Jiang2014 PDF

Download as pdf or txt
Download as pdf or txt
You are on page 1of 13

Available online at www.sciencedirect.

com

ScienceDirect
Solar Energy 103 (2014) 425437
www.elsevier.com/locate/solener

Thermochemical CO2 splitting reaction with supported


LaxA1xFeyB1yO3 (A = Sr, Ce, B = Co, Mn; 0 6 x, y 6 1)
perovskite oxides
Qingqing Jiang a,b, Jinhui Tong a,b, Guilin Zhou a,b, Zongxuan Jiang a, Zhen Li a,b, Can Li a,
a
State Key Laboratory of Catalysis, Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Dalian National Laboratory for Clean Energy,
Dalian 116023, China
b
Graduate University of Chinese Academy of Sciences, Beijing 100049, China

Received 13 December 2013; received in revised form 19 February 2014; accepted 21 February 2014
Available online 15 March 2014

Communicated by: Associate Editor Michael Epstein

Abstract

An ecient redox material for two-step thermochemical CO2 splitting reaction requires high chemical yield at relatively low reduction
temperature. Herein, the oxides with perovskite structure of formula LaxA1xFeyB1yO3 (A = Sr, Ce, B = Co, Mn; 0 6 x, y 6 1) start to
release O2 at 800 C and the largest O2 production is 11.8 ml/gperovskite at 1300 C. However, for these unsupported LaxA1xFeyB1yO3
materials, the CO production is low in spite of high reduction yield. ZrO2, Al2O3 and SiO2 are thus considered as supports to disperse
LaxA1xFeyB1yO3 materials and dierent supports induce great dierences in the reaction activity. By A-site or B-site substitution of
LaFeO3, the O2 releasing temperature has fallen from 1230 C to 800-950 C and the CO production is enhanced 23 times. LaFe0.7Co0.3-
O3 (25 wt%)/SiO2 shows the highest reaction activity among these investigated materials with the O2 production of 4.0 ml/gmaterial
(16.0 ml/gperovskite) and CO production of 7.6 ml/gmaterial (30.4 ml/gperovskite) when it is reduced at 1300 C and re-oxidized at 1100 C,
and the activity is relatively stable even after 10 cycles of the reaction. By contrast, the CO production is 4.5 ml/g for CeO2 when it
is reduced at 1400 C. The estimated activation energy for the reduction step of LaFe0.7Co0.3O3 (25 wt%)/SiO2 is around 89149 KJ/
mol according to dierent models. The CO generation step of LaFe0.7Co0.3O3 (25 wt%)/SiO2 is mainly controlled by bulk diusion
(D1) at 1000 C and then it turns to rst order surface reaction (F1) at 1100 C.
2014 Elsevier Ltd. All rights reserved.

Keywords: Solar energy; CO2 reduction; Perovskite oxide; Kinetics

1. Introduction an attractive option for solar energy utilization (Chueh


et al., 2010; Steinfeld, 2005; Furler et al., 2012; Muhich
Ecient utilization of solar energy is an important sub- et al., 2013; Jiang et al., 2014). The two-step thermochem-
ject. The conversion of concentrated solar energy into ical splitting reaction with metal oxide as redox material
chemical fuels via two-step thermochemical H2O and CO2 can be represented as follows:
splitting reaction which uses the entire solar spectrum is
MOox solar thermal energy MOred O2 1:1
Corresponding author. Tel.: +86 411 84379070; fax: +86 411 MOred H2 O=CO2 MOox H2 =CO 1:2
84694447.
E-mail address: canli@dicp.ac.cn (C. Li). Total reaction:

http://dx.doi.org/10.1016/j.solener.2014.02.033
0038-092X/ 2014 Elsevier Ltd. All rights reserved.
426 Q. Jiang et al. / Solar Energy 103 (2014) 425437

