Hanbell Maintenance Manual

HANBELL SCREW COMPRESSORS
MAINTENANCE MANUAL
HANBELL PRECISE MACHINERY CO., LTD.

TEL: (03) 483-6215
FAX: (03) 483-6223
http://www.hanbell.com.tw
HBME-RC-05-B
CONTENTS
I. HOW TO REPLACE CAPACITY SOLENOID VALVE
I-1. Dismantle Solenoid Valve 1

I-2. Assembly Solenoid Valve 2
II. HOW TO CHANGE 4-STEP TO STEPLESS CAPACITY CONTROL
II-1. Dismantle Capacity Solenoid Valve 4

II-2. Assembly Cover Plate 5
II-3. Assembly Capacity Solenoid Valve (N.C, SV1) 6
II-4. Assembly Capacity Solenoid Valve (N.O, SV2) 8
III. HOW TO CHANGE STEPLESS TO 4-STEP CAPACITY CONTROL
III-1. Dismantle Capacity Solenoid Valve (N.C, SV1) 10

III-2. Dismantle Capacity Solenoid Valve (N.O, SV2) 10
III-3. Assembly Capillary 11
III-4. Assembly 4-step Capacity Solenoid Valve 12
IV. HOW TO REPLACE OIL FILTER, OIL LEVEL SWITCH
IV-1. Dismantle Oil Filter Flange 13

IV-2. Change Oil Filter 14
IV-3. Assembly Oil Filter to Casing 15
IV-4. Dismantle Oil Level Switch Cover 16
IV-5. Assembly Oil Level Switch Cover 17
V. HOW TO REPLACE SUCTION FILTER
V-1. Dismantle Suction Flange 18

V-2. Assembly Suction Filter 19
VI. HOW TO REPLACE CHECK VALVE, OIL SEPARATOR
VI-1. Dismantle Check Valve 20

VI-2. Dismantle Oil Separator 21
VI-3. Clean Oil Separator 21
VI-4. Assembly Oil Separator to Compressor 22
VI-5. Assembly Check Valve 23
VII. HOW TO REPLACE MOTOR ASSEMBLY, MOTOR STATOR
VII-1. Dismantle Electrical Cable Plate 24

VII-2. Dismantle Motor Assembly, Motor Rotor 24
VII-3. Dismantle Motor Stator 25
VII-4. Assembly Motor Stator 27
VII-5. Assembly Motor Rotor 30
VII-6. Assembly Motor to Compressor 31
VII-7. Assembly Motor Cable Plate 33
VIII. HOW TO REPLACE PISTON, PISTON ROD, SLIDE VALVE
VIII-1. Dismantle Oil Separator 34

VIII-2. Dismantle Piston, Piston Rod 35
VIII-3. Dismantle Bearing Seat, Slide Valve 36
VIII-4. Assembly Slide Valve 37
VIII-5. Assembly Bearing Seat 39
VIII-6. Assembly Piston Rod, Piston 40
VIII-7. Assembly Discharge Cover Plate 42
IX. HOW TO REPLACE MALE & FEMALE ROTORS, BEARINGS
IX-1. Dismantle Bearing Slot Nut 44

IX-2. Dismantle Male and Female Rotor 45
IX-3. Dismantle Discharge and Suction Bearings 46
IX-4. Assembly Male and Female Rotor, Discharge Bearings 47
IX-5. Assembly Suction Bearings 55
IX-6. Assembly Oil Separator 58
X. INDEX
List of special tools 59

List of bearings 66
Motor insulation standard 67
Compressor torque settings 67
Slide valve housing clearance 67
RC compressor spare parts list (RC10 ~ RC24) 68
RC compressor explosion drawing (RC10 ~ RC24) 86
INTRODUCTION
This HANBELL semi-hermetic twin-screw compressor maintenance manual is

described regarding the maintenance procedures of HANBELL itself.
This handbook will serve as a guide or reference in order to do the maintenance or
overhauling of a compressor.
HANBELL developed its screw compressors with high precision and accuracy with
its own technology. Therefore, before starting the overhauling of compressor, we fully
recommend that proper handling and preparation of components, spare parts, tools, clean
and well-organized working conditions, and full study of this handbook are necessary.
Although proper maintenance is described in this handbook, the person with full
knowledge and understanding of such work should perform maintenance of compressor.
Otherwise, it should be an authorized technician from HANBELL or HANBELL appointed
agent.
I. HOW TO REPLACE CAPACITY SOLENOID VALVE
NOTE: If the compressor is still connected in the chiller system, make sure to pump
down first and release the pressure inside the compressor and shut down the system
to prevent any accident to happen in the job site.
I-1. DISMANTLE SOLENOID VALVE
Step 1. Loosen first the nut of the solenoid valve using

a wrench and remove the solenoid coil.
Step 2. Loosen all the screw of capacity solenoid valve

and remove the solenoid valve.
1
Step 3. Clean the surface of the compressor casing
using oilstone and clean the oil line hole using
pressurize air.
I-2. ASSEMBLY CAPACITY SOLENOID VALVE
Step 1. Put first the two O-rings to each capacity

solenoid valve (make sure to use new O-rings), and be
careful not to drop or deform the O-rings when installing
it to prevent leakage.
Step 2. Install the capacity solenoid valve to

compressor casing and make sure that the O-rings are
in the same position with the compressor casing oil line
hole.
O-ring and hole must be

in the same position
2
Step 3. Install all capacity solenoid valves to
compressor casing and put all screws and tighten it.
Step 4. Install the capacity solenoid coil on the capacity

solenoid valve.
II. HOW TO CHANGE 4-STEP TO STEP-LESS CAPACITY CONTROL
NOTE: Make sure to release the pressure inside the compressor before doing the
replacement of each compressor parts to prevent accident.
4-Step Capacity
Control
Step-less
Capacity Control
3
II-1. DISMANTLE CAPACITY SOLENOID VALVE
Step 1. Loosen the lock nut of the three solenoid valves

using a wrench and remove the solenoid coil.
Step 2. Loosen all the screws of solenoid valve and

take out the solenoid valve.
Step 3. Remove the capillary tube from the compressor

casing.
4
Step 4. Loosen the 90 deg. elbow oil inlet connector of
the compressor casing and remove it.
II-2. ASSEMBLY COVER PLATE
Step 1. Clean first the surface of the compressor casing

using oilstone and wipe it with a clean cloth or rag. Also
clean the oil line hole using pressurize air.
Step 2. Put the two O-ring in the cover plate.

O-ring
5
Step 3. Install the cover plate in the compressor casing
and tighten all the screws.
Cover Plate N.O. Solenoid

Valve
Orifice Plate
II-3. ASSEMBLY CAPACITY SOLENOID VALVE (N.C)
Step 1. Put the two O-rings in orifice plate and put it in

the compressor casing.
O-rings and hole must
be in same position
Orifice plate
6
Step 2. Put the two O-rings in N.C. capacity solenoid
valve.
Orifice Plate
Step 3. Install the N.C. capacity solenoid valve and the

orifice plate in the compressor casing.
Step 4. Put all the screws and tighten it using a wrench.
7
II-4. ASSEMBLY CAPACITY SOLENOID VALVE (N.O)
Step 1. Install first the oil inlet connector in the

compressor casing using a wrench.
Step 2. Install the N.O. capacity solenoid valve in the oil

inlet connector using a wrench. Make sure that the flow
mark in the solenoid valve is correct (1 2). There is a
check valve in this valve body.
Step 3. Install the 90 deg. elbow connector in the

capacity solenoid valve and in the compressor casing
using a wrench.
Step 4. Install the capillary tube in the two 90 deg. elbow

connector.
8
Step 5. Install the capacity solenoid coil in the capacity
solenoid valve and tighten it.
III. HOW TO CHANGE STEP-LESS TO 4-STEP CAPACITY CONTROL

Step-less
Capacity Control
4-Steps Capacity
Control
9
III-1. DISMANTLE CAPACITY SOLENOID VALVE (N.C)
Step 1. Dismantle the solenoid coil of the capacity

solenoid valve.
Step 2. Loosen all the screw of capacity cover plate

and remove it.
Step 3. Loosen all the screw of capacity solenoid valve

(N.C) and remove it.
III-2. DISMANTLE CAPACITY SOLENOID VALVE (N.O)
Step 1. Loosen the capillary tube from 90 deg. elbow

connector using a wrench.
10
Step 2. Loosen the 90 deg. elbow connector from the
capacity solenoid valve.
Step 3. Loosen the N.O capacity solenoid valve from oil

inlet connector.
Step 4. Loosen the oil inlet connector from compressor

casing.
III-3. ASSEMBLY CAPILLARY
Step 1. Install first the 90 deg. elbow connector (with

tape sealant) in the compressor casing using a wrench.
11
Step 2. Install the capillary on the 90 deg. elbow
connector.
III-4. ASSEMBLY 4-STEPS CAPACITY SOLENOID VALVE
Step 1. Clean first the surface of the compressor casing

using oilstone and clean the oil hole using pressurized
air.
Step 2. Put O-ring in the capacity solenoid valve.
Make sure O-rings and

the two holes must be
in same position
Step 3. Install the capacity solenoid valve in the

compressor casing and put all screw and tighten it.
12
Step 4. Install the solenoid coil on capacity solenoid
valve and tighten it.
IV. HOW TO REPLACE OIL FILTER, OIL LEVEL SWITCH
NOTE: If the compressor is still in the chiller system, be sure to pump down first the
system then close the stop valves and release the high pressure inside the
compressor before removing or replacing any part for servicing, to prevent any
accident to happen in the jobsite.
IV-1. DISMANTLE OIL FILTER FLANGE
Step 1. Recover first the lubrication oil of the

compressor by loosening the angle valve of the service
flange or oil filter flange and drain the lubrication oil.
Another way is to loosen all the bolts of oil filter flange
and take out the flange to drain the oil.
13
Step 2. After draining all the lubrication oil, loosen all
the screw bolts of the oil filter flange and pull out the oil
filter flange.
IV-2. CHANGE OIL FILTER
Step 1. Put the oil filter flange in the clamp to fix it.
Step 2. Loosen the oil filter nut using a wrench.
14
Step 3. Take out the oil filter and clean the flange using
air or wipe it with a piece of cloth or rag.
Step 4. Put loctite sealant in the end side screw of oil

filter flange.
Loctite Sealant
Step 5. Install the new oil filter to oil filter flange and
tighten it using a wrench with a torque of 850 kg-cm.
IV-3. ASSEMBLY OIL FILTER TO CASING
Step 1. Put oil filters inner (Teflon) and outer gasket to

oil filter flange.
Teflon inner gasket
Non-asbestos outer
gasket
15
Step 2. Install oil filter assembly to compressor casing.
Step 3. Install all hexagonal screw bolts and tighten it

using a hexagonal wrench or torque wrench with a
torque value of 1000 kg-cm.
IV-4. DISMANTLE OIL LEVEL SWITCH COVER
Step 1. Use a torque wrench or hexagonal wrench to

loosen the bolts of oil switch cover.
Step 2. Take out the magnet from the crankcase and

clean it using air or piece of cloth.
Take this magnet
out and clean
16
Step 3. Check the oil switch using a tester by
connecting the two lines of the oil switch to tester
terminal line.
The switch ON when
the oil level is high
The switch OFF when

the oil level is low
IV-5. ASSEMBLY OIL LEVEL SWITCH COVER TO

CASING
Step 1. Put the magnet back in the crankcase, as close

as possible to oil filter.
Step 2. Put the new gasket in oil switch cover and

install it to compressor casing and put all screw bolts
and tighten it using a hexagonal wrench or torque
wrench with a torque 1000 kg-cm.
Gasket
17
V. HOW TO REPLACE SUCTION FILTER
NOTE: If the compressor is still connected in the chiller system, make sure to pump
down the system and release the pressure inside the compressor before replacing any
parts of the compressor, to prevent any accident to happen in the jobsite.
V-1. DISMANTLE SUCTION FLANGE
Step 1. Loosen all the hexagonal screw bolts of the

suction flange using a wrench.
NOTE: If the stop valve is connected directly

in the suction flange, loosen first the entire
screw bolt and remove the stop valve.
Step 2. Disconnect the suction piping from the

compressor.
18
Step 3. Remove the gaskets and the suction filter from
the compressor.
V-2. ASSEMBLY SUCTION FILTER
Step 1. Put suction filter inner gasket in the motor

casing suction flange before installing the suction filter.
Inner Gasket
Step 2. Install the suction filter in the compressor casing.
Step 3. Put suction filter outer gasket in the motor

casing suction flange.
Outer Gasket
Step 4. Install the suction flange with bolts and tighten it

using a hexagonal wrench or torque wrench.
Refer to index, table 3 of this handbook for
tightening torque settings for compressor
accessories.
19
VI. HOW TO REPLACE CHECK VALVE, OIL SEPARATOR
VI-1. DISMANTLE CHECK VALVE
Step 1. Disconnect first the discharge piping of the

chiller system from the check valve.
NOTE: If the service/stop valve is connected

