have selected the TA traffic information programme or the PTY function.
Audio menu
Select the "Audio" menu from the general menu to:
"Activate/Deactivate frequency following",
"Activate/Deactivate traffic info",
"Activate/Deactivate regional mode".
Contextual menu
By pressing knob G, the contextual menu allows you to access the following functions:
"Inputting a frequency"
"Display Radio Text" to display information connected with the station being listened
to, if "RT" is displayed permanently,
"List of stations" to access the 30 stations picked up locally directly,
"Refresh list" to update this list.
29-09-2003
60
YOUR 307 IN DETAIL
COMPACT DISC
Selecting CD mode
After inserting a disc, printed face upwards, the CD drive starts automatically.
If a disc has already been inserted, press the ''SOURCE'' button to select CD mode.
Ejecting a disc
Press button B to eject the disc from the drive.
Selecting a track
Press button M to select the following track.
Accelerated play
Press and hold button M or N for forwards or backwards accelerated play.
Contextual menu
By pressing knob G, the contextual menu permits you to switch on or switch off the
shuffle, track repeat, or play the start of a track, track programme and display tracks
played functions.
Do not use copied CDs as these could damage your player.

29-09-2003
61
YOUR 307 IN DETAIL
COMPACT DISC CHANGER

Selecting CD changer mode
Press the ''SOURCE'' button several times.
Selecting a disc
Press one of the buttons ''1'' to ''5'' on the audio/telephone to select the appropriate disc.
Buttons H and I allow you to select respectively the previous or following disc in the changer.
Selecting a track
Press button M to select the following track.
Accelerated play
Press and hold button M or N for forwards or backwards accelerated play.
Contextual menu
By pressing knob G, the contextual menu permits you to switch on or switch off the
shuffle, playing the start of a track or repeat a track and display tracks played functions.
29-09-2003
62
YOUR 307 IN DETAIL
TELEPHONE
This function is a GSM dual-band telephone (900 and 1 800 MHz) incorporated in the RT3 audio system.
It is a ''hands free'' telephone. This function is provided by a microphone located next to the front courtesy light, the speakers,
a steering column control and voice commands which allow access to most of the functions (the audio/telephone control
panel buttons allow access to all the functions).
Display of the principal ''mobile'' type functions, as well as consultation of the indexes, is provided by the multi-function
display.
This function is active, whatever position the ignition key is in even after thirty minutes, when the message ''Economy
mode active'' appears on the multi-function display.
Using the menus

Press the ''MENU'' button to display the general menu. Select the telematics application, validate "Telephone functions"
to access the principal telephone functions, then the various menus, in order to reach the one required.
This menu allows you to access the following functions:

Network: allows you to select the network search mode and to see the networks
available.
Duration of calls: allows you to consult the duration recorder of calls made and zero
re-set.
Security: allows you to use or modify the PIN code and to erase the list of calls and
mini-messages (SMS).
Telephone options: allows you to configure the calls with entering of my number,
automatic answering after X rings, specification of ring options and allows you to con-
figure the call diversion number.
Within each menu:
Move around and select a function by turning the G button then validate by pressing the button.
Cancel an operation using the ''ESC'' button.
29-09-2003
63
YOUR 307 IN DETAIL
Using the alphanumeric keypad

For a given button, to input a character in the second or subsequent rows press until you obtain the character required.
Buttons Associated characters
[1] 1 or space
[2] 2 or A B C 2 or a b c 2
[3] 3 or D E F 3 or d e f 3
[4] 4 or G H I 4 or g h i 4
[5] 5 or J K L 5 or j k l 5
[6] 6 or M N O 6 or m n o 6
[7] 7 or P Q R S 7 or p q r s 7
[8] 8 or T U V 8 or t u v 8
[9] 9 or W X Y Z 9 or w x y z 9
[0] 0 or + (long press)
[#] # or validation
[*] * or erasing of last character input (long press)
Installing the SIM card

Open flap L by pressing the point of a pencil on the circular opening above the flap.
Insert your Micro-SIM card, available from a mobile telephone operator, as indicated in the graphics, then close the flap.
Note: removal or insertion of the SIM card must only be carried out after the RT3 audio/telephone has been switched off.
29-09-2003
64
YOUR 307 IN DETAIL
Inputting the PIN code

Input your PIN code using the alphanumeric keypad and validate by pressing button G or but-
ton # to access the network. Connection to the network is validated by the appearance of a sym-
bol on the screen.
Warning: if you make three errors in succession when inputting your PIN code, your SIM card
will be blocked. To unblock it, you will need to input the PUK code. The PUK code will be sup-
plied to you by the person selling your SIM card (input of the PUK code allows for 10 errors in
succession; after this the SIM card becomes permanently unusable).
Note: the PIN code is required each time the ignition is switched on, unless the PIN code has
been stored in the memory or protection by PIN code is not activated on the SIM card.
Cancelling of PIN code request

In the menu ''Telephone functions'' select ''Security'', then ''Process the PIN code'', then validate the ''Cancel'' function.
Warning: in this case, do not lose your SIM card. Losing it would mean anyone who finds it would be able to make unlimited
calls.
Telephone function screens

Not in use
This screen indicates the presence of voice messages or mini-messages (SMS) not
listened to, the cumulatve time in use since the last zero reset and the status of your
telephone.
In use
This screen indicates the time elapsed since the start of the conversation, as well as
the number* or name of the person to whom you are speaking (if recorded in the index)
and the status of your telephone.
* If this option and service are available.

29-09-2003
65
YOUR 307 IN DETAIL
Making a call
Press button D to display the contextual menu of the telephone.
Note: pressing the end 5 of the steering column control for more than 2 seconds calls up
a contextual menu limited to the "Directory", "List of calls" and "Voice mail" functions.
Entering a number
Select the function ''Enter number'' then enter the number of the person you wish to speak to using the alphanumeric
keypad.
Press button D to make the call.
Making a call from a directory

Select the "Directory" function to access all the files containing a telephone number or the "List of calls" function to access
the list of the last twenty incoming (if the number display option is active) or outgoing calls.
Note: there are two directories, the RT3 audio/telephone directory and the SIM card directory. To consult the SIM directory,
insert your SIM card and enter your PIN code.
Receiving a call
When a ringing sounds to let you know that a call is waiting, you can choose either to accept it by pressing but-
ton D or the end of the steering wheel remote control or not to accept it by pressing the button Q or by selecting
and validating the "NO" button on the "Answer?" screen.
If you accept the call, to end your communication, press button Q.
If you do not accept the call, it is transferred to your voice mail or to a call diversion number.
You can activate or deactivate this transfer by pressing button Q for more than two seconds.
29-09-2003
66
YOUR 307 IN DETAIL
Text messages (SMS)

Accessing text messages
When the buzzer sounds (if the SMS text messages buzzer option is active) and a
superimposed screen announces "Do you wish to read the new text message
(SMS)?", you can choose to read the mini message received by selecting and valida-
ting "YES" or postpone reading it by selecting and validating "NO", by pressing the
"ESC" button or by waiting unti the announcement disappears.
Note: the old text messages stored and the new text messages, the reading of which you wished to postpone, can be con-
sulted. Press the "MENU" button then validate the telematic icon, select "Text messages (SMS)" and validate the function
"Reading of text messages received" by pressing button G. Then scroll through the list by turning the button and press
the button to select the mini message to be read.
Sending a text message

Note: Before typing your first text message, check that your text messages (SMS) cen-
tre number is stored correctly in the sub-menu "Server centre N". If it is not, any text
messages typed before this number is entered will not be sent.
In the menu "Text messages (SMS)" validate the function "Typing of a text message".
Type your text message using the alphanumeric keypad and validate it using the "OK"
button to store it or validate the "Send" button to send it. Validation of the "Send" but-
ton enables you to enter the number of your recipient or select it from the directory or from the list of calls and send the
message.
"Duration of calls" menu

Select the "Duration of calls" function from the "Telephone functions" menu to consult the duration counters for the calls
made. The partial counter totals the duration of the calls since the last zero reset carried out using the "Zero reset" button.
"Telephone options" menu

Select the "Telephone options" function from the "Telephone functions" menu to access the functions:
"Configure the calls" which permits activation and deactivation of the "show my number" and "automatic answering after
X rings" functions
"Ringing options" which permits adjustment of the ringing volume for voice calls, activation of the mini messages (SMS)
receipt buzzer and selection of a ring tone from the five offered.
"Diversion number/voice mail" which permits recording of the call diversion number chosen by the customer, otherwise
the call will be transferred to the voice mail.
29-09-2003
67
YOUR 307 IN DETAIL
Services*
Press button E to display the "Services" menu and select one of the following services:
"Customer Contact Centre" which enables you to contact the PEUGEOT Customer Contact Centre directly
and access the services offered (this type of call is suspended if an emergency or breakown call is made).
"PEUGEOT Assistance" which enables you to contact the call centre which controls the PEUGEOT breakdown
service directly and receive rapid assistance (you have 6 seconds within which to cancel the call when it is made).
During the breakdown call phase it is not possible to make any other calls with the exception of emergency calls.
If you have signed the specific PEUGEOT contract, your call will be located.
"Operator services" which gives access to the list of services specific to your operator (e.g.: customer service, con-
sumption monitoring, news, stock market, weather, travel, games, etc) if they are available.
Emergency call*
In an emergency, press button V until a signal is heard and a call validation/deletion screen is displayed (delay of
6 seconds) or enter 112 directly.
Make an emergency call if you are involved in an situation which leads you to fear serious consequences (injuries, ...)
for those who are exposed to it (if you witness or are involved in an accident resulting in injuries, an attack, ...).
Before making a call of this kind, the audio/telephone must detect a cellular network.
If you have not signed the specific PEUGEOT contract, the parameters of the SOS button are set so that a call is made to
112 - unique number made available by the worldwide GSM network, reserved for emergency calls.
No security mode is required and, depending on the network, you do not need to insert your SIM card or enter your PIN.
If you have signed the specific PEUGEOT contract, your call will be located and you will be put in contact with a PEUGEOT
assistance team.
For further details, refer to the general conditions of your contract.
"PEUGEOT Assistance"/Emergency call

During a connection to "PEUGEOT Assistance" or an emergency call, it is not possible to send or receive calls or SMS
messages; these will be transferred to your voice mail.
In this case, a green diode flashes on the RT3 audio/telephone panel, when the emergency call or "PEUGEOT Assistance"
call procedure begins, then lights continuously when the call is taken by the services concerned.
* If option and service available.
29-09-2003
68
YOUR 307 IN DETAIL
The Directory
General
The "Directory" application gives access to 400 files divided into 4 independent sub-directories ("User1", "User2", "User3"
and "User4"). It enables you to manage these files, make calls using the SIM card and activate guidance.
Main menu
From the general menu, select the "Directory" application to access its main menu
and select one of the following functions:
"Call", to call a number stored in a file,
"Activate guidance to", to initiate guidance to a location stored in a file,
"Management of directory files", to add, delete, modify and consult directory files or
exchange them with the SIM card,
"Directory configuration", to select the working directory and define the directory when
the system is switched on.
Creation/Modification of a file
To create a file, from the "Directory" menu, select the function "Management of direc-
tory files" then "Add".
On the file select the section to be filled in, validate then enter the information.
To modify an existing file, select it using the "Consult or modify the file" function of the
"Management of directory files" menu then make the modifications.
Note: when the address is entered, the navigation CD-Rom must be present in order to obtain guidance to this destination.
29-09-2003
69
YOUR 307 IN DETAIL
Description of a directory file

When a description is linked to a directory file, you can record the description vocally so that it can be used subsequently for
direct access by voice commands (e.g.: "Call" "[Name of the voice description]" or "Guide to" "[Name of the voice
description]").
Select "Consult or modify the file" from the "Management of directory files" menu to access the screen which permits ente-
ring and recording of the description.
Press the record button and follow the instructions.
TMC (Traffic Message Channel) RDS Traffic Information

You can access information regarding the traffic conditions from the "Telematics" menu, then from the "TMC RDS Traffic
Information" function (see section "Satellite navigation system").
29-09-2003
70
YOUR 307 IN DETAIL
Voice commands
The voice commands make it possible to use pre-recorded words or phrases to control a certain number of functions of the
RT3 audio/telephone.
Activation of the voice commands
Press the button on the end of the lights stalk to activate or deactivate this function.
Example: to recall the radio station stored on button 3, the key words are: "Radio" "Memory" "3".
To use these key words, you must say the word "Radio", wait for the audible confirmation signal, then say the word "Memory",
wait for the audible confirmation signal, then end with the word "3", wait for the audible confirmation signal which will carry
out the action requested.
Notes:
between two key words, a screen indicates the time remaining and the key word recognised,
in the absence of any voice commands, this function will be switched off after approximately five seconds,
if a command is not understood, the system transmits "Pardon" and displays "Word not recognised" on the screen.
Saying the phrase "Help" or "What can I say" displays all of the commands available on the screen.
List of commands available
For the radio, say "RADIO", then:
"PREVIOUS"/"FOLLOWING"/"MEMORY" + 1...6/"AUTOSTORE"
For the CD, say "CD PLAYER", then:
" PREVIOUS TRACK"/"FOLLOWING TRACK"/"TRACK NUMBER" + 1...20/"SHUFFLE"/"SCAN"/"REPEAT"
For the CD changer, say "CD CHANGER", then:
" PREVIOUS TRACK"/"FOLLOWING TRACK"/"TRACK NUMBER" + 1...20/"PREVIOUS DISC"/"FOLLOWING DISC"/
"DISC NUMBER" + 1...5/"SHUFFLE"/"SCAN"/"REPEAT"
For the telephone, say "TELEPHONE", then:
"LAST NUMBER"/"DIRECTORY" + DESCRIPTION/"SERVICES"
For navigation, say "NAVIGATION", then:
"STOP"/"RE-START"/"DIRECTORY" + DESCRIPTION
To change the permanent application, say "DISPLAY", then:
"AUDIO"/"TELEPHONE"/"NAVIGATION"/"TRIP COMPUTER"
To call someone recorded in the directory directly, say "CALL" + DESCRIPTION
To be guided to the address of someone recorded in the directory, say "GUIDE TO" + DESCRIPTION.
Various:
"CANCEL"/"HELP"/"WHAT CAN I SAY".
29-09-2003
71
YOUR 307 IN DETAIL
CD CHANGER
This is located in the centre of the fascia under the radio. It holds up to
5 discs.
To load the changer, insert the discs with the printed side upwards.
To remove a disc, press and hold one of the buttons "1" to "5".
The use of copied compact discs may cause faults.

29-09-2003
72
YOUR 307 IN DETAIL
SATELLITE NAVIGATION The CD-Rom drive

SYSTEM
This is part of the RT3 GPS audio/telephone.
Introduction
The satellite navigation system
guides you, by means of vocal and
visual instructions (graphics), to
your chosen destination.
The heart of the system lies in the
use of a map data base and GPS 1. Ejection button on CD-Rom.
(Global Positioning System). With 2. CD-Rom housing.
this system you can fix the position
of your vehicle by means of a satel- The navigation CD-Rom
lite network.
The system uses the following
elements:
the CD-Rom drive,
the configuration CD-Rom,
the navigation CD-Rom,
This contains all the map data.
the last voice message recall It must be inserted in the drive, printed face upwards.
control, Use only CD-Roms approved by PEUGEOT.
the control keypad,
the CT monochrome screen or the
DT colour screen. The last voice message recall control.
Certain functions or services

described may vary depending
on the version of CD-Rom or the
country where the vehicle is sold.
For safety reasons, the

inputting of navigation Pressing for more than two seconds on the button at the end of the lights stalk
information by the driver repeats the last voice information.
must be carried out when
the vehicle is stationary.
29-09-2003
73
YOUR 307 IN DETAIL
The control keypad Rotation of the dial:

This allows you to move round the screen and thus select a function.
It also allows you:
with a "setting" type parameter, after selection, to increase or decrease the
value,
with a "list" type parameter, to open the list and scroll through the values.
with map guidance, to increase the zoom.
Pressing the dial:

This allows:
access to the list of controls (contextual menu) of the permanent display, if
there is no other display superimposed.
This lets you select and validate the confirmation of the selected function or the modified value.
functions, controls and programmes selection of a "setting" or "list" type parameter for modification.
displayed.
"MODE" button:
brief press: modification of permanent display (audio system, navigation/
guidance...),
Press for more than two second: display of general information.
"ESC" button:
brief press: cancelling of operation in progress or erasing of last
superimposed display.
pressing for more than two seconds: erasing of all superimposed displays and
return to the permanent display.
"MENU" button:
Brief press: access to the general menu.
Press for more than two seconds: access to the help menu.
29-09-2003
74
YOUR 307 IN DETAIL
General notes on the display General menu

