ICs for Audio Common Use

AN7513
1-W BTL audio power amplifier

Overview Unit: mm
The AN7513 is an audio power amplifier IC with 1-ch
output. The BTL (Balanced Transformer-Less) method can

0.9
1.0
provide fewer external parts and more easy design for ap- 1 8
plications.

9.20.2
2 7

1.3
0.5

1.5
3 6

2.54
4 5
Features 6.40.2
0.30.26

1-W output (8 ) with supply voltage of 5 V 3.350.2 3.890.2

On-chip standby function

On-chip volume function

Applications +0.1 5
.0
0.30 0
Televisions, radios, and personal computers 3 to 15 7.620.3

DIP008-P-0300K

Block Diagram

Ripple
VCC 5 rejection 1 Standby
circuit
Attenuator

6
Output
Thermal
shutdown
28 dB

8
Output
Attenuator
control
GND 7 28 dB
(for output)
2

4
Input

GND

Volume

Publication date: November 2001 SDC00034CEB 1

AN7513

Pin Descriptions
Pin No. Description
1 Standby (standby state if this pin is open.)
2 Input
3 Ground (for input)
4 Volume (max. volume if this pin is open.)
5 Supply voltage
6 + Output
7 Ground (for output ch.1)
8 Output

Absolute Maximum Ratings

Parameter Symbol Rating Unit
Supply voltage *2 VCC 14 V
Supply current ICC 1.0 A
Power dissipation *3 PD 541 mW
Operating ambient temperature *1 Topr 25 to +70 C
Storage temperature *1 Tstg 55 to +150 C
Note) *1: Except for the operating ambient temperature and storage temperature, all ratings are for Ta = 25C.
*2: At no signal
*3: The power dissipation shown is the value for Ta = 70C.

Recommended Operating Range

Parameter Symbol Range Unit
Supply voltage VCC 3.5 to 13.5 V

Electrical Characteristics at VCC = 5.0 V, RL = 8 , f = 1 kHz, Ta = 25C 2C

Parameter Symbol Conditions Min Typ Max Unit
Quiescent circuit current ICQ VIN = 0 mV, Vol. = 0 V 20 60 mA
Standby current ISTB VIN = 0 mV, Vol. = 0 V 1 10 A
Output noise voltage * VNO Rg = 10 k, Vol. = 0 V 0.10 0.4 mV[rms]
Voltage gain GV PO = 0.25 W, Vol. = 1.25 V 31 33 35 dB
Total harmonic distortion THD PO = 0.25 W, Vol. = 1.25 V 0.10 0.5 %
Maximum output power PO1 THD = 10%, Vol. = 1.25 V 0.7 1.0 W
Ripple rejection ratio * RR Rg = 10 k, Vol. = 0 V, 30 50 dB
VR = 0.5 V[rms], fR = 120 Hz
Output offset voltage VOFF Rg = 10 k, Vol. = 0 V 250 0 250 mV
Volume attenuation rate * Att PO = 0.25 W, Vol. = 0 V 70 85 dB
Intermediate voltage gain GVM PO = 0.25 W, Vol. = 0.6 V 20.5 23.5 26.5 dB
Note) *: In measuring, the filter for the range of 15 Hz to 30 kHz (12 dB/OCT) is used.

2 SDC00034CEB
 AN7513

Terminal Equivalent Circuits

Pin No. Pin name Equivalent circuit Voltage
1 Standby pin VCC 5V

30 k
To the
shock
sound
prevention
circuit
VRF

10 k
( VCC)
1
200

50 k
2 k

12 k
1/2 VCC

33 k

10 k
To the

5 k
constant
current
circuit

2 Input pin VREF1 (1.4 V) 1.4 V

VCC

100 A
50 A

50 A
30 k

1 k
2
500
1 k
1 k

3 GND 0V
3

4 Volume pin
VCC
50 A

1 k
12 k

SDC00034CEB 3
AN7513

Terminal Equivalent Circuits (continued)