directly to compressor discharge piping, loosen
first the entire screw bolts and remove the stop
valve.
Remove the
service/stop valve
Step 2. Loosen all the bolts of check valve and after

loosening all the bolts, remove the check valve from the
oil separator.
Step 4. Remove the check valve from oil separator and

remove the gasket.
Change this gasket
with new
20
VI-2. DISMANTLE OIL SEPARATOR
Step 1. Install eyebolt in oil separator and lift it using an

overhead crane and loosen all the bolts of oil separator.
Step 2. Pull out the oil separator from compressor

casing.
Eyebolt and steel rope
connected to overhead crane
VI-3. CLEAN OIL SEPARATOR
Step 1. Lift the oil separator using overhead crane and

use pressurize oil to clean the oil separator mesh
screen, or dismantle the oil separator mesh screen to
clean it (for RC series new design).
Step 2. Wipe the inner portion of the oil separator with

a piece of cloth or rag.
21
Step 3. Use an oilstone to clean the surface of the oil
separator and wipe it with a piece of cloth or rag.
VI-4. ASSEMBLY OIL SEPARATOR TO COMPRESSOR
Step 1. Put new Teflon gasket in the bearing seat

discharge side.
Teflon gasket
Step 2. Put oil separator gasket in the compressor

casing. Use screw bar on both side of the casing to
secure the gasket, and it will also hold the oil separator
when installing.
New gasket
Step 3. Install the oil separator in the compressor and

put all screw bolts and tighten it using a wrench or
torque wrench.
For M20 screw bolt, 3800 kg-cm of torque.
For M16 screw bolt, 2000 kg-cm of torque.
Refer also to index of this handbook for other
torque settings for screw bolts.
22
VI-5. ASSEMBLY CHECK VALVE
Step 1. Put new gasket on oil separator discharge side.
New gasket
Step 2. Install check valve on oil separator discharge

port and put all the screw bolts and tighten it using a
wrench with a torque value of 1600 kg-cm.
Step 3. Put new gasket in the check valve.
Step 4. Install the discharge piping or stop valve on the

check valve and put all screw bolts and tighten it using
a wrench with a torque value of 1600 kg-cm.
23
VII. HOW TO REPLACE MOTOR ASSEMBLY, MOTOR STATOR
VII-1. DISMANTLE ELECTRICAL CABLE PLATE
Step 1. Loosen all the screw bolts of electrical cable

plate using a wrench or air drive spanner.
Step 2. Use screw gauge to hold the cover plate and

loosen the copper nut from motor cable plate terminal.
Screw gauges
Step 3. Take out the motor cable plate and the gasket.
VII-2. DISMANTLE MOTOR ASSEMBLY, MOTOR ROTOR
Step 1. Use a rope to hold the motor assembly and

hang it using an overhead crane, and then loosen all
the screw bolts using torque wrench or hexagonal
wrench.
24
Step 2. Remove all screw bolts and pull out the motor
assembly slowly.
Step 3. Loosen the bolt of motor rotor using a wrench

or air drive spanner.
Step 4. Pull out the motor rotor and remove the rotor
key.
NOTE: Use a rope for bigger model to take out the
motor rotor.
VII-3. DISMANTLE MOTOR STATOR
These procedures are for small models only

(RC12~RC18)
Step 1. Loosen first all the bolts of motor stator guide
vane and remove the guide vane.
25
Step 2. Install the hydraulic puller in the motor casing.
Step 3. Operate the controller of the hydraulic puller to

take out the motor stator slowly. (This used pressure to
take out the motor stator from the motor casing.)
NOTE: For Bigger Models (RC19~RC21), Follow the

procedures given below: (This is the slide-in to take
out the motor stator)
Step 1. Install first the motor stator holder and hang it

using an overhead crane.
26
Step 2. Loosen the motor stator fix pin using a wrench.
Step 3. Remove the motor stator fix pin and the O-ring.
Step 4. Lift the motor stator using an overhead crane.

(This is slide-in to take out the motor stator from the
motor casing.)
VII-4. ASSEMBLY MOTOR STATOR
NOTE: These procedures are for RC12~RC18

models only. (This is the press-in to insert the
motor stator)
Step 1. Put first the motor stator to motor stator fix jig.
27
Step 2. Lift the motor stator using an overhead crane
and put it in the hydraulic press machine.
Step 3. Insert the motor stator key and hammer it.
Motor stator key
Step 4. Lift the motor casing and put it on top of the

motor stator. Make sure the slot in the motor casing and
the location of the key is in the same position. This
used pressure to insert the motor stator to motor casing.
Step 5. Operate the hydraulic press machine to insert

the motor stator to motor casing. After the motor stator
is fitted in the motor casing, press the upward button of
the press machine.
Step 6. Lift the motor assembly using a crane and put it

in the pallet.
28
Step 7. Install the motor stator guide vane to motor
assembly. Make sure to put loctite first in the screw
hole before installing the guide vane.
NOTE: These procedures are for RC19~RC21

models.
Step 1. Put first the motor stator to motor stator fix jig
and lift it using overhead crane.
Step 2. Put slowly the motor stator in the motor casing.
This two hole must be

in the same position
Step 3. Check if the two holes are in the same position.
Check this hole
29
Step 4. Install the motor stator fix pin to motor casing.
Make sure to put new O-ring
Step 5. Tighten the motor stator fix pin using a wrench.
VII-5 ASSEMBLY MOTOR ROTOR
Step 1. Put the motor rotor key on male screw rotor.
Step 2. Install the motor rotor in the male screw rotor

shaft.
NOTE: Use a rope for bigger models.
30
The number is close to
suction bearing position
Step 3. Put loctite sealant on M16 screw bolt with

washer and install it. Loctite sealant
Step 4. Check the motor rotors alignment using a dial

gauge. Rotate the rotor in counterclockwise direction;
the reading should not exceed 0.15 mm.
VII-6. ASSEMBLY MOTOR TO COMPRESSOR
Step 1. Lift the motor assembly using an overhead

crane and put new gasket on motor assembly.
31
Step 2. Install motor assembly in the compressor.
Step 3. Pull out the motor cable terminal wire from the
compressor casing terminal housing and put the new
motor cable gasket in the compressor casing.
New gasket
There are symbol

marked U,V,W,Z,X,Y in
the terminal
Step 4. Install all hexagonal screw bolts in the motor

assembly and tighten it using a torque wrench or
hexagonal wrench.
Refer to index of this manual for tightening torque
settings for screw bolts.
VII-7. ASSEMBLY MOTOR CABLE PLATE
Step 1. Install first the screw gauges in the compressor

casing then put the motor cable plate.
32
Step 2. Connect the motor cable terminals to cover
plate terminal bolts. Motor cable marks should
correspond to cover plate terminal bolts. Install the
screw nut with one washer each terminal and tighten all
the screw nut using a wrench or spanner and connect
also the temperature sensor terminal.
Terminals: U-U, V-V, W-W, Z-Z, X-X,

and Y-Y the same mark in cable plate
terminals and motor cable wires.

using a torque wrench or hexagonal wrench with a
torque value of 1000 kg-cm.
Step 4. Test the motor insulation and resistance of each

terminal.
NOTE: Refer to Index, table 2 for insulation test

standard.
33
VIII. HOW TO REPLACE PISTON, PISTON ROD, AND SLIDE VALVE
VIII-1. DISMANTLE OIL SEPARATOR
Step 1. Lift first the compressor and put it in the

adjustable table and fix the two opposite base using
screw bolt.
Note: In case there is no adjustable table in the job
site, use a table that is capable of carrying the
compressor.
Step 2. Dismantle the check valve, use a wrench to

loosen the bolts and remove the check valve.
Step 3. Install two eyebolts in the oil separator and

hang it using a crane, then loosen all the bolts of the oil
separator.
Step 4. Take out the oil separator from the compressor.
34
VIII-2. DISMANTLE PISTON, PISTON ROD
Step 1. Loosen all the screw bolts of discharge cover

plate then remove the cover plate.
Step 2. Take out the disc spring and discharge bearing

fixed ring.
Step 3. Loosen the screw bolt of the piston and remove it.
Step 4. Pull out the piston, piston spring, and copper

washer.
Step 5. Use a torque wrench to take out the piston rod.
35
VIII-3. DISMANTLE BEARING SEAT, SLIDE VALVE
Step 1.Loosen the bolts of the bearing seat using a wrench.
Step 2. Remove the 2 two guide pin from the bearing seat.
Guide pin
Step 3. Install two eyebolt in the bearing seat and lift the
bearing seat slowly using an overhead crane.
Step 4. Loosen the bolt of slide valve key using

hexagonal wrench and take out the key.
36
Step 5. Take out the slide valve.
VIII-4. ASSEMBLY SLIDE VALVE
Step 1. Use a file or grinding wheel to slightly clean the

sharp edges of the slide valve.
Slightly grind the

surface to eliminate
the sharp edges
37
Step 2. Clean the oil circuits of the compressor casing
using pressurize air.
Step 3. Install the slide valve in the compressor casing.

Make sure that the slide valve can be move smoothly.
Refer to Index, table 6 for the Clearance.
Step 4. Put loctite sealant on the bolt of the slide valve

key.
Loctite sealant
Step 5. Install the slide valve key and tighten using a

hexagonal wrench.
Refer to index of this manual for screw bolts
tightening torque settings.
Step 6. Check again the slide valve if it can be moved

smoothly.
38
VIII-5. ASSEMBLY BEARING SEAT
Step 1. Put loctite sealant in the surface of the

compressor casing. Be careful not to drop any amount
of sealant inside the chamber.
Loctite sealant
Step 2. Lift the bearing seat and install it carefully in the

compressor casing.
Step 3. Fix the guide pin on the two opposite sides of

the bearing seat by hammering it.
Guide pin

using a torque wrench or hexagonal wrench.
Refer to index of this manual for screw bolts
tightening torque settings.
39
VIII-6. ASSEMBLY PISTON ROD, PISTON
Step 1. Put loctite sealant on piston rods screw and

install it in the slide valve using a torque wrench with a
torque of 1000 kg-cm. Check again the slide valve by
moving the piston rod forward and backward. It should
be move smoothly.
Loctite sealant
Push and pull the piston rod

if the slide valve is moving
smoothly.
Step 2. Put some lubrication oil in the piston cylinder

and install the copper washer.
Copper washer
40
Step 3. Install first the piston O-ring, piston ring, and
piston guide ring in the piston.
Piston O-ring
Piston ring
Piston guide ring
Step 4. Fix the piston to piston gauge.
Piston gauge
Piston
41
Step 5. Install the piston with spring in the piston rod.
Be careful not to drop the copper washer in the cylinder.
Guide ring
Step 6. Install the bolt with washer and check the piston
by pushing it to the end and it should be back to at least
75% of its original position.
VIII-7. ASSEMBLY DISCHARGE COVER PLATE
Step 1. Put some lubrication oil in the discharge bearing.
Step 2. Install the discharge bearing fixed ring for male

and female rotors.
42
Step 3. Install the disc spring for male and female rotors.
Step 4. Install the discharge cover plate with new

gasket.
Gasket
Step 5. Put all hexagonal bolts and tighten it using a

hexagonal wrench or torque wrench with a torque of
1000 kg-cm.
Refer to index of this manual for other screw bolts
torque settings.
43
IX. HOW TO REPLACE MALE AND FEMALE ROTORS, BEARINGS
NOTE: Follow first the dismantling procedures given in item VII (VII-1~VII-2) and
itemVIII (VIII-1~VIII-3).
IX-1. DISMANTLE BEARING SLOT NUT
Step 1. Install first the male rotor fixed gauge in the

male rotor suction side.
Male rotor assembly
fixed gauge
Step 2. Loosen the bearing slot nut using slot nut

tightening gauge for male and female rotors.
Slot nut tightening gauge
Step 3. Remove the male rotor fixed gauge and lift the
bearing seat slowly using an overhead crane.
44
IX-2. DISMANTLE MALE AND FEMALE ROTORS
Step 1. Put a cylinder in the hydraulic press machine

and put inside the cylinder the bearing seat to take out
the male and female rotor.
Cylinder
Steel bar, to push down

the rotor gradually
NOTE: ANOTHER WAY TO TAKE OUT THE MALE

AND FEMALE ROTOR
Step 2. Use the Circle tool for loosening the bearing

(refer to index of this manual for the list of this tools)
and use a puller. First, install the circle tool for
loosening the bearings on the male or female bearing
housing. Install a steel bar on top of the rotor shaft
and install the puller. The steel bar will push
down the rotor shaft gradually
when tightening the puller.
Puller
Circle tool for

loosening bearings
45
IX-3. DISMANTLE DISCHARGE AND SUCTION BEARINGS
Step 1. Remove first the discharge bearings from the

bearing seat by hammering.
Step 2. Remove the inner ring of male and female rotor.