Switch on the RT3 GPS audio/
Monochrome screen CT Colour screen DT telephone and insert the navigation
CD-Rom.
Press the "MENU" button to access
the general menu.
1 2 1 2 3
3
4
7 6 5 7 6 5 4
During guidance, if the navigation CD-Rom is present, the screen displays

different information depending on the manoeuvres to be carried out.
1. Current manoeuvre or compass or course (if calculation in progress or zone
not mapped).
2. Next manoeuvre to be carried out.
Select the Navigation/Guidance icon
3. Next road to be taken. using the dial G, then validate by
4. Current road. pressing the dial to access the main
5. Estimated time of arrival at destination. "Navigation - Guidance" menu.
6. Distance to final destination.
7. Distance to next manoeuvre.
Notes:
depending on the situation of the vehicle and on the reception of GPS
information, this information may disappear from the screen temporarily,
during guidance, the navigation CD-Rom must remain in the RT3 GPS
audio/telephone.
29-09-2003
75
YOUR 307 IN DETAIL
Navigation - Guidance Selecting a destination Entering an address
The main "Navigation - Guidance" The "Select a destination" menu The last guidance address is displayed.
menu offers various options for activa- offers various options for reaching a
tion or management of guidance: destination: Select and validate in succession the
entry zones "Town", "Street", then
choice of the type of destination entering a postal address, "N" to fill them in.
address (entering of address, service, selecting a service available in a
GPS co-ordinates, stored address), town (town hall, hotel, cinema, The "OK" function permits validation
modification to the initial route airport...), of the address and access to the
(entering of a diversion), guidance activation function.
entering GPS details,
displaying of the chosen destination, selecting a destination stored in The "Archive" function permits
setting of the guidance option the directory, recording of the address in a directory
parameters, file.
selecting one of the last ten desti-
stop or resume guidance (displaying nations. The "Current location" function
of the message which changes permits display of the current
depending on the previous status). address.
29-09-2003
76
YOUR 307 IN DETAIL
Entering the name of the town When the list contains fewer than Entering the number of the street
five names, these are displayed auto- or junction
matically. Select a town then validate
by pressing the dial.
When the complete name of the
town is displayed, select the "OK"
function then confirm by pressing the
dial.
Note: once the town has been
entered, you can confirm by pressing
"OK". You will then be guided to the
centre of this town automatically.
Entering the name of the street

Enter the name of the street in the
To enter the name of a town, select same way as the name of the town. Enter the number of the street pre-
each letter by turning the dial, then viously entered.
validate each letter by pressing the When the full name of the street is Select the "OK" function, then
dial. displayed, select the "OK" function confirm by pressing the dial.
then confirm by pressing the dial.
If an error is made entering the letters, Note: if the number of the street
the "Correct" function permits erasing entered is not available, it is rejected.
of the last letter entered. You can also select a street from the
Note: following the validation of a "Junctions" function, which avoids
Entering the town and street having to enter the street number.
letter, only those which could make using the alphanumeric keypad
up a name existing in the database Note: if the street selected does not
appear. Press the numeric key which corre- have a number, the list of junctions is
As letters are entered, the "List" sponds to the letter required until the displayed automatically.
function indicates the number of letter appears on the screen, then The full destination is displayed.
towns beginning with the same confirm by pressing the # key after Select the "OK" function, then
letters. Activation of this function each letter. confirm by pressing the dial to
permits selection of a town from the access the guidance activation
list. function. Follow the instructions
given by the system.
29-09-2003
77
YOUR 307 IN DETAIL
Selecting a service Note: if the service selected is not avail- GPS details
able in the programmed location, a
If you wish to be directed to a service, temporary message informs you of this.
select the category corresponding
to the service, then confirm by Following validation of the location,
pressing the dial. the service closest to it is displayed.
The list of services corresponding to The distance indicated is the distance
the category selected is displayed. as the crow flies from the service to
the selected location.
Select the service then confirm by
pressing the dial to access the
"Place choice" function.
The most recent destinations are shown.

There are three possible methods of
defining the location to which you
wish to travel:
accept the last details input by
means of the "OK" function,
input the details of your destination,
An indication on the edge of the screen
(x/n) shows you the maximum number of automatically input the details of
establishments providing the same ser- your current location by means of
vice within a radius of 30 miles (50 km), as the "Current location" function.
The last address entered is displayed.
There are three options for defining the the crow flies, from the selected location.
location in which you wish to obtain this Use buttons "<" and ">" to consult the
service: list provided.
accept the last address entered When the establishment of your
using the "OK" function, choice is displayed, you can:
fill in the "Town" and "Street" zones, select the "OK" function to acti-
automatically enter the name of vate guidance towards this service,
your current location using the
"Current location" function. select the "Archive" function to enter
this establishment in your directo-
29-09-2003 ry.
78
YOUR 307 IN DETAIL
Selecting a destination stored in Selection of one of the last ten Changing the initial route
the directory destinations
Select the ''Directory'' function to Select the "Most recent destina- Activate the function ''Changing the
access the file in which the address tions" function to access one of the route'', then input the distance
you are looking for is archived. last twenty addresses stored. involved in the change required.
Select a description by scrolling Select a description by scrolling Select the ''OK'' function then vali-
down the list by means of the dial, down the list by means of the dial, date by pressing the dial.
then confirm by pressing the dial. then confirm it by pressing the dial. The system calculates the change
The directory file is then displayed. The complete address is then dis- which is closest to the value input
Select the "OK" function, then press played. and gives you the option of whether
the dial to access the guidance Select the "OK" function, then press or not to use this change.
activation function. the dial to access the guidance
Follow the directions given by the activation function.
system. Follow the instructions given by Details of the route
the system. You can consult the destination
address at any time by activating the
"Chosen destination" function on
the "Navigation - Guidance" menu.
29-09-2003
79
YOUR 307 IN DETAIL
Guidance options Calculation criteria Management of the directory
This function enables you to rename

an address stored in the directory.
Select the description corresponding
to the stored address to be changed.
Select the "Rename" function, then
confirm by pressing the dial.
Select the "OK" function, then confirm
by pressing the dial to record the
changes made.
Stopping/Resuming guidance
The menu ''Guidance options'' The last criterion used is displayed. "Stop guidance"
provides access to the following Select a criterion from the list, then During guidance, select this function
functions: validate by pressing the dial. then validate.
changing of the route calculation When the criterion of your choice "Resume guidance"
criteria, has been selected, select the "OK" In the absence of guidance, select
voice synthesis adjustment of function then confirm by pressing the this function then validate to activate
guidance messages, dial. guidance to the last destination
description of the information programmed.
relating to the navigation CD-Rom, Adjusting the voice synthesiser
management of the addresses Note: after re-starting the engine, a
Select the type of voice "male" or screen appears enabling you to
stored in the directory. "female", after inserting the configu- resume guidance activated before
ration CD-Rom. the ignition was switched off.
Adjust the volume of the voice synthesis
by turning the dial, then validate by
pressing the dial.
Note: the volume can also be adjusted
during a message, using the audio/
telephone button or the steering
wheel control.
29-09-2003
80
YOUR 307 IN DETAIL
"Navigation - Guidance" TMC (Traffic Message Channel)
contextual menu RDS Traffic Information
This function enables you to receive
messages regarding the traffic
conditions (accidents, traffic jams,
weather, ...).
They may appear temporarily as a
superimposed display or be read by
the voice synthesiser, if it is active.
In map mode*, special TMC symbols
are displayed depending on the type
of information.
Select the "TMS RDS Traffic Informa-
tion" function on the "Telematics"
menu, you can choose:
"Consult the messages",
"Filter the TMC info":
The contextual menu associated with
the "Navigation - Guidance" application in relation to a route, if guidance
appears as a superimposed display, is in progress,
when this is the application currently in in relation to a type of event,
use in the main screen window. around a location and/or the vehicle,
This menu is limited to the following "Voice synthesiser",
functions:
changing of the initial route (entering "Activate/Deactivate traffic info".
of a diversion),
switching to "Selection-Movement
on map" mode*,
storing of the current location
(postal address if available or, if it
is not, the GPS co-ordinates),
changing of the route calculation
criteria,
stopping or resuming of guidance
(displaying of the message which
changes depending on the previ-
ous status). * DT colour screen only.
29-09-2003
81
YOUR 307 IN DETAIL
General notes on the "Map" A "Zoom" function enables you to "Selection-Movement on map"
application* enlarge the map, in accordance with mode
the thirteen preset levels relating to
The "Map" application has two the following scales:
display modes:
50 m/cm, 100 m/cm, 150 m/cm,
"Vehicle following on map" 200 m/cm, 500 m/cm,
mode, representing active guid-
ance on the map on the right and a 1 km/cm, 2 km/cm, 5 km/cm,
large-scale view of the next inter- 10 km/cm, 20 km/cm, 50 km/cm,
section on the left, 100 km/cm, 200 km/cm.
"Selection-Movement on map" This is achieved by turning the dial.
mode, representing consultation of
the map on the right and a compass
on the left. This mode permits:
selection of any point on the map
To switch from one mode to the "Vehicle following on map" mode to obtain guidance towards it or to
other, press the dial on the right obtain information about it (postal
briefly, then select the "Move the address if available or, if it is not,
map" or "Exit map mode" function. GPS co-ordinates),
In "Selection-movement on map" movement on the map by means
mode, you can see symbols, repre- of the four directional arrows, rep-
senting the various types of services resenting the four cardinal points
which exist, sorted by category: (North, East, South, West),
"Administration and safety" symbol zooming in on the map in accor-
on a grey background, dance with the thirteen preset lev-
"Hotels, bars and restaurants" els,
symbol on a yellow background, displaying of the "Map" contextual
This mode permits: menu.
"Other businesses" symbol on a
purple background, displaying of the vehicle on the
map with the route proposed by
"Culture, tourism and entertainment" the navigation if the guidance is
symbol on a white background, active,
"Sports centres and open air centres" zooming in on the map in accor-
symbol on a green background, dance with the thirteen preset lev-
"Transporation and automobiles" els,
symbol on a blue background. displaying of the "Navigation -
Guidance" contextual menu. * DT colour screen only.
29-09-2003
82
YOUR 307 IN DETAIL
Map "Map" contextual menu
From the general menu, the main The contextual menu associated with
"Map" menu offers various options the "Map" application and with the
for guidance management: "Selection-Movement on map"
switching to "Selection-Movement mode appears as a superimposed dis-
on map" mode, play, when these are in use in the
main screen window.
direction of the map towards the
North or in the direction of the vehicle, This menu is limited to the following
recentering of the map around the functions:
vehicle, displaying of the information on the
opening of the services selection location selected on the map,
window visible on the map, such selection of a location on the map
as hotels, service stations, etc. as a destination,
displaying of the window for ente- storing of the location selected
ring the description for recording (postal address if available or, if it
the current position of the vehicle is not, GPS co-ordinates, so that
in a directory file. they can be recorded in a directory
file),
switching to "Vehicle following on
map" mode.
29-09-2003
84
YOUR 307 IN DETAIL
29-09-2003
85
YOUR 307 IN DETAIL
VENTILATION
1. Windscreen de-icing or demisting vents.

2. Front window de-icing or demisting vents.
3. Side vents.
4. Centre vents.
5. Air outlet to front footwells.
6. Air outlet to rear footwells.
Advice on operation
Place the air flow control at a level sufficient to ensure a good renewal of air in the passenger compartment.
The ''OFF'' position cuts off all the air circulation in the passenger compartment.
Note: only use the ''OFF'' position occasionally (risk of condensation).
For perfectly even air distribution, take care not to obstruct the exterior air intake grilles, the vents and the air ducts under
the front seats, as well as the air extractor located in the boot. Check that the passenger compartment filter is in good
condition.
29-09-2003
86
YOUR 307 IN DETAIL
HEATING/VENTILATION
1. Temperature adjustment 2. Air distribution adjustment Place air intake control button 4 in
the ''Outside Air'' position, (button
4 released, indicator light off),
To be adjusted to your requirements. Windscreen and side win- Place the temperature and air flow
dows (de-icing/demisting). controls to maximum,
Close the centre vents.
To quickly de-ice or demist the wind-
screen and side windows:
29-09-2003
87
YOUR 307 IN DETAIL
4. Air intake 5. Demisting the rear screen and

Windscreen, side windows exterior mirrors
and footwells.
Pressing button 4 permits
recirculation of the interior With the engine running,
air. Recirculation, indicated pressing the button once
Footwells. by illumination of the indica- demists the rear screen
tor light, prevents exterior and the mirrors.
odours and smoke from entering the This switches off automati-
passenger compartment. cally after approximately twelve min-
utes.
Centre and side As soon as possible, switch button 4 Pressing again activates demisting
vents. to the outside air position to prevent for a further twelve minutes.
misting of the windows and deterio- It is possible to stop demisting by
ration of the air quality. The indicator pressing the button again before the
light switches off. end of the twelve minutes.
3. Air flow adjustment
Turn the control from posi-

tion 1 to position 4 to obtain
an air flow sufficient to
ensure your comfort.
29-09-2003
88
YOUR 307 IN DETAIL
AIR CONDITIONING
1. Air conditioning control The air conditioning does not 2. Temperature adjustment
operate while the air flow
The air conditioning is designed to adjustment control is in the "OFF" To be adjusted to your requirements.
operate in all seasons. In summer, it position.
enables the temperature to be
lowered and in winter, above 0 C, it Note: It is quite normal that the
increases the effectiveness of the condensation created by the air
demisting. conditioning results in a flow of water
under the vehicle when it is
stationary.
Press the switch, the indi-
cator light comes on.
29-09-2003
89
YOUR 307 IN DETAIL
3. Air distribution adjustment 4. Air flow adjustment 6. Demisting the rear screen and
the mirrors
Windscreen and side win- Turn the control from posi-
dows (de-icing/demisting) tion 1 to position 4 to obtain With the engine running,
an air flow sufficient to pressing the button once
ensure your comfort. demists the rear screen
and the mirrors.
To quickly de-ice or demist the wind-
screen and side windows: This switches off automatically after
5. Air intake approximately twelve minutes.
Place the temperature and air flow Pressing again activates demisting
controls to maximum, for a further twelve minutes.
Close the centre vents, Pressing button 5 permits It is possible to stop demisting by
recirculation of the interior pressing the button again before the
Switch air intake button 5 to the air. Recirculation, indicated
"Outside Air" position (button 5 end of the twelve minutes.
by illumination of the
released, indicator light off), indicator light, prevents exterior
Start the air conditioning by pres- odours and smoke from entering the Important precaution
sing the A/C button. passenger compartment.
Operate the air conditioning system
Used simultaneously with the air for 5 to 10 minutes, once or twice a
conditioning, recirculation enables month, to keep it in perfect working
cooling performance to be improved. order.
Used in a humid climate, If the system does not produce cold
recirculation may result in misting of air, do not use it and contact a
Windscreen, side windows the windows. PEUGEOT dealer.
and footwells. As soon as possible, switch button 5
to the outside air position, to prevent
deterioration of the air quality. The
Footwells. indicator light switches off.
Centre and side vents.
29-09-2003
90
YOUR 307 IN DETAIL
AUTOMATIC AIR CONDITIONING
Automatic operation
1. Temperature adjustment 2. Automatic comfort programme 3. Automatic visibility programme

The chosen temperature Press the AUTO button. The sys- In some cases, the automatic
is displayed. Press the up tem automatically adjusts the comfort programme may not
and down arrows to atmosphere inside the vehicle in be sufficient for de-icing or
change it. A setting accordance with the temperature demisting of the windows
around 21 C enables a that you have chosen. To do this, it controls (humidity, several passen-
comfortable temperature the temperature, the flow, the distribution and gers, ice etc.). Select this programme
to be obtained. the intake of air as well as the air conditioning. to clear the windows quickly.
Note: for your comfort, the settings are retained To exit this programme and return to
between two start-ups of your vehicle if the the automatic comfort programme,
temperature in the passenger compartment press the AUTO button.
has not changed significantly; otherwise,
operation resumes in automatic mode.
29-09-2003
91
YOUR 307 IN DETAIL
Manual operation the windscreen (de-icing or 8. Switching the system off

demisting),
If you wish, you can make a different the windscreen and the footwells,
choice from that offered by the The OFF button enables
system by changing a setting. The the footwells, the entire system to be
other functions will still be controlled the centre and side vents and the switched off.
automatically. Pressing the AUTO footwells, Temperature-related com-
button returns the system to the centre and side vents. fort is no longer guaranteed but a
completely automatic operation. slight flow of air is maintained to
avoid condensation and renew the
air.
Pressing the OFF, AUTO, or visibili-
4. Air conditioning 6. Air flow ty button again reactivates the sys-
tem with the values set before it was
The flow of air can be switched off.
Press this button to stop air
cooling. The symbol ECO is increased or reduced Note: if you wish to cut off the flow of
displayed. Automatic oper- by pressing buttons + air completely, press the air intake but-
ation of the air conditioning or respectively. ton 7.
is resumed when the button is
pressed again. The symbol A/C is 9. Demisting the rear screen and
displayed. 7. Air intake the mirrors
Notes Press this button to demist