Pin No. Pin name Equivalent circuit Voltage
5 VCC 5.0 V
6 + Output pin 2.15 V
VCC

200 6
50

1/2 VCC
800 20 k

7 GND 0V
7

8 Output pin 2.15 V

VCC

200 8
50

1/2 VCC
800 20 k

Usage Notes
Please avoid the short circuit to VCC , ground, or load short circuit.
Please connect the cooling fin with the GND potential.
The thermal shutdown circuit operates at about Tj = 150C. However, the thermal shutdown circuit is reset automati-
cally if the temperature drops.
Please carefully design the heat radiation especially when you take out high power at high VCC .
Please connect only the ground of signal with the signal GND of the amplifier in the previous stage.

4 SDC00034CEB
 AN7513

Technical Data
1. Package power dissipation
PD T a
1 000

900
Independent IC without a heat sink
800 Rth(j-a) = 148C/W
PD = 845 mW (25C)

Power dissipation PD (mW)

700

600

500

400

300

200

100

0
0 25 50 70 75 100 125 150

Ambient temperature Ta (C)

2. Example of PCB pattern

Out +

Out

VCC
8 7 6 5

GND

1 2 3 4

GND

Volume
VIN
Standby

SDC00034CEB 5
AN7513

Application Circuit Example

Out1
8 VCC

5
1

4
1.0 F
270 k
68 k

10 k
10 F

1 F

Standby VIN1 Volume

6 SDC00034CEB
Request for your special attention and precautions in using the technical information
and semiconductors described in this material
(1) An export permit needs to be obtained from the competent authorities of the Japanese Govern-
ment if any of the products or technologies described in this material and controlled under the
"Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan.
(2) The technical information described in this material is limited to showing representative character-
istics and applied circuit examples of the products. It does not constitute the warranting of industrial
property, the granting of relative rights, or the granting of any license.
(3) The products described in this material are intended to be used for standard applications or gen-
eral electronic equipment (such as office equipment, communications equipment, measuring in-
struments and household appliances).
Consult our sales staff in advance for information on the following applications:
Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment,
combustion equipment, life support systems and safety devices) in which exceptional quality and
reliability are required, or if the failure or malfunction of the products may directly jeopardize life or
harm the human body.
Any applications other than the standard applications intended.
(4) The products and product specifications described in this material are subject to change without
notice for reasons of modification and/or improvement. At the final stage of your design, purchas-
ing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to
make sure that the latest specifications satisfy your requirements.
(5) When designing your equipment, comply with the guaranteed values, in particular those of maxi-
mum rating, the range of operating power supply voltage and heat radiation characteristics. Other-
wise, we will not be liable for any defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, redundant design is recommended,
so that such equipment may not violate relevant laws or regulations because of the function of our
products.
(6) When using products for which dry packing is required, observe the conditions (including shelf life
and after-unpacking standby time) agreed upon when specification sheets are individually exchanged.
(7) No part of this material may be reprinted or reproduced by any means without written permission
from our company.

Please read the following notes before using the datasheets

A. These materials are intended as a reference to assist customers with the selection of Panasonic
semiconductor products best suited to their applications.
Due to modification or other reasons, any information contained in this material, such as available
product types, technical data, and so on, is subject to change without notice.
Customers are advised to contact our semiconductor sales office and obtain the latest information
before starting precise technical research and/or purchasing activities.
B. Panasonic is endeavoring to continually improve the quality and reliability of these materials but
there is always the possibility that further rectifications will be required in the future. Therefore,
Panasonic will not assume any liability for any damages arising from any errors etc. that may ap-
pear in this material.
C. These materials are solely intended for a customer's individual use.
Therefore, without the prior written approval of Panasonic, any other use such as reproducing,
selling, or distributing this material to a third party, via the Internet or in any other way, is prohibited.

2001 MAR
This datasheet has been download from:

www.datasheetcatalog.com

Datasheets for electronics components.