This can be done by heating the inner ring with the used
of acetylene or by the use of grinder to cut the inner ring
(be careful not to cut the screw rotor). After cutting the
bearing inner ring, use a chisel and hammer it to take out
the inner ring.
Grinding wheel
Step 3. Loosen the bearing fix ring of the male suction

bearing and take out the bearings by hammering.
46
Step 4. Loosen the bearing fix bolt of the female
suction bearing and take out the bearings by
hammering.
IX-4. ASSEMBLY MALE AND FEMALE ROTORS, DISCHARGE BEARINGS
Step 1. Prepare and measure first the new male and

female rotors neck and the bearing seat male and
female bearings hole.
NOTE: Calculation on how to get a balance piston

and inner/outer spacer ring.
EQUATION: D1-D2=C2-T2+0.12mm
D balance=C1-T1+0.12mm
T2+D1=C2+D2+0.12mm
FOR MALE and FEMALE ROTORS
T1 thickness of male rotor neck

T2 thickness of female rotor neck
47
FOR BEARING SEAT
C1 thickness of bearing seat male bearing hole

C2 thickness of bearing seat female bearing hole
FOR SPACER RING and BALANCE PISTON
D thickness of balance piston

D1 thickness of inner spacer ring
D2 thickness of outer spacer ring
Balance piston,
Inner spacer ring
Outer spacer ring
48
Step 2. Clean the male and female rotors using oilstone
and grinding wheel. Do this on both the suction and
discharge side of the male and female rotors.
Step 3. Install first the male rotor in the compressor

casing, and then the female rotor.
49
Step 4. Heat the bearings inner ring for male and
female rotor, about 80 deg. C.
Heater Plate
Step 5. Insert first the bearings inner ring and inner

spacer ring in the female rotor (it must be at the bottom).
Radial bearing inner ring
Inner spacer ring
Step 6. Clean the bearing seat using oilstone and

grinding wheel to remove the sharp edges.
Step 7. Put first the bearings outer ring and then the
outer spacer ring in the bearing seat female hole and
hammer it.
Outer spacer ring
Radial bearing outer ring
Step 8. Lift the bearing seat using an overhead crane

and put it in the compressor casing.
50
Step 9. Install two guide pin and hammer it.
Step 10. Put the balance piston on the male rotor.
This face upside position
This face at the bottom
Step 11. Put the male rotor discharge bearing outer

ring and hammer it.
Radial bearing outer ring
51
Step 12. Put the male rotor discharge bearing inner ring.
Wait for a few seconds to cool and hammer it.
Male Rotor radial bearing

inner ring
Step 13. Heat the male and female axial bearing up to 80C.
Step 14. Install the axial bearing for male and female
rotors. Three bearings each for male and female rotors.
Bearing position: Two bearings with series number
faced down, the third bearing with series number
faced up.
NOTE: Refer to Index, table 2 of this handbook for
the types of bearings for all models.
Bearing position: The first and second

bearing position is the series number
face down and the third bearing
position is the series number face up.
1st 2nd 3rd

52
Step 15. Install the rotor assembly fixed gauge on the
suction side of the male rotor.
Rotor assembly
fixed gauge
Step 16. Put loctite sealant on male and female rotor end
side screw and install the bearing slot nut.
Loctite sealant
Step 17. Put the slot nut tightening gauge and tighten it
using a torque wrench.
Refer to the table below for the torque settings.
Torque Value (Kg-m)

MODEL Male Female
RC12RC13 24 16
RC14RC15L 40 20
RC16RC17 56 28
RC18 56 34
RC19~RC21 47 47
RC22RC24 56 56
53
Step 18. Remove the rotor assembly fixed gauge and
the two guide pin.
Step 19. Lift the bearing assembly and check the

discharge clearance of male and female rotors to
bearing seat using a thickness gauge.
Refer to table below for the discharge clearance of

male and female rotors to bearing seat.
Model
RC12~RC13 RC14~RC15 RC16~RC18 RC19~RC21 RC22~RC24
Item
Standard (mm) 0.04~0.08 0.04~0.09 0.04~0.1 0.04~0.1 0.04~0.1
54
IX-5. ASSEMBLY SUCTION BEARINGS
Step 1. Heat first the radial bearing inner ring, inner

spacer ring of the male rotor and the radial bearing
inner ring of the female rotor for about 80 C.
Step 2. Insert the inner ring, inner spacer ring on the

male rotor.
Bearings inner ring
Inner spacer ring
Bearings inner ring
Step 3. Use a chisel to mark the male rotor, to prevent

the inner ring and inner spacer ring from dropping or
moving.
55
Step 4. Insert the inner ring on the female rotor.
Step 5. Install the oil-guiding ring in the compressor

casing, for male rotor and hammer it.
Step 6. Install the first suction radial bearing outer ring.
Trumpet shape tool for

tightening suction bearing
Step 7. Install the suction outer spacer ring and hammer it.
Step 8. Install the second suction radial bearing outer ring.
56
Step 9. Put loctite sealant on the screw hole and install
the suction bearing fixed ring. Put all screw bolts and
tighten it using a torque wrench or hexagonal wrench.
Refer to index of this manual for screw bolts torque
settings.
Suction bearing
fixed ring
Step 10. Install the oil-guiding ring in the compressor

casing, for female rotor and hammer it.
Step 11. Install the radial bearing outer ring.
Step 12. Put loctite sealant on screw hole and install the
screw bolt with washer.
Screw bolt with
washer
57
IX-6. ASSEMBLY OIL SEPARATOR
NOTE: Before assembling the oil separator, assemble first the bearing seat. Follow the
procedures given in item VIII (VIII-5~VIII-7).
Step 1. Clean the oil separator flange using oilstone

and wipe it with a piece of cloth or rag.
Step 2. Put new Teflon gasket in the bearing seats

discharge port.
Teflon gasket
Step 3. Install first two screw bar in the compressor

casing and then install the oil separator gasket.
Step 4. Install the oil separator and put all the screw
bolts and tighten it using a torque wrench or hexagonal
wrench.
Refer to index of this manual for the torque settings
of screw bolts.
58
X. INDEX
Table 1. List of special tools

Item Tools Name
1 Circle Tool for Loosening Discharge Bearings (RC14~RC15LF)

2 Circle Tool for Loosening Discharge Bearings
3 Circle Tool for Loosening Discharge Bearings (RC12~RC13M)
4 Circle Tool for Loosening Discharge Bearings (RC12~RC13F)
5 Trumpet Shape Tool for Tightening Suction Bearings
6 Trumpet Shape Tool for Tightening Discharge Bearings
7 Male Rotor Assembly Fixed Gauge (RC10~RC21)
8 Tool for Tightening Discharge Bearing Inner Ring
9 Tool for Loosening Discharge Bearing from Bearing Seat

10 Tool for Loosening Suction Bearing from Compressor Casing
11 Slot Nut Tightening Gauge for Male Rotor
12 Slot Nut Tightening Gauge for Female Rotor
13 Press Tool for Piston Assembly (RC10~RC21)
14 Tool for Guide Pin
1. Circle Tool for loosening discharge bearings (RC14~RC15LF)

(B312-0014-05)
2. Circle Tool for loosening discharge bearings (RC14~RC21)
59
D
Item Number Model A B C
(P.C.D)
B312-0014-00 RC14~RC15L Male 188 136 122 150
B312-0014-01 RC16~RC17 Male 202 150 141 164
B312-0014-02 RC16~RC17 Female 162 110 101 124
B312-0014-03 RC19~RC21 Male 192 140 132 154
B312-0014-04 RC19~RC21 Female 182 130 122 144
3. Circle Tool for loosening discharge bearings (RC12~RC13M)

(B312-0014-06)
4. Circle Tool for loosening discharge bearings (RC 12~RC13F)

(B312-0014-07)
60
5. Trumpet shape tools for tightening suction bearing
F
D
Item Number Model A B C D E F

B312-0090-00 RC10~RC11 Male 55 71.5 230 200 20 30
B312-0090-11 RC10~RC11 Female 33 44.5 300 120 20 30
B312-0090-04 RC12~RC13 Male 83 99.5 260 230 105 45
B312-0090-01 RC12~RC13 Female 46 61.5 230 200 20 30
B312-0090-15 RC14~RC15 Male 103 119.5 250 220 20 45
B312-0090-00 RC14~RC15 Female 55 71.5 230 200 20 30
B312-0090-16 RC16~RC18 Male 123 139.5 170 140 20 60
B312-0090-03 RC16~RC21 Female 75 89.5 250 220 20 30
B312-0090-09 RC19~RC21 Male 133 149.5 170 140 20 45
B312-0090-10 RC22~RC24 Male 170 189.5 150 120 20 60
B312-0090-05 RC22~RC24 Female 93 109.5 260 230 20 30
6. Trumpet shape tools for tightening discharge bearing
E
F
61
Item Number Model A B C D E F
B312-0090-02 RC10~RC11 Male 63 79.5 250 220 80 30
B312-0090-13 RC10~RC13 Female 55 71.5 230 200 75 30
B312-0090-04 RC12~RC13 Male 83 99.5 260 230 105 45
B312-0090-06 RC14~RC15 Male 103 119.5 340 310 115 45
B312-0090-02 RC14~RC15 Female 63 79.5 250 220 80 30
B312-0090-08 RC16~RC18 Male 123 139.5 280 250 135 60
B312-0090-04 RC16~RC17 Female 83 99.5 260 230 105 45
B312-0090-07 RC19~RC21 Male 113 129.5 350 320 115 45
B312-0090-06 RC19~RC21 Female 103 119.5 340 310 115 45
B312-0090-08 RC22~RC24 (M), (F) 123 139.5 280 250 135 60
7. Male Rotor Assembly Fixed Gauge
Item Number Model A B C D E F G H

B312-0008-10 RC10~RC11 70 49 12.5 5 293 343 13 45
B312-0008-11 RC12~RC13 70 50 12.3 4 380 420 14 30
B312-0008-12 RC14~RC15L 80 60 12.3 4 436 470 18 40
B312-0008-13 RC16~RC18 94 74 12.3 4 475 520 18 50
B312-0008-14 RC19~RC21 105 83 22.3 6 516 550 18 55
8. Tool for tightening discharge bearing inner ring
C
D
62
Item Number Model A B C D
B312-0088-01 RC10~RC11 Male 35 47 200 170
B312-0088-00 RC10~RC13 Female 30 42 170 140
B312-0088-02 RC12~RC13 Male 45 57 210 180
B312-0088-04 RC14~RC15 Male 55 67 200 170
B312-0088-01 RC14~RC15 Female 35 47 200 170
B312-0088-07 RC16~RC18 Male 65 77 260 225
B312-0088-02 RC16~RC17 Female 45 57 210 180
B312-0088-03 RC 18 Female 50 62 220 190
B312-0088-06 RC19~RC21 Male 60 72 315 280
B312-0088-05 RC19~RC21 Female 55 67 305 270
B312-0088-07 RC22~RC24 (M), (F) 65 77 260 225
9. Tools for loosening discharge bearings from bearing seat
Item Number Model A B C D E

B312-0034-02 RC10~RC11 Female 41.5 40.5 10 100 -
B312-0034-03 RC10~RC11 Male 58 46.2 10 100 -
B312-0034-04 RC12~RC13 Female 42 40.5 10 120 -
B312-0034-05 RC12~RC13 Male 55 55 - 100 -
B312-0034-06 RC14~RC15 Female 51.8 46.2 10 120 -
B312-0034-07 RC14~RC15 Male 69.8 69.8 - 100 -
B312-0034-08 RC16~RC17 Female 61.8 58.5 10 120 -
B312-0034-09 RC16~RC18 Male 89.8 82.5 10 40 80
B312-0034-10 RC18~RC21 Female 65.8 65 10 120 -
B312-0034-11 RC19~RC21 Male 74.8 74.8 - 40 80
B312-0034-12 RC22~RC24 Female 89.8 82.5 15 65 70
B312-0034-13 RC22~RC24 Male 123.8 82.5 15 65 70
63
10. Tools for loosening suction bearings from compressor casing
C D
Item Number Model A B C D E

B312-0038-02 RC10~RC11 Female 41.9 35 15 25 200
B312-0038-03 RC10~RC11 Male 66.9 60 15 25 260
B312-0038-04 RC12~RC13 Female 43.4 42.1 15 25 190
B312-0038-05 RC12~RC13 Male 72.4 70.1 15 25 260
B312-0038-06 RC14~RC15 Female 51.9 50.1 15 25 220
B312-0038-07 RC14~RC15 Male 85.9 84.1 15 25 320
B312-0038-08 RC16~RC18 Female 65.9 65.1 15 30 260
B312-0038-09 RC16~RC18 Male 97.9 95.4 15 30 360
B312-0038-10 RC19~RC21 Female 69.9 60.1 15 30 380
B312-0038-11 RC19~RC21 Male 104.9 101.4 15 30 450
B312-0038-12 RC22~RC24 Female 84.9 65 20 30 480
B312-0038-13 RC22~RC24 Male 129.9 113.5 20 30 480
11. Slot nut tightening gauge for male rotor

h
d2
W
D5
D6
A
D1
D4
D3
D2
L1
L
64
Item Number Model D1 D2 D3 D4 D5 D6 W L1 L d2 h
B312-0091-02 RC10~RC11 80 61 53 63 52.3 48.3 4.7 0 33 61 19.2
B312-0091-04 RC12~RC13 100 74 66 76 65.3 60.3 5.7 33 48 74 19.2
B312-0091-06 RC14~RC15 121.5 84 76 86 75.3 69.3 6.7 31 56 84 19.2
B312-0091-08 RC16~RC17 140 94 86 96 85.3 79.3 6.7 29 57 94 25.4
B312-0091-10 RC18 140 94 86 96 85.3 79.3 6.7 0 73 94 25.4
B312-0091-12 RC19~RC21 130.5 89 81 91 80.3 74.3 6.7 102 168 89 25.4
B312-0091-14 RC22~RC24 140 94 86 96 85.3 79.3 6.7 62 96 94 25.4
12. Slot nut tightening gauge for female rotor
h
d2
W
D5
D6
A
D1
D4
D2
D3
L1
L
Item Number Model D1 D2 D3 D4 D5 D6 W L1 L d2 h