H2 O=CO2 solar energy H2 =CO O2 1:3 La1xSrxMO3 (M = Mn, Fe) have been investigated for
Various metal oxides have been investigated in the two the two-step thermochemical steam reforming of methane
step thermochemical splitting reaction, among which (Evdou et al., 2008a,b). It is desired to investigate the
Fe3O4, ZnO and CeO2 are the most popular redox materi- two step thermochemical H2O and CO2 splitting reaction
als. In order to obtain high chemical yield at relatively low with perovskite oxides because it is a more attractive way
reduction temperature, the addition of dopants into Fe3O4 for energy utilization from a long term perspective. The
and CeO2 were extensively studied with a certain degree of latest results from McDaniel et al. (2013) showed that
success (Gal et al., 2011; Gal and Abanades, 2012; Meng Sr- and Mn-doped LaAlO3d exhibited excellent reaction
et al., 2011; Schee and Steinfeld, 2012; Fresno et al., performance in two step thermochemical CO2 and H2O
2009; Kodama et al., 2008). However, the reduction to splitting reaction. The H2 yields were 9  greater, and the
nonstoichiometric MOred below 1400 C shows limited CO yields 6  greater, than those produced by ceria, when
chemical yield for most of these investigated redox oxides. it was reduced at 1350 C and re-oxidized at 1000 C.
The perovskite oxides, ABO3, have been applied in the In the present work, the perovskite oxides of formula
elds of catalysis, solid oxide fuel cells, and oxygen perme- LaxA1xFeyB1yO3 (A = Sr, Ce, B = Co, Mn; 0 6 x,
able membranes due to their unique structural features y 6 1) based on Fe3+/Fe2+ cycle were utilized in two-step
(Merino et al., 2006; Wang et al., 2004; Yang et al., 2003; thermochemical CO2 splitting reaction. It is found that
He et al., 2011; Lu et al., 2012). Their basic structural unsupported LaxA1xFeyB1yO3 materials present negligi-
framework keeps unchanged with wide variety of constitu- ble CO production in spite of high reduction yield. What
ent elements and composition, therefore the valence of cat- seems surprising is that mixing SiO2 with the perovskite
ions and the oxygen vacancy concentration can be changed oxides apparent enhances the redox activity. These
widely (Tanaka and Misono, 2001). Furthermore, the ther- A- and B-site substituted LaFeO3 show an enhanced reduc-
mal stability of perovskite oxides is better than their corre- ibility at low temperature and in some cases, the CO gener-
sponding transition metal oxides. ation activity is also largely increased. The CO production

Fig. 1. (a) The O2 evolution rate-time proles from 800 C to 1300 C and (b) the CO generation rate-time proles at 1000 C of LaFexB1xO3 (B = Mn
and Co; x = 1.0, 0.7 and 0).
Q. Jiang et al. / Solar Energy 103 (2014) 425437 427

for LaFe0.7Co0.3O3 (25 wt%)/SiO2 is 7.6 ml/gmaterial skite oxides were well-mixed with supports in which the
(30.4 ml/gperovskite) when it is reduced at 1300 C and re- weight ratio was 1:3. The perovskite oxides and commer-
oxidized at 1100 C. By contrast, the CO production is cial supports were mechanically mixed in a mortar for half
4.5 ml/g for CeO2 when it is reduced at 1400 C. Cycle per- an hour. After that, the mixture was heated at 900 C in a
formance shows that the redox activity is stable even after mue burner for 10 h.
10 cycles of high temperature reaction. The calculated acti-
vation energies of the reduction step and the main limita- 2.2. Characterization of samples
tion of the CO generation reaction was given by kinetic
analysis. The synthesized samples were characterized by X-ray
powder diraction (XRD) on a Rigaku D/Max-2500/PC
2. Experimental section powder diractometer. Each sample powder was scanned
using Cu Ka radiation with an operating voltage of
2.1. Synthesis method 40 kV and an operating current of 200 mA. The scan rate
of 5 min1 was applied to record the XRD patterns in
The citrate method was employed to produce nanopar- the range of 2080 at a step size of 0.02. The specic sur-
ticles of these LaxA1xFeyB1yO3 (A = Sr, Ce; B = Mn, face areas of the samples were taken with a Micromeritics
Co, Ni) perovskite oxides (Merino et al., 2006). Aqueous ASAP 2000 adsorption analyzer.
solutions of starting nitrates were mixed with an aqueous
solution of citric acid. The molar ratio between the total 2.3. Reaction activity testing
amount of nitrates and citric acid was 1:2. The resulting
solution was evaporated at 80 C and then completely The two-step thermochemical splitting reaction was car-
dried overnight at 120 C. The spongy material thus ried out at a laboratory scale in a xed bed conguration.
obtained was crushed and calcined at 700 C for 4 h. The The vertical alumina tubular reactor was placed inside an
perovskite oxides were supported on commercial supports electric furnace. The argon ow (purity 99.9996%) rstly
(SiO2, ZrO2 and Al2O3) before reaction testing. The perov- passed through a deoxidation tube to get rid of the residual

Fig. 2. SEM images of (a) LaFeO3, (b) LaFeO3 after high temperature treatment and (c) LaFe0.7Co0.3O3 (25 wt%)/SiO2 after 10 cycles.
428 Q. Jiang et al. / Solar Energy 103 (2014) 425437

