TL072

TL072A - TL072B
LOW NOISE J-FET DUAL OPERATIONAL AMPLIFIERS

WIDE COMMON-MODE (UP TO VCC+) AND

DIFFERENTIAL VOLTAGE RANGE
LOW INPUT BIAS AND OFFSET CURRENT
LOW NOISE en = 15nV/Hz (typ)
OUTPUT SHORT-CIRCUIT PROTECTION
N
HIGH INPUT IMPEDANCE JFET INPUT DIP8
STAGE (Plastic Package)
LOW HARMONIC DISTORTION : 0.01% (typ)
INTERNAL FREQUENCY COMPENSATION
LATCH UP FREE OPERATION
HIGH SLEW RATE : 16V/s (typ)
D
SO8
(Plastic Micropackage)

DESCRIPTION ORDER CODE

Package
The TL072, TL072A and TL072B are high speed Part Number Temperature Range
JFET input dual operational amplifiers incorpo- N D
rating well matched, high voltage JFET and bipo- TL072M/AM/BM -55C, +125C
lar transistors in a monolithic integrated circuit. TL072I/AI/BI -40C, +105C
TL072C/AC/BC 0C, +70C
The devices feature high slew rates, low input bias
Example : TL072CN
and offset current, and low offset voltage temper-
N = Dual in Line Package (DIP)
ature coefficient. D = Small Outline Package (SO) - also available in Tape & Reel (DT)

PIN CONNECTIONS (top view)

1 - Offset null 1
1 8 2 - Inverting input 1
3 - Non-inverting input 1
2 7 4 - VCC-
-
5 - Non-inverting input 2
6 -Inverting input 2
3 + - 6 7 - Output 2
8 - VCC+
4 + 5

March 2001 1/10

TL072 - TL072A - TL072B

SCHEMATIC DIAGRAM

VCC

Non-inverting
input
Inverting
input
1 0 0
2 0 0
Output

1 0 0
30k 1/2 TL072

8.2k

1.3k 35k 1.3k 35k 1 0 0

VCC

ABSOLUTE MAXIMUM RATINGS

Symbol Parameter TL072M, AM, BM TL072I, AI, BI TL072C, AC, BC Unit
VCC Supply voltage - note 1) 18 V
Vi Input Voltage - note 2) 15 V
Vid 3) 30 V
Differential Input Voltage - note
Ptot Power Dissipation 680 mW
Output Short-circuit Duration - note 4) Infinite
Toper Operating Free-air Temperature Range -55 to +125 -40 to +105 0 to +70 C
Tstg Storage Temperature Range -65 to +150 C
1. All voltage values, except differential voltage, are with respect to the zero reference level (ground) of the supply voltages where the zero reference
level is the midpoint between VCC + and VCC -.
2. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 volts, whichever is less.
3. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal.
4. The output may be shorted to ground or to either supply. Temperature and/or supply voltages must be limited to ensure that the dissipation rating
is not exceeded

2/10
 TL072 - TL072A - TL072B

ELECTRICAL CHARACTERISTICS
VCC = 15V, Tamb = +25C (unless otherwise specified)
TL072I,M,AC,AI,AM,
TL072C
Symbol Parameter BC,BI,BM Unit
Min. Typ. Max. Min. Typ. Max.
Input Offset Voltage (Rs = 50) mV
Tamb = +25C TL072 3 10 3 10
TL072A 3 6
Vio TL072B 1 3
Tmin Tamb Tmax TL072 13 13
TL072A 7
TL072B 5
DVio Input Offset Voltage Drift 10 10 V/C
Input Offset Current - note 1)
Iio Tamb = +25C 5 100 5 100 pA
Tmin Tamb Tmax 4 10 nA
Input Bias Current -note 1
Iib Tamb = +25C 20 200 20 200 pA
Tmin Tamb Tmax 20 20 nA
Large Signal Voltage Gain (RL = 2k, Vo = 10V) V/mV
Avd Tamb = +25C 50 200 25 200
Tmin Tamb Tmax 25 15
Supply Voltage Rejection Ratio (RS = 50) dB
SVR Tamb = +25C 80 86 70 86
Tmin Tamb Tmax 80 70
Supply Current, no load mA
ICC Tamb = +25C 1.4 2.5 1.4 2.5
Tmin Tamb Tmax 2.5 2.5