B312-0091-03 RC10~RC11 72 54 46 56 45.3 41.3 4.7 0 52 54 19.2
B312-0091-05 RC12~RC13 72 54 46 56 45.3 41.3 4.7 49 64 54 19.2
B312-0091-07 RC14~RC15 80 61 53 63 52.3 48.3 4.7 52 77 61 19.2
B312-0091-09 RC16~RC17 100 74 66 76 65.3 60.3 5.7 47 75 74 19.2
B312-0091-11 RC18 110 79 71 81 70.3 65.3 5.7 0 84 79 19.2
B312-0091-13 RC19~RC21 120.5 84 76 86 75.3 69.3 6.7 96 162 84 25.4
B312-0091-15 RC22~RC24 140 94 86 96 85.3 79.3 6.7 80 114 94 25.4
13. Press tool for piston assembly
65
Model Item Number A B
RC10~RC11 B312-0019-04 75 65
RC12~RC13 B312-0019-01 100 90
RC14~RC15L B312-0019-02 110 100
RC16~RC21 B312-0019-03 130 120
14. Tool for pin
Table 2. List of bearings
BEARING TYPE (DISCHARGE) BEARING TYPE (SUCTION)

MODEL
MALE QTY. FEMALE QTY. MALE QTY. FEMALE QTY.
7307BUO 3 7306BUO 3
RC10~11 NKI55/35 1 NKI30/30 1
NU307E 1 NU2306E 1
7309BUO 3 7306BUO 3
RC12~13 NU2211E 2 NJ2206E 1
NU309E 1 NU2306E 1
7311BUO 3 7307BUO 3
RC14~15L NU2213E 2 NJ2207E 1
NU311E 1 NU2307E 1
7313BUO 3 7309BUO 3
RC16~17 NU2216E 2 NJ2210E 1
NU313E 1 NU2309E 1
7313BUO 3 7310BUO 3
RC18 NU2216E 2 NJ2210E 1
NU313E 1 NU2310E 1
7312BUO 3 7311BUO 3
RC19~21 NU2217E 2 NJ2308E 1
NU312E 1 NU2311E 1
7313BUO 3 7313BUO 2
RC22~24 NU2318E 1 NJ2310E 1
NU313E 1 NU2313E 1
66
Table 3. Motor insulation standard
Phase to wiring
To the ground Phase to phase
temperature protector
Wiring
U V W temperature U-Z V-X W-Y U V W
protector
Should be more than 100 M
(2000M and 1000VDC)
Table 4. Compressor accessories Torque settings

Standard screw bolt Torque value (Kg-cm)
Nominal spec.
Range of reference Setting value
Motor terminal plate screw bolt M12 300 1,500 900
Oil filter joint flange M12 250 1,500 850
Oil drop / service / cleaning flange 260 1,500 850
M12
1 flange M16 200 1,000 1,000
2 flange M16 400 2,000 1,000
3 flange M20 550 2,500 2,000
4 flange M20 800 3,000 2,000
Oil sight glass P1, P3 plug 200
Table 5. Compressor screw bolt Torque settings

Standard screw bolt Torque value (Kg-cm)
Nominal spec.
Range of reference Setting value
M6 90 120 100
M8 220 290 250
M10 430 580 500
M12 750 1700 1,000
M16 1,100 3,400 2,000
M20 1,800 4,200 3,800
Table 6. Clearance between slide valve and slide valve housing

