DATA SHEET

In-Line Balanced
Pressure Proportioners
Models CIBP, CIBP-M

Features
nSix standard sizes to handle a wide range of flows with 009829
minimal friction loss
nSpool valve design ensures accurate pressure regulation and The spool valve senses the foam concentrate pressure and auto-
rapid response to changes in flow demand matically adjusts to balance it with the water pressure. A duplex
nBrass foam concentrate piping with stainless steel trim acces- pressure gauge provides a reading of the foam concentrate and
sories standard for use in marine applications and other corro- water pressures. The foam concentrate then enters the propor-
sive environments tioner, where a built-in orifice regulates the flow of pressurized
foam concentrate entering the water stream.
n Compatible with all CHEMGUARD foam concentrates
n Choice of unpainted brass or standard red paint finish The units are available in six standard sizes to supply proportion-
ers ranging from 2 in. to 8 in. with flow rates from 30 gpm to
5,500gpm (114 Lpm to 20,820 Lpm) as listed under the System
Information Table. Each unit consists of a foam proportioner,
Application pressure balancing spool valve, duplex gauge, various control
CHEMGUARD In-Line Balanced Pressure Proportioners are valves, drain valves, check valves, interconnecting brass pipe
used with an atmospheric foam concentrate tank and a positive and fittings, stainless steel braid flexible pressure sensing hoses,
displacement foam concentrate pump. In-line balanced pressure and valve identification nameplates. The CIBP-M models are
proportioners are designed to accurately control the flow of a also provided with a manual foam balancing valve. The in-line
foam liquid concentrate into a water stream over a wide range balanced pressure proportioner is factory pressure tested after
of flow rates and pressures. Advantages of the in-line balanced being assembled.
pressure proportioner include the following:
nMultiple proportioning devices can be used with a single pres-
surized foam concentrate supply.
Approvals
The CHEMGUARD CIBP in-line proportioner is UL Listed with
nFoam concentrate can be proportioned near the discharge
various CHEMGUARD foam concentrates. For specific concen-
devices while the foam concentrate storage tank and pump are
trates and corresponding flow ranges, consult Tyco Fire
placed in a remote location.
Protection Products Technical Services.
nWater supply pressure can vary at proportioners under
simultaneous operation without affecting foam solution
concentration. Specifications
nVarious sizes of in-line balanced pressure proportioners can be The in-line balanced pressure proportioner assembly shall
combined in a single system to best suit the flow requirements contain all necessary components including: foam proportioner,
of each hazard area. pressure balancing spool valve, duplex gauge, control valves,
drain valves, check valves, interconnecting brass pipe, and valve
identification nameplates.
Description Balancing shall be accomplished through the use of a spool-type
The in-line balanced pressure proportioning system functions pressure balancing valve. This valve shall sense foam concen-
by maintaining an equal pressure in the foam concentrate and trate and water inlet pressures at the outer ends of a dumbbell-
water inlets to the proportioner. This balancing ability allows the shaped piston, and shall react to pressure changes by covering
proportioner to be used over a wide range of flows and pres- or uncovering the foam supply port to the proportioner. The
sures. The system will also respond quickly and accurately to balancing valve shall be low zinc (less than 15%) brass construc-
changes in the water inlet pressures and flow rates. tion with a bronze piston and Buna-N rubber O-rings and seals.
The in-line balanced pressure proportioner shall be completely
The system utilizes a positive displacement foam pump to pres- pressure tested by the manufacturer.
surize foam concentrate within the supply manifold. A pressure
control valve, located in the return line that leads to the foam Interconnecting foam concentrate piping shall be of brass
concentrate storage tank, is set to maintain a regulated pres- construction. Pressure sensing hoses shall be TEFLON1 material
sure in the supply manifold that is higher than the pressure in with a stainless braid cover and permanently attached brass
the water supply line. The foam concentrate that is not required couplings. Valve nameplates shall be provided, and shall specify
by the proportioner is returned to the atmospheric storage tank valve function and normal operating position. The foam
through the pressure control valve. concentrate ball valve shall have a ring pin and chain for
securing the ball valve in the operating position.