Press this button for recircu- the rear screen and the
It is quite normal that the condensa- lation of the interior air. mirrors. Demisting switches
tion created by the air conditioning Recirculation, shown on the off automatically. It is
results in a flow of water under the display, enables the pas- possible to stop operation of the
vehicle when it is stationary. senger compartment to be insulated demisting before it is switched off
To prevent condensation on the from exterior odours and smoke. automatically by pressing the button
inside of the vehicle in cold or wet again.
weather, you are advised to avoid Avoid prolonged recirculation of interior
using the ECO mode. air. To do this, press the button again to
resume automatic management of the Important precaution
intake of air. Operate the air conditioning for 5 to
Note: To prevent condensation on the 10 minutes, once or twice a month, to
5. Air distribution keep it in good working order.
inside of the vehicle in cold or wet
weather, you are advised to avoid If the system does not produce cold
Pressing this button several air, do not use it and contact your
times in succession using this mode.
PEUGEOT dealer.
enables the air flow to be
directed in turn towards:
29-09-2003
92
YOUR 307 IN DETAIL
FRONT SEATS
1- Forwards-backwards
adjustment
Lift the control and slide the seat for-
wards or backwards.
2- Access to rear seats (3 door)
Pull the handle to fold the seat back
and move the seat forwards. On
repositioning, the seat returns to its
initial position.
Note: it is also possible to use con-
trol 3. Then adjust the angle.
Warning: no person or object must
prevent the seat slide from returning
to its initial position; return to this
position is necessary for the seat to
lock in place.
3- Seat back angle adjustment
Push the handle towards the rear.
29-09-2003
93
YOUR 307 IN DETAIL
4- Driver's or passenger's seat 7- Head restraint height and 8- Storage drawers

height adjustment angle adjustment
There is a storage drawer under
Pull the handle upwards or push it To raise or lower the restraint, pull it each front seat.
downwards as many times as neces- forwards, sliding it at the same time.
sary to obtain the required position. To open it, lift it and pull.
To take it out, open it to its full
5- Heated seats switch extent, press the ends of the slides
The adjustment is correct when and lift it, then remove it completely.
With the engine running, press the the upper edge of the head
switch. The temperature is controlled To put it back in place, with it fully
restraint is level with the top of closed, press on the top of the
automatically. the head. drawer to secure it.
Pressing the switch again stops Do not place heavy objects in the
operation. drawers.
Note: the command for activation of To remove the head restraint, place it
heating of the seat(s) remains memo- almost in the top position, lift the lug Under the front passenger seat, the
rised for two minutes after the igni- using a coin and pull it forwards and layout of the floor allows for storage
tion has been switched off. upwards at the same time. of a first aid kit and a warning trian-
To put it back in position, locate the gle (small version).
6- Armrests stems of the restraint in the holes,
taking care to keep them in line with
These can be folded down and are the seat back.
removable.
REAR HEAD RESTRAINTS
To remove them, press the button Active seat back (front seats)
located between the armrest and the These have a high position for when
side of the seat and pull it. This possesses a device to prevent
"whiplash". they are in use and a low position for
when they are stored.
When there is an impact from the
rear, the action of the body on the The head restraints can also be
seat back forces the head restraint removed.
forwards and upwards, preventing To remove them, pull upwards as far
the head being thrown backwards. as the stop then press the lug.
Never drive with the head

restraints removed; they
must be in place and cor-
rectly adjusted.
29-09-2003
94
YOUR 307 IN DETAIL
REAR SEATS (SALOON) Rear armrest

(saloon and estate)
To fold down the rear left seat (2/3 part)
or the right seat (1/3 part), always start Lower the armrest to access the
with the seat, never with the seat storage shelf on the seat back.
back (risk of damage): Lift the lid. It contains a storage
move the front seat(s) forward if tray as well as two cup holders and
necessary, two pen holders.
lift the front of the seat cushion 1,
tilt the seat cushion 1 against the
front seat(s),
check that the seat belt is correctly
positioned on the side of the seat
back, When repositioning:
pull control 2 forwards to unlock fold up the seat back and lock it
the seat back 3, (the red marker of control 2 should
place the head restraints in the low no longer be visible),
position, fold up the seat.
fold down the seat back 3. Take care not to trap the seat belts
Note: the seat cushion 1 can be and to position the stalks correctly.
removed to increase the volume of
the load space.
Squeeze the seat cushion fixings to
detach them from their fastenings.
29-09-2003
95
YOUR 307 IN DETAIL
REAR SEATS (ESTATE) Removing the seat cushion

(position against the front
Folding the seats: seats):
To fold the rear left seat (2/3 section) Take hold of the seat cushion 1 at the
or the rear right seat (1/3 section), bottom to remove it from its fixings
always start with the seat cushion, and pull upwards.
never with the seat back (risk of
damage):
move the front seat(s) forward if Refitting the seat cushion
necessary, (position against the front
pull the handle A located between seats):
the seat cushion 1 and the seat Fit the seat cushion 1 in its fixings,
back 3 forwards, then pull it
upwards to lift the seat cushion pull control 2 forwards to release To lock it, press on the top of the
and tilt it against the front seat(s), the seat back 3, seat cushion 1.
check that the seat belt is posi- place the head restraints in the low
tioned correctly on the side of the position, Putting the seats back
seat back, tilt the seat back 3. in position:
Note: the seat cushion 1 can be fold the seat back and lock it (the
removed to increase the volume of red indicator on control 2 should
the load space. no longer be visible),
fold the seat cushion.
Take care not to trap the seat belts
and to position the stalks correctly.
29-09-2003
96
YOUR 307 IN DETAIL
GENERAL POINTS RELATING TO CHILD SEATS Rules for transporting children

on the front passenger seat**
Although one of PEUGEOT's main criteria when designing your vehicle, the safe-
ty of your children also depends on you.
For maximum safety, please follow these precautions: Children under the age of 10 must
not travel in the forwards facing
position, unless the rear seats are
Since 1992, all children under the age of 10 must travel in approved child already occupied by other children
seats* suited to their weight, on seats fitted with a seat belt. or the rear seats cannot be used
(absent or folded). In this case,
adjust the front passenger seat to
A child weighing less than 9 kg must travel in the rearwards facing position the intermediate position and leave
both in the front and in the rear. PEUGEOT recommends that children the passenger air bag armed.
should travel in the "rearwards facing" position up to the age of two.
The transportation of children in the
rearwards facing position is permit-
Statistically, the safest seats in your vehicle for the transportation of ted. In this position, it is essential to
children are the rear seats. disarm the passenger air bag.
PEUGEOT recommends that children travel in the rear even when a Otherwise, the child would risk being
"rearwards facing" child seat is used. killed or seriously injured if the air
bag were to inflate.
If a child is travelling on a booster seat, check that the lap section of the seat
belt passes over the child's thighs correctly. The chest section of the seat belt
must be positioned on the child's shoulder without touching the neck.
PEUGEOT recommends that you use a booster seat with a back, fitted with a
seat belt guide.
Remember to fasten the seat belt or the child seat harness keeping the slack
in relation to the child's body to a minimum, even for short journeys.
* According to current legislation in the country.

** Consult the relevant administration in your country for information regarding
the rules for transporting children on the front passenger seat.
29-09-2003
97
YOUR 307 IN DETAIL
This seat can also be used on seats

not fitted with ISOFIX mountings. In
this case, it is compulsory to attach
it to the vehicle's seat by means of
the three-point seat belt.
Refer to the "Summary table for fit-
ting child seats".
Follow the instructions for fitting

the child seat in the seat manu-
facturer's instruction booklet.
"ISOFIX" MOUNTINGS The ISOFIX KIDDY* child seat

The two rear side seats of your vehi- It can be fitted in the "rear facing"
cle are fitted with ISOFIX moun- position from birth to 13 kg and in the
tings. These are two rings located "forwards facing" position from 9 to
between the seat back and the seat 18 kg.
cushion. In the rear, in the "forwards facing"
The ISOFIX child seats are fitted position, it is imperative that the front
with two locks which are secured seat is in the mid-way position on the
easily on these rings. runner, seat back upright.
Fitting a child seat in a vehicle incor- In the "rear facing" position, the body
rectly compromises the child's pro- of the child seat must be in contact
tection in the event of a collision. with the back of the corresponding
This ISOFIX mounting system guar- front seat.
antees reliable, safe and fast fitting
of the child seat in your vehicle.
For information regarding the
ISOFIX child seats approved for your
vehicle, contact your PEUGEOT
dealer.
* You can only fit ISOFIX child seats
approved by PEUGEOT on your
vehicle's ISOFIX mountings.
29-09-2003
98
YOUR 307 IN DETAIL
CHILD SEATS RECOMMENDED BY PEUGEOT

In addition to the ISOFIX child seats, PEUGEOT offers a complete range of child seats which are secured using the seat
belt.
These child seats have been assessed in impact conditions in PEUGEOT vehicles and guarantee optimum safety for your
children:
Group 0+: from birth to 13 kg

L1 - "Britax Babysure": installed in the rear-facing position using a three-point seat belt.
In the front, it is compulsory to disarm the passenger air bag.
Group 1: from 9 to 18 kg
L2 - "Rmer Prince": installed using a two or three-point seat belt.
For the safety of your child, the seat and the restraining cushion must never be separated.
Group 2: from 15 to 25 kg
L3 - "Rmer Vario'': installed with a two or three-point seat belt.
29-09-2003
99
YOUR 307 IN DETAIL
Never leave one or more

children alone and unsu-
pervised in a vehicle.
Never leave a child or an
animal in a vehicle which is
exposed to the sun and has the
windows closed.
To protect your young children
from the sun, fit blinds on the rear
windows.
Groups 2 and 3: from 15 to 36 kg

L4 - ''Recaro Start'': installed with a three-point seat belt.
The height and width of the seat back and length of the seat cushion must
be adjusted according to the age and build of your child.
L5 - "Klippan Optima": installed with a three-point seat belt.

From the age of 6 years (approximately 22 kg), the booster is used on its own.
Refer to the "Summary table for the installation of child seats".

Never leave the keys within reach
Disarm the passenger air bag when installing a "rearwards facing" child of children inside the vehicle.
seat on the front passenger seat. Otherwise, the child would risk being Observe strictly the recommenda-
killed or seriously injured were the air bag to inflate. tions for assembling and securing
the child seat as shown in the
child seat instructions.
To prevent the doors from opening
accidentally, use the child lock*.
Also, do not open the rear win-
dows more than a third*.
* According to model.
29-09-2003
100
YOUR 307 IN DETAIL
SUMMARY TABLE FOR FITTING CHILD SEATS

In accordance with the European regulation (Directive 2000/3), the table below indicates the extent to which each seat in
your vehicle can be fitted with a child seat secured using the seat belt and universally approved (child seat which can be
installed in any vehicle using the seat belt) for one or more weight groups:
Statutory weight group
Seat Groups 0 (a) and 0+ Group 1 Group 2 Group 3
< 13 kg 9 - 18 kg 15 - 25 kg 22 - 36 kg
Front passenger (b) U U U U

Fixed seat L1, L6 L2, L7 L3, L4, L5 L4, L5
Front passenger (b) U (R) U (R) U (R) U (R)
Height adjustable seat (R) L1, L6 L2, L7 L3, L4, L5 L4, L5
Rear seat U U U U
Side L1, L6 L2, L7 L3, L4, L5 L4, L5
Rear seat L1 (c) X L3, L4, L5 L4, L5
Centre
U : seat suitable for the installation of a universal "rear facing" child seat and a universal "forwards facing" child seat.
U (R) : seat suitable for the installation of a universal "rear facing" and "forwards facing" child seat. The vehicle seat must
be adjusted to the highest position.
X : no child restraint.
According to destination:
L1 : BRITAX Babysure E11 0344117 Universal (birth to 13 kg).
L2 : RMER Prince E1 03301058 Universal (9 to18 kg).
L3 : RMER Vario E1 03301120 Universal (15 to 25 kg).
L4 : RECARO Start E1 03301108 Universal (15 to 36 kg).
L5 : KLIPPAN Optima E17 030007 Universal (15 to 36 kg).
L6 : KIDDY Isofix Rearwards facing (d) E1 03301123 and Universal (birth to 13 kg).
L7 : KIDDY Isofix Forwards facing (d) E2 030011 Universal (9 to 18 kg).
(a) Group 0: from birth to 10 kg.
(b) The rules for transporting children in the front passenger seat are specific to each country. Consult the current legislation in your country.
(c) (seat belt under seat body).
(d) Child seat secured using the seat belt in the absence of Isofix mountings. See section "Seats - Isofix mountings" for use
of the KIDDY child seat on the vehicle's Isofix mountings.
29-09-2003
101
YOUR 307 IN DETAIL
Pre-tensioning and force-

limiting front seat belts To be effective, a seat belt
must be tightened as close
Safety in the event of a frontal impact to the body as possible.
has been improved by the introduc- Depending on the nature
tion of pre-tensioning and force-limit- and the seriousness of the impact,
ing front seat belts. Depending on the pre-tensioners may be trig-
the seriousness of the impact, the gered before and independently of
pre-tensioning system instantly tigh- the air bags.
tens the seat belt firmly against the In all cases of an air bag being
body of the occupant. triggered, the air bag warning light
The pre-tensioning seat belts are on the instrument panel comes on.
armed when the ignition is on. After an impact, have the system
The force-limiting device reduces the checked by a PEUGEOT dealer.
pressure of the seat belt against the
body of the occupant in the event of
an accident.
Rear seat belts

The three rear seats are all fitted with
three-point inertia reel seat belts.
SEAT BELTS The side seats are fitted with force-
limiting devices.
To adjust the height of the
front seat belts
To lower the attachment point,
squeeze control 1 and slide it
downwards.
To raise the attachment point,
squeeze control 1 and slide it
upwards.
To lock the seat belts
Pull the strap, then insert the
buckle into the stalk.
29-09-2003
102
YOUR 307 IN DETAIL
THE KEYS The remote control Unlocking

Locking Press button B to unlock the vehicle.
The keys allow you to switch on the
ignition and operate the passenger Press button A to lock the vehicle. This is confirmed by rapid flashing of
air bag disarming switch as well as to the direction indicators.
This is confirmed by fixed lighting of
independently operate the locks on the direction indicators for approxi- Note: if the vehicle is locked and
the front doors, the fuel filler cap and mately two seconds. unlocking is activated inadvertently,
the glove box. unless the doors are opened within
Note: if the vehicle is locked and 30 seconds, the vehicle will lock
unlocking is activated inadvertently, automatically.
Central locking unless the doors are opened within
30 seconds, the vehicle will lock
From the driver's door, the keys automatically.
allow you to lock, deadlock and
unlock the doors and tailgate, as well
as fold back the exterior mirrors. Vehicles fitted with deadlocking
Locating your vehicle
If one of the doors or the boot is Warning: deadlocking renders the
open, the central locking does not internal and external door locking To locate your vehicle, if you have
work; an audible signal indicates this controls inoperative. locked it, in a car park:
when locking by remote control. Pressing button A deadlocks the press button A, the courtesy lights
vehicle. come on and the direction indica-
The remote control performs the tors flash for a few seconds.
same functions at a distance. the direction indicators for approxi-
mately two seconds.
Note: a long press on button A, in
addition to deadlocking, automatical-
ly closes the windows and the sun-
roof.
A second press on button A within
five seconds of deadlocking changes
this to normal locking.
the direction indicators for approxi-
mately two seconds.
29-09-2003
103
YOUR 307 IN DETAIL
ELECTRONIC ENGINE
IMMOBILISER
This locks the engine control system
as soon as the ignition has been
switched off and therefore prevents
starting of the vehicle by anyone
who does not have the key.
The ignition key has an electronic
chip which has a special code.
When the ignition is switched on, the
code must be recognised for starting
to be possible.
Changing the battery of the
Confidential card remote control
If the system does not function
correctly, the central locking button The confidential card contains the Warning that the battery is flat is
indicator light, situated in the centre identification code necessary for any given by an audible signal accom-
of the fascia, flashes rapidly when work carried out by a PEUGEOT panied by the message ''Remote
the ignition is switched on (2nd dealer on the system. This code is control battery low'' on the multi-
notch), accompanied by an audible hidden by a film, which should be function display.
signal and the message "Anti-theft removed only if necessary. To replace the battery, remove the
device faulty" on the multi-function Keep your card in a safe place, screw then unclip the casing using a
display. never inside the vehicle. coin at the ring (CR 2016/3 volt battery).
In this case your vehicle will not If the remote control does not work
start. after the battery has been changed,
reprogramme the remote control.
Contact a PEUGEOT dealer as
soon as possible. Key in ignition
A buzzer sounds on opening the dri- Programming the remote
ver's door, if the key has been left in control
the ignition.
Switch off the ignition.
Switch the ignition on again.
Immediately press button A.
Switch off the ignition and
remove the remote control key
from the ignition lock. The remote
control is now working again.
29-09-2003
104
YOUR 307 IN DETAIL
Make a careful note of the number on each key. The key number is coded on the label attached to the key.
If the keys are lost, your PEUGEOT dealer can rapidly supply you with new keys.
The high frequency remote control is a sensitive system; do not operate it while it is in your pocket as there is a
possibility that it may unlock your vehicle, without you being aware of it.
The remote control does not operate when the key is in the ignition, even when the ignition is switched off, except for
reprogramming.
Do not operate the deadlocking function if there is anyone inside the vehicle.
Driving with the doors locked may make access to the passenger compartment by the emergency services more difficult
in an emergency.
As a safety precaution (with children on board), remove the ignition key when you leave the vehicle, even for a short time.
Do not repeatedly press the button of your remote control out of range of your vehicle. You run the risk of stopping it from
working and the remote control would have to be reprogrammed.
When purchasing a second-hand vehicle:

ensure that you are given the confidential card;
have the key codes memorised by a PEUGEOT dealer, to ensure that the keys in your possession are the only ones
which can start the vehicle.
Do not make any modifications to the electronic engine immobiliser system.
29-09-2003
105
YOUR 307 IN DETAIL
When the alarm is triggered, the Set the alarm by locking or dead-
siren sounds and the direction indi- locking using the remote control
cator lights flash for thirty seconds. (button A indicator light flashes
After triggering, the alarm remains once a second).
set. Note: when the alarm is set but the
Warning: if the alarm has been trig- remote control does not operate:
gered ten times in succession, on the Unlock the doors with the key
eleventh time it becomes inactive. and open the door. The alarm is
Note: if button A indicator light flashes triggered.
rapidly, the alarm has been triggered Switch on the ignition. The alarm
while you were away from your vehi- is disarmed.
THE ALARM cle.
Disarming Incorrect operation