RC12~RC13 RC14~RC15 RC16~RC18 RC19~RC21
Model
Tolerance (mm) 0.025~0.055 0.03~0.06 0.04~0.07 0.04~0.07
67
HANBELL RC10~RC11 SCREW COMPRESSOR PARTS LIST
ITEM PART NO. PART NAME Q'TY SPECIFICATION
1 3131-1131A BEARING SEAT 1 FC 25
2 3130-1132A MALE SCREW ROTOR RC10 1 SAE 1141, S45C
2 3131-1132A MALE SCREW ROTOR RC11 1 SAE 1141, S45C
3 3130-1133A FEMALE SCREW ROTOR RC10 1 SAE 1141, S45C
3 3131-1133A FEMALE SCREW ROTOR RC11 1 SAE 1141, S45C
4 3131-1023A MOTOR ROTOR KEY 1 S45C, 8 * 12 * 100L
5 3131-2131A MOTOR ROTOR 1 141.4 * 140L
6 3101-1034A MOTOR ROTOR SPACER RING 1 S45C, 32 * 14.5T
7 3101-1017A MOTOR ROTOR WASHER 1 S45C, 68 * 10t
8 4303-316 SPRING WASHER 1 M16
9 4301-116060 MOTOR ROTOR SCREW BOLT 1 M16 * 60L
10 4102-NU307E MALE SCREW ROTOR DISCHARGE RADIAL BEARING 1 NU307E
11 3103-113AA MALE SCREW ROTOR OUTER SPACER RING 1 S45C, 80.3 * 7.1t
12 3103-1137B MALE SCREW ROTOR INNER SPACER RING 1 S45C, 45 * 7.1t
13 4101-7307BUO MALE SCREW ROTOR DISCHARGE AXIAL BEARING 3 7307BUO
14 4302-235 KM 7 BEARING LOCK NUT 1 KM7 (M35 * 1.5)
15 3131-1109A DISCHARGE BEARING FIXED RING (MALE) 1 S15C, 80.4 * 34.8L
16 4307-DB080 DISC SPRING (MALE) 1 SCHNORR B80
17 4102-NU2306E FEMALE SCREW ROTOR DISCHARGE RADIAL BEARING 1 NU2306
18 3101-113AA FEMALE SCREW ROTOR OUTER SPACER RING 1 S45C, 72.3 * 7.1t
19 3101-1137B FEMALE SCREW ROTOR INNER SPACER RING 1 S45C, 40 * 7.1t
20 4101-7306BUO FEMALE SCREW ROTOR DISCHARGE AXIAL BEARING 3 7306BUO
21 4302-230 KM 6 BEARING LOCK NUT 1 KM6 (M30 * 1.5)
22 3131-1111A DISCHARGE BEARING FIXED RING (FEMALE) 1 S15C, 72.4 * 54.5L
23 4307-DB071 DISC SPRING (FEMALE) 1 SCHNORR B71
24 3131-1103A-3 DISCHARGE COVER PLATE GASKET 1 REINZ AFM 34, 1.5t
25 3131-1101A DISCHARGE COVER PLATE 1 SS400, 16t
26 4301-108025 DISCHARGE COVER PLATE SCREW BOLTS 11 M8 * 1.25p * 25L
27 3131-1008A DISCHARGE EXHAUST TUBE GASKET 1 TEFLON, 5t
28 3131-1113A PISTON SPRING 1 SWPB, 2.9 N5, 41 * 125L
29 3131-1115A PISTON ROD 1 SNCM 439, 113.7L
30 4303-414 COPPER WASHER 1 14
31 3131-1116A PISTON 1 S15C, 64 * 24t
32 5112-GM69 PISTON GUIDE RING 1 TURCITE T47
33 4201-CA328 PISTON O-RING 1 CR70, I.D. 46.99 * 5.33
34 4202-T065 PISTON RING 1 S55042-0650-46N(PG4200650-T4)
35 3131-1037A WASHER 1 SS400, 20 * 5t
37 4301-110025 PISTON SCREW BOLT 1 M10 * 1.5p * 25L
38 4301-112040 BEARING SEAT SCREW BOLTS 8 M12 * 1.75p * 40L
39 3502-1102A FIXED PIN 2
40 4305-201 PLUG 1
41 3130-1141A COMPRESSOR CASING RC10 1 FC25
41 3131-1141A COMPRESSOR CASING RC11 1 FC25
42 3131-1002A-3 MOTOR CASING GASKET 1 REINZ AFM34, 1.5t
44 4301-108016 SCREW BOLT 1 M8 * 1.2 * 16L
45 4301-NKI30/30 FEMALE ROTOR SUCTION BEARING 1
46 4103-NKI55/35 MALE ROTOR SUCTION BEARING 1
47 3131-1108A SUCTION BEARING FIXED RING 1 S15C, 100 * 65 * 3t
48 4301-106010 FIXED RING SCREW BOLT 4 M6 * 1.0 * 10L
49 3131-2105A COPPER SLEEVE 1
50 3131-2111A MOTOR STATOR 1
51 3101-1143A OIL FILTER 1
52 3101-1146A OIL FILTER FLANGE INNER GASKET 1 TEFLON, 1.5t
53 3131-1144A OIL FILTER FLANGE 1 SS400, 65.9 * 63L
54 3131-1147A-3 OIL FILTER FLANGE COVER GASKET 1 REINZ AFM 34, 1.5t
55 3131-1142 OIL FILTER FLANGE COVER 1
56 4301-112035 SCREW BOLTS 4 M12 * 1.75 * 45
57 3131-1168A OIL FLOW REGULATOR PLUG 1 1/8 NPT, 1.2
58 4305-102 PLUG 1 1/4 PT
59 3131-1167A-3 OIL COOLER CONNECTOR COVER GASKET 1 REINZ AFM 34, 1.5t
60 3131-1169A OIL COOLER CONNECTOR COVER 1 SS400, 80 * 50 * 12t
61 4301-110025 CONNECTOR COVER SCREW BOLTS 6 M10 * 1.5p * 25L
62 4304-101 90C ELBOW 2 1/4 F * 1/4 NPT, A - 4890
63 3101-1145E CAPILLARY 1
64 3101-1003A SOLENOID VALVE GASKET 2 NOK, 1515SPS
65 4301-804012 SOLENOID VALVE SCREW BOLTS 8 M4 * 0.7 * 12L
66 4401-32 SOLENOID VALVE STEP CONTROL (NC) 2 O.D.E. 2743K0R30 4344
67 4402-03 SOLENOID VALVE COIL 220V 2 O.D.E. BDV08224DU, 50/60Hz
68 4201-VP021 O-RING 1
68
69 3101-1153 PLUG, 3/8PT 1
70 3130-1512B SLIDE VALVE Vi = 3.5 RC10 1 FCD 50
70 3131-1112B SLIDE VALVE Vi = 2.6 RC11 1 FCD 50
71 3101-1114A SLIDE VALVE KEY 1 S45C, 16 * 27 * 12
72 4301-106010 SCREW BOLT 1
73 3131-1147A-3 SERVICE FLANGE GASKET 1 REINZ AFM 34, 1.5t
74 3131-1142 SERVICE FLANGE 1
75 4301-112035 SERVICE FLANGE SCREW BOLTS 4 M12 * 1.75 * 45
76 4201-VP021 O-RING 1 (P21) 2
77 3131-2102A MOTOR STATOR FIXED PIN 1 S45C
78 4304-114 REFRIGERANT CONNECTOR 1 180 DEG, 3/8 F * 3/8 NPT
79 4302-311 REFRIGERANT CONNECTOR COPPER SCREW NUT 1 3/8 F
80 4302-312 REFRIGERANT CONNECTOR COPPER COVER 1 3/8 F
81 3131-1006B-3 MOTOR CABLE PLATE GASKET 1 REINZ AFM 34, 1.5t
82 3131-1040B MOTOR CABLE PLATE 1 S20C, 180 * 22t
83 3131-1014B MOTOR CABLE BOX GASKET 1
84 4301-112045 MOTOR CABLE SCREW BOLTS 6 M12 * 1.75p * 45
85 4301-108016 CABLE BOX SCREW BOLTS 3 M8 * 1.2 * 16L
86 3131-1012B ELECTRICAL CABLE BOX 1
87 3131-1013A ELECTRICAL CABLE BOX COVER 1
88 4806-33 CABLE BOX HOLE STOPPER 1 19, HP 19
89 3101-1007A CABLE BOX FLANGE GASKET 1
90 3101-1021B CABLE BOX FLANGE 1
91 4301-108016 CABLE BOX FLANGE SCREW BOLTS 4
92 4405-15 MOTOR PROTECTIVE CONTROLLER INT 69, 220V 1 KRIWAN, 52A120S10
93 4301-804020 SCREW BOLTS 2 M4 * 0.7 * 20L
94 4303-104 WASHER 2
95 4303-304 SPRING WASHER 2 MA
96 4302-104 SCREW NUT 2
97 4301-108016 SCREW BOLT 4
98 3131-2201A MOTOR COVER 1 FC30
99 4301-114 3/8 NPT CONNECTOR 1
100 4302-311 COPPER NUT 1
101 4302-312 COPPER NUT COVER 1
102 4304-102 1/4" NPT CONNECTOR 1
103 4304-201 1/4 NPT TERMINAL 1
104 4304-106 ANGLE VALVE 1 CASTEL6110/22, SAE
105 4302-303 COPPER NUT 1 A-414
106 4304-301 COPPER NUT COVER 1
107 4301-112045 MOTOR COVER SCREW BOLTS 16 M12 * 1.75 * 45
108 3131-1004A-3 SUCTION FILTER INNER GASKET 1 REINZ AFM 34, 1.5t
109 3131-1024A SUCTION FILTER 1
110 3131-1004A-3 SUCTION FILTER OUTER GASKET 1 REINZ AFM 34, 1.5t
111 3188-8700 SUCTION STOP VALVE 1
112 4301-116120 STOP VALVE SCREW BOLTS 4
113 3131-1004A-3 SUCTION FLANGE GASKET 1 REINZ AFM 34, 1.5t
114 3131-101EA SUCTION FLANGE COUPLING 1
115 3131-1019A SUCTION FLANGE 1 SS400
116 4301-116055 FLANGE SCREW BOLTS 4 M16 * 55L
117 3131-1801A OIL SEPARATOR 1 ASME, SA395, GRADE 60
118 3131-1001A-3 OIL SEPARATOR GASKET 1 REINZ AFM 34, 1.5t
119 3131-1811A DISCHARGE EXHAUST TUBE SILENCER 1
120 3131-1809A OIL SEPARATOR FILTERING SLAB (INNER) 1
121 3131-1804B OIL SEPARATOR MESH 1
122 3131-1809A OIL SEPARATOR FILTERING SLAB (OUTER) 1
124 4301-112090 SCREW BOLTS 3 M12 * 1.75p * 90L
125 4201-VA119 O-RING 1
126 4804-01 OIL SIGHT GLASS 1 ALCO
127 4305-105 PLUG 1/4 NPT 1 1/4 NPT * 11L
128 4305-107 PLUG 1/8 NPT 1 1/8 NPT
129 3101-1051C OIL HEATER, 220V 150W 1 UL, AWG#18
130 4806-28 ELECTRICAL BOX CABLE HOLE PLUG 3/8 PF 1 PF 38, FGA 17 10
131 4405-16 DISCHARGE TEMPERATURE SENSOR 110C 1 KRIWAN, PTC, 02D512S36
132 4305-105 PLUG 1/4 NPT 1 1/4 NPT * 11L
133 4304-106 ANGLE VALVE 1 CASTEL6110/22, SAE
134 4302-303 COPPER SCREW NUT 1 A-414
135 4304-301 COPPER COVER 1
136 4301-116055 CHECK VALVE SCREW BOLTS 4 M16 * 55L
137 3188-7100A DISCHARGE CHECK VALVE 1 1
138 3101-1005A-3 DISCHARGE FLANGE GASKET, 1 1 REINZ AFM 34, 1.5t
139 3101-101AB DISCHARGE FLANGE COUPLING 1
140 3101-1019B DISCHARGE FLANGE 1 FCD 50
141 4301-116050 DISCHARGE FLANGE SCREW BOLTS
69
1 3101-1131B BEARING SEAT (RC12) 1 FC25
2 3101-1132C MALE ROTOR 1 S45C
2 3102-1132C MALE ROTOR (RC13) 1 S45C
3 3101-1133B FEMALE ROTOR 1 S45C
3 3102-1133B FEMALE ROTOR (RC13) 1 S45C
4 3102-1023A KEY OF MOTOR ROTOR 1 8*12*135 S45C
5 3101-1134A BALANCE PISTON 1 62.7*7.04 S45C
6 4102-NU309E DISCHARGE BEARING (TRANSVERSE, MALE) 1 NU309ECP
7 4101-7309BUO DISCHARGE BEARING (LONGITUDINAL, MALE) 3 7309BEGAP/7309B.TVP.UO
8 4302-245 KM9 BEARING SLOT NUT (MALE ROTOR) 1 M45*1.5 KM9
9 3101-1109A DISCHARGE FIXED RING (MALE ROTOR) 1 100*88.3 S15C
10 4307-DB100 DISC SPRING (MALE ROTOR) 1 SCHNORR B100
11 4102-NU2306E DISCHARGE BEARING OF FEMALE ROTOR (TRANSVERSE) 1 NU2306ECP
12 3101-1137B INNER SPACER RING OF FEMALE ROTOR 1 47*7.1t S45C
13 3101-113AA OUTER SPACER RING OF FEMALE ROTOR 1 72.3*7.1t S45C
14 4101-7306BUO DISCHARGE BEARING OF FEMALE ROTOR (LONGITUDINAL) 3 7306BEGAP/7306B.TVP.UO
15 3102-1111B DISCHARGE FIXED RING (FEMALE ROTOR) 1 72*107.7L S15C
16 4302-230 KM6 BEARING SLOT NUT (FEMALE ROTOR) 1 M30*1.5 KM6
17 4307-DB071 DISC SPRING (FEMALE ROTOR) 1 SCHNORR B71
18 3101-1103A-3 GASKET OF DISCHARGE COVER PLATE 1 REINZ-AFM 34, 1.5t
19 3101-1101A DISCHARGE COVER PLATE 1 SS400
20 4301-110035 BOLT (END PLATE) 13 M10*1.5*35L
21 3102-1113A PISTON SPRING 1 40*125L SWP B
23 3101-1115A PISTON ROD (RC12) 1 130.2L SNCM 439
24 4303-420 COPPER WASHER 1 M20
25 3101-1116C PISTON 1 89 S15C
26 3101-1037B WASHER 1 5mm
28 4301-112035 BOLT (FOR SLIDE VALVE FIXED) 1 M12*1.75*35L
29 5112-GM69 PISTON GUIDE RING 1 Turcite T47
30 4201-CA336 PISTON'S O-RING 1 CR70, 336-2347
31 4202-T090 PISTON RING 1 S44-0900-46N
32 3101-1008B GASKET OF DISCHARGE EXHAUST TUBE 1 TEFLON 3mm
33 4301-116040 BOLT (FOR BEARING SEAT) 8 M16*2.0*40L
34 3101-1141B COMPRESSOR CASING (RC12) 1 FC25
35 3101-1107B OIL GUIDING RING (FEMALE ROTOR) 1 62*16.5t S15C
36 4102-NJ2206E SUCTION BEARING (FEMALE ROTOR) 1 NJ2206ECP
37 4303-248 WASHER 1 1/2"*2.5mm
39 4301-112020 BOLT 1 M12*1.75*20L
40 3101-1106B OIL GUIDING RING (MALE ROTOR) 1 100*16.5 S15C
41 4102-NU2211E SUCTION BEARING (MALE ROTOR) 1 NU2211ECP
42 3101-1104A INNER SPACER RING OF SUCTION BEARING (MALE) 1 65*33.5 S15C
43 3101-1105A OUTER SPACER RING OF SUCTION BEARING (MALE) 1 100*33.5 S15C
45 3101-1108A SUCTION FIXED RING (MALE ROTOR) 1 125*3t S15C
46 4301-106016 BOLT 4 M6*1*16L
47 3101-2131A MOTOR ROTOR 1
48 3101-1017A MOTOR ROTOR WASHER 1 68*10 S45C
50 4301-116060 BOLT (FOR MOTOR ROTOR FIXED) 1 M16*2.0*60L
51 3101-1153A 3/8 PT PLUG 1
52 4201-VP021 O-RING 1 P21 VITON
53 3101-1143A OIL FILTER 1 40*200
54 3101-1146A INNER GASKET OF OIL FILTER FLANGE 1 TEFLON 1.5t
55 3101-1147A-3 OUTER GASKET OF OIL FILTER FLANGE 1 REINZ AFM 34, 1.5t
56 3101-1144A OIL FILTER FLANGE 1 FC25
57 4301-112035 BOLT 4 M12*1.75*35L
58 3142-1094 OIL COOLER CONNECTOR 3/8 NPT 1 3/8 NPT * 3/8F
59 4302-312 COPPER COVER 1 3/8 F
60 4302-311 COPPER SCREW NUT 1 3/8 F
61 4201-VA119 O-RING 1 A.R.P.119, VITON
62 3101-1168A PT PLUG 1 PT
63 4305-105 NPT PLUG 1 NPT
64 4304-115 THREE WAY CONNECTOR 1 A6330 F
66 3101-1512B SLIDE VALVE, Vi=2.2 (RC12) 1 FCD45
67 3101-1114A SLIDE VALVE KEY 1 27*16*12
70
68 4301-106016 BOLT FOR SLIDE VALVE KEY 1 M6*1*16L
69 3101-1052B OIL HEATER 220V, 150W 1
70 3101-1148A-3 GASKET OF SERVICE FLANGE 1 REINZ-AFM 34, 1.5t
71 3101-1142A SERVICE FLANGE 1 124*16t
72 4301-112035 BOLT 6 M12*1.75*35L
74 4804-01 SIGHT GLASS 1 ALCO
75 3101-1006A-3 MOTOR CABLE PLATE GASKET 1 REINZ-AFM 34, 1.5t
76 3101-1080B MOTOR CABLE PLATE 1 FC25
77 4301-112045 BOLT (FOR MOTOR CABLE COVER PLATE) 16 M12*1.75*45L
79 4301-804012 BOLT FOR SOLENOID VALVE 12 M4 * 0.7 * 12L
80 4401-32 SOLENOID VALVE (STEP CONTROL) 3 2743K0R30-4344 SDH12223DS
81 4303-104 WASHER 3
82 4302-104 SCREW NUT 3
84 3101-1153A 3/8 PT PLUG 1
85 4301-416000 EYE BOLT 2 M16
86 3132-2101A MOTOR CASING (RC12) 1 FC30
87 4301-112050 BOLT (FOR MOTOR CASING) 20 M12*1.75*50L
88 3101-1002A-3 GASKET OF MOTOR CASING 1 REINZ-AFM 34, 1.5t
89 3111-2220A MOTOR STATOR (RC12) 1 60Hz, 380V
90 3101-2104A MOTOR STATOR GUIDE VANE 1 ALUMINUM
91 3101-2103B PAD OF GUIDE VANE 1 STEEL
92 4303-308 M8 SPRING WASHER 1 M8
93 4301-108016 BOLT (FOR MOTOR STATOR GUIDE VANE) 1 M8*1.25*25L
96 3142-1094 38 NPT CONNECTOR 1 3/8 NPT * 3/8F
97 4302-312 COPPER COVER 1 3/8 F
99 4304-102 NPT CONNECTOR 1
100 4302-301 COPPER COVER 1 F
101 4302-303 COPPER SCREW NUT 1 F
102 4304-102 NPT CONNECTOR 1 NPT
103 4304-201 CONNECTOR TERMINAL 1 NPT
104 4304-106 ANGLE VALVE 1
107 3101-1004A-3 2 1/2" GASKET 1 REINZ-AFM 34, 1.5t
108 3101-1024C SUCTION FILTER 1 84*103L
109 3101-1004A-3 GASKET FOR 2 1/2" FLANGE 1 REINZ-AFM 34, 1.5t
110 3132-1800A OIL SEPARATOR (RC12) 1 FCD-500
111 4301-116050 BOLT (OIL SEPARATOR) 20 M16*2.0*50L
112 3101-1001A-3 OIL SEPARATOR GASKET 1 REINZ-AFM 34, 1.5t
113 4301-106060 SCREW BOLT 2 M6 * 60L
114 4303-306 M6 WASHER 2 M6
115 3132-1806A LOWER SLAB 1
116 3132-1809A OIL SEPARATOR MESH LOWER SLAB 1
117 3132-1804A OIL SEPARATOR MESH 1
119 4303-306 M6 WASHER 2 M6
120 4301-106060 SCREW BOLT 2 M6 * 60L
121 3132-1806A LOWER SLAB 1
122 4303-312 M12 WASHER 3 M12
123 4201-112090 SCREW BOLTS 3 M12 * 90L
124 3132-1811A DISCHARGE TUBE SILENCER 1
125 4305-105 NPT PLUG 1 NPT
126 4305-107 1/8 NPT PLUG 1 1/8 NPT
127 4405-16 DISCHARGE TEMPERATURE SENSOR 1 KRIWAN, PTC, 02D512S36
128 3101-1005A-3 1 GASKET 1 REINZ-AFM 34, 1.5t
129 3188-7100A 1 1/2" CHECK VALVE 1 1 1/2"
131 4201-NP065 O-RING 1 P65 NBR
132 3101-1015A FLANGE SHELF 1
133 3101-1019B DISCHARGE FLANGE 1 1
134 4301-116045 SCREW BOLTS 4 M16 * 45L
135 4301-116055 SCREW BOLTS 4 M16 * 55L
136 4304-106 ANGLE VALVE 1 NPT
139 4305-110 1 NPT PLUG 1 1
71
HANBELL RC14~RC15L SCREW COMPRESSOR PARTS LIST
2 3103-1132C MALE ROTOR (RC14) 1 S45C
2 3104-1132C MALE ROTOR (RC15) 1 S45C
5 3103-1134B BALANCE PISTON 1 98.8 * 18.04t, S45C
8 4302-255 KM11BEARING SLOT NUT (MALE ROTOR) 1 M55*2 KM11
9 3103-1109B DISCHARGE FIXED RING (MALE ROTOR) 1 121.9*, S15C
15 3103-1111B DISCHARGE FIXED RING (FEMALE ROTOR) 1 80.4*49.6L S15C
20 4301-112035 BOLT (END PLATE) 13 M12*1.5*35L
21 3104-1113A PISTON SPRING 1 65*140L SWP B
25 3103-1116C PISTON 1 99 S15C
26 3101-1037B WASHER 1 5mm
31 4202-T100 PISTON RING 1 S44-1000-46N
37 4303-248 WASHER 1 1/2"*2.5mm
39 4301-112020 BOLT 1 M12*1.75*20L
42 3103-1104A INNER SPACER RING OF SUCTION BEARING (MALE) 1 72*57t, S15C
43 3103-1105A OUTER SPACER RING OF SUCTION BEARING (MALE) 1 120*57t, S15C
46 4301-106016 BOLT 4 M6*1*16L
47 3103-2131A MOTOR ROTOR (RC14) 1 138*220L
47 3104-2131A MOTOR ROTOR (RC15) 1
51 3101-1153A 3/8 PT PLUG 1
53 3101-1143A OIL FILTER 1 40*200
57 4301-112035 BOLT 4 M12*1.75*35L
59 4302-312 COPPER COVER 1 3/8 F
62 3101-1168A PT PLUG 1 PT
63 4305-105 NPT PLUG 1 NPT
67 3101-1114A SLIDE VALVE KEY 1 27*16*12
72
HANBELL RC14~RC15L SCREW COMPRESSOR PARTS LIST
69 3101-1052B OIL HEATER 220V, 150W 1
72 4301-112035 BOLT 6 M12*1.75*35L
81 4303-104 WASHER 3
82 4302-104 SCREW NUT 3
84 3101-1153A 3/8 PT PLUG 1
85 4301-416000 EYE BOLT 2 M16
96 3142-1094 3/8 NPT CONNECTOR 1 3/8 NPT * 3/8F
97 4302-312 COPPER COVER 1 3/8 F
104 4304-106 ANGLE VALVE 1
107 3103-1004A-3 3" GASKET 1 REINZ-AFM 34, 1.5t
108 3101-1024C SUCTION FILTER 1 84*103L
109 3103-1004A-3 GASKET FOR 3" FLANGE 1 REINZ-AFM 34, 1.5t
113 4301-106060 SCREW BOLT 2 M6 * 60L
114 4303-306 M6 WASHER 2 M6
115 3134-1806A LOWER SLAB 1
119 4303-306 M6 WASHER 2 M6
120 4301-106060 SCREW BOLT 2 M6 * 60L
121 3134-1806A LOWER SLAB 1
122 4303-316 M16 WASHER 3 M16
123 4201-116130 SCREW BOLTS 3 M16 * 130L
125 4305-105 NPT PLUG 1 NPT
126 4305-107 1/8 NPT PLUG 1 1/8 NPT
129 3188-7200A 2" CHECK VALVE 1 2"
131 4201-NP080 O-RING 1 P80 NBR
133 3131-1019A DISCHARGE FLANGE 1 2
134 4301-116055 SCREW BOLTS 4 M16 * 55L
135 4301-116055 SCREW BOLTS 4 M16 * 55L
139 4305-110 1 NPT PLUG 1 1
73
2 3105-1132C MALE ROTOR (RC16) 1 S45C
2 3106-1132C MALE ROTOR (RC17) 1 S45C
4 3105-1023A KEY OF MOTOR ROTOR (RC16) 1 8*12*145.5L S45C
4 3106-1023A KEY OF MOTOR ROTOR (RC17) 1 8*12*190.5L S45C
9 3105-1109B DISCHARGE FIXED RING (MALE ROTOR) 1 140.4*, S15C
20 4301-112035 BOLT (END PLATE) 13 M12*1.5*35L
21 3106-1113A PISTON SPRING (INNER) 1 65*140L SWP B
22 3106-1117A PISTON SPRING (Outer) 85*175L SWP B
25 3105-1116C PISTON 1 S15C
26 3101-1037B WASHER 1 5mm
31 4202-T120 PISTON RING 1 S44-1200-46N, O.D. 120
37 4303-248 WASHER 1 1/2"*2.5mm
39 4301-112020 BOLT 1 M12*1.75*20L
46 4301-106016 BOLT 6 M6*1*16L
51 3101-1153A 3/8 PT PLUG 1
53 3105-1143A OIL FILTER 1 40*200
57 4301-112035 BOLT 4 M12*1.75*35L
59 4302-312 COPPER COVER 1 3/8 F
62 3101-1168A PT PLUG 1 PT
63 4305-105 NPT PLUG 1 NPT
67 3105-1114A SLIDE VALVE KEY 1 26*27*14.5, S45C
74
69 3101-1052B OIL HEATER 220V, 150W 1
72 4301-112035 BOLT 6 M12*1.75*35L
81 4303-104 WASHER 3
82 4302-104 SCREW NUT 3
84 3101-1153A 3/8 PT PLUG 1
85 4301-416000 EYE BOLT 2 M16
97 4302-312 COPPER COVER 1 3/8 F
104 4304-106 ANGLE VALVE 1
108 3105-1024C SUCTION FILTER 1 60 MESH
113 4301-106060 SCREW BOLT 3 M6 * 60L
114 4303-306 M6 WASHER 3 M6
115 3136-1806A LOWER SLAB 1
119 4303-306 M6 WASHER 3 M6
120 4301-106060 SCREW BOLT 3 M6 * 60L
121 3136-1806A LOWER SLAB 1
122 4303-316 M16 WASHER 3 M16
123 4201-116150 SCREW BOLTS 3 M16 * 150L
125 4305-105 NPT PLUG 1 NPT
126 4305-107 1/8 NPT PLUG 1 1/8 NPT
128 3101-1004A-3 2 1/2 GASKET 1 REINZ-AFM 34, 1.5t
129 3188-7201A 2 1/2" CHECK VALVE 1 2"
130 3101-1004A-3 2 1/2 GASKET 1 REINZ-AFM 34, 1.5t
131 4201-NP100 O-RING 1 P100 NBR
133 3102-1019A DISCHARGE FLANGE 1 2 1/2
134 4301-116055 SCREW BOLTS 4 M16 * 55L
135 4301-116055 SCREW BOLTS 4 M16 * 55L
139 4305-110 1 NPT PLUG 1 1
75
HANBELL RC18 SCREW COMPRESSOR PARTS LIST
1 3138-1131A BEARING SEAT 1 FC25
2 3138-1132A MALE ROTOR 1 S45C
3 3138-1133A FEMALE ROTOR 1 S45C
4 3138-1023A KEY OF MOTOR ROTOR 1 8*12 S45C
9 3138-1109A DISCHARGE FIXED RING (MALE ROTOR) 1 140.4*86.6t, S15C
12 3138-1137A INNER SPACER RING OF FEMALE ROTOR 1 50*7.1t, S45C
13 3138-113AA OUTER SPACER RING OF FEMALE ROTOR 1 ID 93*OD110.3*7.1t, S45C
15 3138-1111B DISCHARGE FIXED RING (FEMALE ROTOR) 1 110.4*103.9T, S15C
19 3138-1101A DISCHARGE COVER PLATE 1 16t, SS400
20 4301-112035 BOLT (END PLATE) 13 M12*1.5*35L
21 3107-1113A PISTON SPRING (INNER) 1 70*208L SWP B
22 3107-1117A PISTON SPRING (Outer) 1 85*208L SWP B
23 3138-1115A PISTON ROD (RC17) 1 SNCM 439
25 3105-1116C PISTON 1 S15C
26 3101-1037B WASHER 1 5mm
31 4202-T120 PISTON RING 1 S44-1200-46N, O.D. 120
34 3138-1141A COMPRESSOR CASING 1 FC25
37 4303-248 WASHER 1 1/2"*2.5mm
39 4301-112020 BOLT 1 M12*1.75*20L
46 4301-106016 BOLT 6 M6*1*16L
51 3101-1153A 3/8 PT PLUG 1
53 3105-1143A OIL FILTER 1 40*200
57 4301-112035 BOLT 4 M12*1.75*35L
59 4302-312 COPPER COVER 1 3/8 F
62 3101-1168A PT PLUG 1 PT
63 4305-105 NPT PLUG 1 NPT
66 3138-1512B SLIDE VALVE, Vi=2.2 1 FCD45
67 3105-1114A SLIDE VALVE KEY 1 26*27*14.5, S45C
76
69 3101-1052B OIL HEATER 220V, 150W 1
72 4301-112035 BOLT 6 M12*1.75*35L
81 4303-104 WASHER 3
82 4302-104 SCREW NUT 3
84 3101-1153A 3/8 PT PLUG 1
85 4301-416000 EYE BOLT 2 M16
86 3138-2101A MOTOR CASING 1 FC30
97 4302-312 COPPER COVER 1 3/8 F
104 4304-106 ANGLE VALVE 1
108 3105-1024C SUCTION FILTER 1 60 MESH
110 3138-1800A OIL SEPARATOR 1 FCD-500
113 4301-106060 SCREW BOLT 3 M6 * 60L
114 4303-306 M6 WASHER 3 M6
115 3138-1806A LOWER SLAB 1
119 4303-306 M6 WASHER 3 M6
120 4301-106060 SCREW BOLT 3 M6 * 60L
121 3138-1806A LOWER SLAB 1
122 4303-316 M16 WASHER 3 M16
123 4201-116130 SCREW BOLTS 3 M16 * 130L
125 4305-105 NPT PLUG 1 NPT
126 4305-107 1/8 NPT PLUG 1 1/8 NPT
129 3188-7300A 3" CHECK VALVE 1 3"
131 4201-NP120 O-RING 1 P120 NBR
133 3105-1019B DISCHARGE FLANGE 1 4
134 4301-116055 SCREW BOLTS 4 M16 * 55L
135 4301-116055 SCREW BOLTS 4 M16 * 55L
139 4305-110 1 NPT PLUG 1 1
77
1 3140-1800A OIL SEPARATOR (RC20~RC21) 1 FCD-500
2 4304-106 ANGLE VALVE 1 1/4" SAE*1/4" NPT
3 4301-120050 BOLT 4 M20*2.0*50L
4 4301-120060 BOLT 4 M20*2.0*60L
5 3103-1042A WASHER 8 M20
6 3103-1019B DISCHARGE FLANGE 1 FCD50
7 3103-101NB 3" COPPER TUBE, (FOR RC20~RC21: 3105-101IB 4) 1
3107-1005A-3 3" GASKET FOR DISCHARGE FLANGE, (FOR RC20~RC21: 4) 1 REINZ-AFM 34, 1.5t
8 3138-7100A 3" CHECK VALVE, (FOR RC20~RC21: 3140-7100A 4) 1
11 4301-112035 BOLT (END PLATE) 15 M12*1.75*35L
12 3107-1101B DISCHARGE COVER PLATE 1 SS400
16 3101-1037B WASHER 1 5mm
17 3105-1116C PISTON 1 89 S15C
20 4202-T120 PISTON RING 1 S44-1200-46N
5112-GM69 PISTON GUIDE RING 1 Turcite T47
21 3107-1115A PISTON ROD (RC19) 1 SNCM 439
21 3108-1115A PISTON ROD (R20~RC21) SNCM 439
22 3107-1113A PISTON SPRING (Inner), (FOR RC20~RC21: 3108-1113A) 1 70*208L (251) SWP B
23 3107-1117A PISTON SPRING (Outer), (FOR RC20~RC21: 3108-1117A) 85*208L (251) SWP B
25 3105-1109B DISCHARGE FIXED RING (MALE ROTOR) 1 130.6*101.7L, S15C
26 4302-260 KM12 BEARING SLOT NUT (MALE ROTOR) 1 M60*2.0 KM12
29 3107-1136A BALANCE PISTON FOR MALE ROTOR 1 105.75*20.08 S45C
30 3107-1132C MALE ROTOR (RC19) 1 S45C
30 3108-1132C MALE ROTOR (RC20~RC21) 1 S45C
31 3107-1023A KEY OF MOTOR ROTOR (RC19) 1 S45C
31 3108-1023A KEY OF MOTOR ROTOR (RC20~RC21) 1 S45C
32 3107-1106B OIL GUIDING RING (MALE ROTOR) 1 150*20t S15C
34 3107-1105A OUTER SPACER RING OF SUCTION BEARING (MALE) 1 150*53.3t, S15C
35 3107-1104A INNER SPACER RING OF SUCTION BEARING (MALE) 1 97*53.3t, S15C
37 3107-2131A MOTOR ROTOR (RC19) 1 RM 600
37 3108-2131A MOTOR ROTOR (RC20~RC21) 1 RM 600
38 3107-1032A MOTOR ROTOR SPACER RING 1 16*32 S45C
42 4307-DB100 DISC SPRING (FEMALE ROTOR) 1 SCHNORR 100
47 3107-1139A BALANCE PISTON FOR FEMALE ROTOR 1 97.75*20.08 S45C
48 3108-1133B FEMALE ROTOR (RC20~RC21) 1 S45C
49 3107-1107B OIL GUIDING RING (FEMALE ROTOR) 1 90*20t S15C
51 3108-1131B BEARING SEAT (RC20~RC21) 1 FC25
54 3101-1102B FIX PIN 2 20*35L S45C
55 4305-102 PLUG 2 1/4" PT
56 4301-108020 BOLT FOR SLIDE VALVE KEY 1 M8*1.25*20L
78
57 3105-1114A SLIDE VALVE KEY 1 27*26*14.5
58 3108-1512B SLIDE VALVE, Vi=2.2 (RC20~RC21) 1 FCD45
59 4301-112035 BOLT 8 M12*1.75*35L
62 4805-01 MAGNETICS 2 40*25*10
63 3108-1141B COMPRESSOR CASING (RC20~RC21) 1 FC25
64 3107-1143A OIL FILTER 1 40*200
68 4301-112035 BOLT 8 M12*1.75*35L
69 4301-302 POWER BOLT 6 FUSITE X4901
70 4201-VA122 POWER BOLT O-RING 6 A.R.P122, VITON
71 4302-412 COPPER NUT (FOR POWER BOLT) 6 M12*1.75
73 3101-1043A COPPER NUT 6 M12*1.75
74 4301-301 SCREW FOR PTC WIRING 2 FUSITE X4914
76 3101-1041C MOTOR CABLE COVER PLATE 1 FC25
77 3101-1006A-3 GASKET (FOR MOTOR CABLE COVER PLATE) 1 REINZ-AFM 34, 1.5t
78 4401-30 NUT 3 M8*0.75
79 4401-30 WASHER 3 M8
80 4401-22 SOLENOID COIL 3
3101-1003A SOLENOID VALVE GASKET 3 NOK,1515SPS
82 4301-804012 BOLT 12 M4*0.7*12L
83 3101-1145E CAPILLARY 1 1/4" F 2.6
84 4304-101 90 ELBOW 2 1/4" NPT A-4890 90
85 4304-105 5/8" CONNECTOR 1 5/8"F*1/2NPT
86 4804-01 OIL SIGHT GLASS (O-RING INCLUDED) 1 ALCO
87 4305-102 PLUG (O-RING INCLUDED) 1 3/4" PF
88 4304-111 3/4" CONNECTOR 3/4" F*1/2 NPT
90 4301-106016 BOLT 4 M6*1*16L
91 4303-248 WASHER 1 1/2"*2.5mm
93 4301-112020 BOLT 1 M12*1.75*20L
94 3119-2250A MOTOR STATOR (RC20~RC21) 1 60Hz, 380V
96 3107-2101B MOTOR CASING (RC19) 1 FC30
96 3108-2101B MOTOR CASING (RC20~RC21) 1 FC30
97 4301-116055 BOLT (FOR MOTOR CASING) 24 M16*20*55L
98 3107-2102D FIXED BOLTOF MOTOR STATOR 1 M28*1.5, 79L
99 3107-2105B WASHER (FOR FIXED BOLT OF MOTOR STATOR) 1 26.7*24L
100 4301-116060 BOLT 8 M16*2.0*60L
101 3103-1042A M16 SPRING WASHER 8 30*5t
102 3107-1018A FLANGE 1 5
103 3107-1016A FLANGE SHELF 1 5
104 3107-1004A-3 GASKET FOR 5 FLANGE 1 REINZ-AFM 34, 1.5t
105 3107-1054A GASKET FOR SUCTION FILTER 1 TEFLON 1.5t
106 3107-1024C SUCTION FILTER 1 60 mesh
107 3107-1055A SPRING 1 70*50L, SWP B
108 3104-1004A-3 GASKET FOR SUCTION FILTER FLANGE 1 REINZ-AFM 34, 1.5t
109 3107-1053A SUCTION FILTER FLANGE 1 226*20t, SS400
110 4301-120065 BOLT (FOR SUCTION FLANGE) 4 M20*2.5*65L
79
1 3142-1131B BEARING SEAT 1 FCD-50
2 3142-1132B MALE SCREW ROTOR 1 SAE 1141
3 3142-1133B FEMALE SCREW ROTOR 1 SAE 1141
4 3142-1137A MALE ROTOR INNER SPACER RING 1 S45C
5 3143-1104A MALE ROTOR SPACER RING 1 S15C, 110 * 163L
6 3108-1023B MOTOR ROTOR KEY 1 S45C, 14 * 22 * 260L
7 4102-NU313E MALE ROTOR DISCHARGE RADIAL BEARING 1 NU 313E
8 4102-NU2313E FEMALE ROTOR DISCHARGE RADIAL BEARING 1 NU 2313E
9 3142-113AA MALE AND FEMALE ROTOR OUTER SPACER RING 2 S45C
10 4101-7313BUO MALE AND FEMALE ROTOR DISCHARGE AXIAL BEARING 5 7313 BUO
11 4302-265 KM 13 BEARING LOCK NUT 2 M65 * 2.0
12 3142-1111B FEMALE ROTOR DISCHARGE BEARING FIXED RING 1 S15C
13 3142-1109B MALE ROTOR DISCHARGE BEARING FIXED RING 1 S15C
14 4307-DB140 DISCHARGE BEARING DISC SPRING 2
15 4201-VA355 O-RING 2 A.R.P. 355 VITON
16 3142-1118A DISCHARGE BEARING COVER 2 SS400, 140.8 * 22t
18 4301-116035 DISCHARGE COVER PLATE SCREW BOLTS 12 M16 * 35L
20 4301-116055 SCREW BOLT 6
22 3142-1017A-3 DISCHARGE FLANGE GASKET 1 REINZ-AFM 34, 1.5t
23 3107-101AA FLANGE COUPLING 1
24 3142-1020A DISCHARGE FLANGE 5 1 SS400, 270 * 25t
25 3103-1042A SPRING WASHER SS400, 30 * 5t
26 4301-120060 DISCHARGE FLANGE SCREW BOLTS 12 M20 * 2.5 * 60L
27 3142-1121C PISTON CYLINDER 1 FCD50
28 4201-VA354 O-RING 1 A.R.P. 354, VITON
29 4301-116045 SCREW BOLT 6 M16 * 45L
30 4303-316 SPRING WASHER
31 3142-1113A PISTON SPRING 1 SWP B
32 3142-1115A PISTON ROD 1 SNCM 439
35 4201-CA349 PISTON O-RING 1 A.R.P. 349 CR70
36 4202-T130 PISTON RING 1 GS55044 1300
37 3142-1116B PISTON 1 S15C
38 3142-1037A SPRING WASHER 1 SS400, 34 * 5t
40 4201-VA351 O-RING 1 A.R.P.351 VITON
41 3142-1122B CYLINDER COVER 1 SS400
42 4301-112040 CYLINDER COVER SCREW BOLTS 8 M12 * 1.75 * 40L
43 4301-116055 BEARING SEAT SCREW BOLTS 13 M16 * 55L
45 4401-32 SOLENOID VALVE (NC) 3 O.D.E. 2743K0R30 4344
46 4301-804020 SOLENOID VALVE SCREW BOLTS 12
47 4402-03 SOLENOID COIL 3 O.D.E. BDV08224DU, 50/60 Hz
48 4302-104 WASHER 3
49 4303-104 SCREW NUT 3
50 4304-106 ANGLE VALVE NPT 1 CASTEL 6110/22,SAE * NPT
51 4302-301 COPPER COVER 1 A 414
52 4302-303 COPPER SCREW NUT 1 A 414
53 4304-102 NPT CONNECTOR 1 F * NPT, A 4585
54 4302-303 COPPER COVER 1 F A 5051
56 4305-102 PLUG PT 1 PT * 11L
58 4304-201 NPT TERMINAL 1 F * NPT, CD1414
59 3142-1129A TUBE 1
60 3142-1128A TUBE 1
61 3142-1127A TUBE 1 , 450L
64 4304-101 NPT CONNECTOR, 90 ELBOW 1 F * NPT, A - 4890
65 3142-1141A COMPRESSOR CASING 1 FCD 50
80
69 4302-301 COPPER COVER 1 F A 5051
71 4201-VP010 O-RING 1 P010 VITON
72 3142-1094B 3/8 NPT CONNECTOR 1 C3603, 3
73 4302-312 COPPER COVER 1 3/8 F
75 3107-1151A-3 ECONOMIZER FLANGE GASKET 1 REINZ-AFM 34, 1.5t
76 3107-1152A ECONOMIZER FLANGE HOLE COVER 1 40 * 3t
77 3107-1150B ECONOMIZER FLANGE 1
78 4301-112035 ECONOMIZER FLANGE SCREW BOLTS 2 M12 * 1.7 * 35L
79 4201-VP010 O-RING 1 P010 VITON
81 3142-1512B SLIDE VALVE Vi 2.2 1 FCD 600
82 3142-1172A CHECK VALVE 1
83 3142-1174A SLIDE VALVE KEY 1 S45C ~ S55C
84 3201-1114A SLIDE VALVE KEY 1 S45C
85 4301-108016 SCREW BOLT 1
87 3142-1092A BASE 1 FC25
88 4301-116090 SCREW BOLT 2 M16 * 2.0p * 90L
89 4301-112090 SCREW BOLT 2
91 3142-1153A 1 PLUG 1
92 3142-1094B 3/8 NPT CONNECTOR 1 C3603, 3
93 4302-312 COPPER COVER 1 3/8 F
95 3142-1102A GUIDE PIN 2 S45C
96 4102-NU2318E MALE ROTOR SUCTION BEARING 1 NU2318ECP
97 3142-1108B MALE ROTOR SUCTION BEARING COVER 1 A2017BE T42
98 4303-106 WASHER 4
99 4301-106016 SCREW BOLTS 4 M6 * 1 * 16L
100 4303-248 WASHER 1 31.9 * 12.5 * 2.3t
101 4303-312 M12 SPRING WASHER 1
102 4301-112020 SCREW BOLTS 1
103 4102-NJ2310E FEMALE ROTOR SUCTION BEARING 1 NJ2310ECP
104 3142-1110A FEMALE ROTOR SUCTION BEARING COVER 1 SS400, 17t
105 4301-110055 SCREW BOLT 12 M20 * 2.5 * 55L
108 3142-1019A SUCTION FLANGE 1 SS400, 305 * 32t
109 3142-1004A-3 SUCTION FLANGE GASKET 1 REINZ-AFM 34, 1.5t
110 3142-1024A SUCTION FILTER 1 60 MESH/INCH
111 4201-VP165 O-RING 2 P165 VITON
114 3142-1018A 6 FLANGE 1 SS400, 305 * 32t
115 3103-1042A M20 WASHER 39 SS400, 30 * 5t
116 4301-120055 SCREW BOLTS 13 M20 * 2.5 * 55L
117 3142-2101A MOTOR CASING 1 FCD50
118 3142-2320A MOTOR STATOR ASSEMBLY 1
119 3142-2103A MOTOR STATOR HOLDER 2 SS400
120 4307-DB031 WASHER 10 DB 31.5
121 4301-116070 SCREW BOLTS 10 M16 * 2.0p * 70L
123 3142-2201A MOTOR COVER 1 FCD50
124 4301-116065 SCREW BOLTS 24 M16 * 65L
129 4405-01 BALL VALVE 1 RIKO, RFS 2 2, SUS316
81