Vicm 11 +15 11 +15 V

Input Common Mode Voltage Range
-12 -12
Common Mode Rejection Ratio (RS = 50) dB
CMR Tamb = +25C 80 86 70 86
Tmin Tamb Tmax 80 70
Output Short-circuit Current mA
Ios Tamb = +25C 10 40 60 10 40 60
Tmin Tamb Tmax 10 60 10 60
Output Voltage Swing V
Tamb = +25C RL = 2k 10 12 10 12
Vopp RL = 10k 12 13.5 12 13.5
Tmin Tamb Tmax RL = 2k 10 10
RL = 10k 12 12
Slew Rate (Tamb = +25C) V/s
SR
Vin = 10V, RL = 2k, CL = 100pF, unity gain 8 16 8 16

tr
Rise Time (Tamb = +25C) s
Vin = 20mV, RL = 2k, CL = 100pF, unity gain 0.1 0.1
Overshoot (Tamb = +25C) %
Kov
Vin = 20mV, RL = 2k, CL = 100pF, unity gain 10 10
Gain Bandwidth Product (Tamb = +25C) MHz
GBP
Vin = 10mV, RL = 2k, CL = 100pF, f= 100kHz 2.5 4 2.5 4
Ri Input Resistance 1012 1012

3/10
TL072 - TL072A - TL072B

TL072I,M,AC,AI,AM,
TL072C
Symbol Parameter BC,BI,BM Unit
Min. Typ. Max. Min. Typ. Max.
Total Harmonic Distortion (Tamb = +25C)
%
THD f= 1kHz, RL = 2k,CL = 100pF, Av = 20dB,
0.01 0.01
Vo = 2Vpp
Equivalent Input Noise Voltage nV
en ------------
RS = 100, f = 1KHz 15 15 Hz
m Phase Margin 45 45 degrees
Channel separation dB
Vo1/Vo2
Av = 100 120 120
1. The input bias currents are junction leakage currents which approximately double for every 10C increase in the junction temperature.

4/10
 TL072 - TL072A - TL072B

MAXIMUM PEAK-TO-PEAK OUTPUT MAXIMUM PEAK-TO-PEAK OUTPUT

VOLTAGE versus FREQUENCY VOLTAGE versus FREQUENCY

MAXIMUM PEAK-TO-PEAK OUTPUT MAXIMUM PEAK-TO-PEAK OUTPUT

VOLTAGE versus FREQUENCY VOLTAGE versus FREE AIR TEMP.

MAXIMUM PEAK-TO-PEAK OUTPUT MAXIMUM PEAK-TO-PEAK OUTPUT

VOLTAGE versus LOAD RESISTANCE VOLTAGE versus SUPPLY VOLTAGE

30
MAXIMUM PEAK-TO-PEAK OUTPUT

RL = 10 k
25
Tamb = +25C

20
VOLTAGE (V)

15

10

0 2 4 6 8 10 12 14 16
SUPPLY VOLTAGE ( V)

5/10
TL072 - TL072A - TL072B

INPUT BIAS CURRENT versus FREE AIR LARGE SIGNAL DIFFERENTIAL VOLTAGE
TEMPERATURE AMPLIFICATION versus FREE AIR TEMP.

100 1000
V CC = 15V
400
INPUT BIAS CURRENT (nA)

10 200

DIFFERENTIAL VOLTAGE
AMPLIFICATION (V/V)
100

1 40
20
10 V CC = 15V
0.1 V O = 10V
4
2 R L = 2k

0.01 1
-50 -25 0 25 50 75 100 125 -75 -50 -25 0 25 50 75 100 125

TEMPERATURE (C) TEMPERATURE (C)

LARGE SIGNAL DIFFERENTIAL VOLTAGE TOTAL POWER DISSIPATION versus FREE AIR
AMPLIFICATION AND PHASE SHIFT versus TEMPERATURE
FREQUENCY

250
DIFFERENTIAL VOLTAGE

100 225 V CC = 15V

TOTAL POWER DISSIPATION (mW)

180
AMPLIFICATION (V/V)

DIFFERENTIAL
VOLTAGE
200 No signal
PHASE SHIFT AMPLIFICATION No load
(right scale) 175
(left scale)
150
10 90 125
R = 2kW 100
L
C L = 100pF 75
1 V CC = 15V 0 50
T amb = +125C 25
0
100 1K 10K 100K 1M 10M
-75 -50 -25 0 25 50 75 100 125
FREQUENCY (Hz)
TEMPERATURE (C)

