Local Area ServerS DATA CASH TELECOM- e-business INDUSTRIAL ELECTRO- EMERGENCY

Networks CENTRES REGISTERS MUNICATIONS (Servers Farms, PLCs MEDICAL DEVICES

(LAN) DEVICES ISP/ASP/POP) DEVICES (Lights/Alarms)

Multi Sentry
10-20 kVA
Single-phase

10-120 kVA
Three-phase

Highlights
Complete power
range from 10
up to 120 kVA
Small footprint
High efficiency
up to 96,5%
Zero Impact Source
Advanced
communication

The MULTI SENTRY series is ideal VFI-SS-111 classification, as defined in

for protecting data centre and IEC EN 62040-3.
telecommunications systems, IT networks MULTI SENTRY: designed and built
and critical systems where poor power using state of the art technology and
quality can lead to a loss of operations components, and controlled by the DSP
and service. (Digital Signal Processor) microprocessor,
The MULTI SENTRY series is available in to provide maximum protection to
10-12 15-20 kVA models with three-phase the powered loads with no impact on
and single-phase input and single-phase downsteam systems and optimise energy
output, and 10-12-15- 20-30-40-60-80- savings.
100-120 kVA models with three-phase Its highly flexible design allows full
input and output with On-line double compatibility both with three-phase and
conversion technology, according to the single-phase power supplies.
Zero impact source
Thanks to the technology used, MULTI
MST 40
SENTRY solves installation problems in Traditional UPS 40kVA

% Efficiency
systems where the power supply has 100
limited installed power, where the UPS is 98
also powered by a generator or where
96
there are compatibility problems with
loads that generate harmonic currents; 94
MULTI SENTRY has zero impact on its 92
power source, being either the mains 90
power supply or a generator:
88
input current distortion of less than 3%
Input power factor 0.99
86
power walk-in function that ensures a 84
progressive start-up of the rectifier 82
start-up delay function, to restart the
80
rectifiers when mains power is restored
78
if there are several UPS in the system.
In addition, MULTI SENTRY plays a filter 76
and power factor correction role in the 0 20 30 40 60 80 100 120
power network upstream of the UPS, as it % load
eliminates harmonic components and the
batteries (residual AC component) current is one of
reactive power, generated by the
Two-level voltage recharge according to the most important causes of a reduction
powered utilities.
IU characteristic in reliability and battery life.
Charge block system to reduce Thanks to a high frequency battery
High output
electrolyte consumption and further charger, MULTI SENTRY reduces this
Using state-of-the-art technologies
extend the life of VRLA batteries. value to negligible levels, prolonging
three-level NPC inverters have been
Compensation of recharge voltage as battery life and maintaining high
designed which ensure a high output of
a function of the temperature in order performance over a long period of time.
up to 96.5%.
to prevent excessive charges or battery Wide voltage range: the rectifier is
These technology solutions allow for a
overheating. designed for operation with a wide range
saving of more than 50% of the energy
Battery tests to quickly diagnose any of input voltage values (up to - 40% at
dissipated in a year, compared to a
reduction in performance or problems half load), reducing the need for battery
similar product on the market with 92%
with the batteries. discharge and thus helping to battery
output.
Protection against deep discharges: extend life.
The exceptional performance makes it
during extended low-load discharges,
possible to recover the initial investment
the end-of-discharge voltage is increased Maximum reliability
cost in less than three years of operation.
as recommended by the battery and availability
manufacturers, to prevent damage to or Connect up to 6 units in redundant (N+1)
Battery care system
decreased performance of the batteries. or parallel configuration. The UPS
Proper battery care is critical to ensuring
Ripple current: the recharge ripple continues to operate in parallel even in
the correct operation of a UPS in
emergency conditions.
The Riello UPS Battery Care System
consists of a series of features and
capabilities that allow for battery
management in order to obtain the best
performance possible and extend their
operating life.
Battery charging: MULTI SENTRY is
suitable for use with hermetically sealed
lead-acid (VRLA), AGM and GEL batteries
and Open Cup and Nickel Cadmium
batteries.
Depending on the battery type, different
charging methods are available.
One-level voltage recharge, typically
used for more common VRLA AGM