131 4201-VP036 O-RING 1 P36 VITON
132 3142-1149A LEVEL SWITCH PLUG 1 S45C
133 4806-28 3/8 PF PLUG 1 3/8 PF
134 5107-01 TUBE 1
135 3142-1092A BASE 1 FC25
136 4301-116090 SCREW BOLT 2 M16 * 2.0p * 90L
137 4301-116050 SCREW BOLT 4 M16 * 2.0p * 50L
140 3142-2104A MOTOR LIQUID INJECTION FLANGE 1 SS400
142 4301-610 POWER BOLT 6 AUBURN F610, 750 Amp
143 4302-116 SCREW NUT 6 M16
145 4301-301 TEMPERATURE SENSOR SCREW BOLTS 4 FUSITE 20 61862
146 3142-1014A CABLE BOX GASKET 1
147 3142-1012B CABLE BOX 1 600 * 370L * 2.0t
148 3142-1013B CABLE BOX COVER 1 604 * 374L * 1.6t
150 3138-1021A CABLE BOX FLANGE 2
151 4301-108016 SCREW BOLTS 8
152 4806-33 CABLE BOX HOLE PLUG 4 19, HP 19
153 4301-108016 SCREW BOLTS 6 M8 * 16L
154 4301-108016 SCREW BOLTS 4 M8 * 16L
155 4302-104 SCREW NUT 2
156 4303-304 SPRING WASHER 2
157 4303-104 WASHER 2
158 4405-35 MOTOR PROTECTIVE CONTROLLER, INT 69, 110V 1 KRIWAN, 52A120S10
159 4301-104020 SCREW BOLTS 2 M4 * 20L
160 3101-1004A-3 FLANGE GASKET 1 REINZ-AFM 34, 1.5t
161 3142-2105A LIQUID INJECTION FLANGE 1 SS400
164 4302-301 COPPER COVER 1 F A 5051
165 4301-120050 SCREW BOLTS 4 M20 * 2.5 * 50L
166 4301-116065 SCREW BOLTS 24 M16 * 65L
82
1 3143-1131B BEARING SEAT 1 FCD-50
2 3143-1132B MALE SCREW ROTOR 1 SAE 1141
3 3143-1133B FEMALE SCREW ROTOR 1 SAE 1141
4 3142-1137A MALE ROTOR INNER SPACER RING 1 S45C
5 3143-1104A MALE ROTOR SPACER RING 1 S15C, 110 * 163L
6 3108-1023B MOTOR ROTOR KEY 1 S45C, 14 * 22 * 260L
7 4102-NU313E MALE ROTOR DISCHARGE RADIAL BEARING 1 NU 313E
8 4102-NU2313E FEMALE ROTOR DISCHARGE RADIAL BEARING 1 NU 2313E
9 3142-113AA MALE AND FEMALE ROTOR OUTER SPACER RING 2 S45C
10 4101-7313BUO MALE AND FEMALE ROTOR DISCHARGE AXIAL BEARING 5 7313 BUO
11 4302-265 KM 13 BEARING LOCK NUT 2 M65 * 2.0
12 3142-1111B FEMALE ROTOR DISCHARGE BEARING FIXED RING 1 S15C
13 3142-1109B MALE ROTOR DISCHARGE BEARING FIXED RING 1 S15C
14 4307-DB140 DISCHARGE BEARING DISC SPRING 2
16 3142-1118A DISCHARGE BEARING COVER 2 SS400, 140.8 * 22t
18 4301-116035 DISCHARGE COVER PLATE SCREW BOLTS 12 M16 * 35L
20 4301-116055 SCREW BOLT 6
22 3142-1017A-3 DISCHARGE FLANGE GASKET 1 REINZ-AFM 34, 1.5t
24 3142-1020A DISCHARGE FLANGE 5 1 SS400, 270 * 25t
25 3103-1042A SPRING WASHER SS400, 30 * 5t
26 4301-120060 DISCHARGE FLANGE SCREW BOLTS 12 M20 * 2.5 * 60L
27 3142-1121C PISTON CYLINDER 1 FCD50
28 4201-VA354 O-RING 1 A.R.P. 354, VITON
29 4301-116045 SCREW BOLT 6 M16 * 45L
30 4303-316 SPRING WASHER
31 3143-1113A PISTON SPRING 1 SWP B
32 3143-1115A PISTON ROD 1 SNCM 439
34 5112-GM69 PISTON GUIDE RING 1 TURCITE T47
35 4201-CA349 PISTON O-RING 1 A.R.P. 349 CR70
36 4202-T130 PISTON RING 1 GS55044 1300
37 3142-1116B PISTON 1 S15C
38 3142-1037A SPRING WASHER 1 SS400, 34 * 5t
41 3142-1122B CYLINDER COVER 1 SS400
42 4301-112040 CYLINDER COVER SCREW BOLTS 8 M12 * 1.75 * 40L
43 4301-116055 BEARING SEAT SCREW BOLTS 13 M16 * 55L
45 4401-32 SOLENOID VALVE (NC) 3 O.D.E. 2743K0R30 4344
46 4301-804020 SOLENOID VALVE SCREW BOLTS 12
47 4402-03 SOLENOID COIL 3 O.D.E. BDV08224DU, 50/60 Hz
48 4302-104 WASHER 3
49 4303-104 SCREW NUT 3
51 4302-301 COPPER COVER 1 A 414
54 4302-303 COPPER COVER 1 F A 5051
56 4305-102 PLUG PT 1 PT * 11L
59 3142-1129A TUBE 1
60 3142-1128A TUBE 1
61 3142-1127A TUBE 1 , 450L
64 4304-101 NPT CONNECTOR, 90 ELBOW 1 F * NPT, A - 4890
83
69 4302-301 COPPER COVER 1 F A 5051
71 4201-VP010 O-RING 1 P010 VITON
72 3142-1094B 3/8 NPT CONNECTOR 1 C3603, 3
73 4302-312 COPPER COVER 1 3/8 F
75 3107-1151A-3 ECONOMIZER FLANGE GASKET 1 REINZ-AFM 34, 1.5t
76 3107-1152A ECONOMIZER FLANGE HOLE COVER 1 40 * 3t
77 3107-1150B ECONOMIZER FLANGE 1
78 4301-112035 ECONOMIZER FLANGE SCREW BOLTS 2 M12 * 1.7 * 35L
79 4201-VP010 O-RING 1 P010 VITON
82 3142-1172A CHECK VALVE 1
83 3142-1174A SLIDE VALVE KEY 1 S45C ~ S55C
84 3201-1114A SLIDE VALVE KEY 1 S45C
85 4301-108016 SCREW BOLT 1
87 3142-1092A BASE 1 FC25
88 4301-116090 SCREW BOLT 2 M16 * 2.0p * 90L
89 4301-112090 SCREW BOLT 2
91 3142-1153A 1 PLUG 1
92 3142-1094B 3/8 NPT CONNECTOR 1 C3603, 3
93 4302-312 COPPER COVER 1 3/8 F
95 3142-1102A GUIDE PIN 2 S45C
96 4102-NU2318E MALE ROTOR SUCTION BEARING 1 NU2318ECP
97 3142-1108B MALE ROTOR SUCTION BEARING COVER 1 A2017BE T42
98 4303-106 WASHER 4
99 4301-106016 SCREW BOLTS 4 M6 * 1 * 16L
100 4303-248 WASHER 1 31.9 * 12.5 * 2.3t
101 4303-312 M12 SPRING WASHER 1
102 4301-112020 SCREW BOLTS 1
103 4102-NJ2310E FEMALE ROTOR SUCTION BEARING 1 NJ2310ECP
104 3142-1110A FEMALE ROTOR SUCTION BEARING COVER 1 SS400, 17t
105 4301-110055 SCREW BOLT 12 M20 * 2.5 * 55L
108 3142-1019A SUCTION FLANGE 1 SS400, 305 * 32t
110 3142-1024A SUCTION FILTER 1 60 MESH/INCH
111 4201-VP165 O-RING 2 P165 VITON
114 3142-1018A 6 FLANGE 1 SS400, 305 * 32t
115 3103-1042A M20 WASHER 39 SS400, 30 * 5t
116 4301-120055 SCREW BOLTS 13 M20 * 2.5 * 55L
117 3143-2101A MOTOR CASING 1 FCD50
118 3142-2320A MOTOR STATOR ASSEMBLY 1
119 3142-2103A MOTOR STATOR HOLDER 2 SS400
120 4307-DB031 WASHER 10 DB 31.5
121 4301-116070 SCREW BOLTS 10 M16 * 2.0p * 70L
123 3142-2201A MOTOR COVER 1 FCD50
124 4301-116065 SCREW BOLTS 24 M16 * 65L
129 4405-01 BALL VALVE 1 RIKO, RFS 2 2, SUS316
84