SUPPLY CURRENT PER AMPLIFIER versus COMMON MODE REJECTION RATIO versus
FREE AIR TEMPERATURE FREE AIR TEMPERATURE

2.0 89
1.8 V CC = 15V R L = 10 k
COMMON MODE MODE REJECTION

1.6 No signal 88
VC C = 15V
SUPPLY CURRENT (mA)

1.4 No load
87
1.2
RATIO (dB)

1.0 86
0.8
0.6 85
0.4 84
0.2
0 83
-75 -50 -25 0 25 50 75 100 125
-75 -50 -25 0 25 50 75 100 125
TEMPERATURE (C) TEMPERATURE (C)

6/10
 TL072 - TL072A - TL072B

VOLTAGE FOLLOWER LARGE SIGNAL PULSE OUTPUT VOLTAGE versus ELAPSED TIME
RESPONSE

28
INPUT AND OUTPUT VOLTAGES

6
24
4 OUTPUT OVERSHOOT

OUTPUT VOLTAGE (mV)

INPUT 20 90%

2 16
0
(V)

12
VCC= 15V
8
-2 R L = 2 kW V = 15V
CC
C L= 100pF 4 R L = 2k
-4 10%
Tamb = +25C 0 Tamb = +25C
-6 tr
0 0.5 1 1.5 2 2.5 3 3.5 -4
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7
TIME (m s) TIME ( s)

EQUIVALENT INPUT NOISE VOLTAGE versus TOTAL HARMONIC DISTORTION versus

FREQUENCY FREQUENCY

70 1
VCC = 15V V VCC = = 15V 15V
TOTAL HARMONIC DISTORTION

60 CC
A V = 10 0.4
A AV V= =1 1
EQUIVALENT INPUT NOISE

50 R S = 100 V VO O(rms) = =6V6V

VOLTAGE (nV/VHz)

0.1 (rms)
T amb = +25C T amb= =+25C
T amb +25C
40 0.04
(%)

30
0.01
20
0.004
10
0 0.001
10 40 100 400 1k 4k 10k 40k 100k 100 400 1k 4k 10k 40k 100k
FREQUENCY (Hz) FREQUENCY (Hz)

7/10
TL072 - TL072A - TL072B

PARAMETER MEASUREMENT INFORMATION

Figure 1 : Voltage Follower Figure 2 : Gain-of-10 Inverting Amplifier

10k
1k
eI -
1/2
TL072 eo

RL CL = 100pF

TYPICAL APPLICATIONS
100KHz QUADRUPLE OSCILLATOR

18k *
1N 4148 -15V

18pF 1k
18pF

-
1/2 88.4k
TL072 -
1/2
88.4k 6 cos t
TL072
6 sin t
1k
18pF

88.4k
1N 4148
18k *

+15V

* These resistors values may be adjusted for a symmetrical output

8/10
 TL072 - TL072A - TL072B

PACKAGE MECHANICAL DATA

8 PINS - PLASTIC DIP

Millimeters Inches
Dim.
Min. Typ. Max. Min. Typ. Max.
A 3.32 0.131
a1 0.51 0.020
B 1.15 1.65 0.045 0.065
b 0.356 0.55 0.014 0.022
b1 0.204 0.304 0.008 0.012
D 10.92 0.430
E 7.95 9.75 0.313 0.384
e 2.54 0.100
e3 7.62 0.300
e4 7.62 0.300
F 6.6 0260
i 5.08 0.200
L 3.18 3.81 0.125 0.150
Z 1.52 0.060

9/10
 TL072 - TL072A - TL072B

PACKAGE MECHANICAL DATA

8 PINS - PLASTIC MICROPACKAGE (SO)

Millimeters Inches
Dim.
Min. Typ. Max. Min. Typ. Max.
A 1.75 0.069
a1 0.1 0.25 0.004 0.010
a2 1.65 0.065
a3 0.65 0.85 0.026 0.033
b 0.35 0.48 0.014 0.019
b1 0.19 0.25 0.007 0.010
C 0.25 0.5 0.010 0.020
c1 45 (typ.)
D 4.8 5.0 0.189 0.197
E 5.8 6.2 0.228 0.244
e 1.27 0.050
e3 3.81 0.150
F 3.8 4.0 0.150 0.157
L 0.4 1.27 0.016 0.050
M 0.6 0.024
S 8 (max.)

10/10