www.riello-ups.com
 the event of an interruption in the Advanced multi-platform,
connection cable (closed loop). communication for all operating
systems and network environments:
Low management cost PowerShield3 supervision and
The technology and the choice of high shutdown software for Windows
performance components, allows MULTI operating systems 7, 2008, Vista,
SENTRY to achieve exceptional 2003, XP, Linux Mac OS X, Sun Solaris,
performance and output, with an Linux, Novell and other Unix operating
extremely compact overall size systems.
smallest overall footprint is only Compatible with the Riello
0.26sqm for MULTI SENTRY 20kVA TeleNetGuard service
with batteries RS232 serial port or USB
the type of input stage ensures a 3 slots for the installation of optional
power factor close to 1 and low current communications accessories like
distortion without adding bulky and network adapters, voltage-free contacts
expensive filters etc.
output power at 0.9 power factor that REPO Remote Emergency Power
provides up to 15% more active power Off for switching off the UPS with the
On-line, Eco, Smart Active and
than a standard UPS on the market, remote emergency button
Stand By Off operating modes that
guaranteeing a greater margin in UPS Input for the connection of the auxiliary
are compatible with compatible with
sizing for potential load increases. contact of an external manual bypass
applications for centralised power
systems (CSS). Input for synchronisation from an
Flexibility external source
frequency converter mode
MULTI SENTRY is suitable for use in a Graphic mimic panel display for remote
configurable EnergyShare sockets to
wide range of applications, thanks to its connection.
ensure backup for the most critical
configuration flexibility, accessories and
loads or those programmed to operate
options, and performance:
only when mains power fails
suitable for powering capacitive loads,
Cold Start to switch on the UPS even
such as Blade servers, without any
when there is no mains power
reduction in active power from 0.9 lead
MST/MSM version: cabinet
to 0.9 lag
(1320x440x850mm HLW) for optimised
solutions when medium to long-term
(% PA UPS) P
Q
runtime is required.
optional temperature sensor for external
battery cabinets, to assist the recharge
100 CAPACITIVE
voltage compensation
additional battery chargers to optimise
80
charge time
60 PF 0.9 optional dual input to mains power
e.g.: 10 kVA UPS
powers
supply
40 9 kW load isolation transformers to vary neutral
PF 1 connectivity in the event of separate
20 e.g.: 10 kVA UPS
powers
power sources or for galvanic isolation
% PA 0
9 kW load between input and output
25 50 75 100 (% P UPS) P battery cabinets of different sizes and
20 capacities, for providing extended
PF 0.9 runtimes.
40
e.g.: 10 kVA UPS
powers
60
9 kW load Advanced communication
MULTI SENTRY is equipped with a graphic
80 display (240x128 pixel backlit) that provides
INDUCTIVE UPS information, measurements, status,
100
and alarms in different languages and
displays wave forms and voltage/current.
(% PA UPS) P The default screen shows the status of the
Q
UPS graphically indicating the status of the
various blocks (rectifier, batteries, inverter,
bypass).

www.riello-ups.com
 battery box

BB 1320 480-T4 / BB 1320 480-T5 BB 1900 480-V6 / BB 1900 480-V7 / BB 1900 480-V8
MODELS BB 1600 480-S5 / AB 1600 480-S5
BB 1320 480-T2 / AB 1320 480-T5 BB 1900 480-V9 / AB 1900 480-V9
MODELS UPS up to 60 kVA up to 80 kVA up to 120 kVA
Dimensions
(mm)

1900
1600
1320

815 860
400 650 750 80
0

details

MST 100 - 120

(front)
EnergyShare PARALLEL MST 60 - 80
SOCKET CONNECTORS (front)
SLOT FOR REPO
MSM 10 - 20
SLOT FOR
COMMUNICATION CONNECTORS COMMUNICATION MST 10 - 40
INTERFACE - AS400 INTERFACE (front)
USB - RS232
REPO SLOT FOR
CONNECTORS - COMMUNICATION MCM 10 - 12 - 15 - 20
PARALLEL AS400 INTERFACE
CONNECTORS USB - RS232 MCT 10 - 12 - 15 - 20
(rear)

SLOT FOR
EnergyShare COMMUNICATION
SOCKETS INTERFACE
BATTERY REMOTE PARALLEL
FUSES CONNECTOR AND CONNECTORS
CONTACTS SERIAL PORT
RS232

USB PORT

INPUT
SWITCH OUTPUT
SWITCH
OUTPUT
SWITCH BYPASS
SWITCH MANUAL BYPASS
MANUAL
BYPASS (OPTIONAL)