O2 before it passed into the reactor. The O2 concentration CO gas product was analyzed by a gas chromatograph
in the experimental system was about 20 ppm. (Aligent 6890) equipped with a GDX-01 column and a
The reduction reaction was performed with an argon FID detector, which took gas sample at the reactor outlet
ow rate of 100 ml/min. For unsupported LaxA1xFeyB1yO3 every ca. 1 or 2 min. Numerical integration of the molar
(A = Sr, Ce; B = Mn, Co) samples, 0.5 g of the materials ow rate-time curves gave the production of O2 and CO.
were heated to 800 C with a 20 C/min heating rate and In this study, the results were expressed in terms of O2
then to 1300 C with a 10 C/min heating rate. To investi- and CO production (ml) per gram of active perovskite oxi-
gate the eect of dierent supports on the reaction activity, des (ml/gperovskite) and per gram of total mixed materials
0.4 g of the mixed materials were heated to 800 C with a (ml/gmaterial).
20 C/min heating rate and then to 1300 C with a
10 C/min heating rate. To investigate the eect of A-site 3. Results and discussion
or B-site substitution on the reaction activity, 0.4 g of the
mixed materials were heated to 1200 C with a 20 C/min 3.1. LaFexB1xO3 as redox materials
heating rate and then to 1300 C with a 5 C/min heating
rate. The temperature plateau at 1300 C was maintained LaFexB1xO3 (B = Mn and Co; x = 1.0, 0.7 and 0) were
for a while until O2 releasing reaction completed. The pro- heated from 800 C to 1300 C with a heating rate of
duced gas mixture was analyzed with a gas chromatograph 10 C/min under an argon (purity 99.9996%) ow of
(Aligent 6890) equipped with a 5A molecular sieve column 100 ml/min. As shown in Fig. 1(a), LaFeO3 starts to release
and a TCD detector, which took gas sample at the reactor O2 at 1210 C and the nal amount of oxygen released is
outlet every ca. 2 min. 1.3 ml/gperovskite. By contrast, LaMnO3 and LaCoO3
The reduced state of the oxide was maintained under the start to release O2 at 800 C and the O2 production is
protection of Ar with a ow rate of 500 ml/min before CO2 10.6 ml/gperovskite and 11.8 ml/gperovskite, respectively. The
was exposed to the reactor. After the electric furnace was results agree well with the thermodynamic analysis which
fell to the certain temperature (9001100 C), and then indicates that the reduction of Mn3O4 to MnO and of
CO2 (purity 99.999%) with a ow rate of 500 ml/min was Co3O4 to CoO is much easier than that of Fe3O4 to FeO
injected to react with the oxygen-decient materials. The (Kodama and Gokon, 2007). As a result, doping Mn and

Fig. 3. (a) The O2 evolution rate-time proles from 800 C to 1300 C and (b) the CO generation rate-time proles at 1000 C of LaFe0.7Co0.3O3 dispersed
on dierent supports for the rst cycle.
Q. Jiang et al. / Solar Energy 103 (2014) 425437 429

Fig. 4. XRD patterns of (a) LaFe0.7Co0.3O3, Al2O3 and LaFe0.7Co0.3O3 (25 wt%)/Al2O3 after reaction, (b) LaFe0.7Co0.3O3, ZrO2 and LaFe0.7Co0.3O3
(25 wt%)/ZrO2 after reaction, and (c) LaFe0.7Co0.3O3 (25 wt%)/SiO2 after 10 cycles of CO2 splitting reaction.

Fig. 5. The CO generation activity of (a) LaAl11xFexO19 (b) CoxFe3xO4 at 1000 C. The value of x is according to the content of iron in LaFe0.7Co0.3O3
(25 wt%)/Al2O3 and LaFe0.7Co0.3O3 (25 wt%)/ZrO2.

Co into LaFeO3 makes the thermal reduction step thermo- present low CO generation rate and negligible CO produc-
dynamically more favorable in comparison to pure LaFeO3. tion at 1000 C in spite of high reduction yield. SEM
The corresponding O2 production is increased from images show that the samples are aggregated into large
1.3 ml/gperovskite up to 8.5 ml/gperovskite for LaFe0.7Mn0.3O3 particles after high temperature treatment and the poor
and 6.4 ml/gperovskite for LaFe0.7Co0.3O3, respectively. CO generation activity may be due to sintering (Fig. 2(a
The generation of CO for these reduced LaFexB1xO3 and b)). Therefore, the perovskite oxides are dispersed
materials shown in Fig. 1(b) demonstrates that CO2 split- on supports to enhance the high temperature thermal
ting reaction activity is poor at 1000 C. These samples stability.
430 Q. Jiang et al. / Solar Energy 103 (2014) 425437

Fig. 6. XRD patterns of (a) SrFeO3, La0.7Sr0.3FeO3, La0.7Ce0.3FeO3 and LaFeO3 and (b) LaMnO3, LaCoO3, LaFe0.7Co0.3O3, LaFe0.7Mn0.3O3 and
LaFeO3.

Table 1 3.2. The eect of dierent supports on the reaction activity


BET surface areas and crystallite sizes of these perovskite oxides.
Samples Crystallite size Surface area ZrO2, Al2O3 and SiO2 were thus used as the supports.
(A) (m2 g1) The loading of LaFe0.7Co0.3O3 was set to 25% on a weight
LaFeO3 233 10.7 basis. These supported materials were reduced at tempera-
La0.7Sr0.3FeO3 316 9.7 ture up to 1300 C (with a heating rate 10 C/min) under an
La0.7Ce0.3FeO3 465 9.6 argon ow of 100 ml/min.
LaFe0.7Co0.3O3 249 9.2
LaFe0.7Mn0.3O3 207 18.5
Indeed, The O2 evolution activity is largely enhanced by
SiO2 2.9 dispersing LaFe0.7Co0.3O3 on supports of ZrO2, Al2O3 and
LaFe0.7Co0.3O3/SiO2 after10 cycles 0.6 SiO2, as shown in Fig. 3(a). Dierent supports (ZrO2,
The crystallite size is calculated Al2O3 and SiO2) induce great dierences in the O2 pro-
from XRD duce activity. The maximum O2 evolution rate for

