Scribd
Upload
220 views1 page

Connection Design - CTL Observation

The document provides design calculations for a connection between a UB254x146x31 member and a connecting plate using 3 bolts of 16mm diameter and A490 grade. It calculates the shear, tension and bearing capacities of the bolts. It also checks the weld thickness and web thickness of the UB section for shear rupture. The calculations establish that the bolt capacities exceed the design forces from STAAD and all thickness checks are satisfied.

Uploaded by

nvnagaraju
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
220 views1 page

Connection Design - CTL Observation

The document provides design calculations for a connection between a UB254x146x31 member and a connecting plate using 3 bolts of 16mm diameter and A490 grade. It calculates the shear, tension and bearing capacities of the bolts. It also checks the weld thickness and web thickness of the UB section for shear rupture. The calculations establish that the bolt capacities exceed the design forces from STAAD and all thickness checks are satisfied.

Uploaded by

nvnagaraju
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

TITLE:CONNECTIONDESIGNFOR

PROJECT:1061_KSA CLIENT:CTL
UB254x146x31
**
UB254x146x31
Include sketch to as per sample
** INPUTDATA
** Nominaldiameterofconnectionbolt d = 16 mm
** Holediameterofconnectionbolt d0 = 18
** Gradeofbolts = A490(groupA) Class
** FactoredtensileforcefromSTAAD (Ft) = 170.00 KN
** FactoredshearforcefromSTAAD (Fs) = 2.00 KN
** FactoredCompressionforcefromSTAAD (Fc) = 0.00 KN
** No'sofboltsrequired (n) = 3.00 No's
2
** Ultimatetensilestrengthofbolt (fub) = 780 N/mm
2
** Ultimateshearstrengthofbolt (fub) = 469 N/mm
2
** Yieldstrengthofplate (fy) = 275 N/mm
2
** Ultimatestrengthofplate (fu) = 430 N/mm
** Thicknessofconnectingplate t = 10 mm
** DepthofmemberUB254x146x31 H = 254 mm
** Enddistance (e) = 25 mm
** Pitchdistance (p) = 40 mm
** WebthicknessofUB254x146x31bearingcheck (tw) = 6 mm

** ShearcapacityofboltA490(groupA) ACI36010SecJ3,clause6.0 Show working


Establish Shear governs over bearing
formulae with
** Shearforceperbolt strength (Vsb) = 56.67 KN values
** Numberofshearplaneswiththreadsinterceptingtheshearplane (nn) =1
2
** Nominalplainshankareaofthebolt (Agv) = 201.06 mm
Where is this values
defined on this sheet
** Shearcapacityofbolt=xRnvxAb,=0.75 (Vnsb) = 70.72 KN
**
Designratioforshearcapacity 1.25 OK

** TensioncapacityofboltA490(groupA) ACI36010SecJ3,clause6.0
** Tensionforceperbolt = 56.667 kN
** UshearLegfactorU=1x/L SecD3 Give Stress ratio = 0.93 mm
** Netarea(An)=0.850xAg
for combine = 170.90 Sq.mm.
** EffectiveAreaAe=AnxU
Shear for Tension = 158.49 Sq.mm.
Tensilecapacityofbolt=xFntxAe= 0.75 = 92.72 kN
** DesignratioforTensionCapacity" 2.80 OK

** ShearruptureoftheGirderwebattheweld ACI36010SecJ4.2
tmin=3.09D/Fu(Eq.9.2inimp) Thkofweld 6 mm = 0.32 mm
Conectingmemberwebthickness = 6 mm
OK

Include the following checks in above calculation

1. Maximum thickness 8. Weld thickness at the web


2. Bolt bearing on plate
3. Shear Yielding of plates
4. Shear Rupture of plate
5. Block Shear of plate
6. Local Buckling of plate
7. Flexural Rupture of plate

You might also like