This provides two types of protection:
exterior protection: it sounds if When the ignition is switched on, if
Unlock the vehicle with the remote button A lights for ten seconds, there
a door, the boot or the bonnet is control key (button A indicator light
opened. is a fault in the siren connection.
goes out).
Contact a PEUGEOT dealer to have
interior protection: it sounds if Note: if the alarm has been triggered the system checked.
the volume inside the passenger while you were away from your vehi-
compartment changes (breaking cle, the rapid flashing of the indicator
of a window or a movement light will stop when you switch on the
inside the vehicle). ignition. Automatic activation*
The alarm is activated automatically
Setting the alarm To set the alarm with exterior two minutes after the last closure of
Switch off the ignition and get out
protection only a door or the boot.
of the vehicle. If, while you are away from the vehi- In order to avoid accidental triggering
Set the alarm by locking or dead- cle, you wish to leave a window par- of the alarm when a door or the boot
locking using the remote control tially open or a pet inside the vehicle, is opened, it is essential to first press
(button A indicator light flashes you should choose exterior protec- the unlocking button on the remote
once per second). tion only. control.
Note: if you wish to lock your vehicle Switch off the ignition,
without setting the alarm, use the In the next ten seconds, press
door lock. button A until the indicator light is
on continuously,
Get out of the vehicle,
* According to destination.
29-09-2003
106
YOUR 307 IN DETAIL
THE DOORS
Locking/Unlocking from
Opening the doors from the inside
outside Press button A.
This allows locking or unlocking of Child safety
the doors and the tailgate. This prevents either of the rear doors
Note: if the vehicle is deadlocked, being opened from inside.
button A does not function. In this
case use the remote control for Turn the switch a quarter of a
unlocking. turn using the ignition key.
"Door open" alert

With the engine running, an audible
signal and a diagram locating the
door briefly displayed on the multi-
Opening the doors from inside function display warn you that a door
The front door opening controls per- is not properly closed.
mit complete unlocking of the vehicle. In addition, if the vehicle is moving,
However, the rear door opening con- the courtesy lights flash.
trols only unlock the door concerned.
Note: the door opening controls do
not function when the vehicle is
deadlocked.
29-09-2003
107
YOUR 307 IN DETAIL
Note: the tailgate locks automati-

cally when the vehicle is being driven
at 6 mph (10 km/h) and unlocks
when one of the doors is opened if
the speed is below 6 mph (10 km/h).
"Tailgate open" warning

When the engine is running, an audi-
ble signal and a diagram displayed
briefly on the multi-function screen
warn you that the tailgate is not pro-
perly closed.
Saloon In addition, if the vehicle is being
driven, the courtesy lights flash. Tailgate release
This enables the tailgate to be
unlocked in the event of a central
locking fault.
Fold back the rear seats to gain
access to the lock from inside the
boot,
Insert a small screwdriver into hole A
of the lock to unlock the tailgate.
Estate
TAILGATE
Simultaneous locking or unlocking
of the tailgate and the doors
The tailgate is locked or unlocked by
the remote control or the driver's
door lock.
To open, pull handle A and lift the
tailgate.
29-09-2003
108
YOUR 307 IN DETAIL
Notes:
Always remove the key
After reconnecting the battery, in the from the ignition when
event of a malfunction, you must leaving the vehicle, even
reinitialise the safety auto-reverse. for a short time.
place the control in the maximum In the event of contact during
partial opening position (3rd notch operation of the roof, you must
to the right), reverse the movement of the roof.
wait until the roof is in the maxi- To do this, press the switch con-
mum partially open position, cerned.
press the control for at least one When the driver operates the roof
second. switch, he must ensure that no
THE SUNROOF In the event of unwanted opening of one is preventing correct closing
the roof on closing (for example, in of the roof.
to partially open the roof: Turn the presence of ice), and immediate- The driver must ensure that the
the switch to the right (three possi- ly after the roof stops: passengers use the sunroof cor-
ble settings). move the control to the "O" posi- rectly.
to open the roof completely: tion and press the control imme- Be aware of children when ope-
Turn the switch to the left (six pos- diately, rating the roof.
sible settings). continue to press the control until
to close it completely: Turn the the roof is fully closed.
switch back to position "O". The safety auto-reverse function
safety auto-reverse: When the is not active during these opera-
sunroof is closing and meets an tions.
obstacle, it stops then partially
opens again.
The sunroof shutter is manual.
29-09-2003
109
YOUR 307 IN DETAIL
"Bonnet open" warning Flashing of the warning light indi-

cates a malfunction of the fuel
With the engine running or the vehi- gauge.
cle moving, flashing of the central
"STOP" warning light accompanied Contact a PEUGEOT dealer.
by an audible signal and a diagram The engine must be switched off
on the multi-function display, warns when filling with fuel.
you that the bonnet is not properly Open the fuel filler flap.
closed.
Insert the key then turn it to the
left.
Remove the cap and hang it on
the hook located on the inside of
the flap.
A label affixed to the inside of the fuel
OPENING THE BONNET filler flap indicates which type of fuel
to use.
From inside: push the handle on the When you fill your tank, do not con-
left-hand side under the fascia. tinue after the third cut-off of the
From outside: lift the catch and pump. This could cause your vehicle
raise the bonnet. to malfunction.
The capacity of the tank is approxi-
mately 60 litres.
Bonnet strut After filling the tank, lock the cap
Secure the strut to hold the bonnet and close the fuel filler flap.
open.
Before closing the bonnet, replace
the strut in its housing. FILLING WITH FUEL
To close
Lower the bonnet and release it at Low fuel level
the end of its travel. Check that the
bonnet is properly locked. When the minimum fuel
level in the tank is
reached, this warning
light comes on.
You can still drive approximately
30 miles (50 km).
29-09-2003
110
YOUR 307 IN DETAIL
Dipped/Main beam change Vehicles fitted with front fog

Pull the stalk towards you. lamps and a rear fog lamp (ring C)
Note: with the ignition off, when the
driver's door is opened, a buzzer Front fog lamps (first rota-
sounds if you have left your lights on. tion of the ring forwards)
Front fog lamps and rear fog These operate with the side lights
lamp and the dipped headlamps.
Rotate the ring forwards to switch on When the main beam headlamps
and backwards to switch off. The sta- are switched on, the front fog lamps
tus is confirmed by the indicator light are switched off. They are switched
on the instrument panel. on again when the main beam head-
THE LIGHTS STALK lamps are switched off.
Front and rear lights Front and rear fog

Selection is by turning ring A. lamps (2nd rotation of
the ring forwards)
Vehicles fitted with a rear fog lamp
(ring B)
Note: to switch off the rear fog lamp
and the front fog lamps, turn the ring
Lights off Rear fog lamp backwards twice in succession.
Note: when the lights are switched
off automatically or when the dipped
Side lights This only operates with the dipped/ headlamps are switched off manual-
main beam headlamps. ly, the front fog lamps, the rear fog
Note: when the lights are switched lamp and the side lights will remain
off automatically, the rear fog lamp on (turn the ring backwards to switch
Dipped/main beam and the dipped headlamps will
headlamps off the front fog lamps. The side
remain on (turn the ring backwards lights will then be switched off).
to switch off the rear fog lamp. The
dipped headlamps and side lights
Automatic switching will then be switched off).
on of lights
29-09-2003
111
YOUR 307 IN DETAIL
"Follow me home" lighting AUTOMATIC SWITCHING ON Operating check

In poor light or at night, if you leave OF LIGHTS Activation
your vehicle, the side lights and
dipped headlamps can be left on for The side lights and dipped beam Activation of this function is accom-
approximately one minute. headlamps switch on automatically if panied by an audible signal and the
the light is poor and when the wind- message "Automatic lighting
To do this: screen wipers operate continuously.
place the key in the STOP position, active" on the multi-function display.
place the lights stalk in position 0, They switch off when the light
becomes bright enough or the wind-
"flash" the headlamps, screen wipers are switched off. Disarming
get out of the vehicle and lock it.
This function is active when the vehicle Disarming of the function is accom-
is supplied to the customer. panied by an audible signal.
To disarm or activate the function: Note: the function is temporarily disar-
med when the driver uses the manual
Turn the key to the accessories lighting controls.
position (1st notch), If the brightness sensor does not
Press the end of the lights stalk for function correctly, the system acti-
In good or rainy weather, more than four seconds. vates the function (the lights come
both day and night, the Note: In foggy weather or in snow, on). The driver is alerted by an audi-
front fog lamps and the rear the brightness sensor can detect suf- ble signal, accompanied by the mes-
fog lamp are dazzling and ficient light. As a result, the lights will sage "Automatic switching on of
are prohibited. not come on automatically. lights faulty" on the multi-function
Do not forget to switch them off display.
when they are no longer needed. Contact a PEUGEOT dealer to have
The brightness sensor, coupled the system checked.
with the rain sensor, is located in
the centre of the windscreen,
behind the interior mirror. It is
used for automatic switching on
of the lights.
Direction indicators (flashers)
Left: downwards.
Right: upwards.
29-09-2003
112
YOUR 307 IN DETAIL
After the ignition has been

switched off, if the stalk was in a
wipe position, you must reactivate
this function:
move the stalk to any position,
then move it back to the required
position.
Special position of the front

windscreen wiper
In the minute following switching off
of the ignition, any action on the stalk
positions the wipers in the centre of
WINDSCREEN WIPER STALK the windscreen.
This action enables you to position the
Front windscreen wiper with Front windscreen wiper with wiper blades for winter parking, clean-
intermittent wipe automatic wipe ing or replacement (See section
"Practical information - Changing a
2 Fast wipe 2 Fast wipe wiper blade").
(heavy rain). (heavy rain).
To park the wipers after this has been
1 Normal wipe 1 Normal wipe done, switch on the ignition and oper-
(moderate rain). (moderate rain). ate the stalk.
I Intermittent wipe. AUTO Automatic wipe.
0 Off. 0 Off. Windscreen and headlamp wash
Single wipe Single wipe Pull the windscreen wiper stalk towards
(press downwards). (press downwards). you. The windscreen wash then the
windscreen wipers operate for a fixed
period.
In the Intermittent position, the wip- In the AUTO position, the wiping
ing speed is in proportion to the vehi- speed is in proportion to the intensity The windscreen wash and head-
cle speed. of the rainfall. lamp wash operate simultaneously
for two seconds, only if the head-
lamps are on.
29-09-2003
113
YOUR 307 IN DETAIL
Automatic timed windscreen Rear windscreen wiper

wipers Do not cover the rain sen-
sor located on the wind-
In the AUTO position, the windscreen behind the interior Turn ring A to the first notch
screen wipers operate automatically mirror. for intermittent wiping.
and adapt their speed to the inten- When using an automatic car
sity of the rainfall. wash, switch off the ignition or
check that the wiper control is not
in the automatic position.
Operating check
In winter, it is advisable to wait for Rear windscreen wash
Activation the windscreen to completely
clear of ice before operating the
When the function is activated, the automatic wipe.
message "Automatic windscreen Turn ring A past the first
wiping active" appears on the multi- notch; the windscreen wash
function display. then the windscreen wiper
operate for a fixed period.
Deactivation
Deactivation of the function is
accompanied by a bleep.
In the event of malfunction, the
driver is informed by an audible
signal and the message "Auto
windscreen wiper faulty" on the
multi-function display.
In the AUTO position, the wind-
screen wiper will operate in intermit-
tent mode.
Contact a PEUGEOT dealer to have
the system checked.
29-09-2003
114
YOUR 307 IN DETAIL
TRIP COMPUTER Colour screen DT
Each time the button on the end of the

wiper stalk is pressed, the following
sequence of data is displayed:
Monochrome screen B Monochrome screen CT

the "Current information" with:
the range,
the current consumption,
the distance still to be driven.
'Route 1' with:
the remaining range the 'vehicle' tab with:
the distance travelled,
the distance travelled range, current consumption and
the distance still to be driven, the average consumption,
the average consumption
the average speed,
the current consumption tab '1' (route '1') with:
the average speed the distance driven, the average 'Route 2' with the same features.
consumption and the average It also permits access to the warning
In addition, it allows access to the speed calculated over route "1" log information.
warning log information. tab '2' (route '2') with the same
features. Zero re-set
It also permits access to the warning When the required route is displayed,
Zero reset log information. press the button for more than two
Press the stalk for more than two seconds.
seconds. Zero re-set
When the required route is dis-
played, press the button for more
than two seconds.
29-09-2003
115
YOUR 307 IN DETAIL
Range Distance travelled

This shows the distance that can still This indicates the distance travelled
be covered with the fuel remaining in since the computer was last set to
the tank. zero.
Note: this figure may increase if
there is a change in the style of Distance remaining to be
driving or the road surface, producing
a significant drop in current travelled
consumption. This is the distance remaining to
When the range is less than 20 miles the destination. It can either be cal-
(30 km), three segments are dis- culated by the navigation if guidance
played. After filling with fuel, the is activated, or entered by the user,
range is displayed when it exceeds minus the distance covered since the
62 miles (100 km). distance was entered.
If horizontal segments are displayed Note: if digits are missing, dashes
for long periods instead of digits, are displayed in their place.
contact a PEUGEOT dealer. The routes
Average speed The routes "1" and ''2'' are inde-
Current consumption This is the average speed calculated pendent but have identical application.
This is the average quantity of since the computer was last set to
zero (with the ignition on). Route "1" for example allows you to
fuel consumed during the last few make daily calculations and route
seconds. "2" monthly calculations.
This function is displayed only when The warning log
the vehicle is travelling at a speed This summarises the active warning
greater than 20 mph (30 km/h). messages by displaying them on the
multi-function display.
Average consumption
This is the average fuel consumption
since the computer was last set to
zero.
29-09-2003
116
YOUR 307 IN DETAIL
Specific features Trip computer configuration

of the monochrome screen This function allows the distance to
CT and the colour screen DT the destination to be input (when
guidance is not activated; otherwise
General menu this information is given by the navi-
gation system) and also changing of
Press the "MENU" button to access the units of measurement (C or F,
the general menu. km and litres or miles and gallons).
Select the icon ''Trip computer''
using the dial, then validate to Distance to destination
access the ''Trip computer'' menu.
When guidance is not activated, this
The ''trip computer'' menu offers enables an approximate value to be
various choices: entered to make all the trip computer
Trip computer configuration, calculations possible.
Warning log.
'Trip computer' context menu

The context menu associated with
the "Trip Computer" application
appears as a superimposed display
when the Trip Computer is the appli-
cation currently being used in the
main screen window.
Briefly press the continuous applica-
tion 'Trip computer' button to select
one of the following functions:
Warning log,
Distance to destination.
29-09-2003
117
YOUR 307 IN DETAIL
Automatic operation: REINITIALISATION OF THE

Press or pull switch fully: the window WINDOWS
opens or closes completely when the Following reconnection of the battery or
switch is released. Pressing the switch in the event of a malfunction, release
again stops the movement of the the switch and pull it again until it closes
window. completely. Hold the switch for approxi-
mately one second after closing.
Note: when one of the doors is
opened or approximately 45 seconds The safety auto-reverse function is
following removal of the ignition key, not active during these operations.
none of the windows can be opened
or closed. The ignition must be
switched on again to open or close
the windows.
Safety auto-reverse
ELECTRIC WINDOWS When the window rises and meets
an obstacle, it stops and partially
1 - Driver's electric window lowers again.
switch. Note:
2 - Passenger's electric window In the event of unwanted opening of
switch. the window on closing (for example in Always remove the key
3 - Rear right electric window the presence of frost), press the from the ignition when
switch. switch until it opens completely, then leaving the vehicle, even
pull it immediately until it closes. for a short time.
4 - Rear left electric window Continue to hold the switch for approx- In the event of contact during
switch. imately one second after the window operation of the windows, you
5 - Disarming of the rear has closed. must reverse the movement of the
The safety auto-reverse function is window. To do this, press the
electric window switches switch concerned.
(child lock). not active during these operations.
When the driver operates the pas-
You have two options: Disarming the rear window senger electric window switches,
controls he must ensure that no one is
Manual operation: preventing correct closing of the
For the safety of your children, press windows.
Press or pull switch gently. The switch 5 to prevent operation of the
window stops as soon as the switch The driver must ensure that the
rear windows irrespective of their passengers use the electric
is released. position. windows correctly.
When the button is raised, disarming Be aware of children when operating
is active. When the button is low- the windows.
ered, disarming is deactivated.
29-09-2003
118
YOUR 307 IN DETAIL
PARTIALLY OPENING EXTERIOR MIRRORS Manual exterior mirrors