Fig. 7. (a) The O2 evolution rate-time proles, (b) CO generation rate-time proles at 1100 Cof LaxA1xFeO3 (A = Sr and Ce) (25 wt%)/SiO2 for the rst
cycle.
Q. Jiang et al. / Solar Energy 103 (2014) 425437 431

LaFe0.7Co0.3O3 (25 wt%)/SiO2 is 13  greater, for LaFe0.7- lar to that of CoxFe3xO4 (Fig. 5(b)) which proves the
Co0.3O3 (25 wt%)/Al2O3 is 5.6  greater, and for LaFe0.7- active species is CoxFe3xO4. For LaFe0.7Co0.3O3
Co0.3O3 (25 wt%)/ZrO2 is 2.9  greater, than that (25 wt%)/SiO2, silica is transformed to stable tridymite
produced by unsupported LaFe0.7Co0.3O3. LaFe0.7Co0.3O3 phase after high temperature treatment. The high tempera-
(25 wt%)/SiO2 is considered to be the best candidate which ture stable tridymite phase is the main factor for high reac-
could be reduced to a greater extent at same reduction tem- tion activity. High temperature solid state reaction occurs
perature. The O2 evolution curves are quite dierent from between silica and perovskite oxides after high temperature
each other mainly due to dierent high temperature solid treatment. The redox active agents are not perovskite phase
state reactions occur between LaFe0.7Co0.3O3 and but the mixed materials, including La2SiO5, FexSiyOz,
supports. tridymite and others. The active redox element is Fe3+,
As shown in Fig. 3(b), the CO generation activity however, the reaction activity of LaxA1xFeyB1yO3/SiO2
follows the order of intensities LaFe0.7Co0.3O3 (25 wt%)/ is quite dierent from their corresponding ferrites. The
SiO2 > LaFe0.7Co0.3O3 (25 wt%)/ZrO2 > LaFe0.7Co0.3O3 mixed structure may be the other reason for the enhanced
(25 wt%)/Al2O3 > LaFe0.7Co0.3O3. The dierent productiv- reaction activity.
ities of LaFe0.7Co0.3O3 dispersed on dierent supports are
thus attributed to the dierent structural changes after high 3.3. The eect of A-site substitution of LaFeO3 on the
temperature treatment. reaction activity
The XRD patterns shown in Fig. 4(a) indicates that Fe-
substituted hexaaluminate (LaAl11xFexO19) is formed for Ce4+- and Sr2+-substituted LaFeO3 were synthesized
LaFe0.7Co0.3O3 (25 wt%)/Al2O3 after high temperature and tested in the two step thermochemical CO2 and H2O
treatment. The CO production of LaAl11xFexO19 is negli- splitting reaction. XRD patterns of SrFeO3, La0.7Sr0.3FeO3,
gible (Fig. 5(a)) and thus Al2O3 supported LaFe0.7Co0.3O3 La0.7Ce0.3FeO3 and LaFeO3 are exhibited in Fig. 6(a). For
exhibits low CO generation activity. For LaFe0.7Co0.3O3 La0.7Sr0.3FeO3, the pure orthorhombic perovskite-type
(25 wt%)/ZrO2 after high temperature treatment, phases structure is formed, and single component oxide such as
of La2Zr2O7, CoxFe3xO4, and ZrO2 are observed. The La2O3, and Fe2O3, has not been detected, indicating that
reaction activity of LaFe0.7Co0.3O3 (25 wt%)/ZrO2 is simi- the perovskite-type structure is preserved with the partial

Fig. 8. (a) The O2 evolution rate-time proles and (b) the CO generation rate-time proles at 1100 C of LaFexCo1xO3 (x = 1, 0.9, 0.7, 0.5) (25 wt%)/
SiO2 for the rst cycle.
432 Q. Jiang et al. / Solar Energy 103 (2014) 425437

substitution of A-site elements. For La0.7Ce0.3FeO3, tiny rate is increased 2 times after the introduction of Ce4+ into
CeO2 phase is observed. The crystallite sizes were estimated LaFeO3. The O2 production for these SiO2 supported
to be <50 nm using Scherrers equation, as represented in LaxA1xFeyB1yO3 samples is shown in Fig. 10(a) and it
Table 1. The samples synthesized by citrate method exhibit indicates that the O2 production is enhanced 23 times by
low specic surface area, about 10 m2 g1. A-site substitution.
From Fig. 7(a) it can be seen that the O2 releasing tem- However, the high reduction yield of La0.7Sr0.3FeO3
perature has fallen from 1230 C to 970 C by partial sub- (25 wt%)/SiO2 does not result in high CO generation rate
stitution of La3+ with Sr2+ and the maximum O2 evolution (Fig. 7b). The CO generation rate of La0.7Sr0.3FeO3

Fig. 9. The (a) O2 evolution rate-time proles and (b) CO generation rate-time proles at 1100 C of LaFexB1xO3 (B = Mn and Co) (25 wt%)/SiO2 for
the rst cycle.