Copyright 2016 Tyco Fire Products LP. / All rights reserved.

www.chemguard.com /+1-817-473-9964/ Form No. CG-2015145
System Information Table
The following table lists the nominal flow range for each proportioner size. For flow ranges using specific concentrates, consult Tyco Fire
Protection Products Technical Services.
Model Model Model Model Model Model
CIBP-2/CIBP-2M CIBP-2 1/2/CIBP-2 1/2M CIBP-3/CIPB-3M CIBP-4/CIBP-4M CIBP-6/CIBP-6M CIBP-8/CIBP-8M
Proportioner Size 2 in. 2 1/2 in. 3 in. 4 in. 6 in. 8 in.
Nominal Flow 30-300 35-400 70-800 200-1600 300-3400 500-5500
Range gpm
Nominal Flow (114-1136) (132-1514) (265-3028) (757-6057) (1136-12870) (1892-20819)
Range (Lpm)
In-line balanced pressure proportioner systems will proportion slightly higher concentrations at the low end of the nominal flow range.
Note: Listed Nominal Flow Ranges do not apply for Alcohol Resistant Concentrate.

In-Line Balanced Pressure Proportioners (Models CIBP-2 to CIBP-8)

Model CIBP-2 Model CIBP-2 1/2 Model CIBP-3 Model CIBP-4 Model CIBP-6 Model CIBP-8
in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) in. (mm)
Dimension A 17 (430) 18 1/2 (470) 18 1/4 (460) 22 1/2 (570)
Dimension B 16 (410) 16 (410)
Dimension C 16 3/4 (430) 16 3/4 (430) 16 3/4 (430) 16 3/4 (430) 16 3/4 (430) 20 (510)
Dimension D 9 (230) 9 (230) 9 3/4 (250) 10 1/2 (270) 12 (310) 14 (360)
Dimension E 1 3/4 (45) 1 3/4 (45) 1 3/4 (45) 1 3/4 (45) 1 3/4 (45) 2 3/16 (55)
Dimension F 1 NPT 1 NPT 1 NPT 1 1/2 NPT 1 1/2 NPT 2 NPT
Dimension G 2 NPT 2 1/2 NPT 3* 4* 6* 8*

C
E D

G G

B 001172

In-Line Balanced Pressure Proportioners With Manual Foam Balancing Valve

(Models CIBP-2M To CIBP-8M)
Model CIBP-2M Model CIBP-2 1/2M Model CIBP-3M Model CIBP-4M Model CIBP-6M Model CIBP-8M
in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) in. (mm)
Dimension A 25 1/2 (650) 28 1/2 (720) 28 (710) 32 3/8 (820)
Dimension B 24 1/2 (620) 24 1/2 (620)
Dimension C 16 3/4 (430) 16 3/4 (430) 16 3/4 (430) 16 3/4 (430) 16 3/4 (430) 20 (510)
Dimension D 15 5/8 (400) 15 5/8 (400) 16 3/8 (420) 18 (460) 19 1/2 (500) 22 1/2 (570)
Dimension E 9 (230) 9 (230) 9 3/4 (250) 10 1/2 (270) 12 (310) 14 (360)
Dimension F 1 3/4 (45) 1 3/4 (45) 1 3/4 (45) 1 3/4 (45) 1 3/4 (45) 2 3/16 (55)
Dimension G 1 NPT 1 NPT 1 NPT 1 1/2 NPT 1 1/2 NPT 2 NPT
Dimension H 2 NPT 2 1/2 NPT 3* 4* 6* 8*