REAR WINDOWS
Electric rear view mirrors Move the lever in all four directions
To partially open the rear windows, Slide switch A to the right or to adjust.
tilt the lever and push it fully to lock to the left to select the corre- When the vehicle is parked, the
the windows in the open position. sponding mirror. exterior mirrors can be folded back
Move knob B in all four directions manually.
to adjust.
Return switch A to the centre
position.
The exterior mirror on the
When parked, the mirrors can be driver's side is convex
folded back electrically by pulling (outer edge defined by a
knob A rearwards or automatically dotted line) in order to
when locking the vehicle. eliminate the 'blind spot'.
The exterior mirrors are unfolded by As a result, objects observed in
switching on the ignition to the the driver's and passenger's
second notch or to the ON position. mirrors are in reality closer than
Note: the function that controls they appear.
folding of the mirrors when locking This must be taken into account to
the vehicle can be disarmed. Contact correctly judge the distance of
a PEUGEOT dealer. vehicles approaching from behind.
29-09-2003
119
YOUR 307 IN DETAIL
Manual interior mirror

The interior mirror has two positions:
day (normal),
night (anti-dazzle).
To change from one to the other,
push or pull the lever on the lower
edge of the mirror.
Automatic day/night interior mirror

This automatically and gradually changes between the day and night positions.
To prevent dazzling, the glass of the mirror darkens automatically depending on
the intensity of the light from behind. It clears as the light (headlamps of following
vehicles, sunlight) decreases, ensuring maximum visibility.
Operation
Switch on the ignition and press switch 1:
Indicator light 2 lit (switch pressed): automatic operation.
Indicator light 2 off: automatic system off. The mirror remains at its most clear. AREAS FOR TOLL CARDS/
CAR PARK TICKETS
Special feature
The athermic windscreen has two
To ensure maximum visibility during manoeuvres, the mirror clears automatically non-reflective zones located either
when reverse gear is engaged. side of the base of the interior mirror.
They are intended for affixing toll
cards and/or car park tickets.
29-09-2003
120
YOUR 307 IN DETAIL
HEADLAMP ADJUSTMENT HAZARD WARNING LIGHTS STEERING WHEEL HEIGHT

Press the button, the direction AND DEPTH ADJUSTMENT
Depending on the load in your vehicle,
it is recommended that the headlamp indicators flash.
When the vehicle is stationary,
beam is adjusted. They can operate with the ignition off. unlock the steering wheel by pulling
0 - 1 or 2 people in the front seats. handle A.
- 3 people. Automatic lighting of hazard Adjust the height and depth of the
steering wheel, then lock it by
1 - 5 people. warning lights* pushing handle A down fully.
2 - 5 people + maximum authorised When braking in an emergency,
load. depending on the force of decelera-
3 - Driver + maximum authorised tion, the hazard warning lights come
load. on automatically. They switch off auto- HORN
matically the first time you accelerate.
It is also possible to switch them off Press one of the spokes or the centre
Initial setting is position 0. by pressing the button. of the steering wheel.
29-09-2003
121
YOUR 307 IN DETAIL
COURTESY LIGHTS
1 - Front courtesy light
2 - Map reading lights
3 - Rear courtesy light
4 - Rear reading lights (estate)
With the key in the accessories position (1st notch) or with the ignition on, operate the relevant switch.
The front and rear courtesy lights come on when the ignition key is removed, on unlocking the vehicle or on opening one of
the doors.
They gradually go off after the ignition has been switched on or the vehicle is locked.
In addition, when the vehicle is moving, the front and rear courtesy lights flash if a door or the tailgate is not closed properly.
Pressing switch 1 switches on the front and rear courtesy lights for a duration of ten minutes.
Pressing switch 3 or 4 switches on the rear courtesy light or the reading light concerned for a duration of ten minutes.
Note: The courtesy lights can be deactivated by pressing switch 1 for more than three seconds. A short press on switch 1
switches the front courtesy light on and off. The map reading lights are not affected by this and may be switched on.
To re-activate the lights, press the switch 1 for more than three seconds.
29-09-2003
122
YOUR 307 IN DETAIL
SUN VISOR WITH

ILLUMINATED COURTESY
MIRROR
ROOF CONSOLE
With the ignition on, the mirror is
automatically lit up when the flap is The front courtesy light and a
opened. spectacles holder are fitted in the
roof console.
To open or close the spectacles
holder, press the recess in the cover.
29-09-2003
124
YOUR 307 IN DETAIL
29-09-2003
125
YOUR 307 IN DETAIL
INTERIOR LAYOUT
1 - Glove box
This is fitted with a lock.
To open the glove box, lift the handle.
The glove box lights when the lid is opened.
It contains a ventilation nozzle that can be closed, distributing the same conditioned air as the vents of the passenger
compartment, and three sockets for connecting video equipment.
The layout allows storage of a water bottle, a pen, the vehicle handbook, a pair of spectacles, tokens etc.
2 - Front ashtray
Pull the lid to open the ashtray.
To empty it after opening, press the tab and extract the ashtray.
3 - Storage
4 - 12 volt accesories socket
This is a lighter type socket, fitted with a cap. It is supplied with current from the accessories position (1st notch).
5 - Door tray
6 - Storage/Cup/can holder
7 - Coin storage
8 - Waste container
To empty this, open it fully (past the point of resistance) then pull on the receptacle to remove it.
To refit, lock it in place on the cover.
29-09-2003
126
YOUR 307 IN DETAIL
29-09-2003
127
YOUR 307 IN DETAIL
BOOT LAYOUT (SALOON)
1 - Rear parcel shelf

To remove the shelf:
unhook the two strings,
slightly raise the shelf, then remove it.
There are several options for storing the shelf:
either behind the front seats,
or behind the rear seat.
2 - Hooks
3 - Stowing rings
4 - Luggage retaining net

Hooked onto the stowing rings, this enables your luggage to be secured.
5 - Open storage trays
6 - Socket for accessories

This is a 12 volt socket (lighter type), installed on the left-hand side of the parcel shelf.
It is supplied with the ignition off.
29-09-2003
128
YOUR 307 IN DETAIL
29-09-2003
129
YOUR 307 IN DETAIL
BOOT LAYOUT (ESTATE)
1. Load space cover
To install it:
position the front ends of the cover on its support and press gently to put it in place,
unfold the cover fully,
position the rear ends of the cover on its support and press gently to put it in place.
To remove it:
unclip the rear ends,
fold the cover fully,
unclip the front ends and remove the cover.
To store it, slide it under the rear seats (location A).
2. Boot floor and pillar stowing rings
3. Rear seat stowing rings
4. Luggage retaining net
Secure the net hooks in the stowing rings on the floor or on the folded rear seat (two horizontal positions) or secure the
net hooks in the stowing rings on the boot pillars and in the floor rings at the rear of the boot (one vertical position).
5. Floor storage compartments (2/3 - 1/3)
6. Side storage compartments with boot light
7. Storage nets
One of them contains the luggage retaining net.
8. 12 V socket for accessories
This is a 12 V socket (lighter type), installed on the load space cover left support.
It is supplied with the ignition off.
9. High load retaining net fixings
The high load retaining net can be installed behind the front or rear seats.
Open the covers of the corresponding upper fixings.
Fit the ends of the metal bar in these fixings.
To install the high load retaining net:
behind the front seats, lift the rear seat cushion, hook the net straps on the fixings then fold the rear seat;
behind the rear seat, hook the net straps in the stowing rings on the floor.
The rings are located directly below the corresponding upper fixings.
Pull the two straps taut.
10. Grab handles and coat hooks
29-09-2003
130
YOUR 307 IN DETAIL
"PORSCHE TIPTRONIC SYSTEM" AUTOMATIC GEARBOX Moving off

The four speed automatic gearbox offers a choice between the comfort of With the engine running, to move off
integral automatic operation, enhanced by a sport and a snow programme, from position P:
or the pleasure of manual gear changing. it is essential to press the
brake pedal to exit position P,
select function R, D or M, then
gradually release the pressure
Gear selection gate on the brake pedal; the vehicle
Move the lever in the gate to select a function. moves off immediately.
Once the function is selected, the corresponding indicator light appears on You can also move off from position N:
the instrument panel display. release the handbrake, with your
foot on the brake,
select function R, D or M, then
S: sport programme gradually release the pressure
on the brake pedal; the vehicle
moves off immediately.
: snow programme
WARNING
Park: to immobilise the vehicle or start the engine,
with the handbrake on or off. When the engine is at idle, brakes not
applied, if function R, D or M is select-
ed the vehicle moves even without
Reverse: to reverse (select this function with the vehicle the accelerator being pressed.
stationary, engine at idle).
For this reason, do not leave chil-
dren unsupervised inside the
Neutral: to start the engine and to park, with the vehicle, with the engine running.
handbrake on. When maintenance operations need
Note: if function N is engaged inadvertently while to be carried out with the engine run-
driving, allow the engine to return to idle before ning, apply the handbrake and select
engaging function D to accelerate. position P.
Drive: for driving in automatic mode.
Manual: for driving in manual mode.
29-09-2003
131
YOUR 307 IN DETAIL
Automatic operation If you take your foot off the accelera- Manual operation
tor suddenly, the gearbox will not
Automatic changing of the four change to a higher gear for reasons Manual changing of the four gears:
gears: of safety. select function M in the gate,
select function D in the gate. push the lever to the + sign to
The gearbox always selects the most change to a higher gear,
suitable gear according to the follow- Sport and snow programme
pull the lever to the sign to
ing parameters: In addition to the auto-adaptive pro- change to a lower gear.
the style of driving, gramme, there are two special pro-
grammes. You can change from position D
the road profile, (driving in automatic mode) to posi-
The programme is displayed on the tion M (driving in manual mode) at
the vehicle load. instrument panel screen. any time.
The gearbox is then operating in
auto-adaptive mode, without any Sport programme
action on your part. Note
Press button S once the vehicle
WARNING has been started and function D It is only possible to change from one
selected. gear to another if the vehicle speed
Never select function N when the The gearbox automatically favours and engine speed permit. If they do
vehicle is moving. sporty driving and more dynamic not, the vehicle will operate tem-
Never select functions P or R unless acceleration. porarily in automatic mode.
the vehicle is stationary. When the vehicle is stationary or
Never change between functions to Snow programme moving very slowly, the gearbox
optimise braking on a slippery surface. automatically selects gear M1.
This programme improves starting
Notes and drive when traction is poor. Programme S (sport) and (snow)
do not operate in manual mode.
For immediate maximum accelera- Press button once the vehicle
tion without touching the gear lever, has been started and function D
press the accelerator pedal down as selected.
far as it will go (kickdown). The gear- The gearbox adapts to driving on
box will automatically change down slippery roads.
or maintain the gear selected until Note: you can return to the auto-
maximum engine speed is reached. adaptive programme at any time.
When braking, the gearbox will auto- Press button S or again to
matically change down in order to switch off the programme you are in.
provide efficient engine braking.
29-09-2003
132
YOUR 307 IN DETAIL
Operating abnormality HANDBRAKE

Any operating abnormality is indicat- Applying
ed by an audible signal, accompa-
nied by the message "Automatic Pull the handbrake to immobilise
gear fault" on the multi-function dis- your vehicle.
play, "" and flashing of the Sport
and Snow warning lights on the Warning: when parking on a slope,
instrument panel. direct your wheels towards the pave-
In this situation the gearbox operates ment and pull the handbrake.
in downgrade mode (locked in 3rd
gear). You may feel a substantial
knock when changing from P to R
and from N to R (this will not cause
any damage to the gearbox). Releasing
Do not exceed 60 mph (100 km/h), Pull on the handle and press the
keeping within the limit of local button to release the handbrake.
speed restrictions.
Contact a PEUGEOT dealer as soon
as possible. Illumination of this warning
light and of the STOP warning
light, accompanied by an
audible signal (while the
vehicle is being driven) and
the message "handbrake on" on
the multi-function display, indicates
that the handbrake is still on or has
not been properly released.
If the battery is flat and the

lever is in position P, it will
be impossible to change to
another position.
29-09-2003
133
YOUR 307 IN DETAIL
ANTI-LOCK BRAKING SYSTEM Stop immediately. EMERGENCY BRAKING

(ABS) AND THE ELECTRONIC In both cases, consult a PEUGEOT ASSISTANCE SYSTEM
BRAKE FORCE DISTRIBUTION dealer.
(EBFD) In an emergency, this system
enables the optimum braking pres-
The ABS, in conjunction with the sure to be reached more quickly,
electronic brake force distribution, thus reducing the stopping distance.
Normal operation of the ABS may It is triggered by the speed at which
increases the stability and make itself felt by slight vibrations
manoevrability of your vehicle on the brake pedal is activated. The
of the brake pedal. effect of this is a reduction in the
braking, in particular on poor or slip-
pery road surfaces. In emergency braking, press resistance of the pedal and an
very firmly without releasing increase in braking efficiency.
Note: when changing wheels (tyres the pressure.
and rims), make sure that these are
approved.
The anti-lock braking system comes

into operation automatically when
there is a risk of wheel lock.
When this warning light
comes on, accompanied by
a buzzer and the message
"ABS fault", it indicates
that there is a malfunction of
the ABS, which can cause a loss of
control of the vehicle when braking.
When this warning light

comes on, connected to the
STOP and ABS warning
lights, accompanied by a
buzzer and the message
'Braking fault', it indicates that there
is a malfunction of the electronic
brake force distribution, which can
cause a loss of control of the vehicle
when braking.
29-09-2003
134
YOUR 307 IN DETAIL
TRACTION CONTROL (ASR) Disarming the ASR/ESP systems Operating check

AND DYNAMIC STABILITY In exceptional conditions (starting a
CONTROL (ESP) When a malfunction of the
vehicle which is bogged down, stuck systems occurs, the switch
in snow, on soft ground, ...), it may light flashes and the warning
These systems are linked and com- be advisable to disarm the ASR and
plement the ABS. light comes on, accompa-
ESP systems, so that the wheels can nied by an audible signal
The ASR system optimises drive to move freely and regain grip. and the message "ESP/ASR not
prevent the wheels skidding, by act- functioning" on the multifunction
ing on the brakes of the drive wheels display.
and on the engine. It also allows the
directional stability of the vehicle to Contact a PEUGEOT dealer to have
be improved on acceleration. Press the "ESP OFF" switch, the system checked.
located on the central section of
If there is a variation between the tra- the fascia.
jectory followed by the vehicle and
that required by the driver, the ESP
system automatically acts on the The switch lights up and the
engine and the brake of one or more warning light comes on: the The ESP/ASR systems
wheels, in order to put the vehicle ASR and ESP systems are offer exceptional safety in
back on course. disarmed. normal driving, but this
should not encourage the
driver to take extra risks
or drive at high speed.
These are triggered again: The correct functioning of these
automatically if the ignition is systems depends on observation
switched off, of the manufacturer's recommen-
dations regarding the wheels (tyres
automatically above 30 mph and rims), the braking components,
(50 km/h), the electronic components, and the
Operation of the ASR and ESP manually by pressing the switch PEUGEOT assembly and opera-
systems again. tion procedures.
The warning light flashes if After an impact, have the system
the ASR or ESP is activated. checked by a PEUGEOT dealer.
29-09-2003
135
YOUR 307 IN DETAIL
Operation Recalling the memorised

Place switch 1 in the ON position.
speed
A speed can be memorised. After cancellation, press button 4.
Your vehicle will return to the last
memorised speed.
Place switch 1 in the OFF posi-
tion to cancel.
Changing a memorised speed
Memorising a speed To memorise a speed higher than
the previous one:
As soon as you reach the chosen press button 3;
speed, press button 2 or 3. This
memorises the speed, which will be release it when you have
maintained automatically. reached the required speed.
CRUISE CONTROL Note: It is possible to accelerate and To memorise a speed lower than the
drive momentarily at a speed greater previous one:
Cruise control enables the vehicle to than the memorised speed. When appuyez sur la touche 2;
maintain a steady speed pro- the accelerator pedal is released, the
grammed by the driver, regardless of release it when you have
vehicle will return to the memorised reached the required speed.
the road characteristics and without speed.
the driver having to touch the accelera-
tor or brake pedals. Cancelling the cruise control
In order for it to be memorised, the Cancelling the memorised
vehicle speed must be greater than speed Place switch 1 in the OFF posi-
25 mph (40 km/h) (manual gearbox) tion or switch off the ignition.
or 40 mph (60 km/h) (automatic If you wish to cancel the memorised
gearbox) and fourth gear at least speed:
must be engaged (second gear for press button 4 or the brake or
the automatic gearbox). clutch pedal.
Do not use cruise control

on slippery roads or in
heavy traffic.
29-09-2003
136
YOUR 307 IN DETAIL
Selecting the function Cancelling the memorised speed

Place switch 1 in the CRUISE posi- If you wish to cancel the memorised
tion. The cruise control is not yet speed:
active and no speed has been Press button 4 or the brake or clutch
memorised. The display indicates: pedal. The display indicates (e.g. at
80 mph (130 kmh)):
Switching the function off

Place switch 1 in position 0 or
CRUISE CONTROL/SPEED LIMIT to switch the system off. Note: the speed memorised is can-
LIMITER* celled automatically if the vehicle
speed is less than 25 mph (40 kmh),
Cruise control function: this enables Activation/memorising a speed or if the manual gearbox is in a gear
the vehicle to maintain a steady speed As soon as you reach the chosen lower than fourth (second gear for
programmed by the driver, regardless speed, press button 2 or 3. This the automatic gearbox) or if the ESP
of the road characteristics and without memorises the speed, which will is activated.
the driver having to touch the accelera- be maintained automatically. The
tor or brake pedals. display indicates (e.g. at 80 mph
In order for it to be memorised, the (130 km/h)):
vehicle speed must be greater than
25 mph (40 km/h) with at least fourth
gear engaged (second gear for the
automatic gearbox), with the engine Recalling the memorised speed
running. After cancellation, press button 4.
Your vehicle will return to the last
memorised speed. The display indi-
cates (e.g. at 80 mph (130 km/h)):
Note: It is possible to accelerate and
drive momentarily at a speed greater
than the memorised speed. The
value memorised flashes. When the
accelerator pedal is released, the
* During the year, according to engine. vehicle will return to the memorised
speed.
29-09-2003
137
YOUR 307 IN DETAIL
Changing a memorised speed Operating check