Fig. 10. (a) O2 and (b) CO production of LaxA1xFeyB1yO3 (A = Sr, Ce; B = Co, Mn) (25 wt%)/SiO2 for the rst cycle.
Q. Jiang et al. / Solar Energy 103 (2014) 425437 433

(25 wt%)/SiO2 is only half of LaFeO3 (25 wt%)/SiO2. The


CO production during the rst 20 min of La0.7Sr0.3FeO3
(25 wt%)/SiO2 is also half of LaFeO3 (25 wt%)/SiO2.
Nevertheless, the total CO production is increased from
2.0 ml/gmaterial (8.1 ml/gperovskite) to 2.8 ml/gmaterial
(11.2 ml/gperovskite) by substituted La3+ with Sr2+.
For La0.7Ce0.3FeO3 (25 wt%)/SiO2, although the CO
generation rate does not show much improvement, the
enhanced reducibility leads to higher CO and H2 produc-
tion as compared to LaFeO3 (25 wt%)/SiO2. The total
CO production is increased from 2.0 ml/gmaterial
(8.1 ml/gperovskite) to 3.1 ml/gmaterial (12.4 ml/gperovskite) by
substituted La3+ with Ce4+.
The defect chemistry of LaxA1xFeO3 has been widely
investigated. The partial substitution of Sr2+ for La3+ leads
to higher oxidation states of Fe ion and the simultaneous
Fig. 12. Cycle performance of LaFe0.7Co0.3O3 (25 wt%)/SiO2 for 10 times
formation of structural defects (Evdou et al., 2008a,b; Ferri
with reduction temperature at 1300 C and CO generation reaction at
and Forni, 1998; Royer et al., 2005). The enhanced reduc- 1100 C.
ibility could be attributed to the modied reducibility of Fe
ion. However, the vacancies for compensating the Sr2+
doping acceptors are considered stable and could not the O2 evolution activity increases as the Co content
utilize during the CO2 and H2O splitting reaction. There- increasing. The CO generation rate reaches the maximum
fore, the high reduction yield and low fuel productivity when x is 0.3 as the x value varies from 0 to 0.5
for La0.7Sr0.3FeO3 (25 wt%)/SiO2 is reasonable. According (Fig. 8(b)). The initial CO generation rate of LaFe0.7Co0.3O3
to the previous TPR results, the addition of Ce4+ into the (25 wt%)/SiO2 is 4 times faster than that of LaFeO3
perovskite lattice could enhance the reducibility of Fe3+ (25 wt%)/SiO2 and the CO production for the rst 20 min
species due to the interaction between Fe3+Fe2+ and is increased from 1.2 ml/gmaterial (4.6 ml/gperovskite) up to
Ce4+Ce3+ redox couples (Royer et al., 2005). Therefore, 4.3 ml/gmaterial (17.2 ml/gperovskite). The total CO production
the addition of Ce4+ into LaFeO3 favours the reduction for LaFexCo1xO3 (x = 0.7 and 0.5) (25 wt%)/SiO2 is almost
process and the corresponding CO production. three times larger than that of LaFeO3 (25 wt%)/SiO2
(Fig. 10(b)). The substitution of Fe3+ with Co3+ favors the
3.4. The eect of B-site substitution of LaFeO3 on the reduction of Fe3+ to Fe2+, therefore, the reaction activity
reaction activity enhances with the molar ratio of Co to Fe increasing, how-
ever, Fe3+/Fe2+ is the eective redox pair, if too much
Combination of two dierent ions at the B-site brings Fe3+ is substituted, the CO generation activity could be
about synergistic eects and is a powerful tool for enhance- decreased.
ment of the reducibility. Co- and Mn- are thus considered LaFe0.7Mn0.3O3 (25 wt%)/SiO2 exhibits the highest O2
for the substitution of Fe in LaFeO3. The studied materials evolution activity among these A-site and B-site substituted
are LaFe1xCoxO3 (x = 0.9, 0.7, 0.5) and LaFe0.7Mn0.3O3. LaFeO3 (Fig. 9(a)). The maximum O2 evolution rate is
The XRD patterns are presented in Fig. 6(b) conrming 0.37 ml min1 g1 material for LaFe0.7Mn0.3O3 (25 wt%)/SiO2,
the formation of perovskite-type structure. by contrast, 0.13 ml min1 g1 material for LaFe0.7Co0.3O3
The O2 evolution activity for LaFexCo1xO3 as a func- (25 wt%)/SiO2, 0.13 ml min1 g1 material for La0.7Ce0.3FeO3
tion of Co content is shown in Fig. 8(a). It can be seen that (25 wt%)/SiO2 and 0.1 ml min1 g1 material for LaFeO3

Fig. 11. (a) The O2 rate-time proles at 1200 C, 1300 C, and 1400 C, (b) the corresponding CO generation activity at 1100 C of LaFe0.7Co0.3O3/SiO2.
434 Q. Jiang et al. / Solar Energy 103 (2014) 425437