131 4201-VP036 O-RING 1 P36 VITON
132 3142-1149A LEVEL SWITCH PLUG 1 S45C
133 4806-28 3/8 PF PLUG 1 3/8 PF
134 5107-01 TUBE 1
135 3142-1092A BASE 1 FC25
136 4301-116090 SCREW BOLT 2 M16 * 2.0p * 90L
137 4301-116050 SCREW BOLT 4 M16 * 2.0p * 50L
140 3142-2104A MOTOR LIQUID INJECTION FLANGE 1 SS400
142 4301-610 POWER BOLT 6 AUBURN F610, 750 Amp
143 4302-116 SCREW NUT 6 M16
145 4301-301 TEMPERATURE SENSOR SCREW BOLTS 4 FUSITE 20 61862
146 3142-1014A CABLE BOX GASKET 1
147 3142-1012B CABLE BOX 1 600 * 370L * 2.0t
148 3142-1013B CABLE BOX COVER 1 604 * 374L * 1.6t
150 3138-1021A CABLE BOX FLANGE 2
151 4301-108016 SCREW BOLTS 8
152 4806-33 CABLE BOX HOLE PLUG 4 19, HP 19
153 4301-108016 SCREW BOLTS 6 M8 * 16L
154 4301-108016 SCREW BOLTS 4 M8 * 16L
155 4302-104 SCREW NUT 2
156 4303-304 SPRING WASHER 2
157 4303-104 WASHER 2
159 4301-104020 SCREW BOLTS 2 M4 * 20L
160 3101-1004A-3 FLANGE GASKET 1 REINZ-AFM 34, 1.5t
161 3142-2105A LIQUID INJECTION FLANGE 1 SS400
164 4302-301 COPPER COVER 1 F A 5051
165 4301-120050 SCREW BOLTS 4 M20 * 2.5 * 50L
166 4301-116065 SCREW BOLTS 24 M16 * 65L
85