To memorise a speed higher than In the event of a cruise control mal-
the previous one, there are two function, the memorised speed is
options: erased, the dashes flash for a few
seconds:
Without using the accelerator:
press button 3;
A brief press increases by 1 mph
(1 km/h).
An extended press increases the
memorised speed progressively.
Using the accelerator: Contact a PEUGEOT dealer to have

exceed the memorised speed the system checked.
until the required speed is
reached,
Note: the appearance of this display is
press button 2 or 3. normal if the memorising conditions
are not met.
To memorise a speed lower than the
previous one:
press button 2
A brief press decreases by 1 mph
(1 km/h). An extended press decreases
the memorised speed progressively.
Cancelling the memorised speed

LIMITor switch off the ignition.
Do not use cruise control

on slippery roads or in
heavy traffic.
29-09-2003
138
YOUR 307 IN DETAIL
Selecting the function Exceeding the programmed

Place switch 1 in the LIMIT posi- speed
tion. The limiter is not yet active. By Pressing the accelerator to exceed
default the display indicates: the programmed speed will have no
effect unless the pedal is pressed
firmly (passing the point of resis-
tance).
The limiter is deactivated temporarily and
displays (e.g. at 80 mph (130 km/h)):
Switching the function off

CRUISE or switch off the ignition to
switch the system off. The last
CRUISE CONTROL/SPEED speed programmed remains in the
LIMITER* memory. To re-activate the limiter, release the
Limiter function: this prevents the accelerator to slow down to a speed
Memorising a speed below the programmed speed.
vehicle speed exceeding the speed A speed can be memorised without
programmed by the driver (minimum activation of the limiter. Note: sometimes (on a steep
speed of 20 mph (30 km/h)). A brief press on buttons 2 and 3 descent), the limiter may not prevent
decreases or increases by 1 mph the vehicle from exceeding the pro-
(1 km/h). An extended press decreas- grammed speed, this speed flashes.
The operations must be carried
out with the engine running. es or increases the memorised speed
progressively.
Operating check
Activation/deactivation of the In the event of a limiter malfunction,
limiter the memorised speed is erased, the
Pressing button 4 activates the lim- dashes flash for a few seconds:
iter, pressing this button again deac-
tivates it.
When the limiter is active, the display
indicates (e.g. at 80 mph (130 km/h)):
* During the year, according to engine. Contact a PEUGEOT dealer to have

the system checked.
29-09-2003
139
YOUR 307 IN DETAIL
REAR PARKING ASSISTANCE

This system consists of four proximity
sensors, located in the rear bumper,
and a special speaker.
This detects any obstacle (person,
vehicle, tree, gate, etc.) behind the
vehicle. Nevertheless, it cannot
detect obstacles located just below
the bumper.
An object, such as a stake, a road-
works cone or any other similar
object may be detected at the begin-
ning of the manoeuvre, but may no
longer be detected when the vehicle
comes close to it.
Note: this function will be disarmed Detection zone

automatically when the vehicle is
towing a trailer or when a bicycle car-
rier is fitted (vehicle fitted with towing
attachment or bicycle carrier recom- Activation Deactivation
mended by PEUGEOT).
The system is activated as soon as In neutral, the system is again inactive.
In bad or wintry weather, ensure that reverse gear is engaged; an audible
the sensors are not covered with bleep shows that it is active.
mud, frost or snow.
The proximity information is given by
an audible signal, which becomes
more rapid as the vehicle approaches
the obstacle.
When the distance between the rear
of the vehicle and the obstacle is
less than thirty centimetres, the audi- If there is an operating
ble signal becomes continuous. fault, the audible signal will
be a short bleep followed
by a long bleep when
changing to reverse gear.
29-09-2003
140
YOUR 307 IN DETAIL
AIR BAGS
The air bags have been designed to
maximise the safety of the occupants
in the event of serious collisions.
They work in conjunction with the
force-limiting seat belts. The elec-
tronic detectors register and analyse
any abrupt deceleration of the vehicle:
if the triggering threshold is reached,
the air bags inflate instantly and pro-
tect the occupants of the vehicle.
Immediately after the impact, the air
bags deflate rapidly so that they do Disarming the passenger air
not hinder the visibility of the occu- bag*
pants nor their exit if necessary from
the vehicle. To ensure the safety of your child,
it is essential to disarm the pas-
The air bags are not deployed in the FRONT AIR BAGS senger air bag when you install a
case of collisions which are not rear-facing child seat on the front
serious, for which the seat belt is suf- These are folded in the centre of the passenger seat. Otherwise, the
ficient to ensure maximum protec- steering wheel for the driver and in child would risk being killed or
tion. The seriousness of a collision the fascia for the front passenger. seriously injured if the air bag
depends on the nature of the obstacle They are deployed simultaneously, were to inflate.
and the speed of the vehicle at the except in cases where the passenger
moment of the collision. air bag is disarmed.
Air bags only operate when the With the ignition switched off,
ignition is switched on. insert the key into the passenger
Front air bag fault air bag disarming switch 1, turn it
Note: the gas escaping from the air to the "OFF" position, then
bags can be a minor irritant. If this warning light comes remove the key keeping the slot
on, accompanied by an in this position.
audible signal and the mes-
sage "Air bag fault" on the The air bag warning light on the
multifunction display, con- instrument panel is lit throughout the
tact a PEUGEOT dealer to have the disarming process.
system checked.
29-09-2003
141
YOUR 307 IN DETAIL
In the "OFF" position, the passenger SIDE AIR BAGS* AND CURTAIN
air bag will not be triggered in the AIR BAGS* If the two "Air bag fault" and
event of an impact. "Passenger air bag dis-
The side air bags are incorporated armed" warning lights come
As soon as the child seat is on permanently, do not
removed, turn the air bag slot to the into the front seat backs on the door
side. install a rearward facing child seat
"ON" position to re-activate the air and consult a PEUGEOT dealer.
bag and thus ensure the safety of The curtain air bags are incorporated
your passenger in the event of an into the door pillars and the upper part
impact. of the passenger compartment.
They are deployed independently of
each other, on whichever side the col-
lision occurs.
Disarming check
This is confirmed by an indicator
light, accompanied by an audible sig- Operating check
nal and a message on the multifunc- This is confirmed by an indicator light,
tion display. accompanied by an audible signal and
a message on the multifunction dis-
play.
With the ignition on (2nd If this indicator light comes
notch), illumination of this on, accompanied by an audi-
warning light accompanied ble signal and the message
by an audible signal and the "Air bag fault" on the multi-
message "Passenger air bag deacti- function display, contact a
vated" on the multi-function display, PEUGEOT dealer to have the system
indicates that the passenger air bag is checked.
disarmed (switch in the "OFF" posi-
tion).
29-09-2003
142
YOUR 307 IN DETAIL
For the front, side* and curtain* air bags to be fully effective, observe the following safety rules:
Wear a correctly adjusted seat belt.

Sit in a normal upright position.
Do not leave anything between the occupants of the front seats and the air bags (a child, pet, object).
This could hamper the operation of the air bags or injure the occupants.
All work on the air bag system is strictly forbidden unless it is carried out by qualified personnel of the PEUGEOT
network.
After an accident or if the vehicle has been stolen or broken into, have the air bag systems checked.
Front air bags
Do not drive holding the steering wheel by its spokes or resting your hands on the centre part of the wheel.
Passengers must not place their feet on the fascia.
Smoke as little as possible; deployment of the air bags can cause burns or the risk of injury from a cigarette or pipe.
Never remove or pierce the steering wheel or hit it violently.
Side air bags*
Only put approved covers on the front seats. Contact your PEUGEOT dealer.
Do not fix or glue anything to the front seat backs. This could cause injury to the chest or arms when the side air bag
inflates.
Do not sit with the upper part of the body any nearer to the door than necessary.
Curtain air bags*
Do not fix or glue anything to the pillars or the roof. This could cause injury to the head when the curtain air bag
inflates.
Do not remove the bolts from the grab handles installed on the roof, they play a part in securing the curtain air bags.
29-09-2003
143
PRACTICAL INFORMATION
1.4 LITRE PETROL ENGINE

1 - Power steering reservoir. 4 - Brake fluid reservoir. 7 - Air filter.
2 - Windscreen/headlamp* wash 8 - Dipstick.

5 - Battery.
reservoir. 9 - Engine oil reservoir.
3 - Coolant reservoir. 6 - Fuse box. * According to destination.

29-09-2003
144
1.4 LITRE 16V PETROL ENGINE

2 - Windscreen and headlamp* 8 - Dipstick.

5 - Battery.
wash reservoir. 9 - Engine oil reservoir.

29-09-2003
145
1.6 LITRE 16V PETROL ENGINE


5 - Battery.

29-09-2003
146
2 LITRE 16V PETROL ENGINE


5 - Battery.

29-09-2003
147
1.4 LITRE TURBO DIESEL HDI ENGINE

1 - Power steering reservoir. 4 - Brake fluid reservoir. 8 - Dipstick.
2 - Windscreen/headlamp* wash 5 - Battery. 9 - Engine oil reservoir.
reservoir. 6 - Fuse box. 10 - Priming pump.
3 - Coolant reservoir. 7 - Air filter. * According to destination.

29-09-2003
148
2 LITRE TURBO DIESEL HDI ENGINE (90 bhp/110 bhp)

2 - Windscreen/headlamp* wash 5 - Battery. 9 - Engine oil reservoir.
reservoir. 6 - Fuse box. 10 - Priming pump.

29-09-2003
149
2 LITRE 16V TURBO DIESEL HDI ENGINE

9 - Engine oil reservoir.
2 - Windscreen/headlamp* wash 5 - Battery.
10 - Priming pump.
reservoir. 6 - Fuse box.
11 - Degas screw.
29-09-2003
150
CHECKING THE LEVELS Viscosity selection Slacken the cap to the first notch to
release the pressure to prevent any
In all cases, the oil selected must risk of scalding. When the pressure
Oil level meet the manufacturer's require- has dropped, remove the cap and
Check the level regularly and top ments. top up the level.
up between changes. The maxi- Note: the coolant does not need to be
mum consumption is 0.5 l per Brake fluid level:
changed.
600 miles (1 000 km). The level must always be between
Check the level with the vehicle level, the DANGER and MAXIMUM Used oil
engine cold, using the oil level gauge marks in the reservoir. Do not dispose of used oil, brake
on the instrument panel or the dipstick. If the level drops substantially, con- fluid or coolant into drains or into the
tact a PEUGEOT dealer immedi- ground.
ately.
Fluid change: Power steering reservoir
Dipstick
must be carried out according to Open the reservoir, with the
the manufacturer's servicing engine at ambient temperature.
There are two marks on schedule.
the dipstick: The level should always be
use fluids recommended by the above the MIN. mark and close
A = maximum manufacturer, which fulfil DOT4 to the MAX. mark.
Never fill past this mark. standards.
B = minimum Note: brake fluid is harmful to health
To maintain the reliability and very corrosive. Avoid all contact Windscreen and headlamp*
of engines and emission with the skin. wash level
control systems, the use
of additives in engine oil Cooling system For best quality cleaning and for your
is prohibited. safety, we would advise that you use
Use the fluid recommended by the products recommended by PEUGEOT.
manufacturer.
When the engine is warm, the tem-
perature of the coolant is controlled
Oil change by the engine fan. As this fan can
operate with the ignition key
According to the information given in removed and because the cooling
"PEUGEOT SERVICING". system is pressurised, wait for at
least one hour after the engine has
Note: avoid used oil coming into pro- stopped before carrying out any
longed contact with the skin. work.
29-09-2003
151
CHECKS Oil filter RUNNING OUT OF FUEL

Change the filter regularly, in accor- (DIESEL)
Battery dance with the servicing schedule.
If you should run out of fuel, it is nec-
At the start of winter, have your bat- essary to re-prime the circuit.
tery checked by a PEUGEOT dealer.
The repriming pump, the degas
screw and the transparent pipe are
Air filter and passenger located under the bonnet (see corre-
compartment filter sponding drawing):
Have the filter elements replaced 1.4 litre HDI engine
regularly. If you drive in dusty con- fill the fuel tank with at least five
ditions, change them twice as litres of diesel,
often.
operate the manual re-priming
pump until fuel appears in the
Brake pads transparent pipe,
operate the starter until the engine
Brake pad wear depends on the starts.
style of driving, in particular for vehi-
cles which are used in town, over 2 litre HDI engine
short distances. fill the fuel tank with at least five
It may be necessary to check the litres of diesel,
thickness of the pads, even between operate the manual re-priming
services. pump until you feel resistance dur-
ing the manoeuvre,
Handbrake starts.
Where the handbrake travel is too 2 litre HDI 16V
great or there is a reduction in the Only use products recom-
performance of the system, the mended by PEUGEOT. fill the fuel tank with at least five
handbrake should be adjusted, even To ensure best perform- litres of diesel,
between services. ance from components unscrew the degas screw,
Have the system checked by a as important as the operate the manual repriming
PEUGEOT dealer. power steering and the braking pump until diesel is seen escaping
system, PEUGEOT selects and via the degas screw,
offers quite specific products. retighten the degas screw,
starts.
29-09-2003
152
CHANGING A WHEEL Tools Removing the wheel

(SALOON) The following tools are located in a Place the holder and the chock
polystyrene holder in the centre of 3 (or chock 3 on its own if neces-
Parking the vehicle the spare wheel: sary) under the wheel diagonally
Park the vehicle on level, stable opposite to the one to be
and non-slippery ground. 1 - Wheelbrace. changed.
Apply the handbrake, switch off Remove the trim, using the
2 - Centralising tool. wheelbrace 1, pulling at the valve
the ignition and engage first or
reverse gear (position P for the 3 - Removable chock. passage hole.
automatic gearbox). 4 - Jack with handle. Loosen the wheel bolts (for vehi-
cles fitted with alloy wheels,
5 - Removable towing eye. remove the chrome trim first. See
Access to the spare wheel and the paragraph on 'Special features of
6 - Alloy wheel bolt trim remover. alloy wheels').
jack in the boot
Lift the floor using the handle and
secure it by hooking the cords to
the hooks of the parcel shelf.
29-09-2003
153
For your safety, always

change the wheel:
on level, stable, non-slippery

ground,
with the handbrake on and the
ignition switched off,
with first or reverse gear
engaged (position P for the
automatic gearbox),
with the vehicle chocked.
Never go underneath a vehicle

Place the jack 4 in contact with one Fold the jack 4 and remove it. that is supported only by a jack
of the four locating points A on the (use a ramp)
Fully tighten the bolts using the
sub-frame, (the one which is clos- wheelbrace 1.
est to the wheel to be changed). After changing the wheel:
Replace the wheel trim, starting
Extend the jack 4 until its base is in by placing the wheel trim notch have the tightening of the bolts
contact with the ground. Ensure opposite the valve, and press it and the tyre pressure checked
that the centre line of the base of on using the palm of the hand. by a PEUGEOT dealer as soon
the jack is straight above the locat- as possible.
ing point A. Put the tools and the wheel back
in the boot. have the punctured tyre
Raise the vehicle. repaired and refit it to the vehi-
Note: a diagram on the holder indi- cle as soon as possible.
Unscrew the bolts and remove the cates the location of the tools.
wheel.
Tighten the spare wheel securing
strap to prevent noise and for your
Fitting a wheel safety in the event of impact.
Position the wheel using the cen-
tralising tool to assist you.
Tighten the bolts by hand and
remove the centralising tool.
Partly tighten the bolts using the
wheelbrace 1.
29-09-2003
154
CHANGING A WHEEL (ESTATE)

Tools Parking the vehicle Access to the spare wheel
The following tools are located: As far as possible, park the vehi- Open the boot.
cle on level, stable and non-slip- Open the flap using the lug to
in the right-hand trim of the boot, pery ground. release the winch and gain
1 - Wheelbrace. Apply the handbrake, switch off access to its control nut.
2 - Removable towing eye. the ignition and engage first or Unscrew the nut fully, using the
3 - Socket for anti-theft bolts. reverse gear (position P for the wheelbrace 1, to unroll the winch
automatic gearbox). cable.
in the holder in the centre of the
spare wheel,
4 - Jack with handle.
5 - Centralising tool.
6 - Bolt cover tool.
7 - Removable chock.
29-09-2003
155
Removing the wheel