(25 wt%)/SiO2. The initial CO generation rate of LaFe0.7- that O2 production below 1200 C is not due to the reduction
Mn0.3O3 (25 wt%)/SiO2 is similar to that of LaFeO3 of Fe3+ to Fe2+, but the reduction of Co3+ to Co2+. The cor-
(25 wt%)/SiO2, and it is much lower than that of responding CO generation activity of that reduced at 1400 C
LaFe0.7Co0.3O3 (25 wt%)/SiO2 (Fig. 9(b)), nevertheless, the is much lower than that reduced at 1300 C which proves that
CO productivity is comparable to that of LaFe0.7Co0.3O3 the reaction performance of LaFe0.7Co0.3O3 (25 wt%)/SiO2 is
(25 wt%)/SiO2, as shown in Fig. 10(b). dierent from ferrites.
Fig. 11 exhibits the CO2 splitting activity for LaFe0.7- Cycle performance for LaFe0.7Co0.3O3 (25 wt%)/SiO2
Co0.3O3 (25 wt%)/SiO2 as the reduction temperature varies was performed with the reduction temperature at 1300 C
from 1200 C to 1400 C. The O2 production is largely and CO generation step at 1100 C. As shown in Fig. 12,
increased as reduction temperature increases from the O2 and CO production for LaFe0.7Co0.3O3
1200 C to 1400 C, from 1.6 ml/gmaterial up to 6.3 ml/gmaterial. (25 wt%)/SiO2 becomes even higher as the increasing of cycle
The corresponding CO production is only 0.4 ml/gmaterial number. The ratio of CO production to O2 production is
when the reduction temperature is 1200 C which indicates more and more close to 2 as the increasing of cycle number.

Fig. 13. (a) O2 evolution rate of LaFe0.7Co0.3O3 (25 wt%)/SiO2 under heating rate of 10 C/min, (be) Arrhenius plot for the non-isothermal reduction of
LaFe0.7Co0.3O3 (25 wt%)/SiO2 according to dierent models. F1 means rst order reaction; F2 means second order reaction; R2 and R3 means
geometrical-contracting models.
Q. Jiang et al. / Solar Energy 103 (2014) 425437 435

The CO production is 7.6 ml/gmaterial (30.4 ml/gperovskite) for And a is dened as:
the 10th cycle, by contrast, the CO production is 4.5 ml/g for
CeO2 when it is reduced at 1400 C. It indicates that SiO2 Total O2 t
a 3:3
supported LaxA1xFeyB1yO3 (A = Sr, Ce; B = Co, Mn) Total O2
pervoskite oxides are promising redox materials for fuel pro-
duction via two-step solar thermal splitting reaction at rela- h i
da=dT b
tively low reduction temperature. The curve of ln f a
versus 1/T should be linear if the
hypothetical model is reasonable, and then activation
3.5. Kinetic analysis energy Ea can be calculated from slope of the line.
The O2 evolution rate-time proles of LaFe0.7Co0.3O3
The kinetic studies for the O2 evolution reaction were (25 wt%)/SiO2 from 800 C to 1300 C with a heating rate
performed under non-isothermal experimental condition of 10 C/min is shown in Fig. 13(a). The reaction order (F1
with a constant heating rate of 10 C/min. According to and F2) and geometrical-contracting (R2 and R3) models
the literatures, the model can be expressed as follows have been attempted for f (a). The experimental data are
(Levenspiel, 1972; Galwey and Brown, 1999; Francis processed according to (3.1). The linear regression for the
et al. (2010); Schunk and Steinfeld, (2009) experimental data is shown in Fig. 13(be). Both surface
  reaction order (F1 and F2) and geometrical-contracting
da=dT b Ea (R2 and R3) models show excellent linear t. It is dicult
ln ln A  3:1
f a RT to precisely determine the actual reaction model for the
n
reduction reaction of LaFe0.7Co0.3O3 (25 wt%)/SiO2. The
f a 1  a 3:2 estimated activation energy according to dierent models

Fig. 14. (a) the CO generation rate-time proles for LaFe0.7Co0.3O3 (25 wt%)/SiO2 from 900 C to 1100 C (b and c) normalized rate data compared to
solid state reaction model of the CO generation reaction for LaFe0.7Co0.3O3 (25 wt%)/SiO2 at 1000 C and 1100 C. F1 means rst order reaction; D1
means rst order diusion reaction model.
436 Q. Jiang et al. / Solar Energy 103 (2014) 425437