Hanbell Maintenance Manual

Uploaded by

Copyright:

Available Formats

Hanbell Maintenance Manual

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Hanbell Maintenance Manual

Uploaded by

Copyright:

Available Formats

What are the main components discussed in the manual?

What are the main components discussed in the manual?

What are the main maintenance procedures described?

What are the main maintenance procedures described?

HANBELL SCREW COMPRESSORS

HANBELL PRECISE MACHINERY CO., LTD.

I-1. Dismantle Solenoid Valve 1

II. HOW TO CHANGE 4-STEP TO STEPLESS CAPACITY CONTROL

II-1. Dismantle Capacity Solenoid Valve 4

III. HOW TO CHANGE STEPLESS TO 4-STEP CAPACITY CONTROL

III-1. Dismantle Capacity Solenoid Valve (N.C, SV1) 10

IV. HOW TO REPLACE OIL FILTER, OIL LEVEL SWITCH

IV-1. Dismantle Oil Filter Flange 13

V. HOW TO REPLACE SUCTION FILTER

V-1. Dismantle Suction Flange 18

VI. HOW TO REPLACE CHECK VALVE, OIL SEPARATOR

VI-1. Dismantle Check Valve 20

VII. HOW TO REPLACE MOTOR ASSEMBLY, MOTOR STATOR

VII-1. Dismantle Electrical Cable Plate 24

VIII. HOW TO REPLACE PISTON, PISTON ROD, SLIDE VALVE

VIII-1. Dismantle Oil Separator 34

IX. HOW TO REPLACE MALE & FEMALE ROTORS, BEARINGS

IX-1. Dismantle Bearing Slot Nut 44

List of special tools 59

This HANBELL semi-hermetic twin-screw compressor maintenance manual is

I-1. DISMANTLE SOLENOID VALVE

Step 1. Loosen first the nut of the solenoid valve using

Step 2. Loosen all the screw of capacity solenoid valve

I-2. ASSEMBLY CAPACITY SOLENOID VALVE

Step 1. Put first the two O-rings to each capacity

Step 2. Install the capacity solenoid valve to

O-ring and hole must be

Step 4. Install the capacity solenoid coil on the capacity

II. HOW TO CHANGE 4-STEP TO STEP-LESS CAPACITY CONTROL

Step 1. Loosen the lock nut of the three solenoid valves

Step 2. Loosen all the screws of solenoid valve and

Step 3. Remove the capillary tube from the compressor

II-2. ASSEMBLY COVER PLATE

Step 1. Clean first the surface of the compressor casing

Step 2. Put the two O-ring in the cover plate.

Cover Plate N.O. Solenoid

II-3. ASSEMBLY CAPACITY SOLENOID VALVE (N.C)

Step 1. Put the two O-rings in orifice plate and put it in

Step 3. Install the N.C. capacity solenoid valve and the

Step 4. Put all the screws and tighten it using a wrench.

Step 1. Install first the oil inlet connector in the

Step 2. Install the N.O. capacity solenoid valve in the oil

Step 3. Install the 90 deg. elbow connector in the

Step 4. Install the capillary tube in the two 90 deg. elbow

III. HOW TO CHANGE STEP-LESS TO 4-STEP CAPACITY CONTROL

Step 1. Dismantle the solenoid coil of the capacity

Step 2. Loosen all the screw of capacity cover plate

Step 3. Loosen all the screw of capacity solenoid valve

III-2. DISMANTLE CAPACITY SOLENOID VALVE (N.O)

Step 1. Loosen the capillary tube from 90 deg. elbow

Step 3. Loosen the N.O capacity solenoid valve from oil

Step 4. Loosen the oil inlet connector from compressor

III-3. ASSEMBLY CAPILLARY

Step 1. Install first the 90 deg. elbow connector (with