Manual foam
balancing valve

G
F C

E H
H

B
A
*Between flange proportioner is standard. Upon request, proportioners can also be supplied in flanged style. 001173
Note: In-line balanced pressure proportioners require a minimum of 5 pipe diameters of straight, unobstructed water inlet supply pipe.
Ordering Information
Part No. Approximate Foam Solution
Water
Part No. Standard Shipping Weight Sensing Line
Discharge
Unpainted Red Paint Description lb (kg)
Spool Valve Proportioner
702500 702506 Model CIBP-2 In-line 45 (20.4)
Proportioner Assembly Foam Concentrate
702501 702507 Model CIBP-2 1/2 In-line 45 (20.4) Sensing Line
Drain Water Inlet
Proportioner Assembly Cock
Foam sensing line
702502 702508 Model CIBP-3 In-line 50 (22.7) Valve
Proportioner Assembly Foam Drain Cock Valve
702503 702509 Model CIBP-4 In-line 65 (29.5) Concentrate
Valve
Proportioner Assembly
SPOOLVALVE
702504 702510 Model CIBP-6 In-line 80 (36.3) Pressure
Duplex Gauge Longitudinal
Proportioner Assembly Gauge Axis in horizontal
position
702505 702511 Model CIBP-8 In-line 135 (61.2) Valve Nameplate
Proportioner Assembly Check Valve
Foam Concentrate Inlet
702512 702518 Model CIBP-2M In-line 60 (27.2) 001174
Proportioner Assembly
702513 702519 Model CIBP-2 1/2M In-line 60 (27.2)
Note:Spool valve must be installed with the longitudinal axis in the horizontal
Proportioner Assembly (level) position.
702514 702520 Model CIBP-3M In-line 65 (29.5)
Proportioner Assembly Safety Data Sheet (SDS) available at www.chemguard.com
702515 702521 Model CIBP-4M In-line 90 (40.8) Note: The converted metric values in this document are provided for dimen-
Proportioner Assembly sional reference only and do not reflect an actual measurement.
702516 702522 Model CIBP-6M In-line 105 (47.6) 1TEFLON is a trademark of its respective owner.
Proportioner Assembly CHEMGUARD and the product names listed in this material are marks and/
702517 702523 Model CIBP-8M In-line 170 (77.1) or registered marks. Unauthorized use is strictly prohibited.
Proportioner Assembly

Typical In-Line Balanced Pressure Proportioning System

Foam Solution
Discharge
Foam Concentrate Storage
Tank (Atmospheric Type) Pressure/Vacuum
Vent Valve

Spool Valve

In-Line
Foam Balanced
Return Line Pressure
Pressure
Control Valve Proportioner

Water
Supply

Automatic
Concentrate
Control Valve
Foam Suction
Line

Compound
Pressure
Gauge
Foam Pump and
Driver Assembly Foam Concentrate
001175
Supply
NOTE: Flush connections are only required with protein based foam concentrates.

LEGEND:

SHUT-OFF VALVE PRESSURE GAUGE PROPORTIONER SPOOL VALVE

CHECK VALVE DUPLEX PRESSURE GAUGE FLUSH CONNECTION DIRECTION OF FLOW

PRESSURE RELIEF VALVE COMPOUND PRESSURE GAUGE STRAINER

Friction Loss Curves (Through Proportioner)
(bar) psi
(2.8) 40

(2.1) 30

(1.7) 25

(1.4) 20

(1.0) 15

( 0.69) 10
(0.62) 9
(0.55) 8
Pressure Loss

(0.48) 7

(0.41) 6

(0.34) 5

(0.28) 4

(0.21) 3

(0.17) 2.5

(0.14) 2

(0.10) 1.5

(0.07) 1
50 100 200 300 500 700 1000 2000 3000 5000 8000 gpm
(189) (379) (757) (1136) (1893) (2650) (3785) (7571) (11356) (18927) (30283) (Lpm)
FLOW RATE 001176

Minimum Inlet Pressure Versus Water Flow

(bar) psi

(13.8) 200

(10.3) 150

(6.9) 100
Water Inlet Pressure

(3.4) 50

(2.8) 40

(2.1) 30

(1.4) 20
100 200 300 500 700 1000 2000 3000 5000 gpm
(379) (757) (1136) (1893) (2650) (3785) (7571) (11356) (18927) (Lpm)
WATER FLOW 001177