is 108 KJ/mol for F1, 149 KJ/mol for F2, 89 KJ/mol for thermal splitting reaction at relatively low reduction
R2, and 97 KJ/mol for R3, respectively. temperature.
The CO generation rate can be expressed as follows:
da Acknowledgements
kf a 3:4
dt
This work was nancially supported by National
For isothermal experiment, if the normalized rate data
Program on Key Basic Research Project (Grant
agree well with a given kinetic model, (3.4) can be
2009CB220010), National Natural Science Foundation of
expressed as (Gotor et al., 2000; Perez-Maqueda et al.,
China (Grant 21061140361), and Solar Energy Action
2002; Yang et al., 2009):
Plan of Chinese Academy of Sciences (Grant KGCX2-
da=dt f a YW-393-1).
3:5
da=dta0:5 f aa0:5
Fig. 14(a) shows the CO generation rate-time proles for References
LaFe0.7Co0.3O3 (25 wt%)/SiO2 from 900 C to 1100 C. It
Chueh, W.C., Falter, C., Abbott, M., Scipio, D., Furler, P., Haile, S.M.,
can be seen that the CO generation rate increases with the Steinfeld, A., 2010. High-ux solar-driven thermochemical dissociation
increasing of temperature. The normalized rate data for of CO2 and H2O using nonstoichiometric ceria. Science 330, 1797
LaFe0.7Co0.3O3 (25 wt%)/SiO2 compared to various solid 1800.
state reaction models are shown in Fig. 14(b and c). The Evdou, A., Nalbandian, L., Zasplis, V.T., 2008a. Perovskite membrane
CO generation reaction of LaFe0.7Co0.3O3 (25 wt%)/SiO2 reactor for continuous and isothermal redox hydrogen production
from the dissociation of water. J. Membr. Sci. 325, 704711.
agrees well with a bulk diusion model (D1) at 1000 C Evdou, A., Zaspalis, V., Nalbandian, L., 2008b. La(1x)SrxMnO3d
(0.2 < a < 0.8). When the CO generation reaction is per- perovskites as redox materials for the production of high purity
formed at 1100 C, the reaction turns to the rst order sur- hydrogen. Int. J. Hydrogen Energy 33, 55545562.
face reaction (0.1 < a < 1.0). Ferri, D., Forni, L., 1998. Methane combustion on some perovskite-like
mixed oxides. Appl. Catal. B: Environ. 16, 119126.
Francis, T.M., Lichty, P.R., Weimer, A.W., 2010. Manganese
4. Conclusions oxide dissociation kinetics for the Mn2O3 thermochemical
water-splitting cycle. Part 1: Experimental. Chem. Eng. Sci.
The oxides with perovskite structure of formula 65, 37093717.
Fresno, F., Fernandez-Saavedra, R., Gomez-Mancebo, M.B., Vidal, A.,
LaxA1xFeyB1yO3 (A = Sr, Ce; B = Co, Mn) were uti-
Miguel Sanchez, V., Rucandio, M.I., Quejido, J.A., Romero, M., 2009.
lized in two-step thermochemical CO2 splitting reaction. Solar hydrogen production by two-step thermochemical cycles: eval-
For unsupported pervoskite oxides, the CO generation uation of the activity of commercial ferrites. Int. J. Hydrogen Energy
activity was negligible in spite of promising O2 evolution 34, 29182924.
production at low reduction temperature. Thus, commer- Furler, P., Furler, P., Schee, J.R., Steinfeld, A., 2012. Syngas
production by simultaneous splitting of H2O and CO2 via ceria
cial ZrO2, Al2O3 and SiO2 were thus considered as the
redox reactions in a high-temperature solar reactor. Energy
supports. Dierent supports have great inuence on the Environ. Sci. 5, 60986103.
reaction activity and SiO2 was found to be the best candi- Gal, A.L., Abanades, S., 2012. Dopant incorporation in ceria for
date among these investigated supports. By A-site or B-site enhanced water-splitting activity during solar thermochemical hydro-
substitution of LaFeO3, the O2 evolution temperature was gen generation. J. Phys. Chem. C 116, 1351613523.
Gal, A.L., Abanades, S., Flament, G., 2011. CO2 and H2O splitting for
reduced by 200400 C and the fuel production was
thermochemical production of solar fuels using nonstoichiometric
enhanced 23 times. LaFe0.7Co0.3O3 (25 wt%)/SiO2 exhib- ceria and ceria/zirconia solid solutions. Energy Fuels 25, 4836.
ited the highest reaction activity among these investigated Galwey, A.K., Brown, M.E., 1999. Thermal Decomposition of Ionic
perovskite oxides. The maximum CO generation rate for Solids, rst ed. Elsevier, New York.
LaFe0.7Co0.3O3 (25 wt%)/SiO2 was 4 times greater than Gotor, F.J., Criado, J.M., Malek, J., Koga, N., 2000. Kinetic analysis of
solid-state reactions: the universality of master plots for analyzing
that produced by LaFeO3 (25 wt%)/SiO2. The CO produc-
isothermal and nonisothermal experiments. J. Phys. Chem. A 104,
tion for LaFe0.7Co0.3O3 (25 wt%)/SiO2 was 7.6 ml/gmaterial 1077710782.
(30.4 ml/gperovskite) when the sample was reduced at He, Y.F., Zhu, X.F., Yang, W.S., 2011. The role of a-site ion nonsto-
1300 C, by contrast, the CO production was 4.5 ml/g for ichiometry in the oxygen absorption properties of Sr1+xCo0.8Fe0.2O3
CeO2 when it was reduced at 1400 C. The estimated acti- oxides. AIChE J. 57, 8795.
Jiang, Q.Q., Zhou, G.L., Jiang, Z.X., Li, C., 2014. Thermochemical CO2
vation energy for the reduction step of LaFe0.7Co0.3O3
splitting reaction with CexM1xO2d (M = Ti4+, Sn4+, Hf4+, Zr4+,
(25 wt%)/SiO2 was around 89149 KJ/mol according to La3+, Y3+ and Sm3+) solid solutions. Solar Energy 99, 5566.
dierent models. The kinetic analysis of the CO generation Kodama, Tatsuya, Gokon, Nobuyuki, 2007. Thermochemical cycles for
step of LaFe0.7Co0.3O3 (25 wt%)/SiO2 indicated that the high-temperature solar hydrogen production. Chem. Rev. 107, 4048
reaction was mainly controlled by bulk diusion (D1) at 4077.
Kodama, T., Gokon, N., Yamamoto, R., 2008. Thermochemical two-step
1000 C and then it turned to rst order surface reaction
water splitting by ZrO2-supported NixFe3xO4 for solar hydrogen
(F1) at 1100 C. Overall, SiO2 supported LaxA1xFeyB1yO3 production. Solar Energy 82, 7379.
(A = Sr, Ce; B = Co, Mn) pervoskite oxides are promising Levenspiel, O., 1972. Chemical Reaction Engineering. John Wiley & Sons,
redox materials for fuel production via two-step solar New York.
Q. Jiang et al. / Solar Energy 103 (2014) 425437 437