BYPASS INPUT OUTPUT

SWITCH SWITCH SWITCH
MANUAL BYPASS
MULTICOM 382 IEC AUXILIARY
AUXILIARY BOARD SOCKETS BYPASS
SLOT SWITCH
(OPTIONAL)

www.riello-ups.com
MODELS MCM/MSM 10 MCM/MSM 12 MCM/MSM 15 MCM/MSM 20
INPUT
Nominal voltage 380-400-415 Vac three-phase with neutral / 220-230-240 single-phase
Nominal frequency 50 or 60 Hz
Frequency tolerance 40 72 Hz
Power factor at full load 0.99
Current distortion thdi 3%
BY PASS
Nominal voltage 220-230-240 Vac
Number of phases 1
Voltage tolerance 180 264 V (selectable)
Nominal frequency 50 or 60 Hz (selectable)
Frequency tolerance 5 (selectable)
OUTPUT
Nominal power (kVA) 10 12 15 20
Active power (kW) 8 9.6 12 16
Power factor 0.8
Number of phases 1
Nominal voltage (V) 220-230-240 Vac (selectable)
Static variation 1%
Dynamic variation 3%
Crest factor (Ipeak/Irms) 3:1
Voltage distortion < 1% with linear load / < 3% with non-linear load
Frequency 50 or 60 Hz
Frequency stability
0.01%
during battery operation
Overload at Pf 0.8 110% for 10 minutes, 133% for 1 minute, 150% for 5 seconds
BATTERIES
Type VRLA AGM/GEL
Charging time 6 hours
INFO FOR INSTALLATION
Weight without
internal batteries (kg) 80/105 82/110 90/115 95/120
(MCM/MSM)
930 x 320 x 840 (MCM version)
Dimensions (hwd) (mm)
1320 x 440 x 850 (MSM version)
Communication 3 slot for communications interface /RS232/USB
Ambient temperature 0C / +40C
Relative humidity 90% non-condensing
Colour Dark grey RAL 7016
Noise level < 52 dBA a 1 m
Protection level IP20
Smart Active Output up to 98%

Directive EMC 2004/108/CE Electromagnetic Compatibility Directive

Regulations Standards: Safety IEC EN 62040-1; EMC IEC EN 62040-2 C2
Classification according to IEC 62040-3 (Voltage Frequency Independent) VFI - SS 111

www.riello-ups.com
 MCT/MST MCT/MST MCT/MST MCT/MST
MODELS MST 30 MST 40 MST 60 MST 80 MST 100 MST 120
10 12 15 20
INPUT
Nominal voltage 380-400-415 Vac three-phase with neutral
Nominal frequency 50 or 60 Hz
Frequency tolerance 40 72 Hz
Power factor at full load 0.99
Current distortion thdi 3%
BY PASS
Nominal voltage 380-400-415 Vac three-phase with neutral
Number of phases 3+N
Voltage tolerance 180 264 V (selectable)
Nominal frequency 50 or 60 Hz (selectable)
Frequency tolerance 5 (selectable)
OUTPUT
Nominal power (kVA) 10 12 15 20 30 40 60 80 100 120
Active power (kW) 9 10.8 13.5 18 27 36 54 72 90 108
Power factor 0.9
Number of phases 3+N
Nominal voltage (V) 380-400-415 Vac (selectable)
Static variation 1%
Dynamic variation 3%
Crest factor (Ipeak/Irms) 3:1
Voltage distortion 1% with linear load / 3% with non-linear load
Frequency 50 or 60 Hz
Frequency stability
0.01%
during battery operation
Overload at Pf 0.8 115% unlimited, 125% for 10 minutes, 150% for 1 minute, 168% for 5 seconds
BATTERIES
Type VRLA AGM/GEL
Charging time 6 hours
INFO FOR INSTALLATION
Weight without

- In the interest of product improvement Riello UPS reserves the right to change specifications without notice.
internal batteries (kg) 80/105 82/110 90/115 90/115 135 145 190 200 370 380
(MCT/MST)
930 x 320 x 840 (versione MCT)
Dimensions (hwd) (mm) 1320 x 440 x 850 1600 x 500 x 850 1900 x 750 x 855
1320 x 440 x 850 (versione MST)
Communication 3 slot for communications interface /RS232/USB
Ambient temperature 0C / +40C
Relative humidity 90% non-condensing
Colour Dark grey RAL 7016
Noise level < 52 dBA a 1 m < 48 dBA a 1 m < 52 dBA a 1 m < 65 dBA a 1 m
Protection level IP20
Smart Active Output up to 99%
European directives L V 2006/95/CE Low Voltage
Directive EMC 2004/108/CE Electromagnetic Compatibility Directive
Regulations
Standards: Safety IEC EN 62040-1; EMC IEC EN 62040-2 C2
Classification according to IEC 62040-3 (Voltage Frequency Independent) VFI - SS 111
FLVMSTGB101RU

LEGNAGO, Headquarters
RIELLO ELETTRONICA

Production and Sales Manag.

Viale Europa, 7
37045 Legnago (VR)
Tel.: +39 0442 635811
www.riello-ups.com
Fax: +39 0442 629098 [email protected]