Improving Sound Insulation in Homes: WWW - Bre.co - Uk/acoustics

BRE Acoustics
Garston, Watford, Herts, WD25 9XX

T 01923 664500 F 01923 664095 E [email protected]
www.bre.co.uk/acoustics
IMPROVING SOUND INSULATION IN HOMES
Many people are bothered by neighbour noise. The problem can occur in
any type of existing or new built house or flat where there is a common
separating wall or floor. Poor quality conversions or building work
(flats, lofts, extensions etc.) frequently cause noise complaints from residents.
In flats converted before June 1992 there may have been little or no sound insulation
improvement undertaken on the floor. If this is the case, upgrading the floor is likely
to lead to significant improvements. Conversions carried out after July 2003 should
already have been tested and shown to have achieved the Building Regulation
performance standards (Approved Document E, ADE1) for sound insulation. Similarly
all relevant building elements used in the construction of new houses built from July
2004 should have been sound tested or approved by Robust Details Ltd2.
You may be bothered by your neighbour’s noise because:

• you are unusually sensitive to noise
• your neighbour behaves unreasonably
• the sound insulation between your homes is poor
While everybody sometimes hears some noise such as raised voices, laughter or
occasional loud music, you should not normally be able to hear your neighbour’s
ordinary conversation or television. In some cases you may wish to have the sound
insulation tested to determine whether the floor or wall is performing as it should be
(particularly if legal action is anticipated). BRE provides a UKAS accredited sound
testing service and can undertake this for you, call 01923 664500 to discuss
your requirements or e-mail [email protected]. Alternatively you may prefer
to attempt to improve the sound insulation directly either by employing a builder or
taking a DIY approach. This document outlines some of the principals of sound
insulation and their application to DIY measures.
First of all you have to decide how the

sound is travelling into your home. It
may be coming directly through the
separating wall or floor or it may be
coming along another indirect route
(called a flanking path). The most
common such path is the inner leaf of
an external cavity wall. Some
examples of flanking paths are shown
in Figure 1. Direct and indirect sound
can together contribute to a noise
problem.
Figure 1. Transmission paths for airborne sound through

rooms in a pair of flats separated by a timber floor
Page 1 of 4 www.bre.co.uk/acoustics
Problems with airborne and structure borne sound are often associated
both with direct transmission through a floor and flanking transmission
via supporting walls and other associated structures. It is essential
to establish if your problem is due to direct transmission, flanking
transmission or a combination of both so that the most effective
remedial treatment can be chosen.
The unwanted noise travelling along direct and flanking paths makes the building
structure vibrate and this causes the sound to radiate into your room. One solution is
to build another wall or ceiling beside the original, but not connected to it (often called
an independent wall or ceiling). A basic description of this treatment is given below.
There are two distinct types of noise to consider for noise coming through floors.
Impact noise, (for example footsteps directly on the floor above) and airborne noise,
(for example speech and music). Remedial treatment can be applied to the ceiling
below, the floor above or a combination of both.
Remedial Treatment: Walls

The following steps for construction are
suggested, see Figure 2:
• build a studwork frame, attached to

the ceiling and floor but not fixed to
the original wall
• hang mineral wool inside the cavity,
and tack between the studs or to a
batten on the wall
• line the studwork with two layers of
plasterboard, (make sure the joints
between the sheets in the first and
second layer do not coincide)
• seal the perimeter and all other
sound paths with flexible sealant
•
Figure 2. Wall improvement layout of studwork and
plasterboard
Remedial Treatment: Ceilings

The principle used in the wall treatment can be equally applied to ceilings, the idea
being to build a new ceiling below the existing one. The following steps for
construction are suggested, see Figure 3:
• attach wall plates to the walls to give the

shortest room span and run new ceiling
joists between them
• fix mineral wool between the new ceiling
joists, or drape it over them
• line with two plasterboard layers, making
sure the joints between the sheets in the
first and second layer do not coincide
• seal the perimeter and all other sound
paths with flexible sealant
Figure 3. Independent ceiling layout
In some situations there may be insufficient ceiling height to
accommodate new full size timber joists, or restrictions on the depth
of the wall linings. For timber structures, the plasterboard layers may be
attached to the joists or studs using resilient bars (specialised metal
fixings) which still give some isolation from the main wall or ceiling
structure but may not be as effective as a fully independent partition.
Specialised metal frame ceiling systems are also available which often
make use of resilient hangers to help isolate new ceilings from the
structure above. For masonry constructions, alternative solutions as
detailed in ADE1 may be more effective (seek further advice).
Remedial Treatment: Floors