Detach the wheel/holder assem- Slide the holder cover to gain Place the jack 4 in contact with
bly from the rear of the vehicle. access to the tools. one of the four locating points A
Take out the notched hook to on the sub-frame; the closest
Place the chock 7 under the possible to the wheel to be
release the wheel, as shown in wheel diagonally opposite to the
the illustration. changed.
one to be changed.
Extend the jack 4 until its base is
Remove the trim, using the in contact with the ground.
wheelbrace 1, pulling at the Ensure that the centre line of the
valve passage hole (for vehicles base of the jack is straight above
fitted with steel wheels). the locating point A.
Loosen the wheel bolts (see Raise the vehicle.
"Special features of alloy
wheels" for vehicles fitted with Remove one bolt and position
alloy wheels). the centralising tool 5 in its place.
Note: you can use the other end Unscrew the other bolts and
of the tool 6 to unscrew the remove the wheel.
wheel bolts.
29-09-2003
156
Fitting a wheel
For your safety, always
Position the wheel using the cen- Close the flap using the lug to change the wheel:
tralising tool 5 to assist you. lock the winch.
Tighten the bolts by hand and Store the rest of the tools in the
remove the centralising tool 5. right-hand trim of the boot. on level, stable, non-slippery
ground,
Partly tighten the bolts using the with the handbrake on and the
wheelbrace 1. ignition switched off,
Fold the jack 4 and remove it. with first or reverse gear
engaged (position P for the
Fully tighten the bolts using the automatic gearbox),
wheelbrace 1. with the vehicle chocked.
Replace the wheel trim, starting
by placing the wheel trim notch Never go underneath a vehicle
opposite the valve, and press it that is supported only by a jack
on using the palm of the hand. (use a ramp).
Put the corresponding tools in
the holder and secure its cover. Never refit the holder under the
vehicle without the spare
Place the holder on the ground wheel.
and align the spare wheel on it.
Pass the notched hook into the After changing the wheel:
holder cover. have the correct positioning of
the punctured wheel, the tight-
Refit the wheel under the vehicle ening of the bolts and the tyre
tightening the winch control nut pressure checked by a
using the wheelbrace 1. PEUGEOT dealer as soon as
Fully tighten and check that the possible.
wheel is horizontally flush have the punctured tyre
against the rear floor. repaired and refit it to the vehi-
cle as soon as possible.
have the correct positioning of
the spare wheel checked by a
PEUGEOT dealer.
29-09-2003
157
Special features of alloy Anti-theft bolts

wheels If your wheels are fitted with an anti-
Bolt covers theft bolt (one per wheel), the
Fitting the spare wheel chrome trim and then the plastic
Alloy wheel bolts are covered by cover must be removed using tool 6,
chrome trims. If your vehicle is fitted with a steel before unscrewing the bolt using one
Use tool 6 to remove the trims before spare wheel, when fitting it, it is nor- of the two anti-theft sockets (which
slackening the bolts. mal when tightening the bolts to were given to you on delivery of your
notice that the washers do not come vehicle along with the duplicate keys
into contact with the rim. The spare and the confidential card) and the
wheel is secured by the cone shape wheel brace 1.
of each bolt.
Note: make a careful note of the code

Fitting snow tyres number engraved on the head of the
If you fit snow tyres mounted on steel anti-theft socket. This will enable you
wheels onto your vehicle, it is essen- to obtain duplicate anti-theft sockets
tial to use special bolts available from a PEUGEOT dealer.
from your PEUGEOT dealer.
29-09-2003
158
CHANGING A BULB The headlamps are fitted with polycarbonate glass with a
protective coating. Do not clean them with a dry or abra-
Front lights sive cloth, nor with a detergent or solvent product.
Use a sponge and soapy water.
Note: on the right-hand side, remove the style cover, fixed
with two plastic screws, to access the bulbs. Handle the 4 - Side lights (W 5 W).
bulbs with a dry cloth.
Pull the socket rearwards, remove the bulb and change it.
1 - Dipped beam headlamps (H7-55 W). 5 - Direction indicators (PY 21 W amber).
2 - Main beam headlamps (H1-55 W). Turn the bulb holder a quarter of a turn and remove it.
3 - Front fog lamps (H1-55 W). Change the bulb.
Turn the protective cover corresponding to the faulty Note: In certain climatic conditions (low temperature,
bulb a quarter of a turn and remove it. humidity), condensation inside the headlamp glass is
Disconnect the connector. normal; it disappears a few minutes after the lights are
switched on.
Press the end of the securing clip to free it. Change the
bulb.
When fitting the new bulb, ensure that the direction
notches are positioned correctly and the securing clip
is fixed properly.
Reconnect the connector.
Refit the protective cover, positioning it with the arrow
upwards, then turn it a quarter of a turn to the right.
29-09-2003
159
Press the tab and remove the

bulb holder,
Change the faulty bulb.
When refitting, take care to pass the
trim under the seal.
Direction indicator side Rear lights (saloon)

repeaters (WY 5 W amber).
Push the repeater forwards and 1 - Direction indicators (P 21 W).
release the assembly. 2 - Reversing lights (P 21 W),
Hold the connector and turn the right-hand side.
lens a quarter turn. Fog lamp (P 21 W), left-hand Third brake light (saloon)
Change the bulb. side. (4 W 5 W bulbs)
3 - Brake lights (P 21 W).
Using a 10 mm box spanner,
4 - Side lights (R 5 W). unscrew the 2 fixing nuts 1.
Release the lamp unit by pushing
These 5 bulbs are changed from it outwards.
Amber coloured bulbs inside the boot: Squeeze the two tabs 2 to release
(direction indicators and Raise and hook up the boot the bulb holder.
side repeaters), must be carpet, Change the faulty bulb.
replaced with bulbs of When refitting, ensure that the
identical specification Remove the boot sill trim, which
is fixed by two plastic clips, lamp unit seal has been put back
and colour. in place correctly.
Move aside the boot trim to
access the bulb holder,
29-09-2003
160
Rear lights (estate) Remove the bulb holder, Third brake light (estate)
pressing on the tabs A, 4 W 5 W bulbs
1 - Brake lights (P 21 W). Change the faulty bulb.
Remove the tailgate upper trim
2 - Side lights (R 5 W). Note: if necessary, use the wheel- carefully by unclipping it on either
brace to remove the nuts. side, perpendicular to its direc-
3 - Direction indicators (P 21 W). When refitting, take care to position tion of engagement.
4 - Reversing light (P 21 W), right- the bulb holder and the light correctly.
Insert a screwdriver into the two
hand side. outer holes B to press on the two
Fog lamp (P 21 W), left-hand tabs C.
side. Push the light unit outwards while
These 5 bulbs are changed by maintaining the pressure on the
removing the light: Number plate lights tabs.
Remove the corresponding boot (W 5 W) Pull the light unit outwards while
side trim to access the light, tilting it.
Insert a thin screwdriver into one
Remove the light fixing nut of the external holes of the lens. Change the faulty bulb.
inside the boot, When refitting, ensure that the
Push it outwards to unclip it.
Remove the light fixing nut out- light unit tabs are engaged cor-
side the boot, Remove the lens. rectly and that the tailgate upper
Change the faulty bulb. trim has been put back in place
Remove the light, correctly.
Unclip the harness,
29-09-2003
161
CHANGING A FUSE
The fuse boxes are located in the
lower part of the fascia (driver's side)
and in the engine compartment.
The spare fuses and special pliers A
are fixed to the inside of the lid of the
fascia panel fuse box.
Removing and changing a
fuse
Before changing a fuse, you must
establish the cause of the fault and
have it corrected. The fuse numbers Fascia panel fuses
are indicated on the fuse box. Unscrew the screw a quarter of a
Use the special pliers A. turn with a coin, then pull the
handle to open the cover and
Always change a faulty fuse for access the fuses.
one of the same rating.
Fuse no. Rating Functions
1 10 A Rear fog lamp.
2 15 A Rear screen wiper.
Correct Incorrect 4 15 A Front electric window - Sunroof.
5 15 A Left brake light including trailer.
7 30 A Rear courtesy light, front courtesy light, map reading

lights - 12 V front socket - Glove box lighting.
Pliers A
29-09-2003
162
Fuse no. Rating Functions
9 30 A Front electric windows - Front automatic windows - Sunroof.

10 15 A Diagnostic socket - 12 volt rear socket - Trailer.
11 20 A Audio equipment - Multifunction display - Steering wheel controls - Automatic gearbox.
12 10 A Front right and rear right side lights - Number plate and trailer lighting -
Central locking/alarm/hazard warning lights/ESP switch lighting -
Air conditioning/ashtray lighting -
Heated seats/Automatic gearbox switches lighting - Lighter.
14 30 A Door opening/closing controls - Deadlocking controls.
15 30 A Press-operation electric rear windows.
16 10 A Engine fuse box - Alarm - Particulate emission filter - Steering wheel controls - Air bags.
17 10 A Rear right brake light, 3rd brake light.
18 10 A Diagnostic socket - Steering wheel controls - Electrochromatic mirror -
Brake pedal (stop) and clutch switches - Coolant level switch - Second brake switch.
19 30 A PARC shunt.
22 10 A Front left and rear left side lights -
Number plate and trailer lighting.
23 15 A Alarm siren - Interior alarm control unit.
24 15 A Instrument panel - Audio equipment - Multifunction display - Air conditioning - Rear parking
assistance - Rain/brightness sensor.
26 30 A Heated rear screen.
29-09-2003
163
Engine compartment fuses

The electrical system of
Fuse box your vehicle is designed
to operate with standard
To access the fuse box in the engine or optional equipment.
compartment (next to the battery):
unclip the cover. Before installing other electrical
equipment or accessories on your
Carefully close the cover and refit vehicle, contact a PEUGEOT
the style cover when you have fi- dealer.
nished.
PEUGEOT will not accept respon-
sibility for the cost incurred in
repairing your vehicle or for recti-
fying the malfunctions resulting
from the installation of acces-
sories not supplied and not rec-
Fuse N Rating Functions ommended by PEUGEOT and not
installed in accordance with its
1* 50 A Fan unit. instructions, in particular where
the equipment in question con-
2* 30 A ESP/ABS pump motor. sumes more than 10 mil-
liamperes.
3* 30 A ESP/ABS solenoid valves.
4* 70 A Built-in Systems Interface supply. * The maxi-fuses provide addi-
5* 70 A Built-in Systems Interface supply. tional protection for the electrical
systems. All work on the maxi-
6* 20 A Heated seats. fuses and external fuses must
be carried out by a PEUGEOT
7* 30 A Ignition switch, power. dealer.
8* 70 A Power steering electro-pump unit.
External Rating Functions

fuse N
FV1* 20 A Single speed fan unit.
FV2* 30 A Dual speed fan unit.
29-09-2003
164
Fuse N Rating Functions

1 10 A Automatic gearbox reversing lights switch - Automatic gearbox starting inhibitor relay
control - Manual gearbox reversing lights switch - Vehicle speed sensor -
Water in diesel sensor.
2 15 A Canister solenoid valve - Fuel pump.
3 10 A Power steering control unit - ABS or ESP control unit.
4 10 A Injection control unit - Fan unit relay control - Additional heating relay control -
Automatic gearbox control unit - Automatic gearbox sequential control -
Automatic gearbox shiftlock relay.
5 15 A Particulate emission filter control unit.
6 15 A Front fog lamps.
7 20 A Headlamp wash pump.
8 20 A Fan unit relay control - Engine ECU supply -
Injection pump (Diesel).
9 15 A Left-hand dipped beam.
10 15 A Right-hand dipped beam.
11 10 A Right-hand main beam.
12 10 A Left-hand main beam.
13 15 A Horn.
14 10 A Front and rear wash-wipe pumps.
15 30 A Oxygen sensors - Exhaust gas recirculation solenoid valve - Ignition coil -
Diesel high pressure regulator - Injectors supply (petrol) - Pre-heat unit -
Air flow sensor (Diesel) - Engine ECU (Diesel) - Injection pump (Diesel) -
Diesel heater.
16 30 A Petrol engine air pump with automatic gearbox.
17 30 A Low/high speed front wiper.
18 40 A Air conditioning blower.
29-09-2003
165
CHANGING A WINDSCREEN ECONOMY MODE FUNCTION LOAD REDUCTION FUNCTION

WIPER BLADE
After the engine has stopped, with When driving, certain functions (air
Special front windscreen wiper the key in the accessories position, conditioning, heated rear screen,
position certain functions (windscreen wiper, heating system for passenger com-
electric windows, courtesy lights, partment of diesel vehicles, etc.)
Within one minute of switching audio equipment etc.) can only be may be switched off temporarily,
off the ignition, operate the used for a cumulative duration of depending on the level of battery
wipers stalk to position the wiper thirty minutes, to prevent discharging charge.
blades in the centre of the wind- the battery. Reactivation of these functions is
screen (maintenance position). Once the thirty minutes are over, the automatic, once the battery charge is
message "Economy mode active" sufficient.
appears on the multifunction display Note: at the risk of discharging the
Changing a wiper blade and the active functions are put on battery, the functions that have been
standby. switched off may be reactivated
Lift the wiper arm, then unclip the
blade and remove it. To resume the use of these functions manually.
immediately, start the engine and let
it run for a few seconds.
Fit the new blade and push back
the arm.
Note: the shortest blade is fitted on
the vehicle's right-hand windscreen
wiper arm.
To return the windscreen wipers

to their normal position, switch on
the ignition and operate the wiper
stalk.
A flat battery will prevent

the engine from starting.
29-09-2003
166
BATTERY
Before disconnecting
To charge the battery using a battery charger: the battery, you must
wait for 2 minutes after
Disconnect the battery, switching off the ignition.
Follow the instructions for use given by the battery charger manufacturer,
Never disconnect a terminal
Reconnect starting with the negative () terminal, when the engine is running.
Check that the terminals and connectors are clean. If they are covered with sul-
phate (white or greenish deposit), disconnect them and clean them. Never charge a battery without
first disconnecting the terminals.
To start the vehicle from another battery: Close the windows and sunroof
before disconnecting the battery.
Connect the red cable to the positive (+) terminals of the two batteries, If they do not operate normally
Connect one end of the green or black cable to the negative () terminal of the following reconnection of the bat-
slave battery, tery, they must be reintialised
(see sections "Reinitialisation of
Connect the other end of the green or black cable to an earth point on the bro- the electric windows" and
ken down vehicle, as far as possible from the battery, "Sunroof").
Operate the starter, let the engine run. After every reconnection of the
Wait for the engine to return to idle, then disconnect the cables. battery, switch on the ignition
and wait 1 minute before starting
to allow the electronic systems to
be initialised. If slight difficulties
are experienced after this,
please contact a PEUGEOT
dealer.
It is advisable to disconnect the battery if the vehicle is not to be used

for a period of more than one month.
29-09-2003
167
Special features of the

automatic gearbox
When towing with four wheels on the
ground, the following rules must be
obeyed:
lever in position N,
tow the vehicle at less than 30 mph

(50 km/h) over a maximum distance
of 30 miles (50 km).
do not add oil to the gearbox.
TOWING YOUR VEHICLE
Without lifting (4 wheels on the ground)

You must always use a tow bar.
The removable towing eye is inside the spare wheel.
Estate: The removable towing eye is inside the right-hand boot trim.
From the front:

Unclip the cover, by pressing the bottom part,
Screw in the towing eye as far as it will go.
From the rear:

Unclip the top of the cover using a coin,
Screw in the towing eye as far as it will go. When towing with the
engine switched off, there
is no braking or steering
Lifting (2 wheels only on the ground) assistance.
It is preferable to raise the vehicle with a professional lifting device.
29-09-2003
168
TOWING A TRAILER, Driving advice Tyres: Check the tyre pressures of

CARAVAN, BOAT etc. the towing vehicle and of the trailer,
Distribution of loads : Distribute the observing the recommended
load in the trailer so that the heaviest pressures.
Only use original PEUGEOT tow items are as close as possible to the
bars that have been tested and axle and the nose weight approaches
approved from the design stage of the maximum permitted without Braking: Towing increases the brak-
your vehicle. exceeding it. ing distance.
The tow bar must be fitted by a
PEUGEOT dealer.
Cooling : towing a trailer on a slope Lights: Check the electrical sig-
Your vehicle is primarily designed for increases the temperature of the nalling on the trailer.
transporting people and luggage but it coolant.
may also be used for towing a trailer.
As the fan is electrically controlled, Side wind: Take into acount the
Driving with a trailer subjects the its cooling capacity is not dependent
towing vehicle to more significant increased sensitivity to side wind.
on the engine speed.
stress and its driver must be particu-
larly careful. On the contrary, use a high gear to
lower the engine speed, and reduce
Air density decreases with altitude, your speed.
thus reducing engine performance.
Above 1 000 metres, the maximum The maximum towing load on a long
towing load must be reduced by 10 % slope depends on the gradient and
and so on for every 1 000 metres of the outside temperature.
altitude. In all cases, pay attention to the
The rear parking assistance function coolant temperature.
will be disarmed automatically when If the warning light comes on, stop
a towbar is fitted. the vehicle and switch off the engine
as soon as possible.
29-09-2003
169
REMOVING THE MAT

When removing the mat on the dri-
ver's side, push the seat as far back
as possible and unscrew the fixings.
When refitting, position the mat and
replace the fixings by pressing them in. FITTING ROOF BARS
Saloon: When fitting transverse roof
bars, use the four threads provided
for this purpose. To access these, Maximum authorised weight on
push the concealing flaps in the the roof rack, for a loading height
direction of the arrow. not exceeding 40 cm (with the
exception of bicycle carriers):
Estate: When fitting transverse roof 75 kg (saloon), 100 kg (estate).
bars, observe their positioning.
This is indicated by marks on each of
the longitudinal bars. If the height exceeds 40 cm,
adapt the speed of the vehicle
Use accessories approved by to the profile of the road
PEUGEOT and follow the manufac- to avoid damaging the roof bars
turer's fitting instructions. and the fixings on the roof.
29-09-2003
170
ENTERTAINMENT SCREEN KIT

