Scribd Logo
Upload

Welcome to Scribd!

  • 31 views

    Techtopics52rev0 X

    Uploaded by

    harmlesdragon
    Design technique

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Techtopics52rev0 X

    Uploaded by

    harmlesdragon
    31 views2 pages
    Design technique

    Original Title

    Techtopics52rev0 x

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Design technique

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    31 views2 pages

    Techtopics52rev0 X

    Uploaded by

    harmlesdragon
    Design technique

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    TechTopics No.

    52
    Revision 0
    TechTopics Date:Sept. 25, 2006

    TechTopics Topic: Insulation of Switchgear Terminations

    We occasionally receive queries from users or their installation contractors regarding the need for insulation
    of the users power connections to metal-clad switchgear. The answer is that the users power connections
    must be insulated to the same performance levels as are required of the switchgear itself. The users power
    connections are typically insulated with tape in accordance with the manufacturers instructions, or may be
    insulated with optional preformed boots available from most switchgear manufacturers.

    ANSI/IEEE C37.20.2 for metal-clad switchgear defines metal-clad as, among other things, switchgear in
    which the primary bus conductors and connections are covered with insulating material throughout (clause
    3.1.5.e). The standard goes on to explain the rationale for requiring that primary conductors and
    connections be insulated in clause 7.9, which says (in part)
    This insulating covering is a requirement of metal-clad switchgear (see 3.1.5) and is provided to
    minimize the possibility of communicating faults and prevent the development of bus faults that would
    result if foreign objects momentarily contacted bare bus. This insulating covering is usually only a part
    of the primary insulation system, and in such cases the outer surface of this insulating covering will
    not be at ground potential. It should not be assumed, therefore, that personnel can contact this
    insulating covering with complete safety.

    This paragraph contains multiple nuggets of wisdom on the subject of insulation in metal-clad switchgear,
    in general, and on insulation of users power terminations.

    Reduction of fault likelihood:


    ANSI metal-clad switchgear requires insulated primary conductors. It is usually assumed that this is to allow
    the equipment to be more compact, but this is only a minor consideration. The real intent of having
    insulated conductors in metal-clad switchgear is to reduce the likelihood of occurrence of arcing faults.
    There have been many technical papers that emphasize the value of insulated conductors in reducing the
    likelihood of an arcing fault.

    Insulation is a component of the insulation system:


    In ANSI/IEEE switchgear, the insulation covering is not the entire insulation system of the switchgear, but is
    actually one part of a coordinated system of insulation, supports, and the air surrounding the conductors.
    The insulation covering itself is required to withstand rated line-line voltage between the conductor and the
    outside surface of the insulation for one minute (clause 6.2.1.3 Test for bus-bar insulation). To understand
    this requirement in the context of the overall design, think of this requirement as a one-minute power
    frequency test for the insulation itself. For 15kV switchgear, this would require a one-minute test withstand
    of 15kV across the bus or conductor insulation. The complete equipment has a requirement of 36kV for the
    one-minute power frequency withstand voltage test. Therefore, the standards require that the insulation, by
    itself, have at least 15kV/36kV, or just over 40% of the total insulation capability of the system. This means
    that in 15kV switchgear, as much as 60% of the insulation integrity is contained in the air surrounding the
    conductors. So, if the users power terminations are not covered with insulation, something of vicinity of
    40% of the dielectric strength of the insulation system is lost.

    Outer surface of insulation not at ground potential:


    The last portion of the paragraph reminds the user of the standard that the outer surface of the insulation is
    not at ground potential, and is therefore not safe to touch. Energized insulated conductors in switchgear
    must be treated as energized conductors.

    2006 Siemens Power Transmission & Distribution, Inc. TechTopics No. 52


    PO Box 29503, Raleigh, NC 27626 Page 1
    Other considerations
    The dielectric capability of a switchgear design is a carefully considered balance between dielectric
    performance, manufacturing cost, equipment size, ease of assembly and installation, and a host of other
    factors. The manufacturer seeks to minimize the variations between various designs (e.g., between 1200A,
    2000A, 3000A, and 4000A configurations) and to maximize the use of standard components across various
    designs. Phase-phase conductor spacing is standardized in each manufacturers design, with the size of
    the conductor varying to suit the continuous current rating. Because of this, lower continuous current
    designs may appear to have sufficient clearance so that they do not require insulation of the users power
    terminations. However, this is unwise, as seemingly adequate phase-phase clearance between energized
    parts does not necessarily imply adequate phase-ground clearance.

    In addition, the manufacturer has to consider power frequency voltage withstand capability (as discussed
    earlier in this issue), and must also consider impulse withstand capability. The manufacturer conducts
    lightning impulse withstand tests to verify the performance of their designs. Equipment designed to have
    insulated user power terminations is not likely to meet the lightning impulse withstand performance levels of
    the design if the terminations are not insulated.

    Some users request special designs to accommodate uninsulated user power terminations, such as by
    installing insulating barriers between the phases and between the outer phases and ground in the users
    power termination areas. This can be done, but is generally undesirable for these reasons:
    Since the terminations would not be insulated, it causes the switchgear to fail to comply with IEEE
    C37.20.2 standards for metal-clad switchgear.
    Addition of barriers increases the cost of the equipment.
    The manufacturer may add barriers but may not have performed design tests to IEEE C37.20.2 to verify
    that the equipment meets the dielectric performance requirements of the standard, including both the
    power frequency (one-minute) withstand voltage and the lightning impulse withstand voltage levels.
    Addition of interphase / outerphase barriers increases the clutter in the termination area. If the barriers
    must be removed to provide access for examination of the main bus, the barriers make the operation
    more difficult, and may also make it less likely that the main bus area will be periodically inspected.

    Summary
    Insulated user power terminations are required by the standards for metal-clad switchgear
    Insulation reduces the likelihood of occurrence of arcing faults
    Insulation is required to meet the dielectric performance levels of the standards

    T. W. (Ted) Olsen
    Manager, Technology

    2006 Siemens Power Transmission & Distribution, Inc. TechTopics No. 52


    PO Box 29503, Raleigh, NC 27626 Page 2

    You might also like