Lu, H., Zhu, L.L., Kim, J.P., Son, S.H., Park, J.H., 2012. Perovskite Royer, S., Alamdari, H., Duprez, D., Kaliaguine, S., 2005. Oxygen storage
La0.6Sr0.4B0.2Fe0.8O3-d (B = Ti, Cr, Co) oxides: structural, reduction capacity of La1xAxBO3 perovskites (with A = Sr, Ce; B = Co, Mn)
tolerant, sintering, and electrical properties. Solid State Ionics 209 relation with catalytic activity in the CH4 oxidation reaction. Appl.
210, 2429. Catal. B: Environ. 58, 273288.
McDaniel, A.H., Miller, E.C., Arin, D., Ambrosini, A., Coker, E.N., Schee, J.R., Steinfeld, A., 2012. Thermodynamic analysis of cerium-
OHayre, R., Chueh, W.C., Tong, J.H., 2013. Sr- and Mn-doped based oxides for solar thermochemical fuel production. Energy Fuels
LaAlO3dfor solar thermochemical H2 and CO production. Energy 26, 19281936.
Environ. Sci. 6, 24242428. Schunk, L.O., Steinfeld, A., 2009. Kinetics of the thermal dissociation of
Meng, Q.L., Lee, C.I., Shigeta, S., Kaneko, H., Tamaura, Y., 2011. ZnO exposed to concentrated solar irradiation using a solar-driven
Reactivity of CeO2-based ceramics for solar hydrogen production via a thermogravimeter in the 18002100 K range. AIChE J. 55, 14971503.
two-step water-splitting cycle with concentrated solar energy. Int. J. Steinfeld, A., 2005. Solar thermochemical production of hydrogena
Hydrogen Energy 36, 1343513441. review. Solar Energy 78, 603615.
Merino, N.A., Barbero, B.P., Ruiz, P., Cadus, L.E., 2006. Synthesis, Tanaka, H., Misono, M., 2001. Advances in designing perovskite
characterisation, catalytic activity and structural stability of LaCo1y- catalysts. Curr. Opin. Solid State Mater. Sci. 5, 381387.
FeyO3k perovskite catalysts for combustion of ethanol and propane. Wang, C.H., Chen, C.L., Weng, H.S., 2004. Surface properties and
J. Catal. 240, 245257. catalytic performance of La1xSrxFeO3 perovskite-type oxides for
Muhich, C.L., Evanko, B.W., Weston, K.C., Lichty, P., Liang, X.H., methane combustion. Chemosphere 57, 11311138.
Martinek, J., Musgrave, C.B., Weimer, A.W., 2013. Ecient gener- Yang, Tan, Liang, Gu, X.H., Jin, W.Q., Zhang, L.X., Xu, N.P., 2003.
ation of H2 by splitting water with an isothermal redox cycle. Science New series of Sr(Co, Fe, Zr)O3-dperovskite-type membrane materials
341, 540542. for oxygen permeation. Ind. Eng. Chem. Res. 42, 22992305.
Perez-Maqueda, L.A., Criado, J.M., Gotor, F.J., Malek, J., 2002. Yang, H.C., Eun, H.C., Cho, Y.Z., Lee, H.S., Kim, I.T., 2009. Kinetic
Advantages of combined kinetic analysis of experimental data analysis of dechlorination and oxidation of PrOCl by using a non-
obtained under any heating prole. J. Phys. Chem. A 106, 28262868. isothermal TG method. Thermochim. Acta 484, 7781.

You might also like