If access to the ceiling is not possible, another solution is to construct a floating
platform floor in the room above which isolates the walking surface from the basic
floor structure below. This should significantly reduce the impact noise and may also
help to reduce the airborne noise. It is essential to check that the joists can carry the
increased floor loads satisfactorily.
The following steps are suggested, see Figure 4:
• remove original floor and skirting

boards and insert glass fibre or rock
wool quilt between the joists.
• refit the floor boarding and lay
25mm of glass fibre or rock wool (for
this layer a density between 60 and
80 kg/m3 is required) and cover with
19mm plasterboard, laid loose with
a gap at the perimeter walls.
• glue, (not nail), a top surface of
tongue and grooved chipboard of
not less than 18mm thick, leaving
perimeter gap of 10mm.
• seal the perimeter and all other
sound paths with flexible sealant
Figure 4. Floating floor improvement layout
• it is important that the floating layer is not bridged by nailing into the boards below
or re-fitting skirting boards too tightly to the surface (a flexible foam strip is often
inserted around the edge gap of the floor to prevent this).
This method will raise the floor by about 65mm so adjustments to doors, stairs and
other fittings may need to be taken into account.
Other types of proprietary flooring systems are now available including resilient
battens that support the walking surface and resilient foam layers, these vary
considerably in performance and price.
A more in-depth description of wall & floor treatments and other information can be
found in Approved Document E of the Building Regulations1. It is recommended that
you read this publication before starting any building work.
Provided that the sound is mainly entering your home through a direct
path then the correct use of the constructions explained above
should reduce it substantially. However, there is always a risk that
the treatment of a wall or floor alone will not be sufficient. A more
thorough acoustic investigation may be necessary before the
appropriate remedial measures can be decided upon.
Footnote: walls, floors and ceilings

A number of manufacturers now produce a range of systems designed to improve
sound insulation in homes, the effectiveness of these will varying depending on the
situation in which they are installed. If such products are to be used, detailed
information on the likely sound insulation performance when installed in your
property should be requested from the supplier. You are advised to give careful
consideration to the data supplied by a manufacturer before using a proprietary
product.
Do remember that remedial work to improve the sound insulation can result in
considerable weight being added to the structure of a property. Thus it is essential to
check that the ceiling or floor joists can carry the increased loads satisfactorily.
Further fee based consultancy advice on acoustic design can be provided by

BRE, call 01923 664500 to discuss your requirements or e-mail
[email protected].
Specific publications referred to in this leaflet are:

1. Approved Document E of the Building Regulations (2003 Edition)
(see http://www.planningportal.gov.uk/england/professionals/en/4000000000263.html)
2. Robust Details Part E, Resistance to the passage of sound
(see www.robustdetails.com )

Improving Sound Insulation in Homes: WWW - Bre.co - Uk/acoustics

Uploaded by

Copyright:

Available Formats

Improving Sound Insulation in Homes: WWW - Bre.co - Uk/acoustics

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Improving Sound Insulation in Homes: WWW - Bre.co - Uk/acoustics

Uploaded by

Copyright:

Available Formats

BRE Acoustics

Garston, Watford, Herts, WD25 9XX

IMPROVING SOUND INSULATION IN HOMES

You may be bothered by your neighbour’s noise because:

First of all you have to decide how the

Figure 1. Transmission paths for airborne sound through

Remedial Treatment: Walls

• build a studwork frame, attached to

Remedial Treatment: Ceilings

• attach wall plates to the walls to give the

Remedial Treatment: Floors

The following steps are suggested, see Figure 4:

• remove original floor and skirting

Figure 4. Floating floor improvement layout

Footnote: walls, floors and ceilings

Further fee based consultancy advice on acoustic design can be provided by

Specific publications referred to in this leaflet are:

You might also like