This video assembly will enable the rear passengers to pass the time pleasantly
while watching their favourite film or playing their favourite game, by means, in
particular, of the connection of a DVD player or games console to the central sup-
port, fitted between the front seats.
The entertainment screen kit consists of:

a 16/9ths, 7 inch, LCD colour monitor with direction adjustment in the three
axes,
two high frequency, wireless, stereo headphones,
a removable support,
three audio/video sockets on the fixed base and in the glove compartment.
The monitor and the support can be removed and stored, each in their own pro-
tective cover.
The entertainment screen kit accepts all types of audio/video source, PAL/NTSC
compatible, such as: DVD player, camcorder, games console, ...
These sources are connected to the three audio/video sockets, AV1 in the glove
compartment or AV2 on the fixed base.
29-09-2003
171
The upper face of the monitor incor- Various controls are incorporated in
porates the following controls: the headphones:
1 - "POWER" button to switch the A - Housing for the two LR03 batteries.
monitor on/off. B - Headphones on/off button.
2 - "FUNC" button for selection of C - On/off indicator light.
the input source, AV1 or AV2.
D - Tuning frequency adjustment
3 - "WIDE" button to change the dis- control.
play format (normal, full screen,
wide, cinema). E - Headphones volume adjustment
control.
4 - "MENU" button for selection of
the menus and settings. The get the best out of the head-
phones, you must adjust their size to
5 - "" and "" buttons to change suit you, find their tuning frequency
the settings. by rotating control D, then adjust the
By pressing buttons 4 and 5, you can volume by rotating control E.
adjust the brightness, the contrast,
the colours, ...
For further details, refer to the oper-

ating manuals "Video kit operation"
and "VMA8582 7 inch LCD colour
monitor".
29-09-2003
172
ACCESSORIES FOR YOUR 307

For your PEUGEOT only use accessories and original parts approved by the manufacturer.
These accessories and parts are all adapted to your PEUGEOT, after being tested and approved for reliability and safety,
which PEUGEOT cannot guarantee for other products.
A wide choice of original accessories, approved by PEUGEOT, is available through the dealer network. They all carry
the PEUGEOT guarantee.
Safety : Anti-theft alarm, window engraving, wheel locks, first aid kit, warning triangle, safety jacket,
rear parking assistance...
Comfort : Telephone console, front centre arm rest, covers compatible with side air bags, mats, boot
tray, luggage net, door deflectors, CD storage, under shelf storage (saloon), side and rear
blinds...
Communication : Audio systems, telephone, hands-free kit, speakers, amplifiers, CD changer, satellite
navigation systems, entertainment screen kit, DVD player....
Customising : Spoiler (saloon), alloy wheels, trims, sport exhaust, aluminium or PVC door sills, mud
flaps...
Leisure : Tow bar, roof bars, roof box, snow chains, ski carrier, bicycle carrier on roof bars, tailgate
bicycle carrier (estate)...
Children : Booster seats and child seats...
Maintenance products : Screenwash, interior and exterior maintenance and cleaning products...
Before installing any electrical accessory on your vehicle, contact a PEUGEOT dealer.
29-09-2003
173
TECHNICAL DATA
PETROL ENGINES/COMPANY CAR
MODELS: 3CKFWB/T 3CKFUB 3CNFUB 3CNFUE 3CRFNB 3CRFNE

Model codes 3AKFWB/T 3AKFUB 3ANFUB 3ANFUE 3ARFNB 3ARFNE
3CKFWB 3EKFUB 3ENFUB 3ENFUE 3ERFNB 3ERFNE
3AKFWB 3CKFUC/IF 3CNFUC/IF 3CNFUF/IF 3CRFNC/IF 3CRFNF/IF
3EKFWB 3AKFUC/IF 3ANFUC/IF 3ANFUF/IF 3ARFNC/IF 3ARFNF/IF
3EKFUC/IF 3ENFUC/IF 3ENFUF/IF 3ERFNC/IF 3ERFNF/IF
ENGINES 1.4 litre 1.4 litre 16V 1.6 litre 16V 2 litre 16V
Cubic capacity (cm3) 1 360 1 360 1 587 1 997
Bore x stroke (mm) 75 x 77 75 x 77 78.5 x 82 85 x 88
EU standard maximum power
(kW) 55 65 80 100
Maximum power at engine
speed (rpm) 5 500 5 250 5 800 6 000
EU standard maximum torque (Nm) 120 133 147 190
Maximum torque at engine speed (rpm) 3 000 3 250 4 000 4 100
Fuel Unleaded Unleaded Unleaded Unleaded
Catalytic converter Yes Yes Yes Yes
Manual Manual Manual Automatic Manual Automatic

GEARBOX (5 speed) (5 speed) (5 speed) (4 speed) (5 speed) (4 speed)
OIL CAPACITIES (in litres)

Engine (with cartridge replacement) 3.25 3.05 3 3 4.25 4.25
Gearbox-Final drive 2 2 2 1.9
29-09-2003
174
TECHNICAL DATA
DIESEL ENGINES/COMPANY CAR

MODELS: 3C8HZB/T 3CRHYB/T 3CRHSB 3CRHRH
Model codes 3A8HZB/T 3ARHYB/T 3ARHSB 3ARHRH
3C8HZB 3CRHYB 3ERHSB 3ERHRH
3A8HZB 3ARHYB
3E8HZB 3ERHYB
ENGINES 1.4 litre Turbo HDI 2 litre turbo HDI 90 bhp 2 litre turbo HDI 110 bhp 2 litre turbo HDI 16V
Cubic capacity (cm3) 1 398 1 998 1 997 1 997
Bore x stroke (mm) 73.7 x 82 85 x 88 85 x 88 85 x 88
EU standard maximum power
(kW) 50 66 79 100
Maximum power at engine
speed (rpm) 4 000 4 000 4 000 4 000
EU standard maximum torque (Nm) 160 205 250 320
Maximum torque at engine speed (rpm) 1 900 2 000 1 750 2 000
Fuel Diesel Diesel Diesel Diesel
Catalytic converter Yes Yes Yes Yes
Particulate emission No No Yes Yes
GEARBOX Manual Manual Manual Manual

(5 speed) (5 speed) (5 speed) (6 speed)
OIL CAPACITIES (in litres)

Engine (with cartridge replacement) 4.3 4.5 4.5 5.25
Gearbox-Final drive 1.9 1.9 1.9 2.4
29-09-2003
175
TECHNICAL DATA
Saloon consumption In accordance with directive 99/100 [In MPG (litres/100 km)]
Engine Gearbox Model Circuit Circuit Circuit Emission

of codes Urban Inter-urban Mixed CO2 by
3C...3A... weight (g/Km)
1.4 litre Manual KFWB 32.4 (8.7) 51.4 (5.5) 42.2 (6.7) 159
1.4 litre 16V Manual KFUB
1.4 litre 16V Manual KFUC/IF
1.6 litre 16V Manual NFUB 29.7 (9.5) 48.7 (5.8) 39.2 (7.2) 169
1.6 litre 16V Manual NFUC/IF 28.2 (10.0) 48.7 (5.8) 38.1 (7.4) 174
NFUE
1.6 litre 16V Automatic NFUF/IF 25.9 (10.9) 45.6 (6.2) 35.8 (7.9) 189
RFNB
2 litre 16V Manual RFNC/IF 25.9 (10.9) 45.6 (6.2) 35.8 (7.9) 188
2 litre 16V Automatic RFNE 22.8 (12.4) 47.1 (6.0) 34.0 (8.3) 198
2 litre 16V Automatic RFNF/IF 22.2 (12.7) 45.6 (6.2) 32.8 (8.6) 204
1.4 litre Turbo HDI Manual 8HZB 51.4 (5.5) 70.6 (4.0) 62.8 (4.5) 120
2 litre Turbo HDI 90 bhp Manual RHYB 40.9 (6.9) 65.7 (4.3) 54.3 (5.2) 138
2 litre Turbo HDI 110 bhp Manual RHSB 40.4 (7.0) 67.2 (4.2) 54.3 (5.2) 138
2 litre Turbo HDI 16V Manual RHRH 39.8 (7.1) 62.8 (4.5) 52.4 (5.4) 142
Fuel consumption values correct at time of printing.

29-09-2003
176
TECHNICAL DATA
Estate consumption In accordance with directive 99/100 [MPG (litres/100 km)]
Engine Gearbox Model Urban Inter-urban Mixed Emission

codes circuit circuit circuit of CO2 by
weight (g/km)
1.4 litre Manual 3EKFWB 31.1 (9.0) 50.4 (5.6) 40.9 (6.9) 163
1.4 litre 16V Manual 3EKFUB
1.4 litre 16V Manual 3EKFUC/IF

3ENFUB
1.6 litre 16V Manual 3ENFUC/IF 28.5 (9.9) 44.8 (6.3) 36.7 (7.7) 178
3ENFUE
1.6 litre 16V Automatic 3ENFUF/IF 25.3 (11.2) 44.1 (6.4) 34.0 (8.3) 194
2 litre 16V Manual 3ERFNB
2 litre 16V Manual 3ERFNC/IF 24.6 (11.5) 44.8 (6.3) 34.0 (8.3) 194
2 litre 16V Automatic 3ERFNE 21.6 (13.1) 43.5 (6.5) 32.1 (8.8) 206
2 litre 16V Automatic 3ERFNF/IF 21.6 (13.1) 44.1 (6.4) 31.7 (8.9) 211
1.4 litre Turbo HDI Manual 3E8HZB 49.6 (5.7) 67.2 (4.2) 60.1 (4.7) 124
2 litre Turbo HDI 90 bhp Manual 3ERHYB 39.8 (7.1) 62.8 (4.5) 52.4 (5.4) 143
2 litre Turbo HDI 110 bhp Manual 3ERHSB 39.2 (7.2) 64.2 (4.4) 52.4 (5.4) 143
2 litre Turbo HDI 16V Manual 3ERHRH 38.7 (7.3) 60.1 (4.7) 50.4 (5,6) 148
Fuel consumption values correct at time of printing.

29-09-2003
177
TECHNICAL DATA
Weights and Towing loads (in kg) SALOON
3 and 5 DOOR PETROL/COMPANY CAR

Engine 1.4 litre 1.4 litre 16V 1.6 litre 16V
Gearbox Manual Manual Manual Automatic
Model codes: 3C 3A KFWB/T KFUB NFUB NFUE
KFWB KFUC/IF NFUC/IF NFUF/IF
Kerb weight 1 234 1 217 1 245 1 228 1 268 1 251 1 304 1 287
Gross vehicle weight (GVW) 1 659 1 642 2 639 1 620 1 693 1 676 1 729 1 712
Gross train weight (GTW*) 2 659 2 642 2 639 2 620 2 893 2 876 2 929 2 912
Unbraked trailer 590 605 620 610 610 625 630 643
Braked trailer (within GTW) 1 200 1 200 1 000 1 000 1 200 1 200 1 200 1 200
Maximum nose weight 60 60 60 60 60 60
3 and 5 DOOR DIESEL/COMPANY CAR

Engine 2 litre 16V
Gearbox Manual Automatic
Model codes: 3C 3A RFNB RFNE
RFNC/IF RFNF/IF
Kerb weight 1 294 1 277 1 330 1 313

Gross vehicle weight (GVW) 1 719 1 702 1 755 1 738
Gross train weight (GTW*) 3 019 3 002 3 055 3 038
Unbraked trailer 625 638 640 656
Braked trailer (within GTW) 1 300 1 300 1 300 1 300
Maximum nose weight 60 60 60 60
* The speed of a towing vehicle is limited to 60 mph (100 km/h).

29-09-2003
178
TECHNICAL DATA
Weights and Towing loads (in kg) SALOON
3 and 5 DOOR DIESEL/COMPANY CAR

Engine 1.4 litre Turbo HDI 2 litre Turbo HDI 90 bhp 2 litre Turbo HDI 110 bhp 2 litre Turbo HDI 16V
Gearbox Manual Manual Manual Manual
Model codes: 3C 3A 8HZB/T RHYB/T RHSB RHRH
8HZB RHYB
Kerb weight 1 271 1 254 1 335 1 318 1 371 1 354 1 427 1 410
Gross vehicle weight (GVW) 1 696 1 679 1 760 1 743 1 796 1 779 1 816 1 793
Gross train weight (GTW*) 2 836 2 819 3 060 3 043 3 136 3 119 3 216 3 193
Unbraked trailer 635 627 655 659 685 677 710 705
Braked trailer (within GTW) 1 140 1 140 1 300 1 300 1 340 1 340 1 400 1 400
Maximum nose weight 60 60 60 60 60 60

29-09-2003
179
TECHNICAL DATA
Weights and towing loads (in kg) ESTATE
PETROL
Engine 1.4 litre 1.4 litre 16V 1.6 litre 16V 2 litre 16V
Gearbox Manual Manual Manual Automatic Manual Automatic
Model codes: 3EKFWB 3EKFUB 3ENFUB 3ENFUE 3ERFNB 3ERFNE
3EKFUC/IF 3ENFUC/IF 3ENFUF/IF 3ERFNC/IF 3ERFNF/IF
Kerb weight 1 292 1 302 1 344 1 380 1 370 1 406

Gross vehicle weight (GVW) 1 800 1 694 1 850 1 875 1 880 1 880
Gross train weight (GTW)* 2 900 2 694 2 950 2 975 3 380 3 380
Unbraked trailer 645 650 670 690 685 700
Braked trailer (within GTW) 1 100 1 000 1 100 1 100 1 500 1 500
Maximum nose weight 60 60 60 72 72
DIESEL
Engine 1.4 litre Turbo HDI 2 litre Turbo HDI 90 bhp 2 litre Turbo HDI 110 bhp 2 litre Turbo HDI 16V
Gearbox Manual Manual Manual Manual
Model codes: 3E8HZB 3ERHYB 3ERHSB 3ERHRH
Kerb weight 1 332 1 403 1 434 1 481

Gross vehicle weight (GVW) 1 800 1 900 1 950 1 864
Gross train weight (GTW)* 2 900 3 400 3 450 3 264
Unbraked trailer 665 700 715 740
Braked trailer (within GTW) 1 100 1 500 1 500 1 400
Maximum nose weight 60 72 72

29-09-2003
180
TECHNICAL DATA
Saloon dimensions 3 and 5 door versions (in mm) Estate dimensions (in mm)
29-09-2003
181
TECHNICAL DATA
THE IDENTIFICATION FEATURES OF YOUR 307
A. Manufacturer's plate.
B. Serial number on the bodywork.
C. Serial number on the fascia.
D. Tyres and paint colour reference.
The label D on the driver's door pillar, near the hinges, indicates:
the wheel and tyre sizes,
the brands of tyres approved by the manufacturer,
the tyre pressures (the tyre pressure must be checked when the tyre is cold, at least once a month),
the paint colour reference.
29-09-2003

Manual Peugeot 307 PDF

Uploaded by

Copyright:

Available Formats

Manual Peugeot 307 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Manual Peugeot 307 PDF

Uploaded by

Copyright:

Available Formats

YOUR 307 AT A GLANCE 1

1- Driver's air bag. 15 - Side adjustable heating/

13 - Speaker (tweeter). 28 - Handbrake. * According to destination.

The remote control key Unlocking

STEERING WHEEL Vehicles fitted with a rear fog

Never drive with the

Take care not to trap the seat belts. 94

AIR BAGS Disarming the passenger Disarming check

ELECTRIC WINDOWS STEERING WHEEL

Safety auto-reverse: When the window is rising and meets

OPENING THE BONNET

FILLING WITH FUEL Inside the vehicle: Push the

Outside the vehicle: Lift

AUTOMATIC GEARBOX "PORSCHE TIPTRONIC SYSTEM"

AUTOMATIC AIR CONDITIONING

1 Air flow adjustment.

This point is determined by two parameters:

Example: the service is overdue by

Note: the service spanner may also

Zero re-set MAINTENANCE OF PARTS SUBJECT TO WEAR and a check of

MAINTENANCE CYCLE FOR YOUR 307 PETROL ENGINE

Arduous conditions of use (see corresponding section).

Intermediate visit included

MAINTENANCE CYCLE FOR YOUR 307 DIESEL

1st service at 6,000 miles

+ maintenance of particulate + maintenance of particulate

These services are to be carried out:

Arduous conditions of use (see corresponding section).

Intermediate visit included

ARDUOUS CONDITIONS OF USE

Continuous door-to-door use.

Other recommended products

Power steering FLUIDE DA PR 9730.A1

Brake fluid PEUGEOT DOT4

13 - ABS warning light.

1 - Rev counter. 22 - Diesel engine preheating

13 - ABS warning light.

14 - Air bag warning light.

15 - Passenger air bag disarming

17 -Service indicator, oil level and

18 - Trip recorder zero reset.

19 - Rear fog lamp indicator light.

20 - Electronic stability control

Battery charge Electronic stability To regenerate the filter, you are

Diesel Passenger air bag Seat belt not

Selector lever positions on the Automatic gearbox indicator

Park "SPORT" indicator light

"SNOW" indicator light

4th gear engaged

Instrument panel display Lighting

Oil level gauge fault

MULTI-FUNCTION Monochrome screen CT and

telematics (see "RT3 audio/ Parameter configuration

Stalk movement Function

Stalk movement Function

ADJUSTING THE VOLUME

Adjusting the bass

Adjusting the treble

Selecting radio mode